See Also „ set interface dhcp-clienton | HP Manager Software

display dhcp-server 183

Table 36 Output for display dhcp-client (continued)

Field	Description

Subnet Mask	Network mask of the IP address received from the
	DHCP server.

Default Gateway	Default gateway IP address received from the DHCP
	server. If the address is 0.0.0.0, the server did not
	provide an address.

DHCP Server	IP address of the DHCP server.

DNS Servers	DNS server IP address(es) received from the DHCP
	server.

DNS Domain Name	Default DNS domain name received from the DHCP
	server.

See Also

set interface dhcp-client on page 144

display dhcp-serverDisplays MSS DHCP server information.

Syntax — display dhcp-server [interface vlan-id] [verbose]

interface vlan-id— Displays the IP addresses leased by the specified VLAN.

verbose — Displays configuration and status information for the MSS DHCP server.

Defaults — None.

Access — All.

History —Introduced in MSS Version 4.0.

Examples — The following command displays the addresses leased by the MSS DHCP server:

WX-1200#display dhcp-server			MAC	Lease Remaining (sec)
VLAN	Name	Address	MAC	Lease Remaining (sec)
----	--------------	---------------	-----------------	--------------------
1	default	10.10.20.2	00:01:02:03:04:05	12345
1	default	10.10.20.3	00:01:03:04:06:07	2103
2	red-vlan	192.168.1.5	00:01:03:04:06:08	102
2	red-vlan	192.168.1.7	00:01:03:04:06:09	16789

Image 183

HP Manager Software manual See Also „ set interface dhcp-clienton, Display dhcp-serverDisplays MSS Dhcp server information

