VRF Configuration Tab | Cisco Systems 12000/10700 V3.1.1 specs

Chapter 16 MPLS VRF Management

Creating and Configuring the VRF Policy on a Device

Step 4 Choose Delete (located in the Routing Target area) to delete the routing target from the selected chassis. An Action Report window appears only if the delete action fails.

Step 5 Choose the Save icon on the toolbar to save your changes.

VRF Configuration Window—Detailed Description

Note You can only configure the attributes in the VRF Configuration window when the VRF is not present (uploaded) in to the chassis.

The VRF Configuration window (see Figure 16-9) displays the VRF Configuration tab.

VRF Configuration Tab

The VRF Configuration tab displays the following areas: VPN Details, Routing Destination, Threshold, Maximum Routes, Device Actions, Export, Import and Routing Target.

VPN Details

The VPN Details area displays the following information:

VPN—Allows you to configure the VPN ID for the selected VRF (as specified in RFC2685).

Routing Destination

The Routing Destination area displays the following information:

Routing Destination Id—Allows you to specify a route distinguisher to create routing and forwarding tables to uniquely identify the customer address though the customer site is not globally unique.

Threshold

The Threshold area displays the following information:

Illegal RX Threshold—Allows you to set the threshold on the number of illegally received labels above which the notification needs to be issued.

Maximum Routes

The Maximum Routes area displays the following information:

Maximum Routes—Allows you to configure the maximum number of routes allowed in this routing table.

Threshold in%—Allows you to configure the threshold value (in percentage of number of entries in routing table) at which to generate a warning message).

		Cisco 12000/10700 v3.1.1 Router Manager User Guide
		Cisco 12000/10700 v3.1.1 Router Manager User Guide
	OL-4455-01			16-11
	OL-4455-01			16-11

Image 513

Cisco Systems 12000/10700 V3.1.1 manual VRF Configuration Window-Detailed Description, VRF Configuration Tab

