Configuring Address Family | Cisco Systems 12000/10700 V3.1.1

Chapter 14

Routing

BGP Address Family Configuration

AF-General Tab—Detailed Description

The AF-General tab displays two areas: BGP General and BGP Address Family Information.

BGP General

Local Autonomous System—The id of the BGP process running in the device. If the value is 0 it means no BGP process is running on the device.

BGP Address Family Information

Address Family—Unique identifier of the address family type.

VRF Name—Identifier of the VRF Name if the address family type is ipv4 vrf.

Auto Summary—Displays whether the automatic network number summarization is enabled/disabled for the address family.

Synchronization—Displays whether the BGP synchronization with IGP is enabled/disabled for the address family.

Note This field is applicable only for the ipv4 unicast and ipv4 vrf address families.

Default Metric—Displays the default metric value set for redistributed routes of the address family.

Action

Modify Address Family—Clicking on the “Modify Address Family” button, opens the BGP Address Family - Modify Address Family Parameters window.

Add/Remove Address Family—Clicking on the “Add/Remove Address Family” button, opens the Configure Address Family window.

Configuring Address Family

The Configure Address Family window allows the user to create or remove BGP address families. To add or remove a BGP address family, proceed as follows:

Step 1 Open the BGP Address-Family Configuration window. See “Viewing the AF-General Tab on the BGP Address-Family Configuration Window” section on page 14-27for further details. Click on the AF-General Tab.

Step 2 Choose the chassis from the left side of the window.

Note You can choose multiple chassis (from the chassis list) which allows you to launch the Configure Address Family window for the selected chassis.

Step 3 Click on the Add/Remove Address Family button to open the Configure Address Family window.

	Cisco 12000/10700 v3.1.1 Router Manager User Guide
14-28	OL-4455-01

Image 418

Cisco Systems 12000/10700 V3.1.1 manual AF-General Tab-Detailed Description, Configuring Address Family, 14-28