Contents

3CRWXR10095A, 3CRWX120695A, 3CRWX440095A Wireless LAN Mobility System 3Com Corporation 350 Campus Drive Marlborough, MA USA Contents Set system location Clear banner motd Clear history Clear prompt 104 102 126 Display ip alias 127 187 174 Set summertime 177 Set system ip-address 179180 Set timezone 181 Display dhcp-client 182 183 Display snmp community 186 245 267 MAP Access Point Commands by Usage272 Clear radio-profile 274 Clear service-profile 275 276 Set user group 258 Set usergroup 259 Set web-aaa 260 318 STP Commands 414 Security ACL Commands by Usage 423 clear security acl395 Set spantree portvlanpri 396 Set spantree priority 397 448 Crypto certificate 449 Commands by Usage 447Display security acl hits 430 Display security acl info 431 432 503 500 530 525525 Display rfdetect visible 526 528 Clear log trace 562 Clear trace Dir Display boot 547 Display config 548549 561 Register Your Product 607 System LOG CommandsPage List conventions that are used throughout this guide Conventions „ Wireless LAN Switch Manager 3WXM Release Notes „ Wireless LAN Switch and Controller Release NotesDocumentation „ Document part number and revision on the title CommentsPddtechpubscomments@3com.com „ Document title Example Overview Set enablepass Clear interface vlan-idipClear fdb dynamic port port-list vlan vlan-id Notation Text EntryConventions MAC Address User Globs MasksSubnet Masks Wildcard Masks Gives examples of user globs MAC Address GlobsUser Globs „ a single port number. For example WX1200# set port enableVlan Globs Matching Order for Globs Operating systems Command-LineWX1200# reset port Editing WX1200# display i Tab Using CLI Help At your access level, type the help command. For exampleWX1200# display i? WX1200# display ip telnet Understanding Command DescriptionsSet ap dap name command has the following complete syntax WX1200# display ip ? Usage Commands byDisable Syntax disable Defaults None Quit Enable Set enablepass Access Commands To located commands in this chapter based on their use System Service Commands „ display banner motd on Banner with an empty banner by typing the following commandClear banner motd Clear history Clear system Clear prompt Motd Display banner Display Base-information„ clear banner motd on See Also „ set license on Defaults None Access AllDisplay license Display system Display system output Describes the fields of display system output Nvram size /SDRAM size percent of total Syntax help WX switch„ Using CLI Help on Help „ clear history on Set auto-configHistory Syntax history Set auto-config Common Name remoteswitch1@example.com Enable the Dhcp client on VlanEnable the auto-config option WX-1200#crypto generate key admin 1024 key pair generated Save the configuration changes „ Delimiting character that begins and ends the messageSyntax set banner motd text Syntax set confirm on off Set confirmSee Also „ clear banner motd on „ display banner motd on That might have a large impact on the network WX4400# set confirm off Set lengthExamples To turn off these confirmation messages, type WX4400# clear vlan red Installs an upgrade license, for managing more MAPs Set licenseSee Also „ display license on Syntax set prompt string Set prompt Country Codes Set system contact Stores a contact name for the WX switchSet system Countrycode Country Code Country Codes WX1200# set system country code CA Ip-addressMobility Domain „ ip-addr- IP address, in dotted decimal notation Syntax set system name string Syntax set system location string Set system name System Service Commands Locate commands in this chapter based on their use Port Commands „ set dap on That are using the MAPClear dap Removes a Distributed MAP Syntax clear port-group name name Clear port-group„ name name Name of the port group See Also „ set port-groupon „ display port-groupon See Also „ display port status on „ set port name on Clear portPreference Clear port name Removes the name assigned to a port Port Clear port type„ display port preference on „ set port preference on Counters Display port Display port-groupShows port group information WX1200 display port counters octets portSyntax display port-group all name group-name Output for display port-group Describes the fields in the display port-group outputSee Also „ clear port-groupon „ set port-groupon Describes the fields in this display Display port Output for display port preference WX4400# display port preference Port PreferenceSyntax display port status port-list WX1200# display port status Output for display port status „ set port speed on Monitor portSee Also „ clear port type on „ set port negotiation on Key Controls for Monitor Port Counters Display WX4400# monitor port counters Output for monitor port counters Correct length but contained an invalid See Also „ display port counters on Set dap Reset port Port Commands Set dap Set port Following command removes Distributed MAPAdministratively disables or reenables a port Syntax set port enable disable port-list With no spaces See Also „ reset port onConfigured together as a single logical link Single logical link Syntax set port port name name Name or number in other CLI commandsSet port name See Also „ clear port-groupon „ display port-groupon WX1200# set port negotiation 2 enable Following command enables autonegotiation on portSyntax set port negotiation port-listenable disable WX1200# set port negotiation 3,5 disable Set port poe Access pointsFollowing command enables PoE on ports 4 See Also „ set port type ap on „ set port type wired-authon WX4400# set port preference 2 rj45 Set port speedChanges the speed of a port Syntax set port preference port-listrj45 Set port trap Set snmp profile command WX1200# set port trap 3-4 enable Mp-352mp-372- MAP access point model „ poe enable disable Power over Ethernet PoE state „ 11a 802.11a „ 11b 802.11b „ 11g 802.11g„ radiotype 11a 11b 11g Radio type Defaults All WX ports are network ports by default MAP Access Port Defaults WX1200# set port type ap 1-3,5 model ap3750 poe enableWX1200# set port type ap 1-3,5 model