See Also „ crypto otp on | HP Manager Software specs

458CHAPTER 13: CRYPTOGRAPHY COMMANDS

webaaa — Unpacks a PKCS #12 object file for a WebAAA certificate and key pair — and optionally the certificate authority’s own certificate — for authenticating the WX switch to WebAAA clients.

file-location-url— Location of the PKCS #12 object file to be installed. Specify a location of between 1 and 128 alphanumeric characters, with no spaces.

Defaults — The password you enter with the crypto otp command must be the same as the one protecting the PKCS #12 file.

Access — Enabled.

History —Introduced in MSS Version 3.0.

Usage — To use this command, you must have already created a one-time password with the crypto otp command.

You must also have the PKCS #12 object file available. You can download a PKCS #12 object file via TFTP from a remote location to the local nonvolatile storage system on the WX switch.

Examples — The following commands copy a PKCS #12 object file for an EAP certificate and key pair—and optionally the certificate authority’s own certificate—from a TFTP server to nonvolatile storage on the WX switch, create the one-time password hap9iN#ss, and unpack the PKCS #12 file:

WX4400# copy tftp://192.168.253.1/2048full.p12 2048full.p12 success: received 637 bytes in 0.253 seconds [ 2517 bytes/sec]

WX4400# crypto otp eap hap9iN#ss

OTP set

WX4400# crypto pkcs12 eap 2048full.p12 Unwrapped from PKCS12 file:

keypair

device certificate CA certificate

See Also

crypto otp on page 456

Image 458

HP Manager Software manual See Also „ crypto otp on, WX4400# crypto otp eap hap9iN#ss