Contents

Cisco 12000/10700 v3.1.1 Router Manager User Guide Corporate Headquarters Cisco 12000/10700 v3.1.1 Router Manager User Guide N T E N T S Iii Views Object States Chassis Fault Management Window-Detailed Description RPR Status Viewing the RPR Status Window Vii Module Performance Window-Detailed Description Viii Interface Configuration SRP Interface Side Configuration Sonet Interface Status Virtual Tributary Tab Xii CAR Policy Configuration Xiii Xiv Deleting an Existing ToFab policy OAM tab Configuration Tab Xvi BGP-Details14-21 Xvii Redistribute Information Xviii Mpls Interface Status Xix Interface VRF Status Mpls Trap Management Xxi Archiving Xxii Running Configs C-4 CE1 C-4 PE1 C-5 PE2 C-11 CE2 C-12 Xxiii Xxiv Document Audience Xxv Document Organization Chapter Number Chapter Title ContentXxvi Managing VLANs Xxvii Example Conventions Command ConventionsConventions Format Description Example Cisco.com Obtaining DocumentationDocument Conventions Xxix Documentation Feedback Documentation CD-ROMOrdering Documentation Xxx Technical Assistance Center Obtaining Technical AssistanceXxxi Cisco TAC Escalation Center Obtaining Additional Publications and InformationCisco TAC Website Xxxii Xxxiii Xxxiv Overview A P T E R Cisco 12000/10720 Router Manager Software Cisco Element Manager Framework Cisco EMF Software Overview Accessing Online Help Concepts Physical Objects See Physical Interfaces and Technologies section on Cisco 12000/10720 Router Chassis Cisco 12016 Chassis Linecards Supporting ModulesPhysical Interfaces and Technologies Logical Objects POS Logical Object Management Functions Use of Telecom Graphics ObjectsLogical Object Management Functions You Can Perform Sample Telecom Graphical Object Sample Cisco 12000 Chassis Showing Telecom Graphical Objects OSI Mappings Views Component Managed View Physical View Layer 3 QoS ViewNetwork View Vlan View Cisco 12000/10720 Router Manager Object States Cisco 12000/10720 Router Manager Object States Normal State ErroredDecommissioned State Performance Logging On Mismatched Lost CommsDiscovery Lost Comms Transient Object States OL-4455-01 Getting Started Cisco 12000/10720 Router Manager Workflow ATM Starting Cisco EMF and Cisco 12000/10720 Router Manager Starting a Cisco EMF User Session Login window see -2 appears Launchpad Launching an Application Groups AccessMap Viewer Viewer Event Browser Events Thresholding Regimes Notification ProfilesEvent Groups Quitting a Cisco EMF User Session DeploymentPreFilter Deployment Process Outline Manually Deploying a Generic Site Object Deployment Process Workflow Choose DeploymentDeploy Generic Objects Deployment Wizard Templates Window Deployment Wizard Object Parameters Window 1 Deployment Wizard Object Parameters Window 2 Deployment Wizard Views window appears Object Selector Window appears 11 Deployment Wizard-Views Window 12 Deployment Wizard-Summary Window IP Auto Discovery of the Cisco Chassis Manually Deploying a Cisco 12000/10720 Chassis 14 Example of Auto Discovery 15 Deployment Wizard-Object Parameters 1 16 Deployment Wizard-Object Parameters Window 3 Click on Select. The Object Selector window appears 18 Object Selector Window 20 Deployment Wizard Summary Commissioning and Subchassis Discovery 21 Before Subchassis Discovery Commissioning a Chassis 22 Chassis Configuration Window 23 After Subchassis Discovery Decommissioning a Chassis Manually Deploying ModulesObject States User Named vs. Auto Named Module Deployment Manually Deploying a GRP Card 24 Deployment Wizard-Templates 25 Deployment Wizard-Object Parameters Click Select. The Object Selector window appears 27 Object Selector Window 28 Deployment Wizard-Views 29 Deployment Wizard-Summary Line Cards Supported by Cisco 12000 Series Routers Manually Deploying Line CardsCard Type Menu Option Card Description SR-SC LR-SC Ethernet Line Cards Supported by Cisco 12000 Series Routers Cisco 12000/10720 Router Manager Menu Option Card Description Line Cards Supported by Cisco 10720 Routers POS LR2 30 Deployment Wizard-Templates 31 Deployment Wizard-Object Parameters 32 Deployment Wizard-Views 33 Object Selector Window 34 Deployment Wizard-Views Deployment Wizard-Summary window appears Deploying a Clock Scheduler Card Manually Deploying Supporting ModulesCard Card Type Card Description 36 Deployment Wizard-Views 37 Object Selector Window 38 Deployment Wizard-Views 39 Deployment Wizard-Summary Deploying a Switch Fabric Card 40 