ap8250 poe enable Set port type Wired-authBefore changing the port type from ap to wired-author from Command Vlan membership Wired Authentication Port Details See Also „ clear port type on „ set port type ap on Port Commands Vlan Commands Clear fdb Deletes an entry from the forwarding database FDBSyntax clear fdb perm static dynamic Clear vlan „ display fdb onPort from the VLAN, make sure you specify the port number Displays entries in the forwarding database Following command completely removes Vlan marigoldSee Also „ set vlan port on „ display vlan config on Display fdb WX4400# display fdb all WX4400# display fdb Describes the fields in the display fdb outputSee Also „ clear fdb on Output for display fdb See Also „ set fdb agingtime on Agingtime Station Display roaming Describes the fields in the display See Also „ display roaming vlan onOutput for display roaming station Output for display roaming vlan Syntax display roaming vlanWX4400# display roaming vlan Syntax display tunnel See Also „ display vlan config onDisplay tunnel Output for display tunnel WX1200# display vlan config burgundy Display vlan configOutput for display vlan config Syntax display vlan config vlan-id Set fdb Adds a permanent or static entry to the forwarding databaseSyntax set fdb perm static Syntax set fdb agingtime vlan-idage seconds See Also „ clear fdb on „ display fdb on Syntax set vlan vlan-numname name Set vlan nameSee Also „ display fdb agingtime on Creates a Vlan and assigns a number and name to it Set vlan port Adds ports 1 through 3 to the Vlan Tag value to be the same but some other switches doSet vlan Tunnel-affinity See Also „ display roaming vlan on „ display vlan config on To locate commands in this chapter based on their use IP Services Commands DNS IP Services Commands by Usage Syntax clear interface vlan-idip Access Enabled History Introduced in MSS VersionClear interface Removes an IP interface Clear ip alias See Also „ display ip alias onSyntax clear ip alias name WX1200# clear ip dns domain Clear ip dns domain Removes the default DNS domain name„ ip-addr- IP address of a DNS server Syntax clear ip dns domain See Also „ display ip route on „ set ip route on Default is an alias for IP address 0.0.0.0/0Clear ip route „ clear ip dns domain on Clear ip telnet Defaults The default Telnet port number isTelnet management traffic to its default Removes an NTP server from a WX switch configuration Clear ntp Update-interval „ display snmp community on Clear snmpCommunity Syntax clear snmp community name comm-string Clear snmp usm Clear snmp profileClear snmp trap Receiver Syntax clear summertime See Also „ set snmp usm on „ display snmp usm on Use the address Clear timezone Syntax display arp ip-addr Display arpUsage All Shows the ARP table „ set arp on „ set arp agingtime onOutput for display arp Output for display interface Shows the IP aliases configured on the wireless LAN switchDisplay ip alias See Also „ set interface on „ set interface status on „ set ip alias on Examples The following command displays the DNS informationDisplay ip dns „ clear ip alias on Syntax display ip https Display ip httpsShows information about the Https management port Output for display ip dns WX4400# display ip https Output for display ip https WX4400# display ip route Display ip routeShows the IP route table Syntax display ip route destination FieldDescription Output of display ip route Output for display ip telnet Syntax display ip telnetWX4400 display ip telnet Output for display ntp Examples To display NTP information for a WX switch, typeDisplay ntp Shows NTP client information „ set ntp server on „ set summertime on „ set timezone on Display snmp ConfigurationShows Snmp settings on a wireless LAN switch Examples To display Snmp settings on a WX switch, type Output of display snmp configuration WX1200# display summertime Defaults There is no summertime offset by defaultSummertime Syntax display summertime WX1200# display timedate Syntax display timezoneWX4400# display timezone „ set timedate on „ set timezone on Defaults „ count „ traceroute on Set arp WX1200# set arp agingtime Following command disables ARP agingSee Also „ set arp agingtime on Syntax set arp agingtime seconds Set interface Syntax set interface vlan-idip dhcp-client enable disable Dhcp-client„ clear interface on Defaults The Dhcp server is enabled by default on a new Configures the MSS Dhcp server„ enable Enables the Dhcp server „ disable Disables the Dhcp server Syntax set interface vlan-idstatus up down See Also „ display dhcp-serveron See Also „ clear ip alias on „ display ip alias on Aliases as shortcuts in CLI commandsSet ip alias Set ip dns WX1200# set ip dns domain example.com Syntax set ip dns domain name Syntax set ip dns server ip-addrprimary secondary Set ip route WX switch is disabledSyntax set ip https server enable disable Syntax set ip route default ip-addr mask Set ip route Syntax set ip snmp server enable disable Secure Shell SSH management traffic WX4400# set ip snmp server enableSet ip ssh „ clear snmp notify target on „ set ip ssh server on Absolute-timeout„ set ip ssh absolute-timeouton „ set ip ssh idle-timeouton Idle-timeout Also disabledSet ip ssh server Telnet management traffic Maximum number of SSH sessions supported on a WX switch isSet ip telnet History -Introduced in MSS Version Syntax set ip telnet server enable disable Set ntp server Enables or disables the NTP client on a wireless LAN switchConfigures a wireless LAN switch to use an NTP server Set ntp NTP server RFC 1305, Network Time Protocol Version 3 SpecificationDefaults The default NTP update interval is 64 seconds Implementation and Analysis User. SNMPv3 does not use community strings Set snmp Set snmp community Set snmp notify TargetSNMPv3 with Informs Usm trap user username SNMPv3 with Traps SNMPv2c with Informs SNMPv1 with Traps SNMPv2c with Traps Success change accepted Snmp notification types „ notification-type- Any of the items in Table Point Snmp notification types WX-1200#set snmp notify profile snmpprofrfdetect send