1681

<Sysname> display bgp vpnv4 all peer 1.1.1.1 verbose Peer: 1.1.1.1 Local: 2.2.2.2

Type: IBGP link

BGP version 4, remote router ID 1.1.1.1

BGP current state: Established, Up for 00h46m01s

BGP current event: RecvKeepalive
BGP last state: OpenConfirm
Port: Local - 1039	Remote - 179
Configured: Active Hold Time: 180 sec		Keepalive Time:60 sec
Received : Active Hold Time: 180 sec
Negotiated: Active Hold Time: 180 sec
Peer optional capabilities:
Peer support bgp multi-protocol extended

Peer support bgp route refresh capability

Address family IPv4 Unicast: advertised and received

Address family VPNv4: advertised and received

Received: Total 52 messages, Update messages 2

Sent: Total 65 messages, Update messages 5

Maximum allowed prefix number: 150000

Threshold: 75%

Minimum time between advertisement runs is 15 seconds

Optional capabilities:

Route refresh capability has been enabled

Connect-interface has been configured

Peer Preferred Value: 0

Routing policy configured:

No routing policy is configured

Table 450 Description on the fields of display bgp vpnv4 all peer verbose

Field	Description

Peer	IP address of the peer
Local	IP address of the local router
Type	BGP type
BGP version	Version of BGP that the peer runs
remote router ID	Router ID of the remote router
BGP current state	Current status of BGP
Up for	Duration since the peer is established
BGP current event	Current event of the peer
BGP last state	State that BGP was in before transitioning to the current status
Port	Local and remote BGP port numbers
Configured	Settings of the local timers, including the active hold interval and
	keepalive interval
Received	Received active hold interval
Negotiated	Negotiated active hold interval
Peer optional capabilities	Optional capabilities of the peer
Peer support bgp	The peer supports multiprotocol extension.
multi-protocol extended
Peer support bgp route	The peer supports route refresh capability.
refresh capability
Address family IPv4 Unicast	IPv4 unicast family capability
Address family VPNv4	IPv4 address group VPNv4 capability
Received	Total number of received messages and the number of received
	update messages