Deployment Wizard-Views 41 Object Selector Window 42 Deployment Wizard-Views Pre-deployment 43 Deployment Wizard-Summary Performing Pre-deployment OL-4455-01 Managing Chassis Menu Options to Select to Open Window Launching the Chassis Management WindowsManager Window/Task Management Information Viewing the Management Information Window System Configuration Management Information Window-Configuration Tab Entering or Changing IOS CLI Username and Passwords Choose the IOS/Command Line Security tab System Configuration Configuration TabIOS/Command Line Security Tab IOS Username and Passwords Chassis Configuration Viewing the Chassis Configuration Window Commissioning a Chassis Decommissioning a Chassis Starting Global Performance Logging Action Report Window Stopping Global Performance Logging Entering Additional Descriptions for a Selected Chassis Choose the Additional Descriptions tab Device Management Tab in Configuration Window Choose the Device Management tab Chassis Configuration Window-Detailed Description Device Management Tab Snmp ManagementAdditional Descriptions Tab Commission Status Viewing the Snmp Management Window Modifying Snmp Community Names or Version Snmp Management Window-Detailed Description Enabling or Disabling Trap GenerationCommunity Names Version Chassis InventoryViewing the Chassis Inventory Window Trap Generation Chassis Inventory Window-Detailed Description General Tab Asset Tracking Tab Chassis Fault Management Viewing the Chassis Fault Management Window 10 Chassis Fault Management Window-General Tab 11 Chassis Fault Management Window-Power Supply Tab 12 Chassis Fault Management Window-Temperature Tab 13 Chassis Fault Management Window-Fan Tab Changing Column Width Chassis Availability Chassis Fault Management Window-Detailed DescriptionPower Supply Tab LED Status Fan Tab Temperature TabTemperature Voltage Command Log Viewing the Command Log Window Command Log Details Tab Command Log Window-Detailed DescriptionCommand Log Details Table Viewing the SysLog Messages Window System LogEvent History Details System Log Window-Detailed Description SysLog Message Tab SysLog Messages Area Using RME for Chassis Management TasksSys Log Message Details APS Status Configuration Backup/Restore Using RMEIOS Image Download Using RME Viewing the APS Status Window 16 APS Status Window APS Status Window-Detailed Description Initiating a Telnet ServiceAPS Circuits Area Viewing the Configuration Editor Window Configuration EditorLaunching the Web Console 18 Configuration Editor Window Configuration Editor Tab Configuration Editor Window-Detailed DescriptionSearching in the Configuration Editor Selection Operations on Device RPR ConfigurationViewing the RPR Configuration Window Operations Done Locally RPR Configuration Window-Detailed Description 19 RPR Configuration Window RPR Status Switch Over TabViewing the RPR Status Window RPR Status Window-Detailed Description RP Status Viewing the IP Routing Status window IP Routing StatusLC Status Classless Inter-Domain Routing Tab IP Routing Status Window-Detailed DescriptionCidr Info TCP Status Viewing the TCP Status Window 22 TCP Status Window TCP Status Tab TCP Status Window-Detailed DescriptionTCP Status TCP Connections Tab Connections Table UDP Status Viewing the UDP Status Window UDP Status Window-Detailed Description Status UDP Port Information Cisco 12000/10720 Router Manager Module Names Module Abbreviation Launching the Module Management Windows Cisco 12000/10720 Router Module Configuration Viewing the Configuration Window Configuration Window Commissioning a Selected Module Decommissioning a Selected Module To decommission a module, proceed as follows Module Configuration Window-Detailed Description Module Fault ManagementViewing the Module Fault Management Window Module Fault Management Window-Detailed Description Module Availability Module Performance Cisco Contact Details Viewing the Module Performance Window Starting or Stopping Performance Logging CPU Usage Module Performance Window-Detailed DescriptionPerformance Logging Module Inventory Viewing the Module Inventory Window General Module Inventory Window-Detailed DescriptionModule Details Asset Tracking Slot & Ports Managing Interfaces Interface Interface Profiles Interface Profile Types Launching the Interface Profile Windows Creating an ATM Interface Profile Not applicable for Cisco 12000/10720 Router Manager Prompt Window Editing an Existing ATM