Contents

Corporate Headquarters Cisco 12000/10700 v3.1.1 Router Manager User Guide Cisco 12000/10700 v3.1.1 Router Manager User Guide Iii N T E N T S Views Object States Chassis Fault Management Window-Detailed Description Vii RPR Status Viewing the RPR Status Window Viii Module Performance Window-Detailed Description Interface Configuration SRP Interface Side Configuration Sonet Interface Status Xii Virtual Tributary Tab Xiii CAR Policy Configuration Deleting an Existing ToFab policy Xiv OAM tab Xvi Configuration Tab Xvii BGP-Details14-21 Xviii Redistribute Information Xix Mpls Interface Status Interface VRF Status Xxi Mpls Trap Management Xxii Archiving Xxiii Running Configs C-4 CE1 C-4 PE1 C-5 PE2 C-11 CE2 C-12 Xxiv Xxv Document Audience Chapter Number Chapter Title Content Document OrganizationXxvi Xxvii Managing VLANs Conventions Command ConventionsExample Conventions Format Description Example Document Conventions Obtaining DocumentationCisco.com Xxix Ordering Documentation Documentation CD-ROMDocumentation Feedback Xxx Obtaining Technical Assistance Technical Assistance CenterXxxi Cisco TAC Website Obtaining Additional Publications and InformationCisco TAC Escalation Center Xxxii Xxxiii Xxxiv A P T E R Overview Cisco Element Manager Framework Cisco EMF Software Cisco 12000/10720 Router Manager Software Overview Accessing Online Help Concepts See Physical Interfaces and Technologies section on Physical Objects Cisco 12000/10720 Router Chassis Cisco 12016 Chassis Supporting Modules LinecardsPhysical Interfaces and Technologies POS Logical Objects Use of Telecom Graphics Objects Logical Object Management FunctionsLogical Object Management Functions You Can Perform Sample Telecom Graphical Object Sample Cisco 12000 Chassis Showing Telecom Graphical Objects OSI Mappings Component Managed View Views Network View Layer 3 QoS ViewPhysical View Vlan View Cisco 12000/10720 Router Manager Object States Cisco 12000/10720 Router Manager Object States Decommissioned State ErroredNormal State Performance Logging On Discovery Lost Comms Lost CommsMismatched Transient Object States OL-4455-01 Cisco 12000/10720 Router Manager Workflow Getting Started ATM Starting a Cisco EMF User Session Starting Cisco EMF and Cisco 12000/10720 Router Manager Login window see -2 appears Launching an Application Launchpad Map Viewer Viewer AccessGroups Event Browser Events Notification Profiles Thresholding RegimesEvent Groups Deployment Quitting a Cisco EMF User SessionPreFilter Deployment Process Outline Deployment Process Workflow Manually Deploying a Generic Site Object Choose DeploymentDeploy Generic Objects Deployment Wizard Templates Window Deployment Wizard Object Parameters Window 1 Deployment Wizard Object Parameters Window 2 Deployment Wizard Views window appears Object Selector Window appears 11 Deployment Wizard-Views Window 12 Deployment Wizard-Summary Window IP Auto Discovery of the Cisco Chassis 14 Example of Auto Discovery Manually Deploying a Cisco 12000/10720 Chassis 15 Deployment Wizard-Object Parameters 1 16 Deployment Wizard-Object Parameters Window 3 Click on Select. The Object Selector window appears 18 Object Selector Window 20 Deployment Wizard Summary 21 Before Subchassis Discovery Commissioning and Subchassis Discovery Commissioning a Chassis 22 Chassis Configuration Window 23 After Subchassis Discovery Manually Deploying Modules Decommissioning a ChassisObject States Manually Deploying a GRP Card User Named vs. Auto Named Module Deployment 24 Deployment Wizard-Templates 25 Deployment Wizard-Object Parameters Click Select. The Object Selector window appears 27 Object Selector Window 28 Deployment Wizard-Views 29 Deployment Wizard-Summary Manually Deploying Line Cards Line Cards Supported by Cisco 12000 Series RoutersCard Type Menu Option Card Description SR-SC LR-SC Ethernet Line Cards Supported by Cisco 12000 Series Routers Menu Option Card Description Cisco 12000/10720 Router Manager POS LR2 Line Cards Supported by Cisco 10720 Routers 30 Deployment Wizard-Templates 31 Deployment Wizard-Object Parameters 32 Deployment Wizard-Views 33 Object Selector Window 34 Deployment Wizard-Views Deployment Wizard-Summary window appears Manually Deploying Supporting Modules Deploying a Clock Scheduler CardCard Card Type Card Description 36 Deployment Wizard-Views 37 Object Selector Window 38 Deployment Wizard-Views 39 Deployment Wizard-Summary 40 Deployment Wizard-Views Deploying