Page 1681

Image 1681

Contents

H3C MSR 20/30/50 Series Routers United States Government Legend 3Com Corporation Campus Drive Marlborough, MA USA Contents POS Interface Configuration Commands Adsl Interface Configuration CommandsGeneral Ethernet Interface Configuration Commands Fundamental CE1/PRI Interface Configuration Commands Fundamental Serial Interface Configuration Commands 14 E1-F Interface Configuration Commands Fundamental CT1/PRI Interface Configuration Commands Fundamental CE3 Interface Configuration Commands 15 T1-F Interface Configuration CommandsFundamental CT3 Interface Configuration Commands ATM Configuration Commands Isdn BRI Interface Configuration CommandsDCC Configuration Commands 340 Basic Dlsw Configuration Commands Frame Relay Configuration Commands Gvrp Configuration Commands Garp Configuration CommandsHdlc Configuration Commands Lapb and X.25 Configuration Commands 451 X25 pvc X25 queue-length 453 X25 receive-threshold 454 425 Display x25 hunt-group-info Display x25 map 426455 Link Aggregation Debugging Commands Link Aggregation Configuration CommandsModem Configuration Commands Port Mirroring Configuration Commands Pppoe Server Configuration Commands PPP Link Efficiency Mechanism Configuration CommandsPppoe Client Configuration Commands Bridging Configuration Commands PPP Debugging CommandsIsdn Configuration Commands Debugging ppp Mstp Configuration Commands PORT-BASEDVLAN Configuration Commands Vlan Configuration CommandsVoice Vlan Configuration Commands Port Isolation Configuration Commands ARP Configuration Commands Cpos Interface Configuration Commands ARP Source Suppression Configuration Commands Gratuitous ARP Configuration CommandsAuthorized ARP Configuration Commands Proxy ARP Configuration Commands Dhcp Client Configuration Commands Dhcp Relay Agent Configuration CommandsDhcp Snooping Configuration Commands Bootp Client Configuration Commands IP Accounting Configuration Commands DNS Configuration CommandsIP Addressing Configuration Commands IP Performance Configuration Commands UDP Helper Configuration Commands IP Unicast Policy Routing Configuration CommandsUrpf Configuration Commands Fast Forwarding Commands 840 Display tcp ipv6 status 842 NAT-PT Configuration CommandsDisplay natpt address-group 863 Display natpt aging-time 864 display natpt all Tunneling Configuration Commands Dual Stack Configuration Commands69 IPV6 Unicast Policy Routing Configuration Commands IP Routing Table Commands Terminal Access Configuration Commands BGP Configuration Commands 977 Ebgp-interface-sensitive981 Log-peer-change 983 Peer advertise-communityBGP/BGP-VPN instance view IS-IS Configuration Commands BGP Debugging Commands Ospf Configuration Commands IS-IS Debugging Commands 1117 1155 Snmp-agent trap enable ospf1128 1140 Routing Policy Common Configuration Commands RIP Configuration Commands1179 80 IPV6 Routing Policy Configuration Commands 79 IPV4 Routing Policy Configuration CommandsStatic Routing Configuration Commands 82 IPV6 BGP Configuration Commands 1243 12231246 84 IPV6 OSPFV3 Configuration Commands 83 IPV6 IS-IS Configuration Commands 86 IPV6 Static Routing Configuration Commands 85 IPV6 Ripng Configuration CommandsMulticast Routing and Forwarding Configuration Commands Delete ipv6 static-routes all 1325 ipv6 route-static Msdp Configuration Commands Igmp Configuration CommandsCache-sa-enable 1365 display msdp brief 1366 1376 PIM Configuration Commands 1422 14211429 93 IPV6 PIM Configuration Commands MLD Configuration Commands1451 1495 Multicast VPN Configuration CommandsDisplay multicast-domain vpn-instance share-group 1505 Mpls Basics Configuration Commands Mpls TE Configuration Commands Mpls rsvp-te reliability 1610 Mpls rsvp-te resvconfirm 1611 Mpls L3VPN Configuration Commands Mpls L2VPN Configuration Commands 1697 VAM Server Configuration Commands Ipsec Profile Configuration Commands VAM Client Configuration CommandsDvpn Tunnel Configuration Commands GRE Configuration Commands Traffic Shaping Configuration Commands Traffic Policing TP Configuration CommandsLine Rate Configuration Commands Defining Class Commands PQ Configuration Commands Fifo Queuing Configuration CommandsCQ Configuration Commands WFQ Configuration Commands Priority Mapping Table Configuration Commands QOS Token Configuration CommandsPort Priority Configuration Commands Port Priority Trust Mode Configuration Commands 126 802.1X Configuration Commands FR QOS Configuration CommandsAAA Configuration Commands access-limit Reset dar session 1927 Radius Configuration Commands1958 Packet Filter Firewall Configuration Commands Hwtacacs Configuration Commands MAC Authentication Configuration Commands Aspf Configuration Commands aging-timeNAT Configuration Commands PKI Configuration Commands RSH Configuration Commands rsh Portal Configuration CommandsCommon Configuration Commands 138 IPV4 ACL Configuration Commands Ipsec Configuration Commands 142 SSH2.0 Configuration Commands IKE Configuration Commands SSL Configuration Commands Sftp Configuration Commands bye 146 IPV4-BASEDVRRP Configuration Commands Backup Center Configuration CommandsVrrp Configuration Commands for IPV6 Device Management Commands Temperature-alarm enable 2263 Temperature-limit NQA Client Configuration Commands2262 2276 Netstream Configuration Commands NQA Server Configuration CommandsNTP Configuration Commands Rmon Configuration Commands File System Configuration Commands cd Snmp Configuration Commands FTP Server Configuration Commands Configuration File Management CommandsFTP Client Configuration Commands ascii Tftp Client Configuration Commands System Debugging Commands System Maintaining CommandsBasic Configuration Commands Information Center Configuration Commands 2460 User Interface Configuration Commands POE Configuration Commands MAC Address Table Management Configuration CommandsOAP Module Configuration Commands Acsei Server Configuration Commands Acfp Configuration CommandsAcsei Client Configuration Commands Track Configuration Commands 2551 Reset ipx routing-table statistics protocol Voip Configuration Commands address2546 Area 2554 area-id 2592 175 E1 and T1 Configuration Commands ani Dial Plan Configuration CommandsCaller-permit 2639 177 H.323 Configuration Commands FAX Over IP Configuration CommandsSIP Configuration Commands Voice Radius Configuration Commands aaa-client Vofr Configuration Commands2716 2734 Lists icon conventions that are used throughout this guide About this GuideLists text conventions that are used throughout this guide Text Conventions Documentation Related Area Ospf view 1108 area OSPFv3 view Alphabetical Listing of CommandsPage Page Rp IPv6 PIM view 1464 c-rp PIM view Page Display bgp vpnv4 vpn-instancerouting-table Page Display ipv6 policy-based-route statistics Page Page Page Page Page Fr compression frf9 385 fr compression iphc Page Igmp last-member-query-interval Ipv6 nd autoconfig managed-address-flag Page Page Page Mpls te resv-style 1631 mpls te retry 2308 Peer keep-all-routesBGP/BGP-VPN instance view Peer ebgp-max-hopBGP/BGP-VPN instance viewPeer allow-as-loopBGP/BGP-VPN instance view Peer preferred-valueBGP/BGP-VPN instance view Peer next-hop-localBGP/BGP-VPN instance viewPeer next-hop-invariableBGP-VPNv4 subaddress family view Peer public-as-onlyBGP/BGP-VPN instance view Pppoe-servermax-sessionsremote-mac Qos wred ip-precedence 1850 qos wred queue table Primary accounting Hwtacacs scheme view Reset aspf session 2007 reset atm interface 112 reset bgp Reset pim ipv6 control-message counters Page Page Statistics interval 1562 step for IPv4 2100 step for IPv6 Ssl client-policy 2215 ssl server-policyPage Page Page X29 timer inviteclear-time Page Display interface atm Public ATM and DSL Interface CommandsSyntax display interface atm interface-number Syntax reset atm interface atm interface-number Reset atm interfaceInterface atm Cable Configuration CommandsClock Code ami hdb3 CodeCode ami b8zs Undo code Display interface ima-group Differential-delaySyntax display interface ima-group group-interfacenumber 115 View ATM E1/T1 interface view Parameter Frame-formatATM direct mapping CRC4 ADM ESF ADM Ima ima-group Frame-lengthSyntax frame-length 32 64 128 Undo frame-length Syntax ima ima-group group-number Undo ima ima-group Example # Add the link of ATM E1 interface 5/0 to IMA group Ima-clockSyntax ima-clock ctc link-number number itc Undo ima-clock Ima-test Ima-standardIma-test link-number number pattern-id id Undo ima-test Interface ima-group By default, IMA group interface test is disabledLoopback Syntax loopback cell local payload remote Undo loopback Scramble Min-active-linksSyntax min-active-links number Undo min-active-links Syntax scramble Undo scramble Parameter None Syntax cable long short Undo cable Slave Sets the clock mode as slaveView ATM E3/T3 interface view Frame-format cbit-adm cbit-plcp m23-adm m23-plcp Frame-format g751-adm g751-plcp g832-adm Loopback cell local payload remote ATM E3/T3 Interface Configuration Commands Frame-format sdh sonet Loopback cell local remote 129 View ATM OC-3c interface view, STM-1 interface view ATM OC-3C/STM-1 Interface Configuration Commands Activate Shdsl Interface Configuration CommandsSyntax activate Undo activate View ATM G.SHDSL interface view Field Description Display dsl configuration Syntax display dsl status interface atm interface-number Display dsl status133 Gspn 135 Description on the fields of the display dsl status command Syntax display dsl version interface atm interface-number Display dsl versionITU G991.2 Annex A, ITU Shdsl annex Shdsl mode Shdsl psd Example # Set the operating mode of interface ATM 5/0 to COShdsl rate Syntax shdsl psd asymmetry symmetry Undo shdsl psd Kbps four-wire G.SHDSL interface rate is 4,624 kbps Single-pair interface rate to auto mode# Configure ATM 5/0 to operate in the auto-negotiation mode Use the undo shdsl snr-margincommand to restore the default Shdsl wire 2 4-auto-enhanced 4-enhanced 4-standard Shdsl wireUndo shdsl wire 141 Shdsl Interface Configuration Commands View ATM Adsl interface view Adsl Interface Configuration CommandsExample # Activate Adsl interface 2/0 Adsl tx-attenuation Adsl standardAdsl standard auto g9923 g9925 gdmt glite t1413 Undo adsl standard 145 Bootrom update file Display dsl configuration LS0US 147 Dslam FieldDescription Bdcm 149 Adsl Interface Configuration Commands Crc POS Interface Configuration CommandsSyntax crc 16 Undo crc Syntax display interface pos interface-number Display interface pos LCP opened, Ipcp opened, IP6CP opened 153 Display ipv6 interface pos Display ip interface posDisplay ip interface pos interface-number Syntax display ipv6 interface pos interface-number Flag Example # Set the SDH overhead byte J0 of POS1/0 interface Related command display interface pos# Set the framing format on interface POS 1/0 to SDH Loopback local remote Link-protocolLocal Internal loopback Remote External loopback That the state of the link layer protocol is reported up MtuInterfaces cannot be connected successfully Syntax mtu size Threshold Example # Enable payload scrambling on interface POS 1/0Syntax threshold sd sf value Undo threshold sd sf 159 Example # Set the SD threshold to 10e-4 for POS 1/0 Combo enable General Ethernet Interface Configuration CommandsRelated command display port combo and shutdown Description Special characters used in regular expressions Display brief interfaceCharacter Meaning Example # Display brief information of interfaces Related command interface163 Acronyms for different types of Interface Display interfacePvid Interface name Acronyms Field 165 Output queue Fifo queuing 167 Duplex Related command speedFlow-control Syntax duplex auto full half Undo duplex Can be represented as 1/0 InterfaceE1/0 Syntax loopback external internal Undo loopback Port link-mode Support for these two commands varies with device modelsPort link-mode bridge route Undo port link-mode Example # Configure Ethernet1/0 to work in bridge mode Reset counters interfaceView User view 171 Speed Shutdown 173 Related command duplex General Ethernet Interface Configuration Commands Broadcast-suppression Display port Display loopback-detectionSyntax display loopback-detection Display port hybrid trunk Display port-group manual all name port-group-name Display port-group manualExamples Group-member Flow-intervalSyntax flow-interval interval Undo flow-interval Undo group-member interface-list 179 Loopback-detection control enable Related command loopback-detection control enable Loopback-detection enableLoopback-detection interval-time View System view/Ethernet interface view Related command display loopback-detection Loopback-detection per-vlan enable181 Mdi Optical port of a Combo port does not support this commandMulticast-suppression Mdi across auto normal Port-group manual port-group-name aggregation agg-id Port-groupUndo port-group manual port-group-name Unicast-suppression Currently, these two commands are not supportedVirtual-cable-test Syntax virtual-cable-test 185 Page Example # Configure MTU for Ethernet1/0 to be 1,000 bytes Timer holdSyntax timer hold seconds Undo timer hold Configuration Commands for Ethernet Interfaces in Route Mode Async mode Fundamental Serial Interface Configuration CommandsSyntax async mode flow protocol Undo async mode Baudrate Undo baudrate Clock serial interface viewClock dteclk1 dteclk2 dteclk3 dteclk4 dteclkauto View Serial interface view 191 Dteclk1Clock selection option Description Country-code Code nrziSyntax code nrzi Undo code View Synchronous serial interface view Detect Example # Configure to adopt 32-bit CRCSyntax crc 16 32 none Undo crc Asynchronous serial interface detect dsr-dtr Syntax eliminate-pulse Undo eliminate-pulse Eliminate-pulseView Asynchronous serial interface view Invert receive-clock Idle-markSyntax idle-mark Undo idle-mark Syntax invert receive-clock Undo invert receive-clock Syntax invert transmit-clock Undo invert transmit-clock Invert transmit-clock Syntax loopback Undo loopback Mtu on serial interfaces197 Phy-mru Physical-modeSyntax physical-mode async sync Syntax phy-mru size Undo phy-mru Syntax reverse-rts Undo reverse-rts Reverse-rts199 Virtualbaudrate virtualbaudrate VirtualbaudrateUndo virtualbaudrate Baudrate Channel-set CE1/PRI interface view Fundamental CE1/PRI Interface Configuration Commands Clock Clock CE1/PRI interface view Controller e1 Code CEI/PRI interface viewController e1 number Crc 16 32 none Detect-aisSyntax detect-ais Undo detect-ais Display controller e1 Description on the fields of the commandSyntax display controller e1 interface-number 205 Undo error-diffusion restraint config Error-diffusion restraint config Error-diffusion restraint restart-channel Error-diffusion restraint enableBy default, error packets diffusion restraint is enabled Example # Enable error packets diffusion restraint Idlecode CE1/PRI interface view Frame-format CE1/PRI interface viewTwo types of line idle code are available 0x7E and 0xFF Itf number number type 7e ff Itf CE1/PRI interface viewUndo itf type number Pri-set CE1/PRI interface view Loopback CE1/PRI interface viewLoopback local payload remote Pri-set timeslot-list list Reset counters controller e1 interface-number Reset counters controller e1Command Display controller e1 interface-number command Using ce1 e1 Using CE1/PRI interface viewUndo using Alarm-threshold Fundamental CT1/PRI Interface Configuration CommandsLevel-2 Level-2 , level-3 , and level-4 Bert pattern 215 220 time minutes unframed Bert CT1/PRI interface viewUndo bert Ranges from 1 to 1,440 Channel-set CT1/PRI interface view Cable CT1/PRI interface view655ft View CT1/PRI interface view Clock CT1/PRI interface view Controller t1 Code CT1/PRI interface viewAmi Adopts AMI line code format # Set the line code format of the interface T1 2/0 to AMI Data-coding inverted normal Data-coding CT1/PRI interface viewUndo data-coding Syntax display controller t1 interface-number Display controller t1219 Clock or slave for the line clock 221 Error-diffusion restraint config Example # Enable error packet diffusion restraint By default, the function is disabled223 Error packet diffusion restraint function Support of this command varies with device modelFdl Set-number argument is a channel set number Idlecode CT1/PRI interface view Frame-format CT1/PRI interface viewFrame-format esf sf Loopback CT1/PRI interface view Itf CT1/PRI interface viewSyntax itf number number type 7e ff Undo itf number type Syntax loopback local payload remote # Enabled remote loopback on interface T1 2/0 Remote Enables the interface to perform remote loopbackPri-set CT1/PRI interface view Loopback on the CT1/PRI interface Reset counters controller t1 interface-number Reset counters controller t1For a CT1/PRI interface # Clear the controller counter for CT1/PRI interface T1 2/0 229 Sendloopcode Fundamental CT1/PRI Interface Configuration Commands Display fe1 E1-F Interface Configuration CommandsDisplay fe1 serial interface-number Fe1 clock Fe1 cableFe1 cable long short Undo fe1 cable Fe1 detect-ais Fe1 code Fe1 loopback Fe1 frame-format Fe1 timeslot-list Local Sets the interface in internal loopback modeUndo fe1 loopback Syntax fe1 timeslot-list list Undo fe1 timeslot-list Fe1 idlecode Related command fe1 unframedFe1 itf Syntax fe1 idlecode 7e ff Undo fe1 idlecode Fe1 unframed Fe1 unframedUndo fe1 unframed Related command fe1 timeslot-list Display ft1 T1-F Interface Configuration CommandsDisplay ft1 serial interface-number Description on the fields of the display ft1 serial command Bert statestopped, not completed 241 Ft1 bert pattern 215 220 time minutes unframed Ft1 bert T1-F interface viewUndo ft1 bert T1-F interface view Syntax ft1 cable long decibel short length Undo ft1 cable Ft1 cableView T1-F interface view 243 Ft1 code Ft1 clockFt1 clock master slave Undo ft1 clock Ft1 data-coding inverted normal Ft1 data-codingUndo ft1 data-coding Ft1 frame-format Ft1 fdl Ft1 itf Ft1 idlecodeFt1 idlecode 7e ff Undo ft1 idlecode Ft1 loopback Use the undo ft1 loopback command to restore the defaultFt1 loopback local payload remote Undo ft1 loopback Ft1 timeslot-list # Set T1-F interface Serial 2/0 in local loopback mode249 Undo ft1 alarm-threshold Ft1 alarm-thresholdOn the T1-F interface 251 Ft1 sendloopcode T1-F Interface Configuration Commands Bert CE3 Interface Fundamental CE3 Interface Configuration CommandsBert pattern 27 211 215 qrss time number unframed Controller e3 Clock CE3 interface viewDisplay controller e3 Example # Enter the view of interface E3 2/0 Syntax display controller e3 interface-number Display controller e3255 Fundamental CE3 Interface Configuration Commands 257 E1 bert E1 channel-set Related command e1 unframedE1 set clock Syntax e1 line-numberset clock master slave Undo e1 line-numberset clock E1 set frame-formatView CE3 interface view 259 E1 shutdown E1 set loopbackUndo e1 line-numbershutdown E1 unframed Related command e1 channel-setFe3 Undo e1 line-numberunframed Set the DSU mode or the subrate CE3 interface in FE3 mode viewUse the undo fe3 command to restore the default These two commands are only available in E3 mode National-bit Loopback CE3 interface viewNational-bit 0 Undo national-bit Related command controller e3 Using CE3 interface viewSyntax using ce3 e3 Undo using Example # Set the national bit to 0 on interface E3 2/0 Alarm CT3 interface view Fundamental CT3 Interface Configuration CommandsAlarm detect generate ais febe idle rai Undo alarm detect generate ais febe idle rai Bert CT3 interface view # Enable CT3 interface T3 2/0 to send AIS alarm signals Clock CT3 interface view Cable CT3 interface viewSyntax cable feet 267 Controller t3 Related command display controller t3Example # Enter the view of interface T3 2/0 None Adopts no CRC Syntax display controller t3 interface-number Display controller t3269 AIS 271 Configurable and default to line LOS, LOF, AIS, or RAI Feac CT3 interface view Ft3 Frame-format CT3 interface viewFrame-format c-bit m23 275 Mdl CT3 interface view Loopback CT3 interface view 277 # Set LIC to hello for CT3 interface T3 2/0 T1 alarm# Send path messages on CT3 interface T3 2/0 279 T1 bert T1 channel-set Related command t1 unframed 281 T1 sendloopcode T1 set frame-format T1 set clock T1 set fdl T1 set loopbackView CT3 interface view 283 T1 show T1 shutdown Description on the fields of the t1 show command285 T1 unframed Related command t1 channel-setUndo t1 line-numbershutdown Syntax t1 line-numberunframed undo t1 line-numberunframed Using ct3 t3 Using CT3 interface viewCt3 Sets the CT3 interface to operate in channelized mode T3 Sets the CT3 interface to operate in unchannelized mode Fundamental CT3 Interface Configuration Commands Loopback Isdn BRI interface view Isdn BRI Interface Configuration CommandsLoopback b1 b2 both Fixed Isdn interfaces on your router, if there is any Isdn BRI Interface Configuration Commands Related command atm-class ATM Configuration CommandsAtm class Atm-class Atm-link check Related command atm classSyntax atm-link check Undo atm-link check View ATM P2P sub-interface view Display atm class Related command Display atm interface ExampleDisplay atm class atm-class-name Syntax display atm interface atm interface-number Display atm interface 295 Display atm map-info VPI/VCI Display atm pvc-groupPVC-NAME State 297 Display atm pvc-info Syntax encapsulation aal5-encap Undo encapsulation EncapsulationIndex Example # Enter Atm1/0 interface Ip-precedence299 Map bridge Related command pvc-group,pvcView PVC view/ATM Class view Map ip # Configure an IP address 10.1.1.1/16 for the VE interface# Create PVC 1/102 on the ATM interface Atm2/0 Map ip inarp minutes broadcast Undo map ip inarp Syntax map ppp virtual-template vt-number Undo map ppp Map ppp # Create PVC 1/101 on interface Atm1/0 # Create a PPPoA map using the VT interface created303 Oam ais-rdi Undo oam frequency Oam frequency305 Pvc Oamping interface VCI range for each type of ATM interface Related command display atm pvc-info,pvc max-number307 Interface type Pvc-group Related command ip-precedence,pvcPvc max-number Syntax pvc max-number max-number Undo pvc max-number Undo pvp limit vpi Pvp limit Example # Set the traffic of VP with vpi 1 to 2M Service cbrInterface type Value range of output-pcr Service vbr-nrt Service ubrRelated command service vbr-nrt,service vbr-rt,service ubr Syntax service ubr output-pcr Related command service ubr, service vbr-rt, and service cbr Service vbr-rt # Bring up ATM 5/0 Parameters None313 Syntax transmit-priority value Undo transmit-priority Transmit-priority Related command dialer bundle-member DCC Configuration CommandsDialer bundle Dialer bundle-member Dialer callback-center Related command dialer bundle 317 Dialer call-in Related command interface dialer Related command dialer callback-centerDialer circular-group Dialer enable-circular Dialer enable-circularUndo dialer enable-circular Bundle-member command Related command dialer threshold Related command dialer circular-groupDialer flow-interval Dialer isdn-leased physical interface view Syntax dialer number dial-number Undo dialer number Dialer number321 Dialer priority Related command dialer routeDialer queue-length Syntax dialer priority priority Undo dialer priority 323 Dialer route Dialer threshold Related command dialer flow-interval Dialer timer autodial325 Dialer timer compete Dialer timer idle Dialer timer enableSyntax dialer timer enable seconds Undo dialer timer enable Syntax dialer timer idle seconds Undo dialer timer idle Dialer user Dialer timer wait-carrierSyntax dialer user username Undo dialer user Example # Add a remote username routerb Dialer-groupSyntax dialer-group group-number Undo dialer-group 329 Example # Add interface Serial 2/0 to dialer access group Related command dialer-ruleDialer-rule Undo dialer-rule group-number Display dialer Related command dialer-groupAny view Number Display interface dialer number Display interface dialerNumber Dialer interface number Information about all the dialer interfaces Syntax interface dialer number Undo interface dialer number Interface dialer333 Ppp callback ntstring Ppp callbackPpp callback client server Undo ppp callback client server Undo ppp callback ntstring Related command ppp callback335 DCC Configuration Commands Example # Configure Serial 1/0 to use Nrzi encoding Basic Dlsw Configuration CommandsDisplay dlsw circuits Syntax display dlsw circuits circuit-id verbose Display dlsw information local ip-address Display dlsw information # Display the local information about capabilities exchange Display dlsw remoteSyntax display dlsw remote ip-address 339 Display dlsw reachable-cache Display dlsw reachable-cacheInformation of DLSw # Display the reachability information of DLSw Display llc2 Description on the fields of the display llc2 commandSyntax display llc2 circuit circuit-id 341 Syntax dlsw enable Undo dlsw enable Dlsw enableDlsw bridge-set Dlsw ethernet-frame-filter # Enable DLSw343 Dlsw local Dlsw reachable # Allow the router to access SAP addresses 12345 Dlsw reachable-cache # Permit access to user-configured MAC addresses onlyDlsw remote Undo dlsw remote ip-address 347 Dlsw reverse Related command sdlc mac-map remoteDlsw max-transmission Syntax dlsw reverse mac-address Undo dlsw multicast Dlsw multicast349 Dlsw timer Syntax link-protocol sdlc Link-protocol sdlc351 Llc2 max-pdu Llc2 max-ackSyntax llc2 max-ack length Undo llc2 max-ack Syntax llc2 max-pdu length Undo llc2 max-pdu Llc2 max-transmission Llc2 max-send-queueSyntax llc2 max-send-queue length Undo llc2 max-send-queue 353 Llc2 receive-window Llc2 moduloLlc2 modulo 8 Undo llc2 modulo Llc2 timer ack-delay Llc2 timer ackSyntax llc2 timer ack mseconds Undo llc2 timer ack 355 Llc2 timer detect Llc2 timer busySyntax llc2 timer busy mseconds Undo llc2 timer busy Syntax llc2 timer detect mseconds Undo llc2 timer detect Syntax llc2 timer poll mseconds Undo llc2 timer poll Llc2 timer poll357 Reset dlsw circuits Llc2 timer rejectReset dlsw reachable-cache Syntax reset dlsw tcp ip-address Reset dlsw tcpDescription on the fields of the reset dlsw tcp command 359 Sdlc controller Syntax sdlc enable dlsw Undo sdlc enable dlsw Sdlc enable dlswSdlc mac-map local 361 Sdlc mac-map remote Sdlc max-send-queue Sdlc max-pduSyntax sdlc max-pdu number Undo sdlc max-pdu Syntax sdlc max-send-queue length Undo sdlc max-send-queue Sdlc modulo Sdlc max-transmissionView Synchronous serial interface view Specifies the modulus value to be Sdlc sap-map local Related command sdlc sap-map remote365 Sdlc sap-map remote Related command sdlc sap-map localSdlc simultaneous Syntax sdlc simultaneous Undo sdlc simultaneous Sdlc status primary secondary Sdlc statusUndo sdlc status primary secondary Sdlc timer lifetime Sdlc timer ackSyntax sdlc timer ack mseconds Undo sdlc timer ack Syntax sdlc timer poll mseconds Undo sdlc timer poll Sdlc timer pollSdlc window Syntax sdlc window length Undo sdlc window Undo sdlc xid sdlc-address Sdlc xid Annexg Frame Relay Configuration CommandsDisplay fr compress Annexg dce dte Related commands fr compression frf9 Display fr dlci-switch Display fr inarp-info Related command fr inarp ExampleDisplay fr interface # Display statistics about frame relay Inarp packets Range 0 to Display fr lmi-info# Display information about all frame relay interfaces Frame Display fr iphc Related command fr compression iphc375 Mappings or the one for the specified interface Display fr map-infoWhether dynamic address mapping operates normally Fr map ip , fr inarp 377 Display fr map-info pppofrDlci = 100, IP Inarp 1007 Display fr pvc-infoStatistics about data transmitted and received on them Fr dlci 379 Display fr statistics MTU Display interface mfr 381 Display mfr LID Description on the fields of the display mfr command Syntax display x25 template name Display x25 template383 Related command x25 template, x25-template Fr compression iphc Fr compression frf9Syntax fr compression frf9 Undo fr compression View Subinterface point-to-point view Undo fr compression iphc Fr dlciUndo fr dlci dlci-number Use the undo fr dlci command to cancel the configuration Fr dlci-switchUndo fr dlci-switch in-dlci Related command fr switching Syntax fr inarp ip dlci-number Undo fr inarp ip dlci-number Fr inarp Syntax fr interface-type dce dte nni Undo fr interface-type Fr interface-type389 Fr lmi n391dte Fr iphcTcp-include Fr map ip , fr compression iphc Syntax fr lmi n392dce n392-value Undo fr lmi n392dce Fr lmi n392dce391 Syntax fr lmi n392dte n392-value Undo fr lmi n392dte Fr lmi n392dte Fr lmi n393dte Fr lmi n393dceSyntax fr lmi n393dce n393-value Undo fr lmi n393dce Syntax fr lmi n393dte n393-value Undo fr lmi n393dte Syntax fr lmi t392dce t392-value Undo fr lmi t392dce Fr lmi t392dce Fr lmi type ansi nonstandard q933a bi-direction Fr lmi typeUndo fr lmi type Fr map ip Related command interface virtual-templateon Fr switchUndo fr switch name Fr map ppp Syntax fr switching Undo fr switching Fr switching Interface serial Interface mfr399 Link-protocol fr ietf nonstandard Link-protocol fr Mfr bundle-name Link-protocol fr mfrSyntax link-protocol fr mfr interface-number Syntax mfr bundle-name name Undo mfr bundle-name Mfr fragment-size Mfr fragmentSyntax mfr fragment Undo mfr fragment Syntax mfr fragment-size bytes Undo mfr fragment-size Syntax mfr link-name name Undo mfr link-name name Mfr link-name403 Mfr stateup-respond-addlink Mfr retrySyntax mfr retry number Undo mfr retry Syntax mfr timer ack seconds Undo mfr timer ack Mfr timer ackRelated command mfr timer hello, mfr retry 405 Syntax mfr timer hello seconds Undo mfr timer hello Mfr timer helloMfr window-size Syntax mfr window-size number Undo mfr window-size View Frame relay switching view Reset fr inarpSyntax reset fr inarp Related command fr inarp Related command fr lmi t392dce Reset fr pvcExample # Clear all the frame relay dynamic address maps X25 template X25-templateSyntax x25-template name Undo x25-template name Syntax x25 template name Undo x25 template name Frame Relay Configuration Commands Display garp timer Garp Configuration CommandsSyntax display garp timer interface interface-list Display garp statistics Related command garp timer, garp timer leaveall Garp timerExample # Display Garp timers on port Ethernet 1/0 View Ethernet interface view, port group view Related command display garp timer Garp timer leaveallDependencies of Garp timers Timer Lower limit Upper limit Reset garp statistics interface interface-list Reset garp statisticsDisplay gvrp statistics Display gvrp statistics Gvrp Configuration CommandsSyntax display gvrp statistics interface interface-list Display gvrp status Related command display gvrp statusGvrp Syntax gvrp Gvrp registration fixed forbidden normal Gvrp registrationUndo gvrp registration Display garp statistics Gvrp Configuration Commands Timer hold Hdlc Configuration CommandsTimer hold seconds Link-protocol hdlc Hdlc Configuration Commands Channel Lapb and X.25 Configuration CommandsX25 hunt-group Lapb and X.25 Configuration Commands 423 Description on the fields of the display interface commandLapb DCE Display x25 alias-policy Display