Contents

Wireless LAN Mobility System 3CRWXR10095A, 3CRWX120695A, 3CRWX440095A 3Com Corporation 350 Campus Drive Marlborough, MA USA Contents Clear banner motd Clear history Clear prompt Set system location 102 104 126 Display ip alias 127 183 Display snmp community 186 174 Set summertime 177 Set system ip-address 179180 Set timezone 181 Display dhcp-client 182 187 245 Set user group 258 Set usergroup 259 Set web-aaa 260 MAP Access Point Commands by Usage272 Clear radio-profile 274 Clear service-profile 275 276 267 318 STP Commands Set spantree portvlanpri 396 Set spantree priority 397 Security ACL Commands by Usage 423 clear security acl395 414 432 Commands by Usage 447Display security acl hits 430 Display security acl info 431 448 Crypto certificate 449 500 503 528 525525 Display rfdetect visible 526 530 561 Dir Display boot 547 Display config 548549 Clear log trace 562 Clear trace System LOG Commands Register Your Product 607Page Conventions List conventions that are used throughout this guide Documentation „ Wireless LAN Switch Manager 3WXM Release Notes„ Wireless LAN Switch and Controller Release Notes „ Document title CommentsPddtechpubscomments@3com.com „ Document part number and revision on the title Example Overview Clear fdb dynamic port port-list vlan vlan-id Set enablepassClear interface vlan-idip MAC Address Text EntryConventions Notation Wildcard Masks MasksSubnet Masks User Globs User Globs Gives examples of user globsMAC Address Globs Matching Order for Globs WX1200# set port enableVlan Globs „ a single port number. For example Editing Command-LineWX1200# reset port Operating systems WX1200# display i Tab WX1200# display i? Using CLI HelpAt your access level, type the help command. For example WX1200# display ip ? Understanding Command DescriptionsSet ap dap name command has the following complete syntax WX1200# display ip telnet Syntax disable Defaults None Commands byDisable Usage Enable Quit Set enablepass Access Commands System Service Commands To located commands in this chapter based on their use Clear history Banner with an empty banner by typing the following commandClear banner motd „ display banner motd on Clear prompt Clear system Display banner Motd „ clear banner motd on DisplayBase-information Display system Defaults None Access AllDisplay license See Also „ set license on Describes the fields of display system output Display system output Nvram size /SDRAM size percent of total Help WX switch„ Using CLI Help on Syntax help Syntax history Set auto-configHistory „ clear history on Set auto-config WX-1200#crypto generate key admin 1024 key pair generated Enable the Dhcp client on VlanEnable the auto-config option Common Name remoteswitch1@example.com Syntax set banner motd text Save the configuration changes„ Delimiting character that begins and ends the message That might have a large impact on the network Set confirmSee Also „ clear banner motd on „ display banner motd on Syntax set confirm on off WX4400# clear vlan red Set lengthExamples To turn off these confirmation messages, type WX4400# set confirm off See Also „ display license on Installs an upgrade license, for managing more MAPsSet license Set prompt Syntax set prompt string Countrycode Set system contact Stores a contact name for the WX switchSet system Country Codes Country Code Country Codes „ ip-addr- IP address, in dotted decimal notation Ip-addressMobility Domain WX1200# set system country code CA Syntax set system location string Syntax set system name string Set system name System Service Commands Port Commands Locate commands in this chapter based on their use Removes a Distributed MAP That are using the MAPClear dap „ set dap on See Also „ set port-groupon „ display port-groupon Clear port-group„ name name Name of the port group Syntax clear port-group name name Clear port name Removes the name assigned to a port Clear portPreference See Also „ display port status on „ set port name on „ set port preference on Clear port type„ display port preference on Port Display port Counters Syntax display port-group all name group-name Display port-groupShows port group informationWX1200 display port counters octets port Describes the fields in this display Describes the fields in the display port-group outputSee Also „ clear port-groupon „ set port-groupon Output for display port-group Display port Syntax display port status port-list Output for display port preferenceWX4400# display port preference Port Preference Output for display port status WX1200# display port status „ set port negotiation on Monitor portSee Also „ clear port type on „ set port speed on Key Controls for Monitor Port Counters Display Output for monitor port counters WX4400# monitor port counters Correct length but contained an invalid See Also „ display port counters on Reset port Set dap Port Commands Set dap Syntax set port enable disable port-list Following command removes Distributed MAPAdministratively disables or reenables a port Set port Single logical link See Also „ reset port onConfigured together as a single logical link With no spaces See Also „ clear port-groupon „ display port-groupon Name or number in other CLI commandsSet port name Syntax set port port name name WX1200# set port negotiation 3,5 disable Following command enables autonegotiation on portSyntax set port negotiation port-listenable disable WX1200# set port negotiation 2 enable See Also „ set port type ap on „ set port type wired-authon Access pointsFollowing command enables PoE on ports 4 Set port poe Syntax set port preference port-listrj45 Set port speedChanges the speed of a port WX4400# set port preference 2 rj45 Set snmp profile command Set port trap Mp-352mp-372- MAP access point model WX1200# set port trap 3-4 enable „ radiotype 11a 11b 11g Radio type „ poe enable disable Power over Ethernet PoE state„ 11a 802.11a „ 11b 802.11b „ 11g 802.11g Defaults All WX ports are network ports by default WX1200# set port type ap 1-3,5 model ap8250 poe enable MAP Access Port DefaultsWX1200# set port type ap 1-3,5 model