RFDetectRogueDisappearTraps success change accepted Syntax set snmp protocol v1 v2c usm all enable disable WX-1200# set snmp security encrypted success change accepted Community strings Versions, use the set snmp community command to configureSet snmp trap Set snmp usm „ auth-type none md5 sha auth-pass-phrase string IP Services Commands WX-1200# set snmp usm securesnmpmgr1 snmp-engine-id Auth-type sha auth-pass-phrase myauthpwordEncrypt-type 3des encrypt-pass-phrase mycryptpword WX1200# set summertime PDT success change accepted WX4400# set interface taupe ip 10.10.20.20/24 Following WX4400# set timedate date feb 29 2004 time 235800 Sets the time of day and date on the wireless LAN switchSet timedate Syntax set timedate date mmm dd yyyy time hhmmss It is enabled Set timezoneWX1200# set timezone PST Output for display dhcp-client Syntax display dhcp-clientWX-1200# display dhcp-client WX-1200#display dhcp-server See Also „ set interface dhcp-clientonDisplay dhcp-serverDisplays MSS Dhcp server information Syntax display dhcp-server interface vlan-id verbose Describe the fields in these displays Output for display dhcp-serverDisplay dhcp-server Output for display dhcp-client verbose See Also „ set interface dhcp-serveron WX-1200#display snmp community Displays the configured Snmp community stringsOutpot for display snmp community Syntax display snmp community Displays Snmp statistics counters Syntax display snmp countersWX-1200#display snmp counters WX-1200#display snmp notify profile Syntax display snmp notify profile See Also „ clear snmp profile on „ set snmp profile on Syntax display snmp notify targetWX-1200#display snmp notification target User Name of the Snmp user EngineID Output for display snmp notification target WX-1200#display snmp status Output for display Snmp status Switch has booted „ display snmp notify target on „ display snmp usm on Output for display snmp usmWX-1200#display snmp usm USM users See Also „ clear snmp usm on „ display snmp usm on Telnet Opens a Telnet client session with a remote deviceWX4400# telnet See Also „ clear sessions on „ display sessions on Defaults„ dnf Disabled Traceroute Ctrl+C „ no-dns- Disabled „ port„ queries „ size „ ttl „ wait „ ping on Error messages for traceroute Locate commands in this chapter based on their use This chapter presents AAA commands alphabetically. Use toAAA Commands by Usage Display accounting statistics on WX4400# clear accounting dot1x Nin Syntax clear accounting admin dot1x user-glob Admin Clear authentication Syntax clear authentication console user-glob WX4400# clear authentication console ReginaConsoleConsole Syntax clear authentication dot1x ssid ssid-namewired Syntax clear authentication mac ssid ssid-namewired Clear authentication Removes a MAC authentication rule. macSyntax clear authentication last-resort ssid ssid-namewired WX4400# clear authentication last-resort wired Access Enabled History -Introduced in MSS WX4400# clear authentication mac ssid thatcorp aabbccSyntax clear authentication proxy ssid ssid-nameuser-glob See Also „ set authentication proxy on „ on Clear authentication Removes a WebAAA rule. webWX-1200#clear authentication proxy ssid mycorp Syntax clear location policy rule-number Syntax clear mac-user mac-addr User who is authenticated by a MAC addressClear mac-user Radius server For your Radius server WX switch, for a user who is authenticated by a MAC addressGroup ACL from the profile of a user at MAC address Mac-usergroup Clear Mac-usergroup attr „ set mobility-profileon „ set mobility-profile mode onMobility-profile Clear user „ set user on Database on the WX switch, for a user with a passwordClear user attr Nin „ clear usergroup on Clear user groupClear usergroup Usergroup Syntax clear usergroup group-name attr attribute-name Time-Of-Day attribute from the group Displays all current AAA settingsSecion added to indicate the state of the WebAAA feature Display aaa Display aaa Output Describes the fields that can appear in display aaa output Display aaa Output Statistics output Stored in the local database on the WX switchDisplay accounting Statistics Display accounting statistics „ clear location policy on On an WX switchDisplay location Policy Admin console Set accountingAre sent Authenticated by MAC authentication Server when the user roamsAccesses the switch using Telnet or Web Manager Authenticated by Set accounting dot1x mac web Set authentication Set authentication admin Following methods in priority order. MSS applies multiple Through the switch’s consoleCompleting logon Globs on For more information, see Usage Syntax set authentication dot1x ssid ssid-namewired Set authentication dot1x AAA Commands Success change accepted Syntax set authentication last-resort 235 Syntax set authentication mac Set authentication mac Proxy Syntax set authentication web ssid ssid-namewired WX-1200#set authentication proxy ssid mycorp ** srvrgrp1 AAA Commands Set location policy For details, see Vlan Globs on Set location policy WX4400# set location policy deny if user eq *.theirfirm.com Tempvendora into Vlan kiosk1 Set mac-user See Also „ clear mac-useron „ display aaa on Authentication Attributes for Local Users Filter-id outboundacl.out Authentication Attributes for Local Users YY/MM/DD-HHMM Time-of-day WX4400# set mac-user 010203040506 attr filter-id acl-03.in Syntax set mac-usergroup See Also „ clear mac-user attr on „ display aaa on Syntax set mobility-profile name name port none all See Also „ clear mac-usergroup attr on „ display aaa on AAA Commands „ set user attr on „ set usergroup on Syntax set mobility-profile mode enable disable Set user Orange Set user attr29Jan04 „ clear user on Server That exists in the local database on the WX switchSet user group „ clear user attr on Assigns authorization attributes for the group To add a user to a group, user the command set user groupSet usergroup Examples To disable WebAAA, type the following command Syntax set web-aaa enable disableSet web-aaa Mobility Domain Commands by Usage To locate commands in this chapter