Multicast-domain switch-group-pool, 1511

1511

Parameters switch-delay: MDT switching delay in seconds, namely the delay time for multicast traffic to be switched from the share-MDT to the switch-MDT, in the range of 3 to 60.

Description Use the multicast-domainswitch-delaycommand to configure the MDT switching delay.

Use the undo multicast-domain switch-delay command to restore the system default.

By default, the MDT switching delay time is 5 seconds.

Examples # Set the MDT switching delay to 20 seconds in VPN instance mvpn.

<Sysname> system-view

[Sysname] ip vpn-instance mvpn

[Sysname-vpn-instance-mvpn] multicast-domain switch-delay 20

multicast-domain switch-group-pool

Syntax multicast-domainswitch-group-poolswitch-group-pool { mask mask-length } [ threshold threshold-value acl acl-number ] *

undo multicast-domain switch-group-pool

View VPN instance view

Parameters switch-group-pool: The start address of the switch-group-pool, in the range of 224.0.1.0 to 239.255.255.255.

mask: Mask for addresses in the switch-group-pool, in the range of 255.255.255.0 to 255.255.255.255, meaning the switch-group-pool contains 1 to 256 group addresses.

mask-length: Mask length for addresses in the switch-group-pool, in the range of 24 to 32, meaning the switch-group-pool contains 1 to 256 group addresses.

threshold-value: Traffic rate threshold that will trigger MDT switching, in units of kbps. The effective range is 0 to 4194304.

acl-number: Advanced ACL number, in the range of 3000 to 3999. An advanced ACL is used to define the (S, G) entry or entries to which the configured MDT switching condition will apply. If you do not specify an ACL, the configured MDT switching condition will apply to all (S, G) entries.

Description Use the multicast-domain switch-group-pool command to configure the address range of the switch-group-pool and the switching condition.

Use the undo multicast-domain switch-group-pool command to restore the system default.

Page 1511

Image 1511

3Com MSR 50, MSR 30 manual Multicast-domain switch-group-pool, Undo multicast-domain switch-group-pool, 1511