ap3750 poe enable Command Wired-authBefore changing the port type from ap to wired-author from Set port type Wired Authentication Port Details Vlan membership See Also „ clear port type on „ set port type ap on Port Commands Vlan Commands Syntax clear fdb perm static dynamic Clear fdbDeletes an entry from the forwarding database FDB Port from the VLAN, make sure you specify the port number Clear vlan„ display fdb on Display fdb Following command completely removes Vlan marigoldSee Also „ set vlan port on „ display vlan config on Displays entries in the forwarding database WX4400# display fdb all Output for display fdb Describes the fields in the display fdb outputSee Also „ clear fdb on WX4400# display fdb Agingtime See Also „ set fdb agingtime on Display roaming Station Output for display roaming station Describes the fields in the displaySee Also „ display roaming vlan on WX4400# display roaming vlan Output for display roaming vlanSyntax display roaming vlan Output for display tunnel See Also „ display vlan config onDisplay tunnel Syntax display tunnel Syntax display vlan config vlan-id Display vlan configOutput for display vlan config WX1200# display vlan config burgundy Syntax set fdb perm static Set fdbAdds a permanent or static entry to the forwarding database See Also „ clear fdb on „ display fdb on Syntax set fdb agingtime vlan-idage seconds Creates a Vlan and assigns a number and name to it Set vlan nameSee Also „ display fdb agingtime on Syntax set vlan vlan-numname name Set vlan port Tunnel-affinity Tag value to be the same but some other switches doSet vlan Adds ports 1 through 3 to the Vlan See Also „ display roaming vlan on „ display vlan config on IP Services Commands To locate commands in this chapter based on their use IP Services Commands by Usage DNS Removes an IP interface Access Enabled History Introduced in MSS VersionClear interface Syntax clear interface vlan-idip Syntax clear ip alias name Clear ip aliasSee Also „ display ip alias on Syntax clear ip dns domain Clear ip dns domain Removes the default DNS domain name„ ip-addr- IP address of a DNS server WX1200# clear ip dns domain „ clear ip dns domain on Default is an alias for IP address 0.0.0.0/0Clear ip route See Also „ display ip route on „ set ip route on Removes an NTP server from a WX switch configuration Defaults The default Telnet port number isTelnet management traffic to its default Clear ip telnet Update-interval Clear ntp Syntax clear snmp community name comm-string Clear snmpCommunity „ display snmp community on Receiver Clear snmp profileClear snmp trap Clear snmp usm See Also „ set snmp usm on „ display snmp usm on Syntax clear summertime Clear timezone Use the address Shows the ARP table Display arpUsage All Syntax display arp ip-addr Output for display arp „ set arp on„ set arp agingtime on See Also „ set interface on „ set interface status on Shows the IP aliases configured on the wireless LAN switchDisplay ip alias Output for display interface „ clear ip alias on Examples The following command displays the DNS informationDisplay ip dns „ set ip alias on Output for display ip dns Display ip httpsShows information about the Https management port Syntax display ip https Output for display ip https WX4400# display ip https Syntax display ip route destination Display ip routeShows the IP route table WX4400# display ip route Output of display ip route FieldDescription WX4400 display ip telnet Output for display ip telnetSyntax display ip telnet Shows NTP client information Examples To display NTP information for a WX switch, typeDisplay ntp Output for display ntp „ set ntp server on „ set summertime on „ set timezone on Examples To display Snmp settings on a WX switch, type ConfigurationShows Snmp settings on a wireless LAN switch Display snmp Output of display snmp configuration Syntax display summertime Defaults There is no summertime offset by defaultSummertime WX1200# display summertime WX4400# display timezone WX1200# display timedateSyntax display timezone Defaults „ count „ set timedate on „ set timezone on Set arp „ traceroute on Syntax set arp agingtime seconds Following command disables ARP agingSee Also „ set arp agingtime on WX1200# set arp agingtime Set interface „ clear interface on Syntax set interface vlan-idip dhcp-client enable disableDhcp-client „ disable Disables the Dhcp server Configures the MSS Dhcp server„ enable Enables the Dhcp server Defaults The Dhcp server is enabled by default on a new See Also „ display dhcp-serveron Syntax set interface vlan-idstatus up down Set ip dns Aliases as shortcuts in CLI commandsSet ip alias See Also „ clear ip alias on „ display ip alias on Syntax set ip dns domain name WX1200# set ip dns domain example.com Syntax set ip dns server ip-addrprimary secondary Syntax set ip route default ip-addr mask WX switch is disabledSyntax set ip https server enable disable Set ip route Set ip route Syntax set ip snmp server enable disable „ clear snmp notify target on WX4400# set ip snmp server enableSet ip ssh Secure Shell SSH management traffic „ set ip ssh idle-timeouton Absolute-timeout„ set ip ssh absolute-timeouton „ set ip ssh server on Set ip ssh server Idle-timeoutAlso disabled History -Introduced in MSS Version Maximum number of SSH sessions supported on a WX switch isSet ip telnet Telnet management traffic Syntax set ip telnet server enable disable Set ntp Enables or disables the NTP client on a wireless LAN switchConfigures a wireless LAN switch to use an NTP server Set ntp server Implementation and Analysis RFC 1305, Network Time Protocol Version 3 SpecificationDefaults The default NTP update interval is 64 seconds NTP server Set snmp User. SNMPv3 does not use community strings Set snmp community SNMPv3 with Informs Set snmp notifyTarget SNMPv3 with Traps Usm trap user username SNMPv2c with Informs SNMPv2c with Traps SNMPv1 with Traps Success change accepted „ notification-type- Any of the items in Table Snmp notification types Point Snmp notification types WX-1200#set snmp notify profile snmpprofrfdetect send