Display accounting, Statistics | HP Manager Software manual

220CHAPTER 7: AAA COMMANDS

set authentication last-resorton page 234

set authentication mac on page 236

set authentication web on page 239

display accounting	Displays the AAA accounting records for wireless users. The records are
statistics	stored in the local database on the WX switch.
	(To display RADIUS accounting records, see the documentation for your
	RADIUS server.)
	Syntax — display accounting statistics
	Defaults — None.
	Access — Enabled.
	History —Introduced in MSS Version 3.0.
	Examples — To display the locally stored accounting records, type the
	following command:
	WX4400# display accounting statistics
	Sep 26 11:01:48 Acct-Status-Type=START Acct-Authentic=2
	User-Name=geetha AAA_TTY_ATTR=2 Event-Timestamp=1064599308
	Sept 26 12:50:21 Acct-Status-Type=STOP Acct-Authentic=2
	User-Name=geetha AAA_TTY_ATTR=2 Acct-Session-Time=6513
	Event-Timestamp=1064605821 Acct-Output-Octets=332
	Acct-Input-Octets=61
	Sep 26 12:50:33 Acct-Status-Type=START Acct-Authentic=2
	User-Name=geetha AAA_TTY_ATTR=2 Event-Timestamp=1064605833
	Table 46 describes the fields that can appear in display accounting
	statistics output.
	Table 46 display accounting statistics Output

	Field	Description

	Date and time	Date and time of the accounting record.

Image 220

HP Manager Software manual Display accounting, Stored in the local database on the WX switch, Statistics output

Contents

Wireless LAN Mobility System 3CRWXR10095A, 3CRWX120695A, 3CRWX440095A 3Com Corporation 350 Campus Drive Marlborough, MA USA Contents Clear banner motd Clear history Clear prompt Set system location 102 104 126 Display ip alias 127 174 Set summertime 177 Set system ip-address 179 180 Set timezone 181 Display dhcp-client 182183 Display snmp community 186 187 245 MAP Access Point Commands by Usage 272 Clear radio-profile 274 Clear service-profile 275 276Set user group 258 Set usergroup 259 Set web-aaa 260 267 318 STP Commands Security ACL Commands by Usage 423 clear security acl 395Set spantree portvlanpri 396 Set spantree priority 397 414 Commands by Usage 447 Display security acl hits 430 Display security acl info 431432 448 Crypto certificate 449 500 503 525 525 Display rfdetect visible 526528 530 Dir Display boot 547 Display config 548 549561 Clear log trace 562 Clear trace System LOG Commands Register Your Product 607Page Conventions List conventions that are used throughout this guide „ Wireless LAN Switch and Controller Release Notes „ Wireless LAN Switch Manager 3WXM Release NotesDocumentation Comments Pddtechpubscomments@3com.com„ Document title „ Document part number and revision on the title Example Overview Clear interface vlan-idip Set enablepassClear fdb dynamic port port-list vlan vlan-id Text Entry ConventionsMAC Address Notation Masks Subnet MasksWildcard Masks User Globs MAC Address Globs Gives examples of user globsUser Globs WX1200# set port enable Vlan GlobsMatching Order for Globs „ a single port number. For example Command-Line WX1200# reset portEditing Operating systems WX1200# display i Tab At your access level, type the help command. For example Using CLI HelpWX1200# display i? Understanding Command Descriptions Set ap dap name command has the following complete syntaxWX1200# display ip ? WX1200# display ip telnet Commands by DisableSyntax disable Defaults None Usage Enable Quit Set enablepass Access Commands System Service Commands To located commands in this chapter based on their use Banner with an empty banner by typing the following command Clear banner motdClear history „ display banner motd on Clear prompt Clear system Display banner Motd Base-information Display„ clear banner motd on Defaults None Access All Display licenseDisplay system See Also „ set license on Describes the fields of display system output Display system output Nvram size /SDRAM size percent of total WX switch „ Using CLI Help onHelp Syntax help Set auto-config HistorySyntax history „ clear history on Set auto-config Enable the Dhcp client on Vlan Enable the auto-config optionWX-1200#crypto generate key admin 1024 key pair generated Common Name remoteswitch1@example.com „ Delimiting character that begins and ends the message Save the configuration changesSyntax set banner motd text Set confirm See Also „ clear banner motd on „ display banner motd onThat might have a large impact on the network Syntax set confirm on off Set length Examples To turn off these confirmation messages, typeWX4400# clear vlan red WX4400# set confirm off Set license Installs an upgrade license, for managing more MAPsSee Also „ display license on Set prompt Syntax set prompt string Set system contact Stores a contact name for the WX switch Set systemCountrycode Country Codes Country Code Country Codes Ip-address Mobility Domain„ ip-addr- IP address, in dotted decimal notation WX1200# set system country code CA Syntax set system location string Syntax set system name string Set system name System Service Commands Port Commands Locate commands in this chapter based on their use That are using the MAP Clear dapRemoves a Distributed MAP „ set dap on Clear port-group „ name name Name of the port groupSee Also „ set port-groupon „ display port-groupon Syntax clear port-group name name Clear port PreferenceClear port name Removes the name assigned to a port See Also „ display port status on „ set port name on Clear port type „ display port preference on„ set port preference on Port Display