Contents

H3C MSR 20/30/50 Series Routers United States Government Legend 3Com Corporation Campus Drive Marlborough, MA USA Contents General Ethernet Interface Configuration Commands Adsl Interface Configuration CommandsPOS Interface Configuration Commands Fundamental CE1/PRI Interface Configuration Commands Fundamental Serial Interface Configuration Commands 14 E1-F Interface Configuration Commands Fundamental CT1/PRI Interface Configuration Commands Fundamental CT3 Interface Configuration Commands 15 T1-F Interface Configuration CommandsFundamental CE3 Interface Configuration Commands DCC Configuration Commands Isdn BRI Interface Configuration CommandsATM Configuration Commands 340 Basic Dlsw Configuration Commands Frame Relay Configuration Commands Lapb and X.25 Configuration Commands Garp Configuration CommandsGvrp Configuration Commands Hdlc Configuration Commands 455 425 Display x25 hunt-group-info Display x25 map 426451 X25 pvc X25 queue-length 453 X25 receive-threshold 454 Port Mirroring Configuration Commands Link Aggregation Configuration CommandsLink Aggregation Debugging Commands Modem Configuration Commands Pppoe Client Configuration Commands PPP Link Efficiency Mechanism Configuration CommandsPppoe Server Configuration Commands Debugging ppp PPP Debugging CommandsBridging Configuration Commands Isdn Configuration Commands Mstp Configuration Commands Port Isolation Configuration Commands Vlan Configuration CommandsPORT-BASEDVLAN Configuration Commands Voice Vlan Configuration Commands ARP Configuration Commands Cpos Interface Configuration Commands Proxy ARP Configuration Commands Gratuitous ARP Configuration CommandsARP Source Suppression Configuration Commands Authorized ARP Configuration Commands Bootp Client Configuration Commands Dhcp Relay Agent Configuration CommandsDhcp Client Configuration Commands Dhcp Snooping Configuration Commands IP Performance Configuration Commands DNS Configuration CommandsIP Accounting Configuration Commands IP Addressing Configuration Commands Fast Forwarding Commands IP Unicast Policy Routing Configuration CommandsUDP Helper Configuration Commands Urpf Configuration Commands Display natpt aging-time 864 display natpt all NAT-PT Configuration Commands840 Display tcp ipv6 status 842 Display natpt address-group 863 69 IPV6 Unicast Policy Routing Configuration Commands Dual Stack Configuration CommandsTunneling Configuration Commands IP Routing Table Commands Terminal Access Configuration Commands BGP Configuration Commands 983 Peer advertise-communityBGP/BGP-VPN instance view Ebgp-interface-sensitive977 981 Log-peer-change IS-IS Configuration Commands BGP Debugging Commands Ospf Configuration Commands IS-IS Debugging Commands 1140 1155 Snmp-agent trap enable ospf1117 1128 1179 RIP Configuration CommandsRouting Policy Common Configuration Commands 82 IPV6 BGP Configuration Commands 79 IPV4 Routing Policy Configuration Commands80 IPV6 Routing Policy Configuration Commands Static Routing Configuration Commands 1246 12231243 84 IPV6 OSPFV3 Configuration Commands 83 IPV6 IS-IS Configuration Commands Delete ipv6 static-routes all 1325 ipv6 route-static 85 IPV6 Ripng Configuration Commands86 IPV6 Static Routing Configuration Commands Multicast Routing and Forwarding Configuration Commands 1366 Igmp Configuration CommandsMsdp Configuration Commands Cache-sa-enable 1365 display msdp brief 1376 PIM Configuration Commands 1429 14211422 1451 MLD Configuration Commands93 IPV6 PIM Configuration Commands 1505 Multicast VPN Configuration Commands1495 Display multicast-domain vpn-instance share-group Mpls Basics Configuration Commands Mpls TE Configuration Commands Mpls rsvp-te reliability 1610 Mpls rsvp-te resvconfirm 1611 Mpls L3VPN Configuration Commands Mpls L2VPN Configuration Commands 1697 VAM Server Configuration Commands GRE Configuration Commands VAM Client Configuration CommandsIpsec Profile Configuration Commands Dvpn Tunnel Configuration Commands Defining Class Commands Traffic Policing TP Configuration CommandsTraffic Shaping Configuration Commands Line Rate Configuration Commands WFQ Configuration Commands Fifo Queuing Configuration CommandsPQ Configuration Commands CQ Configuration Commands Port Priority Trust Mode Configuration Commands QOS Token Configuration CommandsPriority Mapping Table Configuration Commands Port Priority Configuration Commands Reset dar session FR QOS Configuration Commands126 802.1X Configuration Commands AAA Configuration Commands access-limit 1958 Radius Configuration Commands1927 Packet Filter Firewall Configuration Commands Hwtacacs Configuration Commands NAT Configuration Commands Aspf Configuration Commands aging-timeMAC Authentication Configuration Commands PKI Configuration Commands 138 IPV4 ACL Configuration Commands Portal Configuration CommandsRSH Configuration Commands rsh Common Configuration Commands Ipsec Configuration Commands 142 SSH2.0 Configuration Commands IKE Configuration Commands SSL Configuration Commands Sftp Configuration Commands bye Device Management Commands Backup Center Configuration Commands146 IPV4-BASEDVRRP Configuration Commands Vrrp Configuration Commands for IPV6 2276 NQA Client Configuration CommandsTemperature-alarm enable 2263 Temperature-limit 2262 Rmon Configuration Commands NQA Server Configuration CommandsNetstream Configuration Commands NTP Configuration Commands File System Configuration Commands cd Snmp Configuration Commands Tftp Client Configuration Commands Configuration File Management CommandsFTP Server Configuration Commands FTP Client Configuration Commands ascii Information Center Configuration Commands System Maintaining CommandsSystem Debugging Commands Basic Configuration Commands 2460 User Interface Configuration Commands OAP Module Configuration Commands MAC Address Table Management Configuration CommandsPOE Configuration Commands Track Configuration Commands Acfp Configuration CommandsAcsei Server Configuration Commands Acsei Client Configuration Commands Area 2554 area-id Voip Configuration Commands address2551 Reset ipx routing-table statistics protocol 2546 2592 2639 Dial Plan Configuration Commands175 E1 and T1 Configuration Commands ani Caller-permit SIP Configuration Commands FAX Over IP Configuration Commands177 H.323 Configuration Commands 2734 Vofr Configuration CommandsVoice Radius Configuration Commands aaa-client 2716 Text Conventions About this GuideLists icon conventions that are used throughout this guide Lists text conventions that are used throughout this guide Documentation Related Area Ospf view 1108 area OSPFv3 view Alphabetical Listing of CommandsPage Page Rp IPv6 PIM view 1464 c-rp PIM view Page Display bgp vpnv4 vpn-instancerouting-table Page Display ipv6 policy-based-route statistics Page Page Page Page Page Fr compression frf9 385 fr compression iphc Page Igmp last-member-query-interval Ipv6 nd autoconfig managed-address-flag Page Page Page Mpls te resv-style 1631 mpls te retry 2308 Peer allow-as-loopBGP/BGP-VPN instance view Peer ebgp-max-hopBGP/BGP-VPN instance viewPeer keep-all-routesBGP/BGP-VPN instance view Peer public-as-onlyBGP/BGP-VPN instance view Peer next-hop-localBGP/BGP-VPN instance viewPeer preferred-valueBGP/BGP-VPN instance view Peer next-hop-invariableBGP-VPNv4 subaddress family view Pppoe-servermax-sessionsremote-mac Qos wred ip-precedence 1850 qos wred queue table Primary accounting Hwtacacs scheme view Reset aspf session 2007 reset atm interface 112 reset bgp Reset pim ipv6 control-message counters Page Page Statistics interval 1562 step for IPv4 2100 step for IPv6 Ssl client-policy 2215 ssl server-policyPage Page Page X29 timer inviteclear-time Page Syntax display interface atm interface-number Public ATM and DSL Interface CommandsDisplay interface atm Interface atm Reset atm interfaceSyntax reset atm interface atm interface-number Clock Configuration CommandsCable Undo code CodeCode ami hdb3 Code ami b8zs 115 Differential-delayDisplay interface ima-group Syntax display interface ima-group group-interfacenumber ESF ADM Frame-formatView ATM E1/T1 interface view Parameter ATM direct mapping CRC4 ADM Syntax ima ima-group group-number Undo ima ima-group Frame-lengthIma ima-group Syntax frame-length 32 64 128 Undo frame-length Syntax ima-clock ctc link-number number itc Undo ima-clock Ima-clockExample # Add the link of ATM E1 interface 5/0 to IMA group Undo ima-test Ima-standardIma-test Ima-test link-number number pattern-id id Syntax loopback cell local payload remote Undo loopback By default, IMA group interface test is disabledInterface ima-group Loopback Syntax scramble Undo scramble Min-active-linksScramble Syntax min-active-links number Undo min-active-links Parameter None View ATM E3/T3 interface view Slave Sets the clock mode as slaveSyntax cable long short Undo cable Frame-format cbit-adm cbit-plcp m23-adm m23-plcp Frame-format g751-adm g751-plcp g832-adm Loopback cell local payload remote ATM E3/T3 Interface Configuration Commands Frame-format sdh sonet Loopback cell local remote 129 View ATM OC-3c interface view, STM-1 interface view ATM OC-3C/STM-1 Interface Configuration Commands View ATM G.SHDSL interface view Shdsl Interface Configuration CommandsActivate Syntax activate Undo activate Field Description Display dsl configuration 133 Display dsl statusSyntax display dsl status interface atm interface-number Gspn 135 Description on the fields of the display dsl status command ITU G991.2 Annex A, ITU Display dsl versionSyntax display dsl version interface atm interface-number Shdsl annex Shdsl mode Syntax shdsl psd asymmetry symmetry Undo shdsl psd Example # Set the operating mode of interface ATM 5/0 to COShdsl psd Shdsl rate Use the undo shdsl snr-margincommand to restore the default Single-pair interface rate to auto modeKbps four-wire G.SHDSL interface rate is 4,624 kbps # Configure ATM 5/0 to operate in the auto-negotiation mode Undo shdsl wire Shdsl wireShdsl wire 2 4-auto-enhanced 4-enhanced 4-standard 141 Shdsl Interface Configuration Commands Example # Activate Adsl interface 2/0 Adsl Interface Configuration CommandsView ATM Adsl interface view Undo adsl standard Adsl standardAdsl tx-attenuation Adsl standard auto g9923 g9925 gdmt glite t1413 145 Bootrom update file Display dsl configuration LS0US 147 Dslam FieldDescription Bdcm 149 Adsl Interface Configuration Commands Syntax crc 16 Undo crc POS Interface Configuration CommandsCrc Syntax display interface pos interface-number Display interface pos LCP opened, Ipcp opened, IP6CP opened 153 Syntax display ipv6 interface pos interface-number Display ip interface posDisplay ipv6 interface pos Display ip interface pos interface-number Flag # Set the framing format on interface POS 1/0 to SDH Related command display interface posExample # Set the SDH overhead byte J0 of POS1/0 interface Remote External loopback Link-protocolLoopback local remote Local Internal loopback Syntax mtu size MtuThat the state of the link layer protocol is reported up Interfaces cannot be connected successfully 159 Example # Enable payload scrambling on interface POS 1/0Threshold Syntax threshold sd sf value Undo threshold sd sf Example # Set the SD threshold to 10e-4 for POS 1/0 Description General Ethernet Interface Configuration CommandsCombo enable Related command display port combo and shutdown Character Meaning Display brief interfaceSpecial characters used in regular expressions 163 Related command interfaceExample # Display brief information of interfaces Interface name Acronyms Display interfaceAcronyms for different types of Interface Pvid Field 165 Output queue Fifo queuing 167 Syntax duplex auto full half Undo duplex Related command speedDuplex Flow-control Syntax loopback external internal Undo loopback InterfaceCan be represented as 1/0 E1/0 Undo port link-mode Support for these two commands varies with device modelsPort link-mode Port link-mode bridge route 171 Reset counters interfaceExample # Configure Ethernet1/0 to work in bridge mode View User view Speed Shutdown 173 Related command duplex General Ethernet Interface Configuration Commands Broadcast-suppression Display port hybrid trunk Display loopback-detectionDisplay port Syntax display loopback-detection Examples Display port-group manualDisplay port-group manual all name port-group-name Undo group-member interface-list Flow-intervalGroup-member Syntax flow-interval interval Undo flow-interval 179 Loopback-detection control enable View System view/Ethernet interface view Loopback-detection enableRelated command loopback-detection control enable Loopback-detection interval-time 181 Loopback-detection per-vlan enableRelated command display loopback-detection Mdi across auto normal Optical port of a Combo port does not support this commandMdi Multicast-suppression Undo port-group manual port-group-name Port-groupPort-group manual port-group-name aggregation agg-id Syntax virtual-cable-test Currently, these two commands are not supportedUnicast-suppression Virtual-cable-test 185 Page Syntax timer hold seconds Undo timer hold Timer holdExample # Configure MTU for Ethernet1/0 to be 1,000 bytes Configuration Commands for Ethernet Interfaces in Route Mode Baudrate Fundamental Serial Interface Configuration CommandsAsync mode Syntax async mode flow protocol Undo async mode View Serial interface view Clock serial interface viewUndo baudrate Clock dteclk1 dteclk2 dteclk3 dteclk4 dteclkauto Clock selection option Description Dteclk1191 View Synchronous serial interface view Code nrziCountry-code Syntax code nrzi Undo code Asynchronous serial interface detect dsr-dtr Example # Configure to adopt 32-bit CRCDetect Syntax crc 16 32 none Undo crc View Asynchronous serial interface view Eliminate-pulseSyntax eliminate-pulse Undo eliminate-pulse Syntax invert receive-clock Undo invert receive-clock Idle-markInvert receive-clock Syntax idle-mark Undo idle-mark Syntax invert transmit-clock Undo invert transmit-clock Invert transmit-clock 197 Mtu on serial interfacesSyntax loopback Undo loopback Syntax phy-mru size Undo phy-mru Physical-modePhy-mru Syntax physical-mode async sync 199 Reverse-rtsSyntax reverse-rts Undo reverse-rts Baudrate VirtualbaudrateVirtualbaudrate virtualbaudrate Undo virtualbaudrate Channel-set CE1/PRI interface view Fundamental CE1/PRI Interface Configuration Commands Clock Clock CE1/PRI interface view Controller e1 number Code CEI/PRI interface viewController e1 Syntax detect-ais Undo detect-ais Detect-aisCrc 16 32 none 205 Description on the fields of the commandDisplay controller e1 Syntax display controller e1 interface-number Undo error-diffusion restraint config Error-diffusion restraint config Example # Enable error packets diffusion restraint Error-diffusion restraint enableError-diffusion restraint restart-channel By default, error packets diffusion restraint is enabled Two types of line idle code are available 0x7E and 0xFF Frame-format CE1/PRI interface viewIdlecode CE1/PRI interface view Undo itf type number Itf CE1/PRI interface viewItf number number type 7e ff Pri-set timeslot-list list Loopback CE1/PRI interface viewPri-set CE1/PRI interface view Loopback local payload remote Display controller e1 interface-number command Reset counters controller e1Reset counters controller e1 interface-number Command Undo using Using CE1/PRI interface viewUsing ce1 e1 Level-2 , level-3 , and level-4 Fundamental CT1/PRI Interface Configuration CommandsAlarm-threshold Level-2 Ranges from 1 to 1,440 Bert CT1/PRI interface viewBert pattern 215 220 time minutes unframed Undo bert 655ft Cable CT1/PRI interface viewChannel-set CT1/PRI interface view View CT1/PRI interface view Clock CT1/PRI interface view # Set the line code format of the interface T1 2/0 to AMI Code CT1/PRI interface viewController t1 Ami Adopts AMI line code format Undo data-coding Data-coding CT1/PRI interface viewData-coding inverted normal 219 Display controller t1Syntax display controller t1 interface-number Clock or slave for the line clock 221 Error-diffusion restraint config 223 By default, the function is disabledExample # Enable error packet diffusion restraint Set-number argument is a channel set number Support of this command varies with device modelError packet diffusion restraint function Fdl Frame-format esf sf Frame-format CT1/PRI interface viewIdlecode CT1/PRI interface view Syntax loopback local payload remote Itf CT1/PRI interface viewLoopback CT1/PRI interface view Syntax itf number number type 7e ff Undo itf number type Loopback on the CT1/PRI interface Remote Enables the interface to perform remote loopback# Enabled remote loopback on interface T1 2/0 Pri-set CT1/PRI interface view # Clear the controller counter for CT1/PRI interface T1 2/0 Reset counters controller t1Reset counters controller t1 interface-number For a CT1/PRI interface 229 Sendloopcode Fundamental CT1/PRI Interface Configuration Commands Display fe1 serial interface-number E1-F Interface Configuration CommandsDisplay fe1 Undo fe1 cable Fe1 cableFe1 clock Fe1 cable long short Fe1 detect-ais Fe1 code Fe1 loopback Fe1 frame-format Syntax fe1 timeslot-list list Undo fe1 timeslot-list Local Sets the interface in internal loopback modeFe1 timeslot-list Undo fe1 loopback Syntax fe1 idlecode 7e ff Undo fe1 idlecode Related command fe1 unframedFe1 idlecode Fe1 itf Undo fe1 unframed Fe1 unframedFe1 unframed Related command fe1 timeslot-list Display ft1 serial interface-number T1-F Interface Configuration CommandsDisplay ft1 Description on the fields of the display ft1 serial command Bert statestopped, not completed 241 T1-F interface view Ft1 bert T1-F interface viewFt1 bert pattern 215 220 time minutes unframed Undo ft1 bert 243 Ft1 cableSyntax ft1 cable long decibel short length Undo ft1 cable View T1-F interface view Undo ft1 clock Ft1 clockFt1 code Ft1 clock master slave Undo ft1 data-coding Ft1 data-codingFt1 data-coding inverted normal Ft1 frame-format Ft1 fdl Undo ft1 idlecode Ft1 idlecodeFt1 itf Ft1 idlecode 7e ff Undo ft1 loopback Use the undo ft1 loopback command to restore the defaultFt1 loopback Ft1 loopback local payload remote 249 # Set T1-F interface Serial 2/0 in local loopback modeFt1 timeslot-list On the T1-F interface Ft1 alarm-thresholdUndo ft1 alarm-threshold 251 Ft1 sendloopcode T1-F Interface Configuration Commands Bert pattern 27 211 215 qrss time number unframed Fundamental CE3 Interface Configuration CommandsBert CE3 Interface Example # Enter the view of interface E3 2/0 Clock CE3 interface viewController e3 Display controller e3 255 Display controller e3Syntax display controller e3 interface-number Fundamental CE3 Interface Configuration Commands 257 E1 bert Syntax e1 line-numberset clock master slave Related command e1 unframedE1 channel-set E1 set clock 259 E1 set frame-formatUndo e1 line-numberset clock View CE3 interface view Undo e1 line-numbershutdown E1 set loopbackE1 shutdown Undo e1 line-numberunframed Related command e1 channel-setE1 unframed Fe3 These two commands are only available in E3 mode CE3 interface in FE3 mode viewSet the DSU mode or the subrate Use the undo fe3 command to restore the default Undo national-bit Loopback CE3 interface viewNational-bit National-bit 0 Example # Set the national bit to 0 on interface E3 2/0 Using CE3 interface viewRelated command controller e3 Syntax using ce3 e3 Undo using Undo alarm detect generate ais febe idle rai Fundamental CT3 Interface Configuration CommandsAlarm CT3 interface view Alarm detect generate ais febe idle rai Bert CT3 interface view # Enable CT3 interface T3 2/0 to send AIS alarm signals 267 Cable CT3 interface viewClock CT3 interface view Syntax cable feet None Adopts no CRC Related command display controller t3Controller t3 Example # Enter the view of interface T3 2/0 269 Display controller t3Syntax display controller t3 interface-number AIS 271 Configurable and default to line LOS, LOF, AIS, or RAI Feac CT3 interface view Frame-format c-bit m23 Frame-format CT3 interface viewFt3 275 Mdl CT3 interface view Loopback CT3 interface view 277 # Send path messages on CT3 interface T3 2/0 T1 alarm# Set LIC to hello for CT3 interface T3 2/0 279 T1 bert T1 channel-set Related command t1 unframed 281 T1 sendloopcode T1 set frame-format T1 set clock 283 T1 set loopbackT1 set fdl View CT3 interface view T1 show 285 Description on the fields of the t1 show commandT1 shutdown Syntax t1 line-numberunframed undo t1 line-numberunframed Related command t1 channel-setT1 unframed Undo t1 line-numbershutdown T3 Sets the CT3 interface to operate in unchannelized mode Using CT3 interface viewUsing ct3 t3 Ct3 Sets the CT3 interface to operate in channelized mode Fundamental CT3 Interface Configuration Commands Fixed Isdn interfaces on your router, if there is any Isdn BRI Interface Configuration CommandsLoopback Isdn BRI interface view Loopback b1 b2 both Isdn BRI Interface Configuration Commands Atm-class ATM Configuration CommandsRelated command atm-class Atm class View ATM P2P sub-interface view Related command atm classAtm-link check Syntax atm-link check Undo atm-link check Display atm class atm-class-name Related command Display atm interface ExampleDisplay atm class Syntax display atm interface atm interface-number Display atm interface 295 Display atm map-info State Display atm pvc-groupVPI/VCI PVC-NAME 297 Display atm pvc-info Index EncapsulationSyntax encapsulation aal5-encap Undo encapsulation 299 Ip-precedenceExample # Enter Atm1/0 interface View PVC view/ATM Class view Related command pvc-group,pvcMap bridge Map ip inarp minutes broadcast Undo map ip inarp # Configure an IP address 10.1.1.1/16 for the VE interfaceMap ip # Create PVC 1/102 on the ATM interface Atm2/0 Syntax map ppp virtual-template vt-number Undo map ppp Map ppp 303 # Create a PPPoA map using the VT interface created# Create PVC 1/101 on interface Atm1/0 Oam ais-rdi 305 Oam frequencyUndo oam frequency Pvc Oamping interface Interface type Related command display atm pvc-info,pvc max-numberVCI range for each type of ATM interface 307 Syntax pvc max-number max-number Undo pvc max-number Related command ip-precedence,pvcPvc-group Pvc max-number Undo pvp limit vpi Pvp limit Interface type Value range of output-pcr Service cbrExample # Set the traffic of VP with vpi 1 to 2M Syntax service ubr output-pcr Service ubrService vbr-nrt Related command service vbr-nrt,service vbr-rt,service ubr Related command service ubr, service vbr-rt, and service cbr Service vbr-rt 313 Parameters None# Bring up ATM 5/0 Syntax transmit-priority value Undo transmit-priority Transmit-priority Dialer bundle-member DCC Configuration CommandsRelated command dialer bundle-member Dialer bundle Dialer callback-center Related command dialer bundle 317 Dialer call-in Dialer circular-group Related command dialer callback-centerRelated command interface dialer Bundle-member command Dialer enable-circularDialer enable-circular Undo dialer enable-circular Dialer isdn-leased physical interface view Related command dialer circular-groupRelated command dialer threshold Dialer flow-interval 321 Dialer numberSyntax dialer number dial-number Undo dialer number Syntax dialer priority priority Undo dialer priority Related command dialer routeDialer priority Dialer queue-length 323 Dialer route Dialer threshold 325 Dialer timer autodialRelated command dialer flow-interval Dialer timer compete Syntax dialer timer idle seconds Undo dialer timer idle Dialer timer enableDialer timer idle Syntax dialer timer enable seconds Undo dialer timer enable Syntax dialer user username Undo dialer user Dialer timer wait-carrierDialer user 329 Dialer-groupExample # Add a remote username routerb Syntax dialer-group group-number Undo dialer-group Undo dialer-rule group-number Related command dialer-ruleExample # Add interface Serial 2/0 to dialer access group Dialer-rule Number Related command dialer-groupDisplay dialer Any view Information about all the dialer interfaces Display interface dialerDisplay interface dialer number Number Dialer interface number 333 Interface dialerSyntax interface dialer number Undo interface dialer number Undo ppp callback client server Ppp callbackPpp callback ntstring Ppp callback client server 335 Related command ppp callbackUndo ppp callback ntstring DCC Configuration Commands Syntax display dlsw circuits circuit-id verbose Basic Dlsw Configuration CommandsExample # Configure Serial 1/0 to use Nrzi encoding Display dlsw circuits Display dlsw information local ip-address Display dlsw information 339 Display dlsw remote# Display the local information about capabilities exchange Syntax display dlsw remote ip-address # Display the reachability information of DLSw Display dlsw reachable-cacheDisplay dlsw reachable-cache Information of DLSw 341 Description on the fields of the display llc2 commandDisplay llc2 Syntax display llc2 circuit circuit-id Dlsw bridge-set Dlsw enableSyntax dlsw enable Undo dlsw enable 343 # Enable DLSwDlsw ethernet-frame-filter Dlsw local 345 # Allow the router to access SAP addresses 12Dlsw reachable Undo dlsw remote ip-address # Permit access to user-configured MAC addresses onlyDlsw reachable-cache Dlsw remote 347 Syntax dlsw reverse mac-address Related command sdlc mac-map remoteDlsw reverse Dlsw max-transmission 349 Dlsw multicastUndo dlsw multicast Dlsw timer 351 Link-protocol sdlcSyntax link-protocol sdlc Syntax llc2 max-pdu length Undo llc2 max-pdu Llc2 max-ackLlc2 max-pdu Syntax llc2 max-ack length Undo llc2 max-ack 353 Llc2 max-send-queueLlc2 max-transmission Syntax llc2 max-send-queue length Undo llc2 max-send-queue Undo llc2 modulo Llc2 moduloLlc2 receive-window Llc2 modulo 8 355 Llc2 timer ackLlc2 timer ack-delay Syntax llc2 timer ack mseconds Undo llc2 timer ack Syntax llc2 timer detect mseconds Undo llc2 timer detect Llc2 timer busyLlc2 timer detect Syntax llc2 timer busy mseconds Undo llc2 timer busy 357 Llc2 timer pollSyntax llc2 timer poll mseconds Undo llc2 timer poll Reset dlsw reachable-cache Llc2 timer rejectReset dlsw circuits 359 Reset dlsw tcpSyntax reset dlsw tcp ip-address Description on the fields of the reset dlsw tcp command Sdlc controller 361 Sdlc enable dlswSyntax sdlc enable dlsw Undo sdlc enable dlsw Sdlc mac-map local Sdlc mac-map remote Syntax sdlc max-send-queue length Undo sdlc max-send-queue Sdlc max-pduSdlc max-send-queue Syntax sdlc max-pdu number Undo sdlc max-pdu Specifies the modulus value to be Sdlc max-transmissionSdlc modulo View Synchronous serial interface view 365 Related command sdlc sap-map remoteSdlc sap-map local Syntax sdlc simultaneous Undo sdlc simultaneous Related command sdlc sap-map localSdlc sap-map remote Sdlc simultaneous Undo sdlc status primary secondary Sdlc statusSdlc status primary secondary Syntax sdlc timer ack mseconds Undo sdlc timer ack Sdlc timer ackSdlc timer lifetime Syntax sdlc window length Undo sdlc window Sdlc timer pollSyntax sdlc timer poll mseconds Undo sdlc timer poll Sdlc window Undo sdlc xid sdlc-address Sdlc xid Annexg dce dte Frame Relay Configuration CommandsAnnexg Display fr compress Related commands fr compression frf9 Display fr dlci-switch # Display statistics about frame relay Inarp packets Related command fr inarp ExampleDisplay fr inarp-info Display fr interface Frame Display fr lmi-infoRange 0 to # Display information about all frame relay interfaces 375 Related command fr compression iphcDisplay fr iphc Fr map ip , fr inarp Display fr map-infoMappings or the one for the specified interface Whether dynamic address mapping operates normally Dlci = 100, IP Inarp Display fr map-info pppofr377 Fr dlci Display fr pvc-info1007 Statistics about data transmitted and received on them 379 Display fr statistics MTU Display interface mfr 381 Display mfr LID Description on the fields of the display mfr command 383 Display x25 templateSyntax display x25 template name Related command x25 template, x25-template View Subinterface point-to-point view Fr compression frf9Fr compression iphc Syntax fr compression frf9 Undo fr compression Undo fr dlci dlci-number Fr dlciUndo fr compression iphc Related command fr switching Fr dlci-switchUse the undo fr dlci command to cancel the configuration Undo fr dlci-switch in-dlci Syntax fr inarp ip dlci-number Undo fr inarp ip dlci-number Fr inarp 389 Fr interface-typeSyntax fr interface-type dce dte nni Undo fr interface-type Fr map ip , fr compression iphc Fr iphcFr lmi n391dte Tcp-include 391 Fr lmi n392dceSyntax fr lmi n392dce n392-value Undo fr lmi n392dce Syntax fr lmi n392dte n392-value Undo fr lmi n392dte Fr lmi n392dte Syntax fr lmi n393dte n393-value Undo fr lmi n393dte Fr lmi n393dceFr lmi n393dte Syntax fr lmi n393dce n393-value Undo fr lmi n393dce Syntax fr lmi t392dce t392-value Undo fr lmi t392dce Fr lmi t392dce Undo fr lmi type Fr lmi typeFr lmi type ansi nonstandard q933a bi-direction Fr map ip Fr map ppp Fr switchRelated command interface virtual-templateon Undo fr switch name Syntax fr switching Undo fr switching Fr switching 399 Interface mfrInterface serial Link-protocol fr ietf nonstandard Link-protocol fr Syntax mfr bundle-name name Undo mfr bundle-name Link-protocol fr mfrMfr bundle-name Syntax link-protocol fr mfr interface-number Syntax mfr fragment-size bytes Undo mfr fragment-size Mfr fragmentMfr fragment-size Syntax mfr fragment Undo mfr fragment 403 Mfr link-nameSyntax mfr link-name name Undo mfr link-name name Syntax mfr retry number Undo mfr retry Mfr retryMfr stateup-respond-addlink 405 Mfr timer ackSyntax mfr timer ack seconds Undo mfr timer ack Related command mfr timer hello, mfr retry Syntax mfr window-size number Undo mfr window-size Mfr timer helloSyntax mfr timer hello seconds Undo mfr timer hello Mfr window-size Related command fr inarp Reset fr inarpView Frame relay switching view Syntax reset fr inarp Example # Clear all the frame relay dynamic address maps Reset fr pvcRelated command fr lmi t392dce Syntax x25 template name Undo x25 template name X25-templateX25 template Syntax x25-template name Undo x25-template name Frame Relay Configuration Commands Display garp statistics Garp Configuration CommandsDisplay garp timer Syntax display garp timer interface interface-list View Ethernet interface view, port group view Garp timerRelated command garp timer, garp timer leaveall Example # Display Garp timers on port Ethernet 1/0 Timer Lower limit Upper limit Garp timer leaveallRelated command display garp timer Dependencies of Garp timers Display gvrp statistics Reset garp statisticsReset garp statistics interface interface-list Syntax display gvrp statistics interface interface-list Gvrp Configuration CommandsDisplay gvrp statistics Syntax gvrp Related command display gvrp statusDisplay gvrp status Gvrp Display garp statistics Gvrp registrationGvrp registration fixed forbidden normal Undo gvrp registration Gvrp Configuration Commands Link-protocol hdlc Hdlc Configuration CommandsTimer hold Timer hold seconds Hdlc Configuration Commands X25 hunt-group Lapb and X.25 Configuration CommandsChannel Lapb and X.25 Configuration Commands Lapb DCE Description on the fields of the display interface command423 Display x25 alias-policy Display x25 cug local-cug local-cug-number