RFDetectRogueDisappearTraps success change accepted Syntax set snmp protocol v1 v2c usm all enable disable WX-1200# set snmp security encrypted success change accepted Set snmp usm Versions, use the set snmp community command to configureSet snmp trap Community strings „ auth-type none md5 sha auth-pass-phrase string IP Services Commands Encrypt-type 3des encrypt-pass-phrase mycryptpword WX-1200# set snmp usm securesnmpmgr1 snmp-engine-idAuth-type sha auth-pass-phrase myauthpword WX1200# set summertime PDT success change accepted Following WX4400# set interface taupe ip 10.10.20.20/24 Syntax set timedate date mmm dd yyyy time hhmmss Sets the time of day and date on the wireless LAN switchSet timedate WX4400# set timedate date feb 29 2004 time 235800 WX1200# set timezone PST It is enabledSet timezone WX-1200# display dhcp-client Output for display dhcp-clientSyntax display dhcp-client Syntax display dhcp-server interface vlan-id verbose See Also „ set interface dhcp-clientonDisplay dhcp-serverDisplays MSS Dhcp server information WX-1200#display dhcp-server Display dhcp-server Describe the fields in these displaysOutput for display dhcp-server See Also „ set interface dhcp-serveron Output for display dhcp-client verbose Syntax display snmp community Displays the configured Snmp community stringsOutpot for display snmp community WX-1200#display snmp community WX-1200#display snmp counters Displays Snmp statistics countersSyntax display snmp counters Syntax display snmp notify profile WX-1200#display snmp notify profile WX-1200#display snmp notification target See Also „ clear snmp profile on „ set snmp profile onSyntax display snmp notify target Output for display snmp notification target User Name of the Snmp user EngineID Output for display Snmp status WX-1200#display snmp status Switch has booted WX-1200#display snmp usm USM users „ display snmp notify target on „ display snmp usm onOutput for display snmp usm See Also „ clear snmp usm on „ display snmp usm on WX4400# telnet TelnetOpens a Telnet client session with a remote device Traceroute Defaults„ dnf Disabled See Also „ clear sessions on „ display sessions on „ wait „ no-dns- Disabled „ port„ queries „ size „ ttl Ctrl+C Error messages for traceroute „ ping on AAA Commands by Usage Locate commands in this chapter based on their useThis chapter presents AAA commands alphabetically. Use to Display accounting statistics on Syntax clear accounting admin dot1x user-glob WX4400# clear accounting dot1x Nin Clear authentication Admin ConsoleConsole Syntax clear authentication console user-globWX4400# clear authentication console Regina Syntax clear authentication dot1x ssid ssid-namewired WX4400# clear authentication last-resort wired Clear authentication Removes a MAC authentication rule. macSyntax clear authentication last-resort ssid ssid-namewired Syntax clear authentication mac ssid ssid-namewired Syntax clear authentication proxy ssid ssid-nameuser-glob Access Enabled History -Introduced in MSSWX4400# clear authentication mac ssid thatcorp aabbcc WX-1200#clear authentication proxy ssid mycorp See Also „ set authentication proxy on„ on Clear authentication Removes a WebAAA rule. web Syntax clear location policy rule-number Radius server User who is authenticated by a MAC addressClear mac-user Syntax clear mac-user mac-addr ACL from the profile of a user at MAC address WX switch, for a user who is authenticated by a MAC addressGroup For your Radius server Clear Mac-usergroup Mac-usergroup attr Clear user „ set mobility-profile mode onMobility-profile „ set mobility-profileon Nin Database on the WX switch, for a user with a passwordClear user attr „ set user on Usergroup Clear user groupClear usergroup „ clear usergroup on Syntax clear usergroup group-name attr attribute-name Display aaa Displays all current AAA settingsSecion added to indicate the state of the WebAAA feature Time-Of-Day attribute from the group Describes the fields that can appear in display aaa output Display aaa Output Display aaa Output Statistics Stored in the local database on the WX switchDisplay accounting Statistics output Display accounting statistics Policy On an WX switchDisplay location „ clear location policy on Are sent Admin consoleSet accounting Authenticated by Server when the user roamsAccesses the switch using Telnet or Web Manager Authenticated by MAC authentication Set accounting dot1x mac web Set authentication Set authentication admin Globs on Through the switch’s consoleCompleting logon Following methods in priority order. MSS applies multiple For more information, see Usage Syntax set authentication dot1x ssid ssid-namewired Set authentication dot1x AAA Commands Success change accepted Syntax set authentication last-resort 235 Syntax set authentication mac Set authentication mac Proxy WX-1200#set authentication proxy ssid mycorp ** srvrgrp1 Syntax set authentication web ssid ssid-namewired AAA Commands Set location policy For details, see Vlan Globs on Set location policy WX4400# set location policy deny if user eq *.theirfirm.com Set mac-user Tempvendora into Vlan kiosk1 See Also „ clear mac-useron „ display aaa on Authentication Attributes for Local Users Authentication Attributes for Local Users Filter-id outboundacl.out YY/MM/DD-HHMM Time-of-day WX4400# set mac-user 010203040506 attr filter-id acl-03.in See Also „ clear mac-user attr on „ display aaa on Syntax set mac-usergroup See Also „ clear mac-usergroup attr on „ display aaa on Syntax set mobility-profile name name port none all AAA Commands Syntax set mobility-profile mode enable disable „ set user attr on „ set usergroup on Set user „ clear user on Set user attr29Jan04 Orange „ clear user attr on That exists in the local database on the WX switchSet user group Server Set usergroup Assigns authorization attributes for the groupTo add a user to a group, user the command set user group Set web-aaa Examples To disable WebAAA, type the following commandSyntax set web-aaa enable disable To locate commands in this chapter based on their use Mobility Domain