(3)Communication confirmation

The RDY LED on the Ethernet module turn on when the module is ready to communicate.

For confirming the communication state, refer to the following.

8.3.4 ■Confirming the communication state of Ethernet module

AJ71QE71N3-T, AJ71QE71N-B5,

A1SJ71QE71N3-T, A1SJ71QE71N-B5,

AJ71QE71N-B2, AJ71QE71N-T,

A1SJ71QE71N-B2, A1SJ71QE71N-T,

AJ71QE71N-B5T, AJ71QE71,

A1SJ71QE71N-B5T,A1SJ71QE71-B5,

AJ71QE71-B5

 

A1SJ71QE71-B2

 

RUN

BUF1

RUN

BUF1

RDY

BUF2

RDY

BUF2

BUF3

BSY

BUF3

BSY

BUF4

SW.ERR.

BUF4

SW.ERR.

BUF5

COM.ERR.

BUF5

COM.ERR.

BUF6

TEST

BUF6

CPU R/W

BUF7

TEST ERR.

BUF7

 

BUF8

 

CPU R/W

BUF8

 

 

TEST

TEST ERR.

[Controller Setting] and [Ethernet] of GT Designer3

(1) Controller setting

Item

Set value (Use default value)

GOT NET No.

1

 

 

GOT PLC No.

1

 

 

GOT IP Address

192.168.0.18

 

 

GOT Port No.

5001

(Communication)

 

 

 

GOT Port No.

5014

(Ethernet Download)

 

 

 

Default Gateway

0.0.0.0

 

 

Subnet Mask

255.255.255.0

 

 

Retry

3times

 

 

Startup Time

3sec

 

 

Timeout Time

3sec

 

 

Delay Time

0ms

 

 

(2) Ethernet setting

 

Item

Set value

 

Host

*

 

 

 

 

N/W No.

1

 

 

 

Ethernet

PLC No.

2

 

 

Type

AJ71QE71

setting No.1

 

 

 

IP address

192.168.0.19

 

 

 

 

Port No.

5001 (fixed)

 

 

 

 

Communication

UDP (fixed)

 

 

 

POINT

[Controller Setting] and [Ethernet] of GT Designer3

For [Controller Setting] and [Ethernet] of GT Designer3, refer to the following.

8.3.1 Setting communication interface (Communication settings)

8.4.6Connecting to Ethernet module (A Series)

This section describes the settings of the GOT and Ethernet module (A Series) in the following case of the system configuration.

POINT

Ethernet module (A Series)

For details of the Ethernet module (A Series), refer to the following manual.

For A Ethernet Interface Module User’s Manual

System configuration

■ [Controller Setting] and [Ethernet] of GT

Designer3

<GOT> (The settings other than the following are set to the default)

Network No.

: 1

PLC No.

: 1

IP address

: 192.168.0.18

Port No.

: 5001

Communication format : UDP (fixed)

*1

<Ethernet module> (The settings other than the

following are set to the default)

Network No.

: 1 (virtual)*2

PLC No.

: 2 (virtual)*2

IP address

: 192.168.0.19

Port No.

: 5001

Communication format

: UDP(fixed)

■ Switch settings of Ethernet module ■ Sequence program

*1 The Ethernet module is mounted on the base unit slot 0. The Start I/O No. of the Ethernet module is set to "0".

*2 These setting items do not exist at the PLC side. However, the virtual values must be set on the GOT side.

■ [Controller Setting] and [Ethernet] of GT Designer3

1

PREPARATORYFORPROCEDURESMONITORING 2

RANGESETBE

DEVICE CANTHAT 3

RANGEACCESS MONITORINGFOR 4

MONITORTOREDUNTANTSYSTEM HOW 5

CONNECTIONBUS 6

DIRECTTOCONNECTIONCPU 7

LINKCOMPUTER CONNECTION 8

ETHERNETCONNECTION

8. ETHERNET CONNECTION

8 - 33

8.4 PLC Side Setting