Show system, See Also show system on | Nortel Networks 2300 Series

78System Services Commands

show system

Displays system information.

Syntax show system

Defaults None.

Access Enabled.

History

Version 4.0	License field removed. To display license information, use the
	show license command.

Examples To show system information, type the following command:

WSS# show system

==============================================================================

=	WSS
Product Name:	WSS
System Name:	WSS-bldg3
System Countrycode:	US
System Location:	first-floor-bldg3
System Contact:	tamara@example.com
System IP:	192.168.12.7
System idle timeout:	3600
System MAC:	00:0B:0E:00:04:30

==============================================================================

=	2003-11-07 15:45:49
Boot Time:	2003-11-07 15:45:49
Uptime:	13 days 04:29:10

==============================================================================

=	fan1 OK fan2 OK fan3 OK
Fan status:	fan1 OK fan2 OK fan3 OK
Temperature:	temp1 ok temp2 ok temp3 ok
PSU Status:	Lower Power Supply DC ok AC ok Upper Power Supply missing
Memory:	97.04/744.03 (13%)
Total Power Over	29.000
Ethernet :	29.000

==============================================================================

Table 10 describes the fields of show system output.

NN47250-100 (Version 02.51)

Page 78

Image 78

Nortel Networks 2300 Series manual Show system, See Also show system on, Syntax show system, WSS# show system

