Mitsubishi Electronics GOT1000 Switch setting, 18.4.3Ethernet setting

18.4.3Ethernet setting

Item		Description	Range
Host		The host is displayed. (The host	―
		is indicated with an asterisk (*))
		Set the network No. of the	Network No. of
N/W No.		connected Ethernet module.
			CNC*1
		(Default: blank)
		Set the station No. of the
PLC No.		connected Ethernet module.	Station No. of CNC
		(Default: blank)
		Set the type of the connected
Type		Ethernet module.	AJ71QE71
		(Default: QJ71E71)
		Set the IP address of the
IP Address		connected Ethernet module.	IP address of CNC
		(Default: blank)
		Set the port No. of the connected
Port No.		Ethernet module.	5001
		(Default: 5001)
Communication		UDP (fixed)	UDP (fixed)
*1	For operating CNC monitor function, set N/W No. to "239".

18.4.4							Switch setting												17
 Switch setting (GT15-75J71P23-Z, GT15-																			ROBOT CONTROLLER CONNECTION
75JBR13-Z)
POINT																			18
	Switch setting of the communication unit
																				CONNECTION
	For details of each setting switch and LED, refer to the
	When using the MELSECNET/H communication unit,
	the switch setting is not needed.
	following manual.																			CNC
					GT15 MELSECNET/10 communication unit
																			19
					User's Manual
							GT15-75J71LP23-Z, GT15-75J71BR13-Z												MULTIGOT-DROP	CONNECTION
					RUN	POWER
					PC
					DUAL	D.LINK
					SW.E	T.PASS													20
					M/S.E					E
				E PRM.E		GOT R/W
				R	CRC	CRC				R
				R	OVER	OVER				R
				O	AB.IF	AB.IF				O
				R						R
					TIME	TIME
					DATA	DATA
					UNDER	UNDER
					LOOP	LOOP													GT12,GT14,-MULTIPLE GT10GT11, FUNCTIONCONNECTION
					SD	SD
					RD	RD
					F.LOOP	R.LOOP
												4	5	6			(2)
												1	0	9
												3		7	GROUP No.
												2		8
(4)								7	8	9A		1	5	6
							21		0FED				0	9 8
							6			B		4		7
						MODE	45			C		3			X100
							3					2
							4		5	6		4	5	6		No.	(1)
							1		0	9 8		1	0	9 8
(3)							3			7	X10	3		7	X10 NETWORK
							2					2
						No.	4		5	6		4	5	6
					STATION														21
							3			7	X1	3		7	X1
							2			8		2		8
							1		0	9		1	0	9
(1) Network number setting switch																			-MULTICHANNEL FUNCTION
2			8		X100
Network number setting																Description		Set value
				switch
4	5	6
3			7
1	0	9																	22
																Set the network No. of the
	5	6
4			7													MELSECNET/10
3					X10		NETWORK											1 to 239	TRANSPARENTFA
2			8													communication unit.				FUNCTION
1	0	9					No.
																(Default: 001)
	5
4		6
3			7		X1
2			8
1	0	9
(2) Group number setting switch
Group number setting																Description		Set value
				switch
			5	6												Set the group No. of the		0: No group
	4															MELSECNET/10
	3				7	GROUP No.												setting
2					8											communication unit.
		1	0	9														(fixed)*1
																(Default: 0)
			*1 The GOT does not use the group number.
						Specify "0".

18. CNC CONNECTION	18 - 13
18.4 GOT Side Settings