a Switch Fabric Card 41 Object Selector Window 42 Deployment Wizard-Views 43 Deployment Wizard-Summary Pre-deployment Performing Pre-deployment OL-4455-01 Managing Chassis Launching the Chassis Management Windows Menu Options to Select to Open WindowManager Window/Task Viewing the Management Information Window Management Information Management Information Window-Configuration Tab System Configuration Choose the IOS/Command Line Security tab Entering or Changing IOS CLI Username and Passwords IOS/Command Line Security Tab Configuration TabSystem Configuration IOS Username and Passwords Viewing the Chassis Configuration Window Chassis Configuration Decommissioning a Chassis Commissioning a Chassis Action Report Window Starting Global Performance Logging Stopping Global Performance Logging Choose the Additional Descriptions tab Entering Additional Descriptions for a Selected Chassis Choose the Device Management tab Device Management Tab in Configuration Window Chassis Configuration Window-Detailed Description Additional Descriptions Tab Snmp ManagementDevice Management Tab Commission Status Modifying Snmp Community Names or Version Viewing the Snmp Management Window Enabling or Disabling Trap Generation Snmp Management Window-Detailed DescriptionCommunity Names Viewing the Chassis Inventory Window Chassis InventoryVersion Trap Generation General Tab Chassis Inventory Window-Detailed Description Asset Tracking Tab Viewing the Chassis Fault Management Window Chassis Fault Management 10 Chassis Fault Management Window-General Tab 11 Chassis Fault Management Window-Power Supply Tab 12 Chassis Fault Management Window-Temperature Tab Changing Column Width 13 Chassis Fault Management Window-Fan Tab Power Supply Tab Chassis Fault Management Window-Detailed DescriptionChassis Availability LED Status Temperature Temperature TabFan Tab Voltage Viewing the Command Log Window Command Log Command Log Window-Detailed Description Command Log Details TabCommand Log Details Table System Log Viewing the SysLog Messages WindowEvent History Details SysLog Message Tab System Log Window-Detailed Description Using RME for Chassis Management Tasks SysLog Messages AreaSys Log Message Details IOS Image Download Using RME Configuration Backup/Restore Using RMEAPS Status Viewing the APS Status Window 16 APS Status Window Initiating a Telnet Service APS Status Window-Detailed DescriptionAPS Circuits Area Configuration Editor Viewing the Configuration Editor WindowLaunching the Web Console 18 Configuration Editor Window Searching in the Configuration Editor Configuration Editor Window-Detailed DescriptionConfiguration Editor Tab Selection Viewing the RPR Configuration Window RPR ConfigurationOperations on Device Operations Done Locally 19 RPR Configuration Window RPR Configuration Window-Detailed Description Switch Over Tab RPR StatusViewing the RPR Status Window RP Status RPR Status Window-Detailed Description IP Routing Status Viewing the IP Routing Status windowLC Status IP Routing Status Window-Detailed Description Classless Inter-Domain Routing TabCidr Info TCP Status 22 TCP Status Window Viewing the TCP Status Window TCP Status Window-Detailed Description TCP Status TabTCP Status Connections Table TCP Connections Tab Viewing the UDP Status Window UDP Status Status UDP Status Window-Detailed Description UDP Port Information Module Abbreviation Cisco 12000/10720 Router Manager Module Names Cisco 12000/10720 Router Launching the Module Management Windows Viewing the Configuration Window Module Configuration Commissioning a Selected Module Configuration Window Decommissioning a Selected Module To decommission a module, proceed as follows Module Fault Management Module Configuration Window-Detailed DescriptionViewing the Module Fault Management Window Module Availability Module Fault Management Window-Detailed Description Cisco Contact Details Module Performance Starting or Stopping Performance Logging Viewing the Module Performance Window Module Performance Window-Detailed Description CPU UsagePerformance Logging Viewing the Module Inventory Window Module Inventory Module Inventory Window-Detailed Description GeneralModule Details Slot & Ports Asset Tracking Managing Interfaces Interface Interface Profiles Launching the Interface Profile Windows Interface Profile Types Creating an ATM Interface Profile Not applicable for Cisco 12000/10720 Router Manager Prompt Window Deleting an Existing ATM