Interface Profile Deleting an Existing ATM Interface Profile Configuration 1 Tab ATM Configuration Information Element Layer Configuration 2 TabIlmi Configuration Physical Layer Creating an Hsrp Profile Hsrp Profile Window Editing an Existing Hsrp Interface Profile Hsrp Profile Window-Detailed Description Deleting an Existing Hsrp Interface ProfileHsrp Profile Parameters Area Creating a POS Interface Profile Actions POS Profile Dialog -POS Config Tab Editing an Existing POS Interface Profile POS Profile Window-Detailed Description POS Config TabDeleting an Existing POS Interface Profile General Alarm Reporting Alarm Reporting & ThresholdSonet Overhead Creating a SRP Side Profile 11 SRP Side Profile Window 12 SRP Side Profile Window-Alarms tab Editing an Existing SRP Side Profile Deleting an Existing SRP Side Profile SRP Side Profile Window-Detailed Description 14 Deletion Prompt Window Create Profile Alarms TabReporting and Threshold Reporting Interface Configuration Interfaces and Related Technology-Specific Windows Launching the Interface Configuration Windows Interfaces Generic Interface Configuration Viewing the Generic Interface Configuration Window Configuring and Commissioning a Generic Interface Configurable Parameters Generic Interface Configuration Window-Detailed DescriptionDecommissioning an Interface ATM Interface Configuration Viewing the ATM Interface Configuration Window Configuring an ATM Interface ATM Interface Configuration Window-Configuration 1 Tab ATM Interface Configuration Window-Detailed Description Ethernet Interface Configuration Viewing the Ethernet Interface Configuration Window Ethernet Interface Configuration Window-Configuration Tab Configuring an Ethernet Interface Ethernet Interface Configuration Window-HSRP Parameters Tab Ethernet Interface Configuration Window-Detailed Description Hsrp Parameters Tab IP Configuration Hsrp Parameters Viewing the IP Configuration Window Configuring an IP Interface Viewing the POS Interface Configuration Window POS Interface ConfigurationIP Configuration Window-Detailed Description Generic Parameters Tab Configuring a POS Interface POS Interface Configuration Window-POS Config Tab POS Interface Configuration Window-Detailed Description BER TCA APS Interface Configuration Viewing the APS Configuration Window APS Configuration Window-APS Tab Adding a Protected Interface Adding a Working InterfaceRemoving a Working Interface Removing a Protected Interface APS Tab APS Configuration Window-Detailed DescriptionAPS Interface SRP Interface Configuration Viewing the SRP Interface Configuration Attributes Configuring a SRP Interface SRP Interface Configuration Window-Detailed Description SRP Interface Side Configuration Viewing the SRP Interface Side Configuration Attributes Configuring a SRP Side 10 SRP Side Configuration window-Alarms tab SRP Interface Side Configuration Window-Detailed Description Alarms Tab OL-4455-01 Interface Status Interface Type Launching the Interface Status Windows Generic Interface Status Viewing the Generic Interface Status Window Last Change Details Generic Interface Status Window-Detailed DescriptionInterface Details Transmission Details ATM Interface Status Viewing the ATM Interface Status Window ATM Interface Status Window-Detailed Description ATM Transmit Status ATM Port Status ATM Receive StatusPhysical Layer Status Action ATM Interface Faults Viewing the ATM Interface Faults Window DS3/E3 Interface Status ATM Interface Faults Window-Detailed DescriptionFault Tab Viewing the DS3/E3 Interface Status Window DS3/E3 Interface Status Window-Detailed Description Status Tab DS3/E3 Status Far End DS3/E3 Status Sonet Interface Status Viewing the Sonet Interface Status Window Sonet Interface Status-Section Tab Choose the Line tab, if required see Figure Choose the Path tab, if required see Figure Section Sonet Status Window-Detailed DescriptionMedium Line Viewing the SRP Interface Status Attributes SRP Interface StatusVirtual Tributary Side a Frame SRP Interface Status Window-Detailed DescriptionInterface Tab Side B Frame SRP Side IPS Status Viewing the IPS Status Attributes Viewing the SRP Topology Map SRP Topology MapIPS Status Window-Detailed Description IPS Status SRP Topology Map-Detailed Description Topology Map OL-4455-01 Interface Performance 10-1 Launching the Interface Performance Windows 10-2 Viewing the Generic Interface Performance Window Generic Interface Performance10-3 10-4 