network-cug Related command x25 alias-policy ExampleDisplay x25 cug Display x25 hunt-group-info Syntax display x25 map Related command x25 hunt-groupDisplay x25 map Syntax display x25 pad pad-id Description on the fields of the display x25 map commandDisplay x25 pad Example # Display the X.25 address mapping table Syntax display x25 switch-table svc dynamic static Display x25 switch-table pvcDisplay x25 switch-table svc Syntax display x25 switch-table pvc Syntax display x25 vc lci Related command x25 switch svcExample # Display X.25 SVC static switching table Display x25 vc Data 0/0 Interrupt 0/0 SVC Description on the fields of the display x25 vc command431 Display x25 xot Display x25 x2t switch-table Difference between N1 Lapb max-frameSyntax lapb max-frame n1-value Undo lapb max-frame 433 Parameter 8 Modulo Related command lapb window-sizeLapb modulo Lapb retry Syntax lapb window-size k-valueundo lapb window-size Lapb timerUndo lapb timer t1 t2 t3 Lapb window-size Link-protocol lapb dce dte ip multi-protocol Link-protocol lapbLapb modulo Link-protocol x25 dce dte ietf nonstandard Pad Reset Reset xot Undo translate ip ip-addressport port-number Reset lapb statisticsSyntax reset lapb statistics Translate ip Parameter x.121-address X.121 address TranslateUndo translate x25 x.121-address 441 X25 alias-policy Description on the user facility option X25 call-facility Option Description Window-size X25 cug-serviceRelated command x25 map, x25 modulo 443 Related command x25 local-cug X25 default-protocol 445 X25 hunt-group X25 ignore calling-address X25 ignore called-address 447 X25 local-cug Undo x25 map ip compressedtcp protocol-address Related command x25 call-facility,x25 cug-serviceX25 map Protocols such as Routing Information Protocol Send-delay delay-time449 Option Description Broadcast Syntax x25 modulo 8 Undo x25 modulo X25 modulo 451 X25 packet-size# Set the modulo on the X.25 interface Serial 2/0 to Undo x25 packet-size Description on PVC attribute option X25 pvcUndo x25 pvc pvc-number 453 X25 queue-lengthSyntax x25 queue-length queue-length Undo x25 queue-length X25 receive-threshold Related command x25 window-size 455 X25 response called-addressX25 response calling-address X25 reverse-charge-accept Related command x25 map X25 roa-list X25 switch pvcRelated command x25 call-facility,x25 map Undo x25 switch pvc pvc-number1 Lapb and X.25 Configuration Commands 459 X25 switch svc121 mode matching rules Characters Input rules Input rules of X.121 address mode matching stringNumber SVC route number 461 X25 switch svc hunt-group Related command display x25 switch-table svc X25 switch svc xot Syntax x25 switching Undo x25 switching X25 switching Syntax x25 timer hold minutes Undo x25 timer hold X25 timer holdX25 timer idle Example # Enable X.25 switching function 465 X25 timer tx0Syntax x25 timer tx0 seconds Undo x25 timer tx0 Related command x25 timer tx1, x25 timer tx2, x25 timer tx3 Related command x25 timer tx0, x25 timer tx2, x25 timer tx3 X25 timer tx1X25 timer tx2 Syntax x25 timer tx1 seconds Undo x25 timer tx1 Related command x25 timer tx0, x25 timer tx1, x25 timer tx2 X25 timer tx3Related command x25 timer tx0, x25 timer tx1, x25 timer tx3 Syntax x25 timer tx3 seconds Undo x25 timer tx3 Syntax x25 vc-per-map count Undo x25 vc-per-map X25 vc-per-mapX25 vc-range 469 X25 window-sizeUndo x25 window-size Syntax x25 x121-address x.121-address Undo x25 x121-address X25 x121-addressX25 xot pvc 471 Related command display x25 vc, x25 switchingUndo x25 pvc pvc-number1 XOT channel parameter option X29 timer inviteclear-time Syntax display lacp system-id Link Aggregation Configuration CommandsDisplay lacp system-id Display link-aggregation interface Link Aggregation Configuration Commands 475 Display link-aggregation summarySyntax display link-aggregation summary AL ID Display link-aggregation verboseExample # Display the link aggregation group summary Syntax display link-aggregation verbose agg-id 477 Lacp port-priority 479 Lacp system-priorityLink-aggregation group description Example # Assign Lacp priority 64 to a port Port link-aggregation group Link-aggregation group modeRelated command display link-aggregation verbose Related command display link-aggregation summary Port-group aggregation agg-id Reset lacp statisticsRelated command Display link-aggregation verbose Example Port-group aggregation Example # Clear statistics about Lacp on all ports Related command display link-aggregation interface Debugging lacp packet Link Aggregation Debugging CommandsView User view Default Level 1 Monitor level Link Aggregation Debugging Commands 485 Device sent an Lacp protocol packet through Ethernet 1/1Length of the Terminator field in the protocol packet is Device received an Lacp protocol packet through Ethernet 1/1 487 Debugging lacp state Syntax debugging link-aggregation error Debugging link-aggregation error 489 ErrorDebugging link-aggregation event Syntax debugging link-aggregation event Operation key of port Ethernet 1/1 Key 1 was removed Aggregation group 10 existed. It contained Ethernet 1/1# Remove aggregation group Aggregation group 10 was removed Modem auto-answer Modem Configuration CommandsModem Syntax modem timer answer time Undo modem timer answer Modem timer answer With caution under the guidance of technicians Sendat command can issue only one AT command at a timeSendat Specifies the communication standard to be adopted 495 Service modem-callbackExample # Send dialing command to call number Syntax service modem-callback Example # Enable the callback function Undo service modem-callback Syntax display mirroring-group groupid local Port Mirroring Configuration CommandsDisplay mirroring-group Mirroring-group Undo mirroring-group groupid local Mirroring-group mirroring-port 499 Mirroring-group monitor-port # Add POS 5/1 to local port mirroring group Mirroring-port 501 Monitor-port# Add Cpos 6/1 to local port mirroring group Port Mirroring Configuration Commands Syntax display interface mp-group mp-number PPP and MP Configuration 31 CommandsDisplay interface mp-group Example # View the information about VT Related command interface virtual-templateDisplay interface virtual-template Syntax display interface virtual-template number 505 Description on the fields of the display ppp mp commandDisplay ppp mp Link-protocol ppp , ppp mp For description on the output fields, refer to Table Display virtual-access 507 Interface mp-group Ip address ppp-negotiate Interface virtual-template Link-protocol ppp Ppp account-statistics enablePpp account-statistics enable Undo ppp account-statistics enable Chap, pap Authentication modes. Use either mode Ppp authentication-modePpp authentication-mode chap pap call-in domain isp-name Undo ppp authentication-mode Syntax ppp chap user username Ppp chap passwordRelated command ppp authentication-modechap Ppp chap user Undo ppp chap user Related command ppp authentication-modePpp ipcp dns Syntax ppp ipcp dns request Undo ppp ipcp dns request Ppp ipcp dns admit-anyPpp ipcp dns request Syntax ppp ipcp dns admit-any Undo ppp ipcp dns admit-any Ppp ipcp remote-address forced Related command remote address 515 Ppp lqcUndo ppp lqc Undo ppp mp Ppp mpPpp mp binding-mode Syntax ppp mp Undo ppp mp max-bind Related command Ppp mp user ExamplePpp mp max-bind Ppp mp max-bind max-bind-num Undo ppp mp min-bind Related command Ppp mp ExamplePpp mp min-bind Ppp mp min-bind min-bind-num Undo ppp mp min-fragment Related command dialer threshold onPpp mp min-fragment Ppp mp min-fragment size Example # Add interface Serial 3/0 to MP-group Ppp mp mp-groupPpp mp user Syntax ppp mp mp-group number Undo ppp mp 521 Related command ppp mp and ppp mp max-bindPpp mp virtual-template Syntax ppp mp virtual-template number Undo ppp mp Ppp pap local-user Ppp timer negotiateRelated command local-useron page 1940, password on Syntax ppp timer negotiate seconds Undo ppp timer negotiate 523 Remote addressUndo remote address Timer hold Display ppp compression iphc tcp PPP Link Efficiency Mechanism Configuration CommandsDisplay ppp compression iphc rtp Syntax ip tcp vjcompress Undo ip tcp vjcompress Display ppp compression stac-lzsIp tcp vjcompress 527 Ppp compression iphc Ppp compression iphc rtp-connections 529 Ppp compression iphc tcp-connectionsPpp compression stac-lzs Syntax ppp mp lfi Undo ppp mp lfi Ppp mp lfi 531 Ppp mp lfi delay-per-fragReset ppp compression iphc PPP Link Efficiency Mechanism Configuration Commands Display pppoe-server session all packet Pppoe Server Configuration CommandsDisplay pppoe-server session Pppoe-server log-information off Pppoe-server bind 535 Pppoe-server max-sessions local-macPppoe-server max-sessions remote-mac Undo pppoe-server max-sessions total Reset pppoe-serverPppoe-server max-sessions total Pppoe-server max-sessions total number 537 Pppoe Server Configuration Commands Display pppoe-client session Pppoe Client Configuration Commands Pppoe-client dial-bundle-number Related command pppoe-client Reset pppoe-clientRelated command Reset pppoe-client Reset pppoe-client all dial-bundle-number number Sysname reset pppoe-client all Debugging ppp PPP Debugging Commands Description on the fields of the debugging ppp event command 545 Description on the fields of the debugging ppp ipcp command LCP moved from the starting state to the reqsent state Description on the fields of the debugging ppp ipcp commandLCP moved from the initial state to the starting state 547 PPP Debugging Commands Bridge aging-time Bridging Configuration CommandsBridge bridge-set enable Syntax bridge bridge-setenable Undo bridge bridge-setenable Syntax bridge enable Undo bridge enable Bridge enableExample # Enable bridge set # Enable IP bridging on bridge set 551 Example # Enable bridgingBridge learning Bridge mac-address Bridge routing Syntax bridge-set bridge-set Undo bridge-set bridge-set Bridge routing-enableSyntax bridge routing-enable Undo bridge routing-enable Bridge-set Display bridge address-table Dynamic S--STATIC Display bridge informationSyntax display bridge information bridge-set bridge-set 555 Display bridge traffic 557 Display interface bridge-templateSyntax display interface bridge-template interface-number UP/DOWN Fr map bridgeSyntax fr map bridge dlci broadcast Undo fr map bridge dlci Parameters Related command display fr map-infoonBridge routing-enable Interface bridge-template Syntax mac-address mac-address Undo mac-address Related command interface bridge-templateMac-address bridge-template interface view Map bridge-group 561 Reset bridge address-tableReset bridge traffic Display x25 map on X25 map bridgeX25 map bridge x121-address x.121-address broadcast Undo x25 map bridge x121-address x.121-address Undo dialer isdn-leased 128k number Isdn Configuration CommandsDialer isdn-leased Isdn BRI interface view Dialer isdn-leased 128k number Display isdn call-info Display isdn active-channel 565 Example # Display the current state of Isdn interface 2/0 Display isdn call-record 567 Display isdn parameters Kpri Display isdn spidIsdn Kbri 569 Isdn bch-local-manage Isdn caller-number Bch-local-manage command on the user sideChannels in ascending order by default Isdn bch-select-way Undo isdn check-called-number check-index Isdn callingIsdn check-called-number Undo isdn calling Syntax isdn check-time date-time Undo isdn check-time Isdn check-time Syntax isdn ignore connect-ack Isdn crlengthIsdn ignore connect-ack Undo isdn crlength Isdn ignore hlc Settings must be the same as those on the exchangeIsdn ignore hlc Undo isdn ignore connect-ack Undo isdn ignore llc Isdn ignore llcVoice calls placed on the BRI interface 1/0 Isdn ignore llc Undo isdn ignore sending-complete incoming outgoing ConfiguredIsdn ignore sending-complete Isdn ignore sending-complete incoming outgoing Value range Default Timer-name Seconds Isdn L3-timerUndo isdn L3-timer all timer-name Description of Q931 timers View Isdn BRI interface Isdn link-modeIsdn number-property Syntax isdn link-mode p2p Undo isdn link-mode Protocol Field Bit value Definition Type Code scheme Types and code schemes of Isdn numbers579 Qsig NTT 581 Set the type and code scheme of Isdn numbers Calls Isdn overlap-sending 583 Isdn pri-slipwnd-size Syntax isdn protocol-type protocol Undo isdn protocol-type Isdn protocol-modeIsdn protocol-type View Isdn BRI interface view Isdn q921-permanentExample # Apply Isdn Etsi on interface BRI 1/0 Syntax isdn q921-permanent Undo isdn q921-permanent Syntax isdn spid autotrigger Isdn send-restartIsdn spid autotrigger Syntax isdn send-restart Undo isdn send-restart Syntax isdn spid nit Undo isdn spid nit Isdn spid timerSyntax isdn spid timer seconds Undo isdn spid timer Isdn spid nit Undo isdn spid service Isdn spid serviceIsdn spid service audio data speech Syntax isdn spid1 spid LDN Isdn spid resendIsdn spid1 Syntax isdn spid resend times Undo isdn spid resend Syntax isdn spid2 spid LDN Undo isdn spid2 Isdn spid2Undo isdn spid1 LDN Local dialing number, a string of 1 to 30 digits Configuration of the Isdn calling commandThis command applies only on NI-compliant BRI interfaces Spid String of 1 to 20 digits Syntax isdn two-tei Isdn two-tei Syntax permanent-active Undo permanent-active Permanent-activeUndo isdn two-tei View BRI interface view Syntax power-source Undo power-source Power-source 595 # Bring up BRI 2/0 Isdn Configuration Commands Syntax active region-configuration Mstp Configuration CommandsActive region-configuration Check region-configuration Information Display stpPort number Brief Displays brief information 599 Related commands reset stp Root guard action Display stp abnormal-portDisplay stp abnormal-port Abnormally blocked ports Syntax display stp instance instance-id history Display stp down-portDisplay stp history Syntax display stp down-port Syntax display stp region-configuration Display stp region-configuration Syntax display stp root Related commands stp region-configurationDescription on the fields of the display stp root command Display stp root Tree instance, in port name order Display stp tcModel Sent Syntax region-name name Undo region-name InstanceRegion-name Examples # Map Vlan 2 to MST instance Display stp Reset stpReset stp interface interface-list Syntax revision-level level Undo revision-level Syntax stp enable disable Undo stpRevision-level Stp Stp bpdu-protection Related commands stp modeExamples # Enable the Mstp feature globally # Disable Mstp on port Ethernet 1/1 Stp compliance Stp bridge-diameter Stp config-digest-snooping Stp cost Undo stp edged-port Stp edged-port enable disableOr undo stp edged-port enable command to non-edge port Stp edged-port Syntax stp loop-protection Undo stp loop-protection Examples # Configure port Ethernet 1/1 as a non-edge portStp loop-protection Stp max-hops Syntax stp mcheck Stp mcheck Stp mcheck , stp Stp modeStp no-agreement-check 802.1D-1998 Examples # Enable No Agreement Check on Ethernet 1/1Stp pathcost-standard View System view Parameters 617 Stp point-to-point Stp port-log 619 Stp port priority Undo stp instance instance-id priority Stp priorityStp instance instance-id priority priority Stp root primary Stp region-configuration Stp instance instance-id root secondary Stp root secondary Syntax stp root-protection Undo stp root-protection Syntax stp tc-protection enable Stp tc-protection disableStp root-protection Stp tc-protection Stp tc-protection threshold Stp timer forward-delay 625 Stp timer helloSyntax stp timer hello centi-seconds Undo stp timer hello Stp timer max-age 627 Stp timer-factorSyntax stp timer-factor number Undo stp timer-factor Syntax vlan-mapping modulo modulo Stp transmit-limitVlan-mapping modulo 629 Examples # Map VLANs to MSTIs as per the modulo value Mstp Configuration Commands Syntax display interface vlan-interface vlan-interface-id Vlan Configuration CommandsDisplay interface vlan-interface # Display the information of VLAN-interface Vlan-interface-id Vlan interface IDVlan interfaces will be displayed # Display Vlan 3 information Related command vlanDisplay vlan Example # Display Vlan 2 information Example # Create Vlan interface Related command display interface vlan-interfaceDescription on the fields of the display vlan command Interface vlan-interface 635 Related command display ip interface onIp address View Vlan interface view Vlan 637 Related command display vlanExample # Enter Vlan 2 view # Create Vlan 4 through Vlan Vlan Configuration Commands Port PORT-BASED Vlan Configuration CommandsPort access vlan Syntax port access vlan vlan-id Undo port access vlan Syntax port hybrid pvid vlan vlan-id Undo port hybrid pvid Related command port link-typePort hybrid pvid vlan 641 Port hybrid vlan Port trunk permit vlan Port link-type 643 Port trunk pvid vlanSyntax port trunk pvid vlan vlan-id Undo port trunk pvid Related command port link-type Voice Vlan Configuration Commands Voice vlan Voice vlan enable ExampleSyntax voice vlan vlan-idenable Display voice vlan state Syntax voice vlan aging minutes Undo voice vlan aging Undo voice vlan enableRelated command display voice vlan state Voice vlan aging Voice vlan mac-address Voice vlan enableSyntax voice vlan enable Undo voice vlan enable Display voice vlan oui Example Ffff-f000-0000Range of 1 to 30 characters Be a broadcast, multicast or address of all 0s or all fs Syntax voice vlan mode auto Undo voice vlan mode auto Voice vlan mode autoVoice vlan security enable 651 Example # Disable the security mode of the voice Vlan Voice Vlan Configuration Commands Display port-isolate group Port Isolation Configuration CommandsPort-isolate enable Syntax port-isolate enable Undo port-isolate enable Port Isolation Configuration Commands Standby routing-rule Dynamic Route Backup Configuration CommandsStandby routing-group Standby timer routing-disable Syntax display interface loopback number Logical Interface Configuration CommandsBroadcast-limit link Display interface loopback Syntax display interface mfr mfr-number Related command interface loopbackExample # View the status of Loopback LMI Dlci Related command interface mfrExample # View the state information about MFR 659 Example # View the state information of MP-group Related command interface mp-group Syntax display interface null Related command interface nullDisplay interface null Display interface virtual-ethernet Example # View the state information about VT Related command interface virtual-ethernetExample # View the state information about VE 663 Description of the fields of the display mfr command Interface, state of the link layer, and the name 665 Interface ethernet Example # Create Loopback Related command display interface loopbackInterface loopback Interface null Interface nullExample # Create MFR Example # Create MP-group Example # Enter Null 0 interface view Related command display interface nullInterface virtual-ethernet 669 Logical Interface Configuration Commands System view Cpos Interface Configuration CommandsController cpos Display controller cpos cpos-number Display controller cpos 673 This table, FRED, COFA, and SEF are alarm errors AERRsPossible error types Syntax display controller cpos cpos-numbere1 e1-number Display controller cpos e1Some information about T1 channels is omitted 675 Display controller cpos t1Syntax display controller cpos cpos-numbert1 t1-number VC-3 677 Example # Bundle timeslots on E1 channel E1 set clock 679 Related command display controller cpos e1Example # Enable external payload loopback on E1 channel Syntax e1 e1-numberunframed undo e1 e1-numberunframed Syntax e1 e1-numbershutdown undo e1 e1-numbershutdown Syntax frame-format sdh sonet undo frame-format Undo flag j0 j1 c2Display controller cpos Syntax multiplex mode au-3 au-4 undo multiplex mode Multiplex modeUse the undo loopback command to remove a loopback # Enable external loopback on interface Cpos 1/0 683 Related command frame-formatExample # In SDH mode, multiplex AUG to AU-3 Example # Bundle timeslots on T1 channel Example # Shut down Cpos physical interface 1/0 685 Syntax t1 t1-numbershutdown Undo t1 t1-numbershutdown Related command display controller cpos t1Example # Enable external loopback on T1 channel 687 Syntax t1 t1-numberunframed Undo t1 t1-numberunframed Cpos Interface Configuration Commands Arp max-learning-num ARP Configuration CommandsArp check enable Syntax arp check enable Undo arp check enable Arp static Display arp Arp timer agingRelated command reset arp, display arp Related command display arp timer aging # Display the number of all ARP entries Related command arp static, reset arpDescription on the fields of the display arp command Arp timer aging Display arp timer agingArp static , and reset arp Example Display arp timer aging Display arp vpn-instance Naturemask-arp enableRelated command arp static and reset arp Syntax naturemask-arp enable Undo naturemask-arp enable Arp static and display arp Reset arpSpecified by the argument interface-type interface-number ARP Configuration Commands Gratuitous-arp-sending enable Gratuitous ARP Configuration CommandsGratuitous-arp-sending enable Gratuitous-arp-learning enable Sysname system-view Sysname gratuitous-arp-learning enable Display arp source-suppression ARP Source Suppression Configuration CommandsArp source-suppression enable Arp source-suppression limit Description on fields of display arp source-suppression Related command display arp source-suppressionDisplay arp source-suppression Syntax display arp source-suppression Arp authorized time-out Authorized ARP Configuration CommandsArp authorized enable Syntax arp authorized enable Undo arp authorized enable Authorized ARP Configuration Commands Related command display proxy-arp Proxy ARP Configuration CommandsProxy-arp enable Local-proxy-arp enable Display proxy-arp Related command display local-proxy-arpProxy-arp enable Local-proxy-arp enable Dhcp Server Configuration Commands Syntax dhcp enable Undo dhcp enable Bootfile-nameDhcp enable Syntax bootfile-name bootfile-name Undo bootfile-name 707 Dhcp select server global-poolDhcp server detect Syntax dhcp server detect Undo dhcp server detect Dhcp server ip-pool Dhcp server forbidden-ip Example # Create the Dhcp address pool identified by Dhcp server ping timeoutRelated command dhcp enable Dhcp server ping packets Syntax dhcp update arp Undo dhcp update arp Dhcp server relay information enableDhcp update arp Display dhcp server conflict all ip ip-address Reset dhcp server conflictDisplay dhcp server conflict Display dhcp server expired Syntax display dhcp server forbidden-ip Display dhcp server free-ipDisplay dhcp server forbidden-ip Display dhcp server free-ip Information of Dhcp address pools or an IP address Reset dhcp server ip-in-useDisplay dhcp server ip-in-use Binding information of all address pools is displayed Example # Display the statistics on the Dhcp server Reset dhcp server statisticsDisplay dhcp server statistics Syntax display dhcp server statistics 715 Display dhcp server treeDisplay dhcp server tree all pool pool-name Information of Dhcp address pools Undo dns-list ip-addressall Dns-list Expired Related command dhcp server ip-poolDomain-name Gateway-list 719 Netbios-typeRelated command dhcp server ip-pooland netbios-type Nbns-list Undo network Related command dhcp server ip-pooland nbns-listNetwork 721 OptionUndo option code Reset dhcp server statistics Reset dhcp server conflictReset dhcp server ip-in-use 723 Related command display dhcp server statisticsStatic-bind client-identifier Example # Clear the statistics of the Dhcp server Static-bind ip-address 725 Static-bind mac-addressTftp-server domain-name View Dhcp address pool view Voice-configUndo voice-config as-ip fail-over ncp-ip voice-vlan Tftp-server ip-address 727 Dhcp Server Configuration Commands Dhcp relay address-check Dhcp Relay Agent Configuration CommandsDhcp Snooping cannot be configured on the Dhcp relay agent Syntax dhcp relay address-check disable enable Dhcp relay information format Dhcp relay information enable Undo dhcp relay information strategy Dhcp relay information strategyDhcp relay information strategy drop keep replace Undo dhcp relay security ip-address all dynamic static Dhcp relay release ipDhcp relay security static Syntax dhcp relay release ip client-ip 733 Related command display dhcp relay securityDhcp relay security tracker Undo dhcp relay server-detect Dhcp relay server-detectDhcp relay server-group Dhcp relay server-detect 735 Related command display dhcp relay server-groupDhcp relay server-select Undo dhcp select relay Dhcp update arpDhcp select relay Dhcp select relay Groups correlated to an interface or all interfaces Display dhcp relayDisplay dhcp relay security Server group that a specified interface corresponds to Information about bindings of Dhcp relay agents Display dhcp relay security statisticsDisplay dhcp relay security tracker Display dhcp relay security statistics Syntax display dhcp relay server-group group-idall Display dhcp relay server-groupDisplay dhcp relay statistics Interval is 10 seconds Server Client Display dhcp relay statistics Reset dhcp relay statisticsReset dhcp relay statistics server-group group-id Which to remove statistics from the relay agent Dhcp Relay Agent Configuration Commands Dhcp Client Configuration Commands Ip address dhcp-alloc Description on fields of the display dhcp client command 745 Dhcp Client Configuration Commands Dhcp-snooping trust Dhcp Snooping Configuration CommandsRelated command display dhcp-snooping Dhcp-snooping Dhcp-snooping Related command display dhcp-snooping trustDisplay dhcp-snooping Display dhcp-snooping trust 749 Related command dhcp-snooping trust ExampleTrusted ports # Display information about trusted ports Dhcp Snooping Configuration Commands Including sub-interfaces and Vlan interfaces Bootp Client Configuration CommandsBootp client Display information about Bootp clients on all interfaces Description on fields of the display bootp client command Ip address bootp-allocSyntax ip address bootp-alloc Undo ip address bootp-alloc Related command display bootp client Debugging dhcp server Dhcp Debugging CommandsDebugging dhcp server all error event packet Undo debugging dhcp server all error event packet Dhcp ACK Dhcp NAK DHCPmessagetype 755 Checking for an expired leaseDHCP-DISCOVER packet received DHCP-REQUEST message received Checking whether the IP address 22.0.0.2 is in use Sending a DHCP-ACK message Debugging dhcp relay Sysname Terminal debugging 759 Then broadcast it Debugging dhcp client all error event packetUndo debugging dhcp client all error event packet Debugging dhcp client 761 State of the Dhcp client is changed from Halt to Init Head 763 ARP message sent Dhcp client starts address conflict detection using ARP Dns domain Example DNS Configuration CommandsDisplay dns domain Display dns dynamic-host TTL Display dns proxy tableSyntax display dns proxy table Syntax display dns server dynamic Related command dns serverDisplay dns server Display ip host Dns domain Dns proxy enableRelated command display dns domain Syntax dns proxy enable Undo dns proxy enable Syntax dns server ip-address Undo dns server ip-address Dns resolveDns server Syntax dns resolve Undo dns resolve Syntax reset dns dynamic-host Reset dns dynamic-hostRelated command display dns server Related command display ip host 771 Related command display dns dynamic-host DNS Configuration Commands Firewall-denied interior IP Accounting Configuration CommandsDisplay ip count Display ip count inbound-packets outbound-packets exterior Display ip count rule Ip count enableSyntax ip count enable Undo ip count enable Description on fields of the display ip count rule command 775 Example # Enable IP accountingIp count exterior-threshold Ip count firewall-denied Ip count inbound-packets 777 Ip count interior-thresholdExample # Count incoming IP packets on Ethernet1/0 # Specify not to count incoming IP packets on Ethernet1/0 Ip count rule Ip count outbound-packets Syntax reset ip count all exterior firewall interior Ip count timeoutReset ip count Syntax ip count timeout minutes Undo ip count timeout # Clear the statistics of all IP packets All Clears all statisticsExterior Clears the statistics from the exterior table Interior Clears the statistics from the interior table Display ip interface IP Addressing Configuration Commands Description on fields of the display ip interface command 783 Related command display ip interfaceDisplay ip interface brief Example # Display brief information about Ethernet 1/0 Displayed 785 Ip address unnumbered IP Addressing Configuration Commands Display fib IP Performance Configuration Commands # Display FIB information passing the IP prefix list abc0 Description on the fields of the display fib command# Display FIB information passing ACL Syntax display fib statistics Display fib ip-addressDisplay fib statistics For description about the above output, refer to Table Example # Display Icmp statistics Display icmp statisticsSyntax display icmp statistics # Display all socket information Display ip socket100 3072 Syntax display ip statistics Description on the fields of the display ip socket commandDisplay ip statistics 793 Display tcp statisticsExample # Display statistics of IP packets Syntax display tcp statistics Example # Display statistics of TCP traffic Related command display tcp status and reset tcp statistics 795 Display tcp status Related command reset udp statisticsDisplay tcp status Display udp statistics Undo ip forward-broadcast Ip forward-broadcastIp forward-broadcast acl acl-number Ip ttl-expires enable Ip redirects enable Reset tcp statistics Ip unreachables enableReset ip statistics Syntax reset udp statistics Reset udp statisticsTcp anti-naptha enable Related command display tcp statistics Tcp state Tcp mss Syntax tcp syn-cookie enable Undo tcp syn-cookie enable Tcp syn-cookie enableRelated command tcp anti-naptha enable This support for this command varies with devices 803 Tcp timer check-stateTcp timer fin-timeout Example # Enable the SYN Cookie feature Related command tcp timer fin-timeoutand tcp window Tcp timer syn-timeoutRelated command tcp timer syn-timeoutand tcp window 805 Tcp windowSyntax tcp window window-size Undo tcp window IP Performance Configuration Commands View policy-based-route view IP Unicast Policy Routing Configuration CommandsApply default output-interface Apply ip-address default next-hop Undo apply ip-address next-hop ip-address ip-address Parameters ip-address IP address of the default next hopApply ip-address next-hop 809 Apply ip-precedenceExamples # Set the next hop to 1.1.1.1 for matched packets IP precedences and the corresponding keywords Syntax display ip policy-based-route Apply output-interfaceDisplay ip policy-based-route 811 Display ip policy-based-route setup Routing statistics Local Displays statistics of enabled system policy routingDisplay ip policy-based-route statistics Interface-number Syntax display policy-based-route policy-name Related commands if-matchpacket-lengthDisplay policy-based-route If-match acl Ip local policy-based-route Related commands if-match aclIf-match packet-length Policy-based-route Related commands