Contents

Page Copyright 2007-2008 Nortel Networks. All rights reserved Nortel Networks software license agreement Legal Information Exclusive Remedy Software License Agreement Page SSH Source Code Statement OpenSSL Project License Statements NN47250-100 Version How to get help Introducing the Nortel Wlan 2300 System NN47250-102 Version How to get help Getting help from the Nortel web site How to get help NN47250-100 Version Introducing the Nortel Wlan 2300 System Nortel Wlan 2300 System Documentation Planning, Configuration, and Deployment InstallationConfiguration and Management Safety and Advisory Notices Menu Name Command Bold textItalic text Using the Command-Line Interface CLI Conventions Command Prompts Clear interface vlan-idip Set enablepassSet port enable disable port-list Clear fdb dynamic port port-list vlan vlan-id MAC Address Notation MAC Address Wildcards Port Lists Command-Line Editing Using CLI Help WSS# show ip telnet WSS# show i?WSS# show ip ? Set ap port-list ap-numname name Using the Command-Line Interface NN47250-100 Version Enable Access CommandsDisable See Also enable on WSS# set enablepass Enter old password old-password Set enablepassSyntax set enablepass Quit Disable on Enable on Access Commands NN47250-100 Version Clear port type on Port CommandsPort Type Set port type ap on Set ap on Clear ap on Clear ap Clear port counters Clear port-group Clear port media-type Clear port mirror Clear port name Clear port type Network Port DefaultsConfiguration from all the specified ports Syntax clear port type port-list Set port type ap on Set port type wired-auth on Monitor port countersWSS# clear port type Key Controls for Monitor Port Counters Display WSS# monitor port counters Output for monitor port counters Displayed for All OptionsOctets Number of packets received that were 64 bytes long WSS# reset port Reset portSyntax reset port port-list See Also show port counters on Set ap See Also set port on 2360/61-1 to 2382-1 to2380-1 to 2350-1 to See Also reset port on Set portSet port-group Set port media-type WSS# set port-group name server1 1-5 mode onMode on off Syntax set port-group name group-nameport-listmode on off 2380# set port media-type 2 rj45 Set port mirrorSyntax set port media-type port-listrj45 Syntax set port mirror source-portobserver observer-port WSS# set port 1 observer WSS# set port 17 name adminpoolSet port name Syntax set port port name name Set port negotiation Set port poe Set port speed WSS# set port poe 7,9 disableWSS# set port poe 7,9 enable Syntax set port speed port-list10 100 1000 auto Set port trap Syntax set port trap port-listenable disableWSS# set port trap 17-18 enable Set port type ap Port-list List of physical portsRadiotype 11a 11b 11g Radio type AP Access Port Defaults Version New values for model option added WSS# set port type ap 4-6 model 2330 poe enable Set port type wired-authWSS# set port type ap 2 model 2330 poe enable WSS# set ap 1 radio 1 antennatype None Wired Authentication Port DefaultsLast-resort Web-portal Clear port type on Set port type ap on WSS# set port type wired-authShow port counters Port port-list WSS show port counters octets port Show port-groupOutput for show port-group Syntax show port-group name group-name Show port media-type GBIC-The Gbic fiber interface is enabledRJ45-The RJ-45 copper interface is enabled Output for show port media-type Show port mirror Show port poe Output for show port poe See Also set port poe on Syntax show port status port-list Show port statusOutput for show port status WSS# show port status Wa-Wired authentication port Up-The port is enabledDown-The port is disabled No connector-GBIC slot is empty System Services Commands Clear banner motd Clear historySee Also history on Syntax clear prompt Clear promptClear system Wildebeest# clear prompt success change accepted. WSS# Help HelpWSS# clear system location None Quickstart Set auto-configHistory See Also clear history on Syntax set auto-config enable disable Set banner motd WSS# set auto-config enable success change acceptedWSS# save config 2360# set vlan 1 port 7 success change accepted Set confirm Set length WSS# set length Set licenseSyntax set length number-of-lines Syntax set license activation-key See Also show licenses on Set promptSet system contact Syntax set prompt string Syntax set system countrycode code Set system countrycode23x0#set system contact tamara@example.com 23x0#set system country code CA Syntax set system idle-timeout seconds Set system idle-timeoutSee Also show config on WSS# set system idle-timeout Set system ip-address Set system location Set system name Syntax set system name string Show load Show banner motdShow licenses See Also set license on See Also show system on Show license commandShow system Syntax show system Show system output Show tech-support System Services Commands System Services Commands NN47250-100 Version Vlan Commands WSS# clear fdb dynamic Clear fdbWSS# clear fdb static vlan blue WSS# clear fdb port 3,5 Syntax clear security l2-restrict counters vlan vlan-idall Clear security l2-restrictClear security l2-restrict counters All Syntax clear vlan vlan-id port port-list tag tag-value Clear vlanWSS# clear security l2-restrict counters vlan abcair Vlan-id Port port-list WSS# clear vlan green port Set vlan port on Show vlan config onSet fdb WSS# clear vlan red port 4 tag Set fdb agingtime Set security l2-restrictSee Also show fdb agingtime on Syntax set vlan vlan-numname name Enable disableSet vlan name Mode WSS# set vlan 3 name marigold Set vlan portSee Also set vlan port on Syntax set vlan vlan-id port port-list tag tag-value WSS# set vlan beige port 16 tag Set vlan tunnel-affinityShow fdb Syntax set vlan vlan-idtunnel-affinity num WSS# show fdb all WSS# show fdb Syntax show fdb agingtime vlan vlan-id Show fdb agingtimeOutput for show fdb WSS# show fdb agingtime See Also set fdb agingtime on Show fdb countShow roaming station See Also show fdb on Show roaming vlan Output for show roaming stationSee Also show roaming vlan on Syntax show roaming vlan WSS# show roaming vlan Output for show roaming vlan Show roaming station on Show vlan config onShow security l2-restrict Syntax show security l2-restrict vlan vlan-idall Show tunnel Enabled. Forwarding of Layer 2 traffic from clients isDisabled. Layer 2 forwarding is not restricted Output for show security l2-restrict Syntax show vlan config vlan-id Show vlan configSee Also show vlan config on Output for show tunnel Output for show vlan config See Also Vlan Commands NN47250-100 Version Quality of Service Commands Clear qos WSS# clear qos dscp-to-qos-map Set qos cos-to-dscp-mapWSS# clear qos Syntax set qos cos-to-dscp-map level dscp dscp-value Set qos dscp-to-cos-map Show qos Show qos dscp-table See Also show qos dscp-table onSee Also show qos on IP Services Commands Set ntp server on Set ntp update-interval onSet ntp on Show ntp on Clear interface Syntax clear interface vlan-idipWSS# clear interface mauve ip Clear ip alias Clear ip dns domain Syntax clear ip dns server ip-addr Clear ip dns serverClear ip route WSS# clear ip dns server Syntax clear ip telnet Clear ip telnetClear ntp server WSS# clear ip telnet success change accepted WSS# clear ntp update-interval success change accepted Clear ntp update-intervalSyntax clear ntp update-interval Clear snmp community Syntax clear snmp notify profile profile-name Clear snmp notify profileClear snmp notify target Syntax clear snmp notify target target-num Clear snmp usm Clear summertime Clear system ip-address Clear timezone Ping Host Count num-packetsCount-5 WSS# ping Set arpSee Also traceroute on Syntax set arp permanent static