Commands by Usage Mobility-domain Member Status Display mobility-domain configDisplays the configuration of the Mobility Domain See Also „ set mobility-domain member on Display mobility-domain Output WX4400# display mobility-domain status Syntax set mobility-domain member ip-addr Command is rejectedSet Seed-ip Mode memberSeed, this command overwrites that configuration 192.168.1.8 Set mobility-domain mode seed domain-name Syntax set mobility-domain mode seed domain-name Mobility Domain Commands Commands Type Command Set ap dap radio auto-tune max-power on Set ap dap radio auto-tunemin-client-rateon Syntax clear ap port-listdap dap-num radio 1 2 all Clear ap dapRadio Radio-Specific Parameters WX1200# clear ap 3 radio Syntax clear radio-profile name parameter „ name Service profile name Syntax clear service-profile name See Also „ clear radio-profileon „ set radio-profile mode on WX1200# display ap config WX4400# display dap config Output for display ap config DAP „ set port type ap on „ set ap dap bias on WX1200# display ap counters Output for display ap counters Tkip Pkt Replays See Also „ display sessions network on Ccmp Pkt Replays Output for display ap dap qos-stats WX-1200#display dap qos-stats WX4400# display dap etherstats Output of display ap etherstatsSyntax display ap dap etherstats port-listdap-num Syntax display ap dap group name Access point groups„ name Name of an MAP group or Distributed MAP group WX1200# display ap group loadbalance1 „ set ap dap group onOutput for display ap group MAP WX4400# display dap status Output for display ap status WX1200# display ap status Output for display ap status Attributes Decide whether to change channel or power settingsDisplay auto-tune Syntax display auto-tune attributes WX1200# display auto-tune attributes ap 2 radio See Also „ display auto-tune neighbors onOutput for display auto-tune attributes Syntax display auto-tune neighbors Neighbors3Com radio can hear Ap map-numradio 1 2all Output for display auto-tune neighbors Display auto-tune Neighbors ap 2 radio Connection Display dap global commandDisplay dap Syntax display dap global dap-numserial-id serial-ID Output of display dap connectionDap connection serial-id M9DE48B6EAD00 Output for display dap global WX4400# display dap global Longer appears in the command’s output UnconfiguredBut that are not configured on any WX switches Network port is a member of a Vlan Displays radio profile information Output for display dap unconfiguredRadio-profile Syntax display radio-profile name ? WX4400# display radio-profile default Output for display radio-profile Tune Channel Ssid „ name Displays information about the named service profile Service-profileDisplays service profile information „ ? Displays a list of service profiles Display service-profile Other WPA parameters Reset ap dap Listed in . The commands are listed in the See Also section Dap auto mode enable commandUsage lists the configurable template parameters and their Configurable Template Parameters for Distributed MAPs WX1200# set dap auto success change accepted Syntax set dap auto mode enable disable „ Radio type „ 11a-802.11a „ 11b-802.11b „ 11g-802.11g RadiotypeTemplate See Also „ set dap auto on Syntax set ap port-listdap dap-numauto bias high low See Also „ display ap dap config on Blink enable disable Syntax set dap num fingerprint hex „ ap port-list- List of MAP access ports to add to the group WX1200# set ap 4 group none success change accepted Set ap dap name Changes an MAP name „ antennatype ANT1060 ANT1120 ANT1180 internal „ antennatype ANT5060 ANT5120 ANT5180 internal Set ap dap radio auto-tune max-power Radio 1 2 auto-tune max-power power-level Set ap dap radio auto-tune max- retransmissions Radio 1 2 auto-tune max-retransmissions retransmissions Set ap dap radio auto-tune max- retransmissions Syntax set ap port-listdap dap-numradio 1 Set ap dap radio channelSets an MAP radio’s channel Radio 1 2 auto-tune min-client-rate rate „ display ap dap config onSet ap dap radio auto-tune min-client-rate Examples Set ap 6 radio 1 min-client-rate Following command enables radio 2 on ports 1 through Set ap dap radio modeEnables or disables a radio on an MAP access point Radio 1 2 mode enable disable Defaults None Set ap dap radio tx-power Sets an MAP radio’s transmit power Syntax set dap security require none optional WX-1200#set dap security require Upgrade-firmware Set ap dap Set radio-profile 11g-only Set radio-profile auto-tune channel-config Syntax set radio-profile name active-scan enable disable Set radio-profile auto-tune channel-holddown Syntax set radio-profile name auto-tune channel-holddown Set radio-profile auto-tune channel-interval Syntax set radio-profile name auto-tune channel-interval Set radio-profile auto-tune power-backoff- timer Syntax set radio-profile name auto-tune power-backoff-timer Set radio-profile auto-tune power-config WX4400# set radio-profile rp2 auto-tune power-backoff-timer Set radio-profile auto-tune power-interval Beacon-interval Defaults Countermeasures are disabled by default Clients from being able to use rogue access points„ rogue Configures radios to attack rogues only Following command disables countermeasures in radio profile Syntax set radio-profile name dtim-interval interval Syntax set radio-profile name frag-threshold threshold Syntax set radio-profile name long-retry threshold Syntax set radio-profile name max-rx-lifetime time Syntax set radio-profile name max-tx-lifetime time Mode Set radio-profile mode WX4400# set radio-profile rp1 mode enable Syntax set radio-profile name Syntax set radio-profile name service-profile name Syntax set radio-profile name rts-threshold threshold Defaults for Service Profile Parameters Parameter Default Value To Default Value Set radio-profile auth-psk command 349 Short-retry Wmm Syntax set service-profile Name auth-dot1x enable disable WPA IE Set service-profile auth-fallthru Syntax set service-profile name auth-psk enable disable Syntax set service-profile name beaconed enable disable Set service-profile Cipher-ccmp