based on their use Member Mobility-domain See Also „ set mobility-domain member on Display mobility-domain configDisplays the configuration of the Mobility Domain Status WX4400# display mobility-domain status Display mobility-domain Output Command is rejected SetSyntax set mobility-domain member ip-addr 192.168.1.8 Mode memberSeed, this command overwrites that configuration Seed-ip Syntax set mobility-domain mode seed domain-name Set mobility-domain mode seed domain-name Mobility Domain Commands Commands Type Command Set ap dap radio auto-tune max-power on Set ap dap radio auto-tunemin-client-rateon Clear ap dap RadioSyntax clear ap port-listdap dap-num radio 1 2 all WX1200# clear ap 3 radio Radio-Specific Parameters Syntax clear radio-profile name parameter Syntax clear service-profile name „ name Service profile name See Also „ clear radio-profileon „ set radio-profile mode on WX4400# display dap config WX1200# display ap config DAP Output for display ap config „ set port type ap on „ set ap dap bias on WX1200# display ap counters Tkip Pkt Replays Output for display ap counters Ccmp Pkt Replays See Also „ display sessions network on WX-1200#display dap qos-stats Output for display ap dap qos-stats Output of display ap etherstats Syntax display ap dap etherstats port-listdap-numWX4400# display dap etherstats Access point groups „ name Name of an MAP group or Distributed MAP groupSyntax display ap dap group name „ set ap dap group on Output for display ap groupWX1200# display ap group loadbalance1 WX4400# display dap status MAP WX1200# display ap status Output for display ap status Output for display ap status Syntax display auto-tune attributes Decide whether to change channel or power settingsDisplay auto-tune Attributes See Also „ display auto-tune neighbors on Output for display auto-tune attributesWX1200# display auto-tune attributes ap 2 radio Ap map-numradio 1 2all Neighbors3Com radio can hear Syntax display auto-tune neighbors Display auto-tune Neighbors ap 2 radio Output for display auto-tune neighbors Display dap global command Display dapConnection Output of display dap connection Dap connection serial-id M9DE48B6EAD00Syntax display dap global dap-numserial-id serial-ID WX4400# display dap global Output for display dap global Network port is a member of a Vlan UnconfiguredBut that are not configured on any WX switches Longer appears in the command’s output Syntax display radio-profile name ? Output for display dap unconfiguredRadio-profile Displays radio profile information Output for display radio-profile WX4400# display radio-profile default Tune Channel Ssid „ ? Displays a list of service profiles Service-profileDisplays service profile information „ name Displays information about the named service profile Display service-profile Other WPA parameters Reset ap dap Configurable Template Parameters for Distributed MAPs Dap auto mode enable commandUsage lists the configurable template parameters and their Listed in . The commands are listed in the See Also section WX1200# set dap auto success change accepted Syntax set dap auto mode enable disable See Also „ set dap auto on RadiotypeTemplate „ Radio type „ 11a-802.11a „ 11b-802.11b „ 11g-802.11g Syntax set ap port-listdap dap-numauto bias high low See Also „ display ap dap config on Syntax set dap num fingerprint hex Blink enable disable „ ap port-list- List of MAP access ports to add to the group WX1200# set ap 4 group none success change accepted Set ap dap name Changes an MAP name „ antennatype ANT5060 ANT5120 ANT5180 internal „ antennatype ANT1060 ANT1120 ANT1180 internal Radio 1 2 auto-tune max-power power-level Set ap dap radio auto-tune max-power Radio 1 2 auto-tune max-retransmissions retransmissions Set ap dap radio auto-tune max- retransmissions Set ap dap radio auto-tune max- retransmissions Set ap dap radio channel Sets an MAP radio’s channelSyntax set ap port-listdap dap-numradio 1 „ display ap dap config on Set ap dap radio auto-tune min-client-rateRadio 1 2 auto-tune min-client-rate rate Set ap 6 radio 1 min-client-rate Examples Radio 1 2 mode enable disable Set ap dap radio modeEnables or disables a radio on an MAP access point Following command enables radio 2 on ports 1 through Defaults None Sets an MAP radio’s transmit power Set ap dap radio tx-power Syntax set dap security require none optional WX-1200#set dap security require Set ap dap Upgrade-firmware 11g-only Set radio-profile Syntax set radio-profile name active-scan enable disable Set radio-profile auto-tune channel-config Syntax set radio-profile name auto-tune channel-holddown Set radio-profile auto-tune channel-holddown Syntax set radio-profile name auto-tune channel-interval Set radio-profile auto-tune channel-interval Syntax set radio-profile name auto-tune power-backoff-timer Set radio-profile auto-tune power-backoff- timer WX4400# set radio-profile rp2 auto-tune power-backoff-timer Set radio-profile auto-tune power-config Set radio-profile auto-tune power-interval Beacon-interval Following command disables countermeasures in radio profile Clients from being able to use rogue access points„ rogue Configures radios to attack rogues only Defaults Countermeasures are disabled by default Syntax set radio-profile name dtim-interval interval Syntax set radio-profile name long-retry threshold Syntax set radio-profile name frag-threshold threshold Syntax set radio-profile name max-rx-lifetime time Syntax set radio-profile name max-tx-lifetime time Mode Set radio-profile mode WX4400# set radio-profile rp1 mode enable Syntax set radio-profile name Syntax set radio-profile name rts-threshold threshold Syntax set radio-profile name service-profile name Parameter Default Value To Default Value Defaults for Service Profile Parameters Set radio-profile auth-psk command 349 Wmm Short-retry Syntax set service-profile Name auth-dot1x enable disable WPA IE Set service-profile auth-fallthru Syntax set service-profile name auth-psk enable disable Syntax set service-profile name beaconed enable disable Cipher-ccmp Set service-profile