dynamic ip-addrmac-addr Syntax set arp agingtime seconds Set arp agingtimeSet interface WSS# set arp agingtime Enables the Dhcp client on the Vlan WSS# set interface default ip 10.10.10.10/24Syntax set interface vlan-idip dhcp-client enable disable Set interface dhcp-client Set interface dhcp-server WSS# set interface corpvlan ip dhcp-client enableDefault-router ip-addr Clear interface on Show dhcp-client on Show interface on Dns-domain Default-routerSet interface status Primary-dns and secondary-dns Set ip dns Syntax set ip dns enable disableSet ip alias Syntax set ip alias name ip-addr Syntax set ip dns domain name WSS# set ip dns enableSet ip dns domain WSS# set ip dns domain example.com Primary Set ip dns serverSyntax set ip dns server ip-addrprimary secondary Secondary Enable Enables the Https server Disable Syntax set ip https server enable disableWSS# set ip https server enable Set ip https server WSS# set ip route default 10.5.4.1 WSS# set ip route 192.168.4.0 255.255.255.0 10.5.4.2WSS# set ip route 192.168.5.0/24 10.5.5.2 Set ip snmp server Syntax set ip snmp server enable disableWSS# set ip snmp server enable Set ip ssh WSS# set ip ssh port Syntax set ip ssh server enable disableSet ip ssh server Crypto generate key on Set ip ssh on Set ip ssh server on Set ip telnet server Syntax set ip telnet server enable disableSet ip telnet Syntax set ip telnet port-num WSS# set ntp enable WSS# set ip telnet server enableSyntax set ntp enable disable Enable Enables the NTP client Disable Set ntp update-interval Set ntp server Set snmp community WSS# set snmp community name switchmgr1 notify-read-write Read-notify Notify-only Notify-read-writeWSS# set snmp community read-write goodcommunity Default profile-name Set snmp notify profileDrop send ClientAuthenticationFailureTraps-Generated AutoTuneRadioPowerChangeTraps-GeneratedClientAuthorizationSuccessTraps-Generated ApOperRadioStatusTraps-Generated when Cont RFDetectSpoofedSsidAPTraps-Generated when RFDetectUnAuthorizedSsidTraps-Generated See Also Show snmp notify profile on SNMPv3 with Informs Security unsecured authenticated encryptedSet snmp notify target Snmp-engine-id Retries num Security unsecured authenticated encryptedTimeout num SNMPv3 with Traps SNMPv2c with Informs Community-string Community string Profile profile-nameSNMPv2c with Traps WSS# set snmp notify target 2 10.10.40.10 v1 trap SNMPv1 with Traps Set snmp protocol Syntax set snmp protocol v1 v2c usm all enable disableWSS# set snmp protocol all enable V2c Set snmp security Set snmp usmWSS# set snmp security encrypted String Engine Snmp-engine-id ip ip-addr local hex hexSpecifies a unique identifier for the Snmp Allow get and set operations and so on Specifies the access level of the user Auth-pass-phrase string option Start Set summertimeWSS# set snmp usm snmpmgr1 snmp-engine-id local Second , third , fourth , or last 23x0# set summertime PDT success change accepted EndEnd of the time change period Dd-day Set timedateMmm-month Yyyy-year Set timezone Syntax set timezone zone-name -hours minutes23x0# set timezone PST Syntax show arp ip-addr Show arpOutput for show arp WSS# show arp Show dhcp-client Output for show dhcp-client WSS# show dhcp-client Syntax show dhcp-server interface vlan-id verbose Show dhcp-serverSee Also set interface dhcp-client on WSS# show dhcp-server Output for show dhcp-server Output for show dhcp-server verbose Syntax show interface vlan-id Show interfaceSee Also set interface dhcp-server on WSS# show interface Show ip alias Output for show interface Output for show ip dns Show ip dnsOutput for show ip alias Syntax show ip dns Show ip https Show ip httpsWSS show ip https Syntax show ip route destination Show ip routeOutput for show ip https Destination Output for show ip route Show ip telnet Show ip telnetWSS show ip telnet Syntax show ntp Show ntpOutput for show ip telnet WSS show ntp Output for show ntp Synced Show snmp community Show snmp countersShow snmp notify profile Syntax show snmp notify target Show snmp notify targetShow snmp status Syntax show snmp status Syntax show summertime Show snmp usmShow summertime 23x0# show summertime Show timedate Show timezone WSS# telnet TelnetSyntax telnet ip-addr hostname port port-num WSS-remote show vlan Traceroute WSS-remote Session 0 pty tty2.d terminated tt name tty2.d Error Messages for traceroute See Also ping onWSS# traceroute server1 AAA Commands Syntax clear accounting admin dot1x system user-wildcard Clear accounting WSS# clear accounting dot1x Nin Clear authentication adminSyntax clear authentication admin user-wildcard System Syntax clear authentication console user-wildcard Clear authentication consoleWSS# clear authentication admin Jose WSS# clear authentication console Regina WSS# clear authentication dot1x ssid finance *@thiscorp.com Clear authentication dot1xClear authentication last-resort Wired WSS# clear authentication mac ssid thatcorp aabbcc Clear authentication macClear authentication proxy WSS# clear authentication proxy ssid mycorp Clear location policy Clear authentication webSet authentication proxy on Show aaa on Syntax clear location policy rule-number WSS# clear location policy Clear mac-userClear mac-user attr Syntax clear mac-user mac-addr WSS# clear mac-user 010203040506 attr filter-id Clear mac-user groupSyntax clear mac-usermac-addr attr attribute-name Syntax clear mac-user mac-addrgroup Syntax clear mac-usergroup group-name Clear mac-usergroupClear mac-usergroup attr WSS# clear mac-usergroup eastcoasters Clear mobility-profile Clear user WSS# clear user Nin WSS# clear user Hosni attr session-timeoutClear user attr Syntax clear user username attr attribute-name Clear user group Clear usergroup Syntax clear usergroup group-name attr attribute-name Set accounting admin consoleClear usergroup attr WSS# clear usergroup cardiology attr time-of-day Start-stop Stop-only WSS# set accounting admin Natasha start-stop localSet accounting dot1x mac web last-resort Method1 Method2 Method3 Method4 Web Method1 method2 method3 method4Mac Ssid ssid-name Set accounting system WSS# set accounting dot1x Nin stop-only sg2WSS# set accounting system shorebirds Set authentication admin For more information, see Usage Set authentication console WSS# set authentication admin Jose sg3 User-wildcard Method1 Method2 Method3 Method4 Set authentication dot1x WSS# set authentication console * none Already been authenticated Or a period .. For details, see User Wildcards onBonded Protocol Method1 Method2 Method3 Method4 Sg1 sg2 sg3 success change accepted Set service-profileauth-fallthru on Show aaa on Set authentication last-resortSet authentication mac Wired Set authentication proxy WSS# set authentication ssid mycorp2 mac ** local Set authentication web WSS# set authentication proxy ssid mycorp ** srvrgrp1 WSS# set authentication web ssid ourcorp rnd* local Permit Set location policyDeny Optionally, you can add the suffix .out to the name Eq-Applies the location policy rule to all usernames Show location policy commandClear location policy rule-numbercommand Neq-Applies the location policy rule to all usernames WSS# set location policy permit vlan floor2 if port 3-7,12 Set mac-userWSS# set location policy deny if user eq *.theirfirm.com Clear location policy on Show location policy on Syntax set mac-user mac-addrgroup group-name WSS# set mac-user 010203040506 group eastcoastersClear mac-user on Show aaa on Set mac-user attr Syntax set mac-usermac-addr attr attribute-name value Authentication Attributes for Local Users Encryption-typeEnd-date Filter-id Mobility-profileMobility-profile on By the set dot1x reauth-period command is