port Counters WX1200 display port counters octets port Display port-groupShows port group informationSyntax display port-group all name group-name Describes the fields in the display port-group output See Also „ clear port-groupon „ set port-grouponDescribes the fields in this display Output for display port-group Display port WX4400# display port preference Port Preference Output for display port preferenceSyntax display port status port-list Output for display port status WX1200# display port status Monitor port See Also „ clear port type on„ set port negotiation on „ set port speed on Key Controls for Monitor Port Counters Display Output for monitor port counters WX4400# monitor port counters Correct length but contained an invalid See Also „ display port counters on Reset port Set dap Port Commands Set dap Following command removes Distributed MAP Administratively disables or reenables a portSyntax set port enable disable port-list Set port See Also „ reset port on Configured together as a single logical linkSingle logical link With no spaces Name or number in other CLI commands Set port nameSee Also „ clear port-groupon „ display port-groupon Syntax set port port name name Following command enables autonegotiation on port Syntax set port negotiation port-listenable disableWX1200# set port negotiation 3,5 disable WX1200# set port negotiation 2 enable Access points Following command enables PoE on ports 4See Also „ set port type ap on „ set port type wired-authon Set port poe Set port speed Changes the speed of a portSyntax set port preference port-listrj45 WX4400# set port preference 2 rj45 Set snmp profile command Set port trap Mp-352mp-372- MAP access point model WX1200# set port trap 3-4 enable „ 11a 802.11a „ 11b 802.11b „ 11g 802.11g „ poe enable disable Power over Ethernet PoE state„ radiotype 11a 11b 11g Radio type Defaults All WX ports are network ports by default WX1200# set port type ap 1-3,5 model ap3750 poe enable MAP Access Port DefaultsWX1200# set port type ap 1-3,5 model ap8250 poe enable Wired-auth Before changing the port type from ap to wired-author fromCommand Set port type Wired Authentication Port Details Vlan membership See Also „ clear port type on „ set port type ap on Port Commands Vlan Commands Deletes an entry from the forwarding database FDB Clear fdbSyntax clear fdb perm static dynamic „ display fdb on Clear vlanPort from the VLAN, make sure you specify the port number Following command completely removes Vlan marigold See Also „ set vlan port on „ display vlan config onDisplay fdb Displays entries in the forwarding database WX4400# display fdb all Describes the fields in the display fdb output See Also „ clear fdb onOutput for display fdb WX4400# display fdb Agingtime See Also „ set fdb agingtime on Display roaming Station See Also „ display roaming vlan on Describes the fields in the displayOutput for display roaming station Syntax display roaming vlan Output for display roaming vlanWX4400# display roaming vlan See Also „ display vlan config on Display tunnelOutput for display tunnel Syntax display tunnel Display vlan config Output for display vlan configSyntax display vlan config vlan-id WX1200# display vlan config burgundy Adds a permanent or static entry to the forwarding database Set fdbSyntax set fdb perm static See Also „ clear fdb on „ display fdb on Syntax set fdb agingtime vlan-idage seconds Set vlan name See Also „ display fdb agingtime onCreates a Vlan and assigns a number and name to it Syntax set vlan vlan-numname name Set vlan port Tag value to be the same but some other switches do Set vlanTunnel-affinity Adds ports 1 through 3 to the Vlan See Also „ display roaming vlan on „ display vlan config on IP Services Commands To locate commands in this chapter based on their use IP Services Commands by Usage DNS Access Enabled History Introduced in MSS Version Clear interfaceRemoves an IP interface Syntax clear interface vlan-idip See Also „ display ip alias on Clear ip aliasSyntax clear ip alias name Clear ip dns domain Removes the default DNS domain name „ ip-addr- IP address of a DNS serverSyntax clear ip dns domain WX1200# clear ip dns domain Default is an alias for IP address 0.0.0.0/0 Clear ip route„ clear ip dns domain on See Also „ display ip route on „ set ip route on Defaults The default Telnet port number is Telnet management traffic to its defaultRemoves an NTP server from a WX switch configuration Clear ip telnet Update-interval Clear ntp Clear snmp CommunitySyntax clear snmp community name comm-string „ display snmp community on Clear snmp profile Clear snmp trapReceiver Clear snmp usm See Also „ set snmp usm on „ display snmp usm on Syntax clear summertime Clear timezone Use the address Display arp Usage AllShows the ARP table Syntax display arp ip-addr „ set arp agingtime on „ set arp onOutput for display arp Shows the IP aliases configured on the wireless LAN switch Display ip aliasSee Also „ set interface on „ set interface status on Output for display interface Examples The following command displays the DNS information Display ip dns„ clear ip alias on „ set ip alias on Display ip https Shows information about the Https management portOutput for display ip dns Syntax display ip https Output for display ip https WX4400# display ip https Display ip route Shows the IP route tableSyntax display ip route destination WX4400# display ip route Output of display ip route FieldDescription Syntax display ip telnet Output for display ip