Interface Performance Window-Performance 2 Tab Starting Performance Logging for a Selected Interface 10-5 10-6 Start Performance Logging Confirmation Window Stopping Performance Logging for a Selected Interface 10-7 General Information Generic Interface Performance Window-Detailed DescriptionPerformance 1 Tab Packets/Octets Statistics Performance Logging Error StatisticsPerformance 2 Tab 10-9 Performance 3 Tab Sonet Interface PerformanceViewing the Sonet Interface Performance Window Packets/Octets Statistics High Capacity 10-11 Sonet Interface Performance-Section Tab 10-12 Sonet Interface Performance-Line Tab 10-13 10 Sonet Interface Performance-Path Tab Line Tab Sonet Performance Window-Detailed DescriptionSection Tab Line Path Tab DS3/E3 Interface PerformanceViewing the DS3/E3 Interface Performance Window Virtual Tributary Tab 10-16 11 DS3/E3 Interface Performance Window-DS3 Performance Tab DS3 Performance Tab DS3/E3 Interface Performance Window-Detailed Description10-17 E3 Performance Tab Viewing the Ethernet Interface Performance Window Ethernet Interface Performance10-19 Collision Statistics Ethernet Interface Performance Window-Detailed DescriptionGeneral Statistics 10-20 Viewing the SRP Performance Window SRP Performance10-21 10-22 15 SRP Performance window-Outer Ring tab 10-23 16 SRP Performance Window-Inner Ring Tab SRP Performance Window-Detailed Description 10-24 Data Traffic Counters for last x secondsUtilization 10-25 Outer Ring Tab 10-26 Inner Ring Tab 10-27 Side a Data Traffic Bytes SRP Side PerformanceSide Tab Side B Data Traffic Bytes Viewing the SRP Side Performance Window 10-29 10-30 19 SRP Side Performance window-Host tab Packets SRP Side Performance Window-Detailed DescriptionRing Tab Packets Out Octets Out Host Tab10-32 Host Errors TabRing 10-33 10-34 Launching the Layer 3 QoS Windows 11-1 Menu Options to Launch Layer 3 QoS11-2 Weighted Random Early Detection Wred Access ListsCommitted Access Rate CAR CAR and Wred Overview Mdrr in Cisco 12000/10720 Router Manager Towards the Fabric ToFabMdrr Overview 11-4 CAR and Wred in Cisco 12000/10720 Router Manager Implications of Engine Type11-5 Per Interface Rate Control Pirc Support CAR Policy ConfigurationWorkflow for CAR 11-6 Creating a CAR Policy Limited Support for Engine11-7 Applying an Access List to a CAR Policy 11-8 Access List Choice CAR Policy Configuration Window-Detailed DescriptionCAR Policy Configuration Tab CAR Parameters Exceed Action Access List ConfigurationCreating Access Lists 11-10 Access List Configuration-General Tab 11-11 Access List Configuration Window-Detailed Description 11-12 IP Standard IP Standard Tab11-13 IP Precedence IP Precedence Tab11-14 MAC 11-15 Valid Protocol Names IP Extended TabIP Extended 11-16 Port Dynamic ListSource and Destination 11-17 Applying a CAR Policy to an Interface CAR Policy Apply11-18 Editing or Deleting a CAR Policy Removing a CAR Policy from an Interface11-19 CAR Policy Apply Tab CAR Policy Apply Window-Detailed Description11-20 Apply Status CAR Policy StatusViewing the CAR Policy Status Window 11-21 Engine Type Support for Wred Workflow for WRED/DRR11-22 Creating a CoS Queue Group Under Wred CoS Queue Group Configuration11-23 Deleting an Existing CoS Queue Group Editing an Existing CoS Queue Group11-24 CoS Queue Group Tab CoS Queue Group Configuration Window-Detailed Description11-25 Wred Parameters 11-26 DRR Queue DRR TabDRR Mapping 11-27 Applying a CoS Queue Group to an Interface Wred Tx Configuration11-28 13 Wred Tx Configuration Window 11-29 Changing the Association of a CoS Queue Group Removing a CoS Queue Group from an Interface11-30 Available COS Queue Group Wred Tx Configuration Window-Detailed DescriptionTx Config Tab Associated COS Queue Group Info Creating a ToFab Policy Wred ToFab Configuration11-32 Editing an Existing ToFab policy 11-33 Deleting an Existing ToFab policy 11-34 Slot Table Parameters Wred ToFab Policy Configuration Window-Detailed DescriptionToFab Policy Configuration tab Slot-CosQ Groups Associating a ToFab Policy to a Line card Wred Rx Configuration11-36 Changing the Association of a ToFab Policy Disassociating a ToFab Policy from a Line card11-37 Associated slot-Table Info Wred Rx Configuration Window-Detailed DescriptionRx Configuration Tab Apply Status Managing ATM Connections 12-1 Terminating PVC Connections PVC Connections12-2 SVC Connections 12-3 ATM Connection Synchronization Launching the ATM Connections