Service-typeSession-timeout Ssid Day wk0900-1700,sa2200-0200 Time-of-day1600,th1000-1600 With start-date,end-date, or both Url $u-Username $v-VLAN $s-SSID $p-Service profile nameWSS# set mac-user 010203040506 attr filter-id acl-03.in Vlan-name WSS# set mac-usergroup eastcoasters attr vlan-name orange For a list of authorization attributes, see onSet mac-usergroup attr Clear mac-user attr on Show aaa on Or wired authentication port on the WSS Ports and wired authentication port on the WSSSet mobility-profile WSS# set mobility-profile mode enable Set mobility-profile modeSyntax set mobility-profile mode enable disable WSS# set mobility-profile name magnolia port WSS# set user admin password chey3nne Syntax set user username password encrypted stringWSS# set user Nin password goody Set user WSS# set user Tamara attr vlan-name orange WSS# set user Nin password 29Jan04Set user attr WSS# set user Tamara attr mobility-profile tulip Syntax set user username group group-name Set user groupSet usergroup WSS# set user Hosni group cardiology Syntax set usergroup group-name attr attribute-name value Syntax set web-portal enable disableSet web-portal Clear usergroup on Clear usergroup attr on Show aaa on Show aaa Show aaa Output User Nin Show accounting statistics UP operating Syntax show accounting statistics WSS# show accounting statistics Show accounting statistics Output Radius serverLocal WSS database Show location policy Show mobility-profile AAA Commands NN47250-100 Version Syntax clear domain security Mobility Domain CommandsClear domain security 23x0# clear domain security Set domain security Clear mobility-domainClear mobility-domain member See Also set mobility-domain member on WSS# set domain security required Set mobility-domain memberSyntax set domain security none required Syntax set mobility-domain member ip-addrkey hex-bytes Clear mobility-domain on Show mobility-domain config on Set mobility-domain mode member seed-ipSet mobility-domain mode member secondary-seed- ip WSS# set mobility-domain member Set mobility-domain mode seed domain-name WSS# set mobility-domain mode member secondary-seed-ipClear mobility-domain member on Show mobility-domain on WSS# show mobility-domain config Show mobility-domain configSyntax show mobility-domain config Show mobility-domain Show mobility-domain Output Syntax show mobility-domainWSS# show mobility-domain Mobility Domain Commands NN47250-100 Version Syntax clear network-domain Network Domain CommandsClear network-domain 23x0# clear network-domain Clear network-domain peer Clear network-domain modeSyntax clear network-domain mode seed member Syntax clear network-domain peer ip-addrall Clear network-domain seed-ip Set network-domain mode member seed-ipSee Also set network-domain mode member seed-ip on See Also set network-domain peer on Syntax set network-domain peer ip-addr WSS# set network-domain mode member seed-ipSet network-domain peer Clear network-domain on Show network-domain on Set network domain peer command Set network-domain mode seed domain-nameWSS# set network-domain mode seed domain-name California Show network-domain WSS# show network-domain Show network-domain OutputSyntax show network-domain Output if WSS is the Network Domain seed Output if WSS is a Network Domain member Network Domain Commands NN47250-100 Version Set ap upgrade-firmware on AP CommandsSet ap radio mode on Set ap radio radio-profile on Set service-profilewpa-ie on Set service-profileweb-portal-acl onSet service-profileauth-psk on Set service-profilersn-ie on Set service-profile psk-phrase on Set service-profile cipher-wep104 onSet service-profile cipher-wep40 on Set service-profile psk-raw on Set radio-profileauto-tunepower-lockdown on Set radio-profileauto-tunepower-config onSet radio-profileauto-tunepower-interval on Set ap radio auto-tunemax-power on Clear ap image Syntax clear ap ap-numberimage WSS# clear ap 7 local-switching vlan-profile Clear ap local-switching vlan-profileSyntax clear ap ap-numberlocal-switching vlan-profile See Also set ap image on Syntax clear ap port-listap ap-numradio 1 2 all Clear ap radioRadio-Specific Parameters Radio Channel number for Country of operation 802.11b/g-6802.11a-Lowest valid Option dap removed for AP WSS# clear ap 1 boot-configuration Clear ap boot-configurationSyntax clear ap boot-configuration ap-num Clear ap radio load-balancing group Clear radio-profile Short-retry Clear service-profileLong-retry Countermeasures parameter added Soda success-page Soda failure-pageSoda remediation-acl Soda logout-page Option force-image-download added Reset apSet ap auto Option radio num auto-tune min-client-rate Configurable Profile Parameters for APs WSS# set ap auto WSS# set ap auto mode enable Set ap auto modeSyntax set ap auto mode enable disable Set ap auto persistent Syntax set ap auto persistent ap-numall Set ap auto radiotype11a-802.11a WSS# set ap auto persistent 10 success change accepted Set ap bias WSS# set ap auto radiotype 11bSyntax set ap port-listap ap-numauto bias high low Set ap blink See Also show ap config onSyntax set ap port-list ap ap-num auto blink enable disable WSS# set ap 1 bias low Mode enable disable Set ap boot-configuration ipWSS# set ap 3-4 blink enable Enables or disables the static IP address for the AP Set ap boot-configuration mesh mode Set ap boot-configuration mesh psk-phraseWSS# set ap 7 boot-configuration mesh mode enable Set ap boot-configuration mesh psk-raw Syntax set ap ap-numberboot-configuration mesh psk-raw hex Set ap boot-configuration mesh ssid WSS# set ap 7 boot-configuration mesh ssid wlan-mesh Set ap boot-configuration switch Switch-ip ip-addr Vlan-tag tag-value Set ap boot-configuration vlanEnables or disables use of the specified Vlan tag on the AP Vlan tag value. You can specify a number from Set ap force-image-download Set ap security on Show ap config on Show ap status onSet ap fingerprint Syntax set ap num fingerprint hex Syntax set ap port-list ap ap-num auto group name WSS# set ap 69 force-image-download enableSet ap group Auto on WSS# set ap 1,4,7 group loadbalance1 Show ap config on Show ap group onSet ap image WSS# set ap 4 group none Syntax set ap ap-numberlocal-switching mode enable disable Set ap local-switching modeSet ap local-switching vlan-profile WSS# set ap 7 local-switching mode enable WSS# set ap 7 local-switching vlan-profile locals Set ap nameSyntax set ap port-list ap ap-numname name WSS# set ap 22 radio 1 antenna-location outdoor Set ap radio antenna-locationWSS# set ap 1 name techpubs Indoors Set ap radio antennatype See Also set ap radio antennatype on Ap port-list Ap ap-num radio 1 radio Set ap radio auto-tune max-power Set ap radio auto-tune min-client-rate WSS# set ap 7 radio 1 auto-tune max-powerSet ap radio auto-tune max-retransmissions Deprecated in WSS Software Version Set ap radio channel WSS# set ap 11 radio 1 channel 1 tx-powerSet ap radio tx-power on Show ap config on WSS# set ap 5 radio 1 channel Set ap radio load-balancing Set ap radio min-tx-datarateSet ap radio link-calibration Ap ap-number Syntax set ap ap-numradio 1 2 load-balancing enable disable WSS# set ap 7 radio 1 load-balancing disableSet ap radio load-balancing group Set ap radio mode Syntax set ap port-listauto radio 1 2 mode enable disableWSS# set ap 7 radio 1 load-balancing group room1 Set ap radio radio-profile WSS# set ap 1-5 radio 1 mode enableWSS# set ap 1-3 radio 2 mode enable Radio-profile name Set ap radio tx-power WSS# set ap 5 radio 1 tx-power Set ap radio channel on Show ap config on Set ap security Syntax set ap security require optional noneWSS# set ap security none WSS# set ap 9 upgrade-firmware disable Set ap