telnetWX4400 display ip telnet Examples To display NTP information for a WX switch, type Display ntpShows NTP client information Output for display ntp „ set ntp server on „ set summertime on „ set timezone on Configuration Shows Snmp settings on a wireless LAN switchExamples To display Snmp settings on a WX switch, type Display snmp Output of display snmp configuration Defaults There is no summertime offset by default SummertimeSyntax display summertime WX1200# display summertime Syntax display timezone WX1200# display timedateWX4400# display timezone Defaults „ count „ set timedate on „ set timezone on Set arp „ traceroute on Following command disables ARP aging See Also „ set arp agingtime onSyntax set arp agingtime seconds WX1200# set arp agingtime Set interface Dhcp-client Syntax set interface vlan-idip dhcp-client enable disable„ clear interface on Configures the MSS Dhcp server „ enable Enables the Dhcp server„ disable Disables the Dhcp server Defaults The Dhcp server is enabled by default on a new See Also „ display dhcp-serveron Syntax set interface vlan-idstatus up down Aliases as shortcuts in CLI commands Set ip aliasSet ip dns See Also „ clear ip alias on „ display ip alias on Syntax set ip dns domain name WX1200# set ip dns domain example.com Syntax set ip dns server ip-addrprimary secondary WX switch is disabled Syntax set ip https server enable disableSyntax set ip route default ip-addr mask Set ip route Set ip route Syntax set ip snmp server enable disable WX4400# set ip snmp server enable Set ip ssh„ clear snmp notify target on Secure Shell SSH management traffic Absolute-timeout „ set ip ssh absolute-timeouton„ set ip ssh idle-timeouton „ set ip ssh server on Also disabled Idle-timeoutSet ip ssh server Maximum number of SSH sessions supported on a WX switch is Set ip telnetHistory -Introduced in MSS Version Telnet management traffic Syntax set ip telnet server enable disable Enables or disables the NTP client on a wireless LAN switch Configures a wireless LAN switch to use an NTP serverSet ntp Set ntp server RFC 1305, Network Time Protocol Version 3 Specification Defaults The default NTP update interval is 64 secondsImplementation and Analysis NTP server Set snmp User. SNMPv3 does not use community strings Set snmp community Target Set snmp notifySNMPv3 with Informs SNMPv3 with Traps Usm trap user username SNMPv2c with Informs SNMPv2c with Traps SNMPv1 with Traps Success change accepted „ notification-type- Any of the items in Table Snmp notification types Point Snmp notification types WX-1200#set snmp notify profile snmpprofrfdetect send RFDetectRogueDisappearTraps success change accepted Syntax set snmp protocol v1 v2c usm all enable disable WX-1200# set snmp security encrypted success change accepted Versions, use the set snmp community command to configure Set snmp trapSet snmp usm Community strings „ auth-type none md5 sha auth-pass-phrase string IP Services Commands Auth-type sha auth-pass-phrase myauthpword WX-1200# set snmp usm securesnmpmgr1 snmp-engine-idEncrypt-type 3des encrypt-pass-phrase mycryptpword WX1200# set summertime PDT success change accepted Following WX4400# set interface taupe ip 10.10.20.20/24 Sets the time of day and date on the wireless LAN switch Set timedateSyntax set timedate date mmm dd yyyy time hhmmss WX4400# set timedate date feb 29 2004 time 235800 Set timezone It is enabledWX1200# set timezone PST Syntax display dhcp-client Output for display dhcp-clientWX-1200# display dhcp-client See Also „ set interface dhcp-clienton Display dhcp-serverDisplays MSS Dhcp server informationSyntax display dhcp-server interface vlan-id verbose WX-1200#display dhcp-server Output for display dhcp-server Describe the fields in these displaysDisplay dhcp-server See Also „ set interface dhcp-serveron Output for display dhcp-client verbose Displays the configured Snmp community strings Outpot for display snmp communitySyntax display snmp community WX-1200#display snmp community Syntax display snmp counters Displays Snmp statistics countersWX-1200#display snmp counters Syntax display snmp notify profile WX-1200#display snmp notify profile Syntax display snmp notify target See Also „ clear snmp profile on „ set snmp profile onWX-1200#display snmp notification target Output for display snmp notification target User Name of the Snmp user EngineID Output for display Snmp status WX-1200#display snmp status Switch has booted Output for display snmp usm „ display snmp notify target on „ display snmp usm onWX-1200#display snmp usm USM users See Also „ clear snmp usm on „ display snmp usm on Opens a Telnet client session with a remote device TelnetWX4400# telnet Defaults „ dnf DisabledTraceroute See Also „ clear sessions on „ display sessions on „ no-dns- Disabled „ port „ queries „ size „ ttl„ wait Ctrl+C Error messages for traceroute „ ping on This chapter presents AAA commands alphabetically. Use to Locate commands in this chapter based on their useAAA Commands by Usage Display accounting statistics on Syntax clear accounting admin dot1x user-glob WX4400# clear accounting dot1x Nin Clear authentication Admin WX4400# clear authentication console Regina Syntax clear authentication console user-globConsoleConsole Syntax clear authentication dot1x ssid ssid-namewired Clear authentication Removes a MAC authentication rule. mac Syntax clear authentication last-resort ssid ssid-namewiredWX4400# clear authentication last-resort wired Syntax clear authentication mac ssid