Cipher-tkip Use the set service-profile wep commands Cipher-wep104 Cipher-wep40 Syntax set service-profile name psk-phrase passphrase Syntax set service-profile name psk-raw hex See Also „ set service-profilecipher-ccmpon Syntax set service-profile name rsn-ie enable disable Set service-profile auth-psk command Syntax set service-profile name ssid-name ssid-name See Also „ set service-profilessid-typeon Syntax See Also „ set service-profilessid-nameon Syntax set service-profile name tkip-mc-time wait-time Web-aaa-form Ssid managed by the service profileSyntax set service-profile name web-aaa-form url WX4400# mkdir corpa-ssid success change accepted „ mkdir on Set service-profile wep active-multicast- index„ copy on „ dir on Set service-profile wep active-unicast- index Syntax set service-profile name wep active-unicast-index num Wep key-index Syntax set service-profile name wpa-ie enable disable STP Commands by Usage STP Commands byTable to locate commands in this chapter based on their use Portcost STP root bridge in all VLANs on a WX switchClear spantree Syntax clear spantree portcost port-list „ clear spantree portvlanpri on PortpriPortvlancost „ set spantree portpri on Portvlanpri „ clear spantree portcost on „ clear spantree portpri on See Also „ display spantree statistics on Spantree vlan default Syntax display spantree Output for display spantree Root Backbonefast Or disabledDisplay spantree „ display spantree blockedports on See Also „ display spantree on Blockedports„ set spantree backbonefast on See Also „ set spantree portfast on PortfastFor one or more network ports Output for display spantree portfast Syntax display spantree portvlancost port-list Port’s VLANs„ port-list- List of ports Syntax display spantree statistics WX4400# display spantree statistics Topology change Timer value Hold timer Output for display spantree statistics Vlan Vlan ID Configpending Switch is the root or is attempting to become the root See Also „ clear spantree statistics on Syntax display spantree uplinkfast vlan vlan-id Set spantree „ set spantree uplinkfast on Following command disables STP on Vlan burgundy Examples The following command enables STP on all VLANsConfigured on a WX switch An indirect link Fwddelay „ display spantree backbonefast on VLANs to 4 seconds Issues a topology change messageMaxage „ all Changes the maximum age on all VLANs Path to the STP root bridge Type. lists the defaults for STP port path costSTP Port Path Cost Defaults 65,535. STP selects lower-cost paths over higher-cost paths Portvlancost command See Also „ display spantree portfast on Syntax set spantree portpri port-listpriority value Type. See on Bridge for a specific Vlan on a wireless LAN switch„ all Changes the cost on all VLANs To 20 in Vlan mauve Highest priority through 255 lowest priority Path to the STP root bridge, on one Vlan or all VLANsPorts „ all Changes the priority on all VLANs Priority Uplinkfast See Also „ display spantree uplinkfast on Igmp Snooping Commands Igmp Commands by Usage See Also display igmp statistics on Clear igmp statisticsDisplay igmp TTL Output for display igmp TTL WX1200# display igmp Mrouter vlan orange MrouterSyntax display igmp mrouter vlan vlan-id Syntax display igmp querier vlan vlan-id Defaults None Access EnabledOnly one querier WX1200# display igmp querier vlan orange WX1200# display igmp querier vlan defaultOutput for display igmp mrouter WX1200# display igmp querier vlan red Receiver-table „ set igmp querier on Igmp Receiver-table group 237.255.255.0/24 See Also „ set igmp receiver onOutput for display igmp receiver-table Syntax display igmp statistics vlan vlan-id Shows Igmp statistics„ vlan vlan-id Vlan name or number. If you do not specify a WX1200# display igmp statistics vlan orange Output of display igmp statistics From the multicast routers in the subnet Wireless LAN switch See Also „ set igmp rv on Set igmp lmqi VLANs on a wireless LAN switchVLAN, the timer change applies to all VLANs From 1 through 65,535 Syntax set igmp mrouter port port-listenable disable See Also „ display igmp statistics on Set igmp mrsol Enables or disables multicast router solicitation by a WXSyntax set igmp mrsol enable disable vlan vlan-id See Also „ set igmp mrsol mrsi on All VLANs on a WX Set igmp oqiSee Also „ set igmp mrsol on Syntax set igmp oqi seconds vlan vlan-id „ set igmp lmqi on Set igmpProxy-report „ set igmp qri on Set igmp qi Syntax set igmp qi seconds vlan vlan-id Group. You can specify a value from 1 through 65,535 Set igmp qriVLANs on a WX See Also „ display igmp querier on Syntax set igmp querier enable disable vlan vlan-idSyntax set igmp receiver port port-listenable disable Set igmp rv Set igmp rv Igmp Snooping Commands Security ACL Commands Security ACL Syntax clear security acl acl-name all editbuffer-index WX4400# commit security acl acl133 configuration accepted Syntax clear security acl map acl-nameall vlan vlan-id Syntax commit security acl acl-nameall Syntax display security acl dscp WX4400# commit security acl allWX4400# display security acl WX-1200#display security acl dscp Examples The following command displays the tableSee Also „ set security acl on Syntax display security acl editbuffer WX4400# display security acl editbuffer Syntax display security acl hits Syntax display security acl info acl-nameall editbuffer See Also „ hit-sample-rateon „ set security acl onWX4400# display security acl hits Security ACL is assigned Display security aclMap Syntax display security acl map acl-name Support for your Product on Resource-usageACL acl111 is mapped WX4400# display security acl map acl111 WX4400# display security acl resource-usage Output of display security acl resource-usage Output of display security acl resource-usage Syntax hit-sample-rate seconds Hit-sample-ratePackets filtered by the security ACL or hits Syntax rollback security acl acl-nameall Set security acl Protocol, or IP, ICMP, TCP, or UDP packet information By UDP packets By Icmp packetsBy TCP packets „ ip „ tcp „ udp „ icmp Security ACL Commands Set