upgrade-firmwareSyntax set ap port-listauto upgrade-firmware enable disable Set ap sticky-bit Syntax set band-preference none 11bg 11a Set load-balancing modeSyntax set load-balancing mode enable disable WSS# set band-preference 11a Syntax set load-balancing strictness low med high max WSS# set load-balancing mode disableSet load-balancing strictness Max Set radio-profile active-scan Syntax set radio-profile name active-scan enable disableSet radio-profile 11g-only WSS# set load-balancing strictness max Set radio-profile auth-dot1x Set radio-profile auto-tune channel-configWSS# set radio-profile radprof3 active-scan disable Set radio-profile auth-psk WSS# set radio-profile rp2 auto-tune channel-config disable Set radio-profile auto-tune channel-holddownWSS# set radio-profile rp2 auto-tune channel-holddown Set radio-profile auto-tune channel-interval WSS# set radio-profile rp2 auto-tune channel-interval Set radio-profile auto-tune channel-lockdown Set radio-profile auto-tune power-backoff-timerSet radio-profile auto-tune power-config Syntax set radio-profile name auto-tune channel-lockdown Defaults The default power tuning interval is 300 seconds Set radio-profile auto-tune power-intervalWSS# set radio-profile rp2 auto-tune power-config enable Started Syntax set radio-profile name auto-tune power-lockdown Set radio-profile auto-tune power-lockdownWSS# set radio-profile rp2 auto-tune power-interval WSS# set radio-profile rp2 auto-tune power-lockdown Set radio-profile beacon-interval Set radio-profile auto-tune power-ramp-intervalWSS# set radio-profile rp2 auto-tune power-ramp-interval Syntax set radio-profile name beacon-interval interval Set radio-profile cipher-tkip Set radio-profile beaconed-ssidSet radio-profile cipher-ccmp Set radio-profile cipher-wep104 WSS# set radio-profile radprof3 countermeasures rogue ConfiguredSet radio-profile countermeasures Rogue Set radio-profile crypto-ssid Set radio-profile dtim-interval Set radio-profile frag-threshold Syntax set radio-profile name frag-threshold thresholdWSS# set radio-profile rp1 frag-threshold Set radio-profile long-retry Set radio-profile max-rx-lifetimeSet radio-profile max-tx-lifetime Syntax set radio-profile name mode enable disable Set radio-profile modeDefaults for Radio Profile Parameters WSS# set radio-profile rp1 max-tx-lifetime Wmm-powersave Disable Rfid-mode DisableService-profile Countermeasures Wmm-powersave 11g-onlyRfid-mode Set radio-profile psk-raw Set radio-profile preamble-lengthSet radio-profile psk-phrase Syntax set radio-profile name preamble-length long short Syntax set radio-profile name qos-mode svp wmm Set radio-profile qos-modeSet radio-profile rate-enforcement WSS# set radio-profile rp1 qos-mode svp Enables data rate enforcement for the radios in the radio Disables data rate enforcement for the radios in the radioSet radio-profile rfid-mode Set radio-profile rts-threshold Syntax set radio-profile name rfid-mode enable disableWSS# set radio-profile rfid-mode enable Syntax set radio-profile name rts-threshold threshold Set radio-profile service-profile Defaults for Service Profile ParametersSyntax set radio-profile name service-profile name Cipher-wep104 Disable Cipher-ccmp DisableCipher-tkip Enable Cipher-wep40 Disable Rsn-ie Disable No-broadcast DisableProxy-arp Disable Shared-key-auth Disable 2.0 12.0,24.0Auto 2.0,5.5,11.0 Wpa-ie Disable Portal-acl settingTimeout Web-portal-acl Portalacl WSS# set radio-profile rp2 service-profile wpaclients Set radio-profile tkip-mc-time Set radio-profile shared-key-authSet radio-profile short-retry Set radio-profile wep active-multicast-index WSS# set radio-profile rp1 wmm-powersave enable Set radio-profile wmm-powersaveSyntax set radio-profile name wmm-powersave enable disable See set service-profilewpa-ie on Set service-profile attr Syntax set service-profile name attr attribute-name valueWSS# set service-prof sp2 attr vlan-name blue Syntax set service-profile name auth-dot1x enable disable Set service-profile auth-dot1xWSS# set service-prof sp2 attr mobility-profile tulip WSS# set service-profile wpaclients auth-dot1x disable Set service-profile auth-fallthru Last-resortWeb-portal Syntax set service-profile name auth-psk enable disable Set service-profile auth-pskWSS# set service-profile rndlab auth-fallthru web-portal WSS# set service-profile wpaclients auth-psk enable Syntax set service-profile name beacon enable disable Set service-profile beaconSet service-profile bridging Mesh-service-profile Mesh service profile WSS# set service-profile sp1 cac-mode session Set service-profile cac-modeSyntax set service-profile name cac-mode none session Set service-profilecac-session on Show service-profile on Syntax set service-profile name cac-session max-sessions Set service-profile cac-sessionSet service-profile cipher-ccmp WSS# set service-profile sp1 cac-session Syntax set service-profile name cipher-tkip enable disable Set service-profile cipher-tkipWSS# set service-profile sp2 cipher-ccmp enable WSS# set service-profile sp2 cipher-tkip disable Set service-profile cipher-wep104 WSS# set service-profile sp2 cipher-wep104 enableEnables 104-bit WEP encryption for WPA clients Syntax set service-profile name cipher-wep40 enable disable Set service-profile cipher-wep40Set service-profile cos WSS# set service-profile sp2 cipher-wep40 enable WSS# set service-profile sp1 cos Set service-profile dhcp-restrictSyntax set service-profile name cos level WSS# set service-profile sp1 dhcp-restrict enable WSS# set service-profile sp1 idle-client-probing disable Set service-profile idle-client-probingSet service-profile keep-initial-vlan Enables keepalives Set service-profile load-balancing-exempt See Also show service-profile onWSS# set service-profile sp3 keep-initial-vlan enable Syntax set service-profile name long-retry-count threshold Set service-profile long-retry-countWSS# set service-profile sp3 load-balancing-exempt enable WSS# set service-profile sp1 long-retry-count Syntax set service-profile name mesh mode enable disable Set service-profile meshSet service-profile no-broadcast Enables mesh services for the service profile WSS# set service-profile sp1 no-broadcast enable Set service-profile proxy-arpSyntax set service-profile name no-broadcast enable disable Syntax set service-profile name proxy-arp enable disable Set service-profile psk-phrase WSS# set service-profile sp1 proxy-arp enableSyntax set service-profile name psk-phrase passphrase Set service-profile psk-raw Set service-profile rsn-ieSyntax set service-profile name psk-raw hex Set service-profile shared-key-auth Syntax set service-profile name rsn-ie enable disableWSS# set service-profile sprsn rsn-ie enable Syntax set service-profile name short-retry-count threshold Set service-profile short-retry-countWSS# set service-profile sp4 shared-key-auth enable WSS# set service-profile sp1 short-retry-count Set service-profile soda agent-directory Set service-profile soda enforce-checksNetwork Syntax set service-profile name soda failure-page Set service-profile soda failure-pageWSS# set service-profile sp1 enforce-checks disable Set service-profile soda mode on Show service-profile on Set service-profile soda logout-page Syntax set service-profile name soda logout-page Syntax set service-profile name soda mode enable disable Set service-profile soda modeWSS# set service-profile sp1 soda logout-page logout.html WSS# set service-profile sp1 soda mode enable Set service-profile soda remediation-acl Set service-profile soda success-pageSyntax set service-profile name soda success-page Set service-profile ssid-name WSS# set service-profile sp1 soda success-page