ssid-namewired WX4400# clear authentication mac ssid thatcorp aabbcc Access Enabled History -Introduced in MSSSyntax clear authentication proxy ssid ssid-nameuser-glob „ on Clear authentication Removes a WebAAA rule. web See Also „ set authentication proxy onWX-1200#clear authentication proxy ssid mycorp Syntax clear location policy rule-number User who is authenticated by a MAC address Clear mac-userRadius server Syntax clear mac-user mac-addr WX switch, for a user who is authenticated by a MAC address GroupACL from the profile of a user at MAC address For your Radius server Clear Mac-usergroup Mac-usergroup attr „ set mobility-profile mode on Mobility-profileClear user „ set mobility-profileon Database on the WX switch, for a user with a password Clear user attrNin „ set user on Clear user group Clear usergroupUsergroup „ clear usergroup on Syntax clear usergroup group-name attr attribute-name Displays all current AAA settings Secion added to indicate the state of the WebAAA featureDisplay aaa Time-Of-Day attribute from the group Describes the fields that can appear in display aaa output Display aaa Output Display aaa Output Stored in the local database on the WX switch Display accountingStatistics Statistics output Display accounting statistics On an WX switch Display locationPolicy „ clear location policy on Set accounting Admin consoleAre sent Server when the user roams Accesses the switch using Telnet or Web ManagerAuthenticated by Authenticated by MAC authentication Set accounting dot1x mac web Set authentication Set authentication admin Through the switch’s console Completing logonGlobs on Following methods in priority order. MSS applies multiple For more information, see Usage Syntax set authentication dot1x ssid ssid-namewired Set authentication dot1x AAA Commands Success change accepted Syntax set authentication last-resort 235 Syntax set authentication mac Set authentication mac Proxy WX-1200#set authentication proxy ssid mycorp ** srvrgrp1 Syntax set authentication web ssid ssid-namewired AAA Commands Set location policy For details, see Vlan Globs on Set location policy WX4400# set location policy deny if user eq *.theirfirm.com Set mac-user Tempvendora into Vlan kiosk1 See Also „ clear mac-useron „ display aaa on Authentication Attributes for Local Users Authentication Attributes for Local Users Filter-id outboundacl.out YY/MM/DD-HHMM Time-of-day WX4400# set mac-user 010203040506 attr filter-id acl-03.in See Also „ clear mac-user attr on „ display aaa on Syntax set mac-usergroup See Also „ clear mac-usergroup attr on „ display aaa on Syntax set mobility-profile name name port none all AAA Commands Syntax set mobility-profile mode enable disable „ set user attr on „ set usergroup on Set user Set user attr 29Jan04„ clear user on Orange That exists in the local database on the WX switch Set user group„ clear user attr on Server To add a user to a group, user the command set user group Assigns authorization attributes for the groupSet usergroup Syntax set web-aaa enable disable Examples To disable WebAAA, type the following commandSet web-aaa To locate commands in this chapter based on their use Mobility Domain Commands by Usage Mobility-domain Member Display mobility-domain config Displays the configuration of the Mobility DomainStatus See Also „ set mobility-domain member on Display mobility-domain Output WX4400# display mobility-domain status Set Command is rejectedSyntax set mobility-domain member ip-addr Mode member Seed, this command overwrites that configurationSeed-ip 192.168.1.8 Set mobility-domain mode seed domain-name Syntax set mobility-domain mode seed domain-name Mobility Domain Commands Commands Type Command Set ap dap radio auto-tune max-power on Set ap dap radio auto-tunemin-client-rateon Radio Clear ap dapSyntax clear ap port-listdap dap-num radio 1 2 all Radio-Specific Parameters WX1200# clear ap 3 radio Syntax clear radio-profile name parameter „ name Service profile name Syntax clear service-profile name See Also „ clear radio-profileon „ set radio-profile mode on WX1200# display ap config WX4400# display dap config Output for display ap config DAP „ set port type ap on „ set ap dap bias on WX1200# display ap counters Output for display ap counters Tkip Pkt Replays See Also „ display sessions network on Ccmp Pkt Replays Output for display ap dap qos-stats WX-1200#display dap qos-stats Syntax display ap dap etherstats port-listdap-num Output of display ap etherstatsWX4400# display dap etherstats „ name Name of an MAP group or Distributed MAP group Access point groupsSyntax display ap dap group name Output for display ap group „ set ap dap group onWX1200# display ap group loadbalance1 MAP WX4400# display dap status Output for display ap status WX1200# display ap status Output for display ap status Decide whether to change channel or power settings Display auto-tuneAttributes Syntax display auto-tune attributes Output for display auto-tune attributes See Also „ display auto-tune neighbors onWX1200# display auto-tune attributes ap 2 radio Neighbors 3Com radio can hearSyntax display auto-tune neighbors Ap map-numradio 1 2all Output for display auto-tune neighbors Display auto-tune Neighbors ap 2 radio Display dap Display dap global commandConnection Dap connection serial-id M9DE48B6EAD00 Output of display dap connectionSyntax display dap global dap-numserial-id serial-ID Output for display dap global WX4400# display dap global Unconfigured But that are not