Interface Profile Editing an Existing ATM Interface Profile ATM Configuration Configuration 1 Tab Ilmi Configuration Configuration 2 TabInformation Element Layer Physical Layer Hsrp Profile Window Creating an Hsrp Profile Editing an Existing Hsrp Interface Profile Deleting an Existing Hsrp Interface Profile Hsrp Profile Window-Detailed DescriptionHsrp Profile Parameters Area Actions Creating a POS Interface Profile POS Profile Dialog -POS Config Tab Editing an Existing POS Interface Profile Deleting an Existing POS Interface Profile POS Config TabPOS Profile Window-Detailed Description General Alarm Reporting & Threshold Alarm ReportingSonet Overhead 11 SRP Side Profile Window Creating a SRP Side Profile 12 SRP Side Profile Window-Alarms tab Deleting an Existing SRP Side Profile Editing an Existing SRP Side Profile 14 Deletion Prompt Window SRP Side Profile Window-Detailed Description Alarms Tab Create ProfileReporting and Threshold Reporting Interfaces and Related Technology-Specific Windows Interface Configuration Interfaces Launching the Interface Configuration Windows Generic Interface Configuration Configuring and Commissioning a Generic Interface Viewing the Generic Interface Configuration Window Generic Interface Configuration Window-Detailed Description Configurable ParametersDecommissioning an Interface Viewing the ATM Interface Configuration Window ATM Interface Configuration ATM Interface Configuration Window-Configuration 1 Tab Configuring an ATM Interface ATM Interface Configuration Window-Detailed Description Ethernet Interface Configuration Ethernet Interface Configuration Window-Configuration Tab Viewing the Ethernet Interface Configuration Window Ethernet Interface Configuration Window-HSRP Parameters Tab Configuring an Ethernet Interface Hsrp Parameters Tab Ethernet Interface Configuration Window-Detailed Description Hsrp Parameters IP Configuration Configuring an IP Interface Viewing the IP Configuration Window IP Configuration Window-Detailed Description POS Interface ConfigurationViewing the POS Interface Configuration Window Generic Parameters Tab POS Interface Configuration Window-POS Config Tab Configuring a POS Interface BER TCA POS Interface Configuration Window-Detailed Description APS Interface Configuration APS Configuration Window-APS Tab Viewing the APS Configuration Window Removing a Working Interface Adding a Working InterfaceAdding a Protected Interface Removing a Protected Interface APS Configuration Window-Detailed Description APS TabAPS Interface Viewing the SRP Interface Configuration Attributes SRP Interface Configuration SRP Interface Configuration Window-Detailed Description Configuring a SRP Interface Viewing the SRP Interface Side Configuration Attributes SRP Interface Side Configuration 10 SRP Side Configuration window-Alarms tab Configuring a SRP Side SRP Interface Side Configuration Window-Detailed Description Alarms Tab OL-4455-01 Interface Type Interface Status Launching the Interface Status Windows Viewing the Generic Interface Status Window Generic Interface Status Interface Details Generic Interface Status Window-Detailed DescriptionLast Change Details Transmission Details Viewing the ATM Interface Status Window ATM Interface Status ATM Transmit Status ATM Interface Status Window-Detailed Description Physical Layer Status ATM Receive StatusATM Port Status Action Viewing the ATM Interface Faults Window ATM Interface Faults Fault Tab ATM Interface Faults Window-Detailed DescriptionDS3/E3 Interface Status Viewing the DS3/E3 Interface Status Window Status Tab DS3/E3 Interface Status Window-Detailed Description Far End DS3/E3 Status DS3/E3 Status Viewing the Sonet Interface Status Window Sonet Interface Status Sonet Interface Status-Section Tab Choose the Line tab, if required see Figure Choose the Path tab, if required see Figure Medium Sonet Status Window-Detailed DescriptionSection Line SRP Interface Status Viewing the SRP Interface Status AttributesVirtual Tributary Interface Tab SRP Interface Status Window-Detailed DescriptionSide a Frame Side B Frame Viewing the IPS Status Attributes SRP Side IPS Status IPS Status Window-Detailed Description SRP Topology MapViewing the SRP Topology Map IPS Status Topology Map SRP Topology Map-Detailed Description OL-4455-01 10-1 Interface Performance 10-2 Launching the Interface Performance Windows Generic Interface Performance Viewing the Generic Interface Performance Window10-3 