policy-based-routeRelated commands ip local policy-based-route Ip policy-based-route Syntax reset policy-based-route statistics policy-name Reset policy-based-route statisticsRelated commands if-match acl and if-matchpacket-length 817 IP Unicast Policy Routing Configuration Commands Display udp-helper server UDP Helper Configuration CommandsReset udp-helper packet Reset udp-helper packet Udp-helper port Udp-helper enableSyntax udp-helper enable Undo udp-helper enable 821 Related command display udp-helper serverUdp-helper server UDP Helper Configuration Commands Undo ip urpf Urpf Configuration CommandsIp urpf loose strict allow-default-route acl acl-number Ip urpf Urpf Configuration Commands Display ip fast-forwarding cache Fast Forwarding CommandsDisplay ip fast-forwarding cache Ip fast-forwarding Fast Forwarding Commands 827 Reset ip fast-forwarding cacheSyntax reset ip fast-forwarding cache Fast Forwarding Commands Syntax display dns ipv6 dynamic-host IPV6 Basics Configuration CommandsDisplay dns ipv6 dynamic-host Display dns ipv6 server Syntax display ipv6 fib ipv6-address Display ipv6 fibExample # Display IPv6 DNS server information Syntax display ipv6 fibcache Description on fields of the display ipv6 fib commandDisplay ipv6 fibcache Display ipv6 host Display ipv6 interface 833 Shutdown command Display ipv6 neighbors Static vlan vlan-id count Display ipv6 neighbors count Syntax display ipv6 pathmtu ipv6-addressall dynamic static Description on fields of the display ipv6 pathmtu commandDisplay ipv6 pathmtu Display ipv6 socket 837 Description on fields of the display ipv6 socket commandDisplay ipv6 statistics Syntax display ipv6 statistics Description on fields of the display ipv6 statistics command 839 # Display the statistics of IPv6 TCP connections Display tcp ipv6 statisticsDisplay tcp ipv6 statistics Statistics 841 Syntax display tcp ipv6 status Display tcp ipv6 status TCP6CB Display udp ipv6 statisticsSyntax display udp ipv6 statistics 843 Undo ipv6 Dns server ipv6Ipv6 Syntax ipv6 845 Ipv6 addressIpv6 address auto link-local Ipv6 address link-local Ipv6 address eui-64 847 Ipv6 fibcacheIpv6 fib-loadbalance-type hash-based Syntax ipv6 fibcache Undo ipv6 fibcache Ipv6 host Ipv6 icmp-error 849 Ipv6 icmpv6 multicast-echo-reply enableIpv6 mtu Syntax ipv6 mtu mtu-size Undo ipv6 mtu Undo ipv6 nd autoconfig managed-address-flag Ipv6 nd autoconfig managed-address-flagIpv6 nd autoconfig other-flag Ipv6 nd autoconfig managed-address-flag Syntax ipv6 nd hop-limit value Undo ipv6 nd hop-limit Ipv6 nd dad attemptsIpv6 nd hop-limit Syntax ipv6 nd dad attempts value Undo ipv6 nd dad attempts Ipv6 nd nud reachable-time Ipv6 nd ns retrans-timer 853 Ipv6 nd ra haltSyntax ipv6 nd ra halt Undo ipv6 nd ra halt On a router # Suppress RA messages on Ethernet1/0 Undo ipv6 nd ra prefix ipv6-prefix Ipv6 nd ra intervalIpv6 nd ra prefix Undo ipv6 nd ra interval 855 Ipv6 nd ra router-lifetime Ipv6 neighbor 857 Ipv6 neighbors max-learning-numIpv6 pathmtu Undo ipv6 pathmtu ipv6-address Ipv6 pathmtu age Reset dns ipv6 dynamic-hostRelated command display ipv6 pathmtu Syntax reset dns ipv6 dynamic-host Reset ipv6 pathmtu Reset ipv6 fibcacheReset ipv6 neighbors ICMPv6 packets Reset ipv6 statisticsReset tcp ipv6 statistics Reset udp ipv6 statistics 861 Tcp ipv6 timer fin-timeoutTcp ipv6 timer syn-timeout Example # Clear the statistics of all UDP packets Syntax tcp ipv6 window size Undo tcp ipv6 window Tcp ipv6 window Display natpt address-group NAT-PT Configuration CommandsDisplay natpt address-group Display natpt address-mapping Syntax display natpt aging-time Display natpt aging-time 865 Example # Display all NAT-PT configuration informationDisplay natpt all Display natpt all Syntax display natpt frag-sessions Display natpt frag-sessions Display natpt statistics Display natpt sessionDisplay natpt statistics Syntax display natpt session all icmp tcp udp Undo natpt address-group group-number Natpt address-group Natpt aging-time Syntax natpt max-session max-number Undo natpt max-session Natpt enableSyntax natpt enable Undo natpt enable Natpt max-session 871 Example # Configure a NAT-PT prefixNatpt prefix Undo natpt prefix natpt-prefix Undo natpt turn-off tos Natpt turn-off tosNatpt turn-off traffic-class Natpt turn-off tos 873 Natpt v4bound dynamicNatpt v4bound static Natpt v6bound dynamic Undo natpt v6bound static ipv6-addressipv4-address Reset natpt dynamic-mappingsSyntax reset natpt dynamic-mappings Natpt v6bound static # Clear all NAT-PT statistics information Reset natpt statisticsReset natpt statistics Dual Stack Configuration Commands Ethernet interface view Ipv6 address auto link-localAutomatically create a link-local address for an interface Automatically created link-local address 879 Example # Configure a link-local address on Ethernet 1/1 Dual Stack Configuration Commands Undo destination Tunneling Configuration CommandsRelated command interface tunnel and source Destination Example # Display information of the interface tunnel Display interface tunnelSyntax display interface tunnel number 883 Display ipv6 interface tunnelSyntax display ipv6 interface tunnel number Syntax interface tunnel number Encapsulation-limitInterface tunnel Syntax encapsulation-limit number Undo encapsulation-limit 885 Undo interface tunnel numberExample # Create the interface tunnel Undo source Related command interface tunnel and destinationSource Undo tunnel-protocol Tunnel-protocolIpv4-ipv6 Tunneling Configuration Commands View IPv6 policy-based-route view IPV6 Unicast Policy Routing Configuration CommandsApply destination-based-forwarding Apply ipv6-address default next-hop Preferences and the corresponding keywords Apply ipv6-address next-hopApply ipv6-precedence Example # Set a next hop of 11 for matched IPv6 packets Apply output-interface Display ipv6 policy-based-route Display ipv6 config policy-based-routeSyntax display ipv6 config policy-based-route policy-name Display ipv6 policy-based-route Local Displays system policy routing information Display ipv6 policy-based-route setup Syntax if-match acl6 acl6-number Undo if-match acl6 Related command if-matchpacket-lengthDisplay ipv6 policy-based-route statistics If-match acl6 Example # Permit the packets matching ACL Related command if-match acl6Ipv6 local policy-based-route 897 Related command ipv6 local policy-based-routeIpv6 policy-based-route interface view Ipv6 policy-based-route system view IPV6 Unicast Policy Routing Configuration Commands Syntax auto-close time Undo auto-close Terminal Access Configuration CommandsAuto-close Auto-link Syntax bind vpn-instance vpn-name Undo bind vpn-instance Bind vpn-instance Syntax data read block Undo data read block Data protect router-unixData read block View Terminal template view Display rta Data send delaySyntax data send delay milliseconds Undo data send delay 903 # Display brief information about TTY TTY 905 # Display all the information about terminal accessDescription on the fields of the display rta all command # Display statistics about terminal Syntax driverbuf save Undo driverbuf save # Display terminal access statisticsDriverbuf save Driverbuf size 907 Idle-timeoutSyntax idle-timeout seconds Undo idle-timeout Undo driverbuf size Syntax menu hotkey ascii-code&1-3 Undo menu hotkey Related command print information and print menuMenu hotkey Menu screencode 909 Print connection-infoSyntax print connection-info Undo print connection-info Print menu Related command print informationRelated command print connection-infoand print menu Print information Terminal template view Print languageRedrawkey Print language chinese english Reset rta statistics terminal-number Reset rta connectionReset rta statistics Rta bind ResetkeyRelated command display rta Undo resetkey Rta rtc-server listen-port Syntax rta source-ip ip-address Undo rta source-ip Rta server enableSyntax rta server enable Undo rta server enable Rta source-ip TCP connections Rta templateRta terminal Hiding 917 Sendbuf bufsizeSyntax sendbuf bufsize size Undo sendbuf bufsize Syntax sendbuf threshold value Undo sendbuf threshold Sendbuf thresholdTcp Undo testkey # Disable TCP delayTestkey # Set the TCP send buffer size to 512 bytes Values are used for the hotkeys of flow control Update changed-configAccess Update changed-config 921 Vty descriptionVty hotkey Undo vty vty-numberdescription Vty password 923 Vty rtc-client remoteVty rtc-server remote Undo vty vty-numberscreencode Related command menu screencodeVty screencode 925 Vty telnet remoteVty tty remote Example # Set the screen code for VTY 1 to E!9Q Syntax vty-switch threshold times Vty-switch priorityVty-switch threshold Syntax vty-switch priority Undo vty-switch priority 927 Undo vty-switch threshold Terminal Access Configuration Commands Syntax bandwidth-based-sharing Undo bandwidth-based-sharing IP Routing Table CommandsBandwidth-based-sharing Display ip routing-table String, the end of a string Special characters for regular expressions 931 Syntax display ip routing-table acl acl-number verbose Display ip routing-table acl 933 IP Routing Table Commands 935 Display ip routing-table ip-address Display ip routing-table ip-address mask longer-match Display ip routing-table ip-addressDisplay ip routing-table ip-address mask Display ip routing-table ip-addresslonger-match 937 Display ip routing-table ip-prefix 939 Display ip routing-table protocolFor detailed description of the above output, see Table View Any view Display ip routing-table statistics# Display summary information about static routes # Display recursive route information Display ip relay-routeDisplay ip relay-tunnel Display ip relay-route vpn-instance vpn-instance-name Syntax display ipv6 routing-table Display load-sharing ip addressDisplay ipv6 routing-table Examples # Display recursive tunnel information 943 Display ipv6 routing-table aclSyntax display ipv6 routing-table acl acl6-number verbose Display ipv6 routing-table ipv6-addressprefix-length Display ipv6 routing-table ipv6-addressRefer to for description about the above output 945 Display ipv6 routing-table ipv6-address1 ipv6-address2 Display ipv6 routing-table protocol Display ipv6 routing-table ipv6-prefix 947 Display ipv6 routing-table statisticsSyntax display ipv6 routing-table statistics # Display routing statistics Entire routing table and information for each route Display ipv6 routing-table verboseDisplay ipv6 relay-route Display ipv6 routing-table verbose 949 Display ipv6 relay-tunnelDisplay ipv6 relay-tunnel # Display IPv6 recursive tunnel information Syntax load-bandwidth bandwidth Undo load-bandwidth Reset load-sharingLoad-bandwidth Ripng , or static Reset ip routing-table statistics protocolReset ipv6 routing-table statistics Reset ipv6 routing-table statistics protocol all protocol Sysname reset ipv6 routing-table statistics protocol all Functions of the keywords BGP Configuration CommandsConfiguration Commands on Aggregate Suppress-policy If-match clause of the route-policy commandBalance BGP/BGP-VPN instance view Syntax balance number Undo balance 955 Related commands display bgp routing-tableBestroute as-path-neglect BGP/BGP-VPN instance view View BGP view/BGP-VPN instance view Syntax bestroute compare-med Undo bestroute compare-med Comparison is not enabled by defaultBestroute compare-med BGP/BGP-VPN instance view Bestroute med-confederation BGP/BGP-VPN instance view 957 BgpCompare-different-as-med BGP/BGP-VPN instance view Syntax confederation id as-number Undo confederation id Confederation id View BGP view Related commands confederation id and confederation peer-asConfederation nonstandard Confederation peer-as Undo dampening Dampening BGP/BGP-VPN instance viewUndo confederation peer-as as-number-list Examples # Specify confederation peer sub ASs 2000 961 Default ipv4-unicastExamples # In BGP view, configure BGP route dampening Syntax default ipv4-unicast Undo default ipv4-unicast Syntax default med med-value Undo default med Default local-preference BGP/BGP-VPN instance viewDefault med BGP/BGP-VPN instance view 963 Default-route imported BGP/BGP-VPN instance viewSyntax default-route imported Undo default-route imported Syntax display bgp group group-name Related commands import-routeBGP/BGP-VPN instance viewDescription on the fields of the display bgp group command Display bgp group # Display routing information that has been advertised Advertised with the network commandDisplay bgp network Display bgp network MED Description on the fields of the display bgp paths commandDisplay bgp paths Display bgp peer 967 Description on the fields of the display bgp peer command Display bgp routing-table Description on the fields of the display bgp routing command 969 Display bgp routing-table as-path-acl Display bgp routing-table cidr Display bgp routing-table cidr 971 Display bgp routing-table communityDisplay bgp routing-table community-list # Display dampened BGP routes Display bgp routing-table dampenedDisplay bgp routing-table dampened Dampened BGP routes Display bgp routing-table dampening parameter Related commands dampening BGP/BGP-VPN instance viewDisplay bgp routing-table dampening parameter Display bgp routing-table different-origin-as Longer-match Display bgp routing-table flap-info 975 Related commands display bgp peerDisplay bgp routing-table peer Display bgp routing-table statistic Display bgp routing-table regular-expressionDisplay bgp routing-table statistic Ebgp-interface-sensitive 977 Filter-policy export BGP/BGP-VPN instance viewUndo ebgp-interface-sensitive Filter-policy import BGP/BGP-VPN instance view 979 Graceful-restart timer restartGraceful-restart BGP view Syntax graceful-restart Undo graceful-restart Using this command can speed up route convergence Graceful-restart timer wait-for-ribGraceful-restart timer wait-for-rib timer Undo graceful-restart timer wait-for-rib 981 Import-route BGP/BGP-VPN instance view Syntax log-peer-change Undo log-peer-change Log-peer-change 983 Network BGP/BGP-VPN instance view Peer advertise-ext-community BGP/BGP-VPN instance view Peer advertise-community BGP/BGP-VPN instance view 985 Related commands display bgp routing-table peerPeer allow-as-loop BGP/BGP-VPN instance view Undo peer ip-address Peer as-number BGP/BGP-VPN instance viewPeer as-path-acl BGP/BGP-VPN instance view 987 Peer capability-advertise conventional Peer capability-advertise route-refresh Undo peer group-name ip-address connect-interface Peer default-route-advertise BGP/BGP-VPN instance viewUndo peer group-nameip-address default-route-advertise Peer connect-interface BGP/BGP-VPN instance view Peer description BGP/BGP-VPN instance view 991 Peer ebgp-max-hop BGP/BGP-VPN instance view Peer fake-as BGP/BGP-VPN instance view Peer enable BGP viewSyntax peer ip-addressenable Undo peer ip-addressenable 993 Related commands peer as-path-aclBGP/BGP-VPN instance viewPeer filter-policy BGP/BGP-VPN instance view Peer group BGP/BGP-VPN instance view 995 Peer ignore BGP/BGP-VPN instance viewPeer ip-prefix Peer keep-all-routes BGP/BGP-VPN instance view View BGP view /BGP-VPN instance view Peer log-change BGP/BGP-VPN instance viewPeer next-hop-local BGP/BGP-VPN instance view Undo peer group-name ip-address next-hop-local Peer password 999 # Perform the similar configuration on the peerPeer preferred-value BGP/BGP-VPN instance view Undo peer group-name ip-address preferred-value Undo peer group-name ip-address public-as-only Peer public-as-only BGP/BGP-VPN instance view 1001 Peer reflect-client BGP/BGP-VPN instance view Peer route-policy BGP/BGP-VPN instance view Peer route-limit BGP/BGP-VPN instance view 1003 Peer route-update-interval BGP/BGP-VPN instance view Undo peer group-nameip-address substitute-as Peer substitute-as BGP/BGP-VPN instance view 1005 Peer timer BGP/BGP-VPN instance viewRelated commands timer BGP/BGP-VPN instance view Syntax reflect between-clients Undo reflect between-clients Preference BGP/BGP-VPN instance viewReflect between-clients BGP view Undo preference 1007 Examples # Disable route reflection between clientsReflector cluster-id BGP view Examples # Set the cluster ID to Refresh bgp Reset bgpAll Resets all BGP connections As-number Resets BGP connections to peers in the AS 1009 Reset bgp dampeningReset bgp flap-info Syntax router-id router-id Undo router-id Reset bgp ipv4 allSyntax reset bgp ipv4 all Router-id 1011 Summary automaticSyntax summary automatic Undo summary automatic Syntax synchronization Undo synchronization Timer BGP/BGP-VPN instance viewSyntax timer keepalive keepalive hold holdtime Undo timer Synchronization BGP view 1013 Related commands peer timer BGP/BGP-VPN instance view BGP Configuration Commands Debugging bgp all BGP Debugging Commands BGP received an Open message from the peer BGP configuration information 1017 Debugging bgp detailSyntax debugging bgp detail Undo debugging bgp detail Route was deleted from the instance Debugging bgp event 1019 BGP has received an Update messageDebugging bgp graceful-restart State has changed from Opensent to Openconfirm BGP GR Helper received an EOR message from peer BGP neighbor 10.1.1.1 is performing GRBGP peer relationship has been successfully established 1021 Description on the fields of the debugging bgp commandDebugging bgp WTR Description on the fields of the debugging bgp open commandInformation about the sent BGP Open message AFI/ Safi 1023 Information about the received BGP Open messageInformation about the sent BGP Keepalive message Information about the received BGP Keepalive message ConnectRetry timer for BGP peer 2.2.2.2 expired Debugging bgp timer Update messages Hold timer expired on BGP peerReceive Enables the debugging for received BGP packets Send Enables the debugging for sent BGP packets Ip-prefix ip-prefix-name receive send verbose Debugging bgp update ipv4Ip-prefix-name receive send verbose 1027 Debugging bgp update ipv6Update messages of IPv4 address family Complete By default, this debugging is disabled Receive Enables/disables debugging for received BGP packetsSend Enables/disables debugging for sent BGP packets For IPv6 BGP update messages Send verbose Debugging bgp update l2vpnUpdate messages of IPv6 address family Verbose Receive send verbose Debugging bgp update label-routeUpdate messages in an L2VPN environment Acl-number ip-prefix ip-prefix-name receive send verbose 1031 Update message information of L3VPN labeled routes Update message information of IPv6 labeled routes Debugging bgp update peer 1033 Debugging bgp update vplsVpls Update messages For BGP Vpls Update messages Information about the received Vpls update message Debugging bgp update vpn-instanceInformation about the sent Vpls update message Examples None Debugging bgp update vpnv4BGP VPNv4 Update messages For BGP VPNv4 Update messages Update message information of VPNv4 Undo area-authentication-mode IS-IS Configuration CommandsArea-authentication-mode Area-authentication-mode simple md5 password ip osi Bandwidth-reference IS-IS view Auto cost enableSyntax auto-cost enable Undo auto-cost enable Related commands bandwidth-referenceIS-IS view, cost-style 1039 Related commands auto cost enableCircuit-cost Undo cost-style Related commands isis cost, cost-styleCost-style Relax-spf-limit 1041 Default-route-advertise IS-IS viewRelated commands isis cost Display isis brief Description on the fields of the display isis brief command Display isis graceful-restart status Display isis debug-switches Tunnel Displays IS-IS tunnel information Display isis interfaceTraffic-eng Displays IS-IS traffic engineering information Verbose Displays IS-IS interface detail information DIS Examples # Display IS-IS enabled interface information# Display detailed IS-IS interface information 1045 BFD Display isis licenseSyntax display isis license License information varies with device models Display isis lsdb ATT/P/OL Display isis mesh-groupLspid Display isis peer # Display the configuration information of IS-IS mesh-group# Configure a static mapping for the remote IS-IS system Display isis name-table PRI Display isis routeUp state and direct interface’s IP address # Display detailed IS-IS neighbor information 1051 Description on the fields of the display isis route command# Display IS-IS IPv4 routing information Display isis spf-log Display isis statistics IS-IS view Domain-authentication-modeSimple Specifies to send the password in plain text Md5 Specifies to send the password encrypted with MD5 1055 Filter-policy export IS-IS view Filter-policy import IS-IS view Related commands filter-policy import IS-IS view Undo flash-flood level-1 level-2 Related commands filter-policy export IS-IS viewFlash-flood Level-1 level-2 Graceful-restart Graceful-restart IS-IS viewGraceful-restart interval IS-IS view Undo graceful-restart suppress-sa Graceful-restart suppress-saImport-route IS-IS view Graceful-restart suppress-sa Related commands import-route isis level-2 into level-1 Undo import-route isis level-2 into level-1 Related commands import-routeIS-IS viewImport-route isis level-2 into level-1 Examples # Redistribute static routes and set the cost to Isis Isis authentication-mode 1063 This command is not available in loopback interface viewIsis circuit-level level-1 level-1-2 level-2 Undo isis circuit-level Syntax isis circuit-type p2p Undo isis circuit-type Related commands is-levelIsis circuit-type 1065 Syntax isis dis-name symbolic-name Undo isis dis-nameIsis cost Isis dis-name Isis dis-priority Examples # Configure the name as Localarea for the local LAN Isis mesh-group Isis enableSyntax isis enable process-id Undo isis enable Related commands isis, network-entity Syntax isis peer-ip-ignore Undo isis peer-ip-ignore Isis peer-ip-ignore 1069 Isis small-helloSyntax isis silent Undo isis silent Syntax isis small-hello Undo isis small-hello Isis timer hello Isis timer csnp Undo isis timer holding-multiplier level-1 level-2 Isis timer holding-multiplierIsis timer holding-multiplier value level-1 level-2 Related commands isis timer retransmit Isis timer lspRelated commands isis timer hello Syntax isis timer lsp time count count Undo isis timer lsp Syntax is-level level-1 level-1-2 level-2 Undo is-level Isis timer retransmitRelated commands Examples Isis timer lsp Is-level Syntax is-name sys-name Undo is-name Related commands isis circuit-levelExamples # Configure the router to work in Level-1 Is-name Undo is-name map sys-id Is-snmp-traps enableSyntax is-snmp-traps enable Undo is-snmp-traps Is-name map Lsp-fragments-extend Log-peer-change IS-IS view 1077 Lsp-length originate Syntax lsp-length receive size Undo lsp-length receive # Restore the defaultLsp-length receive Maximum load-balancing IS-IS view Network-entity net Related commands Isis, isis enable ExamplesNetwork-entity Preference IS-IS view Examples # Clear all IS-IS data structure information Reset isis all Undo set-overload Reset isis peerSet-overload Allow interlevel external Syntax spf-slice-size duration-time Undo spf-slice-size Spf-slice-size 1083 Summary IS-IS view Interval Timer isp-generationUndo timer lsp-generation level-1 level-2 Generation interval Related commands timer lsp-refresh Timer lsp-max-ageTimer lsp-refresh Syntax timer lsp-max-age seconds Undo timer lsp-max-age Examples # Set the LSP refresh interval to 1500 seconds Timer spfRelated commands timer lsp-max-age Undo timer spf 1087 Virtual-system# Set the maximum SPF calculation interval to 15 seconds Undo virtual-system virtual-system-id IS-IS Configuration Commands Ha-events interface-information memory-allocating IS-IS Debugging CommandsEvent Enables IS-IS event debugging Debugging isis IS-IS Debugging Commands Snpa Snpa 1091 Field 1093 CircuitName not enabled SNP packet length mismatch Length length 1095 Updt Reset Required Sending pduLevel pduType on circuitName 1097 Sending pduLevel Csnp PDU fails 1099 Tent New Distance from RootNodeSourceId LSP 1101 LevelType LSP level, which can be L1 or L2 1103 Router B sent Csnp packets IP address took effect on the IS-IS interface 1105 IS-IS Debugging Commands Abr-summary Ospf area view Ospf Configuration CommandsRelated commands L3VPN Configuration Commands on Undo area area-id Area Ospf viewAsbr-summary Syntax area area-id View Ospf area view Authentication-modeSimple Specifies the simple authentication mode Display ospf asbr-summary Bandwidth-reference Ospf view DefaultRelated commands ospf authentication-mode Syntax default cost cost limit limit tag tag type type Syntax default-cost cost Undo default-cost Default-cost Ospf area viewUndo default cost limit tag type Related commands import-route Ospf view Undo default-route-advertise Default-route-advertise Ospf viewRelated commands stub Ospf area view, nssa Default-route-advertise summary cost cost # Describe the Ospf area0 as bone area Description OSPF/OSPF area viewDisplay ospf abr-asbr Syntax description description Undo description Display ospf asbr-summary Examples # Display Ospf brief information Related commands asbr-summaryDisplay ospf brief Syntax display ospf process-id brief Mpls TE Description on the fields of the display ospf brief command 1117 Display ospf cumulativeSyntax display ospf process-id cumulative ASE/NSSA Display ospf errorSyntax display ospf process-id error Nssa 1119 Description on the fields of the display ospf error command Display ospf interface BDR Display ospf lsdb1121 # Display Type2 LSA Network LSA information in the Lsdb Description on the fields of the display ospf lsdb command LS ID Display ospf nexthopSyntax display ospf process-id nexthop 1123 Display ospf peer Syntax display ospf process-id peer statistics Description on the fields of the display ospf peer commandDisplay ospf peer statistics # Display brief Ospf neighbor information Keep neighbor relationship Init Display ospf request-queue 1127 Display ospf retrans-queueExamples # Display Ospf request list information Display ospf routing 1129 Description on the fields of the display ospf vlink commandDisplay ospf vlink Syntax display ospf process-id vlink State Enables state logging Enable link-local-signalingEnable log Error Enables error logging 1131 Enable out-of-band-resynchronizationFilter import/export Undo filter-policy export protocol process-id By default, Summary LSAs filtering is disabledThis command is only available on an ABR Filter-policy export Ospf view 1133 Examples # Filter redistributed routes using ACLFilter-policy import Ospf view Graceful-restart Ospf view Syntax graceful-restart help acl-numberprefix prefix-list Examples # Enable Ietf Graceful Restart for Ospf process# Enable non-IETF Graceful Restart for Ospf process Graceful-restart help 1135 Related commands ospf timer deadGraceful-restart interval Ospf view Host-advertise Import-route Ospf view 1137 Related commands ExamplesDefault-route-advertise Ospf view Import-route command cannot redistribute default routes Lsa-arrival-interval Related commands lsa-generation-interval Undo lsa-generation-interval Related commands lsa-arrival-intervalLsa-generation-interval Lsdb-overflow-limit Number Maximum route number in the range 1 to Maximum load-balancing Ospf viewMaximum-routes 1141 Related commands ospfNetwork Ospf area view Nssa Syntax opaque-capability enable Undo opaque-capability Opaque-capability enableRelated commands default-cost Ospf area view Examples # Configure area1 as an Nssa area 1143 Ospf authentication-modeOspf Undo ospf process-id Related commands authentication-mode 1145 Ospf costSyntax ospf cost value Undo ospf cost Syntax ospf mib-binding process-id Undo ospf mib-binding Ospf dr-priorityOspf mib-binding Syntax ospf dr-priority priority Undo ospf dr-priority Ospf network-type Ospf mtu-enable Syntax ospf timer dead seconds Undo ospf timer dead Ospf timer deadRelated commands ospf dr-priority This command is not supported on the Null interface 1149 Ospf timer helloRelated commands ospf timer hello Syntax ospf timer hello seconds Undo ospf timer hello Syntax ospf timer poll seconds Undo ospf timer poll Ospf timer pollOspf timer retransmit 1151 Ospf trans-delaySyntax ospf trans-delay seconds Undo ospf trans-delay Peer Preference ase route-policy route-policy-name value Command sets priority for internal routesPreference Examples # Specify the neighbor IP address 1153 Reset ospf countersReset ospf process Syntax reset ospf process-id process Syntax rfc1583 compatible Undo rfc1583 compatible Reset ospf redistributionSyntax reset ospf process-id redistribution Rfc1583 compatible Silent-interface Ospf view Snmp-agent trap enable ospf Ospf Configuration Commands Syntax stub no-summary Undo stub Spf-schedule-intervalStub Ospf area view Undo spf-schedule-interval Undo stub-router Default-cost Ospf area viewStub-router Stub-router 1159 Examples # Enable a stub-routerVlink-peer Ospf area view Related commands authentication-mode,display ospf peer Checkzero RIP Configuration CommandsDefault cost RIP view Syntax default cost value Undo default cost Display rip Default-route originateRelated commands import-route RIP view # Disable default route sending 1163 Description on the fields of the display rip command X.X/X Description on fields of the display rip database commandDisplay rip database Syntax display rip process-iddatabase 1165 Display rip interfaceDisplay rip route RIP Configuration Commands 1167 Description on the fields of the display rip route commandFilter-policy export RIP view # Display the routing statistics of RIP process Examples # Reference ACL 2000 to filter outbound routes Filter-policy import RIP viewInterface-type interface-number Specifies an interface 1169 Host-routeSyntax host-route Undo host-route Including bgp , direct , isis , ospf , rip , rip and static Default cost RIP viewImport-route RIP view 1171 # Set the default cost for redistributed routes toMaximum load-balancing RIP view Syntax peer ip-address 1173 Reset rip statisticsSyntax reset rip process-idstatistics Rip Undo rip authentication-mode Rip authentication-mode Format defined in RFC Mode and parametersBy default, an interface is enabled to receive RIP messages # Enable Ethernet1/0 to receive RIP messages Rip metricout Related commands rip metricoutRelated commands rip metricin Rip metricin Syntax rip output Undo rip output Rip mib-bindingRip output Syntax rip mib-binding process-id Undo rip mib-binding Rip split-horizon Related commands rip inputRip poison-reverse Rip triggered Examples # Enable the split horizon function on Ethernet1/0Related commands summary Rip summary-address Undo rip version Rip versionUndo rip triggered Rip version 1 2 broadcast multicast 1181 Silent-interface RIP viewAll Silents all interfaces Messages Syntax summary TimersRelated commands rip version Summary 1183 Trip retransmit count Undo trip retransmit timer Trip retransmit timerTrip retransmit timer retransmit-time-value Version 1 Validate-source-addressVersion Syntax validate-source-address Undo validate-source-address Sysname system-view Sysname rip Sysname-rip-100 version Syntax apply comm-list comm-list-numberdelete Routing Policy Common Configuration CommandsApply as-path Apply comm-list delete Undo apply comm-list Apply community Parameters + Increases cost value. + Decreases