security acl WX4400# set security acl ip acl123 deny 192.168.2.11 Set security acl map Security ACL Commands To locate commands in this chapter based on their use Cryptography Commands by Usage Syntax crypto ca-certificate admin eap webaaa Syntax crypto certificate admin eap webaaa See Also „ display crypto ca-certificateon Access Enabled History -Introduced in MSS Version Syntax crypto generate key admin eap ssh webaaa 512 1024 See Also display crypto key ssh on Syntax crypto generate request admin eap webaaa WX4400# crypto generate request admin Email Address admin@example.com Syntax crypto generate self-signed admin eap webaaa See Also „ crypto certificate on „ crypto generate key on WX4400# crypto generate self-signed admin Crypto otp Crypto pkcs12 „ crypto pkcs12 on See Also „ crypto otp on WX4400# crypto otp eap hap9iN#ss Pkcs #7 certificate Display cryptoCa-certificate Display crypto ca-certificate Output Certificate On the WX switchSyntax display crypto certificate admin eap webaaa Describes the fields of the display See Also crypto generate key on Syntax display crypto key ssh Cryptography Commands Locate commands in this chapter based on their uses Radius Commands by Usage Clear radius See Also „ display aaa on „ set radius client system-ipon Syntax clear radius client system-ip Syntax clear radius proxy client all See Also „ set radius proxy client onSee Also „ set radius proxy port on Syntax clear radius proxy port all Syntax clear server group group-nameload-balance See Also „ display aaa on „ set radius server onSyntax clear radius server server-name Set radius „ set server group on „ clear radius server on Set radius clientSystem-ip WX4400# set radius client system-ipsuccess change accepted „ clear radius proxy client on Set radius proxyPort To 32 characters long, with no spaces or tabs Set radius server WX1200# set server group shorebirds members heron egret Sandpiper Load-balance group„ group-name- Server group name of up to 32 characters Radius and Server Group Commands 802.1X Commands by Usage On the switchCommands on Performance Bonded-period Resets the Bonded Auth period to its default valueClear dot1x See Also „ display dot1x on „ set dot1x bonded-periodon Port-control „ set dot1x max-reqon Quiet-period „ set dot1x reauth-maxon Reauth-maxReauth-period See Also „ display dot1x on „ set dot1x reauth-periodon Auth-server „ set dot1x timeout auth-serveron„ set dot1x timeout supplicant on Supplicant „ set dot1x tx-periodon Tx-periodDisplay dot1x WX1200# display dot1x config WX4400# display dot1x clients WX4400# display dot1x stats Type the following command to display 802.1X statisticsExplains the counters in the display dot1x stats output Authcontrol Port-control commandSet dot1x Authentication ports, type the following command Authentication is enabledExamples To enable per-port 802.1X authentication on wired Machine to start reauthentication for the user Syntax set dot1x key-tx enable disable See Also „ display dot1x on „ clear dot1x bonded-periodon See Also „ display dot1x on See Also „ clear dot1x max-reqon „ display dot1x on Authentication dot1X command See Also „ display port status on „ display dot1x on Syntax set dot1x quiet-period seconds To a supplicant after a failed authenticationSyntax set dot1x reauth enable disable Syntax set dot1x reauth-max number-of-attempts Before the supplicant client becomes unauthorizedSee Also „ display dot1x on „ clear dot1x reauth-maxon Out a request to a Radius authentication server Set dot1x timeoutAttempts reauthentication See Also „ display dot1x on „ clear dot1x reauth-periodon Syntax set dot1x tx-period seconds Out an authentication session with a supplicant clientSyntax set dot1x timeout supplicant seconds See Also „ display dot1x on „ clear dot1x tx-periodon Syntax set dot1X wep-rekey enable disableWep-rekey Broadcast and multicast encryption keys „ seconds Specify a value between 30 and 1,641,600 19 days Defaults The default is 1800 seconds 30 minutesWep-rekey-period To 300 seconds Clear sessions Telnet sessions Network VLANs, or session ID WX1200# clear sessions network session-id To clear session 9, type the following commandWX4400# clear sessions network mac-addr Display sessions WX4400 display sessions telnet WX4400 display sessions adminWX4400 display sessions console See Also „ clear sessions on Display sessions telnet client Output Syntax display sessions network WX1200# display sessions network „ Summary display See on „ Verbose display See on„ display sessions network session-id display See on WX1200# display sessions network mac-addr 00055d7e981a WX1200# display sessions network verbose WX1200# display sessions network session-id Display sessions network summary Output Additional display sessions network verbose Output Time 802.1X protocol on a wired authentication port Display sessions network session-id Output See Also „ clear sessions network on Session Management Commands To locate the commands in this chapter based on their use RF Detection Commands by Usage Attack-list Examples The following command clears MAC addressClear rfdetect Removes a MAC address from the attack list Ignore Black-listCountermeasures Mac Clear rfdetect „ set rfdetect ignore on Ssid-list„ display rfdetect ignore on „ set rfdetect ssid-liston „ set rfdetect vendor-liston Vendor-listDisplay rfdetect „ display rfdetect vendor-liston RF Detection Commands Domain CountermeasuresMobility Domain Display rfdetect countermeasures Output Syntax display rfdetect data Displays information about the APs detected by a WX switchData Display rfdetect data Output WX1200# display rfdetect data WX4400# display rfdetect ignore Total number of entries Ignore listSyntax display rfdetect ignore Syntax display rfdetect mobility-domain Bssid mac-addr Displays rogues that are using the specifiedDuring RF detection scans WS1200# display rfdetect mobility-domain Ssid 3Com-webaaa WS1200# display rfdetect mobility-domain ssid 3Com-webaaa WX1200# display rfdetect mobility-domain bssid 000b0e0004d1 Following command displays detailed