Fast Forwarding Commands | 3Com MSR 30, MSR 50 instruction

826CHAPTER 64: FAST FORWARDING COMMANDS

Parameter inbound: Enables or disables fast forwarding only in the inbound direction.

Description

outbound: Enables or disables fast forwarding only in the outbound direction.

If no parameter is specified, fast forwarding is enabled or disabled in both the inbound and outbound directions.

Use the ip fast-forwardingcommand to enable fast forwarding in the inbound and/or outbound direction(s).

Use the undo ip fast-forwardingcommand to disable fast forwarding in the inbound and/or outbound direction(s).

By default, fast forwarding is enabled in both the inbound and outbound directions.

Fast forwarding applies to high speed link interfaces (such as Ethernet and Frame Relay interfaces) rather than low speed link interfaces.

Fast forwarding is supported on high-speed link interfaces (including Ethernet, synchronous PPP, Frame Relay and HDLC interfaces) with firewall, NAT, or GRE configured. Fast forwarding is also supported on PPP MP links and IPHC compression or VJ compression enabled PPP links.

CAUTION:

■In the case of load balancing using fast forwarding, fast forwarding must be disabled in the corresponding direction of the interface.

■The interface on which fast forwarding is enabled stops sending ICMP Redirect messages.

■After fast forwarding is enabled on an interface, no IP packet debugging information will be displayed for the interface, that is, the debugging ip packet command does not work.

■To implement fast forwarding of data flow, you need to enable fast forwarding in the inbound direction of the receive interface and in the outbound direction of the send interface.

■When a routing interface is different from its physical interface on links such as MP link or PPPoE links, whether fast forwarding is enabled or not on the physical interface does not affect fast forwarding on the routing interface.

Example # Enable fast forwarding in the inbound direction of the Ethernet 1/0 interface.