cost value Apply costSyntax apply cost + value Undo apply cost View Routing policy view Apply extcommunity Apply cost-type 1191 No level is set by defaultApply isis Apply isis level-1 level-1-2 level-2 Undo apply isis Syntax apply mpls-label Undo apply mpls-label Related commands route-policyApply local-preference Apply mpls-label 1193 Apply originApply preference Syntax apply preference preference Undo apply preference Syntax apply tag value Undo apply tag Apply preferred-valueApply tag 1195 Display ip as-pathSyntax display ip as-path as-path-acl number Examples # Display the information of BGP AS path ACL Syntax display ip extcommunity-list ext-comm-list-number Display ip community-listDisplay ip extcommunity-list Examples # Display the information of routing policy Display route-policyIf-match as-path Syntax display route-policy route-policy-name If-match community Related commands route-policy,ip as-pathaclRelated commands route-policyand ip community-list 1199 If-match costIf-match extcommunity Syntax if-match cost value Undo if-match cost If-match interface If-match route-type If-match mpls-label Undo ip as-path as-path-number If-match tagIp as-path Syntax if-match tag value Undo if-match tag 1203 Ip community-list Sysname system-view Sysname ip community-list 100 permit 1205 Ip extcommunity-listRoute-policy Undo ip extcommunity-list ext-comm-list-number Routing Policy Common Configuration Commands Syntax display ip ip-prefix ip-prefix-name IPV4 Routing Policy Configuration CommandsDisplay ip ip-prefix Examples # Display the statistics of IPv4 prefix list abc Related commands ip ip-prefix If-match ip-prefix Related commands Route-policy ExamplesIf-match ip Ip ip-prefix 1211 Reset ip ip-prefixSyntax reset ip ip-prefix ip-prefix-name IPV4 Routing Policy Configuration Commands Syntax display ip ipv6-prefix ipv6-prefix-name IPV6 Routing Policy Configuration CommandsApply ipv6 next-hop Display ip ipv6-prefix Address based match criterion for IPv6 routes If-match ipv6Next-hop Matches the next hop of IPv6 routing information String of 1 to 19 characters 1215 Ip ipv6-prefix Examples # Clear the statistics of IPv6 prefix list abc Reset ip ipv6-prefixSyntax reset ip ipv6-prefix ipv6-prefix-name Examples # Delete all static routes on the router Static Routing Configuration CommandsDelete static-routes all Ip route-static Configured gateway-address 1219 Must be identical to that configured in the NQA test groupEthernet interface and Vlan interface Associate it with a Track entry Examples # Set the default preference of static routes to Ip route-static default-preference Bestroute as-path-neglect IPv6 address family view IPV6 BGP Configuration CommandsRelated commands display ipv6 routing-tableon Balance IPv6 address family view Bestroute med-confederation IPv6 address family view Bestroute compare-med IPv6 address family view 1223 Compare-different-as-med IPv6 address family view Dampening IPv6 address family view 1225 Default local-preferenceIPv6 address family viewDefault med IPv6 address family view Syntax display bgp ipv6 group ipv6-group-name Default-route imported IPv6 address family viewDisplay bgp ipv6 group 1227 Display bgp ipv6 networkSyntax display bgp ipv6 network Syntax display bgp ipv6 paths as-regular-expression Display bgp ipv6 paths Incomplete Display bgp ipv6 peer1229 Field Description Local router ID Display bgp ipv6 routing-table 1231 Display bgp ipv6 routing-table as-path-acl Examples # Display routes filtered through the AS path ACL Display bgp ipv6 routing-table community Examples # Display IPv6 BGP dampened routes Display bgp ipv6 routing-table community-listDisplay bgp ipv6 routing-table dampened Syntax display bgp ipv6 routing-table dampened Syntax display bgp ipv6 routing-table different-origin-as Display bgp ipv6 routing-table dampening parameterDisplay bgp ipv6 routing-table different-origin-as Syntax display bgp ipv6 routing-table dampening parameter 1235 Display bgp ipv6 routing-table flap-infoExamples # Display IPv6 BGP routes from different ASs Examples # Display IPv6 BGP route flap statistics Examples # Display IPv6 BGP label routing information CommandDisplay bgp ipv6 routing-table label Syntax display bgp ipv6 routing-table label 1237 Display bgp ipv6 routing-table peerDisplay bgp ipv6 routing-table regular-expression Syntax display bgp ipv6 routing-table statistic Display bgp ipv6 routing-table statisticFilter-policy exportIPv6 address family view Parameters as-regular-expression AS regular expression 1239 Filter-policy import IPv6 address family view Syntax group ipv6-group-name internal external Group IPv6 address family viewImport-route IPv6 address family view Examples # Reference ACL6 2001 to filter all inbound routes 1241 Ipv6-familyNetwork IPv6 address family view Syntax ipv6-family Undo ipv6-family Peer advertise-community IPv6 address family view 1243 Peer advertise-ext-community IPv6 address family viewPeer allow-as-loop IPv6 address family view Peer as-number IPv6 address family view 1245 Peer as-path-acl IPv6 address family viewImport export Peer connect-interface IPv6 address family view 1247 Peer default-route-advertisePeer description IPv6 address family view Peer ebgp-max-hop IPv6 address family view 1249 Peer enable IPv6 address family viewPeer fake-as IPv6 address family view Peer filter-policy IPv6 address family view 1251 Peer group IPv6 address family viewPeer ignore IPv6 address family view Peer ipv6-prefix 1253 Peer keep-all-routes IPv6 address family viewPeer label-route-capability IPv6 address family view Peer next-hop-local IPv6 address family view Peer log-change IPv6 address family view 1255 Peer preferred-value IPv6 address family view Peer reflect-client IPv6 address family view Peer public-as-only IPv6 address family view 1257 Peer route-limit IPv6 address family view Peer route-policy IPv6 address family view Peer route-update-interval IPv6 address family view 1259 Undo peer ipv6-group-nameipv6-address route-update-intervalPeer substitute-as IPv6 address family view Preference IPv6 address family view Peer timer IPv6 address family viewRelated commands timer IPv6 address family view 1261 Reflect between-clients IPv6 address family view Refresh bgp ipv6 Examples # Enable route reflection between clientsReflector cluster-id IPv6 address family view 1263 Reset bgp ipv6 Reset bgp ipv6 flap-info Reset bgp ipv6 dampening 1265 Synchronization IPv6 address family view Timer IPv6 address family view 1267 Related commands peer timer IPv6 address family view IPV6 BGP Configuration Commands IPV6 IS-IS Configuration Commands # Display detailed IPv6 IS-IS routing information 1271 Ipv6 default-route-advertise Undo ipv6 filter-policy export protocol process-id Ipv6 enableSyntax ipv6 enable Undo ipv6 enable Ipv6 filter-policy export 1273 Related commands ipv6 filter-policy importIpv6 filter-policy import Undo ipv6 filter-policy import Ipv6 import-route Related commands ipv6 filter-policy export 1275 Ipv6 import-route isisv6 level-2 into level-1Undo ipv6 import-route isisv6 level-2 into level-1 Ipv6 preference Ipv6 maximum load-balancing 1277 Ipv6 summary Syntax isis ipv6 enable process-id Undo isis ipv6 enable Isis ipv6 enableExamples # Configure a summary route of 2002/32 Area OSPFv3 view IPV6 OSPFV3 Configuration CommandsAbr-summary OSPFv3 area view Examples # Enter OSPFv3 Area 0 view Default costDefault-cost OSPFv3 area view Syntax default-cost value Debugging state information Related commands stubOSPFv3 area viewDisplay debugging ospfv3 Display debugging ospfv3 Syntax display ospfv3 process-id Description on the fields of the display isofv3 commandDisplay ospfv3 1283 Display ospfv3 interface Display ospfv3 lsdb 1285 # Display Link-local LSA information in the Lsdb Syntax display ospfv3 lsdb statistic Display ospfv3 lsdb statistic Interface-type interface-number interface type and number Display ospfv3 next-hopDisplay ospfv3 peer Syntax display ospfv3 process-id next-hop Description on the fields of the display isofv3 peer command Syntax display ospfv3 process-id request-list statistics Display ospfv3 peer statisticDisplay ospfv3 request-list Syntax display ospfv3 peer statistic LS-ID Display ospfv3 retrans-list# Display the statistics of OSPFv3 link state request list Syntax display ospfv3 process-id retrans-list statistics 1291 Display ospfv3 routing # Display the statistics of OSPFv3 routing table Syntax display ospfv3 process-id topology area area-id Display ospfv3 statisticDisplay ospfv3 topology Syntax display ospfv3 statistic Syntax display ospfv3 process-id vlink Display ospfv3 vlink 1295 Filter-policy exportOSPFv3 view Routes that fail to pass are not added to the routing table Filter-policy importOSPFv3 view Both Ebgp and Ibgp routes Import-routeOSPFv3 viewAllow-ibgp direct static cost value type type route-policy Direct static Process Maximum load-balancingOSPFv3 view Undo ospfv3 process-id Related commands router-idOspfv3 Ospfv3 area Ospfv3 dr-priority Ospfv3 cost 1301 Ospfv3 timer deadOspfv3 mtu-ignore Related commands ospfv3 timer hello Ospfv3 timer hello 1303 Ospfv3 timer retransmitOspfv3 trans-delay Related commands ospfv3 timer dead Preference ase route-policy route-policy-name preference OSPFv3 processes on a router Related commands Ospfv3Silent-interfaceOSPFv3 view Router-id router-id Undo spf timers Spf timers StubOSPFv3 area view Related commands default costExamples # Configure OSPFv3 area 1 as a stub area Undo vlink-peer router-id hello retransmit trans-delay dead IPV6 OSPFV3 Configuration Commands View RIPng view IPV6 Ripng Configuration CommandsDefault cost RIPng view Syntax default cost cost Undo default cost Syntax display ripng process-id Related commands import-routeDisplay ripng Syntax display ripng process-iddatabase Description on the fields of the display ripng commandDescription on fields of the display ripng database command Display ripng database Display ripng interface 1313 Display ripng routeSyntax display ripng process-idroute Filter-policy import RIPng view Filter-policy export 1315 Import-route Maximum load-balancing RIPng view Related commands default cost on Undo ripng process-id # Restore the default RIPng route priority# Disable RIPng process Ripng Syntax ripng process-idenable Undo ripng enable Ripng default-routeRipng enable Syntax ripng metricin value Undo ripng metricin Related commands ripng metricoutRipng metricin Ripng metricout Syntax ripng poison-reverse Undo ripng poison-reverse Related commands ripng metricinRipng poison-reverse Ripng split-horizon Poison reverse function takes effect Information, refer to Frame Relay Configuration Commands onLapb and X.25 Configuration Commands on Ripng summary-address Timers 1323 IPV6 Ripng Configuration Commands Delete ipv6 static-routes all IPV6 Static Routing Configuration CommandsDelete ipv6 static-routes all Ipv6 route-static Sysname system-view Sysname ipv6 route-static 112 24 Display multicast boundary Multicast Routing Forwarding Configuration CommandsRelated command multicast boundary Display multicast forwarding-table Value Meaning Major values of the flags field1329 MID Display multicast minimum-ttl Related command multicast minimum-ttl 1331 Related command display multicast forwarding-tableDisplay multicast routing-table Description on the fields of display multicast routing-table Display multicast routing-table static 1333 Display multicast rpf-info Ip rpf-route-static 1335 Mtracert Related command display multicast routing-table static 1337 Description on the fields of the mtracert commandMulticast boundary Multicast forwarding-table downstream-limit Related command display multicast boundary 1339 Multicast forwarding-table route-limit View System view, VPN instance view Multicast load-splittingMulticast longest-match Syntax multicast longest-match Undo multicast longest-match 1341 Multicast routing-enableRelated command display multicast minimum-ttl Multicast minimum-ttl # Enable IP multicast routing in VPN instance mvpn Reset multicast forwarding-table 1343 Reset multicast routing-table Sysname reset multicast routing-table Display igmp group Igmp Configuration Commands Display igmp interface Description on the fields of the display igmp group command 1347 Display igmp routing-table Syntax fast-leave group-policy acl-number Undo fast-leave Related command igmp fast-leave,last-member-query-intervalFast-leave Igmp view Igmp Related command igmp Igmp enableRelated command igmp enable, and multicast routing-enableon Syntax igmp enable Undo igmp enable 1351 Igmp fast-leaveIgmp group-policy Undo igmp group-policy Igmp max-response-time By default, the last-member query interval is 1 secondIgmp last-member-query-interval 1353 Igmp require-router-alert Igmp interface Robust-count Igmp view , igmp timer query , igmpIgmp robust-count Igmp send-router-alert Igmp static-group Igmp timer query Igmp timer other-querier-present Undo igmp version Related command version Igmp viewIgmp version Last-member-query-interval Syntax require-router-alert Max-response-time Igmp viewRequire-router-alert Igmp view 1359 Reset igmp groupUndo require-router-alert View Public instance Igmp view, VPN instance Igmp view Syntax robust-count robust-value Undo robust-count Related command display igmp groupRobust-count Igmp view 1361 Timer other-querier-present Igmp viewSend-router-alert Igmp view Syntax send-router-alert Undo send-router-alert Public instance Timer query Igmp viewSyntax timer query interval Undo timer query 1363 Related command igmp versionVersion Igmp view Igmp Configuration Commands Characters Msdp Configuration CommandsCache-sa-enable Display msdp brief Display msdp peer-status 1367 Display msdp sa-cache 1369 Related command cache-sa-enable Display msdp sa-count View Public instance Msdp view, VPN instance Msdp view Encap-data-enableSyntax encap-data-enable Undo encap-data-enable Import-source Msdp Related command peer sa-policyRelated command display multicast routing-tableon 1373 Originating-rpPeer connect-interface Undo originating-rp Peer mesh-group Related command static-rpf-peerRelated command display msdp peer-status Peer description 1375 Peer minimum-ttlUndo peer peer-addressmesh-group Undo peer peer-addressminimum-ttl Peer sa-cache-maximum Peer request-sa-enable Display msdp peer-status and import-source Import-source commandPeer sa-policy From the Msdp peer Peer sa-request-policy Reset msdp peer 1379 Reset msdp sa-cacheRelated command cache-sa-enableand display msdp sa-cache Undo shutdown peer-address Reset msdp statisticsShutdown Msdp View Undo static-rpf-peer peer-address Related command display msdp peer-statusand ip prefix-listExample # Configure static RPF peers in the public instance Static-rpf-peer Syntax timer retry interval Undo timer retry Timer retry Bsr-policy PIM view PIM Configuration CommandsAuto-rp enable Related command static-rp PIM view Undo c-bsr Bsr PIM view 1385 Bsr admin-scopeSyntax c-bsr admin-scope Undo c-bsr admin-scope Bsr global Undo c-bsr group group-address Bsr group Syntax c-bsr holdtime interval Undo c-bsr holdtime Bsr hash-length PIM viewBsr holdtime PIM view Syntax c-bsr hash-length hash-length Undo c-bsr hash-length Bsr PIM view and c-bsr holdtime PIM view Related command c-bsr PIM view and c-bsr interval PIM viewBsr interval PIM view Bsr priority PIM view 1389 Rp PIM view Undo c-rp advertisement-interval Related command c-bsr PIM viewRp advertisement-interval PIM view Rp advertisement-interval interval Syntax c-rp holdtime interval Undo c-rp holdtime Related command c-rp PIM view and c-bsr interval PIM viewRp holdtime PIM view Crp-policy PIM view Display pim bsr-info Related command c-bsr PIM view and c-rp PIM view 1393 Display pim claimed-route Display pim control-message counters BSR 1395 Display pim interface Description on the fields of the display pim grafts commandDisplay pim grafts 1397 PIM DR Display pim join-prune 1399 Display pim neighbor Interface connecting the PIM neighbor 1401 Display pim routing-table Sysname display pim routing-table Vpn-instance public net 1403 Display pim rp-info Description on the fields of the display pim rp-info command 1405 Related command pim hello-optiondr-priorityHello-option dr-priority PIM view Hello-option holdtime PIM view Hello-option neighbor-tracking PIM view Hello-option lan-delay PIM viewThis command is effective for both PIM-DM and PIM-SM Related command pim hello-option holdtime 1407 Related command pim hello-optionneighbor-trackingHello-option override-interval PIM view Syntax holdtime assert interval Undo holdtime assert Holdtime assert PIM viewHoldtime join-prune PIM view Syntax jp-pkt-size packet-size Undo jp-pkt-size Related command jp-queue-size PIM viewJp-pkt-size PIM view Jp-queue-size PIM view Undo pim vpn-instance vpn-instance-name Related command multicast routing-enableonPim Bsr PIM view , and multicast boundary on Pim bsr-boundaryPim dm Pim hello-option dr-priority Related command pim sm, ssm-policy PIM viewExample # Enable PIM-DM on Ethernet 1/0 Related command hello-optiondr-priority PIM view 1413 Pim hello-option lan-delayRelated command hello-option holdtime PIM view Pim hello-option holdtime Pim hello-option override-interval Pim hello-option neighbor-tracking 1415 Pim holdtime assertPim holdtime join-prune View Interface view Parameter None Pim require-genidPim sm Example # Disable state refresh on Ethernet 1/0 Pim timer graft-retryRelated command pim dm Example # Enable PIM-SM on Ethernet 1/0 Related command timer hello PIM view Pim timer helloPim timer join-prune Syntax pim timer hello interval Undo pim timer hello Syntax probe-interval interval Undo probe-interval Pim triggered-hello-delayRelated command timer join-prune PIM view Probe-interval PIM view Register-policy PIM view Register-suppression-timeout PIM viewRelated command register-suppression-timeout PIM view Syntax register-suppression-timeout interval 1421 Undo register-suppression-timeoutRegister-whole-checksum PIM view Syntax register-whole-checksum Undo register-whole-checksum Syntax source-lifetime interval Undo source-lifetime Reset pim control-message countersRelated command state-refresh-interval PIM view Source-lifetime PIM view Syntax source-policy acl-number Undo source-policy Spt-switch-threshold PIM viewUndo spt-switch-threshold group-policy acl-number Source-policy PIM view PIM Configuration Commands 1425 Ssm-policy PIM viewState-refresh-interval PIM view Syntax ssm-policy acl-number Undo ssm-policy Syntax state-refresh-ttl ttl-value Undo state-refresh-ttl State-refresh-rate-limit PIM viewState-refresh-ttl PIM view 1427 By default, the TTL value of state refresh messages isStatic-rp PIM view Undo static-rp rp-address Related command pim timer hello Timer hello PIM viewTimer join-prune PIM view Related command display pim rp-infoand auto-rp enable Related command spt-switch-threshold PIM view Timer spt-switch PIM viewRelated command pim timer join-prune Syntax timer spt-switch interval Undo timer spt-switch PIM Configuration Commands Display multicast ipv6 forwarding-table IPV6 Multicast Routing Forwarding Configuration CommandsRelated command multicast ipv6 boundary Display multicast ipv6 boundary IPV6 Multicast Routing and Forwarding Configuration Commands 1433 Display multicast ipv6 minimum-hoplimitValues and meanings of the Flags field Display multicast ipv6 routing-table Related command multicast ipv6 minimum-hoplimit 1435 Related command display multicast ipv6 forwarding-tableDisplay multicast ipv6 rpf-info Multicast ipv6 boundary 1437 Related command display multicast ipv6 boundaryMulticast ipv6 forwarding-table downstream-limit Multicast ipv6 load-splitting Multicast ipv6 forwarding-table route-limit 1439 Multicast ipv6 longest-matchMulticast ipv6 minimum-hoplimit Related command display multicast ipv6 minimum-hoplimit Multicast ipv6 routing-enable 1441 Reset multicast ipv6 forwarding-tableReset multicast IPv6 routing-table Sysname reset multicast ipv6 routing-table ff03101 Display mld group MLD Configuration Commands Information of all interfaces running MLD Description on the fields of the display mld group commandDisplay mld interface 1445 Display mld routing-table Syntax fast-leave group-policy acl6-number Undo fast-leave Fast-leave MLD view 1447 Last-listener-query-intervalMax-response-time MLD view Syntax max-response-time interval Undo max-response-time Syntax mld Mld enableSyntax mld enable Undo mld enable Mld Mld group-policy Related command mldExample # Enable MLD on Ethernet 1/0 Mld fast-leave Mld last-listener-query-interval 1451 Mld max-response-timeMld require-router-alert Syntax mld robust-count robust-value Undo mld robust-count Mld robust-count Undo mld send-router-alert Mld send-router-alertMld static-group Mld send-router-alert 125 x 2 + 10 / 2 = 255 seconds Mld timer other-querier-presentMld timer other-querier-present interval Undo mld timer other-querier-present Mld version Mld timer querySyntax mld timer query interval Undo mld timer query Related command mld version Mld require-router-alert and send-router-alert MLD view Reset mld groupRequire-router-alert MLD view Require-router-alert 1457 Related command display mld groupRobust-count MLD view # Clear all MLD forwarding entries on Ethernet 1/0 View MLD view Timer other-querier-present MLD viewBy default, the MLD querier robustness variable is Send-router-alert MLD view Timer query interval Timer query MLD viewRelated command Example # Globally set the MLD version to MLDv2 Version MLD view Syntax bsr-policy acl6-number Undo bsr-policy IPV6 PIM Configuration CommandsBsr-policy IPv6 PIM view Bsr IPv6 PIM view Bsr hash-length IPv6 PIM view Related command c-bsr IPv6 PIM view on Syntax c-bsr interval interval Undo c-bsr interval Example # Set the bootstrap timeout time to 150 secondsBsr holdtime IPv6 PIM view Bsr interval IPv6 PIM view Bsr IPv6 PIM view and c-bsr holdtime IPv6 PIM view Related command c-bsr IPv6 PIM viewBsr priority IPv6 PIM view Rp IPv6 PIM view 1465 Rp advertisement-interval IPv6 PIM viewView IPv6 PIM view Example # Set the global C-RP-Adv interval to 30 seconds Related command c-rp IPv6 PIM viewExample # Set the global C-RP timeout time to 200 seconds Rp holdtime IPv6 PIM view Syntax crp-policy acl6-number Undo crp-policy Related command c-bsr IPv6 PIM view and c-rp IPv6 PIM viewCrp-policy IPv6 PIM view Display pim ipv6 bsr-info Syntax display pim ipv6 claimed-route ipv6-source-address Display pim ipv6 claimed-route Display pim ipv6 control-message counters BSR Unacknowledged graft messages Display pim ipv6 graftsDisplay pim ipv6 interface Display pim ipv6 grafts Interface PIM version PIM mode Specified IPv6 PIM neighbor Display pim ipv6 join-prunePIM-SM and IPv6 PIM-SSM respectively To send on the specified interface Display pim ipv6 neighbor 1475 Display pim ipv6 routing-table Example # View the content of the IPv6 PIM routing table Related command display multicast ipv6 routing-tableon 1477 Display pim ipv6 rp-infoSyntax display pim ipv6 rp-info ipv6-group-address Syntax embedded-rp acl6-number Undo embedded-rp acl6-number Embedded-rp Example # Set the router priority for DR election to Related command pim ipv6 hello-optiondr-priorityHello-option dr-priority IPv6 PIM view Hello-option holdtime IPv6 PIM view Hello-option neighbor-tracking IPv6 PIM view Hello-option lan-delay IPv6 PIM viewRelated command pim ipv6 hello-option holdtime Example # Set the prune delay to 200 milliseconds globally Holdtime assert IPv6 PIM view Related command pim ipv6 hello-optionneighbor-trackingExample # Disable join suppression globally Hello-option override-interval IPv6 PIM view Holdtime join-prune IPv6 PIM view 1483 Related command jp-queue-size IPv6 PIM viewJp-pkt-size IPv6 PIM view Jp-queue-size IPv6 PIM view Syntax pim ipv6 Undo pim ipv6 Related command multicast ipv6 routing-enableonPim ipv6 Pim ipv6 bsr-boundary Syntax pim ipv6 dm Undo pim ipv6 dm Related commands pim ipv6 sm, ssm-policy IPv6 PIM viewExample # Enable IPv6 PIM-DM on Ethernet 1/0 Pim ipv6 dm Pim ipv6 hello-option holdtime Related command hello-optiondr-priority IPv6 PIM viewRelated command hello-option holdtime IPv6 PIM view Pim ipv6 hello-option dr-priority 1487 Pim ipv6 hello-option lan-delayPim ipv6 hello-option neighbor-tracking Pim ipv6 holdtime assert Related command hello-optionneighbor-tracking IPv6 PIM viewExample # Disable join suppression on Ethernet 1/0 Pim ipv6 hello-option override-interval 1489 Pim ipv6 holdtime join-prunePim ipv6 require-genid Syntax pim ipv6 require-genid Undo pim ipv6 require-genid Undo pim ipv6 sm Pim ipv6 smPim ipv6 state-refresh-capable Pim ipv6 sm 1491 Pim ipv6 timer graft-retryPim ipv6 timer hello Related command timer join-prune IPv6 PIM view Pim ipv6 timer join-prunePim ipv6 triggered-hello-delay Related command timer hello IPv6 PIM view Example # Set the probe time to 6 seconds Related command register-suppression-timeout IPv6 PIM viewProbe-interval IPv6 PIM view Register-policy IPv6 PIM view Register-suppression-timeout IPv6 PIM view 1495 Reset pim ipv6 control-message countersRegister-whole-checksum IPv6 PIM view Syntax source-policy acl6-number Undo source-policy Related command state-refresh-interval IPv6 PIM viewSource-lifetime IPv6 PIM view Source-policy IPv6 PIM view 1497 Spt-switch-threshold IPv6 PIM viewUndo spt-switch-threshold group-policy acl6-number Syntax ssm-policy acl6-number Undo ssm-policy Ssm-policy IPv6 PIM view 1499 State-refresh-hoplimitState-refresh-interval IPv6 PIM view Example # Set the state refresh interval to 70 seconds State-refresh-rate-limit IPv6 PIM viewStatic-rp IPv6 PIM view 1501 Timer hello IPv6 PIM viewRelated command display pim ipv6 rp-info Undo static-rp ipv6-rp-address Related command pim ipv6 timer join-prune Timer join-prune IPv6 PIM viewTimer spt-switch IPv6 PIM view Related command pim ipv6 timer hello 1503 Related command spt-switch-threshold IPv6 PIM view IPV6 PIM Configuration Commands Display multicast-domain vpn-instance share-group Multicast VPN Configuration CommandsDisplay multicast-domain vpn-instance switch-group receive Count 1507 Display multicast-domain vpn-instance switch-group send Multicast-domain holddown-time 1509 Multicast-domain log switch-group-reuseMulticast-domain share-group View VPN instance view Multicast-domain switch-delay 1511 Multicast-domain switch-group-poolUndo multicast-domain switch-group-pool Sysname system-view Sysname ip vpn-instance mvpn Display mpls fast-forwarding cache verbose Mpls Basics Configuration CommandsDisplay mpls fast-forwarding cache # Display all ILM entries Display mpls ilmSyntax display mpls ilm label include text 1515 Related command display mpls statistics interfaceDisplay mpls interface Display mpls label label-value1 to label-value2 all Display mpls label Mpls ldp system view , mpls ldp interface view Display mpls ldpDisplay mpls ldp all verbose begin exclude include LSR ID Description on the fields of the display mpls ldp commandDisplay mpls ldp cr-lsp 1519 Related command display mpls lspDisplay mpls ldp interface All Displays all information # Display detailed information about all interfaces Example # Display information about all LDP interfaces Established by LDP Display mpls ldp IspAll Displays information about all LSPs established by LDP Dest-addr Destination address of the LSP Display mpls ldp peer Related command display mpls ldp 1523 Example # Display information about all peers# Display detailed information about all peers Example # Display information about remote peer BJI Display mpls ldp remote-peer 1525 Display mpls ldp session MD5 Example # Display information about sessions# Display detailed information about all sessions LAM 1527 Display mpls ldp vpn-instance Outgoing-interface Outgoing interface of the LSPs Display mpls lspExample # Display information about VPN instance vpn1 Incoming-interface Incoming interface of the LSPs Asbr Displays information about Asbr established LSPs Exclude Excludes the specified FECInclude Includes the specified FEC Dest-addr Destination address FEC Description on the fields of the display mpls lsp commandExample # Display information about all LSPs # Display detailed information about all LSPs Syntax display mpls nhlfe token include text Display mpls lsp statisticsDisplay mpls nhlfe Syntax display mpls lsp statistics # Display all Nhlfe entries Display mpls route-state 1533 Display mpls static-lsp # Display detailed information about static LSPs Display mpls statistics interfaceExample # Display brief information about static LSPs 1535 Related command statistics intervalExample # Display Mpls statistics for all interfaces Syntax display mpls statistics lsp index all name lsp-name Display mpls statistics lsp 1537 Example # Display Mpls statistics for all LSPs Are both Du-readvertise timerSyntax du-readvertise timer value Undo du-readvertise timer Du-readvertise Syntax graceful-restart mpls ldp Graceful-restart Mpls LDP viewGraceful-restart mpls ldp View Mpls LDP view Syntax graceful-restart timer reconnect timer Graceful-restart timer neighbor-livenessGraceful-restart timer reconnect Related commands graceful-restart Mpls LDP view 1541 Graceful-restart timer recoveryUndo graceful-restart timer reconnect Syntax hops-count hop-number Undo hops-count Related command loop-detect,path-vectorsHops-count Label advertise Undo label-distribution Label-distributionUndo label advertise Label-distribution independent ordered Undo label-retention Label-retentionLabel-retention conservative liberal Lsp-trigger Related command hops-count,path-vectorsUse the undo lsp-trigger command to restore the default Loop-detect Undo lsr-id # Configure the LDP LSR ID of LDP instance named vpn1Lsr-id Syntax lsr-idlsr-id Undo mpls Md5-passwordMpls Syntax mpls View System view/interface view Related command mpls lsr-id# Enable Mpls for interface Ethernet 1/0 Mpls ldp system view 1549 # Enable LDP for VPN instance vpn1Mpls ldp interface view Syntax mpls ldp Undo mpls ldp Undo mpls ldp advertisement Mpls ldp advertisementMpls ldp advertisement dod du Example # Create a remote peer entity named BJI Mpls ldp timer hello-holdRelated command remote-ip Mpls ldp remote-peer Mpls ldp timer keepalive-hold Syntax mpls lsr-id lsr-id Undo mpls lsr-id Mpls ldp transport-addressMpls lsr-id View Interface view/MPLS LDP remote peer view Example # Set the LSR ID to Mtu-signallingRelated command display mpls interface Syntax mtu-signalling Undo mtu-signalling Syntax path-vectors pv-number Undo path-vectors Related command loop-detect,hops-countPath-vectors Ping lsp Syntax remote-ip ip-address Undo remote-ip Remote-ip Reset mpls fast-forwarding cache Reset mpls fast-forwarding cacheReset mpls ldp Related command mpls ldp remote-peer Syntax reset mpls statistics lsp index all name lsp-name Reset mpls statistics interfaceReset mpls statistics lsp Lsp-name Name for the LSP, a string of 1 to 15 characters Snmp-agent trap enable mplsRelated command display mpls statistics lsp Static-lsp egress Undo static-lsp ingress lsp-name Static-lsp ingress 1561 Static-lsp transitUndo static-lsp transit lsp-name Syntax tracert lsp -a source-ip-exp Related command static-lsp