configured on any WX switchesLonger appears in the command’s output Network port is a member of a Vlan Output for display dap unconfigured Radio-profileDisplays radio profile information Syntax display radio-profile name ? WX4400# display radio-profile default Output for display radio-profile Tune Channel Ssid Service-profile Displays service profile information„ name Displays information about the named service profile „ ? Displays a list of service profiles Display service-profile Other WPA parameters Reset ap dap Dap auto mode enable command Usage lists the configurable template parameters and theirListed in . The commands are listed in the See Also section Configurable Template Parameters for Distributed MAPs WX1200# set dap auto success change accepted Syntax set dap auto mode enable disable Radiotype Template„ Radio type „ 11a-802.11a „ 11b-802.11b „ 11g-802.11g See Also „ set dap auto on Syntax set ap port-listdap dap-numauto bias high low See Also „ display ap dap config on Blink enable disable Syntax set dap num fingerprint hex „ ap port-list- List of MAP access ports to add to the group WX1200# set ap 4 group none success change accepted Set ap dap name Changes an MAP name „ antennatype ANT1060 ANT1120 ANT1180 internal „ antennatype ANT5060 ANT5120 ANT5180 internal Set ap dap radio auto-tune max-power Radio 1 2 auto-tune max-power power-level Set ap dap radio auto-tune max- retransmissions Radio 1 2 auto-tune max-retransmissions retransmissions Set ap dap radio auto-tune max- retransmissions Sets an MAP radio’s channel Set ap dap radio channelSyntax set ap port-listdap dap-numradio 1 Set ap dap radio auto-tune min-client-rate „ display ap dap config onRadio 1 2 auto-tune min-client-rate rate Examples Set ap 6 radio 1 min-client-rate Set ap dap radio mode Enables or disables a radio on an MAP access pointFollowing command enables radio 2 on ports 1 through Radio 1 2 mode enable disable Defaults None Set ap dap radio tx-power Sets an MAP radio’s transmit power Syntax set dap security require none optional WX-1200#set dap security require Upgrade-firmware Set ap dap Set radio-profile 11g-only Set radio-profile auto-tune channel-config Syntax set radio-profile name active-scan enable disable Set radio-profile auto-tune channel-holddown Syntax set radio-profile name auto-tune channel-holddown Set radio-profile auto-tune channel-interval Syntax set radio-profile name auto-tune channel-interval Set radio-profile auto-tune power-backoff- timer Syntax set radio-profile name auto-tune power-backoff-timer Set radio-profile auto-tune power-config WX4400# set radio-profile rp2 auto-tune power-backoff-timer Set radio-profile auto-tune power-interval Beacon-interval Clients from being able to use rogue access points „ rogue Configures radios to attack rogues onlyDefaults Countermeasures are disabled by default Following command disables countermeasures in radio profile Syntax set radio-profile name dtim-interval interval Syntax set radio-profile name frag-threshold threshold Syntax set radio-profile name long-retry threshold Syntax set radio-profile name max-rx-lifetime time Syntax set radio-profile name max-tx-lifetime time Mode Set radio-profile mode WX4400# set radio-profile rp1 mode enable Syntax set radio-profile name Syntax set radio-profile name service-profile name Syntax set radio-profile name rts-threshold threshold Defaults for Service Profile Parameters Parameter Default Value To Default Value Set radio-profile auth-psk command 349 Short-retry Wmm Syntax set service-profile Name auth-dot1x enable disable WPA IE Set service-profile auth-fallthru Syntax set service-profile name auth-psk enable disable Syntax set service-profile name beaconed enable disable Set service-profile Cipher-ccmp Cipher-tkip Use the set service-profile wep commands Cipher-wep104 Cipher-wep40 Syntax set service-profile name psk-phrase passphrase Syntax set service-profile name psk-raw hex See Also „ set service-profilecipher-ccmpon Syntax set service-profile name rsn-ie enable disable Set service-profile auth-psk command Syntax set service-profile name ssid-name ssid-name See Also „ set service-profilessid-typeon Syntax See Also „ set service-profilessid-nameon Syntax set service-profile name tkip-mc-time wait-time Ssid managed by the service profile Syntax set service-profile name web-aaa-form urlWeb-aaa-form WX4400# mkdir corpa-ssid success change accepted „ copy on „ dir on Set service-profile wep active-multicast- index„ mkdir on Set service-profile wep active-unicast- index Syntax set service-profile name wep active-unicast-index num Wep key-index Syntax set service-profile name wpa-ie enable disable Table to locate commands in this chapter based on their use STP Commands bySTP Commands by Usage STP root bridge in all VLANs on a WX switch Clear spantreePortcost Syntax clear spantree portcost port-list Portpri Portvlancost„ clear spantree portvlanpri on „ set spantree portpri on Portvlanpri „ clear spantree portcost on „ clear spantree portpri on See Also „ display spantree statistics on Spantree vlan default Syntax display spantree Output for display spantree Root Or disabled Display spantreeBackbonefast „ display spantree blockedports on „ set spantree backbonefast on BlockedportsSee Also „ display spantree on Portfast For one or more network portsSee Also „ set spantree portfast on Output for display spantree portfast Port’s VLANs „ port-list- List of portsSyntax display spantree portvlancost port-list