Interface Performance Window-Performance 2 Tab 10-4 10-5 Starting Performance Logging for a Selected Interface Start Performance Logging Confirmation Window 10-6 10-7 Stopping Performance Logging for a Selected Interface Performance 1 Tab Generic Interface Performance Window-Detailed DescriptionGeneral Information Packets/Octets Statistics Performance 2 Tab Error StatisticsPerformance Logging 10-9 Viewing the Sonet Interface Performance Window Sonet Interface PerformancePerformance 3 Tab Packets/Octets Statistics High Capacity Sonet Interface Performance-Section Tab 10-11 Sonet Interface Performance-Line Tab 10-12 10 Sonet Interface Performance-Path Tab 10-13 Section Tab Sonet Performance Window-Detailed DescriptionLine Tab Line Viewing the DS3/E3 Interface Performance Window DS3/E3 Interface PerformancePath Tab Virtual Tributary Tab 11 DS3/E3 Interface Performance Window-DS3 Performance Tab 10-16 DS3/E3 Interface Performance Window-Detailed Description DS3 Performance Tab10-17 E3 Performance Tab Ethernet Interface Performance Viewing the Ethernet Interface Performance Window10-19 General Statistics Ethernet Interface Performance Window-Detailed DescriptionCollision Statistics 10-20 SRP Performance Viewing the SRP Performance Window10-21 15 SRP Performance window-Outer Ring tab 10-22 16 SRP Performance Window-Inner Ring Tab 10-23 10-24 SRP Performance Window-Detailed Description Utilization Counters for last x secondsData Traffic 10-25 10-26 Outer Ring Tab 10-27 Inner Ring Tab Side Tab SRP Side PerformanceSide a Data Traffic Bytes Side B Data Traffic Bytes 10-29 Viewing the SRP Side Performance Window 19 SRP Side Performance window-Host tab 10-30 Ring Tab SRP Side Performance Window-Detailed DescriptionPackets Packets Out Host Tab Octets Out10-32 Ring Errors TabHost 10-33 10-34 11-1 Launching the Layer 3 QoS Windows Layer 3 QoS Menu Options to Launch11-2 Committed Access Rate CAR Access ListsWeighted Random Early Detection Wred CAR and Wred Overview Mdrr Overview Towards the Fabric ToFabMdrr in Cisco 12000/10720 Router Manager 11-4 Implications of Engine Type CAR and Wred in Cisco 12000/10720 Router Manager11-5 Workflow for CAR CAR Policy ConfigurationPer Interface Rate Control Pirc Support 11-6 Limited Support for Engine Creating a CAR Policy11-7 11-8 Applying an Access List to a CAR Policy CAR Policy Configuration Tab CAR Policy Configuration Window-Detailed DescriptionAccess List Choice CAR Parameters Creating Access Lists Access List ConfigurationExceed Action 11-10 11-11 Access List Configuration-General Tab 11-12 Access List Configuration Window-Detailed Description IP Standard Tab IP Standard11-13 IP Precedence Tab IP Precedence11-14 11-15 MAC IP Extended IP Extended TabValid Protocol Names 11-16 Source and Destination Dynamic ListPort 11-17 CAR Policy Apply Applying a CAR Policy to an Interface11-18 Removing a CAR Policy from an Interface Editing or Deleting a CAR Policy11-19 CAR Policy Apply Window-Detailed Description CAR Policy Apply Tab11-20 Viewing the CAR Policy Status Window CAR Policy StatusApply Status 11-21 Workflow for WRED/DRR Engine Type Support for Wred11-22 CoS Queue Group Configuration Creating a CoS Queue Group Under Wred11-23 Editing an Existing CoS Queue Group Deleting an Existing CoS Queue Group11-24 CoS Queue Group Configuration Window-Detailed Description CoS Queue Group Tab11-25 11-26 Wred Parameters DRR Mapping DRR TabDRR Queue 11-27 Wred Tx Configuration Applying a CoS Queue Group to an Interface11-28 11-29 13 Wred Tx Configuration Window Removing a CoS Queue Group from an Interface Changing the Association of a CoS Queue Group11-30 Tx Config Tab Wred Tx Configuration Window-Detailed DescriptionAvailable COS Queue Group Associated COS Queue Group Info Wred ToFab Configuration Creating a ToFab Policy11-32 11-33 Editing an Existing ToFab policy 11-34 Deleting an Existing ToFab policy ToFab Policy Configuration tab Wred ToFab Policy Configuration Window-Detailed DescriptionSlot Table Parameters Slot-CosQ Groups Wred Rx Configuration Associating a ToFab Policy to a Line card11-36 Disassociating a ToFab Policy from a Line card Changing the Association of a ToFab Policy11-37 Rx Configuration Tab Wred Rx Configuration Window-Detailed DescriptionAssociated slot-Table Info Apply Status 12-1 Managing ATM Connections PVC Connections Terminating PVC Connections12-2 12-3 SVC Connections Launching the ATM Connections Windows ATM Connection Synchronization12-4 