x25 cug Related command x25 alias-policy ExampleDisplay x25 hunt-group-info Display x25 cug local-cug local-cug-number network-cug Display x25 map Related command x25 hunt-groupSyntax display x25 map Display x25 pad Description on the fields of the display x25 map commandExample # Display the X.25 address mapping table Syntax display x25 pad pad-id Display x25 switch-table svc Display x25 switch-table pvcSyntax display x25 switch-table pvc Syntax display x25 switch-table svc dynamic static Example # Display X.25 SVC static switching table Related command x25 switch svcDisplay x25 vc Syntax display x25 vc lci Data 0/0 Interrupt 0/0 431 Description on the fields of the display x25 vc commandSVC Display x25 xot Display x25 x2t switch-table Syntax lapb max-frame n1-value Undo lapb max-frame Lapb max-frame433 Difference between N1 Lapb modulo Related command lapb window-sizeLapb retry Parameter 8 Modulo Undo lapb timer t1 t2 t3 Lapb timerLapb window-size Syntax lapb window-size k-valueundo lapb window-size Lapb modulo Link-protocol lapbLink-protocol lapb dce dte ip multi-protocol Link-protocol x25 dce dte ietf nonstandard Pad Reset Reset xot Syntax reset lapb statistics Reset lapb statisticsTranslate ip Undo translate ip ip-addressport port-number Undo translate x25 x.121-address TranslateParameter x.121-address X.121 address 441 X25 alias-policy Description on the user facility option X25 call-facility Related command x25 map, x25 modulo X25 cug-service443 Option Description Window-size Related command x25 local-cug X25 default-protocol 445 X25 hunt-group X25 ignore calling-address X25 ignore called-address 447 X25 local-cug X25 map Related command x25 call-facility,x25 cug-serviceUndo x25 map ip compressedtcp protocol-address 449 Send-delay delay-timeOption Description Broadcast Protocols such as Routing Information Protocol Syntax x25 modulo 8 Undo x25 modulo X25 modulo # Set the modulo on the X.25 interface Serial 2/0 to X25 packet-sizeUndo x25 packet-size 451 Undo x25 pvc pvc-number X25 pvcDescription on PVC attribute option Syntax x25 queue-length queue-length Undo x25 queue-length X25 queue-length453 X25 receive-threshold Related command x25 window-size X25 response calling-address X25 response called-address455 X25 reverse-charge-accept Related command x25 map Related command x25 call-facility,x25 map X25 switch pvcUndo x25 switch pvc pvc-number1 X25 roa-list Lapb and X.25 Configuration Commands 121 mode matching rules X25 switch svc459 Number SVC route number Input rules of X.121 address mode matching stringCharacters Input rules 461 X25 switch svc hunt-group Related command display x25 switch-table svc X25 switch svc xot Syntax x25 switching Undo x25 switching X25 switching X25 timer idle X25 timer holdExample # Enable X.25 switching function Syntax x25 timer hold minutes Undo x25 timer hold Syntax x25 timer tx0 seconds Undo x25 timer tx0 X25 timer tx0Related command x25 timer tx1, x25 timer tx2, x25 timer tx3 465 X25 timer tx2 X25 timer tx1Syntax x25 timer tx1 seconds Undo x25 timer tx1 Related command x25 timer tx0, x25 timer tx2, x25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx3 X25 timer tx3Syntax x25 timer tx3 seconds Undo x25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx2 X25 vc-range X25 vc-per-mapSyntax x25 vc-per-map count Undo x25 vc-per-map Undo x25 window-size X25 window-size469 X25 xot pvc X25 x121-addressSyntax x25 x121-address x.121-address Undo x25 x121-address Undo x25 pvc pvc-number1 Related command display x25 vc, x25 switchingXOT channel parameter option 471 X29 timer inviteclear-time Display lacp system-id Link Aggregation Configuration CommandsDisplay link-aggregation interface Syntax display lacp system-id Link Aggregation Configuration Commands Syntax display link-aggregation summary Display link-aggregation summary475 Example # Display the link aggregation group summary Display link-aggregation verboseSyntax display link-aggregation verbose agg-id AL ID 477 Lacp port-priority Link-aggregation group description Lacp system-priorityExample # Assign Lacp priority 64 to a port 479 Related command display link-aggregation verbose Link-aggregation group modeRelated command display link-aggregation summary Port link-aggregation group Related command Display link-aggregation verbose Example Reset lacp statisticsPort-group aggregation Port-group aggregation agg-id Example # Clear statistics about Lacp on all ports Related command display link-aggregation interface View User view Default Level 1 Monitor level Link Aggregation Debugging CommandsDebugging lacp packet Link Aggregation Debugging Commands Length of the Terminator field in the protocol packet is Device sent an Lacp protocol packet through Ethernet 1/1485 Device received an Lacp protocol packet through Ethernet 1/1 487 Debugging lacp state Syntax debugging link-aggregation error Debugging link-aggregation error Debugging link-aggregation event ErrorSyntax debugging link-aggregation event 489 # Remove aggregation group Aggregation group 10 existed. It contained Ethernet 1/1Aggregation group 10 was removed Operation key of port Ethernet 1/1 Key 1 was removed Modem Modem Configuration CommandsModem auto-answer Syntax modem timer answer time Undo modem timer answer Modem timer answer Sendat Sendat command can issue only one AT command at a timeWith caution under the guidance of technicians Specifies the communication standard to be adopted Example # Send dialing command to call number Service modem-callbackSyntax service modem-callback 495 Example # Enable the callback function Undo service modem-callback Display mirroring-group Port Mirroring Configuration CommandsMirroring-group Syntax display mirroring-group groupid local Undo mirroring-group groupid local Mirroring-group mirroring-port 499 Mirroring-group monitor-port # Add POS 5/1 to local port mirroring group Mirroring-port # Add Cpos 6/1 to local port mirroring group Monitor-port501 Port Mirroring Configuration Commands Display interface mp-group PPP and MP Configuration 31 CommandsSyntax display interface mp-group mp-number Display interface virtual-template Related command interface virtual-templateSyntax display interface virtual-template number Example # View the information about VT Display ppp mp Description on the fields of the display ppp mp commandLink-protocol ppp , ppp mp 505 For description on the output fields, refer to Table Display virtual-access 507 Interface mp-group Ip address ppp-negotiate Interface virtual-template Ppp account-statistics enable Ppp account-statistics enableUndo ppp account-statistics enable Link-protocol ppp Ppp authentication-mode chap pap call-in domain isp-name Ppp authentication-modeUndo ppp authentication-mode Chap, pap Authentication modes. Use either mode Related command ppp authentication-modechap Ppp chap passwordPpp chap user Syntax ppp chap user username Ppp ipcp dns Related command ppp authentication-modeUndo ppp chap user Ppp ipcp dns request Ppp ipcp dns admit-anySyntax ppp ipcp dns admit-any Undo ppp ipcp dns admit-any Syntax ppp ipcp dns request Undo ppp ipcp dns request Ppp ipcp remote-address forced Related command remote address Undo ppp lqc Ppp lqc515 Ppp mp binding-mode Ppp mpSyntax ppp mp Undo ppp mp Ppp mp max-bind Related command Ppp mp user ExamplePpp mp max-bind max-bind-num Undo ppp mp max-bind Ppp mp min-bind Related command Ppp mp ExamplePpp mp min-bind min-bind-num Undo ppp mp min-bind Ppp mp min-fragment Related command dialer threshold onPpp mp min-fragment size Undo ppp mp min-fragment Ppp mp user Ppp mp mp-groupSyntax ppp mp mp-group number Undo ppp mp Example # Add interface Serial 3/0 to MP-group Ppp mp virtual-template Related command ppp mp and ppp mp max-bindSyntax ppp mp virtual-template number Undo ppp mp 521 Related command local-useron page 1940, password on Ppp timer negotiateSyntax ppp timer negotiate seconds Undo ppp timer negotiate Ppp pap local-user Undo remote address Remote address523 Timer hold Display ppp compression iphc rtp PPP Link Efficiency Mechanism Configuration CommandsDisplay ppp compression iphc tcp Ip tcp vjcompress Display ppp compression stac-lzsSyntax ip tcp vjcompress Undo ip tcp vjcompress 527 Ppp compression iphc Ppp compression iphc rtp-connections Ppp compression stac-lzs Ppp compression iphc tcp-connections529 Syntax ppp mp lfi Undo ppp mp lfi Ppp mp lfi Reset ppp compression iphc Ppp mp lfi delay-per-frag531 PPP Link Efficiency Mechanism Configuration Commands Display pppoe-server session Pppoe Server Configuration CommandsDisplay pppoe-server session all packet Pppoe-server log-information off Pppoe-server bind Pppoe-server max-sessions remote-mac Pppoe-server max-sessions local-mac535 Pppoe-server max-sessions total Reset pppoe-serverPppoe-server max-sessions total number Undo pppoe-server max-sessions total 537 Pppoe Server Configuration Commands Display pppoe-client session Pppoe Client Configuration Commands Pppoe-client dial-bundle-number Related command Reset pppoe-client Reset pppoe-clientReset pppoe-client all dial-bundle-number number Related command pppoe-client Sysname reset pppoe-client all Debugging ppp PPP Debugging Commands Description on the fields of the debugging ppp event command 545 Description on the fields of the debugging ppp ipcp command LCP moved from the initial state to the starting state Description on the fields of the debugging ppp ipcp commandLCP moved from the starting state to the reqsent state 547 PPP Debugging Commands Bridge bridge-set enable Bridging Configuration CommandsSyntax bridge bridge-setenable Undo bridge bridge-setenable Bridge aging-time Example # Enable bridge set Bridge enable# Enable IP bridging on bridge set Syntax bridge enable Undo bridge enable Bridge learning Example # Enable bridgingBridge mac-address 551 Bridge routing Syntax bridge routing-enable Undo bridge routing-enable Bridge routing-enableBridge-set Syntax bridge-set bridge-set Undo bridge-set bridge-set Display bridge address-table Syntax display bridge information bridge-set bridge-set Display bridge information555 Dynamic S--STATIC Display bridge traffic Syntax display interface bridge-template interface-number Display interface bridge-template557 Syntax fr map bridge dlci broadcast Undo fr map bridge dlci Fr map bridgeUP/DOWN Bridge routing-enable Related command display fr map-infoonInterface bridge-template Parameters Mac-address bridge-template interface view Related command interface bridge-templateMap bridge-group Syntax mac-address mac-address Undo mac-address Reset bridge traffic Reset bridge address-table561 X25 map bridge x121-address x.121-address broadcast X25 map bridgeUndo x25 map bridge x121-address x.121-address Display x25 map on Dialer isdn-leased Isdn BRI interface view Isdn Configuration CommandsDialer isdn-leased 128k number Undo dialer isdn-leased 128k number Display isdn call-info Display isdn active-channel 565 Example # Display the current state of Isdn interface 2/0 Display isdn call-record 567 Display isdn parameters Isdn Display isdn spidKbri Kpri 569 Isdn bch-local-manage Channels in ascending order by default Bch-local-manage command on the user sideIsdn bch-select-way Isdn caller-number Isdn check-called-number Isdn callingUndo isdn calling Undo isdn check-called-number check-index Syntax isdn check-time date-time Undo isdn check-time Isdn check-time Isdn ignore connect-ack Isdn crlengthUndo isdn crlength Syntax isdn ignore connect-ack Isdn ignore hlc Settings must be the same as those on the exchangeUndo isdn ignore connect-ack Isdn ignore hlc Voice calls placed on the BRI interface 1/0 Isdn ignore llcIsdn ignore llc Undo isdn ignore llc Isdn ignore sending-complete ConfiguredIsdn ignore sending-complete incoming outgoing Undo isdn ignore sending-complete incoming outgoing Undo isdn L3-timer all timer-name Isdn L3-timerDescription of Q931 timers Value range Default Timer-name Seconds Isdn number-property Isdn link-modeSyntax isdn link-mode p2p Undo isdn link-mode View Isdn BRI interface 579 Types and code schemes of Isdn numbersProtocol Field Bit value Definition Type Code scheme Qsig NTT 581 Set the type and code scheme of Isdn numbers Calls Isdn overlap-sending 583 Isdn pri-slipwnd-size Isdn protocol-type Isdn protocol-modeSyntax isdn protocol-type protocol Undo isdn protocol-type Example # Apply Isdn Etsi on interface BRI 1/0 Isdn q921-permanentSyntax isdn q921-permanent Undo isdn q921-permanent View Isdn BRI interface view Isdn spid autotrigger Isdn send-restartSyntax isdn send-restart Undo isdn send-restart Syntax isdn spid autotrigger Syntax isdn spid timer seconds Undo isdn spid timer Isdn spid timerIsdn spid nit Syntax isdn spid nit Undo isdn spid nit Isdn spid service audio data speech Isdn spid serviceUndo isdn spid service Isdn spid1 Isdn spid resendSyntax isdn spid resend times Undo isdn spid resend Syntax isdn spid1 spid LDN Undo isdn spid1 Isdn spid2Syntax isdn spid2 spid LDN Undo isdn spid2 This command applies only on NI-compliant BRI interfaces Configuration of the Isdn calling commandSpid String of 1 to 20 digits LDN Local dialing number, a string of 1 to 30 digits Syntax isdn two-tei Isdn two-tei Undo isdn two-tei Permanent-activeView BRI interface view Syntax permanent-active Undo permanent-active Syntax power-source Undo power-source Power-source 595 # Bring up BRI 2/0 Isdn Configuration Commands Active region-configuration Mstp Configuration CommandsCheck region-configuration Syntax active region-configuration Port number Display stpBrief Displays brief information Information 599 Related commands reset stp Display stp abnormal-port Display stp abnormal-portAbnormally blocked ports Root guard action Display stp history Display stp down-portSyntax display stp down-port Syntax display stp instance instance-id history Syntax display stp region-configuration Display stp region-configuration Description on the fields of the display stp root command Related commands stp region-configurationDisplay stp root Syntax display stp root Model Display stp tcSent Tree instance, in port name order Region-name InstanceExamples # Map Vlan 2 to MST instance Syntax region-name name Undo region-name Reset stp interface interface-list Reset stpDisplay stp Revision-level Syntax stp enable disable Undo stpStp Syntax revision-level level Undo revision-level Examples # Enable the Mstp feature globally Related commands stp mode# Disable Mstp on port Ethernet 1/1 Stp bpdu-protection Stp compliance Stp bridge-diameter Stp config-digest-snooping Stp cost Or undo stp edged-port enable command to non-edge port Stp edged-port enable disableStp edged-port Undo stp edged-port Stp loop-protection Examples # Configure port Ethernet 1/1 as a non-edge portStp max-hops Syntax stp loop-protection Undo stp loop-protection Syntax stp mcheck Stp mcheck Stp no-agreement-check Stp modeStp mcheck , stp Stp pathcost-standard Examples # Enable No Agreement Check on Ethernet 1/1View System view Parameters 802.1D-1998 617 Stp point-to-point Stp port-log 619 Stp port priority Stp instance instance-id priority priority Stp priorityUndo stp instance instance-id priority Stp root primary Stp region-configuration Stp instance instance-id root secondary Stp root secondary Stp root-protection Syntax stp tc-protection enable Stp tc-protection disableStp tc-protection Syntax stp root-protection Undo stp root-protection Stp tc-protection threshold Stp timer forward-delay Syntax stp timer hello centi-seconds Undo stp timer hello Stp timer hello625 Stp timer max-age Syntax stp timer-factor number Undo stp timer-factor Stp timer-factor627 Vlan-mapping modulo Stp transmit-limitSyntax vlan-mapping modulo modulo 629 Examples # Map VLANs to MSTIs as per the modulo value Mstp Configuration Commands Display interface vlan-interface Vlan Configuration CommandsSyntax display interface vlan-interface vlan-interface-id Vlan interfaces will be displayed Vlan-interface-id Vlan interface ID# Display the information of VLAN-interface Display vlan Related command vlanExample # Display Vlan 2 information # Display Vlan 3 information Description on the fields of the display vlan command Related command display interface vlan-interfaceInterface vlan-interface Example # Create Vlan interface Ip address Related command display ip interface on635 View Vlan interface view Vlan Example # Enter Vlan 2 view Related command display vlan# Create Vlan 4 through Vlan 637 Vlan Configuration Commands Port access vlan PORT-BASED Vlan Configuration CommandsSyntax port access vlan vlan-id Undo port access vlan Port Port hybrid pvid vlan Related command port link-typeSyntax port hybrid pvid vlan vlan-id Undo port hybrid pvid 641 Port hybrid vlan Port trunk permit vlan Port link-type Syntax port trunk pvid vlan vlan-id Undo port trunk pvid Port trunk pvid vlan643 Related command port link-type Voice Vlan Configuration Commands Syntax voice vlan vlan-idenable Voice vlan enable ExampleDisplay voice vlan state Voice vlan Related command display voice vlan state Undo voice vlan enableVoice vlan aging Syntax voice vlan aging minutes Undo voice vlan aging Syntax voice vlan enable Undo voice vlan enable Voice vlan enableVoice vlan mac-address Range of 1 to 30 characters Ffff-f000-0000Be a broadcast, multicast or address of all 0s or all fs Display voice vlan oui Example Voice vlan security enable Voice vlan mode autoSyntax voice vlan mode auto Undo voice vlan mode auto 651 Example # Disable the security mode of the voice Vlan Voice Vlan Configuration Commands Port-isolate enable Port Isolation Configuration CommandsSyntax port-isolate enable Undo port-isolate enable Display port-isolate group Port Isolation Configuration Commands Standby routing-group Dynamic Route Backup Configuration CommandsStandby routing-rule Standby timer routing-disable Broadcast-limit link Logical Interface Configuration CommandsDisplay interface loopback Syntax display interface loopback number Example # View the status of Loopback Related command interface loopbackSyntax display interface mfr mfr-number Example # View the state information about MFR Related command interface mfr659 LMI Dlci Example # View the state information of MP-group Related command interface mp-group Display interface null Related command interface nullDisplay interface virtual-ethernet Syntax display interface null Example # View the state information about VE Related command interface virtual-ethernetExample # View the state information about VT 663 Description of the fields of the display mfr command Interface, state of the link layer, and the name 665 Interface ethernet Interface loopback Related command display interface loopbackExample # Create Loopback Example # Create MFR Interface nullExample # Create MP-group Interface null Interface virtual-ethernet Related command display interface nullExample # Enter Null 0 interface view 669 Logical Interface Configuration Commands Controller cpos Cpos Interface Configuration CommandsSystem view Display controller cpos cpos-number Display controller cpos Possible error types This table, FRED, COFA, and SEF are alarm errors AERRs673 Some information about T1 channels is omitted Display controller cpos e1Syntax display controller cpos cpos-numbere1 e1-number Syntax display controller cpos cpos-numbert1 t1-number Display controller cpos t1675 VC-3 677 Example # Bundle timeslots on E1 channel E1 set clock Example # Enable external payload loopback on E1 channel Related command display controller cpos e1679 Syntax e1 e1-numberunframed undo e1 e1-numberunframed Syntax e1 e1-numbershutdown undo e1 e1-numbershutdown Display controller cpos Undo flag j0 j1 c2Syntax frame-format sdh sonet undo frame-format Use the undo loopback command to remove a loopback Multiplex mode# Enable external loopback on interface Cpos 1/0 Syntax multiplex mode au-3 au-4 undo multiplex mode Example # In SDH mode, multiplex AUG to AU-3 Related command frame-format683 Example # Bundle timeslots on T1 channel Example # Shut down Cpos physical interface 1/0 685 Example # Enable external loopback on T1 channel Related command display controller cpos t1Syntax t1 t1-numbershutdown Undo t1 t1-numbershutdown 687 Syntax t1 t1-numberunframed Undo t1 t1-numberunframed Cpos Interface Configuration Commands Arp check enable ARP Configuration CommandsSyntax arp check enable Undo arp check enable Arp max-learning-num Arp static Related command reset arp, display arp Arp timer agingRelated command display arp timer aging Display arp Description on the fields of the display arp command Related command arp static, reset arp# Display the number of all ARP entries Arp static , and reset arp Example Display arp timer agingDisplay arp timer aging Arp timer aging Related command arp static and reset arp Naturemask-arp enableSyntax naturemask-arp enable Undo naturemask-arp enable Display arp vpn-instance Specified by the argument interface-type interface-number Reset arpArp static and display arp ARP Configuration Commands Gratuitous-arp-sending enable Gratuitous ARP Configuration CommandsGratuitous-arp-learning enable Gratuitous-arp-sending enable Sysname system-view Sysname gratuitous-arp-learning enable Arp source-suppression enable ARP Source Suppression Configuration CommandsArp source-suppression limit Display arp source-suppression Display arp source-suppression Related command display arp source-suppressionSyntax display arp source-suppression Description on fields of display arp source-suppression Arp authorized enable Authorized ARP Configuration CommandsSyntax arp authorized enable Undo arp authorized enable Arp authorized time-out Authorized ARP Configuration Commands Proxy-arp enable Proxy ARP Configuration CommandsLocal-proxy-arp enable Related command display proxy-arp Proxy-arp enable Related command display local-proxy-arpLocal-proxy-arp enable Display proxy-arp Dhcp Server Configuration Commands Dhcp enable Bootfile-nameSyntax bootfile-name bootfile-name Undo bootfile-name Syntax dhcp enable Undo dhcp enable Dhcp server detect Dhcp select server global-poolSyntax dhcp server detect Undo dhcp server detect 707 Dhcp server ip-pool Dhcp server forbidden-ip Related command dhcp enable Dhcp server ping timeoutDhcp server ping packets Example # Create the Dhcp address pool identified by Dhcp update arp Dhcp server relay information enableSyntax dhcp update arp Undo dhcp update arp Display dhcp server conflict Reset dhcp server conflictDisplay dhcp server expired Display dhcp server conflict all ip ip-address Display dhcp server forbidden-ip Display dhcp server free-ipDisplay dhcp server free-ip Syntax display dhcp server forbidden-ip Display dhcp server ip-in-use Reset dhcp server ip-in-useBinding information of all address pools is displayed Information of Dhcp address pools or an IP address Display dhcp server statistics Reset dhcp server statisticsSyntax display dhcp server statistics Example # Display the statistics on the Dhcp server Display dhcp server tree all pool pool-name Display dhcp server treeInformation of Dhcp address pools 715 Undo dns-list ip-addressall Dns-list Domain-name Related command dhcp server ip-poolExpired Gateway-list Related command dhcp server ip-pooland netbios-type Netbios-typeNbns-list 719 Network Related command dhcp server ip-pooland nbns-listUndo network Undo option code Option721 Reset dhcp server ip-in-use Reset dhcp server conflictReset dhcp server statistics Static-bind client-identifier Related command display dhcp server statisticsExample # Clear the statistics of the Dhcp server 723 Static-bind ip-address Tftp-server domain-name Static-bind mac-address725 Undo voice-config as-ip fail-over ncp-ip voice-vlan Voice-configTftp-server ip-address View Dhcp address pool view 727 Dhcp Server Configuration Commands Dhcp Snooping cannot be configured on the Dhcp relay agent Dhcp Relay Agent Configuration CommandsSyntax dhcp relay address-check disable enable Dhcp relay address-check Dhcp relay information format Dhcp relay information enable Dhcp relay information strategy drop keep replace Dhcp relay information strategyUndo dhcp relay information strategy Dhcp relay security static Dhcp relay release ipSyntax dhcp relay release ip client-ip Undo dhcp relay security ip-address all dynamic static Dhcp relay security tracker Related command display dhcp relay security733 Dhcp relay server-group Dhcp relay server-detectDhcp relay server-detect Undo dhcp relay server-detect Dhcp relay server-select Related command display dhcp relay server-group735 Dhcp select relay Dhcp update arpDhcp select relay Undo dhcp select relay Display dhcp relay security Display dhcp relayServer group that a specified interface corresponds to Groups correlated to an interface or all interfaces Display dhcp relay security tracker Display dhcp relay security statisticsDisplay dhcp relay security statistics Information about bindings of Dhcp relay agents Display dhcp relay statistics Display dhcp relay server-groupInterval is 10 seconds Syntax display dhcp relay server-group group-idall Server Client Reset dhcp relay statistics server-group group-id Reset dhcp relay statisticsWhich to remove statistics from the relay agent Display dhcp relay statistics Dhcp Relay Agent Configuration Commands Dhcp Client Configuration Commands Ip address dhcp-alloc Description on fields of the display dhcp client command 745 Dhcp Client Configuration Commands Related command display dhcp-snooping Dhcp Snooping Configuration CommandsDhcp-snooping Dhcp-snooping trust Display dhcp-snooping Related command display dhcp-snooping trustDisplay dhcp-snooping trust Dhcp-snooping Trusted ports Related command dhcp-snooping trust Example# Display information about trusted ports 749 Dhcp Snooping Configuration Commands Bootp client Bootp Client Configuration CommandsDisplay information about Bootp clients on all interfaces Including sub-interfaces and Vlan interfaces Syntax ip address bootp-alloc Undo ip address bootp-alloc Ip address bootp-allocRelated command display bootp client Description on fields of the display bootp client command Debugging dhcp server all error event packet Dhcp Debugging CommandsUndo debugging dhcp server all error event packet Debugging dhcp server Dhcp ACK Dhcp NAK DHCPmessagetype DHCP-DISCOVER packet received Checking for an expired lease755 DHCP-REQUEST message received Checking whether the IP address 22.0.0.2 is in use Sending a DHCP-ACK message Debugging dhcp relay Sysname Terminal debugging 759 Undo debugging dhcp client all error event packet Debugging dhcp client all error event packetDebugging dhcp client Then broadcast it 761 State of the Dhcp client is changed from Halt to Init Head 763 ARP message sent Dhcp client starts address conflict detection using ARP Display dns domain DNS Configuration CommandsDisplay dns dynamic-host Dns domain Example Syntax display dns proxy table Display dns proxy tableTTL Display dns server Related command dns serverDisplay ip host Syntax display dns server dynamic Related command display dns domain Dns proxy enableSyntax dns proxy enable Undo dns proxy enable Dns domain Dns server Dns resolveSyntax dns resolve Undo dns resolve Syntax dns server ip-address Undo dns server ip-address Related command display dns server Reset dns dynamic-hostRelated command display ip host Syntax reset dns dynamic-host 771 Related command display dns dynamic-host DNS Configuration Commands Display ip count IP Accounting Configuration CommandsDisplay ip count inbound-packets outbound-packets exterior Firewall-denied interior Syntax ip count enable Undo ip count enable Ip count enableDescription on fields of the display ip count rule command Display ip count rule Ip count exterior-threshold Example # Enable IP accountingIp count firewall-denied 775 Ip count inbound-packets Example # Count incoming IP packets on Ethernet1/0 Ip count interior-threshold# Specify not to count incoming IP packets on Ethernet1/0 777 Ip count rule Ip count outbound-packets Reset ip count Ip count timeoutSyntax ip count timeout minutes Undo ip count timeout Syntax reset ip count all exterior firewall interior Exterior Clears the statistics from the exterior table All Clears all statisticsInterior Clears the statistics from the interior table # Clear the statistics of all IP packets Display ip interface IP Addressing Configuration Commands Description on fields of the display ip interface command Display ip interface brief Related command display ip interfaceExample # Display brief information about Ethernet 1/0 783 Displayed 785 Ip address unnumbered IP Addressing Configuration Commands Display fib IP Performance Configuration Commands # Display FIB information passing ACL Description on the fields of the display fib command# Display FIB information passing the IP prefix list abc0 Display fib statistics Display fib ip-addressFor description about the above output, refer to Table Syntax display fib statistics Syntax display icmp statistics Display icmp statisticsExample # Display Icmp statistics 100 Display ip socket3072 # Display all socket information Display ip statistics Description on the fields of the display ip socket commandSyntax display ip statistics Example # Display statistics of IP packets Display tcp statisticsSyntax display tcp statistics 793 Example # Display statistics of TCP traffic Related command display tcp status and reset tcp statistics 795 Display tcp status Related command reset udp statisticsDisplay udp statistics Display tcp status Ip forward-broadcast acl acl-number Ip forward-broadcastUndo ip forward-broadcast Ip ttl-expires enable Ip redirects enable Reset ip statistics Ip unreachables enableReset tcp statistics Tcp anti-naptha enable Reset udp statisticsRelated command display tcp statistics Syntax reset udp statistics Tcp state Tcp mss Related command tcp anti-naptha enable Tcp syn-cookie enableThis support for this command varies with devices Syntax tcp syn-cookie enable Undo tcp syn-cookie enable Tcp timer fin-timeout Tcp timer check-stateExample # Enable the SYN Cookie feature 803 Related command tcp timer syn-timeoutand tcp window Tcp timer syn-timeoutRelated command tcp timer fin-timeoutand tcp window Syntax tcp window window-size Undo tcp window Tcp window805 IP Performance Configuration Commands Apply default output-interface IP Unicast Policy Routing Configuration CommandsApply ip-address default next-hop View policy-based-route view Apply ip-address next-hop Parameters ip-address IP address of the default next hopUndo apply ip-address next-hop ip-address ip-address Examples # Set the next hop to 1.1.1.1 for matched packets Apply ip-precedenceIP precedences and the corresponding keywords 809 Display ip policy-based-route Apply output-interfaceSyntax display ip policy-based-route 811 Display ip policy-based-route setup Display ip policy-based-route statistics Local Displays statistics of enabled system policy routingInterface-number Routing statistics Display policy-based-route Related commands if-matchpacket-lengthIf-match acl Syntax display policy-based-route policy-name If-match packet-length Related commands if-match aclIp local policy-based-route