Cipher-tkip Cipher-wep104 Use the set service-profile wep commands Cipher-wep40 Syntax set service-profile name psk-phrase passphrase Syntax set service-profile name psk-raw hex Syntax set service-profile name rsn-ie enable disable See Also „ set service-profilecipher-ccmpon Syntax set service-profile name ssid-name ssid-name Set service-profile auth-psk command Syntax See Also „ set service-profilessid-typeon Syntax set service-profile name tkip-mc-time wait-time See Also „ set service-profilessid-nameon WX4400# mkdir corpa-ssid success change accepted Ssid managed by the service profileSyntax set service-profile name web-aaa-form url Web-aaa-form Set service-profile wep active-multicast- index „ copy on „ dir on„ mkdir on Syntax set service-profile name wep active-unicast-index num Set service-profile wep active-unicast- index Wep key-index Syntax set service-profile name wpa-ie enable disable STP Commands by Table to locate commands in this chapter based on their useSTP Commands by Usage Syntax clear spantree portcost port-list STP root bridge in all VLANs on a WX switchClear spantree Portcost „ set spantree portpri on PortpriPortvlancost „ clear spantree portvlanpri on „ clear spantree portcost on Portvlanpri See Also „ display spantree statistics on „ clear spantree portpri on Syntax display spantree Spantree vlan default Root Output for display spantree „ display spantree blockedports on Or disabledDisplay spantree Backbonefast Blockedports „ set spantree backbonefast onSee Also „ display spantree on Output for display spantree portfast PortfastFor one or more network ports See Also „ set spantree portfast on Syntax display spantree statistics Port’s VLANs„ port-list- List of ports Syntax display spantree portvlancost port-list WX4400# display spantree statistics Topology change Timer value Hold timer Vlan Vlan ID Output for display spantree statistics Configpending Switch is the root or is attempting to become the root Syntax display spantree uplinkfast vlan vlan-id See Also „ clear spantree statistics on „ set spantree uplinkfast on Set spantree An indirect link Examples The following command enables STP on all VLANsConfigured on a WX switch Following command disables STP on Vlan burgundy „ display spantree backbonefast on Fwddelay „ all Changes the maximum age on all VLANs Issues a topology change messageMaxage VLANs to 4 seconds 65,535. STP selects lower-cost paths over higher-cost paths Type. lists the defaults for STP port path costSTP Port Path Cost Defaults Path to the STP root bridge Portvlancost command Syntax set spantree portpri port-listpriority value See Also „ display spantree portfast on To 20 in Vlan mauve Bridge for a specific Vlan on a wireless LAN switch„ all Changes the cost on all VLANs Type. See on „ all Changes the priority on all VLANs Path to the STP root bridge, on one Vlan or all VLANsPorts Highest priority through 255 lowest priority Uplinkfast Priority See Also „ display spantree uplinkfast on Igmp Commands by Usage Igmp Snooping Commands Clear igmp statistics Display igmpSee Also display igmp statistics on TTL Output for display igmp TTL Mrouter Syntax display igmp mrouter vlan vlan-idWX1200# display igmp Mrouter vlan orange Defaults None Access Enabled Only one querierSyntax display igmp querier vlan vlan-id WX1200# display igmp querier vlan red WX1200# display igmp querier vlan defaultOutput for display igmp mrouter WX1200# display igmp querier vlan orange „ set igmp querier on Receiver-table See Also „ set igmp receiver on Output for display igmp receiver-tableIgmp Receiver-table group 237.255.255.0/24 WX1200# display igmp statistics vlan orange Shows Igmp statistics„ vlan vlan-id Vlan name or number. If you do not specify a Syntax display igmp statistics vlan vlan-id From the multicast routers in the subnet Output of display igmp statistics See Also „ set igmp rv on Wireless LAN switch From 1 through 65,535 VLANs on a wireless LAN switchVLAN, the timer change applies to all VLANs Set igmp lmqi See Also „ display igmp statistics on Syntax set igmp mrouter port port-listenable disable See Also „ set igmp mrsol mrsi on Enables or disables multicast router solicitation by a WXSyntax set igmp mrsol enable disable vlan vlan-id Set igmp mrsol Syntax set igmp oqi seconds vlan vlan-id Set igmp oqiSee Also „ set igmp mrsol on All VLANs on a WX „ set igmp qri on Set igmpProxy-report „ set igmp lmqi on Syntax set igmp qi seconds vlan vlan-id Set igmp qi Set igmp qri VLANs on a WXGroup. You can specify a value from 1 through 65,535 Syntax set igmp querier enable disable vlan vlan-id Syntax set igmp receiver port port-listenable disableSee Also „ display igmp querier on Set igmp rv Set igmp rv Igmp Snooping Commands Security ACL Security ACL Commands Syntax clear security acl acl-name all editbuffer-index WX4400# commit security acl acl133 configuration accepted Syntax clear security acl map acl-nameall vlan vlan-id Syntax commit security acl acl-nameall WX4400# commit security acl all WX4400# display security aclSyntax display security acl dscp Syntax display security acl editbuffer Examples The following command displays the tableSee Also „ set security acl on WX-1200#display security acl dscp Syntax display security acl hits WX4400# display security acl editbuffer See Also „ hit-sample-rateon „ set security acl on WX4400# display security acl hitsSyntax display security acl info acl-nameall editbuffer Syntax display security acl map acl-name Display security aclMap Security ACL is assigned WX4400# display security acl map acl111 Resource-usageACL acl111 is mapped Support for your Product on WX4400# display security acl resource-usage Output of display security acl resource-usage Output of display security acl resource-usage Hit-sample-rate Packets filtered by the security ACL or hitsSyntax hit-sample-rate seconds Syntax rollback security acl acl-nameall Protocol, or IP, ICMP, TCP, or UDP packet information Set security acl By Icmp packets By TCP packetsBy UDP packets „ ip „ tcp „ udp „ icmp Security ACL Commands Set