Policy Name Value DeviceisMaster default policyVCL in Cisco EMF VCL State VCL on Device Behavior 12-5 Normal Policy CEMFisMasterAfterFirstSync12-6 Creating ATM Connections Uploading Existing ATM Connections and QoS Profiles12-7 Without configuring the Management Password Information Configuring the Management Password InformationNaming Convention for the Uploaded Connection Objects 12-8 12-9 Viewing the ATM Connection Upload Window 12-10 Uploading Existing ATM Connections and ATM QoS Profiles Connection Upload Tab ATM Connection Upload Window-Detailed DescriptionUpload 12-11 Managing ATM QoS Profiles Creating ATM QoS Profiles12-12 12-13 ATM QoS Profiles Configuration Window-Profile Tab 12-14 Editing an ATM QoS Profile 12-15 Deleting an ATM QoS Profile 10 Deployment Wizard-Summary Window 12-16 Profile Tab ATM QoS Profiles Configuration Window-Detailed DescriptionRxTx Parameters Tab Category Deploying a PVC Object Deploying ATM Connection ObjectsObject Type to be 12 Deployment Wizard-Templates 12-19 14 Deployment Wizard-Object Parameters 12-20 15 Object Selector Window 12-21 12-22 Deploying an SVC Object 18 Deployment Wizard-Object Parameters 12-23 19 Deployment Wizard-Object Parameters 12-24 20 Deployment Wizard-Views 12-25 21 Deployment Wizard-Object Selector 12-26 22 Deployment Wizard-Object Parameters 12-27 12-28 Applying an ATM QoS Profile to an ATM Connection 24 ATM QoS Profiles Management-Profile Tab 12-29 ATM PVC Configuration Viewing the ATM VCL Configuration Window12-30 12-31 Connecting or Disconnecting a PVC Decommissioning or Re-Commissioning a PVC ATM OAM Ping12-32 12-33 27 ATM VCL Configuration-OAM Ping tab Traffic Information ATM VCL Configuration Window-Detailed DescriptionEncapsulation Parameters 12-34 VCL Config Layer 3 Configuration TabOAM Information Interface Subscriber OAM Ping TabOAM Parameters OAM Ping Parameters SVC Configuration Viewing the SVC Configuration Window12-37 SVC Configuration Window-Detailed Description Connecting or Disconnecting an SVCConfiguration Decommissioning or Recommissioning an SVC SVC Parameters VC Parameters12-39 12-40 PVC Status PVC Status ATM VCL Status Window-Detailed DescriptionSoft PVC Details 12-41 OAM tab CharacteristicsOAM Details Auto Detect Statistics 13-1 Launching the Vlan Windows 13-2 Vlan Synchronization Vlan Synchronize Window 13-3 Deploying Vlan objects Deploying a Domain13-4 Deploying a Vlan object 13-5 Deployment Wizard-Object Parameters Window 13-6 13-7 10 Deployment Wizard-Templates Window 13-8 11 Deployment Wizard-Object Parameters Window 13-9 13-10 14 Deployment Wizard-Views 13-11 13-12 16 Deployment Wizard-Views 13-13 Vlan Configuration Viewing the Vlan Configuration Window13-14 13-15 Commissioning a Vlan 13-16 Decommissioning a Vlan 13-17 Start Performance Logging 13-18 Stop Performance Logging Vlan Performance Vlan Configuration Window-Detailed DescriptionStatus 13-19 13-20 Viewing the Vlan Performance Window Reparenting VLANs and Vlan Sub-Interfaces Vlan Performance Window-Detailed Description13-21 13-22 Deleting Vlan Objects 26 Deployment Wizard-Summary 13-23 13-24 14-1 Launching the Routing Windows 14-2 BGP Management BGP Configuration Viewing the BGP Details Tab on the BGP Configuration Window14-3 BGP Details Tab-Detailed Description BGP General14-4 Enabling BGP on a Chassis BGP Information14-5 14-6 Enable BGP Window-Detailed Description 14-7 Modifying BGP on a Chassis BGP Modify Window-Detailed Description Disabling BGP on a Chassis14-8 14-9 Viewing the Network Tab on the BGP Configuration Window Network Tab-Detailed Description BGP Network Information14-10 BGP Network Configuration BGP Network Configuration Window-Detailed Description14-11 14-12 Viewing the Neighbor Tab on the BGP Configuration Window Neighbor Tab-Detailed Description BGP Neighbor ConfigurationBGP Neighbor Information 14-13 14-14 BGP Neighbor Configuration Window-Detailed Description 14-15 BGP Configuration Window-Redistribution Tab Redistribution Tab-Detailed Description BGP Redistribute ConfigurationBGP Redistribution Information 14-16 14-17 BGP Redistribute Configuration-Detailed Description BGP Status Viewing the BGP Status Window14-18 12 BGP Status-Network Tab 14-19 13 BGP Status-Neighbor Tab 14-20 BGP-Details BGP Status Window-Detailed DescriptionBGP General BGP Information Neighbor NetworkBGP Network Information BGP Neighbor Information Redistribution BGP Address-Family SynchronizationBGP Redistribution