Related commands ip local policy-based-route Related commands policy-based-routeIp policy-based-route Policy-based-route Related commands if-match acl and if-matchpacket-length Reset policy-based-route statisticsSyntax reset policy-based-route statistics policy-name 817 IP Unicast Policy Routing Configuration Commands Reset udp-helper packet UDP Helper Configuration CommandsReset udp-helper packet Display udp-helper server Syntax udp-helper enable Undo udp-helper enable Udp-helper enableUdp-helper port Udp-helper server Related command display udp-helper server821 UDP Helper Configuration Commands Ip urpf loose strict allow-default-route acl acl-number Urpf Configuration CommandsIp urpf Undo ip urpf Urpf Configuration Commands Display ip fast-forwarding cache Fast Forwarding CommandsIp fast-forwarding Display ip fast-forwarding cache Fast Forwarding Commands Syntax reset ip fast-forwarding cache Reset ip fast-forwarding cache827 Fast Forwarding Commands Display dns ipv6 dynamic-host IPV6 Basics Configuration CommandsDisplay dns ipv6 server Syntax display dns ipv6 dynamic-host Example # Display IPv6 DNS server information Display ipv6 fibSyntax display ipv6 fib ipv6-address Display ipv6 fibcache Description on fields of the display ipv6 fib commandDisplay ipv6 host Syntax display ipv6 fibcache Display ipv6 interface 833 Shutdown command Display ipv6 neighbors Static vlan vlan-id count Display ipv6 neighbors count Display ipv6 pathmtu Description on fields of the display ipv6 pathmtu commandDisplay ipv6 socket Syntax display ipv6 pathmtu ipv6-addressall dynamic static Display ipv6 statistics Description on fields of the display ipv6 socket commandSyntax display ipv6 statistics 837 Description on fields of the display ipv6 statistics command 839 Display tcp ipv6 statistics Display tcp ipv6 statisticsStatistics # Display the statistics of IPv6 TCP connections 841 Syntax display tcp ipv6 status Display tcp ipv6 status Syntax display udp ipv6 statistics Display udp ipv6 statistics843 TCP6CB Ipv6 Dns server ipv6Syntax ipv6 Undo ipv6 Ipv6 address auto link-local Ipv6 address845 Ipv6 address link-local Ipv6 address eui-64 Ipv6 fib-loadbalance-type hash-based Ipv6 fibcacheSyntax ipv6 fibcache Undo ipv6 fibcache 847 Ipv6 host Ipv6 icmp-error Ipv6 mtu Ipv6 icmpv6 multicast-echo-reply enableSyntax ipv6 mtu mtu-size Undo ipv6 mtu 849 Ipv6 nd autoconfig other-flag Ipv6 nd autoconfig managed-address-flagIpv6 nd autoconfig managed-address-flag Undo ipv6 nd autoconfig managed-address-flag Ipv6 nd hop-limit Ipv6 nd dad attemptsSyntax ipv6 nd dad attempts value Undo ipv6 nd dad attempts Syntax ipv6 nd hop-limit value Undo ipv6 nd hop-limit Ipv6 nd nud reachable-time Ipv6 nd ns retrans-timer Syntax ipv6 nd ra halt Undo ipv6 nd ra halt Ipv6 nd ra haltOn a router # Suppress RA messages on Ethernet1/0 853 Ipv6 nd ra prefix Ipv6 nd ra intervalUndo ipv6 nd ra interval Undo ipv6 nd ra prefix ipv6-prefix 855 Ipv6 nd ra router-lifetime Ipv6 neighbor Ipv6 pathmtu Ipv6 neighbors max-learning-numUndo ipv6 pathmtu ipv6-address 857 Related command display ipv6 pathmtu Reset dns ipv6 dynamic-hostSyntax reset dns ipv6 dynamic-host Ipv6 pathmtu age Reset ipv6 neighbors Reset ipv6 fibcacheReset ipv6 pathmtu Reset tcp ipv6 statistics Reset ipv6 statisticsReset udp ipv6 statistics ICMPv6 packets Tcp ipv6 timer syn-timeout Tcp ipv6 timer fin-timeoutExample # Clear the statistics of all UDP packets 861 Syntax tcp ipv6 window size Undo tcp ipv6 window Tcp ipv6 window Display natpt address-group NAT-PT Configuration CommandsDisplay natpt address-mapping Display natpt address-group Syntax display natpt aging-time Display natpt aging-time Display natpt all Example # Display all NAT-PT configuration informationDisplay natpt all 865 Syntax display natpt frag-sessions Display natpt frag-sessions Display natpt statistics Display natpt sessionSyntax display natpt session all icmp tcp udp Display natpt statistics Undo natpt address-group group-number Natpt address-group Natpt aging-time Syntax natpt enable Undo natpt enable Natpt enableNatpt max-session Syntax natpt max-session max-number Undo natpt max-session Natpt prefix Example # Configure a NAT-PT prefixUndo natpt prefix natpt-prefix 871 Natpt turn-off traffic-class Natpt turn-off tosNatpt turn-off tos Undo natpt turn-off tos Natpt v4bound static Natpt v4bound dynamic873 Natpt v6bound dynamic Syntax reset natpt dynamic-mappings Reset natpt dynamic-mappingsNatpt v6bound static Undo natpt v6bound static ipv6-addressipv4-address Reset natpt statistics Reset natpt statistics# Clear all NAT-PT statistics information Dual Stack Configuration Commands Automatically create a link-local address for an interface Ipv6 address auto link-localAutomatically created link-local address Ethernet interface view 879 Example # Configure a link-local address on Ethernet 1/1 Dual Stack Configuration Commands Related command interface tunnel and source Tunneling Configuration CommandsDestination Undo destination Syntax display interface tunnel number Display interface tunnelExample # Display information of the interface tunnel Syntax display ipv6 interface tunnel number Display ipv6 interface tunnel883 Interface tunnel Encapsulation-limitSyntax encapsulation-limit number Undo encapsulation-limit Syntax interface tunnel number Example # Create the interface tunnel Undo interface tunnel number885 Source Related command interface tunnel and destinationUndo source Ipv4-ipv6 Tunnel-protocolUndo tunnel-protocol Tunneling Configuration Commands Apply destination-based-forwarding IPV6 Unicast Policy Routing Configuration CommandsView IPv6 policy-based-route view Apply ipv6-address default next-hop Apply ipv6-precedence Apply ipv6-address next-hopExample # Set a next hop of 11 for matched IPv6 packets Preferences and the corresponding keywords Apply output-interface Syntax display ipv6 config policy-based-route policy-name Display ipv6 config policy-based-routeDisplay ipv6 policy-based-route Display ipv6 policy-based-route Local Displays system policy routing information Display ipv6 policy-based-route setup Display ipv6 policy-based-route statistics Related command if-matchpacket-lengthIf-match acl6 Syntax if-match acl6 acl6-number Undo if-match acl6 Ipv6 local policy-based-route Related command if-match acl6Example # Permit the packets matching ACL Ipv6 policy-based-route interface view Related command ipv6 local policy-based-routeIpv6 policy-based-route system view 897 IPV6 Unicast Policy Routing Configuration Commands Auto-close Terminal Access Configuration CommandsAuto-link Syntax auto-close time Undo auto-close Syntax bind vpn-instance vpn-name Undo bind vpn-instance Bind vpn-instance Data read block Data protect router-unixView Terminal template view Syntax data read block Undo data read block Syntax data send delay milliseconds Undo data send delay Data send delayDisplay rta 903 # Display brief information about TTY TTY Description on the fields of the display rta all command # Display all the information about terminal access# Display statistics about terminal 905 Driverbuf save # Display terminal access statisticsDriverbuf size Syntax driverbuf save Undo driverbuf save Syntax idle-timeout seconds Undo idle-timeout Idle-timeoutUndo driverbuf size 907 Menu hotkey Related command print information and print menuMenu screencode Syntax menu hotkey ascii-code&1-3 Undo menu hotkey Syntax print connection-info Undo print connection-info Print connection-info909 Related command print connection-infoand print menu Related command print informationPrint information Print menu Redrawkey Print languagePrint language chinese english Terminal template view Reset rta statistics Reset rta connectionReset rta statistics terminal-number Related command display rta ResetkeyUndo resetkey Rta bind Rta rtc-server listen-port Syntax rta server enable Undo rta server enable Rta server enableRta source-ip Syntax rta source-ip ip-address Undo rta source-ip Rta terminal Rta templateHiding TCP connections Syntax sendbuf bufsize size Undo sendbuf bufsize Sendbuf bufsize917 Tcp Sendbuf thresholdSyntax sendbuf threshold value Undo sendbuf threshold Testkey # Disable TCP delay# Set the TCP send buffer size to 512 bytes Undo testkey Access Update changed-configUpdate changed-config Values are used for the hotkeys of flow control Vty hotkey Vty descriptionUndo vty vty-numberdescription 921 Vty password Vty rtc-server remote Vty rtc-client remote923 Vty screencode Related command menu screencodeUndo vty vty-numberscreencode Vty tty remote Vty telnet remoteExample # Set the screen code for VTY 1 to E!9Q 925 Vty-switch threshold Vty-switch prioritySyntax vty-switch priority Undo vty-switch priority Syntax vty-switch threshold times 927 Undo vty-switch threshold Terminal Access Configuration Commands Bandwidth-based-sharing IP Routing Table CommandsDisplay ip routing-table Syntax bandwidth-based-sharing Undo bandwidth-based-sharing String, the end of a string Special characters for regular expressions 931 Syntax display ip routing-table acl acl-number verbose Display ip routing-table acl 933 IP Routing Table Commands 935 Display ip routing-table ip-address Display ip routing-table ip-address mask Display ip routing-table ip-addressDisplay ip routing-table ip-addresslonger-match Display ip routing-table ip-address mask longer-match 937 Display ip routing-table ip-prefix For detailed description of the above output, see Table Display ip routing-table protocol939 # Display summary information about static routes Display ip routing-table statisticsView Any view Display ip relay-tunnel Display ip relay-routeDisplay ip relay-route vpn-instance vpn-instance-name # Display recursive route information Display ipv6 routing-table Display load-sharing ip addressExamples # Display recursive tunnel information Syntax display ipv6 routing-table Syntax display ipv6 routing-table acl acl6-number verbose Display ipv6 routing-table acl943 Refer to for description about the above output Display ipv6 routing-table ipv6-addressDisplay ipv6 routing-table ipv6-addressprefix-length 945 Display ipv6 routing-table ipv6-address1 ipv6-address2 Display ipv6 routing-table protocol Display ipv6 routing-table ipv6-prefix Syntax display ipv6 routing-table statistics Display ipv6 routing-table statistics# Display routing statistics 947 Display ipv6 relay-route Display ipv6 routing-table verboseDisplay ipv6 routing-table verbose Entire routing table and information for each route Display ipv6 relay-tunnel Display ipv6 relay-tunnel# Display IPv6 recursive tunnel information 949 Load-bandwidth Reset load-sharingSyntax load-bandwidth bandwidth Undo load-bandwidth Reset ipv6 routing-table statistics Reset ip routing-table statistics protocolReset ipv6 routing-table statistics protocol all protocol Ripng , or static Sysname reset ipv6 routing-table statistics protocol all Configuration Commands on BGP Configuration CommandsAggregate Functions of the keywords Balance BGP/BGP-VPN instance view If-match clause of the route-policy commandSyntax balance number Undo balance Suppress-policy Bestroute as-path-neglect BGP/BGP-VPN instance view Related commands display bgp routing-tableView BGP view/BGP-VPN instance view 955 Bestroute compare-med BGP/BGP-VPN instance view Comparison is not enabled by defaultBestroute med-confederation BGP/BGP-VPN instance view Syntax bestroute compare-med Undo bestroute compare-med Compare-different-as-med BGP/BGP-VPN instance view Bgp957 Syntax confederation id as-number Undo confederation id Confederation id Confederation nonstandard Related commands confederation id and confederation peer-asConfederation peer-as View BGP view Undo confederation peer-as as-number-list Dampening BGP/BGP-VPN instance viewExamples # Specify confederation peer sub ASs 2000 Undo dampening Examples # In BGP view, configure BGP route dampening Default ipv4-unicastSyntax default ipv4-unicast Undo default ipv4-unicast 961 Default med BGP/BGP-VPN instance view Default local-preference BGP/BGP-VPN instance viewSyntax default med med-value Undo default med Syntax default-route imported Undo default-route imported Default-route imported BGP/BGP-VPN instance view963 Description on the fields of the display bgp group command Related commands import-routeBGP/BGP-VPN instance viewDisplay bgp group Syntax display bgp group group-name Display bgp network Advertised with the network commandDisplay bgp network # Display routing information that has been advertised Display bgp paths Description on the fields of the display bgp paths commandDisplay bgp peer MED 967 Description on the fields of the display bgp peer command Display bgp routing-table Description on the fields of the display bgp routing command 969 Display bgp routing-table as-path-acl Display bgp routing-table cidr Display bgp routing-table cidr Display bgp routing-table community-list Display bgp routing-table community971 Display bgp routing-table dampened Display bgp routing-table dampenedDampened BGP routes # Display dampened BGP routes Display bgp routing-table dampening parameter Related commands dampening BGP/BGP-VPN instance viewDisplay bgp routing-table different-origin-as Display bgp routing-table dampening parameter Longer-match Display bgp routing-table flap-info Display bgp routing-table peer Related commands display bgp peer975 Display bgp routing-table statistic Display bgp routing-table regular-expressionEbgp-interface-sensitive Display bgp routing-table statistic Undo ebgp-interface-sensitive Filter-policy export BGP/BGP-VPN instance view977 Filter-policy import BGP/BGP-VPN instance view Graceful-restart BGP view Graceful-restart timer restartSyntax graceful-restart Undo graceful-restart 979 Graceful-restart timer wait-for-rib timer Graceful-restart timer wait-for-ribUndo graceful-restart timer wait-for-rib Using this command can speed up route convergence 981 Import-route BGP/BGP-VPN instance view Syntax log-peer-change Undo log-peer-change Log-peer-change 983 Network BGP/BGP-VPN instance view Peer advertise-ext-community BGP/BGP-VPN instance view Peer advertise-community BGP/BGP-VPN instance view Peer allow-as-loop BGP/BGP-VPN instance view Related commands display bgp routing-table peer985 Peer as-path-acl BGP/BGP-VPN instance view Peer as-number BGP/BGP-VPN instance viewUndo peer ip-address 987 Peer capability-advertise conventional Peer capability-advertise route-refresh Undo peer group-nameip-address default-route-advertise Peer default-route-advertise BGP/BGP-VPN instance viewPeer connect-interface BGP/BGP-VPN instance view Undo peer group-name ip-address connect-interface Peer description BGP/BGP-VPN instance view 991 Peer ebgp-max-hop BGP/BGP-VPN instance view Syntax peer ip-addressenable Undo peer ip-addressenable Peer enable BGP viewPeer fake-as BGP/BGP-VPN instance view Peer filter-policy BGP/BGP-VPN instance view Related commands peer as-path-aclBGP/BGP-VPN instance view993 Peer group BGP/BGP-VPN instance view Peer ip-prefix Peer ignore BGP/BGP-VPN instance view995 Peer keep-all-routes BGP/BGP-VPN instance view Peer next-hop-local BGP/BGP-VPN instance view Peer log-change BGP/BGP-VPN instance viewUndo peer group-name ip-address next-hop-local View BGP view /BGP-VPN instance view Peer password Peer preferred-value BGP/BGP-VPN instance view # Perform the similar configuration on the peerUndo peer group-name ip-address preferred-value 999 Undo peer group-name ip-address public-as-only Peer public-as-only BGP/BGP-VPN instance view 1001 Peer reflect-client BGP/BGP-VPN instance view Peer route-policy BGP/BGP-VPN instance view Peer route-limit BGP/BGP-VPN instance view 1003 Peer route-update-interval BGP/BGP-VPN instance view Undo peer group-nameip-address substitute-as Peer substitute-as BGP/BGP-VPN instance view Related commands timer BGP/BGP-VPN instance view Peer timer BGP/BGP-VPN instance view1005 Reflect between-clients BGP view Preference BGP/BGP-VPN instance viewUndo preference Syntax reflect between-clients Undo reflect between-clients Reflector cluster-id BGP view Examples # Disable route reflection between clientsExamples # Set the cluster ID to 1007 All Resets all BGP connections Reset bgpAs-number Resets BGP connections to peers in the AS Refresh bgp Reset bgp flap-info Reset bgp dampening1009 Syntax reset bgp ipv4 all Reset bgp ipv4 allRouter-id Syntax router-id router-id Undo router-id Syntax summary automatic Undo summary automatic Summary automatic1011 Syntax timer keepalive keepalive hold holdtime Undo timer Timer BGP/BGP-VPN instance viewSynchronization BGP view Syntax synchronization Undo synchronization 1013 Related commands peer timer BGP/BGP-VPN instance view BGP Configuration Commands Debugging bgp all BGP Debugging Commands BGP received an Open message from the peer BGP configuration information Syntax debugging bgp detail Undo debugging bgp detail Debugging bgp detail1017 Route was deleted from the instance Debugging bgp event Debugging bgp graceful-restart BGP has received an Update messageState has changed from Opensent to Openconfirm 1019 BGP peer relationship has been successfully established BGP neighbor 10.1.1.1 is performing GRBGP GR Helper received an EOR message from peer Debugging bgp Description on the fields of the debugging bgp command1021 Information about the sent BGP Open message Description on the fields of the debugging bgp open commandAFI/ Safi WTR Information about the sent BGP Keepalive message Information about the received BGP Open messageInformation about the received BGP Keepalive message 1023 ConnectRetry timer for BGP peer 2.2.2.2 expired Debugging bgp timer Receive Enables the debugging for received BGP packets Hold timer expired on BGP peerSend Enables the debugging for sent BGP packets Update messages Ip-prefix-name receive send verbose Debugging bgp update ipv4Ip-prefix ip-prefix-name receive send verbose Update messages of IPv4 address family Debugging bgp update ipv61027 Send Enables/disables debugging for sent BGP packets Receive Enables/disables debugging for received BGP packetsFor IPv6 BGP update messages Complete By default, this debugging is disabled Update messages of IPv6 address family Debugging bgp update l2vpnVerbose Send verbose Update messages in an L2VPN environment Debugging bgp update label-routeAcl-number ip-prefix ip-prefix-name receive send verbose Receive send verbose 1031 Update message information of L3VPN labeled routes Update message information of IPv6 labeled routes Debugging bgp update peer Vpls Update messages Debugging bgp update vplsFor BGP Vpls Update messages 1033 Information about the sent Vpls update message Debugging bgp update vpn-instanceInformation about the received Vpls update message BGP VPNv4 Update messages Debugging bgp update vpnv4For BGP VPNv4 Update messages Examples None Update message information of VPNv4 Area-authentication-mode IS-IS Configuration CommandsArea-authentication-mode simple md5 password ip osi Undo area-authentication-mode Syntax auto-cost enable Undo auto-cost enable Auto cost enableRelated commands bandwidth-referenceIS-IS view, cost-style Bandwidth-reference IS-IS view Circuit-cost Related commands auto cost enable1039 Cost-style Related commands isis cost, cost-styleRelax-spf-limit Undo cost-style Related commands isis cost Default-route-advertise IS-IS view1041 Display isis brief Description on the fields of the display isis brief command Display isis graceful-restart status Display isis debug-switches Traffic-eng Displays IS-IS traffic engineering information Display isis interfaceVerbose Displays IS-IS interface detail information Tunnel Displays IS-IS tunnel information # Display detailed IS-IS interface information Examples # Display IS-IS enabled interface information1045 DIS Syntax display isis license Display isis licenseBFD License information varies with device models Display isis lsdb Lspid Display isis mesh-groupATT/P/OL # Configure a static mapping for the remote IS-IS system # Display the configuration information of IS-IS mesh-groupDisplay isis name-table Display isis peer Up state and direct interface’s IP address Display isis route# Display detailed IS-IS neighbor information PRI # Display IS-IS IPv4 routing information Description on the fields of the display isis route command1051 Display isis spf-log Display isis statistics Simple Specifies to send the password in plain text Domain-authentication-modeMd5 Specifies to send the password encrypted with MD5 IS-IS view 1055 Filter-policy export IS-IS view Filter-policy import IS-IS view Related commands filter-policy import IS-IS view Flash-flood Related commands filter-policy export IS-IS viewLevel-1 level-2 Undo flash-flood level-1 level-2 Graceful-restart interval IS-IS view Graceful-restart IS-IS viewGraceful-restart Import-route IS-IS view Graceful-restart suppress-saGraceful-restart suppress-sa Undo graceful-restart suppress-sa Related commands import-route isis level-2 into level-1 Import-route isis level-2 into level-1 Related commands import-routeIS-IS viewExamples # Redistribute static routes and set the cost to Undo import-route isis level-2 into level-1 Isis Isis authentication-mode Isis circuit-level level-1 level-1-2 level-2 This command is not available in loopback interface viewUndo isis circuit-level 1063 Isis circuit-type Related commands is-levelSyntax isis circuit-type p2p Undo isis circuit-type Isis cost Syntax isis dis-name symbolic-name Undo isis dis-nameIsis dis-name 1065 Isis dis-priority Examples # Configure the name as Localarea for the local LAN Syntax isis enable process-id Undo isis enable Isis enableRelated commands isis, network-entity Isis mesh-group Syntax isis peer-ip-ignore Undo isis peer-ip-ignore Isis peer-ip-ignore Syntax isis silent Undo isis silent Isis small-helloSyntax isis small-hello Undo isis small-hello 1069 Isis timer hello Isis timer csnp Isis timer holding-multiplier value level-1 level-2 Isis timer holding-multiplierUndo isis timer holding-multiplier level-1 level-2 Related commands isis timer hello Isis timer lspSyntax isis timer lsp time count count Undo isis timer lsp Related commands isis timer retransmit Related commands Examples Isis timer lsp Isis timer retransmitIs-level Syntax is-level level-1 level-1-2 level-2 Undo is-level Examples # Configure the router to work in Level-1 Related commands isis circuit-levelIs-name Syntax is-name sys-name Undo is-name Syntax is-snmp-traps enable Undo is-snmp-traps Is-snmp-traps enableIs-name map Undo is-name map sys-id Lsp-fragments-extend Log-peer-change IS-IS view 1077 Lsp-length originate Lsp-length receive # Restore the defaultMaximum load-balancing IS-IS view Syntax lsp-length receive size Undo lsp-length receive Network-entity Related commands Isis, isis enable ExamplesPreference IS-IS view Network-entity net Examples # Clear all IS-IS data structure information Reset isis all Set-overload Reset isis peerAllow interlevel external Undo set-overload Syntax spf-slice-size duration-time Undo spf-slice-size Spf-slice-size 1083 Summary IS-IS view Undo timer lsp-generation level-1 level-2 Timer isp-generationGeneration interval Interval Timer lsp-refresh Timer lsp-max-ageSyntax timer lsp-max-age seconds Undo timer lsp-max-age Related commands timer lsp-refresh Related commands timer lsp-max-age Timer spfUndo timer spf Examples # Set the LSP refresh interval to 1500 seconds # Set the maximum SPF calculation interval to 15 seconds Virtual-systemUndo virtual-system virtual-system-id 1087 IS-IS Configuration Commands Event Enables IS-IS event debugging IS-IS Debugging CommandsDebugging isis Ha-events interface-information memory-allocating IS-IS Debugging Commands Snpa Snpa 1091 Field 1093 CircuitName not enabled SNP packet length mismatch Length length 1095 Updt Reset Required Sending pduLevel pduType on circuitName 1097 Sending pduLevel Csnp PDU fails 1099 Tent New Distance from RootNodeSourceId LSP 1101 LevelType LSP level, which can be L1 or L2 1103 Router B sent Csnp packets IP address took effect on the IS-IS interface 1105 IS-IS Debugging Commands Related commands Ospf Configuration CommandsL3VPN Configuration Commands on Abr-summary Ospf area view Asbr-summary Area Ospf viewSyntax area area-id Undo area area-id Simple Specifies the simple authentication mode Authentication-modeDisplay ospf asbr-summary View Ospf area view Related commands ospf authentication-mode DefaultSyntax default cost cost limit limit tag tag type type Bandwidth-reference Ospf view Undo default cost limit tag type Default-cost Ospf area viewRelated commands import-route Ospf view Syntax default-cost cost Undo default-cost Related commands stub Ospf area view, nssa Default-route-advertise Ospf viewDefault-route-advertise summary cost cost Undo default-route-advertise Display ospf abr-asbr Description OSPF/OSPF area viewSyntax description description Undo description # Describe the Ospf area0 as bone area Display ospf asbr-summary Display ospf brief Related commands asbr-summarySyntax display ospf process-id brief Examples # Display Ospf brief information Mpls TE Description on the fields of the display ospf brief command Syntax display ospf process-id cumulative Display ospf cumulative1117 Syntax display ospf process-id error Display ospf errorNssa ASE/NSSA 1119 Description on the fields of the display ospf error command Display ospf interface 1121 Display ospf lsdbBDR # Display Type2 LSA Network LSA information in the Lsdb Description on the fields of the display ospf lsdb command Syntax display ospf process-id nexthop Display ospf nexthop1123 LS ID Display ospf peer Display ospf peer statistics Description on the fields of the display ospf peer command# Display brief Ospf neighbor information Syntax display ospf process-id peer statistics Keep neighbor relationship Init Display ospf request-queue Examples # Display Ospf request list information Display ospf retrans-queue1127 Display ospf routing Display ospf vlink Description on the fields of the display ospf vlink commandSyntax display ospf process-id vlink 1129 Enable log Enable link-local-signalingError Enables error logging State Enables state logging Filter import/export Enable out-of-band-resynchronization1131 This command is only available on an ABR By default, Summary LSAs filtering is disabledFilter-policy export Ospf view Undo filter-policy export protocol process-id Filter-policy import Ospf view Examples # Filter redistributed routes using ACLGraceful-restart Ospf view 1133 # Enable non-IETF Graceful Restart for Ospf process Examples # Enable Ietf Graceful Restart for Ospf processGraceful-restart help Syntax graceful-restart help acl-numberprefix prefix-list Graceful-restart interval Ospf view Related commands ospf timer deadHost-advertise 1135 Import-route Ospf view Default-route-advertise Ospf view Related commands ExamplesImport-route command cannot redistribute default routes 1137 Lsa-arrival-interval Related commands lsa-generation-interval Lsa-generation-interval Related commands lsa-arrival-intervalLsdb-overflow-limit Undo lsa-generation-interval Maximum-routes Maximum load-balancing Ospf viewNumber Maximum route number in the range 1 to Network Ospf area view Related commands ospfNssa 1141 Related commands default-cost Ospf area view Opaque-capability enableExamples # Configure area1 as an Nssa area Syntax opaque-capability enable Undo opaque-capability Ospf Ospf authentication-modeUndo ospf process-id 1143 Related commands authentication-mode Syntax ospf cost value Undo ospf cost Ospf cost1145 Ospf mib-binding Ospf dr-prioritySyntax ospf dr-priority priority Undo ospf dr-priority Syntax ospf mib-binding process-id Undo ospf mib-binding Ospf network-type Ospf mtu-enable Related commands ospf dr-priority Ospf timer deadThis command is not supported on the Null interface Syntax ospf timer dead seconds Undo ospf timer dead Related commands ospf timer hello Ospf timer helloSyntax ospf timer hello seconds Undo ospf timer hello 1149 Ospf timer retransmit Ospf timer pollSyntax ospf timer poll seconds Undo ospf timer poll Syntax ospf trans-delay seconds Undo ospf trans-delay Ospf trans-delayPeer 1151 Preference Command sets priority for internal routesExamples # Specify the neighbor IP address Preference ase route-policy route-policy-name value Reset ospf process Reset ospf countersSyntax reset ospf process-id process 1153 Syntax reset ospf process-id redistribution Reset ospf redistributionRfc1583 compatible Syntax rfc1583 compatible Undo rfc1583 compatible Silent-interface Ospf view Snmp-agent trap enable ospf Ospf Configuration Commands Stub Ospf area view Spf-schedule-intervalUndo spf-schedule-interval Syntax stub no-summary Undo stub Stub-router Default-cost Ospf area viewStub-router Undo stub-router Vlink-peer Ospf area view Examples # Enable a stub-router1159 Related commands authentication-mode,display ospf peer Default cost RIP view RIP Configuration CommandsSyntax default cost value Undo default cost Checkzero Related commands import-route RIP view Default-route originate# Disable default route sending Display rip 1163 Description on the fields of the display rip command Display rip database Description on fields of the display rip database commandSyntax display rip process-iddatabase X.X/X Display rip route Display rip interface1165 RIP Configuration Commands Filter-policy export RIP view Description on the fields of the display rip route command# Display the routing statistics of RIP process 1167 Interface-type interface-number Specifies an interface Filter-policy import RIP viewExamples # Reference ACL 2000 to filter outbound routes Syntax host-route Undo host-route Host-route1169 Import-route RIP view Default cost RIP viewIncluding bgp , direct , isis , ospf , rip , rip and static Maximum load-balancing RIP view # Set the default cost for redistributed routes to1171 Syntax peer ip-address Syntax reset rip process-idstatistics Reset rip statisticsRip 1173 Undo rip authentication-mode Rip authentication-mode By default, an interface is enabled to receive RIP messages Mode and parameters# Enable Ethernet1/0 to receive RIP messages Format defined in RFC Related commands rip metricin Related commands rip metricoutRip metricin Rip metricout Rip output Rip mib-bindingSyntax rip mib-binding process-id Undo rip mib-binding Syntax rip output Undo rip output Rip poison-reverse Related commands rip inputRip split-horizon Related commands summary Examples # Enable the split horizon function on Ethernet1/0Rip summary-address Rip triggered Undo rip triggered Rip versionRip version 1 2 broadcast multicast Undo rip version All Silents all interfaces Silent-interface RIP viewMessages 1181 Related commands rip version TimersSummary Syntax summary 1183 Trip retransmit count Trip retransmit timer retransmit-time-value Trip retransmit timerUndo trip retransmit timer Version Validate-source-addressSyntax validate-source-address Undo validate-source-address Version 1 Sysname system-view Sysname rip Sysname-rip-100 version Apply as-path Routing Policy Common Configuration CommandsApply comm-list delete Syntax apply comm-list comm-list-numberdelete Undo apply comm-list Apply community