information for a BssidDisplay rfdetect mobility-domain Output Display rfdetect mobility-domain ssid or bssid Output Displays the entries in the permitted Ssid list WX switch„ display rfdetect data on „ clear rfdetect ssid-liston Display ap dap status command Visible Display rfdetect visible Output WX1200# display rfdetect visible Radio Addresses of APs and clients Set rfdetectActive-scan Defaults The client black list is empty by default Configured. WX switches do not share attack listsExamples The following command adds MAC address Configured. WX switches do not share client black lists Set rf detect Countermeasures Mac Set rfdetect ignore See Also „ display log buffer on WX switches in a Mobility Domain Signature Permitted SSIDs Examples The following command adds Ssid mycorp to the listOnly for the SSIDs that are on the list Device’s OUI is in the permitted vendor list WX1200# display rfdetect attack-list Trailing 000000 value is requiredSyntax display rfdetect attack-list Syntax display rfdetect black-list Displays the wireless clients detected by an WX switchClients WX1200# display rfdetect black-list Display rfdetect clients Output WX1200# display rfdetect Clients Display rfdetect clients mac Output From the wired side of the network addressed to File Management Commands Tape archive tar format Dir command outputLocally on the switch „ tftp/ip-addr/filename- Name of the archive file to create Syntax clear boot config Performs the following copy operations „ reset system onCopy „ Copies a file from a Tftp server to nonvolatile storage WX4400# copy test-config new-config WX4400# copy floorwx tftp//10.1.1.1/floorwx Immediately deletes the specified file File or the running configurationDelete Syntax delete url Dir Output for dir Describes the fields in the dir output„ copy on „ delete on Access Access Display bootReboot and configured for use after the next reboot Describes the fields in the display boot output Syntax display config area area all Display configDisplays the configuration running on the WX switch WX4400# display config area vlan See Also „ load config on „ save config onAnd, optionally, for any attached MAP access points Display version WX1200# display version WX1200# display version details Describes the fields in the display version output Load configRunning configuration with the commands in the loaded file Output for display version WX4400# load config Following command loads configuration file testconfig1Syntax load config url WX4400# load config testconfig1 Mkdir Creates a new subdirectory in nonvolatile storage „ dir on „ rmdir on Reset systemRestarts an WX switch and reboots the software Restore Generate new key pairs and certificates on the switch Rmdir „ backup onWX1200# restore system tftp/10.10.20.9/sysabak Removes a subdirectory from nonvolatile storage Syntax save config filename Save configSaves the running configuration to a configuration file „ dir on „ mkdir on Configuration Set bootConfiguration-file Testconfig1 Syntax set boot partition boot0 boot1 File Management Commands Trace Commands Clear trace Deletes running trace commands and ends trace processesClear log trace Deletes the log messages stored in the trace buffer Syntax display trace all WX switch, or all possible trace optionsDisplay trace WX4400# display trace Set trace AuthenticationSave trace Authorization See Also „ clear trace on „ display trace on Set trace dot1x Set trace sm Syntax set trace sm mac-addr mac-address port port-num Trace Commands Snoop Commands „ display snoop info on Clear snoopClear snoop map „ display snoop on Set snoop„ set snoop map on „ display snoop map on Chapter Snoop Commands WX1200# set snoop snoop1 observer 10.10.30.2 snap-length Radio 1 of the MAP Set snoop mapFilter Radio 2 of the MAP. This option does not apply to Enable stop-afternum-pkts- Enables the snoop filter Set snoop modeTo an MAP radio and enable the filter All snoop filters Display snoop Display snoop map commandFor all snoop filters configured on a WX switch Displays the MAP radio mapping for all snoop filters Syntax display snoop filter-name Display snoop info Shows the configured snoop filtersSee Also „ clear snoop on WX1200# display snoop info snoop1 Snoop map snoop1 Examples display snoop stats filter-namedap-numradio Snoop stats snoop1 Snoop1Display snoop stats Output Chapter Snoop Commands Clear log Syntax clear log buffer server ip-addr See Also „ clear log trace on WX4400# display log buffer facility AAA You can view event messages archived in the bufferLog buffer facility ? „ clear log on „ display log config onLog config „ set log on „ clear log on Syntax display log trace +-/number-of-messages „ console Sets log parameters for console sessions Set logStorage Address in dotted decimal notation „ trace Sets log parameters for trace files See Also Mbytes See Also „ display log config onSet log trace System LOG Commands Boot Prompt Commands Boot Prompt Autoboot „ DEV=device Location of the system image file Boot„ BT=type Boot type „ FN=filename System image filename „ change on „ display on Change Syntax change Create Syntax create Profiles, see display on Usage When you type the delete command, the next-lowerExamples To remove the currently active boot profile, type Syntax delete Diag Syntax diag Syntax display Defaults None Output of display command „ change on „ create on „ delete on „ next on Fver Displays a list of the boot prompt commands For an individual command„ command-name- Boot prompt command „ ls on Next Syntax next Syntax reset ResetResets a WX switch’s hardware Command at the boot prompt Defaults The poweron test flag is disabled by default „ on Enables the poweron test flag„ OFF Disables the poweron test flag Test Version Dir or fver commandType the following command at the boot prompt Syntax version Product ServicesRegister Your Purchase Online Access SoftwareTroubleshoot Downloads Contact Us Country Telephone Number Latsupportanc@3com.com Index Delete 544, 597 diag Dir 545, 598 disable 33 display Index Index Index Traceroute Version