Windows12-4 VCL in Cisco EMF VCL State VCL on Device Behavior DeviceisMaster default policyPolicy Name Value 12-5 CEMFisMasterAfterFirstSync Normal Policy12-6 Uploading Existing ATM Connections and QoS Profiles Creating ATM Connections12-7 Naming Convention for the Uploaded Connection Objects Configuring the Management Password InformationWithout configuring the Management Password Information 12-8 Viewing the ATM Connection Upload Window 12-9 Uploading Existing ATM Connections and ATM QoS Profiles 12-10 Upload ATM Connection Upload Window-Detailed DescriptionConnection Upload Tab 12-11 Creating ATM QoS Profiles Managing ATM QoS Profiles12-12 ATM QoS Profiles Configuration Window-Profile Tab 12-13 Editing an ATM QoS Profile 12-14 Deleting an ATM QoS Profile 12-15 12-16 10 Deployment Wizard-Summary Window RxTx Parameters Tab ATM QoS Profiles Configuration Window-Detailed DescriptionProfile Tab Category Object Deploying ATM Connection ObjectsDeploying a PVC Object Type to be 12-19 12 Deployment Wizard-Templates 12-20 14 Deployment Wizard-Object Parameters 12-21 15 Object Selector Window Deploying an SVC Object 12-22 12-23 18 Deployment Wizard-Object Parameters 12-24 19 Deployment Wizard-Object Parameters 12-25 20 Deployment Wizard-Views 12-26 21 Deployment Wizard-Object Selector 12-27 22 Deployment Wizard-Object Parameters Applying an ATM QoS Profile to an ATM Connection 12-28 12-29 24 ATM QoS Profiles Management-Profile Tab Viewing the ATM VCL Configuration Window ATM PVC Configuration12-30 Connecting or Disconnecting a PVC 12-31 ATM OAM Ping Decommissioning or Re-Commissioning a PVC12-32 27 ATM VCL Configuration-OAM Ping tab 12-33 Encapsulation Parameters ATM VCL Configuration Window-Detailed DescriptionTraffic Information 12-34 OAM Information Layer 3 Configuration TabVCL Config Interface OAM Parameters OAM Ping TabSubscriber OAM Ping Parameters Viewing the SVC Configuration Window SVC Configuration12-37 Configuration Connecting or Disconnecting an SVCSVC Configuration Window-Detailed Description Decommissioning or Recommissioning an SVC VC Parameters SVC Parameters12-39 PVC Status 12-40 Soft PVC Details ATM VCL Status Window-Detailed DescriptionPVC Status 12-41 OAM Details CharacteristicsOAM tab Auto Detect Statistics Launching the Vlan Windows 13-1 Vlan Synchronization 13-2 13-3 Vlan Synchronize Window Deploying a Domain Deploying Vlan objects13-4 13-5 Deploying a Vlan object 13-6 Deployment Wizard-Object Parameters Window 13-7 13-8 10 Deployment Wizard-Templates Window 13-9 11 Deployment Wizard-Object Parameters Window 13-10 13-11 14 Deployment Wizard-Views 13-12 13-13 16 Deployment Wizard-Views Viewing the Vlan Configuration Window Vlan Configuration13-14 Commissioning a Vlan 13-15 Decommissioning a Vlan 13-16 Start Performance Logging 13-17 Stop Performance Logging 13-18 Status Vlan Configuration Window-Detailed DescriptionVlan Performance 13-19 Viewing the Vlan Performance Window 13-20 Vlan Performance Window-Detailed Description Reparenting VLANs and Vlan Sub-Interfaces13-21 Deleting Vlan Objects 13-22 13-23 26 Deployment Wizard-Summary 13-24 Launching the Routing Windows 14-1 BGP Management 14-2 Viewing the BGP Details Tab on the BGP Configuration Window BGP Configuration14-3 BGP General BGP Details Tab-Detailed Description14-4 BGP Information Enabling BGP on a Chassis14-5 Enable BGP Window-Detailed Description 14-6 Modifying BGP on a Chassis 14-7 Disabling BGP on a Chassis BGP Modify Window-Detailed Description14-8 Viewing the Network Tab on the BGP Configuration Window 14-9 BGP Network Information Network Tab-Detailed Description14-10 BGP Network Configuration Window-Detailed Description BGP Network Configuration14-11 Viewing the Neighbor Tab on the BGP Configuration Window 14-12 BGP Neighbor Information BGP Neighbor ConfigurationNeighbor Tab-Detailed Description 14-13 BGP Neighbor Configuration Window-Detailed Description 14-14 BGP Configuration Window-Redistribution Tab 14-15 BGP Redistribution Information BGP Redistribute ConfigurationRedistribution Tab-Detailed Description 14-16 BGP Redistribute Configuration-Detailed Description 14-17 Viewing the BGP Status Window BGP Status14-18 14-19 12 BGP Status-Network Tab 14-20 13 BGP Status-Neighbor Tab BGP General BGP Status Window-Detailed DescriptionBGP-Details BGP Information BGP Network Information NetworkNeighbor BGP Neighbor Information BGP Redistribution Information BGP Address-Family SynchronizationRedistribution 