Syntax display spantree statistics WX4400# display spantree statistics Topology change Timer value Hold timer Output for display spantree statistics Vlan Vlan ID Configpending Switch is the root or is attempting to become the root See Also „ clear spantree statistics on Syntax display spantree uplinkfast vlan vlan-id Set spantree „ set spantree uplinkfast on Examples The following command enables STP on all VLANs Configured on a WX switchFollowing command disables STP on Vlan burgundy An indirect link Fwddelay „ display spantree backbonefast on Issues a topology change message MaxageVLANs to 4 seconds „ all Changes the maximum age on all VLANs Type. lists the defaults for STP port path cost STP Port Path Cost DefaultsPath to the STP root bridge 65,535. STP selects lower-cost paths over higher-cost paths Portvlancost command See Also „ display spantree portfast on Syntax set spantree portpri port-listpriority value Bridge for a specific Vlan on a wireless LAN switch „ all Changes the cost on all VLANsType. See on To 20 in Vlan mauve Path to the STP root bridge, on one Vlan or all VLANs PortsHighest priority through 255 lowest priority „ all Changes the priority on all VLANs Priority Uplinkfast See Also „ display spantree uplinkfast on Igmp Snooping Commands Igmp Commands by Usage Display igmp Clear igmp statisticsSee Also display igmp statistics on TTL Output for display igmp TTL Syntax display igmp mrouter vlan vlan-id MrouterWX1200# display igmp Mrouter vlan orange Only one querier Defaults None Access EnabledSyntax display igmp querier vlan vlan-id WX1200# display igmp querier vlan default Output for display igmp mrouterWX1200# display igmp querier vlan orange WX1200# display igmp querier vlan red Receiver-table „ set igmp querier on Output for display igmp receiver-table See Also „ set igmp receiver onIgmp Receiver-table group 237.255.255.0/24 Shows Igmp statistics „ vlan vlan-id Vlan name or number. If you do not specify aSyntax display igmp statistics vlan vlan-id WX1200# display igmp statistics vlan orange Output of display igmp statistics From the multicast routers in the subnet Wireless LAN switch See Also „ set igmp rv on VLANs on a wireless LAN switch VLAN, the timer change applies to all VLANsSet igmp lmqi From 1 through 65,535 Syntax set igmp mrouter port port-listenable disable See Also „ display igmp statistics on Enables or disables multicast router solicitation by a WX Syntax set igmp mrsol enable disable vlan vlan-idSet igmp mrsol See Also „ set igmp mrsol mrsi on Set igmp oqi See Also „ set igmp mrsol onAll VLANs on a WX Syntax set igmp oqi seconds vlan vlan-id Set igmp Proxy-report„ set igmp lmqi on „ set igmp qri on Set igmp qi Syntax set igmp qi seconds vlan vlan-id VLANs on a WX Set igmp qriGroup. You can specify a value from 1 through 65,535 Syntax set igmp receiver port port-listenable disable Syntax set igmp querier enable disable vlan vlan-idSee Also „ display igmp querier on Set igmp rv Set igmp rv Igmp Snooping Commands Security ACL Commands Security ACL Syntax clear security acl acl-name all editbuffer-index WX4400# commit security acl acl133 configuration accepted Syntax clear security acl map acl-nameall vlan vlan-id Syntax commit security acl acl-nameall WX4400# display security acl WX4400# commit security acl allSyntax display security acl dscp Examples The following command displays the table See Also „ set security acl onWX-1200#display security acl dscp Syntax display security acl editbuffer WX4400# display security acl editbuffer Syntax display security acl hits WX4400# display security acl hits See Also „ hit-sample-rateon „ set security acl onSyntax display security acl info acl-nameall editbuffer Display security acl MapSecurity ACL is assigned Syntax display security acl map acl-name Resource-usage ACL acl111 is mappedSupport for your Product on WX4400# display security acl map acl111 WX4400# display security acl resource-usage Output of display security acl resource-usage Output of display security acl resource-usage Packets filtered by the security ACL or hits Hit-sample-rateSyntax hit-sample-rate seconds Syntax rollback security acl acl-nameall Set security acl Protocol, or IP, ICMP, TCP, or UDP packet information By TCP packets By Icmp packetsBy UDP packets „ ip „ tcp „ udp „ icmp Security ACL Commands Set security acl WX4400# set security acl ip acl123 deny 192.168.2.11 Set security acl map Security ACL Commands To locate commands in this chapter based on their use Cryptography Commands by Usage Syntax crypto ca-certificate admin eap webaaa Syntax crypto certificate admin eap webaaa See Also „ display crypto ca-certificateon Access Enabled History -Introduced in MSS Version Syntax crypto generate key admin eap ssh webaaa 512 1024 See Also display crypto key ssh on Syntax crypto generate request admin eap webaaa WX4400# crypto generate request admin Email Address admin@example.com Syntax crypto generate self-signed admin eap webaaa See Also „ crypto certificate on „ crypto generate key on WX4400# crypto generate self-signed admin Crypto otp Crypto pkcs12 „ crypto pkcs12 on See Also „ crypto otp on WX4400# crypto otp eap hap9iN#ss Display crypto Ca-certificatePkcs #7 certificate Display crypto ca-certificate Output On the WX switch Syntax display crypto certificate admin eap webaaaCertificate Describes the fields of the display See Also crypto generate key on Syntax display crypto key ssh Cryptography Commands Locate commands in this chapter