Syntax apply cost + value Undo apply cost Apply costView Routing policy view Parameters + Increases cost value. + Decreases cost value Apply extcommunity Apply cost-type Apply isis No level is set by defaultApply isis level-1 level-1-2 level-2 Undo apply isis 1191 Apply local-preference Related commands route-policyApply mpls-label Syntax apply mpls-label Undo apply mpls-label Apply preference Apply originSyntax apply preference preference Undo apply preference 1193 Apply tag Apply preferred-valueSyntax apply tag value Undo apply tag Syntax display ip as-path as-path-acl number Display ip as-pathExamples # Display the information of BGP AS path ACL 1195 Display ip extcommunity-list Display ip community-listSyntax display ip extcommunity-list ext-comm-list-number If-match as-path Display route-policySyntax display route-policy route-policy-name Examples # Display the information of routing policy Related commands route-policyand ip community-list Related commands route-policy,ip as-pathaclIf-match community If-match extcommunity If-match costSyntax if-match cost value Undo if-match cost 1199 If-match interface If-match route-type If-match mpls-label Ip as-path If-match tagSyntax if-match tag value Undo if-match tag Undo ip as-path as-path-number 1203 Ip community-list Sysname system-view Sysname ip community-list 100 permit Route-policy Ip extcommunity-listUndo ip extcommunity-list ext-comm-list-number 1205 Routing Policy Common Configuration Commands Display ip ip-prefix IPV4 Routing Policy Configuration CommandsSyntax display ip ip-prefix ip-prefix-name Examples # Display the statistics of IPv4 prefix list abc Related commands ip ip-prefix If-match ip Related commands Route-policy ExamplesIf-match ip-prefix Ip ip-prefix Syntax reset ip ip-prefix ip-prefix-name Reset ip ip-prefix1211 IPV4 Routing Policy Configuration Commands Apply ipv6 next-hop IPV6 Routing Policy Configuration CommandsDisplay ip ipv6-prefix Syntax display ip ipv6-prefix ipv6-prefix-name Next-hop Matches the next hop of IPv6 routing information If-match ipv6String of 1 to 19 characters Address based match criterion for IPv6 routes 1215 Ip ipv6-prefix Syntax reset ip ipv6-prefix ipv6-prefix-name Reset ip ipv6-prefixExamples # Clear the statistics of IPv6 prefix list abc Delete static-routes all Static Routing Configuration CommandsIp route-static Examples # Delete all static routes on the router Configured gateway-address Ethernet interface and Vlan interface Must be identical to that configured in the NQA test groupAssociate it with a Track entry 1219 Examples # Set the default preference of static routes to Ip route-static default-preference Related commands display ipv6 routing-tableon IPV6 BGP Configuration CommandsBalance IPv6 address family view Bestroute as-path-neglect IPv6 address family view Bestroute med-confederation IPv6 address family view Bestroute compare-med IPv6 address family view 1223 Compare-different-as-med IPv6 address family view Dampening IPv6 address family view Default med IPv6 address family view Default local-preferenceIPv6 address family view1225 Display bgp ipv6 group Default-route imported IPv6 address family viewSyntax display bgp ipv6 group ipv6-group-name Syntax display bgp ipv6 network Display bgp ipv6 network1227 Syntax display bgp ipv6 paths as-regular-expression Display bgp ipv6 paths 1229 Display bgp ipv6 peerIncomplete Field Description Local router ID Display bgp ipv6 routing-table 1231 Display bgp ipv6 routing-table as-path-acl Examples # Display routes filtered through the AS path ACL Display bgp ipv6 routing-table community Display bgp ipv6 routing-table dampened Display bgp ipv6 routing-table community-listSyntax display bgp ipv6 routing-table dampened Examples # Display IPv6 BGP dampened routes Display bgp ipv6 routing-table different-origin-as Display bgp ipv6 routing-table dampening parameterSyntax display bgp ipv6 routing-table dampening parameter Syntax display bgp ipv6 routing-table different-origin-as Examples # Display IPv6 BGP routes from different ASs Display bgp ipv6 routing-table flap-infoExamples # Display IPv6 BGP route flap statistics 1235 Display bgp ipv6 routing-table label CommandSyntax display bgp ipv6 routing-table label Examples # Display IPv6 BGP label routing information Display bgp ipv6 routing-table regular-expression Display bgp ipv6 routing-table peer1237 Filter-policy exportIPv6 address family view Display bgp ipv6 routing-table statisticParameters as-regular-expression AS regular expression Syntax display bgp ipv6 routing-table statistic 1239 Filter-policy import IPv6 address family view Import-route IPv6 address family view Group IPv6 address family viewExamples # Reference ACL6 2001 to filter all inbound routes Syntax group ipv6-group-name internal external Network IPv6 address family view Ipv6-familySyntax ipv6-family Undo ipv6-family 1241 Peer advertise-community IPv6 address family view Peer allow-as-loop IPv6 address family view Peer advertise-ext-community IPv6 address family view1243 Peer as-number IPv6 address family view Import export Peer as-path-acl IPv6 address family view1245 Peer connect-interface IPv6 address family view Peer description IPv6 address family view Peer default-route-advertise1247 Peer ebgp-max-hop IPv6 address family view Peer fake-as IPv6 address family view Peer enable IPv6 address family view1249 Peer filter-policy IPv6 address family view Peer ignore IPv6 address family view Peer group IPv6 address family view1251 Peer ipv6-prefix Peer label-route-capability IPv6 address family view Peer keep-all-routes IPv6 address family view1253 Peer next-hop-local IPv6 address family view Peer log-change IPv6 address family view 1255 Peer preferred-value IPv6 address family view Peer reflect-client IPv6 address family view Peer public-as-only IPv6 address family view 1257 Peer route-limit IPv6 address family view Peer route-policy IPv6 address family view Peer route-update-interval IPv6 address family view Peer substitute-as IPv6 address family view Undo peer ipv6-group-nameipv6-address route-update-interval1259 Related commands timer IPv6 address family view Peer timer IPv6 address family viewPreference IPv6 address family view 1261 Reflect between-clients IPv6 address family view Reflector cluster-id IPv6 address family view Examples # Enable route reflection between clientsRefresh bgp ipv6 1263 Reset bgp ipv6 Reset bgp ipv6 flap-info Reset bgp ipv6 dampening 1265 Synchronization IPv6 address family view Timer IPv6 address family view 1267 Related commands peer timer IPv6 address family view IPV6 BGP Configuration Commands IPV6 IS-IS Configuration Commands # Display detailed IPv6 IS-IS routing information 1271 Ipv6 default-route-advertise Syntax ipv6 enable Undo ipv6 enable Ipv6 enableIpv6 filter-policy export Undo ipv6 filter-policy export protocol process-id Ipv6 filter-policy import Related commands ipv6 filter-policy importUndo ipv6 filter-policy import 1273 Ipv6 import-route Related commands ipv6 filter-policy export Undo ipv6 import-route isisv6 level-2 into level-1 Ipv6 import-route isisv6 level-2 into level-11275 Ipv6 preference Ipv6 maximum load-balancing 1277 Ipv6 summary Examples # Configure a summary route of 2002/32 Isis ipv6 enableSyntax isis ipv6 enable process-id Undo isis ipv6 enable Abr-summary OSPFv3 area view IPV6 OSPFV3 Configuration CommandsArea OSPFv3 view Default-cost OSPFv3 area view Default costSyntax default-cost value Examples # Enter OSPFv3 Area 0 view Display debugging ospfv3 Related commands stubOSPFv3 area viewDisplay debugging ospfv3 Debugging state information Display ospfv3 Description on the fields of the display isofv3 commandSyntax display ospfv3 process-id 1283 Display ospfv3 interface Display ospfv3 lsdb 1285 # Display Link-local LSA information in the Lsdb Syntax display ospfv3 lsdb statistic Display ospfv3 lsdb statistic Display ospfv3 peer Display ospfv3 next-hopSyntax display ospfv3 process-id next-hop Interface-type interface-number interface type and number Description on the fields of the display isofv3 peer command Display ospfv3 request-list Display ospfv3 peer statisticSyntax display ospfv3 peer statistic Syntax display ospfv3 process-id request-list statistics # Display the statistics of OSPFv3 link state request list Display ospfv3 retrans-listSyntax display ospfv3 process-id retrans-list statistics LS-ID 1291 Display ospfv3 routing # Display the statistics of OSPFv3 routing table Display ospfv3 topology Display ospfv3 statisticSyntax display ospfv3 statistic Syntax display ospfv3 process-id topology area area-id Syntax display ospfv3 process-id vlink Display ospfv3 vlink 1295 Filter-policy exportOSPFv3 view Routes that fail to pass are not added to the routing table Filter-policy importOSPFv3 view Allow-ibgp direct static cost value type type route-policy Import-routeOSPFv3 viewDirect static Both Ebgp and Ibgp routes Process Maximum load-balancingOSPFv3 view Ospfv3 Related commands router-idOspfv3 area Undo ospfv3 process-id Ospfv3 dr-priority Ospfv3 cost Ospfv3 mtu-ignore Ospfv3 timer dead1301 Related commands ospfv3 timer hello Ospfv3 timer hello Ospfv3 trans-delay Ospfv3 timer retransmitRelated commands ospfv3 timer dead 1303 Preference ase route-policy route-policy-name preference Silent-interfaceOSPFv3 view Related commands Ospfv3Router-id router-id OSPFv3 processes on a router Undo spf timers Spf timers Examples # Configure OSPFv3 area 1 as a stub area Related commands default costUndo vlink-peer router-id hello retransmit trans-delay dead StubOSPFv3 area view IPV6 OSPFV3 Configuration Commands Default cost RIPng view IPV6 Ripng Configuration CommandsSyntax default cost cost Undo default cost View RIPng view Display ripng Related commands import-routeSyntax display ripng process-id Description on fields of the display ripng database command Description on the fields of the display ripng commandDisplay ripng database Syntax display ripng process-iddatabase Display ripng interface Syntax display ripng process-idroute Display ripng route1313 Filter-policy import RIPng view Filter-policy export 1315 Import-route Maximum load-balancing RIPng view Related commands default cost on # Disable RIPng process # Restore the default RIPng route priorityRipng Undo ripng process-id Ripng enable Ripng default-routeSyntax ripng process-idenable Undo ripng enable Ripng metricin Related commands ripng metricoutRipng metricout Syntax ripng metricin value Undo ripng metricin Ripng poison-reverse Related commands ripng metricinRipng split-horizon Syntax ripng poison-reverse Undo ripng poison-reverse Lapb and X.25 Configuration Commands on Information, refer to Frame Relay Configuration Commands onRipng summary-address Poison reverse function takes effect Timers 1323 IPV6 Ripng Configuration Commands Delete ipv6 static-routes all IPV6 Static Routing Configuration CommandsIpv6 route-static Delete ipv6 static-routes all Sysname system-view Sysname ipv6 route-static 112 24 Related command multicast boundary Multicast Routing Forwarding Configuration CommandsDisplay multicast boundary Display multicast forwarding-table 1329 Major values of the flags fieldMID Value Meaning Display multicast minimum-ttl Related command multicast minimum-ttl Display multicast routing-table Related command display multicast forwarding-table1331 Description on the fields of display multicast routing-table Display multicast routing-table static 1333 Display multicast rpf-info Ip rpf-route-static 1335 Mtracert Related command display multicast routing-table static Multicast boundary Description on the fields of the mtracert command1337 Multicast forwarding-table downstream-limit Related command display multicast boundary 1339 Multicast forwarding-table route-limit Multicast longest-match Multicast load-splittingSyntax multicast longest-match Undo multicast longest-match View System view, VPN instance view Related command display multicast minimum-ttl Multicast routing-enableMulticast minimum-ttl 1341 # Enable IP multicast routing in VPN instance mvpn Reset multicast forwarding-table 1343 Reset multicast routing-table Sysname reset multicast routing-table Display igmp group Igmp Configuration Commands Display igmp interface Description on the fields of the display igmp group command 1347 Display igmp routing-table Fast-leave Igmp view Related command igmp fast-leave,last-member-query-intervalIgmp Syntax fast-leave group-policy acl-number Undo fast-leave Related command igmp enable, and multicast routing-enableon Igmp enableSyntax igmp enable Undo igmp enable Related command igmp Igmp group-policy Igmp fast-leaveUndo igmp group-policy 1351 Igmp last-member-query-interval By default, the last-member query interval is 1 secondIgmp max-response-time 1353 Igmp require-router-alert Igmp robust-count Robust-count Igmp view , igmp timer query , igmpIgmp send-router-alert Igmp interface Igmp static-group Igmp timer query Igmp timer other-querier-present Igmp version Related command version Igmp viewLast-member-query-interval Undo igmp version Require-router-alert Igmp view Max-response-time Igmp viewSyntax require-router-alert Undo require-router-alert Reset igmp groupView Public instance Igmp view, VPN instance Igmp view 1359 Robust-count Igmp view Related command display igmp groupSyntax robust-count robust-value Undo robust-count Send-router-alert Igmp view Timer other-querier-present Igmp viewSyntax send-router-alert Undo send-router-alert 1361 Syntax timer query interval Undo timer query Timer query Igmp viewPublic instance Version Igmp view Related command igmp version1363 Igmp Configuration Commands Cache-sa-enable Msdp Configuration CommandsDisplay msdp brief Characters Display msdp peer-status 1367 Display msdp sa-cache 1369 Related command cache-sa-enable Display msdp sa-count Syntax encap-data-enable Undo encap-data-enable Encap-data-enableImport-source View Public instance Msdp view, VPN instance Msdp view Related command display multicast routing-tableon Related command peer sa-policyMsdp Peer connect-interface Originating-rpUndo originating-rp 1373 Related command display msdp peer-status Related command static-rpf-peerPeer description Peer mesh-group Undo peer peer-addressmesh-group Peer minimum-ttlUndo peer peer-addressminimum-ttl 1375 Peer sa-cache-maximum Peer request-sa-enable Peer sa-policy Import-source commandFrom the Msdp peer Display msdp peer-status and import-source Peer sa-request-policy Reset msdp peer Related command cache-sa-enableand display msdp sa-cache Reset msdp sa-cache1379 Shutdown Msdp View Reset msdp statisticsUndo shutdown peer-address Example # Configure static RPF peers in the public instance Related command display msdp peer-statusand ip prefix-listStatic-rpf-peer Undo static-rpf-peer peer-address Syntax timer retry interval Undo timer retry Timer retry Auto-rp enable PIM Configuration CommandsRelated command static-rp PIM view Bsr-policy PIM view Undo c-bsr Bsr PIM view Syntax c-bsr admin-scope Undo c-bsr admin-scope Bsr admin-scopeBsr global 1385 Undo c-bsr group group-address Bsr group Bsr holdtime PIM view Bsr hash-length PIM viewSyntax c-bsr hash-length hash-length Undo c-bsr hash-length Syntax c-bsr holdtime interval Undo c-bsr holdtime Bsr interval PIM view Related command c-bsr PIM view and c-bsr interval PIM viewBsr priority PIM view Bsr PIM view and c-bsr holdtime PIM view 1389 Rp PIM view Rp advertisement-interval PIM view Related command c-bsr PIM viewRp advertisement-interval interval Undo c-rp advertisement-interval Rp holdtime PIM view Related command c-rp PIM view and c-bsr interval PIM viewCrp-policy PIM view Syntax c-rp holdtime interval Undo c-rp holdtime Display pim bsr-info Related command c-bsr PIM view and c-rp PIM view 1393 Display pim claimed-route Display pim control-message counters BSR 1395 Display pim grafts Description on the fields of the display pim grafts commandDisplay pim interface 1397 PIM DR Display pim join-prune 1399 Display pim neighbor Interface connecting the PIM neighbor 1401 Display pim routing-table Sysname display pim routing-table Vpn-instance public net 1403 Display pim rp-info Description on the fields of the display pim rp-info command Hello-option dr-priority PIM view Related command pim hello-optiondr-priorityHello-option holdtime PIM view 1405 This command is effective for both PIM-DM and PIM-SM Hello-option lan-delay PIM viewRelated command pim hello-option holdtime Hello-option neighbor-tracking PIM view Hello-option override-interval PIM view Related command pim hello-optionneighbor-tracking1407 Holdtime join-prune PIM view Holdtime assert PIM viewSyntax holdtime assert interval Undo holdtime assert Jp-pkt-size PIM view Related command jp-queue-size PIM viewJp-queue-size PIM view Syntax jp-pkt-size packet-size Undo jp-pkt-size Pim Related command multicast routing-enableonUndo pim vpn-instance vpn-instance-name Pim dm Pim bsr-boundaryBsr PIM view , and multicast boundary on Example # Enable PIM-DM on Ethernet 1/0 Related command pim sm, ssm-policy PIM viewRelated command hello-optiondr-priority PIM view Pim hello-option dr-priority Related command hello-option holdtime PIM view Pim hello-option lan-delayPim hello-option holdtime 1413 Pim hello-option override-interval Pim hello-option neighbor-tracking Pim holdtime join-prune Pim holdtime assert1415 Pim sm Pim require-genidView Interface view Parameter None Related command pim dm Pim timer graft-retryExample # Enable PIM-SM on Ethernet 1/0 Example # Disable state refresh on Ethernet 1/0 Pim timer join-prune Pim timer helloSyntax pim timer hello interval Undo pim timer hello Related command timer hello PIM view Related command timer join-prune PIM view Pim triggered-hello-delayProbe-interval PIM view Syntax probe-interval interval Undo probe-interval Related command register-suppression-timeout PIM view Register-suppression-timeout PIM viewSyntax register-suppression-timeout interval Register-policy PIM view Register-whole-checksum PIM view Undo register-suppression-timeoutSyntax register-whole-checksum Undo register-whole-checksum 1421 Related command state-refresh-interval PIM view Reset pim control-message countersSource-lifetime PIM view Syntax source-lifetime interval Undo source-lifetime Undo spt-switch-threshold group-policy acl-number Spt-switch-threshold PIM viewSource-policy PIM view Syntax source-policy acl-number Undo source-policy PIM Configuration Commands State-refresh-interval PIM view Ssm-policy PIM viewSyntax ssm-policy acl-number Undo ssm-policy 1425 State-refresh-ttl PIM view State-refresh-rate-limit PIM viewSyntax state-refresh-ttl ttl-value Undo state-refresh-ttl Static-rp PIM view By default, the TTL value of state refresh messages isUndo static-rp rp-address 1427 Timer join-prune PIM view Timer hello PIM viewRelated command display pim rp-infoand auto-rp enable Related command pim timer hello Related command pim timer join-prune Timer spt-switch PIM viewSyntax timer spt-switch interval Undo timer spt-switch Related command spt-switch-threshold PIM view PIM Configuration Commands Related command multicast ipv6 boundary IPV6 Multicast Routing Forwarding Configuration CommandsDisplay multicast ipv6 boundary Display multicast ipv6 forwarding-table IPV6 Multicast Routing and Forwarding Configuration Commands Values and meanings of the Flags field Display multicast ipv6 minimum-hoplimit1433 Display multicast ipv6 routing-table Related command multicast ipv6 minimum-hoplimit Display multicast ipv6 rpf-info Related command display multicast ipv6 forwarding-table1435 Multicast ipv6 boundary Multicast ipv6 forwarding-table downstream-limit Related command display multicast ipv6 boundary1437 Multicast ipv6 load-splitting Multicast ipv6 forwarding-table route-limit Multicast ipv6 minimum-hoplimit Multicast ipv6 longest-match1439 Related command display multicast ipv6 minimum-hoplimit Multicast ipv6 routing-enable Reset multicast IPv6 routing-table Reset multicast ipv6 forwarding-table1441 Sysname reset multicast ipv6 routing-table ff03101 Display mld group MLD Configuration Commands Display mld interface Description on the fields of the display mld group commandInformation of all interfaces running MLD 1445 Display mld routing-table Syntax fast-leave group-policy acl6-number Undo fast-leave Fast-leave MLD view Max-response-time MLD view Last-listener-query-intervalSyntax max-response-time interval Undo max-response-time 1447 Syntax mld enable Undo mld enable Mld enableMld Syntax mld Example # Enable MLD on Ethernet 1/0 Related command mldMld fast-leave Mld group-policy Mld last-listener-query-interval Mld require-router-alert Mld max-response-time1451 Syntax mld robust-count robust-value Undo mld robust-count Mld robust-count Mld static-group Mld send-router-alertMld send-router-alert Undo mld send-router-alert Mld timer other-querier-present interval Mld timer other-querier-presentUndo mld timer other-querier-present 125 x 2 + 10 / 2 = 255 seconds Syntax mld timer query interval Undo mld timer query Mld timer queryRelated command mld version Mld version Require-router-alert MLD view Reset mld groupRequire-router-alert Mld require-router-alert and send-router-alert MLD view Robust-count MLD view Related command display mld group# Clear all MLD forwarding entries on Ethernet 1/0 1457 By default, the MLD querier robustness variable is Timer other-querier-present MLD viewSend-router-alert MLD view View MLD view Related command Timer query MLD viewTimer query interval Example # Globally set the MLD version to MLDv2 Version MLD view Bsr-policy IPv6 PIM view IPV6 PIM Configuration CommandsBsr IPv6 PIM view Syntax bsr-policy acl6-number Undo bsr-policy Bsr hash-length IPv6 PIM view Related command c-bsr IPv6 PIM view on Bsr holdtime IPv6 PIM view Example # Set the bootstrap timeout time to 150 secondsBsr interval IPv6 PIM view Syntax c-bsr interval interval Undo c-bsr interval Bsr priority IPv6 PIM view Related command c-bsr IPv6 PIM viewRp IPv6 PIM view Bsr IPv6 PIM view and c-bsr holdtime IPv6 PIM view View IPv6 PIM view Rp advertisement-interval IPv6 PIM view1465 Example # Set the global C-RP timeout time to 200 seconds Related command c-rp IPv6 PIM viewRp holdtime IPv6 PIM view Example # Set the global C-RP-Adv interval to 30 seconds Crp-policy IPv6 PIM view Related command c-bsr IPv6 PIM view and c-rp IPv6 PIM viewDisplay pim ipv6 bsr-info Syntax crp-policy acl6-number Undo crp-policy Syntax display pim ipv6 claimed-route ipv6-source-address Display pim ipv6 claimed-route Display pim ipv6 control-message counters BSR Display pim ipv6 interface Display pim ipv6 graftsDisplay pim ipv6 grafts Unacknowledged graft messages Interface PIM version PIM mode PIM-SM and IPv6 PIM-SSM respectively Display pim ipv6 join-pruneTo send on the specified interface Specified IPv6 PIM neighbor Display pim ipv6 neighbor 1475 Display pim ipv6 routing-table Example # View the content of the IPv6 PIM routing table Related command display multicast ipv6 routing-tableon Syntax display pim ipv6 rp-info ipv6-group-address Display pim ipv6 rp-info1477 Syntax embedded-rp acl6-number Undo embedded-rp acl6-number Embedded-rp Hello-option dr-priority IPv6 PIM view Related command pim ipv6 hello-optiondr-priorityHello-option holdtime IPv6 PIM view Example # Set the router priority for DR election to Related command pim ipv6 hello-option holdtime Hello-option lan-delay IPv6 PIM viewExample # Set the prune delay to 200 milliseconds globally Hello-option neighbor-tracking IPv6 PIM view Example # Disable join suppression globally Related command pim ipv6 hello-optionneighbor-trackingHello-option override-interval IPv6 PIM view Holdtime assert IPv6 PIM view Holdtime join-prune IPv6 PIM view Jp-pkt-size IPv6 PIM view Related command jp-queue-size IPv6 PIM viewJp-queue-size IPv6 PIM view 1483 Pim ipv6 Related command multicast ipv6 routing-enableonPim ipv6 bsr-boundary Syntax pim ipv6 Undo pim ipv6 Example # Enable IPv6 PIM-DM on Ethernet 1/0 Related commands pim ipv6 sm, ssm-policy IPv6 PIM viewPim ipv6 dm Syntax pim ipv6 dm Undo pim ipv6 dm Related command hello-option holdtime IPv6 PIM view Related command hello-optiondr-priority IPv6 PIM viewPim ipv6 hello-option dr-priority Pim ipv6 hello-option holdtime Pim ipv6 hello-option neighbor-tracking Pim ipv6 hello-option lan-delay1487 Example # Disable join suppression on Ethernet 1/0 Related command hello-optionneighbor-tracking IPv6 PIM viewPim ipv6 hello-option override-interval Pim ipv6 holdtime assert Pim ipv6 require-genid Pim ipv6 holdtime join-pruneSyntax pim ipv6 require-genid Undo pim ipv6 require-genid 1489 Pim ipv6 state-refresh-capable Pim ipv6 smPim ipv6 sm Undo pim ipv6 sm Pim ipv6 timer hello Pim ipv6 timer graft-retry1491 Pim ipv6 triggered-hello-delay Pim ipv6 timer join-pruneRelated command timer hello IPv6 PIM view Related command timer join-prune IPv6 PIM view Probe-interval IPv6 PIM view Related command register-suppression-timeout IPv6 PIM viewRegister-policy IPv6 PIM view Example # Set the probe time to 6 seconds Register-suppression-timeout IPv6 PIM view Register-whole-checksum IPv6 PIM view Reset pim ipv6 control-message counters1495 Source-lifetime IPv6 PIM view Related command state-refresh-interval IPv6 PIM viewSource-policy IPv6 PIM view Syntax source-policy acl6-number Undo source-policy Undo spt-switch-threshold group-policy acl6-number Spt-switch-threshold IPv6 PIM view1497 Syntax ssm-policy acl6-number Undo ssm-policy Ssm-policy IPv6 PIM view State-refresh-interval IPv6 PIM view State-refresh-hoplimit1499 Static-rp IPv6 PIM view State-refresh-rate-limit IPv6 PIM viewExample # Set the state refresh interval to 70 seconds Related command display pim ipv6 rp-info Timer hello IPv6 PIM viewUndo static-rp ipv6-rp-address 1501 Timer spt-switch IPv6 PIM view Timer join-prune IPv6 PIM viewRelated command pim ipv6 timer hello Related command pim ipv6 timer join-prune 1503 Related command spt-switch-threshold IPv6 PIM view IPV6 PIM Configuration Commands Display multicast-domain vpn-instance switch-group receive Multicast VPN Configuration CommandsDisplay multicast-domain vpn-instance share-group Count 1507 Display multicast-domain vpn-instance switch-group send Multicast-domain holddown-time Multicast-domain share-group Multicast-domain log switch-group-reuseView VPN instance view 1509 Multicast-domain switch-delay Undo multicast-domain switch-group-pool Multicast-domain switch-group-pool1511 Sysname system-view Sysname ip vpn-instance mvpn Display mpls fast-forwarding cache Mpls Basics Configuration CommandsDisplay mpls fast-forwarding cache verbose Syntax display mpls ilm label include text Display mpls ilm# Display all ILM entries Display mpls interface Related command display mpls statistics interface1515 Display mpls label label-value1 to label-value2 all Display mpls label Display mpls ldp all verbose begin exclude include Display mpls ldpMpls ldp system view , mpls ldp interface view Display mpls ldp cr-lsp Description on the fields of the display mpls ldp commandLSR ID Display mpls ldp interface Related command display mpls lspAll Displays all information 1519 # Display detailed information about all interfaces Example # Display information about all LDP interfaces All Displays information about all LSPs established by LDP Display mpls ldp IspDest-addr Destination address of the LSP Established by LDP Display mpls ldp peer Related command display mpls ldp # Display detailed information about all peers Example # Display information about all peers1523 Example # Display information about remote peer BJI Display mpls ldp remote-peer 1525 Display mpls ldp session # Display detailed information about all sessions Example # Display information about sessionsLAM MD5 1527 Display mpls ldp vpn-instance Example # Display information about VPN instance vpn1 Display mpls lspIncoming-interface Incoming interface of the LSPs Outgoing-interface Outgoing interface of the LSPs Include Includes the specified FEC Exclude Excludes the specified FECDest-addr Destination address Asbr Displays information about Asbr established LSPs Example # Display information about all LSPs Description on the fields of the display mpls lsp command# Display detailed information about all LSPs FEC Display mpls nhlfe Display mpls lsp statisticsSyntax display mpls lsp statistics Syntax display mpls nhlfe token include text # Display all Nhlfe entries Display mpls route-state 1533 Display mpls static-lsp Example # Display brief information about static LSPs Display mpls statistics interface# Display detailed information about static LSPs Example # Display Mpls statistics for all interfaces Related command statistics interval1535 Syntax display mpls statistics lsp index all name lsp-name Display mpls statistics lsp 1537 Example # Display Mpls statistics for all LSPs Syntax du-readvertise timer value Undo du-readvertise timer Du-readvertise timerDu-readvertise Are both Graceful-restart mpls ldp Graceful-restart Mpls LDP viewView Mpls LDP view Syntax graceful-restart mpls ldp Graceful-restart timer reconnect Graceful-restart timer neighbor-livenessRelated commands graceful-restart Mpls LDP view Syntax graceful-restart timer reconnect timer Undo graceful-restart timer reconnect Graceful-restart timer recovery1541 Hops-count Related command loop-detect,path-vectorsLabel advertise Syntax hops-count hop-number Undo hops-count Undo label advertise Label-distributionLabel-distribution independent ordered Undo label-distribution Label-retention conservative liberal Label-retentionUndo label-retention Use the undo lsp-trigger command to restore the default Related command hops-count,path-vectorsLoop-detect Lsp-trigger Lsr-id # Configure the LDP LSR ID of LDP instance named vpn1Syntax lsr-idlsr-id Undo lsr-id Mpls Md5-passwordSyntax mpls Undo mpls # Enable Mpls for interface Ethernet 1/0 Related command mpls lsr-idMpls ldp system view View System view/interface view Mpls ldp interface view # Enable LDP for VPN instance vpn1Syntax mpls ldp Undo mpls ldp 1549 Mpls ldp advertisement dod du Mpls ldp advertisementUndo mpls ldp advertisement Related command remote-ip Mpls ldp timer hello-holdMpls ldp remote-peer Example # Create a remote peer entity named BJI Mpls ldp timer keepalive-hold Mpls lsr-id Mpls ldp transport-addressView Interface view/MPLS LDP remote peer view Syntax mpls lsr-id lsr-id Undo mpls lsr-id Related command display mpls interface Mtu-signallingSyntax mtu-signalling Undo mtu-signalling Example # Set the LSR ID to Path-vectors Related command loop-detect,hops-countPing lsp Syntax path-vectors pv-number Undo path-vectors Syntax remote-ip ip-address Undo remote-ip Remote-ip Reset mpls ldp Reset mpls fast-forwarding cacheRelated command mpls ldp remote-peer Reset mpls fast-forwarding cache Reset mpls statistics lsp Reset mpls statistics interfaceSyntax reset mpls statistics lsp index all name lsp-name Related command display mpls statistics lsp Snmp-agent trap enable mplsStatic-lsp egress Lsp-name Name for the LSP, a string of 1 to 15 characters Undo static-lsp ingress lsp-name Static-lsp ingress Undo static-lsp transit lsp-name Static-lsp transit1561 