security acl WX4400# set security acl ip acl123 deny 192.168.2.11 Set security acl map Security ACL Commands Cryptography Commands by Usage To locate commands in this chapter based on their use Syntax crypto ca-certificate admin eap webaaa See Also „ display crypto ca-certificateon Syntax crypto certificate admin eap webaaa Access Enabled History -Introduced in MSS Version See Also display crypto key ssh on Syntax crypto generate key admin eap ssh webaaa 512 1024 Syntax crypto generate request admin eap webaaa Email Address admin@example.com WX4400# crypto generate request admin See Also „ crypto certificate on „ crypto generate key on Syntax crypto generate self-signed admin eap webaaa WX4400# crypto generate self-signed admin Crypto otp „ crypto pkcs12 on Crypto pkcs12 WX4400# crypto otp eap hap9iN#ss See Also „ crypto otp on Display crypto ca-certificate Output Display cryptoCa-certificate Pkcs #7 certificate Describes the fields of the display On the WX switchSyntax display crypto certificate admin eap webaaa Certificate Syntax display crypto key ssh See Also crypto generate key on Cryptography Commands Radius Commands by Usage Locate commands in this chapter based on their uses Clear radius Syntax clear radius client system-ip See Also „ display aaa on „ set radius client system-ipon Syntax clear radius proxy port all See Also „ set radius proxy client onSee Also „ set radius proxy port on Syntax clear radius proxy client all See Also „ display aaa on „ set radius server on Syntax clear radius server server-nameSyntax clear server group group-nameload-balance „ set server group on Set radius Set radius client System-ip„ clear radius server on WX4400# set radius client system-ipsuccess change accepted Set radius proxy Port„ clear radius proxy client on To 32 characters long, with no spaces or tabs Set radius server WX1200# set server group shorebirds members heron egret Load-balance group „ group-name- Server group name of up to 32 charactersSandpiper Radius and Server Group Commands Performance On the switchCommands on 802.1X Commands by Usage See Also „ display dot1x on „ set dot1x bonded-periodon Resets the Bonded Auth period to its default valueClear dot1x Bonded-period „ set dot1x max-reqon Port-control Quiet-period See Also „ display dot1x on „ set dot1x reauth-periodon Reauth-maxReauth-period „ set dot1x reauth-maxon Supplicant „ set dot1x timeout auth-serveron„ set dot1x timeout supplicant on Auth-server Tx-period Display dot1x„ set dot1x tx-periodon WX4400# display dot1x clients WX1200# display dot1x config Type the following command to display 802.1X statistics Explains the counters in the display dot1x stats outputWX4400# display dot1x stats Port-control command Set dot1xAuthcontrol Machine to start reauthentication for the user Authentication is enabledExamples To enable per-port 802.1X authentication on wired Authentication ports, type the following command See Also „ display dot1x on „ clear dot1x bonded-periodon Syntax set dot1x key-tx enable disable See Also „ clear dot1x max-reqon „ display dot1x on See Also „ display dot1x on See Also „ display port status on „ display dot1x on Authentication dot1X command To a supplicant after a failed authentication Syntax set dot1x reauth enable disableSyntax set dot1x quiet-period seconds Before the supplicant client becomes unauthorized See Also „ display dot1x on „ clear dot1x reauth-maxonSyntax set dot1x reauth-max number-of-attempts See Also „ display dot1x on „ clear dot1x reauth-periodon Set dot1x timeoutAttempts reauthentication Out a request to a Radius authentication server Out an authentication session with a supplicant client Syntax set dot1x timeout supplicant secondsSyntax set dot1x tx-period seconds Broadcast and multicast encryption keys Syntax set dot1X wep-rekey enable disableWep-rekey See Also „ display dot1x on „ clear dot1x tx-periodon To 300 seconds Defaults The default is 1800 seconds 30 minutesWep-rekey-period „ seconds Specify a value between 30 and 1,641,600 19 days Telnet sessions Clear sessions VLANs, or session ID Network To clear session 9, type the following command WX4400# clear sessions network mac-addrWX1200# clear sessions network session-id Display sessions WX4400 display sessions admin WX4400 display sessions consoleWX4400 display sessions telnet Display sessions telnet client Output See Also „ clear sessions on Syntax display sessions network WX1200# display sessions network mac-addr 00055d7e981a „ Summary display See on „ Verbose display See on„ display sessions network session-id display See on WX1200# display sessions network WX1200# display sessions network session-id WX1200# display sessions network verbose Additional display sessions network verbose Output Display sessions network summary Output Time Display sessions network session-id Output 802.1X protocol on a wired authentication port See Also „ clear sessions network on Session Management Commands RF Detection Commands by Usage To locate the commands in this chapter based on their use Removes a MAC address from the attack list Examples The following command clears MAC addressClear rfdetect Attack-list Black-list Countermeasures Mac Clear rfdetectIgnore „ set rfdetect ssid-liston Ssid-list„ display rfdetect ignore on „ set rfdetect ignore on „ display rfdetect vendor-liston Vendor-listDisplay rfdetect „ set rfdetect vendor-liston RF Detection Commands Display rfdetect countermeasures Output CountermeasuresMobility Domain Domain Displays information about the APs detected by a WX switch DataSyntax display rfdetect data WX1200# display rfdetect data Display rfdetect data Output Ignore list Syntax display rfdetect ignoreWX4400# display rfdetect ignore Total number of entries WS1200# display rfdetect mobility-domain Bssid mac-addr Displays rogues that are using the specifiedDuring RF detection scans Syntax display rfdetect mobility-domain WS1200# display rfdetect mobility-domain ssid 3Com-webaaa Ssid 3Com-webaaa Following command displays detailed information for a Bssid Display rfdetect mobility-domain