egress, static-lsp ingressStatistics interval Tracert lsp Undo ttl expiration pop Ttl expiration pop commandTtl expiration Ttl expiration pop Ttl propagate Add hop Mpls TE Configuration Commands Syntax display explicit-path pathname Delete hopDisplay explicit-path Syntax delete hop ip-address 1567 Display isis traffic-eng advertisements# Display the latest TE information advertised by IS-IS TE Intf Addr 1569 Display isis traffic-eng linkVerbose Displays details Vpn-instance vpn-instance-name Specifies a VPN instance. Display isis traffic-eng network 1571 Display isis traffic-eng statistics Display isis traffic-eng sub-tlvs Related command te-set-subtlv Display mpls rsvp-te Label switched Router ID, # Display RSVP-TE information for interface Ethernet 1/0 Display mpls rsvp-te establishedBegin include exclude regular-expression About RSVP-TE globally or for an interface Spaces Display mpls rsvp-te peerFilters output by regular expression 1577 Display mpls rsvp-te psb-content Erhopstrict X.X Display mpls rsvp-te requestRSVP-TE requests on the specified or all interfaces 1579 Display mpls rsvp-te reservation LSP ID Display mpls rsvp-te rsb-content1581 Tunnel Dest 1583 Display mpls rsvp-te sender RSVP-TE is displayed Display mpls rsvp-te statisticsGlobal Display global RSVP-TE information Interface is specified 1585 # Display the RSVP-TE statistics of interface Serial 1/0 Ip-address prefix-length arguments Display mpls static-cr-lsp 1587 Display mpls te cspf tedb# Display detailed information about all static CR-LSPs IGP Mpls LSR ID IGP # Display the Tedb information of IGP area# Display all Tedb information 1589 # Display the Tedb information of all nodes # Display Tedb information for a specified interface address Links of all interfaces if no interface is specified Display mpls te link-administration admission-control 1593 Display mpls te link-administration bandwidth-allocationDescription on fields of the command Egress ingress remote transit name name incoming-interface Display mpls te tunnel LSP-ID # Display detailed information about Mpls TE tunnels1595 # Display the paths that all Mpls TE tunnels traverse Display mpls te tunnel pathLsr-id Ingress LSR ID, in dotted decimal notation Syntax display mpls te tunnel-interface Display mpls te tunnel statisticsDisplay mpls te tunnel-interface Syntax display mpls te tunnel statistics CR-LSP 1599 Display ospf mpls-te Area ID TE enabled Ospf area ID LSA Type 1601 Display ospf traffic-adjustmentSyntax display ospf process-id traffic-adjustment # Display statistics about tunnels Display tunnel-infoSyntax display tunnel-info tunnel-id all statistics View Ospf view/IS-IS view Enable traffic-adjustmentEnable traffic-adjustment advertise # Enable IGP shortcut when the IGP protocol is IS-IS List hop Explicit-path 1605 Modify hopView Explicit path view Mpls rsvp-te Mpls rsvp-te authenticationMpls rsvp-te authentication cipher plain auth-key Undo mpls rsvp-te authentication 1607 Mpls rsvp-te blockade-multiplier Syntax mpls rsvp-te hello Undo mpls rsvp-te hello Related command mpls rsvp-te timer refreshMpls rsvp-te graceful-restart Mpls rsvp-te hello 1609 # Enable Rsvp hello extension on interface Ethernet 1/0Mpls rsvp-te hello-lost Example # Set the keep multiplier to five Related command mpls rsvp-te timer helloMpls rsvp-te keep-multiplier Mpls rsvp-te reliability Mpls rsvp-te srefresh Mpls rsvp-te resvconfirm Mpls rsvp-te timer graceful-restart restart Mpls rsvp-te timer graceful-restart recovery Example # Set the hello interval to five seconds Mpls rsvp-te timer helloMpls rsvp-te timer refresh Related command mpls rsvp-te hello, mpls rsvp-tehello-lost Undo mpls rsvp-te timer retransmission Mpls rsvp-te timer retransmissionRelated command mpls rsvp-tekeep-multiplier Undo mpls te # Enable Mpls TE on interface Ethernet 1/0Mpls te Syntax mpls te Undo mpls te auto-bandwidth Related command mpls te link administrative groupMpls te affinity property Mpls te auto-bandwidth Undo mpls te backup Mpls te backupRelated command mpls te timer auto-bandwidth Mpls te backup hot-standby ordinary Example # Enable hot backup on tunnel Mpls te backup bandwidthWith backup enabled, the record route Undo mpls te bandwidth Mpls te bandwidthMpls te bandwidth change thresholds Mpls te bandwidth bc0 bc1 bandwidth View Tunnel interface view Mpls te commitSyntax mpls te commit Mpls te cspf Mpls te cspf timer failed-linkRelated command mpls te cspf Example # Set the failed link timer to 50 seconds Syntax mpls te fast-reroute Undo mpls te fast-reroute Mpls te fast-rerouteMpls te fast-reroute bypass-tunnel 1623 Mpls te igp advertiseDescription Example # Set the hold time to 10000 milliseconds Undo mpls te igp shortcut Mpls te igp metricMpls te igp shortcut Mpls te igp shortcut isis ospf Syntax mpls te loop-detection Undo mpls te loop-detection Mpls te link administrative groupRelated command mpls te affinity property Mpls te loop-detection Mpls te max-reservable-bandwidth Mpls te max-link-bandwidth Syntax mpls te metric value Undo mpls te metric Related command mpls te path metric-typeMpls te metric Undo mpls te max-reservable-bandwidth Example In Mpls view Related command mpls te metricMpls te path explicit-path Mpls te path metric-type Syntax mpls te record-route label Undo mpls te record-route Mpls te priorityMpls te record-route Undo mpls te priority Mpls te reoptimization Mpls te reoptimization user viewMpls te reoptimization tunnel interface view Mpls te retry Mpls te resv-style Mpls te route-pinning Related command mpls te timer retryExample # Set the maximum number of tunnel setup retries to Example # Enable route pinning Mpls te tie-breaking least-fill most-fill random Mpls te signal-protocolMpls te signal-protocol crldp rsvp-te static Mpls te tie-breaking Related command mpls te auto-bandwidth Mpls te timer auto-bandwidthBy default, automatic bandwidth adjustment is disabled 1635 Mpls te timer fast-rerouteMpls te timer retry Syntax mpls te timer retry second Undo mpls te timer retry Mpls te vpn-binding Related command mpls te retryExamples # Configure the tunnel ID as Mpls te tunnel-id Next hop Mpls-te enableSyntax mpls-te enable Undo mpls-te Related command opaque-capability Opaque-capability Related command delete hop Static-cr-lsp egress Reset mpls rsvp-te statisticsReset mpls te auto-bandwidth adjustment timers Syntax reset mpls te auto-bandwidth adjustment timers Static-cr-lsp ingress Undo static-cr-lsp transit tunnel-name Static-cr-lsp transitCR-LSP on the ingress or a transit node Value Sub-TLV in the range 19 to Use the undo te-set-subtlvcommand to restore the default# Configure sub-TLVs for IS-IS process Bw-constraint Sets the bandwidth constraint sub-TLV Cost-style on If no level is specified, IS-IS TE applies to Level-1-2 Mpls TE Configuration Commands Ccc interface in-label out-label Mpls L2VPN Configuration Undo ce ce-name Ccc interface out-interface 1647 Connection# Create a CE named ce2 for a VPN View Mpls L2VPN CE view Tunnel select-seq load-balance-number on Related command route-distinguisher Mpls L2VPN viewDisplay bgp l2vpn CE ID 1649 Verbose Peer Local 1651 Pref Preference # Display information about all CCC connections Display cccSyntax display ccc ccc-name ccc-nametype local remote # Display information about all local CCC connections Down Display l2vpn ccc-interface vc-type 1655 Configured on the routerConfigured on the CE interface Display mpls l2vc VC ID VC ID Vpn-name local-ce remote-ce Display mpls l2vpn # Display information about local CEs of L2VPN vpn1 Description on the fields of the display mpls l2vpn command# Display information about L2VPN vpn1 1659 Display mpls l2vpn connection# Display information about remote CEs of L2VPN vpn1 Status Status of the connection Peer-id Description on the fields of mpls l2vpn connection summary Example # Display Mpls L2VPN forwarding information Display mpls l2vpn forwarding-infoDisplay mpls static-l2vc 1663 L2vpn-familySyntax l2vpn-family Undo l2vpn-family Related command tunnel select-seqload-balance-numberonMpls l2vc Syntax mpls l2vpn Undo mpls l2vpn Mpls l2vpnMpls l2vpn vpn-name Example # Create a Martini Mpls L2VPN connection Undo mpls static-l2vc Mpls static-l2vc destination# Create Kompella VPN named vpn2 and enter Mpls L2VPN view Example # Set the MTU for Kompella connections to Reset bgp l2vpnMtu Mpls L2VPN view Syntax mtu mtu Route-distinguisher route-distinguisher Re-create the VPN using the new RDTakes effect only when it is configured with an RD Route-distinguisher Mpls L2VPN view 1669 Vpn-target Mpls L2VPN viewExample # Associate VPN vpn1 with VPN targets Mpls L2VPN Configuration Commands View Policy routing view Apply access-vpn vpn-instanceDefault local-preference BGP-VPNv4 subaddress family view Syntax default local-preference value Default med BGP-VPNv4 subaddress family view 1673 Description VPN instance viewDisplay bgp vpnv4 all routing-table Example # Display all BGP VPNv4 routing information 1675 Display bgp vpnv4 groupAll Specifies all VPNv4 peers Display bgp vpnv4 network # Display all BGP VPNv4 AS path information Display bgp vpnv4 pathsDisplay bgp vpnv4 all vpn-instance vpn-instance-name paths Be displayed VPNv4 peers Display bgp vpnv4 peerVerbose Displays detailed information 1679 # Display detailed information about BGP VPNv4 peer # Display all BGP VPNv4 peer information 1681 Display bgp vpnv4 route-distinguisher routing-table 1683 Related command route-distinguisher VPN instance viewExample # Display the BGP VPNv4 routing information of RD Fields of the above output 1685 Display bgp vpnv4 routing-table labelAll Specifies all VPNv4 peers Display bgp vpnv4 vpn-instance routing-table 1687 Display fib vpn-instance vpn-instance-name include string Display fib statistics vpn-instanceDisplay fib vpn-instance Display fib statistics vpn-instance 1689 Display ip vpn-instance# Display detailed information about a VPN instance Example # Display information about all Ospf sham links Related command sham-linkDisplay ospf sham-link Syntax display ospf process-id sham-link area area-id Tunneling policy or all tunneling policies Display tunnel-policy# Display information about Ospf sham links in area Display tunnel-policy all policy-name tunnel-policy-name # Display tunneling policy aaa Example # Configure the Ospf domain IDDomain-id 1693 Export route-policyFilter-policy export BGP-VPNv4 subaddress family view Filter-policy import BGP-VPNv4 subaddress family view 1695 Import route-policyIp binding vpn-instance Vpnv4 Enters BGP-VPNv4 subaddress family view Ip vpn-instanceIpv4-family View BGP view 1697 Peer advertise-community BGP-VPNv4 subaddress family view Peer as-path-acl BGP-VPNv4 subaddress family view Peer allow-as-loop 1699 Peer default-route-advertise vpn-instance Peer filter-policy BGP-VPNv4 subaddress family view Peer enableRelated command peer upe 1701 Peer group Peer label-route-capability BGP view/BGP VPN instance view Peer ip-prefix BGP-VPNv4 subaddress family view 1703 Peer next-hop-invariable BGP-VPNv4 subaddress family view Peer public-as-only BGP-VPNv4 subaddress family view Peer next-hop-local 1705 Peer reflect-client Peer upe Peer route-policy BGP-VPNv4 subaddress family view 1707 Command applies to inter-provider VPN option B schemesPolicy vpn-target Syntax policy vpn-target Undo policy vpn-target Reflector culster-id Reflect between-clients 1709 Refresh bgp vpn-instance Refresh bgp vpnv4 Reset bgp vpn-instance 1711 Reset bgp vpn-instance dampeningReset bgp vpn-instance flap-info Syntax route-distinguisher route-distinguisher Reset bgp vpnv4Route-distinguisher VPN instance view Syntax route-tag tag-value Undo route-tag Then re-create the VPN instance and re-configure a new RDRoute-tag Instance Import-route Ospf view on Example # Configure the route tag for Ospf process 100 asRouting-table limit View Ospf area view Rr-filterSham-link Undo rr-filter Mpls L3VPN Configuration Commands Undo tnl-policy Related command tunnel select-seqload-balance-numberTnl-policy VPN instance view Tunnel-policy Undo tunnel select-seq Load-balance-number command can be usedTunnel select-seq load-balance-number 1719 Vpn-instance-capability simpleVpn-target VPN instance view View Ospf multi-instance view Mpls L3VPN Configuration Commands Vam server vpn , authentication-method VAM Server Configuration CommandsAuthentication-algorithm Authentication-method Display vam server address-map Vam server vpn , authentication-algorithm 1723 Display vam server statisticSyntax display vam server statistic all vpn vpn-name Description on the fields of display vam server address-map # Display statistics of VPN domain 1 on the VAM server Example # Display statistics of the VAM server Undo hub private-ip private-ip-address Related command vam server vpnEncryption-algorithm Hub private-ip Keepalive interval Related command vam server vpn, keepalive retry Syntax keepalive retry retry-times Undo keepalive retry Related command vam server vpn, keepalive intervalKeepalive retry Pre-shared-key VPN domain view Example # Enable the VAM server function of VPN domain Server enableSyntax server enable Undo server enable Related command vam server vpn, vam server enable Vam server ip-address Vam server enableRelated command Vam server vpn, server enable Example Syntax vam server vpn vpn-name Undo vam server vpn vpn-name Vam server vpn 100 VAM Client Configuration CommandsClient enable Related command vam client name, and vam client enable Example # Display the status information of VAM client abc Cipher Specifies a pre-shared key in cipher text Pre-shared-key VAM client viewPre-shared-key cipher simple key-string VAM client view Syntax resend interval time-interval Undo resend interval No pre-shared key is configured by defaultRelated command vam client name Resend interval 1735 Server primary ip-addressServer secondary ip-address User Vam client enableBy default, no local username or password is configured Example # Set the local username and password both to user An interface Vam client name and client enableBy default, no VAM client is configured Vam client name Example # Specify the VAM client abc to belong to VPN VpnUndo vpn Display ipsec profile Ipsec Profile Configuration CommandsRelated command ipsec profile system view 101 Ipsec profile system view Inbound ESP setting 1741 Ipsec Profile Configuration Commands Associated with the VAM client Dvpn Tunnel Configuration Commands102 Display dvpn session Dumb Dvpn session dumb-time 1745 Dvpn session idle-timeIpsec profile tunnel interface view Undo ipsec profile ipsec-profile-name&1-6 Undo keepalive Keepalive Syntax tunnel-protocol dvpn udp Undo tunnel-protocol Related command Interface tunnel on ExampleTunnel-protocol dvpn udp Syntax vam client client-name Undo vam client Related command interface tunnel onExample # Configure the Dvpn tunnel mode Vam client 103 GRE Configuration CommandsRelated command interface tunneland source Down Example # Display information about interface Tunnel0 1751 Syntax gre checksum Undo gre checksum Gre checksum 1753 Related command interface tunnelGre key Undo gre key Syntax interface tunnel number Undo interface tunnel number 1755 Syntax tunnel-protocol gre ipv6 Undo tunnel-protocol Tunnel-protocol gre Undo allow L2TP Configuration Commands104 Allow l2tp Sessions Related command l2tp-groupRelated command Display l2tp tunnel Example Display l2tp session 1759 Display l2tp tunnelSyntax display l2tp tunnel Syntax l2tp enable Undo l2tp enable L2tp enableL2tp sendaccm enable Related command allow l2tp L2tp-group L2tpmoreexam enableL2tp enable Use the undo l2tp-group command to remove an L2TP group Mandatory-lcp Related command allow l2tp and start l2tpRelated command Mandatory-lcp Example Mandatory-chap View L2TP group view Reset l2tp tunnelRelated command mandatory-chap Undo mandatory-lcp Start l2tp Tunnel authenticationRelated command display l2tp tunnel Syntax tunnel authentication 1765 Undo tunnel authenticationTunnel avp-hidden Syntax tunnel avp-hidden Undo tunnel avp-hidden Tunnel name Tunnel flow-control Tunnel timer hello Tunnel password L2TP Configuration Commands Filed Description Traffic Policing TP Configuration CommandsDescription on the fields of the display qos car command Display qos car interface Display qos carl carl-index Description on the fields of the display qos carl commandDisplay qos carl Qos car 1771 Undo qos carl carl-index Qos carl 1773 Examples # Configure Carl rule 1 with packet precedence Traffic Policing TP Configuration Commands Display qos gts interface Traffic Shaping Configuration CommandsDescription on the fields of the display qos gts command 106 Undo qos gts any acl acl-number queue queue-number Qos gts 1777 Related commands acl on Traffic Shaping Configuration Commands Display qos lr interface Line Rate Configuration CommandsDescription on the fields of the display qos lr command 107 Undo qos lr inbound outbound Qos lr interface viewQos lr layer 2 interface view or port group view 1781 Layer 2 module interface view, port group viewInterfaces is 4 or 9, this argument is not supported Line Rate Configuration Commands Display traffic classifier Defining Class Commands108 Match-criteria Class match rules. The values are as follow If-matchUndo if-match not match-criteria Class view Qos-local-id 1785Value Description Rtp start-port End-port Define Mpls EXP precedence matching rule 1787 Related commands traffic classifier# Define a class to match ACL # Define matching rule for all packets # Define a class to match the ACL named flow# Define a class to match IPV6 ACL # Define a class to match the IPv6 ACL named flow Undo traffic classifier tcl-name Traffic classifierTraffic classifier tcl-name operator and or Examples # Define a class named as class1 By default, the relation is operator Undo car Defining Traffic Behavior Commands109 Car Qos policy , traffic behavior , classifier behavior Display traffic behavior Undo filter FilterGts Filter deny permit View Traffic behavior view RedirectUndo gts Undo redirect 1795 Remark atm-clpSyntax remark atm-clp atm-clp-value Undo remark atm-clp Syntax remark dscp dscp-value Undo remark dscp Remark dot1pRemark dscp Syntax remark dot1p 8021p Undo remark dot1p 1797 Remark fr-deSyntax remark fr-de fr-de-value Undo remark fr-de Syntax remark mpls-exp exp-value Undo remark mpls-exp Remark ip-precedenceRemark mpls-exp Examples # Remark the DE bit in FR packets to 1799 Remark qos-local-idTraffic behavior Examples # Define a traffic behavior named behavior1 Classifier behavior Defining Policy CommandsRelated commands qos policy 110 Tcl-name Class name in the policy Description on the fields of the display qos policy commandSystem-defined Policy pre-defined by the system User-defined Policy pre-defined by the user 1803 Display qos policy interface EXP Qos apply policy interface view 1805 Qos apply policy layer 2 interface view or port group view Syntax qos policy policy-name Undo qos policy policy-name Qos policy 1807 Defining Policy Commands 1809 Fifo Queuing Configuration Commands111 Qos fifo queue-length Fifo Queuing Configuration Commands Display qos pq interface PQ Configuration CommandsRelated commands qos pq 112 Syntax qos pq pql pql-index Undo qos pq Related commands qos pq, qos pq pqlQos pq Examples # Display PQLs 1813 Qos pql default-queueQos pql inbound-interface Examples # Apply the priority list 12 to the Ethernet 1/0 Queue-key Key-value Description By default, no classification rule is configuredQos pql protocol Description on values of queue-key and key-value 1815 Qos pql queue PQ Configuration Commands Display qos cq interface CQ Configuration CommandsRelated commands qos cq 113 Syntax qos cq cql cql-index Undo qos cq Default values will not be displayedQos cq Examples # Display information about a CQL 1819 Qos cql default-queueExamples # Assign default queue 2 to CQL Qos cql inbound-interface Descriptions of values of queue-key and key-value Qos cql protocol 1821 Qos cql queue Examples # Specify byte-count of queue 2 in the CQL 5 to Qos cql queue servingUndo qos cql cql-indexqueue queue-numberserving Display qos wfq interface WFQ Configuration CommandsRelated commands qos wfq 114 Display interface, display qos wfq interface Qos wfqUndo qos wfq Qos max-bandwidth CBQ Configuration Commands115 Display qos cbq interface Queue af 1827 Queue ef Queue wfq 1829 Queue-lengthWred Syntax wred dscp ip-precedence Undo wred Undo wred dscp dscp-value Wred dscp 1831 Wred ip-precedence Wred weighting-constant Display qos rtpq interface RTP Priority Queue Configuration CommandsDescription on the fields of the display qos rtpq command 116 Qos rtpq Qos rtpq 1835 Related commands qos reserved-bandwidth RTP Priority Queue Configuration Commands Qos qmtoken token-number QOS Token Configuration Commands117 Qos qmtoken QOS Token Configuration Commands Display qos map-table Priority Mapping Table Configuration CommandsRelated commands qos map-tabledot1p-Ip 118 Import Related commands display qos map-tableParameters in the default mapping table Qos map-table dot1p-Ip 1841 Priority Mapping Table Configuration Commands Undo qos priority Port Priority Configuration Commands119 Qos priority Port Priority Configuration Commands Qos trust Port Priority Trust Mode Configuration Commands120 Display qos trust interface Port Priority Trust Mode Configuration Commands 1847 Wred Configuration Commands121 Display qos wred interface Dscp Uses the Dscp value for calculating drop probability Qos wred enableQos wred dscp ip-precedence enable Undo qos wred enable 1849 By default, the dropping method of a queue is tail dropRelated commands qos wfq, display qos wred interface Qos wred dscp Undo qos wred ip-precedence ip-precedence Qos wred weighting-constantDiscard-probability discard-prob Calculate the average length of Wred queues Length, in the range 1 to 16. It defaults toWred with the qos wred enable command on it Qos wred enable, display qos wred interface Wred Configuration Commands Syntax display qos wred table table-name Wred Table Configuration Commands122 Display qos wred table Qos wred apply Qos wfq , qos wred enable , display qos wred interfaceQos wred queue table 1855 Related commands qos wred queue table in system viewQueue Wred Table Configuration Commands Qos cql protocol mpls exp Mpls QOS Configuration Commands123 If-match mpls-exp Qos pql protocol mpls exp Related commands qos cql protocol 1859 Related commands qos pql protocolExamples # Set EXP value of remarked Mpls packet to Mpls QOS Configuration Commands Dar protocol DAR Configuration Commands124 Dar max-session-count Protocol name Protocol type Pre-defined port number Protocols of pre-defined ports 1863 Undo dar protocol-rename user-defined-name # Restore the default name of the user-defined01 protocolDar protocol-rename Dar protocol-statistic 1865 Display dar informationUndo dar protocol-statistic Syntax display dar information Display dar protocol all protocol-name Display dar protocol 1867 Display dar protocol-rename Display dar protocol-rename Display dar protocol-statistic If-match protocol If-match protocol http Undo if-match not protocol rtp payload-type audio video Reset dar protocol-statisticIf-match protocol rtp # Deletes all statistics information Information, i.e. to restore the statistics toReset dar session All Deletes all statistics information DAR Configuration Commands # Define a traffic behavior named behavior FR QOS Configuration Commands125 Apply policy outbound Undo cir Related commands ebs, cir allow, cirCbs Cir Cir allow inbound outbound committed-information-rate Related commandsCir allow Cbs, ebs, cir allow Undo cq Related commands cbs, ebs, cirRelated commands fr congestion-threshold Congestion-threshold 1879 Related commands wfq, pq, fr pvc-pqDisplay fr class-map Display fr fragment-info Related commands fragment 1881 # Display FR fragment information of a certain interfaces Fr switch Display fr switch-table 1883 # Display PVC PQ information on FR interface Serial2/0 Display qos pvc-pq interfacePVC PQ on FR interface Fifo queue-length Related commands Cbs, cir allow, cir ExamplesEbs Fr congestion-threshold Related commands fr classRelated commands fr-class Fr class 1887 Related commands congestion-thresholdFr de del Fr del inbound-interface Related commands fr del inbound-interface,fr del protocolRelated commands fr de del, fr del protocol 1889 Related commands fr de del, fr del inbound-interfaceFr del protocol Protocol ip IP Undo fr pvc-pq Related commands pvc-pqFr pvc-pq Syntax fr traffic-policing Undo fr traffic-policing Related commands fr class, fr-class,fr dlciFr traffic-policing Fr traffic-shaping Undo fragment fragment-size Examples # Enable Frts on the serial interface Serial 1/0Fragment Fr-class Undo pq Related commands fr class, fr dlciRelated commands cq, wfq, fr pvc-pq Pvc-pq Number, in the range 2000 to RtpqUndo pvc-pq Fr pvc-pq Undo traffic-shaping adaptation becn interface-congestion Related commands fr traffic-shaping,cir allow, and cirTraffic-shaping adaptation Examples # Apply WFQ to the FR class test1 Related commands cq, pq, fr pvc-pqWfq Undo wfq Display dot1x 802.1X Configuration CommandsExample # Display 802.1x configuration information 126 Descriptions on the fields of the display dot1x command Dot1x Dot1xDot1x interface interface-list Undo dot1x interface interface-list Syntax dot1x authentication-method chap eap pap Dot1x authentication-methodRelated command display dot1x # Enable 802.1x globally Dot1x guest-vlan Undo dot1x authentication-method Dot1x guest-vlan vlan-id Undo dot1x guest-vlan Undo dot1x handshake Dot1x handshakeDot1x handshake Dot1x max-user user-number Undo dot1x max-user Dot1x max-userUndo dot1x max-user interface interface-list Dot1x port-control By default, the multicast trigger function is enabledDot1x multicast-trigger Dot1x port-method macbased portbased Undo dot1x port-method Dot1x port-method 1907 Dot1x quiet-periodSyntax dot1x quiet-period Undo dot1x quiet-period Undo dot1x retry Related command display dot1x, dot1x timerDot1x retry Dot1x supp-proxy-check 1909 Dot1x timer 1911 Reset dot1x statisticsExample # Set the server timeout timer to 150 seconds Reset dot1x statistics interface interface-list Example # Clear 802.1x statistics on port Ethernet 1/1 127 AAA Configuration CommandsAccess-limit Accounting default AAA Configuration Commands 1915 Accounting lan-accessAccounting login Related command accounting default, radius scheme Syntax accounting optional Undo accounting optional Undo accounting loginAccounting optional 1917 Accounting portal Accounting ppp Attribute Related command domain, radius schemeUndo attribute access-limit idle-cut ip location mac vlan Accounting voip Example # Set the IP address of local user user1 to Authentication defaultRelated command display local-user Local Performs local authentication None Does not perform any authentication Authentication lan-accessUndo authentication lan-access Local Performs local authentication Related command authentication default, radius scheme Authentication login 1923 Authentication portal Radius-scheme radius-scheme-name local Authentication pppUndo authentication ppp 1925 Authentication voipAuthorization command Related command authorization default, hwtacacs scheme Authorization default 1927 Authorization lan-access Related command authorization default, radius scheme Authorization login 1929 Authorization portal Authorization default , hwtacacs scheme , radius scheme Authorization pppAuthorization voip Undo authorization ppp Domain , radius scheme Cut connection Display connection # Display information about all AAA user connections Related command cut connection ExampleDescription on the fields of the display connection command Display domain Description on the fields of the display domain command Related command access-limit,domain, state Display local-user Related command local-user Description on the fields of display local-user Domain# Display information about all local users Undo domain isp-name State , display domain Domain defaultRelated command access-limit,state, display domain Domain default disable enable isp-name Domain aabbcc.net Idle-cutIp pool Domain Undo level Related command remote address onLevel Syntax level level Example # Add a local user named user1 Related command display local-user,service-typeLocal-user Example # Set the level of user user1 to Related command display local-user , password Local-user password-display-modePassword Self-service-url Service-type Syntax service-type ftp Undo service-type ftp Service-type ftpService-type ppp Related command service-type ppp and service-type ftp State active block State Syntax work-directory directory-name Undo work-directory Related command domainWork-directory # Place the current user user1 to the state of blocked 1947 AAA Configuration Commands Radius scheme Radius Configuration CommandsAccounting-on enable 128 Related command radius scheme, accounting-on enable Accounting-on enable intervalAccounting-on enable send Packets to be sent to a Radius server Data-flow-format Radius scheme viewGigabyte Mega-packet, or giga-packet Display radius scheme Related command display radius schemeRelated command radius scheme Example # Display the configurations of all Radius schemes 1953 Display radius statisticsDisplay radius statistics Example # Display statistics about Radius packets State statistictotal=1024 State statistics Dead 1955 On August 31 Display stop-accounting-bufferWhich is a string of 1 to 32 characters Time range, or user name Display radius scheme Key Radius scheme viewNas-ip Radius scheme view Undo primary accounting Related command radius nas-ipPrimary accounting Radius scheme view 1959 Primary authentication Radius scheme view Radius nas-ip Syntax radius client enable Undo radius clientExample # Enable the listening port of the Radius client Radius client Undo radius scheme radius-scheme-name Related command nas-ip Radius scheme viewRadius scheme Undo radius nas-ip Radius trap Example # Clear Radius statistics Reset radius statisticsReset stop-accounting-buffer Syntax reset radius statistics Undo retry Retry 1965 Retry realtime-accounting Undo secondary accounting Retry stop-accounting Radius scheme viewSecondary accounting Radius scheme view 1967 Secondary authentication Radius scheme view View Radius scheme view Security-policy-serverServer-type Syntax server-type extended standard Undo server-type Accounting Sets the status of the Radius accounting server Use the state command to set the status of a Radius serverPrimary Sets the status of the primary Radius server Secondary Sets the status of the secondary Radius server Stop-accounting-buffer enable Radius scheme view 1971 Timer quiet Radius scheme viewTimer realtime-accounting Radius scheme view Syntax timer quiet minutes Undo timer quiet Number of users Real-time accounting interval minute Timer response-timeout Radius scheme viewRelated command retry realtime-accounting,radius scheme User-name-format with-domain without-domain Related command radius scheme, retryUser-name-format Radius scheme view Radius Configuration Commands Data-flow-format Hwtacacs scheme