Statistics interval Related command static-lsp egress, static-lsp ingressTracert lsp Syntax tracert lsp -a source-ip-exp Ttl expiration Ttl expiration pop commandTtl expiration pop Undo ttl expiration pop Ttl propagate Add hop Mpls TE Configuration Commands Display explicit-path Delete hopSyntax delete hop ip-address Syntax display explicit-path pathname # Display the latest TE information advertised by IS-IS TE Display isis traffic-eng advertisements1567 Intf Addr Verbose Displays details Display isis traffic-eng link1569 Vpn-instance vpn-instance-name Specifies a VPN instance. Display isis traffic-eng network 1571 Display isis traffic-eng statistics Display isis traffic-eng sub-tlvs Related command te-set-subtlv Display mpls rsvp-te Label switched Router ID, Begin include exclude regular-expression Display mpls rsvp-te establishedAbout RSVP-TE globally or for an interface # Display RSVP-TE information for interface Ethernet 1/0 Filters output by regular expression Display mpls rsvp-te peerSpaces 1577 Display mpls rsvp-te psb-content Erhopstrict RSVP-TE requests on the specified or all interfaces Display mpls rsvp-te request1579 X.X Display mpls rsvp-te reservation 1581 Display mpls rsvp-te rsb-contentLSP ID Tunnel Dest 1583 Display mpls rsvp-te sender Global Display global RSVP-TE information Display mpls rsvp-te statisticsInterface is specified RSVP-TE is displayed 1585 # Display the RSVP-TE statistics of interface Serial 1/0 Ip-address prefix-length arguments Display mpls static-cr-lsp # Display detailed information about all static CR-LSPs Display mpls te cspf tedb1587 IGP # Display all Tedb information # Display the Tedb information of IGP area1589 Mpls LSR ID IGP # Display the Tedb information of all nodes # Display Tedb information for a specified interface address Links of all interfaces if no interface is specified Display mpls te link-administration admission-control Description on fields of the command Display mpls te link-administration bandwidth-allocation1593 Egress ingress remote transit name name incoming-interface Display mpls te tunnel 1595 # Display detailed information about Mpls TE tunnelsLSP-ID Lsr-id Ingress LSR ID, in dotted decimal notation Display mpls te tunnel path# Display the paths that all Mpls TE tunnels traverse Display mpls te tunnel-interface Display mpls te tunnel statisticsSyntax display mpls te tunnel statistics Syntax display mpls te tunnel-interface CR-LSP 1599 Display ospf mpls-te Area ID TE enabled Ospf area ID LSA Type Syntax display ospf process-id traffic-adjustment Display ospf traffic-adjustment1601 Syntax display tunnel-info tunnel-id all statistics Display tunnel-info# Display statistics about tunnels Enable traffic-adjustment advertise Enable traffic-adjustment# Enable IGP shortcut when the IGP protocol is IS-IS View Ospf view/IS-IS view List hop Explicit-path View Explicit path view Modify hop1605 Mpls rsvp-te authentication cipher plain auth-key Mpls rsvp-te authenticationUndo mpls rsvp-te authentication Mpls rsvp-te 1607 Mpls rsvp-te blockade-multiplier Mpls rsvp-te graceful-restart Related command mpls rsvp-te timer refreshMpls rsvp-te hello Syntax mpls rsvp-te hello Undo mpls rsvp-te hello Mpls rsvp-te hello-lost # Enable Rsvp hello extension on interface Ethernet 1/01609 Mpls rsvp-te keep-multiplier Related command mpls rsvp-te timer helloMpls rsvp-te reliability Example # Set the keep multiplier to five Mpls rsvp-te srefresh Mpls rsvp-te resvconfirm Mpls rsvp-te timer graceful-restart restart Mpls rsvp-te timer graceful-restart recovery Mpls rsvp-te timer refresh Mpls rsvp-te timer helloRelated command mpls rsvp-te hello, mpls rsvp-tehello-lost Example # Set the hello interval to five seconds Related command mpls rsvp-tekeep-multiplier Mpls rsvp-te timer retransmissionUndo mpls rsvp-te timer retransmission Mpls te # Enable Mpls TE on interface Ethernet 1/0Syntax mpls te Undo mpls te Mpls te affinity property Related command mpls te link administrative groupMpls te auto-bandwidth Undo mpls te auto-bandwidth Related command mpls te timer auto-bandwidth Mpls te backupMpls te backup hot-standby ordinary Undo mpls te backup With backup enabled, the record route Mpls te backup bandwidthExample # Enable hot backup on tunnel Mpls te bandwidth change thresholds Mpls te bandwidthMpls te bandwidth bc0 bc1 bandwidth Undo mpls te bandwidth Syntax mpls te commit Mpls te commitView Tunnel interface view Related command mpls te cspf Mpls te cspf timer failed-linkExample # Set the failed link timer to 50 seconds Mpls te cspf Mpls te fast-reroute bypass-tunnel Mpls te fast-rerouteSyntax mpls te fast-reroute Undo mpls te fast-reroute Description Example Mpls te igp advertise# Set the hold time to 10000 milliseconds 1623 Mpls te igp shortcut Mpls te igp metricMpls te igp shortcut isis ospf Undo mpls te igp shortcut Related command mpls te affinity property Mpls te link administrative groupMpls te loop-detection Syntax mpls te loop-detection Undo mpls te loop-detection Mpls te max-reservable-bandwidth Mpls te max-link-bandwidth Mpls te metric Related command mpls te path metric-typeUndo mpls te max-reservable-bandwidth Syntax mpls te metric value Undo mpls te metric Mpls te path explicit-path Related command mpls te metricMpls te path metric-type Example In Mpls view Mpls te record-route Mpls te priorityUndo mpls te priority Syntax mpls te record-route label Undo mpls te record-route Mpls te reoptimization tunnel interface view Mpls te reoptimization user viewMpls te reoptimization Mpls te retry Mpls te resv-style Example # Set the maximum number of tunnel setup retries to Related command mpls te timer retryExample # Enable route pinning Mpls te route-pinning Mpls te signal-protocol crldp rsvp-te static Mpls te signal-protocolMpls te tie-breaking Mpls te tie-breaking least-fill most-fill random By default, automatic bandwidth adjustment is disabled Mpls te timer auto-bandwidthRelated command mpls te auto-bandwidth Mpls te timer retry Mpls te timer fast-rerouteSyntax mpls te timer retry second Undo mpls te timer retry 1635 Examples # Configure the tunnel ID as Related command mpls te retryMpls te tunnel-id Mpls te vpn-binding Syntax mpls-te enable Undo mpls-te Mpls-te enableRelated command opaque-capability Next hop Opaque-capability Related command delete hop Reset mpls te auto-bandwidth adjustment timers Reset mpls rsvp-te statisticsSyntax reset mpls te auto-bandwidth adjustment timers Static-cr-lsp egress Static-cr-lsp ingress CR-LSP on the ingress or a transit node Static-cr-lsp transitUndo static-cr-lsp transit tunnel-name # Configure sub-TLVs for IS-IS process Use the undo te-set-subtlvcommand to restore the defaultBw-constraint Sets the bandwidth constraint sub-TLV Value Sub-TLV in the range 19 to Cost-style on If no level is specified, IS-IS TE applies to Level-1-2 Mpls TE Configuration Commands Ccc interface in-label out-label Mpls L2VPN Configuration Undo ce ce-name Ccc interface out-interface # Create a CE named ce2 for a VPN ConnectionView Mpls L2VPN CE view 1647 Display bgp l2vpn Related command route-distinguisher Mpls L2VPN viewTunnel select-seq load-balance-number on CE ID 1649 Verbose Peer Local 1651 Pref Preference Syntax display ccc ccc-name ccc-nametype local remote Display ccc# Display information about all local CCC connections # Display information about all CCC connections Down Display l2vpn ccc-interface vc-type Configured on the CE interface Configured on the routerDisplay mpls l2vc 1655 VC ID VC ID Vpn-name local-ce remote-ce Display mpls l2vpn # Display information about L2VPN vpn1 Description on the fields of the display mpls l2vpn command# Display information about local CEs of L2VPN vpn1 # Display information about remote CEs of L2VPN vpn1 Display mpls l2vpn connection1659 Status Status of the connection Peer-id Description on the fields of mpls l2vpn connection summary Display mpls static-l2vc Display mpls l2vpn forwarding-infoExample # Display Mpls L2VPN forwarding information Syntax l2vpn-family L2vpn-family1663 Mpls l2vc Related command tunnel select-seqload-balance-numberonUndo l2vpn-family Mpls l2vpn vpn-name Mpls l2vpnExample # Create a Martini Mpls L2VPN connection Syntax mpls l2vpn Undo mpls l2vpn # Create Kompella VPN named vpn2 and enter Mpls L2VPN view Mpls static-l2vc destinationUndo mpls static-l2vc Mtu Mpls L2VPN view Reset bgp l2vpnSyntax mtu mtu Example # Set the MTU for Kompella connections to Takes effect only when it is configured with an RD Re-create the VPN using the new RDRoute-distinguisher Mpls L2VPN view Route-distinguisher route-distinguisher Example # Associate VPN vpn1 with VPN targets Vpn-target Mpls L2VPN view1669 Mpls L2VPN Configuration Commands Default local-preference BGP-VPNv4 subaddress family view Apply access-vpn vpn-instanceSyntax default local-preference value View Policy routing view Default med BGP-VPNv4 subaddress family view Display bgp vpnv4 all routing-table Description VPN instance view1673 Example # Display all BGP VPNv4 routing information All Specifies all VPNv4 peers Display bgp vpnv4 group1675 Display bgp vpnv4 network Display bgp vpnv4 all vpn-instance vpn-instance-name paths Display bgp vpnv4 pathsBe displayed # Display all BGP VPNv4 AS path information Verbose Displays detailed information Display bgp vpnv4 peerVPNv4 peers 1679 # Display detailed information about BGP VPNv4 peer # Display all BGP VPNv4 peer information 1681 Display bgp vpnv4 route-distinguisher routing-table Example # Display the BGP VPNv4 routing information of RD Related command route-distinguisher VPN instance view1683 Fields of the above output All Specifies all VPNv4 peers Display bgp vpnv4 routing-table label1685 Display bgp vpnv4 vpn-instance routing-table 1687 Display fib vpn-instance Display fib statistics vpn-instanceDisplay fib statistics vpn-instance Display fib vpn-instance vpn-instance-name include string # Display detailed information about a VPN instance Display ip vpn-instance1689 Display ospf sham-link Related command sham-linkSyntax display ospf process-id sham-link area area-id Example # Display information about all Ospf sham links # Display information about Ospf sham links in area Display tunnel-policyDisplay tunnel-policy all policy-name tunnel-policy-name Tunneling policy or all tunneling policies Domain-id Example # Configure the Ospf domain ID# Display tunneling policy aaa Filter-policy export BGP-VPNv4 subaddress family view Export route-policy1693 Filter-policy import BGP-VPNv4 subaddress family view Ip binding vpn-instance Import route-policy1695 Ipv4-family Ip vpn-instanceView BGP view Vpnv4 Enters BGP-VPNv4 subaddress family view 1697 Peer advertise-community BGP-VPNv4 subaddress family view Peer as-path-acl BGP-VPNv4 subaddress family view Peer allow-as-loop 1699 Peer default-route-advertise vpn-instance Related command peer upe Peer enablePeer filter-policy BGP-VPNv4 subaddress family view 1701 Peer group Peer label-route-capability BGP view/BGP VPN instance view Peer ip-prefix BGP-VPNv4 subaddress family view 1703 Peer next-hop-invariable BGP-VPNv4 subaddress family view Peer public-as-only BGP-VPNv4 subaddress family view Peer next-hop-local 1705 Peer reflect-client Peer upe Peer route-policy BGP-VPNv4 subaddress family view Policy vpn-target Command applies to inter-provider VPN option B schemesSyntax policy vpn-target Undo policy vpn-target 1707 Reflector culster-id Reflect between-clients 1709 Refresh bgp vpn-instance Refresh bgp vpnv4 Reset bgp vpn-instance Reset bgp vpn-instance flap-info Reset bgp vpn-instance dampening1711 Route-distinguisher VPN instance view Reset bgp vpnv4Syntax route-distinguisher route-distinguisher Route-tag Then re-create the VPN instance and re-configure a new RDInstance Syntax route-tag tag-value Undo route-tag Routing-table limit Example # Configure the route tag for Ospf process 100 asImport-route Ospf view on Sham-link Rr-filterUndo rr-filter View Ospf area view Mpls L3VPN Configuration Commands Tnl-policy VPN instance view Related command tunnel select-seqload-balance-numberTunnel-policy Undo tnl-policy Tunnel select-seq load-balance-number Load-balance-number command can be usedUndo tunnel select-seq Vpn-target VPN instance view Vpn-instance-capability simpleView Ospf multi-instance view 1719 Mpls L3VPN Configuration Commands Authentication-algorithm VAM Server Configuration CommandsAuthentication-method Vam server vpn , authentication-method Display vam server address-map Vam server vpn , authentication-algorithm Syntax display vam server statistic all vpn vpn-name Display vam server statisticDescription on the fields of display vam server address-map 1723 # Display statistics of VPN domain 1 on the VAM server Example # Display statistics of the VAM server Encryption-algorithm Related command vam server vpnHub private-ip Undo hub private-ip private-ip-address Keepalive interval Related command vam server vpn, keepalive retry Keepalive retry Related command vam server vpn, keepalive intervalPre-shared-key VPN domain view Syntax keepalive retry retry-times Undo keepalive retry Syntax server enable Undo server enable Server enableRelated command vam server vpn, vam server enable Example # Enable the VAM server function of VPN domain Related command Vam server vpn, server enable Example Vam server enableVam server ip-address Syntax vam server vpn vpn-name Undo vam server vpn vpn-name Vam server vpn Client enable VAM Client Configuration CommandsRelated command vam client name, and vam client enable 100 Example # Display the status information of VAM client abc Pre-shared-key cipher simple key-string Pre-shared-key VAM client viewVAM client view Cipher Specifies a pre-shared key in cipher text Related command vam client name No pre-shared key is configured by defaultResend interval Syntax resend interval time-interval Undo resend interval Server secondary ip-address Server primary ip-address1735 By default, no local username or password is configured Vam client enableExample # Set the local username and password both to user User By default, no VAM client is configured Vam client name and client enableVam client name An interface Undo vpn VpnExample # Specify the VAM client abc to belong to VPN Related command ipsec profile system view Ipsec Profile Configuration Commands101 Display ipsec profile Ipsec profile system view Inbound ESP setting 1741 Ipsec Profile Configuration Commands 102 Dvpn Tunnel Configuration CommandsDisplay dvpn session Associated with the VAM client Dumb Dvpn session dumb-time Ipsec profile tunnel interface view Dvpn session idle-timeUndo ipsec profile ipsec-profile-name&1-6 1745 Undo keepalive Keepalive Tunnel-protocol dvpn udp Related command Interface tunnel on ExampleSyntax tunnel-protocol dvpn udp Undo tunnel-protocol Example # Configure the Dvpn tunnel mode Related command interface tunnel onVam client Syntax vam client client-name Undo vam client Related command interface tunneland source GRE Configuration Commands103 Down Example # Display information about interface Tunnel0 1751 Syntax gre checksum Undo gre checksum Gre checksum Gre key Related command interface tunnelUndo gre key 1753 Syntax interface tunnel number Undo interface tunnel number 1755 Syntax tunnel-protocol gre ipv6 Undo tunnel-protocol Tunnel-protocol gre 104 L2TP Configuration CommandsAllow l2tp Undo allow Related command Display l2tp tunnel Example Related command l2tp-groupDisplay l2tp session Sessions Syntax display l2tp tunnel Display l2tp tunnel1759 L2tp sendaccm enable L2tp enableRelated command allow l2tp Syntax l2tp enable Undo l2tp enable L2tp enable L2tpmoreexam enableUse the undo l2tp-group command to remove an L2TP group L2tp-group Related command Mandatory-lcp Example Related command allow l2tp and start l2tpMandatory-chap Mandatory-lcp Related command mandatory-chap Reset l2tp tunnelUndo mandatory-lcp View L2TP group view Related command display l2tp tunnel Tunnel authenticationSyntax tunnel authentication Start l2tp Tunnel avp-hidden Undo tunnel authenticationSyntax tunnel avp-hidden Undo tunnel avp-hidden 1765 Tunnel name Tunnel flow-control Tunnel timer hello Tunnel password L2TP Configuration Commands Description on the fields of the display qos car command Traffic Policing TP Configuration CommandsDisplay qos car interface Filed Description Display qos carl Description on the fields of the display qos carl commandQos car Display qos carl carl-index 1771 Undo qos carl carl-index Qos carl 1773 Examples # Configure Carl rule 1 with packet precedence Traffic Policing TP Configuration Commands Description on the fields of the display qos gts command Traffic Shaping Configuration Commands106 Display qos gts interface Undo qos gts any acl acl-number queue queue-number Qos gts 1777 Related commands acl on Traffic Shaping Configuration Commands Description on the fields of the display qos lr command Line Rate Configuration Commands107 Display qos lr interface Qos lr layer 2 interface view or port group view Qos lr interface viewUndo qos lr inbound outbound Interfaces is 4 or 9, this argument is not supported Layer 2 module interface view, port group view1781 Line Rate Configuration Commands 108 Defining Class CommandsDisplay traffic classifier Undo if-match not match-criteria If-matchClass view Match-criteria Class match rules. The values are as follow Value Description Rtp start-port 1785End-port Qos-local-id Define Mpls EXP precedence matching rule # Define a class to match ACL Related commands traffic classifier1787 # Define a class to match IPV6 ACL # Define a class to match the ACL named flow# Define a class to match the IPv6 ACL named flow # Define matching rule for all packets Traffic classifier tcl-name operator and or Traffic classifierUndo traffic classifier tcl-name Examples # Define a class named as class1 By default, the relation is operator 109 Defining Traffic Behavior CommandsCar Undo car Qos policy , traffic behavior , classifier behavior Display traffic behavior Gts FilterFilter deny permit Undo filter Undo gts RedirectUndo redirect View Traffic behavior view Syntax remark atm-clp atm-clp-value Undo remark atm-clp Remark atm-clp1795 Remark dscp Remark dot1pSyntax remark dot1p 8021p Undo remark dot1p Syntax remark dscp dscp-value Undo remark dscp Syntax remark fr-de fr-de-value Undo remark fr-de Remark fr-de1797 Remark mpls-exp Remark ip-precedenceExamples # Remark the DE bit in FR packets to Syntax remark mpls-exp exp-value Undo remark mpls-exp Traffic behavior Remark qos-local-id1799 Examples # Define a traffic behavior named behavior1 Related commands qos policy Defining Policy Commands110 Classifier behavior System-defined Policy pre-defined by the system Description on the fields of the display qos policy commandUser-defined Policy pre-defined by the user Tcl-name Class name in the policy 1803 Display qos policy interface EXP Qos apply policy interface view 1805 Qos apply policy layer 2 interface view or port group view Syntax qos policy policy-name Undo qos policy policy-name Qos policy 1807 Defining Policy Commands 111 Fifo Queuing Configuration CommandsQos fifo queue-length 1809 Fifo Queuing Configuration Commands Related commands qos pq PQ Configuration Commands112 Display qos pq interface Qos pq Related commands qos pq, qos pq pqlExamples # Display PQLs Syntax qos pq pql pql-index Undo qos pq Qos pql inbound-interface Qos pql default-queueExamples # Apply the priority list 12 to the Ethernet 1/0 1813 Qos pql protocol By default, no classification rule is configuredDescription on values of queue-key and key-value Queue-key Key-value Description 1815 Qos pql queue PQ Configuration Commands Related commands qos cq CQ Configuration Commands113 Display qos cq interface Qos cq Default values will not be displayedExamples # Display information about a CQL Syntax qos cq cql cql-index Undo qos cq Examples # Assign default queue 2 to CQL Qos cql default-queueQos cql inbound-interface 1819 Descriptions of values of queue-key and key-value Qos cql protocol 1821 Qos cql queue Undo qos cql cql-indexqueue queue-numberserving Qos cql queue servingExamples # Specify byte-count of queue 2 in the CQL 5 to Related commands qos wfq WFQ Configuration Commands114 Display qos wfq interface Undo qos wfq Qos wfqDisplay interface, display qos wfq interface 115 CBQ Configuration CommandsDisplay qos cbq interface Qos max-bandwidth Queue af 1827 Queue ef Queue wfq Wred Queue-lengthSyntax wred dscp ip-precedence Undo wred 1829 Undo wred dscp dscp-value Wred dscp 1831 Wred ip-precedence Wred weighting-constant Description on the fields of the display qos rtpq command RTP Priority Queue Configuration Commands116 Display qos rtpq interface Qos rtpq Qos rtpq 1835 Related commands qos reserved-bandwidth RTP Priority Queue Configuration Commands 117 QOS Token Configuration CommandsQos qmtoken Qos qmtoken token-number QOS Token Configuration Commands Related commands qos map-tabledot1p-Ip Priority Mapping Table Configuration Commands118 Display qos map-table Parameters in the default mapping table Related commands display qos map-tableQos map-table dot1p-Ip Import 1841 Priority Mapping Table Configuration Commands 119 Port Priority Configuration CommandsQos priority Undo qos priority Port Priority Configuration Commands 120 Port Priority Trust Mode Configuration CommandsDisplay qos trust interface Qos trust Port Priority Trust Mode Configuration Commands 121 Wred Configuration CommandsDisplay qos wred interface 1847 Qos wred dscp ip-precedence enable Qos wred enableUndo qos wred enable Dscp Uses the Dscp value for calculating drop probability Related commands qos wfq, display qos wred interface By default, the dropping method of a queue is tail dropQos wred dscp 1849 Discard-probability discard-prob Qos wred weighting-constantUndo qos wred ip-precedence ip-precedence Wred with the qos wred enable command on it Length, in the range 1 to 16. It defaults toQos wred enable, display qos wred interface Calculate the average length of Wred queues Wred Configuration Commands 122 Wred Table Configuration CommandsDisplay qos wred table Syntax display qos wred table table-name Qos wred queue table Qos wfq , qos wred enable , display qos wred interfaceQos wred apply Queue Related commands qos wred queue table in system view1855 Wred Table Configuration Commands 123 Mpls QOS Configuration CommandsIf-match mpls-exp Qos cql protocol mpls exp Qos pql protocol mpls exp Related commands qos cql protocol Examples # Set EXP value of remarked Mpls packet to Related commands qos pql protocol1859 Mpls QOS Configuration Commands 124 DAR Configuration CommandsDar max-session-count Dar protocol Protocol name Protocol type Pre-defined port number Protocols of pre-defined ports 1863 Dar protocol-rename # Restore the default name of the user-defined01 protocolDar protocol-statistic Undo dar protocol-rename user-defined-name Undo dar protocol-statistic Display dar informationSyntax display dar information 1865 Display dar protocol all protocol-name Display dar protocol 1867 Display dar protocol-rename Display dar protocol-rename Display dar protocol-statistic If-match protocol If-match protocol http If-match protocol rtp Reset dar protocol-statisticUndo if-match not protocol rtp payload-type audio video Reset dar session Information, i.e. to restore the statistics toAll Deletes all statistics information # Deletes all statistics information DAR Configuration Commands 125 FR QOS Configuration CommandsApply policy outbound # Define a traffic behavior named behavior Cbs Related commands ebs, cir allow, cirCir Undo cir Cir allow Related commandsCbs, ebs, cir allow Cir allow inbound outbound committed-information-rate Related commands fr congestion-threshold Related commands cbs, ebs, cirCongestion-threshold Undo cq Display fr class-map Related commands wfq, pq, fr pvc-pq1879 Display fr fragment-info Related commands fragment 1881 # Display FR fragment information of a certain interfaces Fr switch Display fr switch-table 1883 PVC PQ on FR interface Display qos pvc-pq interface# Display PVC PQ information on FR interface Serial2/0 Ebs Related commands Cbs, cir allow, cir ExamplesFifo queue-length Related commands fr-class Related commands fr classFr class Fr congestion-threshold Fr de del Related commands congestion-threshold1887 Related commands fr de del, fr del protocol Related commands fr del inbound-interface,fr del protocolFr del inbound-interface Fr del protocol Related commands fr de del, fr del inbound-interfaceProtocol ip IP 1889 Fr pvc-pq Related commands pvc-pqUndo fr pvc-pq Fr traffic-policing Related commands fr class, fr-class,fr dlciFr traffic-shaping Syntax fr traffic-policing Undo fr traffic-policing Fragment Examples # Enable Frts on the serial interface Serial 1/0Fr-class Undo fragment fragment-size Related commands cq, wfq, fr pvc-pq Related commands fr class, fr dlciPvc-pq Undo pq Undo pvc-pq RtpqFr pvc-pq Number, in the range 2000 to Traffic-shaping adaptation Related commands fr traffic-shaping,cir allow, and cirUndo traffic-shaping adaptation becn interface-congestion Wfq Related commands cq, pq, fr pvc-pqUndo wfq Examples # Apply WFQ to the FR class test1 Example # Display 802.1x configuration information 802.1X Configuration Commands126 Display dot1x Descriptions on the fields of the display dot1x command Dot1x interface interface-list Dot1xUndo dot1x interface interface-list Dot1x Related command display dot1x Dot1x authentication-method# Enable 802.1x globally Syntax dot1x authentication-method chap eap pap Dot1x guest-vlan Undo dot1x authentication-method Dot1x guest-vlan vlan-id Undo dot1x guest-vlan Dot1x handshake Dot1x handshakeUndo dot1x handshake Undo dot1x max-user interface interface-list Dot1x max-userDot1x max-user user-number Undo dot1x max-user Dot1x multicast-trigger By default, the multicast trigger function is enabledDot1x port-control Dot1x port-method macbased portbased Undo dot1x port-method Dot1x port-method Syntax dot1x quiet-period Undo dot1x quiet-period Dot1x quiet-period1907 Dot1x retry Related command display dot1x, dot1x timerDot1x supp-proxy-check Undo dot1x retry 1909 Dot1x timer Example # Set the server timeout timer to 150 seconds Reset dot1x statisticsReset dot1x statistics interface interface-list 1911 Example # Clear 802.1x statistics on port Ethernet 1/1 Access-limit AAA Configuration CommandsAccounting default 127 AAA Configuration Commands Accounting login Accounting lan-accessRelated command accounting default, radius scheme 1915 Accounting optional Undo accounting loginSyntax accounting optional Undo accounting optional 1917 Accounting portal Accounting ppp Undo attribute access-limit idle-cut ip location mac vlan Related command domain, radius schemeAccounting voip Attribute Related command display local-user Authentication defaultLocal Performs local authentication Example # Set the IP address of local user user1 to Undo authentication lan-access Authentication lan-accessLocal Performs local authentication None Does not perform any authentication Related command authentication default, radius scheme Authentication login 1923 Authentication portal Undo authentication ppp Authentication pppRadius-scheme radius-scheme-name local Authorization command Authentication voip1925 Related command authorization default, hwtacacs scheme Authorization default 1927 Authorization lan-access Related command authorization default, radius scheme Authorization login 1929 Authorization portal Authorization voip Authorization pppUndo authorization ppp Authorization default , hwtacacs scheme , radius scheme Domain , radius scheme Cut connection Display connection Description on the fields of the display connection command Related command cut connection ExampleDisplay domain # Display information about all AAA user connections Description on the fields of the display domain command Related command access-limit,domain, state Display local-user Related command local-user # Display information about all local users DomainUndo domain isp-name Description on the fields of display local-user Related command access-limit,state, display domain Domain defaultDomain default disable enable isp-name State , display domain Ip pool Idle-cutDomain Domain aabbcc.net Level Related command remote address onSyntax level level Undo level Local-user Related command display local-user,service-typeExample # Set the level of user user1 to Example # Add a local user named user1 Password Local-user password-display-modeRelated command display local-user , password Self-service-url Service-type Service-type ppp Service-type ftpRelated command service-type ppp and service-type ftp Syntax service-type ftp Undo service-type ftp State active block State Work-directory Related command domain# Place the current user user1 to the state of blocked Syntax work-directory directory-name Undo work-directory 1947 AAA Configuration Commands Accounting-on enable Radius Configuration Commands128 Radius scheme Accounting-on enable send Accounting-on enable intervalRelated command radius scheme, accounting-on enable Gigabyte Data-flow-format Radius scheme viewMega-packet, or giga-packet Packets to be sent to a Radius server Related command radius scheme Related command display radius schemeExample # Display the configurations of all Radius schemes Display radius scheme Display radius statistics Display radius statisticsExample # Display statistics about Radius packets 1953 State statistictotal=1024 State statistics Dead 1955 Which is a string of 1 to 32 characters Display stop-accounting-bufferTime range, or user name On August 31 Nas-ip Radius scheme view Key Radius scheme viewDisplay radius scheme Primary accounting Radius scheme view Related command radius nas-ipUndo primary accounting 1959 Primary authentication Radius scheme view Example # Enable the listening port of the Radius client Syntax radius client enable Undo radius clientRadius client Radius nas-ip Radius scheme Related command nas-ip Radius scheme viewUndo radius nas-ip Undo radius scheme radius-scheme-name Radius trap Reset stop-accounting-buffer Reset radius statisticsSyntax reset radius statistics Example # Clear Radius statistics Undo retry Retry 1965 Retry realtime-accounting Secondary accounting Radius scheme view Retry stop-accounting Radius scheme viewUndo secondary accounting 1967 Secondary authentication Radius scheme view Server-type Security-policy-serverSyntax server-type extended standard Undo server-type View Radius scheme view Primary Sets the status of the primary Radius server Use the state command to set the status of a Radius serverSecondary Sets the status of the secondary Radius server Accounting Sets the status of the Radius accounting server Stop-accounting-buffer enable Radius scheme view Timer realtime-accounting Radius scheme view Timer quiet Radius scheme viewSyntax timer quiet minutes Undo timer quiet 1971 Related command retry realtime-accounting,radius scheme Timer response-timeout Radius scheme viewNumber of users Real-time accounting interval minute User-name-format Radius scheme view Related command radius scheme, retryUser-name-format with-domain