Information 14-23 15 BGP Address-Family Synchronization Window 14-24 16 Action Report 14-25 BGP Address-Family Synchronization-Detailed Description BGP Address Family ConfigurationSynchronization Tab 14-26 14-27 18 BGP Address-Family Configuration Window AF-General Tab-Detailed Description Configuring Address FamilyBGP Address Family Information 14-28 Configure Address Family-Detailed Description Add Address Family14-29 14-30 Modifying BGP Address Family 14-31 Modify Address Family Parameters 14-32 21 BGP Address-Family Configuration Window-AF-Network Tab AF-Network Tab-Detailed Description BGP Address Family-Network ConfigurationNetwork Information 14-33 14-34 Add/Remove Network 14-35 23 BGP Address-Family Configuration Window-AF-Neighbor Tab AF-Neighbor Tab-Detailed Description BGP Address Family-Neighbor ConfigurationNeighbor Information 14-36 14-37 Add/Remove Neighbor 14-38 AF-Redistribute Tab-Detailed Description Redistribute Information14-39 14-40 BGP Address Family-Redistribute Configuration Viewing the BGP Address-Family Status window BGP Address-Family StatusAdd/Remove Redistribution Information 14-41 27 BGP Address-Family Status Window 14-42 28 BGP Status-AF-Network Tab 14-43 29 BGP Status-AF-Neighbor Tab 14-44 AF-General BGP Address-Family Status Window-Detailed DescriptionBGP Address Family Information 14-45 AF-Network AF-NeighborAF-Redistribute Viewing the Ospf Configuration Window Ospf ConfigurationOspf Management 14-47 Config Tab-Detailed Description Config14-48 14-49 Adding an Ospf Process 14-50 Removing an Ospf Process Viewing the Network Tab on the Ospf Configuration Window Ospf Network14-51 14-52 Configuring a Network 37 Action Report 14-53 Configure Network Configure Network-Detailed DescriptionOspf Status Viewing the Ospf Status Window 39 Ospf Status Window 14-55 40 Ospf Status-Process Information Tab 14-56 41 Ospf Status-Area Tab 14-57 42 Ospf Status-Interface Tab 14-58 43 Ospf Status-Neighbor Tab 14-59 44 Ospf Status-Link State Tab 14-60 Ospf Status-Detailed Description General Group14-61 Area Process InformationProcess Summary Network Details Stub Area InterfaceArea Range 14-63 Interface Metric Virtual Interface14-64 Neighbor Virtual Neighbor14-65 Host Link StateLsdb Hosts 15-1 Introduction 15-2 Mpls Management Workflow Launching the Mpls Management Windows Window/Task Menu Options to Select to Open Window15-3 Mpls Forwarding Information Viewing the Mpls Forwarding Information Window15-4 Mpls Forwarding Information Window-Detailed Description Mpls Forwarding Information Tab15-5 Mpls Interface Status Fault Management for Mpls LSR InterfacesViewing the Mpls Interface Status Window 15-6 Mpls Interface Status Window-Detailed Description Interface Configuration TabGeneral 15-7 Mpls Interface Information Viewing the Mpls Interface Information Window15-8 Mpls Interface Information Window-Detailed Description Interface Setup TabSelect Interface 15-9 15-10 Mpls Setup Tab 15-11 Interface Performance Tab 15-12 Mpls Performance Tab Mpls Interface Information Window-MPLS Performance Tab 15-13 Mpls Interface Performance Performance Management for Mpls LSR InterfacesViewing the Mpls Interface Performance Window 15-14 General Performance Statistics Tab Mpls Interface Performance Window-Detailed DescriptionCounters 15-15 Mpls Performance Statistics Tab High Speed Counters15-16 Incoming Direction Outgoing Direction15-17 Mpls LDP Entity Status Window Fault Management for Mpls LDPViewing the Mpls LDP Entity Status Window 15-18 Mpls LDP Entity Status Window-Detailed Description Entity Tab15-19 15-20 General LDP Status Entity Statistics Tab Entity Statistics15-21 15-22 General Label Range Tab 15-23 General Label Range ATM Parameters Tab ATM Parameters15-24 ATM Label Range Tab ATM Label Range15-25 Mpls LDP Hello Adjacencies Viewing the Mpls LDP Hello Adjacencies Window15-26 Hello Adjacencies Tab Mpls LDP Hello Adjacencies Window-Detailed DescriptionHello Adjacencies 15-27 Mpls LDP Peer Status Viewing the Mpls LDP Peer Status Window15-28 Peers Tab Mpls LDP Peer Status Window-Detailed DescriptionSessions Tab LDP Peers 15-30 LDP Sessions Session Statistics Tab LDP Session Statistics15-31 ATM Sessions Tab LDP ATM Session15-32 Mpls Tunnel Information Fault Management for Mpls Traffic EngineeringViewing the Mpls Tunnel Information Window 15-33 Mpls Tunnel Information Window-Detailed Description Select Tunnel Tab15-34 Head Tunnel Setup Tab Select Tunnel15-35 15-36 Tunnel