view Hwtacacs Configuration CommandsRelated command display hwtacacs 129 Description on the fields of the display hwtacacs command Related command hwtacacs scheme Address or a loopback address Hwtacacs nas-ipScheme view , retry stop-accounting Hwtacacs scheme view Undo hwtacacs scheme hwtacacs-scheme-name Related command nas-ip Hwtacacs scheme viewHwtacacs scheme Nas-ip Hwtacacs scheme view Key accounting authentication authorization stringUndo key accounting authentication authorization string Key Hwtacacs scheme view Primary accounting Hwtacacs scheme view Related command hwtacacs nas-ip 1981 Primary authentication Hwtacacs scheme viewExample # Set the primary authentication server Accounting Clears Hwtacacs accounting statistics Primary authorizationReset hwtacacs statistics Undo primary authorization Retry stop-accounting Hwtacacs scheme view Secondary accounting Hwtacacs scheme view Secondary authentication Hwtacacs scheme viewSyntax secondary authentication ip-address port-number 1985 Secondary authorizationExample # Configure the secondary authentication server View Hwtacacs scheme view Stop-accounting-buffer enable Hwtacacs scheme viewExample # Configure the secondary authorization server 1987 Timer quiet Hwtacacs scheme viewTimer realtime-accounting Hwtacacs scheme view Timer response-timeout Hwtacacs scheme view Hwtacacs scheme User-name-format Hwtacacs scheme view Hwtacacs Configuration Commands All Displays all the firewall statistics information Packet Filter Firewall Configuration CommandsSwitch running a routing protocol Display firewall ethernet-frame-filter Fragments-inspect Firewall defaultSyntax firewall default permit deny Display firewall-statistics Firewall ethernet-frame-filter Firewall enableFirewall enable Undo firewall enable Firewall fragments-inspect Example # Enable fragments inspection Undo firewall fragments-inspect high low Firewall fragments-inspect high low number defaultFirewall fragments-inspect high low Firewall ipv6 fragments-inspect Firewall packet-filter Related command firewall fragments-inspect Undo firewall packet-filter ipv6 inbound outbound Reset firewall ethernet-frame-filterFirewall packet-filter ipv6 Outbound # Clear the firewall statistic information of Ethernet 1/0 Reset firewall-statisticsExample # Clear all the firewall statistic information Aging-time syn fin tcp udp seconds Aspf Configuration Commands131 Aging-time Aspf-policy # Set the TCP idle timeout period to 3000 seconds# Set the UDP idle timeout period to 110 seconds 2001 Display aspf allSyntax display aspf all Syntax display aspf interface Display aspf interface Display aspf session verbose Display aspf policyDisplay aspf session Syntax display aspf policy aspf-policy-number Display port-mapping 2005 Related command port-mappingFirewall aspf Example # Display all the information about port mapping Port-mapping Log enableSyntax log enable Undo log enable Example # Enable the session logging function of the Aspf Example # Map port 3456 to the FTP protocol Reset aspf sessionRelated command display port-mapping Syntax reset aspf session Aspf Configuration Commands DFIC-9FSW and MSR 20 Series Products MAC Authentication Configuration CommandsDisplay mac-authentication Syntax display mac-authentication interface interface-list MAC Addr Mac-authentication 2011 Mac-authentication domain Related command display mac-authentication Mac-authentication timer Mac-authentication user-name-format Reset mac-authentication statistics 133 NAT Configuration CommandsConnection-limit default action Connection-limit default amount Connection-limit policy Connection-limit enableConnection-limit enable Undo connection-limit enable 2017 Display connection-limit policyExample # Create a connection-limit policy numbered Syntax display connection-limit policy policy-numberall Display connection-limit statistics Information Display nat address-groupDisplay nat address-group View Any view Parameter None Different NAT sessions Display nat aging-timeDisplay nat all Display nat aging-time 2021 Description on some fields of the display nat all command Destination address Display nat connection-limit 2023 Display nat logMask-length The length of net mask, in the range 1 to Syntax display nat log Display nat outbound # View the NAT log configurationDescription on the fields of the display nat log command Display nat outbound Syntax display nat server Display nat serverDisplay nat session Syntax display nat statistics Display nat statisticsExample # Display the active NAT sessions Limit acl Display userlog export View Connection-limit policy view Limit modeSyntax limit mode amount Undo limit mode Tcp-syn udp seconds Nat address-groupNat aging-time Undo nat address-group group-number Nat alg 2031 Nat connection-limit-policy Nat log flow-active Nat log enable Undo nat log flow-begin Nat log flow-beginNat outbound Nat log flow-begin NAT Configuration Commands Syntax nat outbound static Undo nat outbound static # Configure the address poolNat outbound static Nat server NAT Configuration Commands 2037 Nat static # Remove the WWW server using the following commands 2039 Reset nat sessionSyntax reset nat session Userlog nat export host Reset userlog exportReset userlog nat logbuffer Related command display userlog export 2041 Related command userlog nat export source-ipRelated command userlog nat export host Userlog nat export source-ip Syntax userlog nat syslog Undo userlog nat syslog Userlog nat export versionUserlog nat syslog 134 PKI Configuration Commands Syntax ca identifier name Undo ca identifier Ca identifier Pki entity Certificate request entityCertificate request from Certificate request polling Certificate request modeSimple password * manual Undo certificate request mode 2047 Related command display pki certificateCertificate request url Undo certificate request polling count interval Undo country Common-nameCountry Syntax common-name name Undo common-name Undo crl update-period Crl update-periodCrl check disable enable Crl update-period hours Undo crl url Crl urlDisplay pki certificate 2051 Example # Display the local certificate Display pki certificate attribute-group Display pki certificate access-control-policy Example # Display the locally saved CRLs Related command pki retrieval-crl domain and pki domainDisplay pki crl domain Syntax display pki crl domain domain-name Undo ip FqdnIp PKI entity view Undo fqdn Undo locality Ldap-serverLocality Undo ldap-server Syntax organization org-name Undo organization OrganizationOrganizational-unit 2057 Pki certificate access-control-policyPki certificate attribute-group Syntax pki domain domain-nameundo pki domain domain-name Pki delete-certificatePki domain Undo pki entity entity-name Pki entityPki import-certificate Pki entity entity-name Pki request-certificate domain Related command pki domain Pki retrieval-certificate ca local domain domain-name Related command Pki domain ExamplePki retrieval-certificate Pki retrieval-crl domain Root-certificate fingerprint md5 sha1 string Pki validate-certificateRoot-certificate fingerprint Pki validate-certificate ca local domain domain-name 2063 Rule access control policy viewSyntax rule id deny permit group-name Undo rule id all Undo state Display portal acl Portal Configuration CommandsPortal authentication 135 Statistics on the specified interface Description on the fields of the display portal acl commandDisplay portal connection statistics All Displays portal connection statistics on all interfaces 2067 Syntax display portal free-rule rule-number Msgauthenack Msgauthorack Msgloginack MsglogoutackDisplay portal free-rule 2069 Related command portal free-ruleDisplay portal interface URL Related command portal serverDisplay portal server Syntax display portal server server-name Reqchallenge Display portal server statisticsAll Displays portal server statistics on all interfaces 2071 Syntax display portal tcp-cheat statistics Display portal tcp-cheat statistics 2073 Display portal userSpecified interface enabling portal Specified interface or all interfaces enabling portal Undo portal auth-network network-addressall Portal auth-network Undo portal free-rule rule-numberall Related command display portal userPortal delete-user Portal free-rule Portal resource-name Related command display portal free-rule 2077 Related command display portal serverPortal server Undo portal server server-name key port url Portal server method Reset portal connection statistics Reset portal tcp-cheat statistics Reset portal server statisticsReset portal tcp-cheat statistics Portal Configuration Commands Rsh RSH Configuration Commands136 INSTALL.LOG Time-range Common Configuration CommandsDescription on the fields of the display time-range command Display time-range Common Configuration Commands 2085 Common Configuration Commands 2087 IPV4 ACL Configuration Commands138 Acl # Delete the IPv4 ACL named flow Acl copy# Create IPv4 ACL 2002, giving the ACL a name of flow # Delete the IPv4 ACL with the number 2089 Acl nameSyntax acl name acl-name # Define the description of ACL Description for IPv4# Define the description of IPv4 ACL 2091 Description on the fields of the display acl commandDisplay acl Syntax display acl acl-numberall name acl-name # Clear statistics about IPv4 ACL flow Reset acl counterSyntax reset acl counter acl-number all name acl-name Rule in basic IPv4 ACL view 2093 Rule in advanced IPv4 ACL view TCP/UDP-specific parameters for advanced IPv4 ACL rules Icmp message Type Code Parameter Function Description Icmp-type 2097 Rule in Ethernet frame header ACL viewUndo rule rule-id View User-defined ACL view Rule in user-defined ACL view Syntax rule rule-idcomment text Undo rule rule-idcomment Support to this command varies by deviceRule comment for IPv4 # Create a user-defined ACL rule # Create a rule in ACL 5000 and define the rule description Step for IPv4# Create a rule in ACL 3000 and define the rule description # Create a rule in ACL 4000 and define the rule description 2101 Example # Set the rule numbering step to 2 for ACL IPV4 ACL Configuration Commands 2103 IPV6 ACL Configuration Commands139 Acl ipv6 # Delete the IPv6 ACL named flow Acl ipv6 copy# Create IPv6 ACL 2002, giving the ACL a name of flow # Delete the IPv6 ACL with the number 2105 Acl ipv6 nameSyntax acl ipv6 name acl6-name Syntax display acl ipv6 acl6-numberall name acl6-name Description for IPv6Display acl ipv6 # Create a description for IPv6 ACL 3000 to 3999 for advanced IPv6 ACLs Reset acl ipv6 counterAll All basic and advanced IPv6 ACLs 2000 to 2999 for basic IPv6 ACLs Undo rule rule-id fragment logging source time-range Rule in basic IPv6 ACL view# Clear the statistics about the IPv6 ACL named flow 2109 Rule in advanced IPv6 ACL view Time-range time-name Parameter Function Description Source sourceDestination dest Available ICMPv6 messages TCP/UDP-specific match criteria for advanced IPv6 ACL rulesICMPv6-specific match criteria for advanced IPv6 ACL rules Rule in simple IPv6 ACL view Parameters for simple IPv6 ACL rules View Simple IPv6 ACL view ICMPv6 messages definable in simple IPv4 ACL rules TCP/UDP-specific parameters for simple IPv6 ACL rulesICMPv6-specific parameters for simple IPv6 ACL rules 2115 Support for this command varies by deviceRule comment for IPv6 Example # Set the rule numbering step to 2 for IPv6 ACL Step for IPv6 2117 # Set the rule numbering step to 2 for IPv6 ACL IPV6 ACL Configuration Commands 140 Ipsec Configuration CommandsAh authentication-algorithm Cryptoswitch fabric enable Syntax display encrypt-card fast-switch Display encrypt-card fast-switch Ipsec policy system view Display ipsec policyDisplay ipsec policy brief name policy-name seq-number # Display detailed information about all IPSec policies Template group Display ipsec policy-templateIPSec policy template group 10000 Syntax display ipsec proposal proposal-name Related command ipsec proposalDisplay ipsec proposal Display ipsec sa Reset ipsec sa, ipsec sa global-duration Description on the fields of the display ipsec sa command Example # Display information about all IPSec sessions Related command reset ipsec sessionDisplay ipsec session Syntax display ipsec session tunnel-id integer Example # Display IPSec packet statistics Related command reset ipsec statisticsDisplay ipsec statistics Syntax display ipsec statistics 2129 Display ipsec tunnelSyntax display ipsec tunnel Encapsulation-mode Encrypt-card fast-switch Syntax esp encryption-algorithm 3des aes key-length des Esp authentication-algorithmRelated command display encrypt-cardfast-switch Esp encryption-algorithm Syntax ike-peer peer-name Undo ike-peer peer-name Ike-peer IPSec policy view/IPSec policy template viewUndo esp encryption-algorithm 2133 Related command ipsec policy-templateIpsec binding policy Syntax ipsec cpu-backup enable Undo ipsec cpu-backup enable Ipsec cpu-backup 2135 Ipsec policy interface view Syntax ipsec policy policy-nameseq-number isakmp manual Ipsec policy system view 2137 Ipsec policy isakmp templateIpsec policy-template Undo ipsec policy-template template-name seq-number Ipsec proposal Related command display ipsec policy-templateRelated command display ipsec proposal Example # Create an IPSec proposal named newprop1 Related command sa duration, display ipsec sa durationIpsec sa global-duration Ipsec session idle-time Undo pfs PfsUndo ipsec session idle-time Pfs dh-group1 dh-group2 dh-group5 dh-group14 Undo proposal proposal-name Example # Enable and configure PFS for IPSec policy policy1Related command ipsec proposal, ipsec policy system view Proposal Syntax reset encrypt-card fast-switch Reset encrypt-card fast-switchReset ipsec sa Syntax reset ipsec session tunnel-id integer Reset ipsec sessionRelated command display ipsec sa Syntax reset ipsec statistics Reset ipsec statisticsSa authentication-hex Related command display ipsec session 2145 Sa durationView IPSec policy view/IPSec policy template view Sa encryption-hex 2147 Sa spi Sa string-key 2149 Example # Configure IPSec policy policy1 to reference ACLSecurity acl Syntax security acl acl-number Undo security acl Syntax transform ah ah-esp esp Undo transform Example # Configure IPSec proposal prop1 to use AHTransform Tunnel local 2151 Tunnel remote Example # Set the remote address of the IPSec tunnel to Ike proposal, display ike proposal IKE Configuration Commands141 Undo dh Related command ike proposal, display ike proposalCertificate domain Dh group1 group2 group5 group14 Syntax display ike dpd dpd-name Related command ike dpdDisplay ike dpd Example # Specify 768-bit Diffie-Hellman for IKE proposal Syntax display ike peer peer-name Related command ike peer system viewDisplay ike peer Display ike proposal 2157 Example # Display the settings of IKE proposalsRelated command ike proposal, ike peer system view Display ike sa # Display detailed information about the current IKE SAs 2159 Encryption-algorithm 3des-cbc aes-cbc key-length des-cbc DpdUndo dpd Id-type Related command Id-type ExampleExchange-mode Syntax ike dpd dpd-name Undo ike dpd dpd-name Ike dpdIke local-name Example # Use the ID type of name in IKE negotiation 2163 Ike next-payload check disabledRelated command remote-name,id-typename Example # Configure the local gateway name as app Syntax ike peer peer-name Undo ike peer peer-name Related command display ike proposalIke peer system view Ike proposal Example # Set the keepalive interval to 200 seconds Ike sa keepalive-timer intervalIke sa keepalive-timer timeout Related command ike sa keepalive-timer timeout Interval-time Ike sa nat-keepalive-timer intervalRelated command ike sa keepalive-timer interval Example # Set the keepalive timeout to 20 seconds Local-address Local Undo peer Nat traversalSyntax nat traversal Undo nat traversal Peer multi-subnet single-subnet Syntax pre-shared-key key Undo pre-shared-key Related command authentication-algorithmonPre-shared-key Remote-address Remote-name Reset ike saRelated command id-typeip, local-address Related command id-type,ike local-name 2171 Related command display ike saExample # Clear the IPSec tunnel to Syntax sa duration seconds Undo sa duration Syntax time-out time-out Undo time-out Related command ike proposal and display ike proposalTime-out Public-key local create Example SSH2.0 Configuration Commands142 Display public-key local Specified or all public keys Display public-key peerDisplay public-key peer brief name publickey-name Brief Displays brief information about all public keys Syntax display sftp client source Related command sftp client sourceDisplay sftp client source # Display brief information about all public keys Syntax display ssh client source Related command ssh client sourceDisplay ssh client source Display ssh server 2177 Display ssh server-info# Display the session information of the SSH server Syntax display ssh server-info Example # Display information about all SSH users Related command ssh userDisplay ssh user-information Syntax display ssh user-information username Peer-public-key end Related command Public-key peer ExamplePeer-public-key end Public-key-code begin Public-key peer, public-key-code begin Public-key-code endPublic-key local create Public-key-code end # Create local DSA key pair Public-key local destroyPublic-key local destroy, display public-key local Example # Create local RSA key pair Public-key local create , public-key local destroy Related command public-key local createPublic-key local export rsa Public-key local export rsa openssh ssh1 ssh2 filename # Export the DSA local public key in OpenSSH format Public-key local export dsa# Display the RSA local public key in OpenSSH format Public-key local export dsa openssh ssh2 filename Syntax public-key peer keyname Undo public-key peer keyname Related command public-key-code begin, public-key-code endPublic-key peer # Display the DSA local public key in OpenSSH format 2185 Public-key peer import sshkeySftp Ipv6 ipv6-address Specifies a source IPv6 address Sftp client ipv6 sourceUndo sftp client ipv6 source Sftp ipv6 Related command Display sftp client source ExampleSftp client source Sysname sftp ipv6 Input Username Related command display ssh server Sftp server enableSftp server idle-timeout Syntax sftp server enable Undo sftp server enable Ssh client first-time enable Ssh client authentication server Undo ssh client ipv6 source To access the SSH serverSsh client ipv6 source Ssh client source Related command display ssh client source Ssh server authentication-retries Example # Enable the SSH server to work with SSH1.x clients Ssh server authentication-timeoutSsh server compatible-ssh1x enable By default, the authentication timeout period is 60 seconds Ssh server rekey-interval Ssh server enableSyntax ssh server enable Undo ssh server enable 2195 Ssh userUndo ssh user username Ssh2 Related command display ssh user-information 2197 Ssh2 ipv6 SSH2.0 Configuration Commands 2199 SSH2.0 Configuration Commands Syntax bye Sftp Configuration Commands143 Bye Syntax cdup CdupDelete Dir 2203 ExitGet Syntax exit Help 2205 MkdirPut Syntax quit PwdQuit Syntax pwd 2207 RemoveRename Rmdir Sftp-client rmdir temp1 Directory successfully removed View SSL server policy view SSL Configuration Commands144 Ciphersuite Close-mode wait Client-verify enableSyntax client-verify enable Undo client-verify enable Example # Set the SSL connection close mode to wait Syntax display ssl server-policy policy-nameall Display ssl client-policyDisplay ssl server-policy Syntax display ssl client-policy policy-nameall Syntax pki-domain domain-name Handshake timeoutSyntax handshake timeout time Undo handshake timeout Pki-domain 2213 Prefer-cipherUndo pki-domain Undo prefer-cipher Rsaaes128cbcsha Session cachesize size timeout timeUndo session cachesize timeout Session 2215 Ssl client-policySsl server-policy Ssl3.0 Specifies SSL Use the undo version command to restore the defaultVersion ssl3.0 tls1.0 SSL client policy view Syntax display standby flow Backup Center Configuration CommandsDisplay standby flow Following tables describe the meanings of each state Main and backup interfacesDisplay standby state Display standby state Syntax standby bandwidth size Undo standby bandwidth Backup states of the backup interfaceBackup flags Standby bandwidth Standby interface Related command standby interface 2221 Related commands standby trackStandby threshold Undo standby threshold Undo standby timer delay Standby timer delayRelated command standby interface and standby bandwidth 2223 Standby timer flow-checkStandby track Undo standby track Standby interface, track on Display vrrp IPV4-BASED Vrrp Configuration Commands Display vrrp statistics Description on the fields of the display vrrp commandVrrp vrid track interface command Vrrp vrid track command 2227 Example # Display the statistics about all standby groups Device are cleared Reset vrrp statisticsVrrp vrid authentication-mode 255 2229 Vrrp methodSyntax vrrp method real-mac virtual-mac Undo vrrp method Addresses of standby groups Vrrp ping-enableVrrp ping-enable Undo vrrp ping-enable Syntax vrrp un-check ttl Undo vrrp un-check ttl Default mode is immediate preemption without delayVrrp un-check ttl Vrrp vrid preempt-mode Vrrp vrid priority 2233 Vrrp vrid timer advertiseVrrp vrid track Vrrp vrid track interface 2235 Vrrp vrid virtual-ip # Add virtual IP address 10.10.10.11 to standby group IPv6 Vrrp Configuration Commands For IPV6147 Display vrrp ipv6 Display vrrp ipv6 statistics Vrrp ipv6 vrid track command 2239 Syntax vrrp ipv6 method real-mac virtual-mac Reset vrrp ipv6 statisticsVrrp ipv6 method Undo vrrp ipv6 method Vrrp ipv6 ping-enableVrrp ipv6 ping-enable Undo vrrp ipv6 ping-enable Vrrp ipv6 vrid preempt-mode Vrrp ipv6 vrid authentication-mode 2243 Vrrp ipv6 vrid priorityUndo vrrp ipv6 vrid virtual-router-idpriority Undo vrrp ipv6 vrid virtual-router-idtimer advertise Vrrp ipv6 vrid timer advertise 2245 Vrrp ipv6 vrid track Vrrp ipv6 vrid virtual-ip # Configure the virtual IPv6 address of standby group 1 as 148 Device Management Commands Part BootromBuzzer enable Syntax buzzer enable Undo buzzer enable Related command Boot-loader Display boot-loaderThis command is applicable on MSR 50 series routers only Display boot-loader slot slot-number Display cpu-usage task number offset verbose from-device Display cpu-usage 2251 Description on fields of the display boot-loader commandDisplay device Syntax display device cf-card usb slot slot-numberverbose Such as card, CF, USB, VCPM, VPM and DSP Cf-card Displays information of a compact Flash CFUsb Displays information of a universal serial bus USB Varies with devices Cpld Description on fields on the display device command2253 Display Display device manuinfoDisplay device manuinfo slot slot-number Information about the device Display environment # Display the temperature information of cardsDisplay environment Example # Display manufacturing information of a device Display license Display fanDisplay license Display fan fan-id Syntax display memory Display powerSyntax display power power-id Display memory Display schedule reboot Display reboot-typeDisplay schedule reboot Display reboot-type slot slot-number License register RebootOnly users at management level can execute this command Reboot slot slot-number Remove slot slot-number Reset unused porttagUse the remove command to remove a card Syntax reset unused porttag 2261 Schedule reboot atSyntax schedule reboot at hhmm date Undo schedule reboot Syntax schedule reboot delay hhmm mm Undo schedule reboot Schedule reboot delay 2263 Temperature-alarm enable Undo temperature-limit slot-number Temperature-limit Syntax data-fill string Undo data-fill NQA Client Configuration CommandsData-fill Syntax data-size size Undo data-size Data-sizeDescription any NQA test type view Syntax destination port port-number Undo destination port Destination ipDestination port Syntax destination ip ip-address Undo destination ip History Displays the history records of a test Syntax display nqa result history admin-nameoperation-tagDisplay nqa Result Displays the results of the last test 2269 Description on the fields of the display nqa result command Field Description Index History record number # Display the history records of tests Syntax frequency interval Undo frequency FilenameFrequency Syntax filename filename Undo filename Syntax history-records number Undo history-records History-records Undo http-version Http-versionNext-hop Http-version Nqa Nqa agent enableSyntax nqa agent enable Undo nqa agent enable Related command nqa server enable 2275 Example # Enable the NQA clientNqa agent max-concurrent Nqa schedule Undo operation Operation FTP test type viewOperation Http test type view Operation get put Undo operation interface Password FTP test type viewSyntax password password Undo password Operation interface Syntax probe count times Undo probe count Probe count 2279 Probe packet-intervalProbe packet-number Syntax probe timeout timeout Undo probe timeout Probe packet-timeoutProbe timeout 2281 Reaction Undo reaction trap probe-failure test-complete test-failure Reaction trapRoute-option bypass-route 2283 Related command source ipSource interface Undo source interface Syntax source ip ip-address Undo source ip Related command source interfaceSource ip Source port Syntax ttl value TosTtl Syntax tos value Type Undo url UrlUsername FTP test type view Syntax url url Syntax vpn-instance instance Undo vpn-instance Vpn-instance ICMP-echo test type view Syntax display nqa server status NQA Server Configuration Commands150 Display nqa server status Example # Enable the NQA server Nqa server enableSyntax nqa server enable Undo nqa server enable Related command nqa server tcp-connect,nqa server udp-echo 2291 Nqa server udp-echoUndo nqa server udp-echo ip-addressport-number Sysname nqa server udp-echo 169.254.10.2 Syntax display ip netstream cache Netstream Configuration CommandsDisplay ip netstream cache Exported NetStream UDP packets Ip netstream statistics commandDisplay ip netstream export Display ip netstream export Related command ip netstream aggregation EnableSyntax enable Undo enable Source-prefix Ip netstream aggregation 2297 Ip netstream export hostIp netstream export source Example # Enter NetStream AS aggregation view Ip netstream export version 2299 Ip netstream timeout activeRelated command ip netstream timeout inactive Ip netstream max-entry Reset ip netstream statistics Ip netstream timeout inactiveReset ip netstream statistics Related command ip netstream timeout active 152 NTP Configuration CommandsDisplay ntp-service sessions Syntax display ntp-service sessions verbose Example # View the NTP service status information Display ntp-service statusDisplay ntp-service status 2303 Display ntp-service traceSyntax display ntp-service trace Sure you have already created and configured this ACL Ntp-service accessUndo ntp-service access peer query server synchronization Protection. a more secure method is identity authentication # Enable NTP authentication Ntp-service authentication enableNtp-service authentication-keyid By default, NTP authentication is disabled Ntp-service broadcast-server Ntp-service broadcast-client 2307 Ntp-service in-interface disable Ntp-service multicast-client Ntp-service max-dynamic-sessions 2309 Ntp-service multicast-serverNtp-service refclock-master Undo ntp-service multicast-server ip-address Used as a reference clock Ntp-service reliable authentication-keyidNtp-service source-interface Undo ntp-service source-interface Ntp-service unicast-peer Public network Ntp-service unicast-serverVpn-instance-name in your command 2313 No NTP server is designated for the device by defaultDesignated for the device Interface and the NTP server coexist in this VPN NTP Configuration Commands Related command rmon alarm Rmon Configuration CommandsDisplay rmon alarm Syntax display rmon alarm entry-number Display rmon event Related command rmon eventExample # Display the configuration of Rmon event table Description on the fields of the display rmon event command 2317 Display rmon eventlogDisplay rmon history Syntax display rmon eventlog entry-number Related command rmon history Current-configuration and display this commands you cannot Display rmon prialarmSyntax display rmon prialarm entry-number Related command rmon prialarm Display rmon statistics Related command rmon statisticsWith the display current-configuration and display 2321 Rmon alarmUndo rmon alarm entry-number Rising alarm and falling alarm are alternate Table with the rmon event commandYou can create up to 60 alarm entries Rmon event Display rmon history You can create up to 100 alarm entriesRmon history Undo rmon history entry number 2325 Rmon prialarmUndo rmon prialarm entry-number # Remove private alarm entry Configurations the same and the creation failsYou can create up to 50 pri-alarm entries 2327 Rmon statistics Rmon Configuration Commands Display snmp-agent community Snmp Configuration CommandsDisplay snmp-agent local-switch fabricid 154 Descriptions on the fields of display snmp-agent community Display snmp-agent groupSyntax display snmp-agent group group-name 2331 Display snmp-agent mib-viewName of the specified MIB view Syntax display snmp-agent statistics Display snmp-agent statistics 2333 Display snmp-agent sys-infoDisplay snmp-agent sys-info contact location version Version Displays the version of the current Snmp agent Syntax display snmp-agent trap-list Related command snmp-agent trap enableDisplay snmp-agent trap-list # Display SNMPv3 information for the user aa Enable snmp trap updownSyntax enable snmp trap updown Undo enable snmp trap updown Display snmp-agent usm-user Undo snmp-agent Snmp-agentSnmp-agent Undo snmp-agent community community name Snmp-agent community Undo snmp-agent group v1 v2c group-name Undo snmp-agent group v3 group-name authentication privacyRelated command snmp-agentmib-view,snmp-agentusm-user Snmp-agent group Snmp-agent usm-user Snmp-agent local-switch fabricidSnmp-agent log Undo snmp-agent mib-view view-name Snmp-agent mib-view 2341 Related command snmp-agent groupSnmp-agent packet max-size Snmp-agent sys-info Snmp-agent target-host Related command Display snmp-agentsys-info 2343 Linkup warmstart * system voice vrrp authfailure newmaster Snmp-agent trap enable NMS, the device may not be able to resolute the messages Snmp-agent trap if-mib link extendedSnmp-agent trap if-mib link extended Undo snmp-agent trap if-mib link extended Snmp-agent trap queue-size Snmp-agent trap life Undo snmp-agent trap source Example # Configure the size of the Trap queue toSnmp-agent trap source Snmp-agent usm-user Parameter v1 SNMPv1 2349 Snmp Configuration Commands Copy File System Configuration Commands Syntax dir /all file-url Syntax delete /unreserved file-url 2353 ExecuteSyntax execute filename Syntax fixdisk device File promptFixdisk File prompt alert quiet 2355 FormatSyntax format device # create a subdirectory named mytest under test Syntax mount device MoreMount Syntax more file-url 2357 Related command Example UmountMove # Mount a CF card on a centralized device Example # Rename the file sample.txt as