without-domain Radius Configuration Commands Related command display hwtacacs Hwtacacs Configuration Commands129 Data-flow-format Hwtacacs scheme view Description on the fields of the display hwtacacs command Related command hwtacacs scheme Scheme view , retry stop-accounting Hwtacacs scheme view Hwtacacs nas-ipAddress or a loopback address Hwtacacs scheme Related command nas-ip Hwtacacs scheme viewUndo hwtacacs scheme hwtacacs-scheme-name Undo key accounting authentication authorization string Key accounting authentication authorization stringKey Hwtacacs scheme view Nas-ip Hwtacacs scheme view Primary accounting Hwtacacs scheme view Related command hwtacacs nas-ip Example # Set the primary authentication server Primary authentication Hwtacacs scheme view1981 Reset hwtacacs statistics Primary authorizationUndo primary authorization Accounting Clears Hwtacacs accounting statistics Retry stop-accounting Hwtacacs scheme view Syntax secondary authentication ip-address port-number Secondary authentication Hwtacacs scheme viewSecondary accounting Hwtacacs scheme view Example # Configure the secondary authentication server Secondary authorization1985 Example # Configure the secondary authorization server Stop-accounting-buffer enable Hwtacacs scheme viewView Hwtacacs scheme view Timer realtime-accounting Hwtacacs scheme view Timer quiet Hwtacacs scheme view1987 Timer response-timeout Hwtacacs scheme view Hwtacacs scheme User-name-format Hwtacacs scheme view Hwtacacs Configuration Commands Switch running a routing protocol Packet Filter Firewall Configuration CommandsDisplay firewall ethernet-frame-filter All Displays all the firewall statistics information Syntax firewall default permit deny Firewall defaultDisplay firewall-statistics Fragments-inspect Firewall enable Firewall enableUndo firewall enable Firewall ethernet-frame-filter Firewall fragments-inspect Example # Enable fragments inspection Firewall fragments-inspect high low Firewall fragments-inspect high low number defaultFirewall ipv6 fragments-inspect Undo firewall fragments-inspect high low Firewall packet-filter Related command firewall fragments-inspect Firewall packet-filter ipv6 Reset firewall ethernet-frame-filterOutbound Undo firewall packet-filter ipv6 inbound outbound Example # Clear all the firewall statistic information Reset firewall-statistics# Clear the firewall statistic information of Ethernet 1/0 131 Aspf Configuration CommandsAging-time Aging-time syn fin tcp udp seconds # Set the UDP idle timeout period to 110 seconds # Set the TCP idle timeout period to 3000 secondsAspf-policy Syntax display aspf all Display aspf all2001 Syntax display aspf interface Display aspf interface Display aspf session Display aspf policySyntax display aspf policy aspf-policy-number Display aspf session verbose Display port-mapping Firewall aspf Related command port-mappingExample # Display all the information about port mapping 2005 Syntax log enable Undo log enable Log enableExample # Enable the session logging function of the Aspf Port-mapping Related command display port-mapping Reset aspf sessionSyntax reset aspf session Example # Map port 3456 to the FTP protocol Aspf Configuration Commands Display mac-authentication MAC Authentication Configuration CommandsSyntax display mac-authentication interface interface-list DFIC-9FSW and MSR 20 Series Products MAC Addr Mac-authentication 2011 Mac-authentication domain Related command display mac-authentication Mac-authentication timer Mac-authentication user-name-format Reset mac-authentication statistics Connection-limit default action NAT Configuration CommandsConnection-limit default amount 133 Connection-limit enable Connection-limit enableUndo connection-limit enable Connection-limit policy Example # Create a connection-limit policy numbered Display connection-limit policySyntax display connection-limit policy policy-numberall 2017 Display connection-limit statistics Display nat address-group Display nat address-groupView Any view Parameter None Information Display nat all Display nat aging-timeDisplay nat aging-time Different NAT sessions 2021 Description on some fields of the display nat all command Destination address Display nat connection-limit Mask-length The length of net mask, in the range 1 to Display nat logSyntax display nat log 2023 Description on the fields of the display nat log command # View the NAT log configurationDisplay nat outbound Display nat outbound Display nat session Display nat serverSyntax display nat server Example # Display the active NAT sessions Display nat statisticsSyntax display nat statistics Limit acl Display userlog export Syntax limit mode amount Undo limit mode Limit modeView Connection-limit policy view Nat aging-time Nat address-groupUndo nat address-group group-number Tcp-syn udp seconds Nat alg 2031 Nat connection-limit-policy Nat log flow-active Nat log enable Nat outbound Nat log flow-beginNat log flow-begin Undo nat log flow-begin NAT Configuration Commands Nat outbound static # Configure the address poolNat server Syntax nat outbound static Undo nat outbound static NAT Configuration Commands 2037 Nat static # Remove the WWW server using the following commands Syntax reset nat session Reset nat session2039 Reset userlog nat logbuffer Reset userlog exportRelated command display userlog export Userlog nat export host Related command userlog nat export host Related command userlog nat export source-ipUserlog nat export source-ip 2041 Userlog nat syslog Userlog nat export versionSyntax userlog nat syslog Undo userlog nat syslog 134 PKI Configuration Commands Syntax ca identifier name Undo ca identifier Ca identifier Certificate request from Certificate request entityPki entity Simple password * manual Certificate request modeUndo certificate request mode Certificate request polling Certificate request url Related command display pki certificateUndo certificate request polling count interval 2047 Country Common-nameSyntax common-name name Undo common-name Undo country Crl check disable enable Crl update-periodCrl update-period hours Undo crl update-period Display pki certificate Crl urlUndo crl url 2051 Example # Display the local certificate Display pki certificate attribute-group Display pki certificate access-control-policy Display pki crl domain Related command pki retrieval-crl domain and pki domainSyntax display pki crl domain domain-name Example # Display the locally saved CRLs Ip PKI entity view FqdnUndo fqdn Undo ip Locality Ldap-serverUndo ldap-server Undo locality Organizational-unit OrganizationSyntax organization org-name Undo organization Pki certificate attribute-group Pki certificate access-control-policy2057 Pki domain Pki delete-certificateSyntax pki domain domain-nameundo pki domain domain-name Pki import-certificate Pki entityPki entity entity-name Undo pki entity entity-name Pki request-certificate domain Related command pki domain Pki retrieval-certificate Related command Pki domain ExamplePki retrieval-crl domain Pki retrieval-certificate ca local domain domain-name Root-certificate fingerprint Pki validate-certificatePki validate-certificate ca local domain domain-name Root-certificate fingerprint md5 sha1 string Syntax rule id deny permit group-name Undo rule id all Rule access control policy view2063 Undo state Portal authentication Portal Configuration Commands135 Display portal acl Display portal connection statistics Description on the fields of the display portal acl commandAll Displays portal connection statistics on all interfaces Statistics on the specified interface 2067 Display portal free-rule Msgauthenack Msgauthorack Msgloginack MsglogoutackSyntax display portal free-rule rule-number Display portal interface Related command portal free-rule2069 Display portal server Related command portal serverSyntax display portal server server-name URL All Displays portal server statistics on all interfaces Display portal server statistics2071 Reqchallenge Syntax display portal tcp-cheat statistics Display portal tcp-cheat statistics Specified interface enabling portal Display portal userSpecified interface or all interfaces enabling portal 2073 Undo portal auth-network network-addressall Portal auth-network Portal delete-user Related command display portal userPortal free-rule Undo portal free-rule rule-numberall Portal resource-name Related command display portal free-rule Portal server Related command display portal serverUndo portal server server-name key port url 2077 Portal server method Reset portal connection statistics Reset portal tcp-cheat statistics Reset portal server statisticsReset portal tcp-cheat statistics Portal Configuration Commands 136 RSH Configuration CommandsRsh INSTALL.LOG Description on the fields of the display time-range command Common Configuration CommandsDisplay time-range Time-range Common Configuration Commands 2085 Common Configuration Commands 138 IPV4 ACL Configuration CommandsAcl 2087 # Create IPv4 ACL 2002, giving the ACL a name of flow Acl copy# Delete the IPv4 ACL with the number # Delete the IPv4 ACL named flow Syntax acl name acl-name Acl name2089 # Define the description of IPv4 ACL Description for IPv4# Define the description of ACL Display acl Description on the fields of the display acl commandSyntax display acl acl-numberall name acl-name 2091 Syntax reset acl counter acl-number all name acl-name Reset acl counterRule in basic IPv4 ACL view # Clear statistics about IPv4 ACL flow 2093 Rule in advanced IPv4 ACL view TCP/UDP-specific parameters for advanced IPv4 ACL rules Icmp message Type Code Parameter Function Description Icmp-type Undo rule rule-id Rule in Ethernet frame header ACL view2097 View User-defined ACL view Rule in user-defined ACL view Rule comment for IPv4 Support to this command varies by device# Create a user-defined ACL rule Syntax rule rule-idcomment text Undo rule rule-idcomment # Create a rule in ACL 3000 and define the rule description Step for IPv4# Create a rule in ACL 4000 and define the rule description # Create a rule in ACL 5000 and define the rule description 2101 Example # Set the rule numbering step to 2 for ACL IPV4 ACL Configuration Commands 139 IPV6 ACL Configuration CommandsAcl ipv6 2103 # Create IPv6 ACL 2002, giving the ACL a name of flow Acl ipv6 copy# Delete the IPv6 ACL with the number # Delete the IPv6 ACL named flow Syntax acl ipv6 name acl6-name Acl ipv6 name2105 Display acl ipv6 Description for IPv6# Create a description for IPv6 ACL Syntax display acl ipv6 acl6-numberall name acl6-name All All basic and advanced IPv6 ACLs Reset acl ipv6 counter2000 to 2999 for basic IPv6 ACLs 3000 to 3999 for advanced IPv6 ACLs # Clear the statistics about the IPv6 ACL named flow Rule in basic IPv6 ACL viewUndo rule rule-id fragment logging source time-range 2109 Rule in advanced IPv6 ACL view Destination dest Parameter Function Description Source sourceTime-range time-name ICMPv6-specific match criteria for advanced IPv6 ACL rules TCP/UDP-specific match criteria for advanced IPv6 ACL rulesAvailable ICMPv6 messages Rule in simple IPv6 ACL view Parameters for simple IPv6 ACL rules View Simple IPv6 ACL view ICMPv6-specific parameters for simple IPv6 ACL rules TCP/UDP-specific parameters for simple IPv6 ACL rulesICMPv6 messages definable in simple IPv4 ACL rules Rule comment for IPv6 Support for this command varies by device2115 Example # Set the rule numbering step to 2 for IPv6 ACL Step for IPv6 2117 # Set the rule numbering step to 2 for IPv6 ACL IPV6 ACL Configuration Commands Ah authentication-algorithm Ipsec Configuration CommandsCryptoswitch fabric enable 140 Syntax display encrypt-card fast-switch Display encrypt-card fast-switch Display ipsec policy brief name policy-name seq-number Display ipsec policyIpsec policy system view # Display detailed information about all IPSec policies IPSec policy template group Display ipsec policy-template10000 Template group Display ipsec proposal Related command ipsec proposalDisplay ipsec sa Syntax display ipsec proposal proposal-name Reset ipsec sa, ipsec sa global-duration Description on the fields of the display ipsec sa command Display ipsec session Related command reset ipsec sessionSyntax display ipsec session tunnel-id integer Example # Display information about all IPSec sessions Display ipsec statistics Related command reset ipsec statisticsSyntax display ipsec statistics Example # Display IPSec packet statistics Syntax display ipsec tunnel Display ipsec tunnel2129 Encapsulation-mode Encrypt-card fast-switch Related command display encrypt-cardfast-switch Esp authentication-algorithmEsp encryption-algorithm Syntax esp encryption-algorithm 3des aes key-length des Undo esp encryption-algorithm Ike-peer IPSec policy view/IPSec policy template viewSyntax ike-peer peer-name Undo ike-peer peer-name Ipsec binding policy Related command ipsec policy-template2133 Syntax ipsec cpu-backup enable Undo ipsec cpu-backup enable Ipsec cpu-backup 2135 Ipsec policy interface view Syntax ipsec policy policy-nameseq-number isakmp manual Ipsec policy system view Ipsec policy-template Ipsec policy isakmp templateUndo ipsec policy-template template-name seq-number 2137 Related command display ipsec proposal Related command display ipsec policy-templateIpsec proposal Ipsec sa global-duration Related command sa duration, display ipsec sa durationIpsec session idle-time Example # Create an IPSec proposal named newprop1 Undo ipsec session idle-time PfsPfs dh-group1 dh-group2 dh-group5 dh-group14 Undo pfs Related command ipsec proposal, ipsec policy system view Example # Enable and configure PFS for IPSec policy policy1Proposal Undo proposal proposal-name Reset ipsec sa Reset encrypt-card fast-switchSyntax reset encrypt-card fast-switch Related command display ipsec sa Reset ipsec sessionSyntax reset ipsec session tunnel-id integer Sa authentication-hex Reset ipsec statisticsRelated command display ipsec session Syntax reset ipsec statistics View IPSec policy view/IPSec policy template view Sa duration2145 Sa encryption-hex 2147 Sa spi Sa string-key Security acl Example # Configure IPSec policy policy1 to reference ACLSyntax security acl acl-number Undo security acl 2149 Transform Example # Configure IPSec proposal prop1 to use AHTunnel local Syntax transform ah ah-esp esp Undo transform 2151 Tunnel remote Example # Set the remote address of the IPSec tunnel to 141 IKE Configuration CommandsIke proposal, display ike proposal Certificate domain Related command ike proposal, display ike proposalDh group1 group2 group5 group14 Undo dh Display ike dpd Related command ike dpdExample # Specify 768-bit Diffie-Hellman for IKE proposal Syntax display ike dpd dpd-name Display ike peer Related command ike peer system viewDisplay ike proposal Syntax display ike peer peer-name Related command ike proposal, ike peer system view Example # Display the settings of IKE proposalsDisplay ike sa 2157 # Display detailed information about the current IKE SAs 2159 Undo dpd DpdEncryption-algorithm 3des-cbc aes-cbc key-length des-cbc Exchange-mode Related command Id-type ExampleId-type Ike local-name Ike dpdExample # Use the ID type of name in IKE negotiation Syntax ike dpd dpd-name Undo ike dpd dpd-name Related command remote-name,id-typename Ike next-payload check disabledExample # Configure the local gateway name as app 2163 Ike peer system view Related command display ike proposalIke proposal Syntax ike peer peer-name Undo ike peer peer-name Ike sa keepalive-timer timeout Ike sa keepalive-timer intervalRelated command ike sa keepalive-timer timeout Example # Set the keepalive interval to 200 seconds Related command ike sa keepalive-timer interval Ike sa nat-keepalive-timer intervalExample # Set the keepalive timeout to 20 seconds Interval-time Local-address Local Syntax nat traversal Undo nat traversal Nat traversalPeer multi-subnet single-subnet Undo peer Pre-shared-key Related command authentication-algorithmonRemote-address Syntax pre-shared-key key Undo pre-shared-key Related command id-typeip, local-address Reset ike saRelated command id-type,ike local-name Remote-name Example # Clear the IPSec tunnel to Related command display ike saSyntax sa duration seconds Undo sa duration 2171 Time-out Related command ike proposal and display ike proposalSyntax time-out time-out Undo time-out 142 SSH2.0 Configuration CommandsDisplay public-key local Public-key local create Example Display public-key peer brief name publickey-name Display public-key peerBrief Displays brief information about all public keys Specified or all public keys Display sftp client source Related command sftp client source# Display brief information about all public keys Syntax display sftp client source Display ssh client source Related command ssh client sourceDisplay ssh server Syntax display ssh client source # Display the session information of the SSH server Display ssh server-infoSyntax display ssh server-info 2177 Display ssh user-information Related command ssh userSyntax display ssh user-information username Example # Display information about all SSH users Peer-public-key end Related command Public-key peer ExamplePublic-key-code begin Peer-public-key end Public-key local create Public-key-code endPublic-key-code end Public-key peer, public-key-code begin Public-key local destroy, display public-key local Example Public-key local destroy# Create local RSA key pair # Create local DSA key pair Public-key local export rsa Related command public-key local createPublic-key local export rsa openssh ssh1 ssh2 filename Public-key local create , public-key local destroy # Display the RSA local public key in OpenSSH format Public-key local export dsaPublic-key local export dsa openssh ssh2 filename # Export the DSA local public key in OpenSSH format Public-key peer Related command public-key-code begin, public-key-code end# Display the DSA local public key in OpenSSH format Syntax public-key peer keyname Undo public-key peer keyname Sftp Public-key peer import sshkey2185 Undo sftp client ipv6 source Sftp client ipv6 sourceIpv6 ipv6-address Specifies a source IPv6 address Sftp client source Related command Display sftp client source ExampleSftp ipv6 Sysname sftp ipv6 Input Username Sftp server idle-timeout Sftp server enableSyntax sftp server enable Undo sftp server enable Related command display ssh server Ssh client first-time enable Ssh client authentication server Ssh client ipv6 source To access the SSH serverSsh client source Undo ssh client ipv6 source Related command display ssh client source Ssh server authentication-retries Ssh server compatible-ssh1x enable Ssh server authentication-timeoutBy default, the authentication timeout period is 60 seconds Example # Enable the SSH server to work with SSH1.x clients Syntax ssh server enable Undo ssh server enable Ssh server enableSsh server rekey-interval Undo ssh user username Ssh user2195 Ssh2 Related command display ssh user-information 2197 Ssh2 ipv6 SSH2.0 Configuration Commands 2199 SSH2.0 Configuration Commands 143 Sftp Configuration CommandsBye Syntax bye Delete CdupDir Syntax cdup Get ExitSyntax exit 2203 Help Put Mkdir2205 Quit PwdSyntax pwd Syntax quit Rename RemoveRmdir 2207 Sftp-client rmdir temp1 Directory successfully removed 144 SSL Configuration CommandsCiphersuite View SSL server policy view Syntax client-verify enable Undo client-verify enable Client-verify enableExample # Set the SSL connection close mode to wait Close-mode wait Display ssl server-policy Display ssl client-policySyntax display ssl client-policy policy-nameall Syntax display ssl server-policy policy-nameall Syntax handshake timeout time Undo handshake timeout Handshake timeoutPki-domain Syntax pki-domain domain-name Undo pki-domain Prefer-cipherUndo prefer-cipher 2213 Undo session cachesize timeout Session cachesize size timeout timeSession Rsaaes128cbcsha Ssl server-policy Ssl client-policy2215 Version ssl3.0 tls1.0 Use the undo version command to restore the defaultSSL client policy view Ssl3.0 Specifies SSL Display standby flow Backup Center Configuration CommandsSyntax display standby flow Display standby state Main and backup interfacesDisplay standby state Following tables describe the meanings of each state Backup flags Backup states of the backup interfaceStandby bandwidth Syntax standby bandwidth size Undo standby bandwidth Standby interface Related command standby interface Standby threshold Related commands standby trackUndo standby threshold 2221 Related command standby interface and standby bandwidth Standby timer delayUndo standby timer delay Standby track Standby timer flow-checkUndo standby track 2223 Standby interface, track on Display vrrp IPV4-BASED Vrrp Configuration Commands Vrrp vrid track interface command Description on the fields of the display vrrp commandVrrp vrid track command Display vrrp statistics 2227 Example # Display the statistics about all standby groups Vrrp vrid authentication-mode Reset vrrp statistics255 Device are cleared Syntax vrrp method real-mac virtual-mac Undo vrrp method Vrrp method2229 Vrrp ping-enable Vrrp ping-enableUndo vrrp ping-enable Addresses of standby groups Vrrp un-check ttl Default mode is immediate preemption without delayVrrp vrid preempt-mode Syntax vrrp un-check ttl Undo vrrp un-check ttl Vrrp vrid priority Vrrp vrid track Vrrp vrid timer advertise2233 Vrrp vrid track interface 2235 Vrrp vrid virtual-ip # Add virtual IP address 10.10.10.11 to standby group 147 Vrrp Configuration Commands For IPV6Display vrrp ipv6 IPv6 Display vrrp ipv6 statistics Vrrp ipv6 vrid track command 2239 Vrrp ipv6 method Reset vrrp ipv6 statisticsSyntax vrrp ipv6 method real-mac virtual-mac Vrrp ipv6 ping-enable Vrrp ipv6 ping-enableUndo vrrp ipv6 ping-enable Undo vrrp ipv6 method Vrrp ipv6 vrid preempt-mode Vrrp ipv6 vrid authentication-mode Undo vrrp ipv6 vrid virtual-router-idpriority Vrrp ipv6 vrid priority2243 Undo vrrp ipv6 vrid virtual-router-idtimer advertise Vrrp ipv6 vrid timer advertise 2245 Vrrp ipv6 vrid track Vrrp ipv6 vrid virtual-ip # Configure the virtual IPv6 address of standby group 1 as 148 Device Management Commands Buzzer enable BootromSyntax buzzer enable Undo buzzer enable Part This command is applicable on MSR 50 series routers only Display boot-loaderDisplay boot-loader slot slot-number Related command Boot-loader Display cpu-usage task number offset verbose from-device Display cpu-usage Display device Description on fields of the display boot-loader commandSyntax display device cf-card usb slot slot-numberverbose 2251 Usb Displays information of a universal serial bus USB Cf-card Displays information of a compact Flash CFVaries with devices Such as card, CF, USB, VCPM, VPM and DSP 2253 Description on fields on the display device commandCpld Display device manuinfo slot slot-number Display device manuinfoInformation about the device Display Display environment # Display the temperature information of cardsExample # Display manufacturing information of a device Display environment Display license Display fanDisplay fan fan-id Display license Syntax display power power-id Display powerDisplay memory Syntax display memory Display schedule reboot Display reboot-typeDisplay reboot-type slot slot-number Display schedule reboot Only users at management level can execute this command RebootReboot slot slot-number License register Use the remove command to remove a card Reset unused porttagSyntax reset unused porttag Remove slot slot-number Syntax schedule reboot at hhmm date Undo schedule reboot Schedule reboot at2261 Syntax schedule reboot delay hhmm mm Undo schedule reboot Schedule reboot delay 2263 Temperature-alarm enable Undo temperature-limit slot-number Temperature-limit Data-fill NQA Client Configuration CommandsSyntax data-fill string Undo data-fill Description any NQA test type view Data-sizeSyntax data-size size Undo data-size Destination port Destination ipSyntax destination ip ip-address Undo destination ip Syntax destination port port-number Undo destination port Display nqa Syntax display nqa result history admin-nameoperation-tagResult Displays the results of the last test History Displays the history records of a test 2269 Description on the fields of the display nqa result command Field Description Index History record number # Display the history records of tests Frequency FilenameSyntax filename filename Undo filename Syntax frequency interval Undo frequency Syntax history-records number Undo history-records History-records Next-hop Http-versionHttp-version Undo http-version Syntax nqa agent enable Undo nqa agent enable Nqa agent enableRelated command nqa server enable Nqa Nqa agent max-concurrent Example # Enable the NQA clientNqa schedule 2275 Operation Http test type view Operation FTP test type viewOperation get put Undo operation Syntax password password Undo password Password FTP test type viewOperation interface Undo operation interface Syntax probe count times Undo probe count Probe count Probe packet-number Probe packet-interval2279 Probe timeout Probe packet-timeoutSyntax probe timeout timeout Undo probe timeout 2281 Reaction Route-option bypass-route Reaction trapUndo reaction trap probe-failure test-complete test-failure Source interface Related command source ipUndo source interface 2283 Source ip Related command source interfaceSource port Syntax source ip ip-address Undo source ip Ttl TosSyntax tos value Syntax ttl value Type Username FTP test type view UrlSyntax url url Undo url Syntax vpn-instance instance Undo vpn-instance Vpn-instance ICMP-echo test type view 150 NQA Server Configuration CommandsDisplay nqa server status Syntax display nqa server status Syntax nqa server enable Undo nqa server enable Nqa server enableRelated command nqa server tcp-connect,nqa server udp-echo Example # Enable the NQA server Undo nqa server udp-echo ip-addressport-number Nqa server udp-echo2291 Sysname nqa server udp-echo 169.254.10.2 Display ip netstream cache Netstream Configuration CommandsSyntax display ip netstream cache Display ip netstream export Ip netstream statistics commandDisplay ip netstream export Exported NetStream UDP packets Syntax enable EnableUndo enable Related command ip netstream aggregation Source-prefix Ip netstream aggregation Ip netstream export source Ip netstream export hostExample # Enter NetStream AS aggregation view 2297 Ip netstream export version Related command ip netstream timeout inactive Ip netstream timeout activeIp netstream max-entry 2299 Reset ip netstream statistics Ip netstream timeout inactiveRelated command ip netstream timeout active Reset ip netstream statistics Display ntp-service sessions NTP Configuration CommandsSyntax display ntp-service sessions verbose 152 Display ntp-service status Display ntp-service statusExample # View the NTP service status information Syntax display ntp-service trace Display ntp-service trace2303 Undo ntp-service access peer query server synchronization Ntp-service accessProtection. a more secure method is identity authentication Sure you have already created and configured this ACL Ntp-service authentication-keyid Ntp-service authentication enableBy default, NTP authentication is disabled # Enable NTP authentication Ntp-service broadcast-server Ntp-service broadcast-client 2307 Ntp-service in-interface disable Ntp-service multicast-client Ntp-service max-dynamic-sessions Ntp-service refclock-master Ntp-service multicast-serverUndo ntp-service multicast-server ip-address 2309 Ntp-service source-interface Ntp-service reliable authentication-keyidUndo ntp-service source-interface Used as a reference clock Ntp-service unicast-peer Vpn-instance-name in your command Ntp-service unicast-serverPublic network Designated for the device No NTP server is designated for the device by defaultInterface and the NTP server coexist in this VPN 2313 NTP Configuration Commands Display rmon alarm Rmon Configuration CommandsSyntax display rmon alarm entry-number Related command rmon alarm Example # Display the configuration of Rmon event table Related command rmon eventDescription on the fields of the display rmon event command Display rmon event Display rmon history Display rmon eventlogSyntax display rmon eventlog entry-number 2317 Related command rmon history Syntax display rmon prialarm entry-number Display rmon prialarmRelated command rmon prialarm Current-configuration and display this commands you cannot With the display current-configuration and display Related command rmon statisticsDisplay rmon statistics Undo rmon alarm entry-number Rmon alarm2321 You can create up to 60 alarm entries Table with the rmon event commandRising alarm and falling alarm are alternate Rmon event Rmon history You can create up to 100 alarm entriesUndo rmon history entry number Display rmon history Undo rmon prialarm entry-number Rmon prialarm2325 You can create up to 50 pri-alarm entries Configurations the same and the creation fails# Remove private alarm entry 2327 Rmon statistics Rmon Configuration Commands Display snmp-agent local-switch fabricid Snmp Configuration Commands154 Display snmp-agent community Syntax display snmp-agent group group-name Display snmp-agent groupDescriptions on the fields of display snmp-agent community Name of the specified MIB view Display snmp-agent mib-view2331 Syntax display snmp-agent statistics Display snmp-agent statistics Display snmp-agent sys-info contact location version Display snmp-agent sys-infoVersion Displays the version of the current Snmp agent 2333 Display snmp-agent trap-list Related command snmp-agent trap enableSyntax display snmp-agent trap-list Syntax enable snmp trap updown Undo enable snmp trap updown Enable snmp trap updownDisplay snmp-agent usm-user # Display SNMPv3 information for the user aa Snmp-agent Snmp-agentUndo snmp-agent Undo snmp-agent community community name Snmp-agent community Related command snmp-agentmib-view,snmp-agentusm-user Undo snmp-agent group v3 group-name authentication privacySnmp-agent group Undo snmp-agent group v1 v2c group-name Snmp-agent log Snmp-agent local-switch fabricidSnmp-agent usm-user Undo snmp-agent mib-view view-name Snmp-agent mib-view Snmp-agent packet max-size Related command snmp-agent groupSnmp-agent sys-info 2341 Snmp-agent target-host Related command Display snmp-agentsys-info 2343 Linkup warmstart * system voice vrrp authfailure newmaster Snmp-agent trap enable Snmp-agent trap if-mib link extended Snmp-agent trap if-mib link extendedUndo snmp-agent trap if-mib link extended NMS, the device may not be able to resolute the messages Snmp-agent trap queue-size Snmp-agent trap life Snmp-agent trap source Example # Configure the size of the Trap queue toSnmp-agent usm-user Undo snmp-agent trap source Parameter v1 SNMPv1 2349 Snmp Configuration Commands Copy File System Configuration Commands Syntax dir /all file-url Syntax delete /unreserved file-url Syntax execute filename Execute2353 Fixdisk File promptFile prompt alert quiet Syntax fixdisk device Syntax format device Format# create a subdirectory named mytest under test 2355 Mount MoreSyntax more file-url Syntax mount device Move Related command