based on their uses Radius Commands by Usage Clear radius See Also „ display aaa on „ set radius client system-ipon Syntax clear radius client system-ip See Also „ set radius proxy client on See Also „ set radius proxy port onSyntax clear radius proxy client all Syntax clear radius proxy port all Syntax clear radius server server-name See Also „ display aaa on „ set radius server onSyntax clear server group group-nameload-balance Set radius „ set server group on System-ip Set radius client„ clear radius server on WX4400# set radius client system-ipsuccess change accepted Port Set radius proxy„ clear radius proxy client on To 32 characters long, with no spaces or tabs Set radius server WX1200# set server group shorebirds members heron egret „ group-name- Server group name of up to 32 characters Load-balance groupSandpiper Radius and Server Group Commands On the switch Commands on802.1X Commands by Usage Performance Resets the Bonded Auth period to its default value Clear dot1xBonded-period See Also „ display dot1x on „ set dot1x bonded-periodon Port-control „ set dot1x max-reqon Quiet-period Reauth-max Reauth-period„ set dot1x reauth-maxon See Also „ display dot1x on „ set dot1x reauth-periodon „ set dot1x timeout auth-serveron „ set dot1x timeout supplicant onAuth-server Supplicant Display dot1x Tx-period„ set dot1x tx-periodon WX1200# display dot1x config WX4400# display dot1x clients Explains the counters in the display dot1x stats output Type the following command to display 802.1X statisticsWX4400# display dot1x stats Set dot1x Port-control commandAuthcontrol Authentication is enabled Examples To enable per-port 802.1X authentication on wiredAuthentication ports, type the following command Machine to start reauthentication for the user Syntax set dot1x key-tx enable disable See Also „ display dot1x on „ clear dot1x bonded-periodon See Also „ display dot1x on See Also „ clear dot1x max-reqon „ display dot1x on Authentication dot1X command See Also „ display port status on „ display dot1x on Syntax set dot1x reauth enable disable To a supplicant after a failed authenticationSyntax set dot1x quiet-period seconds See Also „ display dot1x on „ clear dot1x reauth-maxon Before the supplicant client becomes unauthorizedSyntax set dot1x reauth-max number-of-attempts Set dot1x timeout Attempts reauthenticationOut a request to a Radius authentication server See Also „ display dot1x on „ clear dot1x reauth-periodon Syntax set dot1x timeout supplicant seconds Out an authentication session with a supplicant clientSyntax set dot1x tx-period seconds Syntax set dot1X wep-rekey enable disable Wep-rekeySee Also „ display dot1x on „ clear dot1x tx-periodon Broadcast and multicast encryption keys Defaults The default is 1800 seconds 30 minutes Wep-rekey-period„ seconds Specify a value between 30 and 1,641,600 19 days To 300 seconds Clear sessions Telnet sessions Network VLANs, or session ID WX4400# clear sessions network mac-addr To clear session 9, type the following commandWX1200# clear sessions network session-id Display sessions WX4400 display sessions console WX4400 display sessions adminWX4400 display sessions telnet See Also „ clear sessions on Display sessions telnet client Output Syntax display sessions network „ Summary display See on „ Verbose display See on „ display sessions network session-id display See onWX1200# display sessions network WX1200# display sessions network mac-addr 00055d7e981a WX1200# display sessions network verbose WX1200# display sessions network session-id Display sessions network summary Output Additional display sessions network verbose Output Time 802.1X protocol on a wired authentication port Display sessions network session-id Output See Also „ clear sessions network on Session Management Commands To locate the commands in this chapter based on their use RF Detection Commands by Usage Examples The following command clears MAC address Clear rfdetectAttack-list Removes a MAC address from the attack list Countermeasures Mac Clear rfdetect Black-listIgnore Ssid-list „ display rfdetect ignore on„ set rfdetect ignore on „ set rfdetect ssid-liston Vendor-list Display rfdetect„ set rfdetect vendor-liston „ display rfdetect vendor-liston RF Detection Commands Countermeasures Mobility DomainDomain Display rfdetect countermeasures Output Data Displays information about the APs detected by a WX switchSyntax display rfdetect data Display rfdetect data Output WX1200# display rfdetect data Syntax display rfdetect ignore Ignore listWX4400# display rfdetect ignore Total number of entries Bssid mac-addr Displays rogues that are using the specified During RF detection scansSyntax display rfdetect mobility-domain WS1200# display rfdetect mobility-domain Ssid 3Com-webaaa WS1200# display rfdetect mobility-domain ssid 3Com-webaaa Display rfdetect mobility-domain Output Following command displays detailed information for a BssidWX1200# display rfdetect mobility-domain bssid 000b0e0004d1 Display rfdetect mobility-domain ssid or bssid Output WX switch „ display rfdetect data onDisplays the entries in the permitted Ssid list „ clear rfdetect ssid-liston Display ap dap status command Visible Display rfdetect visible Output WX1200# display rfdetect visible Radio Active-scan Set rfdetectAddresses of APs and clients Configured. WX switches do not share attack lists Examples The following command adds MAC addressDefaults The client black list is empty by default Configured. WX switches do not share