sample.bak Reset recycle-binSyntax reset recycle-bin /force Example # Move the file cf/test/sample.txt to cf/sample.txt 2359 UmountSyntax umount device Syntax undelete file-url Related command mountUndelete Example # Unmount a CF card on a device Syntax display saved-configuration by-linenum Configuration File Management CommandsBackup startup-configuration Display saved-configuration Configuration File Management Commands Display startup Reset saved-configurationRelated command startup saved-configuration Reset saved-configuration backup main Related command save, display saved-configuration Restore startup-configuration 2365 Syntax save file-name safely backup mainSave Startup saved-configuration 2367 Related command display startup Configuration File Management Commands Display ftp-server FTP Server Configuration CommandsRelated command ftp timeout and ftp update 157 Free ftp user Ftp server enableSyntax ftp server enable Undo ftp server Description on the fields of the display ftp-user command Syntax ftp update fast normal Undo ftp update Ftp timeoutFtp update Syntax ftp timeout minute Undo ftp timeout Sysname system-view Sysname ftp update normal Binary FTP Client Configuration Commands158 Ascii Syntax cd pathname Syntax debugging Undo debugging CloseDebugging Syntax close View FTP client view Parameter remotefile File name Description on the fields of the debugging command 2377 # View the content of aa.txtDisconnect Syntax disconnect Ftp Display ftp client configurationSyntax display ftp client configuration Related command ftp client source Undo ftp client source Ftp client sourceFtp client source Ftp ipv6 Related command display ftp client configuration 2381 Syntax lcd Lcd 2383 # View the content of file aa.txtOpen Open ipv6 Related command close 2385 PassiveSyntax passive Undo passive Remotehelp Parameter protocol-command FTP command 2387 # Display the help information for the user commandDescription on the fields of the remotehelp command Stat NlstSite Syst 2389 VerboseSyntax verbose Undo verbose FTP Client Configuration Commands Tftp-server acl Tftp Client Configuration CommandsDisplay tftp client configuration 159 # Associate IPv6 ACL 2001 with Tftp application in Ipv6 Tftp On the source interface, the transmission fails Related command tftp client sourceIP address configured on the device Tftp client source Tftp ipv6 Related command display tftp client configuration 2395 Tftp Client Configuration Commands Ping System Maintaining Commands160 Ping ipv6 2399 Tracert With IPv6 address Range 1 to 65535, defaulting to65535, in milliseconds. The default value is 5000 ms Tracert ipv6 System Maintaining Commands View User view Parameter all All debugging functions System Debugging Commands161 Undo debugging all module-name option Debugging Related command display debuggingDisplay debugging Clock summer-time one-off Basic Configuration Commands162 Clock datetime Basic Configuration Commands 2407 Clock summer-time repeating Clock timezone Display clock Command-privilegeCommand-privilege level level view view command Undo command-privilege view view command Display clipboard Configure-user countDescription Related command Display configure-user Syntax display clock Display configure-userSyntax display configure-user Display clock Exclude text Display current-configurationRelated command configure-user count 2413 Special characters in regular expression Version, display device, display current-configuration Display diagnostic-information# Display the configuration beginning with user Display diagnostic-information Display hotkey Display history-commandSyntax display history-command Display hotkey Syntax display this by-linenum Display this 2417 Display versionSyntax display version Header Header incoming legal login motd shell textUndo header incoming legal login motd shell Undo hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu Hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu commandCtrl+G corresponds to display current-configuration Hotkey # Display the configuration of hotkeys Syntax return Related command quitReturn Super Undo super password level user-level Super passwordRelated command super password Super password level user-level simple cipher password 2423 # Display the password for switching user-levelSysname Syntax sysname sysname Undo sysname Example # Enter system view from the current user view Related command quit, returnSystem-view Syntax system-view Example # Display information for channel Information Center Configuration CommandsDescription on the fields of the display channel command Display channel Syntax display info-center Display info-center 2427 Description on the fields of the display info-center command Meanings of characters in text Display logbufferRepresents information level, in the range 0 to Severity description 2429 Descriptions on the fields of the display logbuffer commandRest is omitted here Syntax display logfile buffer Display logbuffer summaryDisplay logfile buffer Display logbuffer summary level severity Syntax display logfile summary Support for the command varies with devicesExample # Display the contents of the log file buffer Display logfile summary Trap buffer, in the range 1 to 1,024 Display trapbufferInfo-center channel name Display trapbuffer size buffersize 2433 Info-center console channel Undo info-center logbuffer channel size Info-center enableSyntax info-center enable Undo info-center enable Info-center logbuffer 2435 Info-center logfile enableExample # Enable the log file feature Info-center logfile frequency Info-center logfile size-quota Info-center logfile switch-directorySyntax info-center logfile switch-directory dir-name 2437 Info-center loghost# Set the directory to save the log file to cf/test Undo info-center loghost host-ip Undo info-center loghost source Info-center loghost source 2439 Info-center monitor channelInfo-center snmp channel Undo info-center snmp channel Info-center source NMS Default output rules for different output directionsOutput Modules Enabled Direction Allowed Disabled Severity 2441 Info-center timestamp Info-center synchronous Undo info-center timestamp loghost Info-center timestamp loghostInfo-center timestamp loghost date no-year-date none Syntax logfile save Info-center trapbufferLogfile save Undo info-center trapbuffer channel size Terminal debugging Reset logbufferReset trapbuffer Syntax terminal logging Undo terminal logging Terminal loggingUndo terminal debugging Terminal trapping Terminal monitor Sysname terminal trapping Current terminal trapping is on Acl acl-number inbound User Interface Configuration CommandsAcl ipv6 acl-number inbound outbound Undo acl ipv6 acl-number inbound outbound Syntax activation-key character Undo activation-key Activation-key 2451 Auto-execute command Users log onto the device using the current user interface None Performs no authenticationPassword Performs local password authentication AAA, refer to AAA Configuration Commands on Undo databits DatabitsDatabits 5 6 7 Display user-interface Display history-commandHistory-commandmax-size 2455 # Display summary about all user interfaces All Displays information about users on all user interfaces Description on the fields of the display users commandDisplay users Display users all 2457 Syntax escape-key default character Undo escape-keyEscape-key Example # Define a as the escape key None 2459 Free user-interfaceSyntax free user-interface num1 aux console tty vty num2 View User interface view History-command max-size# Terminate the connection with user interface VTY Operating under the active user interface Password next time you enter the systemLock Lock Only, and cannot be applied to the Console port Syntax parity even mark none odd space Undo parity Example # Set the answering mode to auto-answerExample # Set the timeout interval to 50 seconds Parity Syntax protocol inbound all pad ssh telnet Example # Enable the VTYs 0 through 4 to support SSH onlyProtocol inbound Example # Perform odd parity check on the AUX interface Redirect disconnect Redirect enableRedirect enable Undo redirect enable Redirect listen-port port-number Related command telnet, display tcp statistics onRedirect listen-port Redirect refuse-negotiation Undo redirect return-deal from-telnet Redirect return-deal from-telnetRedirect return-deal from-telnet Redirect return-deal from-terminal Redirect timeout Syntax send all num1 aux console tty vty num2 Screen-lengthSend Syntax screen-length screen-length Undo screen-length Undo set authentication password Set authentication passwordSet authentication password cipher simple password Undo shell Related command authentication-modeShell Syntax shell Speed in user interface view Terminal type Stopbits Syntax user privilege level level Undo user privilege level User privilege level # Enter the user interface view of VTY 0 to # Enable user 1 to access level 3 commandsUser-interface User Interface Configuration Commands Display mac-address blackhole vlan vlan-id count MAC Address Table Management Configuration CommandsDisplay mac-address Ethernet interfaces Port Index Display mac-address aging-timeDisplay mac-address mac-learning Syntax display mac-address aging-time 2479 Mac-address Ethernet interface view Specified Vlan ID, in the range 1 to Related command display mac-addressMac-address system view Blackhole MAC address entries are dropped 2481 Mac-address mac-learning disable Mac-address max-mac-count Ethernet interface view Related command display mac-addressmac-learningExample # Disable global MAC address learning Undo mac-address timer aging Mac-address timerMac-address timer aging seconds no-aging MAC Address Table Management Configuration Commands Apply poe-profile POE Configuration Commands166 Display poe interface Module, and slot of the power sourcing equipment PSEDescription on fields of the display poe device command Display poe device 2487 # Display the state of all PoE interfaces Description on fields of the display poe interface command 2489 Display poe interface power Syntax display poe power-usage Display poe power-usage# Display the power information of all PoE interfaces 2491 Display poe pseSyntax display poe pse pse-id Description on fields of the display poe pse command Display poe-powerSyntax display poe-power 2493 Description on fields of the display poe-power command Number ranges from 1 to Existing PoE configuration files will be displayedDisplay poe-profile Display poe-profile index index name profile-name 2495 Description on fields of the display poe-profile command Syntax poe disconnect ac dc Undo poe disconnect Display poe-profile interfacePoe disconnect Syntax poe enable Undo poe enable Poe enable Poe legacy enable Poe enable pse 2499 Poe max-powerPoe max-power system view Syntax poe max-power max-power Undo poe max-power Undo poe mode Poe modeRelated command poe priority system view Poe mode signal spare Syntax poe pd-policy priority Undo poe pd-policy priority Poe pd-descriptionPoe pd-policy priority Syntax poe pd-description string Undo poe pd-description Syntax poe priority critical high low Undo poe priority Poe priority Undo poe priority pse pse-id Poe priority system viewPoe priority critical high low pse pse-id Poe pse-policy priority Poe updatePoe update full refresh filename pse pse-id Poe pse-policy priority Undo poe utilization-threshold pse pse-id Example # Set the power alarm threshold of PSE 2 to 90%Poe utilization-threshold Poe-profile Sysname system-view Sysname poe-profile abc Syntax oap connect slot slot-number OAP Module Configuration CommandsOap connect slot Syntax oap reboot slot slot-number Oap reboot slot Display acfp client-info Acfp Configuration CommandsAcfp enable 168 Interface-numberis the interface type and interface number Display acfp policy-infoClient-idis the Acfp client ID, in the range of 1 to Policy-index Policy index, in the range of 1 to 2511 Will display all the Acfp rule cache information Display acfp rule-cacheInterface type and interface number Interface-number is the interface type and interface number 2513 Display acfp rule-infoInterface number Client-id Acfp client ID, in the range of 1 to Establish # Display Acfp rule information in order of policy 2515 Display acfp server-infoSyntax display acfp server-info Type and interface number Reset acfp rule-cache Acsei server Acsei Server Configuration CommandsAcsei server enable Syntax acsei server enable Undo acsei server enable Syntax acsei timer monitor seconds Undo acsei timer monitor Acsei timer clock-syncAcsei timer monitor Display acsei client summary Acsei client rebootAcsei client close Syntax display acsei client info client-id Display acsei client info# Display the summary of all Acsei clients 2521 # Display information about all Acsei clients CPU information of the Acsei client 170 Acsei Client Configuration CommandsAcsei-client debug disable Acsei-client debug enable Syntax acsei-client debug show Chkconfig acseid offSyntax chkconfig acseid off Acsei-client debug show Syntax service acseid condrestart Chkconfig acseid onService acseid condrestart Syntax chkconfig acseid on # Load the Acsei client configuration file Service acseid reloadService acseid restart Service acseid reload Syntax service acseid status Service acseid startService acseid status Syntax service acseid start # Stop an Acsei client that is running Service acseid stopService acseid stop Any directory of the Linux system Display track Track Configuration CommandsDescription on the fields of the display track command 171 Track Configuration Commands Display ipx interface IPX Configuration Commands172 Syntax display ipx routing-table network Display ipx routing-table 2533 Display ipx routing-table verboseSyntax display ipx routing-table network verbose Display ipx routing-table protocol To 47 characters Display ipx service-tableInactive Displays inactive service information Display ipx routing-table statistics Syntax display ipx statistics # Display detailed IPX service informationDisplay ipx statistics SAP 2537 Configuration Ipx enableIpx enable node node Undo ipx enable Ipx encapsulation dot2 dot3 ethernet-2 snap Ipx netbios-propagationSyntax ipx netbios-propagation Undo ipx netbios-propagation Ipx encapsulation Ipx rip import-route static Ipx networkIpx rip import-route static Undo ipx network Syntax ipx rip mtu bytes Undo ipx rip mtu Example # Enable static route redistribution to RIPIpx rip mtu Ipx rip multiplier Example # Specify a RIP update interval of 30 seconds Ipx rip timer updateRelated command ipx rip timer update Related command ipx rip multiplier 2543 Ipx route load-balance-path Ipx route max-reserve-path Ipx sap disableSyntax ipx sap disable Undo ipx sap disable Ipx sap gns-load-balance Ipx sap gns-disable-replyIpx sap gns-disable-reply Undo ipx sap gns-disable-reply Syntax ipx sap mtu bytes Related command ipx sap gns-disable-replyIpx sap max-reserve-servers Ipx sap mtu 2547 Related command ipx sap timer updateIpx sap multiplier Undo ipx sap mtu Example # Specify the SAP updating interval as 300 seconds Ipx sap timer updateIpx service Related command ipx sap multiplier, ipx update-change-only Undo ipx split-horizon Ipx split-horizonIpx tick Ipx split-horizon Ping ipx Ipx update-change-onlySyntax ipx update-change-only Undo ipx update-change-only 2551 Reset ipx statisticsReset ipx routing-table statistics protocol Syntax reset ipx statistics # Clear IPX static route statistics Related command display ipx routing-table statisticsExample # Display IPX routing statistics 173 Voip Configuration Commands Undo area AreaArea-id Area custom europe north-america 2555 Related command match-template,address, and entityBusytone-t-th Syntax busytone-t-th time-threshold Undo busytone-t-th Syntax cid receive Undo cid receive Cid displayCid receive Syntax cid display Undo cid display View FXS/FXO voice subscriber line view Cid sendCid type Syntax cid send Undo cid send Undo cng-on Cng-onUndo cid type Syntax cng-on 2559 Related command line and vad-onCompression View POTS/VoIP/VoFR entity view Codec Bandwidth Voice quality Relationship between algorithms and bandwidth 726 r16 algorithm 711 algorithm A-law and µ-law723 r63 algorithm 723 r53 algorithm 726 r40 algorithm 726 r24 algorithm726 r32 algorithm Compression efficiency of IPHC+PPP header Algorithm Countries or regions with supported call progress tones Cptone country-typeSyntax cptone country-type locale Undo cptone country-type Regions are supported IEU 2565 Special-dial-tone waiting-tone amplitude Cptone tone-typeEffect on all voice interfaces of all cards on the device Special-dial-tone waiting-tone amplitude value G729r8 Default entity compression Related command compression Default entity payload-size Vad-on Default entity vad-onDefault entity vad-on Undo default entity vad-on Transmit gain Default subscriber-lineDelay hold Syntax delay rising milliseconds Undo delay rising Delay risingDelay send-dtmf Related command em-signal Syntax delay send-wink milliseconds Undo delay send-wink Delay send-wink 2573 Delay wink-holdDelay wink-rising Syntax delay wink-hold milliseconds Undo delay wink-hold Description voice entity view Delay start-dialSyntax delay start-dial seconds Undo delay start-dial View Voice view Description voice subscriber line viewDial-program Syntax dial-program Information table Display voice call-infoDisplay voice call-info brief mark tag verbose Range of 0 to Display voice cmc LGS 2579 Display voice default allSyntax display voice default all Description on fields of the display voice cmc command Description on fields of the display voice default command Display voice entity all mark entity-tag pots voip Display voice entity command ExampleDisplay voice entity Display voice ipp statistic Voip Configuration Commands 2583 Error Displays all the error statistics of IVA moduleDisplay voice iva statistic Call Displays the calling statistics in the IVA module Syntax display voice subscriber-line line-number Related command subscriber-lineDisplay voice subscriber-line = Busytone 2585 CNG Syntax dtmf amplitude value Undo dtmf amplitude Dscp mediaDtmf amplitude Syntax dscp media dscp-value Undo dscp media Undo dtmf time interval persist Dtmf sensitivity-levelDtmf time Dtmf time interval persist milliseconds Index Meaning Value range Remarks Dtmf thresholdMeaning of the index numbers 2589 Upper limit of the maximum To 4,999, with 2591 Echo-canceller Mix-proportion-ratio talk-threshold Echo-canceller parameterRelated command subscriber-lineand echo-canceller parameter Mix-proportion-ratio value talk-threshold value Em-phy-parm Em-signalRelated command echo-canceller Undo entity entity-numberall pots voip EntityEntity entity-number pots voip Fast-connect Related command Line ExampleRelated command outband, tunnel-on, and voip called-start Fast-connect Hookoff-mode Hookoff-mode delay bindExample # Enable fast connection for VoIP voice entity Syntax hookoff-mode delay immediate Undo hookoff-mode Syntax hookoff-time time Undo hookoff-time Private-lineand caller-permitcommands when executingHookoff-time Incoming calls Impedance Syntax match-template match-string Undo match-template LineMatch-template Undo line Such as 0-9. The formats like 0-A are illegal ThemIf you want to use and at the same time, you must use them Format . Other formats, such as and are illegal Nlp-on Command, but analog voice subscriber lines do notNlp-on E1 voice, T, #, and * are not supported currently Payload-size Related command Fast-connectand tunnel-on ExampleOutband 2603 Plc-modeSyntax plc-mode general specific Undo plc-mode Syntax receive gain value Undo receive gain Related command transmit gain and subscriber-lineReceive gain Match-template Reset voice cmc statisticRegister-number Related command display voice ipp statistic Reset voice ipp statisticReset voice iva statistic Related command display voice iva statistic Been used to identify nonstandard T38 fax packets Send-busytone enable time secondsUndo send-busytone enable time Send-busytone View Voice entity view Send-ringShutdown voice entity view Syntax send-ring Undo send-ring Undo silence-th-span Shutdown voice subscriber line viewSilence-th-span Example # Change the status of voice entity 4 to Down Undo slic-gain Slic-gainSubscriber-line Slic-gain 0 2611 Timer dial-intervalSyntax timer dial-interval seconds Undo timer dial-interval Syntax timer first-dial seconds Undo timer first-dial Timer first-dialTimer hookoff-interval Syntax timer ring-back seconds Undo timer ring-back Timer ring-backTimer wait-digit Related command hookoff-mode Syntax transmit gain value Undo transmit gain Related command receive gain and subscriber-lineTransmit gain View VoIP entity view Example # Enable the tunnel function for VoIP voice entityTunnel-on Syntax tunnel-on Undo tunnel-on Syntax vad-on Related command cng-onVad-on Undo type 2617 Vi-card busy-tone-detectUndo vi-card busy-tone-detect custom index Vi-card cptone-custom 2619 Vi-card rebootSyntax vi-card reboot slot-number Syntax voice-setup Voice-setupVoip called-tunnel enable Example # Reset the voice card of slot Fast-connect Voip timerVoip called-start Keyword Dscp value in binary Dscp value in decimal Vqa dscpCs7, or ef Dscp values Range 180 to By default, DSP buffered data is not monitoredVqa dsp-monitor buffer-time View Voice view Parameter Voip Configuration Commands Caller-permit Dial Plan Configuration Commands Syntax dial-prefix string Undo dial-prefix Related command match-templateonDial-prefix Syntax display voice number-substitute list-tag Related command match-templateon page 2599 and send-numberDisplay voice number-substitute Example # Specify 0 as a prefix Undo dot-match Related command number-substituteDot-match Dot-match end-only left-right right-left Undo max-call set-numberI all First-ruleMax-call in voice dial program view Syntax first-rule rule-number Undo first-rule Undo max-call Related command max-call in voice entity viewMax-call in voice entity view Number-match Related command max-call in voice dial program viewRelated command match-templateon page 2599 and terminator Example # Configure the longest-number match policy Number-substitute Related command rule and substitute voice dial program viewNumber-priority Syntax private-line string Undo private-line PriorityPrivate-line Undo priority Undo rule rule-tag all Rule 2635 Meanings of characters in the string argument Numbering plan Description Input number typeNumber type Description 2637 Input numbering planOutput numbering plan Undo select-rule rule-order Select-rule rule-order Integer Meaning Description Select-rule search-stopMeanings of integers 2639 Meanings of values Select-rule type-firstUndo select-rule type-first 2641 Select-stopSyntax select-stop Undo select-stop Send-number Related command dot-matchand match-templateon Undo substitute called calling Related command number-substituteand ruleSubstitute subscriber line view/voice entity view Substitute called calling list-number To Pstn are outgoing calls Substitute voice dial program viewAll Number-substitute and rule Example # Specify the pound sign # as the dial terminator Related command match-templateon page 2599 and timerTerminator Syntax terminator character Undo terminator Dial Plan Configuration Commands Undo ani E1 and T1 Configuration CommandsAni Ani all ka Ani-offset Answer enableRelated command cas, timer, reverse, and renew Syntax answer enable Undo answer enable Callmode segment terminal Related command re-answer enable and timer dl re-answerCallmode Cas Example # Enter the R2 CAS view of TS group Clear-forward-ack enable 2651 Related command modeDisplay voice subscriber line CNG/CED Dl-bits 2653 Default values of signals in R2 digital line signalingSignal Default rx-bits Abcd Default tx-bits Abcd Related command timer dtmf Dtmf enableRelated command seizure-ack enable and answer enable Syntax dtmf enable Undo dtmf enable 2655 Final-callednum enableSyntax final-callednum enable Undo final-callednum enable Related command register-valuedigital-end Syntax group-b enable Undo group-b enable Force-metering enableGroup-b enable Syntax force-metering enable Undo force-metering enable 2657 Related command register-valuereq-switch-groupb Mode Syntax mode zone-name default-standard Undo mode Syntax pcm a-law µ-law Undo pcm Related command register-valueand force-metering enableExample # Adopt Hongkong default R2 signaling Pcm Syntax pri-set timeslot-list range Undo pri-set Example # Adopt µ-law companding for signal quantizationPri-set 2661 Re-answer enableSyntax re-answer enable Undo re-answer enable Related command answer enable and timer dl re-answer Subscriber-busy subscriber-charge subscriber-idle Req-callednum-and-switchgroupa req-callingcategory reqChangeover to Group a signal value, in the range 1 to Demand-refused digit-end nullnum req-billingcategory 2663 Undo renew Related command group-b enableRenew Syntax renew Abcd Reverse Seizure-ack enableRelated command cas and reverse Related command cas and renew Timeslots Related command timer dl seizureSelect-mode View CAS view 2667 Sendring ringbusy enableRelated command cas and trunk-direction Related command timer ring Syntax special-character character number Signal-valueRelated command Subscriber line Example Special-character Undo special-character character number Different signal values Syntax tdm-clock internal line primary Undo tdm-clock Related command timeslot-setand pri-setTdm-clock Example # Enter the view of voice subscriber line 1/015 2671 Timer dlRelease-guard View R2 CAS view Syntax timer dtmf time Undo timer dtmf Timer dtmf Undo timer register-pulse persistence Timer register-pulse persistenceRelated command dtmf enable Timer register-pulse persistence time Undo timer register-complete group-b Timer register-complete group-bRelated command timer register-completegroup-b Timer register-complete group-b time Timeslot-set Timer ringTimer ring ringback ringbusy time Undo timer ring ringback ringbusy Trunk-direction Related command subscriber line and cas 2677 Related command cas and select-modeTs block open query reset timeslots timeslots-list CAS view Related command cas Default entity fax FAX Over IP Configuration Commands Syntax display voice fax statistics Display voice faxExample # Set the maximum fax rate to 9,600 bps globally 2681 Waitdpbegmodulatetimeout FaxvofrstandardswitchFAXVOFRFRF11SWITCH Waitdpbegdemodulatetimeout Undo fax baudrate Fax baudrate 2400 4800 9600 14400 disable voiceFax baudrate Undo fax ecm Fax ecmSyntax fax ecm 2685 Fax levelFax local-train threshold Syntax fax level level Undo fax level Syntax fax nsf-on Undo fax nsf-on Example # Configure the fax local training threshold toExample # Configure NSF for fax signal transmission Fax nsf-on Undo fax protocol Fax protocolFax protocol pcm g711alaw g711 μlaw Undo fax train-mode VoFR entities only support the PPP training modeFax train-mode Fax train-mode local ppp Voip h323-conf tcs-t38 Reset voice fax statisticsReset voice fax statistics Voip h323-conf tcs-t38 FAX Over IP Configuration Commands Syntax area-id string Undo area-id string Related command match-templateon page 2599, entity on177 Display voice gateway Gkid Gk-clientSyntax gk-client Undo gk-2nd-id Related command gk-idGk-2nd-id Example # Enter gatekeeper client view Gk-id Gk-security call enableRelated command area-id,gw-id,gk-2nd-id,gw-address,ras-on Syntax gk-security call enable Undo gk-security call enable Undo gk-security register-pwd Gk-security register-pwd cipher simple passwordGk-security register-pwd Gw-address Undo gw-id Gw-idUndo gw-address Syntax ras-on Related command gw-id,gw-address, and gk-idRas-on Voip h323-descriptor 323 Configuration Commands Syntax display voice sip call-statistics SIP Configuration Commands178 Display voice sip call-statistics TPT Message Syntax outband sip Undo outband Display voice sip register-stateOutband sip Display voice sip register-state SIP client view Default port number isProxy Undo proxy ipv4 Registrar ipv4 Register-enableRegister-enable off on Undo register-enable Syntax sip Reset voice sipSip Sip-comp SIP request messages Sip-comp agentUndo sip-comp callee from SIP client view View SIP client view Sip-comp serverSip-domain Undo sip-comp server 2707 Source-ipSyntax source-ip ip-address Undo source-ip SIP Configuration Commands 2709 Wildcard-register enableSyntax wildcard-register enable Undo wildcard-register Example # Enable fuzzy telephone number registration SIP Configuration Commands Undo address vofr-dynamic vofr-static Vofr Configuration Commands179 Address Cid select-mode Related command Trunk-idand address ExampleCall-mode Interface Dlci view Related command Vofr Example# Set the CID selection mode to min-poll on Dlci Display fr vofr-info Outband vofr Entity vofrOutband vofr Undo entity entity-number vofr Undo seq-number Seq-numberSeq-number Trunk-id Related command call-modeTimestamp 2717 Voice bandwidthVofr View Interface Dlci view Related command call-mode Hang up successfully in the FRF.11 trunk mode Vofr frf11-timerVofr frf11-timer time Undo vofr frf11-timer Vofr Configuration Commands Syntax aaa-client Voice Radius Configuration CommandsAaa-client Accounting View Voice AAA client view Related command acct-methodand accountingAccounting-did Syntax accounting-did Undo accounting-did Example # Set the accounting method to start-ack Related command accounting and accounting-did# Restore the default accounting method Acct-method Related command gw-access-numberand authorization AuthenticationAuthentication-did Syntax authentication Undo authentication 2725 AuthorizationRelated command authorization-did Syntax authorization Undo authorization Related command authentication-did Authorization-didRelated command gw-access-numberand authentication Syntax authorization-did Undo authorization-did 2727 Related command gw-access-numberCallednumber receive-method Syntax card-digit card-digit Undo card-digit Related command gw-access-numberand process-configCard-digit Cdr Example # Set the number of CDRs that can be saved to Related command display voice call-history-record# Set the alarm threshold for CDRs to 10% Undo cdr all buffer duration threshold Gw-access-number and aaa-client Display voice access-numberDisplay voice access-number 2731 Display voice call-history-record 2733 Related command cdrExample # Display call records by calling number Syntax display voice radius statistic Display voice radius statistic AAA=VORDS Related command reset voice radius statistic2735 VORDS=AAA CMC=VORDS Gw-access-number # Delete all access numbers Password-digit# Add the access number 179 and enter access number view # Delete the access number Process-config 2739 # Restore the default dialing process for the access number Undo redialtimes Redialtimes Display voice radius statistic Reset voice radius statisticGw-access-numberand process-config Selectlanguage Voice Radius Configuration Commands

3Com MSR 50 Multicast-domain switch-group-pool, Undo multicast-domain switch-group-pool, 1511

Models: MSR 50 MSR 30

1511

multicast-domain switch-group-pool

undo multicast-domain switch-group-pool