success.htmlSyntax set service-profile name ssid-name ssid-name WSS# set service-profile clearwlan ssid-name guest Set service-profile ssid-typeSet service-profile static-cos Syntax set service-profile name ssid-type clear crypto WSS# set service-profile sp1 static-cos enable Set service-profile tkip-mc-timeSyntax set service-profile name static-cos enable disable Syntax set service-profile name tkip-mc-time wait-time Set service-profile transmit-rates WSS# set service-profile sp3 tkip-mc-time11g-1.0, 2.0, 5.5, 6.0, 9.0, 11.0, 12.0, 18.0 Beacon-rate rate Multicast-rateBeacon-rate Syntax set service-profile name user-idle-timeout seconds Set service-profile user-idle-timeoutSet service-profile web-portal-acl WSS# set service-profile sp1 user-idle-timeout WSS# set service-profile sp3 web-portal-acl creditsrvr Set service-profile web-portal-formSyntax set service-profile name web-portal-acl aclname Syntax set service-profile name web-portal-form url WSS# mkdir corpa WSS# dir corpa Set service-profile web-portal-session-timeout Set service-profile web-portal-logoutSet service-profile web-portal-logout logout-url WSS# set service-profile sp1 web-portal-logout mode enable Set service-profile wep active-multicast-index WSS# set service-profile sp1 web-portal-session-timeout Set service-profile wep active-unicast-index WSS# set service-profile sp2 wep active-multicast-indexWSS# set service-profile sp2 wep active-unicast-index Syntax set service-profile name wep key-index num key value Set service-profile wep key-indexSet service-profile wpa-ie WSS# set service-profile sp2 wep key-index 1 key aabbccddee Syntax show ap arp ap-number WSS# set service-profile sp2 wpa-ie enableShow ap arp WSS# show ap arp Set ap local-switching mode on Set vlan-profile Show ap configSyntax show ap config port-listradio 1 Output for show ap arp WSS# show ap config Output for show ap config 802.11a 802.11b802.11g Syntax show ap counters port-listradio 1 Show ap unconfigured on Show radio-profile onShow ap counters WSS# show ap counters Output for show ap counters Use the show sessions network session-id session-idcommand Output for show ap counters Show ap dual-home See Also show sessions network on Syntax show ap fdb ap-number Show ap fdbOutput for show ap fdb WSS# show ap fdb Show ap qos-stats WSS# show ap qos-statsClears the counters after displaying their current values Syntax show ap etherstats port-listap-num Show ap etherstatsOutput for show ap qos-stats WSS# show ap etherstats Output for show ap etherstats Syntax show ap mesh-links ap-number Show ap groupShow ap mesh-links WSS# show ap mesh-links Syntax show ap status terse port-listall radio 1 Show ap statusOutput for show ap mesh-links Terse Power settings that are configured by RF Auto Radio state information, to indicate when anConfigured antenna model number Tuning WSS# show ap status terse Output for show ap status Image downloading-The AP is receiving a boot But has not yet begun bootingBooting-The AP has asked the WSS for a boot Image downloaded-The AP has received a boot Protection mode remains in effect until Configure succeed state indicates that the APHas received configuration parameters for Sweep Mode indicates that a disabled radio is Indicates that an external antenna was detected But no external antenna is configured onAntenna is configured on the radio but no Radio Show ap vlan Output for show ap status terse and show ap status terse Syntax show ap vlan ap-number Set vlan-profile Set ap local-switching mode onOutput for show ap vlan WSS# show ap vlan Syntax show auto-tune attributes ap ap-numradio 1 2all Show auto-tune attributesOutput for show auto-tune attributes WSS# show auto-tune attributes ap 2 radio Set radio-profileauto-tunepower-backoff-timer on Show auto-tune neighborsSyntax show auto-tune neighbors ap ap-numradio 1 2all Output for show auto-tune neighbors Rssi Syntax show ap boot-configuration ap-num Show ap boot-configurationOutput for show ap boot-configuration WSS# show ap boot-configuration Connection Show ap connectionSyntax show ap connection ap-numserial-id serial-ID Serial-id serial-ID WSS# show ap connection Total number of entries Show ap config on Show ap global on Show ap unconfigured onOutput for show ap connection WSS# show ap connection serial-id Syntax show ap global ap-numserial-id serial-ID Show ap globalOutput for show ap global WSS# show ap global Show ap unconfigured Syntax show ap unconfiguredWSS# show ap unconfigured Show load-balancing group Output for show ap unconfiguredThis WSS switch as a member Show ap connection on Show ap global on WSS# show load-balancing group blue Show radio-profileOutput for show load-balancing group Syntax show radio-profile name ? WSS# show radio-profile default Output for show radio-profile Svp-AP forwarding queues are optimized for Wmm-AP forwarding queues provide standardPriority handling for WMM devices SpectraLink Voice Priority SVP Show service-profile Syntax show service-profile name ? Profile output Clear-Wireless traffic for the Ssid is Output for show service-profileCrypto-Wireless traffic for the Ssid is Unencrypted User, without requiring a username and password Last-resort-Automatically authenticates the userAllows access to the Ssid requested by None-Denies authentication and prohibits Preset-The key is configured None-CAC is disabledNone-The key is not configured Session-CAC is based on the number of active 802.1X-dynamic authentication Radios in the radio profile mapped to this serviceAuthentication-Lists the authentication methods PSK-preshared key authentication FieldDescription AP Commands AP Commands NN47250-100 Version STP Commands Set spantree uplinkfast onShow spantree uplinkfast on Clear spantree portcost Clear spantree portpri Resets the cost for all VLANs Clear spantree portvlancostClear spantree portvlanpri Syntax clear spantree statistics port-listvlan vlan-id Clear spantree statisticsSyntax clear spantree portvlanpri port-listall vlan vlan-id WSS# clear spantree statistics 5,11,19-22 See Also show spantree statistics on Set spantreeSet spantree backbonefast See Also show spantree on Set spantree fwddelay Set spantree helloSee Also show spantree backbonefast on Set spantree maxage Set spantree portcost Set spantree portfast Snmp Port Path Cost DefaultsSyntax set spantree portfast port port-listenable disable WSS# set spantree portcost 3,4 cost Set spantree portpri Set spantree portvlancostSee Also show spantree portfast on Cost cost All Set spantree portvlanpriWSS# set spantree portvlancost 3,4 cost 20 vlan mauve Priority value All Set spantree priority Set spantree uplinkfast Show spantree WSS# set spantree uplinkfast enableWSS# show spantree vlan default See Also show spantree uplinkfast on Bridge Max Age 20 sec Hello Time 2 sec Forward Delay 15 sec Output for show spantree Show spantree backbonefast See Also show spantree blockedports onSyntax show spantree backbonefast See Also set spantree backbonefast on WSS# show spantree blockedports vlan defaultShow spantree blockedports WSS# show spantree backbonefast WSS# show spantree portfast Show spantree portfastSyntax show spantree portfast port-list Uplink fast convergence information for all ports See Also set spantree portfast on Show spantree portvlancostOutput for show spantree portfast Syntax show spantree portvlancost port-list WSS# show spantree statistics Show spantree statisticsSyntax show spantree statistics port-listvlan vlan-id Statistics for all ports Inactive Output for show spantree statistics Output for show spantree statistics Output for show spantree statistics See Also clear spantree statistics on Show spantree