(5) Mode setting switch
|
|
|
|
|
|
|
|
|
|
|
|
|
| Setting |
| Mode setting switch |
|
|
|
| Description | Set | necessity at | ||||||
|
|
|
|
| value | GOT | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| connection |
|
|
|
|
|
|
|
|
|
|
| Mode setting | 0 |
| |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| E |
|
| ||||
| MODE |
|
|
|
| BCD |
|
|
|
| ||||
|
| 9 | A |
| F |
| (Online) | (fixed) |
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| 7 |
| 0 |
|
| ||||||
0 : ONLINE(A.R) |
| 8 |
|
|
|
|
| |||||||
|
|
| 6 |
| 21 |
|
|
|
|
| ||||
2 : OFFLINE |
|
|
|
| 54 | 3 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| : Necessary : As necessary | : Not necessary | ||||||
(6) Condition setting switches |
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Setting |
Condition setting |
|
|
| Setting | Description | Set | necessity at | |||||||
| switches |
|
|
| switch | value | GOT | |||||||
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| connection |
|
|
|
|
|
|
|
|
|
|
|
| Network type |
|
|
|
|
|
|
|
|
| SW1 | (PLC to PLC | OFF |
| ||||
|
|
|
|
|
|
| (fixed) |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| (PC)) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Station type |
|
|
OFF ON |
|
|
| SW2 | (Control | ON |
| |||||||
|
|
| station | (fixed) |
| |||||||||
|
| SW |
|
|
|
|
|
|
|
|
| |||
1(MNG))
2Parameter
3 | SW3 | for using*1 | OFF | |
4 | (common | |||
(fixed) | ||||
5 |
| parameter | ||
|
| |||
6 |
| (PRM)) |
| |
|
|
| ||
7 | SW4 | No. of | OFF | |
8 | SW5 | stations*1 | (fixed) | |
| SW6 | B/W | OFF | |
|
| Total BW | ||
|
| |||
| SW7 | (fixed) | ||
| points*1 | |||
|
| |||
| SW8 | Not used | OFF | |
| (fixed) | |||
|
|
|
: Necessary 
: As necessary 
: Not necessary
*1 The MELSECNET/10 network module can be communicated by default parameters.
For details, refer to the following manual.
For QnA/Q4AR MELSECNET/10 Network System Reference Manual
POINT
When the switch setting (other than the LED indication select switch) is changed
Turn the PLC CPU OFF then ON again, or reset the
PLC CPU.
[Network parameter] of GX Developer
(1) Network parameter
|
| Setting | |
Item | Set value | necessity at | |
GOT | |||
|
| ||
|
| connection | |
Network type | MNET/10 |
| |
(Control station) (fixed) |
| ||
|
| ||
|
|
| |
Start I/O No. | 0000H |
| |
|
|
| |
Network No.*1 | 1 |
| |
|
|
| |
Total stations | 2 |
| |
|
|
| |
Network range assignment | Refer to (2) |
| |
|
|
| |
Refresh parameters |
|
| |
| (Use default value) |
| |
Interlink transmission |
| ||
|
| ||
parameters |
|
| |
|
|
| |
Routing parameters | Refer to (3) |
| |
|
|
|
: Necessary 
: As necessary 
: Not necessary
*1 Specify the same network No. as that of the network number setting switch of the MELSECNET/10 network module.
9
TO CONNECTIONPLC MELSECNET/H(PLCNETWORK)
10
MELSECNET/10 CONNECTION (PLC TO PLC NETWORK)
11
12
13
14
15
CONNECTION
INVERTER
16
CONNECTION
SERVO AMPLIFIER
10. MELSECNET/10 CONNECTION (PLC TO PLC NETWORK) | 10 - 19 |
10.4 PLC Side Setting |
|