OutputWX1200# display rfdetect mobility-domain bssid 000b0e0004d1 Display rfdetect mobility-domain ssid or bssid Output „ clear rfdetect ssid-liston WX switch„ display rfdetect data on Displays the entries in the permitted Ssid list Visible Display ap dap status command WX1200# display rfdetect visible Radio Display rfdetect visible Output Set rfdetect Active-scanAddresses of APs and clients Configured. WX switches do not share client black lists Configured. WX switches do not share attack listsExamples The following command adds MAC address Defaults The client black list is empty by default Countermeasures Mac Set rfdetect ignore Set rf detect See Also „ display log buffer on Signature WX switches in a Mobility Domain Device’s OUI is in the permitted vendor list Examples The following command adds Ssid mycorp to the listOnly for the SSIDs that are on the list Permitted SSIDs Trailing 000000 value is required Syntax display rfdetect attack-listWX1200# display rfdetect attack-list WX1200# display rfdetect black-list Displays the wireless clients detected by an WX switchClients Syntax display rfdetect black-list WX1200# display rfdetect Clients Display rfdetect clients Output Display rfdetect clients mac Output From the wired side of the network addressed to File Management Commands „ tftp/ip-addr/filename- Name of the archive file to create Dir command outputLocally on the switch Tape archive tar format Syntax clear boot config „ Copies a file from a Tftp server to nonvolatile storage „ reset system onCopy Performs the following copy operations WX4400# copy floorwx tftp//10.1.1.1/floorwx WX4400# copy test-config new-config Syntax delete url File or the running configurationDelete Immediately deletes the specified file Dir Describes the fields in the dir output „ copy on „ delete onOutput for dir Describes the fields in the display boot output Display bootReboot and configured for use after the next reboot Access Access Display config Displays the configuration running on the WX switchSyntax display config area area all Display version See Also „ load config on „ save config onAnd, optionally, for any attached MAP access points WX4400# display config area vlan WX1200# display version details WX1200# display version Output for display version Load configRunning configuration with the commands in the loaded file Describes the fields in the display version output WX4400# load config testconfig1 Following command loads configuration file testconfig1Syntax load config url WX4400# load config Creates a new subdirectory in nonvolatile storage Mkdir Reset system Restarts an WX switch and reboots the software„ dir on „ rmdir on Generate new key pairs and certificates on the switch Restore Removes a subdirectory from nonvolatile storage „ backup onWX1200# restore system tftp/10.10.20.9/sysabak Rmdir „ dir on „ mkdir on Save configSaves the running configuration to a configuration file Syntax save config filename Testconfig1 Set bootConfiguration-file Configuration Syntax set boot partition boot0 boot1 File Management Commands Trace Commands Deletes the log messages stored in the trace buffer Deletes running trace commands and ends trace processesClear log trace Clear trace WX4400# display trace WX switch, or all possible trace optionsDisplay trace Syntax display trace all Authentication Save traceSet trace See Also „ clear trace on „ display trace on Authorization Set trace dot1x Syntax set trace sm mac-addr mac-address port port-num Set trace sm Trace Commands Snoop Commands Clear snoop Clear snoop map„ display snoop info on „ display snoop map on Set snoop„ set snoop map on „ display snoop on Chapter Snoop Commands WX1200# set snoop snoop1 observer 10.10.30.2 snap-length Radio 2 of the MAP. This option does not apply to Set snoop mapFilter Radio 1 of the MAP All snoop filters Set snoop modeTo an MAP radio and enable the filter Enable stop-afternum-pkts- Enables the snoop filter Displays the MAP radio mapping for all snoop filters Display snoop map commandFor all snoop filters configured on a WX switch Display snoop WX1200# display snoop info snoop1 Display snoop info Shows the configured snoop filtersSee Also „ clear snoop on Syntax display snoop filter-name Examples display snoop stats filter-namedap-numradio Snoop map snoop1 Snoop1 Display snoop stats OutputSnoop stats snoop1 Chapter Snoop Commands Syntax clear log buffer server ip-addr Clear log See Also „ clear log trace on You can view event messages archived in the buffer Log buffer facility ?WX4400# display log buffer facility AAA „ set log on „ clear log on „ display log config onLog config „ clear log on Syntax display log trace +-/number-of-messages Address in dotted decimal notation Set logStorage „ console Sets log parameters for console sessions „ trace Sets log parameters for trace files See Also See Also „ display log config on Set log traceMbytes System LOG Commands Boot Prompt Boot Prompt Commands Autoboot „ FN=filename System image filename Boot„ BT=type Boot type „ DEV=device Location of the system image file „ change on „ display on Syntax change Change Syntax create Create Syntax delete Usage When you type the delete command, the next-lowerExamples To remove the currently active boot profile, type Profiles, see display on Syntax diag Diag Syntax display Defaults None „ change on „ create on „ delete on „ next on Output of display command Fver „ ls on For an individual command„ command-name- Boot prompt command Displays a list of the boot prompt commands Syntax next Next Command at the boot prompt ResetResets a WX switch’s hardware Syntax reset Test „ on Enables the poweron test flag„ OFF Disables the poweron test flag Defaults The poweron test flag is disabled by default Syntax version Dir or fver commandType the following command at the boot prompt Version Purchase ServicesRegister Your Product Downloads Access SoftwareTroubleshoot Online Contact Us Latsupportanc@3com.com Country Telephone Number Index Delete 544, 597 diag Dir 545, 598 disable 33 display Index Index Index Traceroute Version