14-23 14-24 15 BGP Address-Family Synchronization Window 14-25 16 Action Report Synchronization Tab BGP Address Family ConfigurationBGP Address-Family Synchronization-Detailed Description 14-26 18 BGP Address-Family Configuration Window 14-27 BGP Address Family Information Configuring Address FamilyAF-General Tab-Detailed Description 14-28 Add Address Family Configure Address Family-Detailed Description14-29 Modifying BGP Address Family 14-30 Modify Address Family Parameters 14-31 21 BGP Address-Family Configuration Window-AF-Network Tab 14-32 Network Information BGP Address Family-Network ConfigurationAF-Network Tab-Detailed Description 14-33 Add/Remove Network 14-34 23 BGP Address-Family Configuration Window-AF-Neighbor Tab 14-35 Neighbor Information BGP Address Family-Neighbor ConfigurationAF-Neighbor Tab-Detailed Description 14-36 Add/Remove Neighbor 14-37 14-38 Redistribute Information AF-Redistribute Tab-Detailed Description14-39 BGP Address Family-Redistribute Configuration 14-40 Add/Remove Redistribution Information BGP Address-Family StatusViewing the BGP Address-Family Status window 14-41 14-42 27 BGP Address-Family Status Window 14-43 28 BGP Status-AF-Network Tab 14-44 29 BGP Status-AF-Neighbor Tab BGP Address Family Information BGP Address-Family Status Window-Detailed DescriptionAF-General 14-45 AF-Neighbor AF-NetworkAF-Redistribute Ospf Management Ospf ConfigurationViewing the Ospf Configuration Window 14-47 Config Config Tab-Detailed Description14-48 Adding an Ospf Process 14-49 Removing an Ospf Process 14-50 Ospf Network Viewing the Network Tab on the Ospf Configuration Window14-51 Configuring a Network 14-52 14-53 37 Action Report Ospf Status Configure Network-Detailed DescriptionConfigure Network Viewing the Ospf Status Window 14-55 39 Ospf Status Window 14-56 40 Ospf Status-Process Information Tab 14-57 41 Ospf Status-Area Tab 14-58 42 Ospf Status-Interface Tab 14-59 43 Ospf Status-Neighbor Tab 14-60 44 Ospf Status-Link State Tab General Group Ospf Status-Detailed Description14-61 Process Summary Process InformationArea Network Details Area Range InterfaceStub Area 14-63 Virtual Interface Interface Metric14-64 Virtual Neighbor Neighbor14-65 Lsdb Link StateHost Hosts Introduction 15-1 Mpls Management Workflow 15-2 Window/Task Menu Options to Select to Open Window Launching the Mpls Management Windows15-3 Viewing the Mpls Forwarding Information Window Mpls Forwarding Information15-4 Mpls Forwarding Information Tab Mpls Forwarding Information Window-Detailed Description15-5 Viewing the Mpls Interface Status Window Fault Management for Mpls LSR InterfacesMpls Interface Status 15-6 General Interface Configuration TabMpls Interface Status Window-Detailed Description 15-7 Viewing the Mpls Interface Information Window Mpls Interface Information15-8 Select Interface Interface Setup TabMpls Interface Information Window-Detailed Description 15-9 Mpls Setup Tab 15-10 Interface Performance Tab 15-11 Mpls Performance Tab 15-12 15-13 Mpls Interface Information Window-MPLS Performance Tab Viewing the Mpls Interface Performance Window Performance Management for Mpls LSR InterfacesMpls Interface Performance 15-14 Counters Mpls Interface Performance Window-Detailed DescriptionGeneral Performance Statistics Tab 15-15 High Speed Counters Mpls Performance Statistics Tab15-16 Outgoing Direction Incoming Direction15-17 Viewing the Mpls LDP Entity Status Window Fault Management for Mpls LDPMpls LDP Entity Status Window 15-18 Entity Tab Mpls LDP Entity Status Window-Detailed Description15-19 General LDP Status 15-20 Entity Statistics Entity Statistics Tab15-21 General Label Range Tab 15-22 General Label Range 15-23 ATM Parameters ATM Parameters Tab15-24 ATM Label Range ATM Label Range Tab15-25 Viewing the Mpls LDP Hello Adjacencies Window Mpls LDP Hello Adjacencies15-26 Hello Adjacencies Mpls LDP Hello Adjacencies Window-Detailed DescriptionHello Adjacencies Tab 15-27 Viewing the Mpls LDP Peer Status Window Mpls LDP Peer Status15-28 Sessions Tab Mpls LDP Peer Status Window-Detailed DescriptionPeers Tab LDP Peers LDP Sessions 15-30 LDP Session Statistics Session Statistics Tab15-31 LDP ATM Session ATM Sessions Tab15-32 Viewing the Mpls Tunnel Information Window Fault Management for Mpls Traffic EngineeringMpls Tunnel Information 15-33 Select Tunnel Tab Mpls Tunnel Information Window-Detailed Description15-34 Select Tunnel Head Tunnel Setup Tab15-35 Tunnel Info 