client black lists Set rf detect Countermeasures Mac Set rfdetect ignore See Also „ display log buffer on WX switches in a Mobility Domain Signature Examples The following command adds Ssid mycorp to the list Only for the SSIDs that are on the listPermitted SSIDs Device’s OUI is in the permitted vendor list Syntax display rfdetect attack-list Trailing 000000 value is requiredWX1200# display rfdetect attack-list Displays the wireless clients detected by an WX switch ClientsSyntax display rfdetect black-list WX1200# display rfdetect black-list Display rfdetect clients Output WX1200# display rfdetect Clients Display rfdetect clients mac Output From the wired side of the network addressed to File Management Commands Dir command output Locally on the switchTape archive tar format „ tftp/ip-addr/filename- Name of the archive file to create Syntax clear boot config „ reset system on CopyPerforms the following copy operations „ Copies a file from a Tftp server to nonvolatile storage WX4400# copy test-config new-config WX4400# copy floorwx tftp//10.1.1.1/floorwx File or the running configuration DeleteImmediately deletes the specified file Syntax delete url Dir „ copy on „ delete on Describes the fields in the dir outputOutput for dir Display boot Reboot and configured for use after the next rebootAccess Access Describes the fields in the display boot output Displays the configuration running on the WX switch Display configSyntax display config area area all See Also „ load config on „ save config on And, optionally, for any attached MAP access pointsWX4400# display config area vlan Display version WX1200# display version WX1200# display version details Load config Running configuration with the commands in the loaded fileDescribes the fields in the display version output Output for display version Following command loads configuration file testconfig1 Syntax load config urlWX4400# load config WX4400# load config testconfig1 Mkdir Creates a new subdirectory in nonvolatile storage Restarts an WX switch and reboots the software Reset system„ dir on „ rmdir on Restore Generate new key pairs and certificates on the switch „ backup on WX1200# restore system tftp/10.10.20.9/sysabakRmdir Removes a subdirectory from nonvolatile storage Save config Saves the running configuration to a configuration fileSyntax save config filename „ dir on „ mkdir on Set boot Configuration-fileConfiguration Testconfig1 Syntax set boot partition boot0 boot1 File Management Commands Trace Commands Deletes running trace commands and ends trace processes Clear log traceClear trace Deletes the log messages stored in the trace buffer WX switch, or all possible trace options Display traceSyntax display trace all WX4400# display trace Save trace AuthenticationSet trace Authorization See Also „ clear trace on „ display trace on Set trace dot1x Set trace sm Syntax set trace sm mac-addr mac-address port port-num Trace Commands Snoop Commands Clear snoop map Clear snoop„ display snoop info on Set snoop „ set snoop map on„ display snoop on „ display snoop map on Chapter Snoop Commands WX1200# set snoop snoop1 observer 10.10.30.2 snap-length Set snoop map FilterRadio 1 of the MAP Radio 2 of the MAP. This option does not apply to Set snoop mode To an MAP radio and enable the filterEnable stop-afternum-pkts- Enables the snoop filter All snoop filters Display snoop map command For all snoop filters configured on a WX switchDisplay snoop Displays the MAP radio mapping for all snoop filters Display snoop info Shows the configured snoop filters See Also „ clear snoop onSyntax display snoop filter-name WX1200# display snoop info snoop1 Snoop map snoop1 Examples display snoop stats filter-namedap-numradio Display snoop stats Output Snoop1Snoop stats snoop1 Chapter Snoop Commands Clear log Syntax clear log buffer server ip-addr See Also „ clear log trace on Log buffer facility ? You can view event messages archived in the bufferWX4400# display log buffer facility AAA „ display log config on Log config„ clear log on „ set log on „ clear log on Syntax display log trace +-/number-of-messages Set log Storage„ console Sets log parameters for console sessions Address in dotted decimal notation „ trace Sets log parameters for trace files See Also Set log trace See Also „ display log config onMbytes System LOG Commands Boot Prompt Commands Boot Prompt Autoboot Boot „ BT=type Boot type„ DEV=device Location of the system image file „ FN=filename System image filename „ change on „ display on Change Syntax change Create Syntax create Usage When you type the delete command, the next-lower Examples To remove the currently active boot profile, typeProfiles, see display on Syntax delete Diag Syntax diag Syntax display Defaults None Output of display command „ change on „ create on „ delete on „ next on Fver For an individual command „ command-name- Boot prompt commandDisplays a list of the boot prompt commands „ ls on Next Syntax next Reset Resets a WX switch’s hardwareSyntax reset Command at the boot prompt „ on Enables the poweron test flag „ OFF Disables the poweron test flagDefaults The poweron test flag is disabled by default Test Dir or fver command Type the following command at the boot promptVersion Syntax version Services Register YourProduct Purchase Access Software TroubleshootOnline Downloads Contact Us Country Telephone Number Latsupportanc@3com.com Index Delete 544, 597 diag Dir 545, 598 disable 33 display Index Index Index Traceroute Version