Example Umount# Mount a CF card on a centralized device 2357 Syntax reset recycle-bin /force Reset recycle-binExample # Move the file cf/test/sample.txt to cf/sample.txt Example # Rename the file sample.txt as sample.bak Syntax umount device Umount2359 Undelete Related command mountExample # Unmount a CF card on a device Syntax undelete file-url Backup startup-configuration Configuration File Management CommandsDisplay saved-configuration Syntax display saved-configuration by-linenum Configuration File Management Commands Related command startup saved-configuration Reset saved-configurationReset saved-configuration backup main Display startup Related command save, display saved-configuration Restore startup-configuration Save Syntax save file-name safely backup main2365 Startup saved-configuration 2367 Related command display startup Configuration File Management Commands Related command ftp timeout and ftp update FTP Server Configuration Commands157 Display ftp-server Syntax ftp server enable Undo ftp server Ftp server enableDescription on the fields of the display ftp-user command Free ftp user Ftp update Ftp timeoutSyntax ftp timeout minute Undo ftp timeout Syntax ftp update fast normal Undo ftp update Sysname system-view Sysname ftp update normal 158 FTP Client Configuration CommandsAscii Binary Syntax cd pathname Debugging CloseSyntax close Syntax debugging Undo debugging View FTP client view Parameter remotefile File name Description on the fields of the debugging command Disconnect # View the content of aa.txtSyntax disconnect 2377 Syntax display ftp client configuration Display ftp client configurationRelated command ftp client source Ftp Ftp client source Ftp client sourceUndo ftp client source Ftp ipv6 Related command display ftp client configuration 2381 Syntax lcd Lcd Open # View the content of file aa.txt2383 Open ipv6 Related command close Syntax passive PassiveUndo passive 2385 Remotehelp Parameter protocol-command FTP command Description on the fields of the remotehelp command # Display the help information for the user command2387 Site NlstSyst Stat Syntax verbose VerboseUndo verbose 2389 FTP Client Configuration Commands Display tftp client configuration Tftp Client Configuration Commands159 Tftp-server acl # Associate IPv6 ACL 2001 with Tftp application in Ipv6 Tftp IP address configured on the device Related command tftp client sourceTftp client source On the source interface, the transmission fails Tftp ipv6 Related command display tftp client configuration 2395 Tftp Client Configuration Commands 160 System Maintaining CommandsPing Ping ipv6 2399 Tracert 65535, in milliseconds. The default value is 5000 ms Range 1 to 65535, defaulting toTracert ipv6 With IPv6 address System Maintaining Commands 161 System Debugging CommandsUndo debugging all module-name option View User view Parameter all All debugging functions Display debugging Related command display debuggingDebugging 162 Basic Configuration CommandsClock datetime Clock summer-time one-off Basic Configuration Commands 2407 Clock summer-time repeating Clock timezone Command-privilege level level view view command Command-privilegeUndo command-privilege view view command Display clock Description Related command Configure-user countDisplay configure-user Display clipboard Syntax display configure-user Display configure-userDisplay clock Syntax display clock Related command configure-user count Display current-configurationExclude text 2413 Special characters in regular expression # Display the configuration beginning with user Display diagnostic-informationDisplay diagnostic-information Version, display device, display current-configuration Syntax display history-command Display history-commandDisplay hotkey Display hotkey Syntax display this by-linenum Display this Syntax display version Display version2417 Undo header incoming legal login motd shell Header incoming legal login motd shell textHeader Ctrl+G corresponds to display current-configuration Hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu commandHotkey Undo hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu # Display the configuration of hotkeys Return Related command quitSuper Syntax return Related command super password Super passwordSuper password level user-level simple cipher password Undo super password level user-level Sysname # Display the password for switching user-levelSyntax sysname sysname Undo sysname 2423 System-view Related command quit, returnSyntax system-view Example # Enter system view from the current user view Description on the fields of the display channel command Information Center Configuration CommandsDisplay channel Example # Display information for channel Syntax display info-center Display info-center 2427 Description on the fields of the display info-center command Represents information level, in the range 0 to Display logbufferSeverity description Meanings of characters in text Rest is omitted here Descriptions on the fields of the display logbuffer command2429 Display logfile buffer Display logbuffer summaryDisplay logbuffer summary level severity Syntax display logfile buffer Example # Display the contents of the log file buffer Support for the command varies with devicesDisplay logfile summary Syntax display logfile summary Info-center channel name Display trapbufferDisplay trapbuffer size buffersize Trap buffer, in the range 1 to 1,024 2433 Info-center console channel Syntax info-center enable Undo info-center enable Info-center enableInfo-center logbuffer Undo info-center logbuffer channel size Example # Enable the log file feature Info-center logfile enableInfo-center logfile frequency 2435 Syntax info-center logfile switch-directory dir-name Info-center logfile switch-directoryInfo-center logfile size-quota # Set the directory to save the log file to cf/test Info-center loghostUndo info-center loghost host-ip 2437 Undo info-center loghost source Info-center loghost source Info-center snmp channel Info-center monitor channelUndo info-center snmp channel 2439 Info-center source Output Modules Enabled Direction Allowed Disabled Severity Default output rules for different output directions2441 NMS Info-center timestamp Info-center synchronous Info-center timestamp loghost date no-year-date none Info-center timestamp loghostUndo info-center timestamp loghost Logfile save Info-center trapbufferUndo info-center trapbuffer channel size Syntax logfile save Reset trapbuffer Reset logbufferTerminal debugging Undo terminal debugging Terminal loggingSyntax terminal logging Undo terminal logging Terminal trapping Terminal monitor Sysname terminal trapping Current terminal trapping is on Acl ipv6 acl-number inbound outbound User Interface Configuration CommandsUndo acl ipv6 acl-number inbound outbound Acl acl-number inbound Syntax activation-key character Undo activation-key Activation-key 2451 Auto-execute command Password Performs local password authentication None Performs no authenticationAAA, refer to AAA Configuration Commands on Users log onto the device using the current user interface Databits 5 6 7 DatabitsUndo databits History-commandmax-size Display history-commandDisplay user-interface 2455 # Display summary about all user interfaces Display users Description on the fields of the display users commandDisplay users all All Displays information about users on all user interfaces Escape-key Syntax escape-key default character Undo escape-keyExample # Define a as the escape key 2457 None Syntax free user-interface num1 aux console tty vty num2 Free user-interface2459 # Terminate the connection with user interface VTY History-command max-sizeView User interface view Lock Password next time you enter the systemLock Operating under the active user interface Only, and cannot be applied to the Console port Example # Set the timeout interval to 50 seconds Example # Set the answering mode to auto-answerParity Syntax parity even mark none odd space Undo parity Protocol inbound Example # Enable the VTYs 0 through 4 to support SSH onlyExample # Perform odd parity check on the AUX interface Syntax protocol inbound all pad ssh telnet Redirect enable Redirect enableUndo redirect enable Redirect disconnect Redirect listen-port Related command telnet, display tcp statistics onRedirect refuse-negotiation Redirect listen-port port-number Redirect return-deal from-telnet Redirect return-deal from-telnetUndo redirect return-deal from-telnet Redirect return-deal from-terminal Redirect timeout Send Screen-lengthSyntax screen-length screen-length Undo screen-length Syntax send all num1 aux console tty vty num2 Set authentication password cipher simple password Set authentication passwordUndo set authentication password Shell Related command authentication-modeSyntax shell Undo shell Speed in user interface view Terminal type Stopbits Syntax user privilege level level Undo user privilege level User privilege level User-interface # Enable user 1 to access level 3 commands# Enter the user interface view of VTY 0 to User Interface Configuration Commands Display mac-address MAC Address Table Management Configuration CommandsEthernet interfaces Display mac-address blackhole vlan vlan-id count Display mac-address mac-learning Display mac-address aging-timeSyntax display mac-address aging-time Port Index 2479 Mac-address Ethernet interface view Mac-address system view Related command display mac-addressBlackhole MAC address entries are dropped Specified Vlan ID, in the range 1 to 2481 Mac-address mac-learning disable Example # Disable global MAC address learning Related command display mac-addressmac-learningMac-address max-mac-count Ethernet interface view Mac-address timer aging seconds no-aging Mac-address timerUndo mac-address timer aging MAC Address Table Management Configuration Commands 166 POE Configuration CommandsApply poe-profile Description on fields of the display poe device command Module, and slot of the power sourcing equipment PSEDisplay poe device Display poe interface 2487 # Display the state of all PoE interfaces Description on fields of the display poe interface command 2489 Display poe interface power # Display the power information of all PoE interfaces Display poe power-usageSyntax display poe power-usage Syntax display poe pse pse-id Display poe pse2491 Syntax display poe-power Display poe-powerDescription on fields of the display poe pse command 2493 Description on fields of the display poe-power command Display poe-profile Existing PoE configuration files will be displayedDisplay poe-profile index index name profile-name Number ranges from 1 to 2495 Description on fields of the display poe-profile command Poe disconnect Display poe-profile interfaceSyntax poe disconnect ac dc Undo poe disconnect Syntax poe enable Undo poe enable Poe enable Poe legacy enable Poe enable pse Poe max-power system view Poe max-powerSyntax poe max-power max-power Undo poe max-power 2499 Related command poe priority system view Poe modePoe mode signal spare Undo poe mode Poe pd-policy priority Poe pd-descriptionSyntax poe pd-description string Undo poe pd-description Syntax poe pd-policy priority Undo poe pd-policy priority Syntax poe priority critical high low Undo poe priority Poe priority Poe priority critical high low pse pse-id Poe priority system viewUndo poe priority pse pse-id Poe update full refresh filename pse pse-id Poe updatePoe pse-policy priority Poe pse-policy priority Poe utilization-threshold Example # Set the power alarm threshold of PSE 2 to 90%Poe-profile Undo poe utilization-threshold pse pse-id Sysname system-view Sysname poe-profile abc Oap connect slot OAP Module Configuration CommandsSyntax oap connect slot slot-number Syntax oap reboot slot slot-number Oap reboot slot Acfp enable Acfp Configuration Commands168 Display acfp client-info Client-idis the Acfp client ID, in the range of 1 to Display acfp policy-infoPolicy-index Policy index, in the range of 1 to Interface-numberis the interface type and interface number 2511 Interface type and interface number Display acfp rule-cacheInterface-number is the interface type and interface number Will display all the Acfp rule cache information Interface number Display acfp rule-infoClient-id Acfp client ID, in the range of 1 to 2513 Establish # Display Acfp rule information in order of policy Syntax display acfp server-info Display acfp server-info2515 Type and interface number Reset acfp rule-cache Acsei server enable Acsei Server Configuration CommandsSyntax acsei server enable Undo acsei server enable Acsei server Acsei timer monitor Acsei timer clock-syncSyntax acsei timer monitor seconds Undo acsei timer monitor Acsei client close Acsei client rebootDisplay acsei client summary # Display the summary of all Acsei clients Display acsei client infoSyntax display acsei client info client-id 2521 # Display information about all Acsei clients CPU information of the Acsei client Acsei-client debug disable Acsei Client Configuration CommandsAcsei-client debug enable 170 Syntax chkconfig acseid off Chkconfig acseid offAcsei-client debug show Syntax acsei-client debug show Service acseid condrestart Chkconfig acseid onSyntax chkconfig acseid on Syntax service acseid condrestart Service acseid restart Service acseid reloadService acseid reload # Load the Acsei client configuration file Service acseid status Service acseid startSyntax service acseid start Syntax service acseid status Service acseid stop Service acseid stopAny directory of the Linux system # Stop an Acsei client that is running Description on the fields of the display track command Track Configuration Commands171 Display track Track Configuration Commands 172 IPX Configuration CommandsDisplay ipx interface Syntax display ipx routing-table network Display ipx routing-table Syntax display ipx routing-table network verbose Display ipx routing-table verbose2533 Display ipx routing-table protocol Inactive Displays inactive service information Display ipx service-tableDisplay ipx routing-table statistics To 47 characters Display ipx statistics # Display detailed IPX service informationSyntax display ipx statistics SAP 2537 Ipx enable node node Ipx enableUndo ipx enable Configuration Syntax ipx netbios-propagation Undo ipx netbios-propagation Ipx netbios-propagationIpx encapsulation Ipx encapsulation dot2 dot3 ethernet-2 snap Ipx rip import-route static Ipx networkUndo ipx network Ipx rip import-route static Ipx rip mtu Example # Enable static route redistribution to RIPIpx rip multiplier Syntax ipx rip mtu bytes Undo ipx rip mtu Related command ipx rip timer update Ipx rip timer updateRelated command ipx rip multiplier Example # Specify a RIP update interval of 30 seconds 2543 Ipx route load-balance-path Syntax ipx sap disable Undo ipx sap disable Ipx sap disableIpx route max-reserve-path Ipx sap gns-disable-reply Ipx sap gns-disable-replyUndo ipx sap gns-disable-reply Ipx sap gns-load-balance Ipx sap max-reserve-servers Related command ipx sap gns-disable-replyIpx sap mtu Syntax ipx sap mtu bytes Ipx sap multiplier Related command ipx sap timer updateUndo ipx sap mtu 2547 Ipx service Ipx sap timer updateRelated command ipx sap multiplier, ipx update-change-only Example # Specify the SAP updating interval as 300 seconds Ipx tick Ipx split-horizonIpx split-horizon Undo ipx split-horizon Syntax ipx update-change-only Undo ipx update-change-only Ipx update-change-onlyPing ipx Reset ipx routing-table statistics protocol Reset ipx statisticsSyntax reset ipx statistics 2551 Example # Display IPX routing statistics Related command display ipx routing-table statistics# Clear IPX static route statistics 173 Voip Configuration Commands Area-id AreaArea custom europe north-america Undo area Busytone-t-th Related command match-template,address, and entitySyntax busytone-t-th time-threshold Undo busytone-t-th 2555 Cid receive Cid displaySyntax cid display Undo cid display Syntax cid receive Undo cid receive Cid type Cid sendSyntax cid send Undo cid send View FXS/FXO voice subscriber line view Undo cid type Cng-onSyntax cng-on Undo cng-on Compression Related command line and vad-onView POTS/VoIP/VoFR entity view 2559 Codec Bandwidth Voice quality Relationship between algorithms and bandwidth 723 r63 algorithm 711 algorithm A-law and µ-law723 r53 algorithm 726 r16 algorithm 726 r32 algorithm 726 r24 algorithm726 r40 algorithm Compression efficiency of IPHC+PPP header Algorithm Syntax cptone country-type locale Undo cptone country-type Cptone country-typeRegions are supported Countries or regions with supported call progress tones IEU 2565 Effect on all voice interfaces of all cards on the device Cptone tone-typeSpecial-dial-tone waiting-tone amplitude value Special-dial-tone waiting-tone amplitude G729r8 Default entity compression Related command compression Default entity payload-size Default entity vad-on Default entity vad-onUndo default entity vad-on Vad-on Delay hold Default subscriber-lineTransmit gain Delay send-dtmf Delay risingRelated command em-signal Syntax delay rising milliseconds Undo delay rising Syntax delay send-wink milliseconds Undo delay send-wink Delay send-wink Delay wink-rising Delay wink-holdSyntax delay wink-hold milliseconds Undo delay wink-hold 2573 Syntax delay start-dial seconds Undo delay start-dial Delay start-dialDescription voice entity view Dial-program Description voice subscriber line viewSyntax dial-program View Voice view Display voice call-info brief mark tag verbose Display voice call-infoRange of 0 to Information table Display voice cmc LGS Syntax display voice default all Display voice default allDescription on fields of the display voice cmc command 2579 Description on fields of the display voice default command Display voice entity Display voice entity command ExampleDisplay voice ipp statistic Display voice entity all mark entity-tag pots voip Voip Configuration Commands Display voice iva statistic Error Displays all the error statistics of IVA moduleCall Displays the calling statistics in the IVA module 2583 Display voice subscriber-line Related command subscriber-lineSyntax display voice subscriber-line line-number = Busytone 2585 CNG Dtmf amplitude Dscp mediaSyntax dscp media dscp-value Undo dscp media Syntax dtmf amplitude value Undo dtmf amplitude Dtmf time Dtmf sensitivity-levelDtmf time interval persist milliseconds Undo dtmf time interval persist Meaning of the index numbers Dtmf threshold2589 Index Meaning Value range Remarks Upper limit of the maximum To 4,999, with 2591 Echo-canceller Related command subscriber-lineand echo-canceller parameter Echo-canceller parameterMix-proportion-ratio value talk-threshold value Mix-proportion-ratio talk-threshold Related command echo-canceller Em-signalEm-phy-parm Entity entity-number pots voip EntityUndo entity entity-numberall pots voip Related command outband, tunnel-on, and voip called-start Related command Line ExampleFast-connect Fast-connect Example # Enable fast connection for VoIP voice entity Hookoff-mode delay bindSyntax hookoff-mode delay immediate Undo hookoff-mode Hookoff-mode Hookoff-time Private-lineand caller-permitcommands when executingIncoming calls Syntax hookoff-time time Undo hookoff-time Impedance Match-template LineUndo line Syntax match-template match-string Undo match-template If you want to use and at the same time, you must use them ThemFormat . Other formats, such as and are illegal Such as 0-9. The formats like 0-A are illegal Nlp-on Command, but analog voice subscriber lines do notE1 voice, T, #, and * are not supported currently Nlp-on Outband Related command Fast-connectand tunnel-on ExamplePayload-size Syntax plc-mode general specific Undo plc-mode Plc-mode2603 Receive gain Related command transmit gain and subscriber-lineSyntax receive gain value Undo receive gain Register-number Reset voice cmc statisticMatch-template Reset voice iva statistic Reset voice ipp statisticRelated command display voice iva statistic Related command display voice ipp statistic Undo send-busytone enable time Send-busytone enable time secondsSend-busytone Been used to identify nonstandard T38 fax packets Shutdown voice entity view Send-ringSyntax send-ring Undo send-ring View Voice entity view Silence-th-span Shutdown voice subscriber line viewExample # Change the status of voice entity 4 to Down Undo silence-th-span Subscriber-line Slic-gainSlic-gain 0 Undo slic-gain Syntax timer dial-interval seconds Undo timer dial-interval Timer dial-interval2611 Timer hookoff-interval Timer first-dialSyntax timer first-dial seconds Undo timer first-dial Timer wait-digit Timer ring-backRelated command hookoff-mode Syntax timer ring-back seconds Undo timer ring-back Transmit gain Related command receive gain and subscriber-lineSyntax transmit gain value Undo transmit gain Tunnel-on Example # Enable the tunnel function for VoIP voice entitySyntax tunnel-on Undo tunnel-on View VoIP entity view Vad-on Related command cng-onUndo type Syntax vad-on Undo vi-card busy-tone-detect custom index Vi-card busy-tone-detect2617 Vi-card cptone-custom Syntax vi-card reboot slot-number Vi-card reboot2619 Voip called-tunnel enable Voice-setupExample # Reset the voice card of slot Syntax voice-setup Voip called-start Voip timerFast-connect Cs7, or ef Vqa dscpDscp values Keyword Dscp value in binary Dscp value in decimal Vqa dsp-monitor buffer-time By default, DSP buffered data is not monitoredView Voice view Parameter Range 180 to Voip Configuration Commands Caller-permit Dial Plan Configuration Commands Dial-prefix Related command match-templateonSyntax dial-prefix string Undo dial-prefix Display voice number-substitute Related command match-templateon page 2599 and send-numberExample # Specify 0 as a prefix Syntax display voice number-substitute list-tag Dot-match Related command number-substituteDot-match end-only left-right right-left Undo dot-match Max-call in voice dial program view First-ruleSyntax first-rule rule-number Undo first-rule Undo max-call set-numberI all Max-call in voice entity view Related command max-call in voice entity viewUndo max-call Related command match-templateon page 2599 and terminator Related command max-call in voice dial program viewExample # Configure the longest-number match policy Number-match Number-priority Related command rule and substitute voice dial program viewNumber-substitute Private-line PriorityUndo priority Syntax private-line string Undo private-line Undo rule rule-tag all Rule 2635 Meanings of characters in the string argument Number type Description Input number typeNumbering plan Description Output numbering plan Input numbering plan2637 Undo select-rule rule-order Select-rule rule-order Meanings of integers Select-rule search-stop2639 Integer Meaning Description Undo select-rule type-first Select-rule type-firstMeanings of values Syntax select-stop Undo select-stop Select-stop2641 Send-number Related command dot-matchand match-templateon Substitute subscriber line view/voice entity view Related command number-substituteand ruleSubstitute called calling list-number Undo substitute called calling All Substitute voice dial program viewNumber-substitute and rule To Pstn are outgoing calls Terminator Related command match-templateon page 2599 and timerSyntax terminator character Undo terminator Example # Specify the pound sign # as the dial terminator Dial Plan Configuration Commands Ani E1 and T1 Configuration CommandsAni all ka Undo ani Related command cas, timer, reverse, and renew Answer enableSyntax answer enable Undo answer enable Ani-offset Callmode Related command re-answer enable and timer dl re-answerCas Callmode segment terminal Example # Enter the R2 CAS view of TS group Clear-forward-ack enable Display voice subscriber line Related command mode2651 CNG/CED Dl-bits Signal Default rx-bits Abcd Default tx-bits Abcd Default values of signals in R2 digital line signaling2653 Related command seizure-ack enable and answer enable Dtmf enableSyntax dtmf enable Undo dtmf enable Related command timer dtmf Syntax final-callednum enable Undo final-callednum enable Final-callednum enableRelated command register-valuedigital-end 2655 Group-b enable Force-metering enableSyntax force-metering enable Undo force-metering enable Syntax group-b enable Undo group-b enable 2657 Related command register-valuereq-switch-groupb Mode Syntax mode zone-name default-standard Undo mode Example # Adopt Hongkong default R2 signaling Related command register-valueand force-metering enablePcm Syntax pcm a-law µ-law Undo pcm Pri-set Example # Adopt µ-law companding for signal quantizationSyntax pri-set timeslot-list range Undo pri-set Syntax re-answer enable Undo re-answer enable Re-answer enableRelated command answer enable and timer dl re-answer 2661 Changeover to Group a signal value, in the range 1 to Req-callednum-and-switchgroupa req-callingcategory reqDemand-refused digit-end nullnum req-billingcategory Subscriber-busy subscriber-charge subscriber-idle 2663 Renew Related command group-b enableSyntax renew Abcd Undo renew Related command cas and reverse Seizure-ack enableRelated command cas and renew Reverse Select-mode Related command timer dl seizureView CAS view Timeslots Related command cas and trunk-direction Sendring ringbusy enableRelated command timer ring 2667 Related command Subscriber line Example Signal-valueSpecial-character Syntax special-character character number Undo special-character character number Different signal values Tdm-clock Related command timeslot-setand pri-setExample # Enter the view of voice subscriber line 1/015 Syntax tdm-clock internal line primary Undo tdm-clock Release-guard Timer dlView R2 CAS view 2671 Syntax timer dtmf time Undo timer dtmf Timer dtmf Related command dtmf enable Timer register-pulse persistenceTimer register-pulse persistence time Undo timer register-pulse persistence Related command timer register-completegroup-b Timer register-complete group-bTimer register-complete group-b time Undo timer register-complete group-b Timer ring ringback ringbusy time Timer ringUndo timer ring ringback ringbusy Timeslot-set Trunk-direction Related command subscriber line and cas Ts block open query reset timeslots timeslots-list Related command cas and select-modeCAS view 2677 Related command cas Default entity fax FAX Over IP Configuration Commands Example # Set the maximum fax rate to 9,600 bps globally Display voice faxSyntax display voice fax statistics 2681 FAXVOFRFRF11SWITCH FaxvofrstandardswitchWaitdpbegdemodulatetimeout Waitdpbegmodulatetimeout Fax baudrate Fax baudrate 2400 4800 9600 14400 disable voiceUndo fax baudrate Syntax fax ecm Fax ecmUndo fax ecm Fax local-train threshold Fax levelSyntax fax level level Undo fax level 2685 Example # Configure NSF for fax signal transmission Example # Configure the fax local training threshold toFax nsf-on Syntax fax nsf-on Undo fax nsf-on Fax protocol pcm g711alaw g711 μlaw Fax protocolUndo fax protocol Fax train-mode VoFR entities only support the PPP training modeFax train-mode local ppp Undo fax train-mode Reset voice fax statistics Reset voice fax statisticsVoip h323-conf tcs-t38 Voip h323-conf tcs-t38 FAX Over IP Configuration Commands 177 Related command match-templateon page 2599, entity onDisplay voice gateway Syntax area-id string Undo area-id string Syntax gk-client Gk-clientGkid Gk-2nd-id Related command gk-idExample # Enter gatekeeper client view Undo gk-2nd-id Related command area-id,gw-id,gk-2nd-id,gw-address,ras-on Gk-security call enableSyntax gk-security call enable Undo gk-security call enable Gk-id Gk-security register-pwd Gk-security register-pwd cipher simple passwordGw-address Undo gk-security register-pwd Undo gw-address Gw-idUndo gw-id Ras-on Related command gw-id,gw-address, and gk-idVoip h323-descriptor Syntax ras-on 323 Configuration Commands 178 SIP Configuration CommandsDisplay voice sip call-statistics Syntax display voice sip call-statistics TPT Message Outband sip Display voice sip register-stateDisplay voice sip register-state Syntax outband sip Undo outband Proxy Default port number isUndo proxy ipv4 SIP client view Register-enable off on Register-enableUndo register-enable Registrar ipv4 Sip Reset voice sipSip-comp Syntax sip Undo sip-comp callee from Sip-comp agentSIP client view SIP request messages Sip-domain Sip-comp serverUndo sip-comp server View SIP client view Syntax source-ip ip-address Undo source-ip Source-ip2707 SIP Configuration Commands Syntax wildcard-register enable Undo wildcard-register Wildcard-register enableExample # Enable fuzzy telephone number registration 2709 SIP Configuration Commands 179 Vofr Configuration CommandsAddress Undo address vofr-dynamic vofr-static Call-mode Related command Trunk-idand address ExampleCid select-mode # Set the CID selection mode to min-poll on Dlci Related command Vofr ExampleDisplay fr vofr-info Interface Dlci view Outband vofr Entity vofrUndo entity entity-number vofr Outband vofr Seq-number Seq-numberUndo seq-number Timestamp Related command call-modeTrunk-id Vofr Voice bandwidthView Interface Dlci view 2717 Related command call-mode Vofr frf11-timer time Vofr frf11-timerUndo vofr frf11-timer Hang up successfully in the FRF.11 trunk mode Vofr Configuration Commands Aaa-client Voice Radius Configuration CommandsAccounting Syntax aaa-client Accounting-did Related command acct-methodand accountingSyntax accounting-did Undo accounting-did View Voice AAA client view # Restore the default accounting method Related command accounting and accounting-didAcct-method Example # Set the accounting method to start-ack Authentication-did AuthenticationSyntax authentication Undo authentication Related command gw-access-numberand authorization Related command authorization-did AuthorizationSyntax authorization Undo authorization 2725 Related command gw-access-numberand authentication Authorization-didSyntax authorization-did Undo authorization-did Related command authentication-did Callednumber receive-method Related command gw-access-number2727 Card-digit Related command gw-access-numberand process-configCdr Syntax card-digit card-digit Undo card-digit # Set the alarm threshold for CDRs to 10% Related command display voice call-history-recordUndo cdr all buffer duration threshold Example # Set the number of CDRs that can be saved to Display voice access-number Display voice access-numberGw-access-number and aaa-client 2731 Display voice call-history-record Example # Display call records by calling number Related command cdr2733 Syntax display voice radius statistic Display voice radius statistic 2735 Related command reset voice radius statisticVORDS=AAA AAA=VORDS CMC=VORDS Gw-access-number # Add the access number 179 and enter access number view Password-digit# Delete the access number # Delete all access numbers Process-config 2739 # Restore the default dialing process for the access number Undo redialtimes Redialtimes Gw-access-numberand process-config Reset voice radius statisticSelectlanguage Display voice radius statistic Voice Radius Configuration Commands

3Com MSR 50, MSR 30 manual 1681

Models: MSR 50 MSR 30

1681

Threshold: 75%

Field