uplinkfastOutput for show spantree uplinkfast Syntax show spantree uplinkfast vlan vlan-id See Also set spantree uplinkfast on STP Commands NN47250-100 Version Syntax clear igmp statistics vlan vlan-id Igmp Snooping CommandsClear igmp statistics Statistics Show igmp statistics on Clear igmp statistics on See Also show igmp statistics on Set igmpSet igmp lmqi See Also show igmp on Set igmp mrouter Set igmp mrsolSee Also show igmp mrouter on See Also set igmp mrsol mrsi on Set igmp mrsol mrsiSet igmp oqi See Also set igmp mrsol on WSS# set igmp oqi 200 vlan orange Syntax set igmp proxy-report enable disable vlan vlan-idSet igmp proxy-report Vlan vlan-id Set igmp qri WSS# set igmp proxy-report disable vlan orangeSet igmp qi Syntax set igmp qi seconds vlan vlan-id Syntax set igmp qri tenth-seconds vlan vlan-id Syntax set igmp querier enable disable vlan vlan-idSet igmp querier WSS# set igmp qri 50 vlan orange See Also show igmp querier on Set igmp receiverSet igmp rv See Also show igmp receiver-table on Syntax show igmp vlan vlan-id Show igmpWSS# set igmp rv 4 vlan orange WSS# show igmp vlan orange Output for show igmp Dvmrp PIM Madv-Multicast advertisement Conf Static multicast port configured by anAdministrator Quer-IGMP query Show igmp mrouter Syntax show igmp mrouter vlan vlan-idWSS# show igmp mrouter vlan orange Syntax show igmp querier vlan vlan-id Show igmp querierOutput for show igmp mrouter Set igmp mrouter on Show igmp mrouter on WSS# show igmp querier vlan orange Output for show igmp querier WSS# show igmp querier vlan defaultShow igmp receiver-table See Also set igmp querier on WSS Software displays the multicast receivers on all WSS# show igmp receiver-table vlan orangeWSS# show igmp receiver-table group 237.255.255.0/24 VLANs See Also set igmp receiver on Show igmp statisticsOutput for show igmp receiver-table Syntax show igmp statistics vlan vlan-id Output for show igmp statistics See Also clear igmp statistics on Igmp Snooping Commands NN47250-100 Version Clear sessions Session Management CommandsWSS# clear sessions admin WSS# clear sessions console WSS# clear sessions telnet client Clear sessions networkSee Also show sessions on WSS# clear sessions network mac-addr Show sessions Console Telnet See Also clear sessions on Show sessions networkShow sessions telnet client Output Mac-addr mac-addr Verbose output Session-id output WSS show sessions network user E WSS show sessions networkWSS show sessions network mac-addr 00055d7e981a WSS show sessions network verbose Show sessions network summary Output WSS# show sessions network session-id Additional show sessions network verbose Description Amount of time the session has been on this AP IP address and port number of the WSS managing the APSerial number and radio number of the AP AAA-VLAN is from Radius or the local database Show sessions network session-id Output DOT1X See Also clear sessions network on Session Management Commands NN47250-100 Version Syntax clear security acl acl-name all editbuffer-index Security ACL CommandsClear security acl Clears all security ACLs Set security acl ip acl134 hits #3 WSS# show security acl info allSet security acl ip acl133 hits #1 Set security acl ip acl135 hits #2 Clear security acl map WSS# clear security acl map acljoe port 4Out Syntax commit security acl acl-nameall Commit security aclWSS# clear security acl map all Type Class Mapping See Also show security acl on Hit-sample-rateRollback security acl Syntax rollback security acl acl-nameall Set security acl By UDP packets Any Priority precedence Minimum delayRoutine precedence Immediate precedence WSS# set security acl ip acl123 deny 192.168.2.11 WSS# commit security acl all WSS port or ports Set security acl mapWSS set security acl map acl133 port 4 Tag tag-list Syntax set security acl hit-sample-rate seconds Configuration fileSet security acl hit-sample-rate Set security acl ip acl153 hits #3 WSS# show security acl hits Show security aclShow security acl dscp Index Counter ACL-name Syntax show security acl info all editbuffer Show security acl editbufferShow security acl hits WSS# show security acl editbuffer Syntax show security acl info acl-nameall editbuffer Show security acl infoSyntax show security acl hits WSS# show security acl info Show security acl map Show security acl resource-usage Show security acl resource-usage Output True-Security ACLs are mapped True-A default action types is definedFalse-No default action type is defined False-No security ACLs are mapped True-Security ACLs are mapped to incoming traffic False-No security ACLs are mapped to incoming Cryptography Commands PEM-formatted Crypto ca-certificateEap Certificate WSS# crypto certificate admin Crypto certificateSee Also show crypto ca-certificate on Domain Crypto generate keyCrypto generate request on Crypto generate self-signed on Ssh Crypto generate request WSS# crypto generate key adminSyntax crypto generate request admin eap web See Also show crypto key ssh on Webaaa option renamed to web WSS# crypto generate request adminEmail Address admin@example.com Maximum string length for State Name increased Syntax crypto generate self-signed admin eap web Crypto generate self-signedCrypto certificate on Crypto generate key on WSS# crypto generate self-signed admin Syntax crypto otp admin eap web one-time-passwordCrypto otp See Also crypto pkcs12 on Syntax crypto pkcs12 admin eap web file-location-urlCrypto pkcs12 WSS# crypto generate otp eap hap9iN#ss WSS# crypto otp eap hap9iN#ss See Also crypto otp onWSS# copy tftp//192.168.253.1/2048full.p12 2048full.p12 WSS# crypto pkcs12 eap 2048full.p12 Show crypto ca-certificate Output Syntax show crypto ca-certificate admin eap webShow crypto ca-certificate WSS# show crypto ca-certificate Crypto certificate Output Syntax show crypto certificate admin eap webShow crypto certificate WSS# show crypto certificate eap Show crypto key domain Show crypto key sshSee Also crypto generate key on Cryptography Commands NN47250-100 Version Clear radius Radius and Server Groups CommandsSyntax clear radius deadtime key retransmit timeout Clear server group on Clear radius client system-ip See Also set radius proxy client on Clear radius proxy clientClear radius proxy port See Also set radius proxy port on Clear radius server Clear server group Set radius See Also set server group on Set radius client system-ip Syntax set radius proxy client address ip-address Set radius proxy clientSet radius proxy port WSS# set radius proxy client address 10.20.20.9 key radkey1 Set radius server WSS# set radius proxy port 3-4 tag 104 ssid mycorpSsid ssid-name Ssid supported by the third-party AP Encrypted-key-No key Author-password-nortel Set server group Members server Set server group load-balance 23x0# set server group shorebirds load-balance enable23x0# set server group shorebirds load-balance disable Group-name Server group name of up to 32 characters Radius and Server Groups Commands NN47250-100 Version 802.1X Management Commands Syntax clear dot1x max-req Clear dot1x bonded-periodClear dot1x max-req WSS# clear dot1x bonded-period Clear dot1x port-control Clear dot1x quiet-periodClear dot1x reauth-max Clear dot1x timeout auth-server Clear dot1x reauth-period Clear dot1x timeout supplicant Clear dot1x tx-period Set dot1x authcontrol Syntax set dot1x authcontrol enable disableWSS# set dot1x authcontrol enable Set dot1x bonded-period Set dot1x key-tx Set dot1x max-reqSee Also show dot1x on Set dot1x port-control WSS# set dot1x max-reqWSS# set dot1x port-control forceauth Set dot1x quiet-period Set dot1x reauth Set dot1x reauth-max Set dot1x reauth-period Set dot1x timeout auth-server Set