15-36 Advanced Tunnel Status15-37 Head Tunnel Hops Tab 15-38 Hop Table LSP Setup Tab15-39 22 Mpls Tunnel Information Window-LSP Setup Tab 15-40 15-41 LSP Hops Tab 15-42 Computed HOP Table Actual Route HOP Table15-43 LSP Resource Tab 15-44 Tunnel Performance Performance TabResource Table 15-45 15-46 Introduction to VRF Management 16-1 Router Manager Window VRF Management WorkflowsLaunching the Mpls VRF Management Windows 16-2 Deploying VRF Objects Creating VRF Objects in the EM16-3 16-4 Deploying a VRF Object 16-5 Deployment Wizard Views 16-6 Object Selector Window 16-7 Deployment Wizard-Views Configuring and Creating a VRF Policy on a Selected Chassis Creating and Configuring the VRF Policy on a Device16-8 VRF Configuration Window 16-9 Deleting a Routing Target from a Selected Chassis Removing a VRF Policy from a Selected ChassisAdding a Routing Target to a Selected Chassis 16-10 VRF Configuration Window-Detailed Description VRF Configuration Tab Export Associating a VRF Policy with an InterfaceDevice Action Import Associating VRF Policies 16-13 VRF Tab Removing a VRF Policy from a Selected InterfaceVRF Association Window-Detailed Description Available VRF Policies Viewing the VRF Status Window VRF Fault ManagementVRF Status 16-15 VRF Details VRF Status Window-Detailed Description16-16 Performance and Security Tab 16-17 Security Performance16-18 Viewing the Interface VRF Status Window Interface VRF Status16-19 Interface VRF Association Tab Interface VRF Status Window-Detailed DescriptionVPN Status Viewing the VPN Status Window VPN Status Window-Detailed Description 16-21 VRF Routes Routes Tab16-22 Route Targets Tab 16-23 VRF Route Targets 16-24 Interface MPLS/EBGP Neighbor BGP Neighbor Tab16-25 Viewing the VRF Object Status Window VRF Object Status16-26 VRF Object Status Window-Detailed Description 16-27 Routes 16-28 16-29 Route Targets 16-30 Interface Association Interface Association Tab16-31 Performance Tab 16-32 Trap Alarm Description Severity Clears 17-1 17-2 Enabling/Disabling Traps on the Device 17-3 Traps Tab Mpls Trap Configuration Window-Detailed Description17-4 Launching the Mpls CLI Troubleshooting Services Windows Mpls CLI Troubleshooting Services17-5 Verify Routing Protocols 17-6 Verify Routing Tables 17-7 Verify CEF Switching 17-8 Verify CEF Switching Summary 17-9 Verify Mpls Interfaces 17-10 Verify Label Distribution 17-11 Verify Label Bindings 17-12 Verify Interface CEF Switching 17-13 17-14 Color Severity of Alarms Cisco 12000/10720 Router Manager Alarms18-1 Cisco 12000/10720 Router Trap Support Viewing Alarms18-2 Chassis Alarms 18-3 18-4 Syslog Traps Interface Alarms18-5 Trap Alarm Description Configuration Management Traps18-6 Operational Status Polling Heartbeat PollingConnectivity Management Disabling Heartbeat Polling Performance Logging 18-8 Change Management 19-1 Mismatched State Inserting a Line Card19-2 19-3 Line Card in Mismatched State Removing a Line Card 19-4 19-5 19-6 Performance Management and Historical Data 20-1 Monitored Attribute Description Viewing the Performance Manager Window20-2 Performance Manager window appears see Figure 20-3 Viewing Performance Statistics 20-4 Press Action Viewing a Chart20-5 Archiving Printing a Performance FileSaving Performance Data to a File 20-6 Monitored Attributes Exporting a Performance FilePerformance Manager Window-Detailed Description 20-7 Start Time PeriodSummary End Table Display Tab Line Chart TabRefresh 20-9 20-10 Configuration AdministrationAdministration What Version is the Software? What Dialogs Use the IOS CLI Instead of SNMP? 21-2 Verifying SNMP, Log, and Trap Settings Configuration21-3 Show running-config begin snmp 21-4 ATM IP Configuration GUI Display Error Settings BGP ConfigurationATM Sub-Interface Configuration 21-5 Viewing ATM Physical Port Configurations? 21-6 SONET/SDH Conversion Chart OL-4455-01 GUIs that Synchronize with the Device when Launched GUI Synchronization Details GUIs that do not Synchronize with the Device when Launched Network Diagram Setup Problem Analysis of Problem Solution Local Outgoing Prefix Bytes Tag Next Hop Running Configs Tag Tag or VC Or Tunnel Id Switched Interface PE1 No ip mroute-cache Interface POS4/0/0 Bandwidth Network 0.0.0.0 255.255.255.255 area Router bgp Interface GigabitEthernet1/0 Pvc test5 254/5 Pvc test6 254/6 Pvc test4 254/10 PE2 CE2 Redundancy No keepalive-enable Enable password atlantech OL-4455-01 APS IN-1 Clli IN-2 IN-3 IN-4 IN-5 IN-6