Info Tunnel Status Advanced15-37 15-38 Head Tunnel Hops Tab LSP Setup Tab Hop Table15-39 15-40 22 Mpls Tunnel Information Window-LSP Setup Tab 15-41 15-42 LSP Hops Tab Actual Route HOP Table Computed HOP Table15-43 15-44 LSP Resource Tab Resource Table Performance TabTunnel Performance 15-45 15-46 16-1 Introduction to VRF Management Launching the Mpls VRF Management Windows VRF Management WorkflowsRouter Manager Window 16-2 Creating VRF Objects in the EM Deploying VRF Objects16-3 Deploying a VRF Object 16-4 Deployment Wizard Views 16-5 Object Selector Window 16-6 Deployment Wizard-Views 16-7 Creating and Configuring the VRF Policy on a Device Configuring and Creating a VRF Policy on a Selected Chassis16-8 16-9 VRF Configuration Window Adding a Routing Target to a Selected Chassis Removing a VRF Policy from a Selected ChassisDeleting a Routing Target from a Selected Chassis 16-10 VRF Configuration Tab VRF Configuration Window-Detailed Description Device Action Associating a VRF Policy with an InterfaceExport Import 16-13 Associating VRF Policies VRF Association Window-Detailed Description Removing a VRF Policy from a Selected InterfaceVRF Tab Available VRF Policies VRF Status VRF Fault ManagementViewing the VRF Status Window 16-15 VRF Status Window-Detailed Description VRF Details16-16 16-17 Performance and Security Tab Performance Security16-18 Interface VRF Status Viewing the Interface VRF Status Window16-19 VPN Status Interface VRF Status Window-Detailed DescriptionInterface VRF Association Tab Viewing the VPN Status Window 16-21 VPN Status Window-Detailed Description Routes Tab VRF Routes16-22 16-23 Route Targets Tab 16-24 VRF Route Targets BGP Neighbor Tab Interface MPLS/EBGP Neighbor16-25 VRF Object Status Viewing the VRF Object Status Window16-26 16-27 VRF Object Status Window-Detailed Description 16-28 Routes 16-29 16-30 Route Targets Interface Association Tab Interface Association16-31 16-32 Performance Tab 17-1 Trap Alarm Description Severity Clears 17-2 17-3 Enabling/Disabling Traps on the Device Mpls Trap Configuration Window-Detailed Description Traps Tab17-4 Mpls CLI Troubleshooting Services Launching the Mpls CLI Troubleshooting Services Windows17-5 17-6 Verify Routing Protocols 17-7 Verify Routing Tables 17-8 Verify CEF Switching 17-9 Verify CEF Switching Summary 17-10 Verify Mpls Interfaces 17-11 Verify Label Distribution 17-12 Verify Label Bindings 17-13 Verify Interface CEF Switching 17-14 Cisco 12000/10720 Router Manager Alarms Color Severity of Alarms18-1 Viewing Alarms Cisco 12000/10720 Router Trap Support18-2 18-3 Chassis Alarms 18-4 Interface Alarms Syslog Traps18-5 Configuration Management Traps Trap Alarm Description18-6 Connectivity Management Heartbeat PollingOperational Status Polling Disabling Heartbeat Polling 18-8 Performance Logging 19-1 Change Management Inserting a Line Card Mismatched State19-2 Line Card in Mismatched State 19-3 19-4 Removing a Line Card 19-5 19-6 20-1 Performance Management and Historical Data Viewing the Performance Manager Window Monitored Attribute Description20-2 20-3 Performance Manager window appears see Figure 20-4 Viewing Performance Statistics Viewing a Chart Press Action20-5 Saving Performance Data to a File Printing a Performance FileArchiving 20-6 Performance Manager Window-Detailed Description Exporting a Performance FileMonitored Attributes 20-7 Summary Time PeriodStart End Refresh Line Chart TabTable Display Tab 20-9 20-10 Administration AdministrationConfiguration What Version is the Software? 21-2 What Dialogs Use the IOS CLI Instead of SNMP? Configuration Verifying SNMP, Log, and Trap Settings21-3 21-4 Show running-config begin snmp ATM Sub-Interface Configuration BGP ConfigurationATM IP Configuration GUI Display Error Settings 21-5 21-6 Viewing ATM Physical Port Configurations? SONET/SDH Conversion Chart OL-4455-01 GUI Synchronization Details GUIs that Synchronize with the Device when Launched GUIs that do not Synchronize with the Device when Launched Setup Network Diagram Analysis of Problem Problem Local Outgoing Prefix Bytes Tag Next Hop Solution Tag Tag or VC Or Tunnel Id Switched Interface Running Configs PE1 No ip mroute-cache Interface POS4/0/0 Bandwidth Network 0.0.0.0 255.255.255.255 area Router bgp Interface GigabitEthernet1/0 Pvc test5 254/5 Pvc test6 254/6 Pvc test4 254/10 PE2 CE2 Redundancy No keepalive-enable Enable password atlantech OL-4455-01 IN-1 APS IN-2 Clli IN-3 IN-4 IN-5 IN-6