dot1x timeout supplicant Set dot1x wep-rekey Syntax set dot1X wep-rekey enable disableSet dot1x tx-period Syntax set dot1x tx-period seconds Set dot1x wep-rekey-period Show dot1x WSS# show dot1x config WSS# show dot1x clients Show dot1x stats Output WSS # show dot1x stats 520 802.1X Management Commands Show rfdetect data on RF Detection CommandsRogue Information Show rfdetect clients on Show rfdetect visible on Syntax clear rfdetect attack-list mac-addr Clear rfdetect attack-listClear rfdetect black-list Syntax clear rfdetect black-list mac-addr Clear rfdetect ignore Clear rfdetect ssid-list Syntax clear rfdetect vendor-list client ap mac-addrall Clear rfdetect vendor-listSet rfdetect attack-list WSS# clear rfdetect vendor-list client aabbcc000000 Set rfdetect black-list Set rfdetect ignore Set rfdetect log Syntax set rfdetect log enable disable23x0# set rfdetect log enable 23x0# set rfdetect ignore aabbcc112233 Set rfdetect signature Set rfdetect ssid-listSee Also show log buffer on Syntax set rfdetect vendor-list client ap mac-addr Set rfdetect vendor-listWSS# set rfdetect ssid-list mycorp WSS# set rfdetect vendor-list client aabbcc000000 Show rfdetect attack-list Show rfdetect black-list Syntax show rfdetect clients mac mac-addr Show rfdetect clientsShow rfdetect clients Output WSS# show rfdetect clients mac 000c4163fd6d Show rfdetect clients mac Output Show rfdetect countermeasures Syntax show rfdetect countermeasuresWSS# show rfdetect countermeasures See Also set radio-profile countermeasures on Show rfdetect countersShow rfdetect countermeasures Output Syntax show rfdetect counters Show rfdetect data Syntax show rfdetect data Show rfdetect data Output Syntax show rfdetect ignore Show rfdetect ignoreShow rfdetect mobility-domain WSS# show rfdetect ignore Total number of entries WSS# show rfdetect mobility-domain Bssid and ssid options addedVendor, Type, and Flags fields added WSS# show rfdetect mobility-domain ssid nrtl-webaaa Show rfdetect mobility-domain Output Show rfdetect mobility-domain ssid or bssid Output Show rfdetect ssid-list Syntax show rfdetect vendor-list Show rfdetect vendor-listShow rfdetect visible WSS# show rfdetect vendor-list Shows neighbor information for radio Show ap status commandMac-addr Base MAC address of the Nortel radio Version Vendor, Type, and Flags fields added Syntax rfping mac mac-addrsession-id session-id RfpingShow rfdetect visible Output Show rfdetect data on Show rfdetect mobility-domain on Rfping Output WSS# rfping mac 000e9bbfad13 File Management Commands Backup Dir on Restore on Syntax backup system tftp/ip-addr/filenameall criticalWSS# backup system tftp/10.10.20.9/sysabak critical Tftp/ip-addr / filename Clear boot backup-configuration Clear boot configCopy Destination-url Syntax copy source-url destination-urlSource-url Be one of the following WSS# copy floorwss tftp//10.1.1.1/floorwss WSS# copy tftp//10.1.1.107/WSS020101.020 boot1WSS020101.020Delete WSS# copy tftp//10.1.1.1/closetwss closetwss Syntax dir subdirname file core boot0 boot1 WSS# copy testconfig tftp//10.1.1.1/testconfigWSS# delete testconfig Dir WSS# dir WSS# dir oldWSS# dir file Output for dir Install soda agentWSS# dir boot0 WSS# dir core Syntax load config url Load configWSS# install soda agent soda.ZIP agent-directory sp1 Uninstall soda agent on Set service-profile soda mode on Syntax md5 boot0 boot1filename WSS# load configWSS# load config testconfig1 Save config on Show boot on Show config on Syntax mkdir subdirname Pubs# md5 boot0WSS040003.020Mkdir WSS# mkdir corp2 Reset system Syntax reset system forceWSS# reset system Restore Save config See Also backup onRmdir WSS# save config testconfig1 Set boot backup-configurationSyntax save config filename Syntax set boot backup-configuration filename Set boot configuration-file Set boot partition Show boot New fields, Configured boot version and BackupBoot configuration, added Output for show boot Configuration area. You can specify one of the following Show configSyntax show config area area all Area area Show version New options added for remote traffic monitoring snoopRfdevice changed to rfdetect WSS# show version details Syntax uninstall soda agent agent-directory directory Uninstall soda agentSee Also show boot on WSS# uninstall soda agent agent-directory sp1 Install soda agent on Set service-profile soda mode on File Management Commands NN47250-100 Version Syntax clear log trace Trace CommandsClear log trace WSS# clear log trace Clear trace Save trace WSS# set trace authentication user jose Set trace authenticationSet trace authorization WSS# save trace traces/trace1 Level 5 is the default Set trace dot1xUser-readable information. If you do not specify a level Set trace sm WSS# set trace sm mac-addr Show trace Syntax show trace allWSS# show trace Syntax clear snoop filter-name Snoop CommandsClear snoop WSS# clear snoop snoop1 WSS# clear snoop map all Clear snoop mapWSS# clear snoop map snoop2 ap 3 radio Examples clear snoop map filter-nameap ap-numradio 1 Set snoop Set snoop map WSS# set snoop snoop1 observer 10.10.30.2 snap-lengthExamples set snoop map filter-nameap ap-numradio 1 WSS# set snoop map snoop1 ap 3 radio Set snoop modeEnable Stop-after num-pkts Filter. See show snoop stats on Syntax show snoop WSS# set snoop snoop1 mode enable stop-afterShow snoop WSS# show snoop Show snoop info Show snoop map Show snoop stats Clear snoop map on Set snoop map on Show snoop onExamples show snoop stats filter-nameap-numradio 1 Show snoop stats Output Snoop Commands NN47250-100 Version Syntax clear log buffer server ip-addr System Log CommandsClear log WSS# clear log server Logging state enabled or disabled Set logSeverity Defaults Set log mark See Also show log config on Set log trace mbytesShow log buffer Problems have occurred. These are logged for Reboot or shut downError-The WSS is missing data or is unable to Diagnostic purposes. No action is required WSS# show log config Show log configSyntax show log config Show log trace Positive number for example, +100, displays that Conditions are not resolved, the WSS can rebootError-The WSS is missing data or is unable to form Number of log entries starting from the oldest WSS# show log trace facility ? WSS# show log trace +5 facility Rogue System Log Commands NN47250-100 Version Boot Prompt Commands Syntax autoboot on on OFF off AutobootSee Also boot on Boot autoboot Boot Boot boot FN=WSS010101.020 DEV=boot1 ChangeChange on Show on Boot change Boot on Create on Delete on Dhcp on Next on Show on Boot create CreateChange on Delete on Next on Show on Dhcp Boot deleteBoot dhcp Syntax dhcp on on OFF off Diag Syntax dir c d e f boot0 boot1Boot dir Fver on Version on Syntax help command-name Syntax fver c d e f boot0 boot1 filenameBoot fver boot1 Fver Boot help fver See Also ls on Next ResetBoot next See Also help on Boot reset Show Output for show Compact flash. Boots using nonvolatileBoot show Storage or a flash card Primary partition of the flash card in the flash Nonvolatile storage area containing bootPartition Secondary partition of the flash card Test Boot versionEnables the poweron test flag Version Dir on Fver on Command Index Numerics NN47250-100 320658-G Version Delete 539 Command Index 282 340 Command Index Command Index MAC addresses 12 in user globs Vlan globs Command Index NN47250-100 320658-G Version Page Nortel WLAN-Security Switch 2300 Series Release

Nortel Networks 2300 Series manual Show system, See Also show system on, Syntax show system

Models: 2300 Series

See Also show system on page 68

show system

Syntax show system

show license command.

WSS# show system

WSS

NN47250-100 (Version 02.51)