<Sysname> system-view

[Sysname] interface ethernet 1/0

[Sysname-Ethernet1/0] ip fast-forwarding inbound

# Disable fast forwarding in the inbound direction of the Ethernet 1/1 interface.

<Sysname> system-view

[Sysname] interface ethernet 1/1

[Sysname-Ethernet1/1] undo ip fast-forwarding

Page 826

Image 826

3Com MSR 30, MSR 50 manual Fast Forwarding Commands

Contents

H3C MSR 20/30/50 Series Routers 3Com Corporation Campus Drive Marlborough, MA USA United States Government Legend Contents POS Interface Configuration Commands Adsl Interface Configuration CommandsGeneral Ethernet Interface Configuration Commands Fundamental Serial Interface Configuration Commands Fundamental CE1/PRI Interface Configuration Commands Fundamental CT1/PRI Interface Configuration Commands 14 E1-F Interface Configuration Commands Fundamental CE3 Interface Configuration Commands 15 T1-F Interface Configuration CommandsFundamental CT3 Interface Configuration Commands ATM Configuration Commands Isdn BRI Interface Configuration CommandsDCC Configuration Commands Basic Dlsw Configuration Commands 340 Frame Relay Configuration Commands Hdlc Configuration Commands Garp Configuration CommandsGvrp Configuration Commands Lapb and X.25 Configuration Commands 451 X25 pvc X25 queue-length 453 X25 receive-threshold 454 425 Display x25 hunt-group-info Display x25 map 426455 Modem Configuration Commands Link Aggregation Configuration CommandsLink Aggregation Debugging Commands Port Mirroring Configuration Commands Pppoe Server Configuration Commands PPP Link Efficiency Mechanism Configuration CommandsPppoe Client Configuration Commands Isdn Configuration Commands PPP Debugging CommandsBridging Configuration Commands Debugging ppp Mstp Configuration Commands Voice Vlan Configuration Commands Vlan Configuration CommandsPORT-BASEDVLAN Configuration Commands Port Isolation Configuration Commands Cpos Interface Configuration Commands ARP Configuration Commands Authorized ARP Configuration Commands Gratuitous ARP Configuration CommandsARP Source Suppression Configuration Commands Proxy ARP Configuration Commands Dhcp Snooping Configuration Commands Dhcp Relay Agent Configuration CommandsDhcp Client Configuration Commands Bootp Client Configuration Commands IP Addressing Configuration Commands DNS Configuration CommandsIP Accounting Configuration Commands IP Performance Configuration Commands Urpf Configuration Commands IP Unicast Policy Routing Configuration CommandsUDP Helper Configuration Commands Fast Forwarding Commands Display natpt address-group 863 NAT-PT Configuration Commands840 Display tcp ipv6 status 842 Display natpt aging-time 864 display natpt all Tunneling Configuration Commands Dual Stack Configuration Commands69 IPV6 Unicast Policy Routing Configuration Commands Terminal Access Configuration Commands IP Routing Table Commands BGP Configuration Commands 981 Log-peer-change Ebgp-interface-sensitive977 983 Peer advertise-communityBGP/BGP-VPN instance view BGP Debugging Commands IS-IS Configuration Commands IS-IS Debugging Commands Ospf Configuration Commands 1128 1155 Snmp-agent trap enable ospf1117 1140 Routing Policy Common Configuration Commands RIP Configuration Commands1179 Static Routing Configuration Commands 79 IPV4 Routing Policy Configuration Commands80 IPV6 Routing Policy Configuration Commands 82 IPV6 BGP Configuration Commands 1243 12231246 83 IPV6 IS-IS Configuration Commands 84 IPV6 OSPFV3 Configuration Commands Multicast Routing and Forwarding Configuration Commands 85 IPV6 Ripng Configuration Commands86 IPV6 Static Routing Configuration Commands Delete ipv6 static-routes all 1325 ipv6 route-static Cache-sa-enable 1365 display msdp brief Igmp Configuration CommandsMsdp Configuration Commands 1366 PIM Configuration Commands 1376 1422 14211429 93 IPV6 PIM Configuration Commands MLD Configuration Commands1451 Display multicast-domain vpn-instance share-group Multicast VPN Configuration Commands1495 1505 Mpls Basics Configuration Commands Mpls TE Configuration Commands Mpls rsvp-te reliability 1610 Mpls rsvp-te resvconfirm 1611 Mpls L2VPN Configuration Commands Mpls L3VPN Configuration Commands VAM Server Configuration Commands 1697 Dvpn Tunnel Configuration Commands VAM Client Configuration CommandsIpsec Profile Configuration Commands GRE Configuration Commands Line Rate Configuration Commands Traffic Policing TP Configuration CommandsTraffic Shaping Configuration Commands Defining Class Commands CQ Configuration Commands Fifo Queuing Configuration CommandsPQ Configuration Commands WFQ Configuration Commands Port Priority Configuration Commands QOS Token Configuration CommandsPriority Mapping Table Configuration Commands Port Priority Trust Mode Configuration Commands AAA Configuration Commands access-limit FR QOS Configuration Commands126 802.1X Configuration Commands Reset dar session 1927 Radius Configuration Commands1958 Hwtacacs Configuration Commands Packet Filter Firewall Configuration Commands MAC Authentication Configuration Commands Aspf Configuration Commands aging-timeNAT Configuration Commands PKI Configuration Commands Common Configuration Commands Portal Configuration CommandsRSH Configuration Commands rsh 138 IPV4 ACL Configuration Commands Ipsec Configuration Commands IKE Configuration Commands 142 SSH2.0 Configuration Commands Sftp Configuration Commands bye SSL Configuration Commands Vrrp Configuration Commands for IPV6 Backup Center Configuration Commands146 IPV4-BASEDVRRP Configuration Commands Device Management Commands 2262 NQA Client Configuration CommandsTemperature-alarm enable 2263 Temperature-limit 2276 NTP Configuration Commands NQA Server Configuration CommandsNetstream Configuration Commands Rmon Configuration Commands Snmp Configuration Commands File System Configuration Commands cd FTP Client Configuration Commands ascii Configuration File Management CommandsFTP Server Configuration Commands Tftp Client Configuration Commands Basic Configuration Commands System Maintaining CommandsSystem Debugging Commands Information Center Configuration Commands User Interface Configuration Commands 2460 POE Configuration Commands MAC Address Table Management Configuration CommandsOAP Module Configuration Commands Acsei Client Configuration Commands Acfp Configuration CommandsAcsei Server Configuration Commands Track Configuration Commands 2546 Voip Configuration Commands address2551 Reset ipx routing-table statistics protocol Area 2554 area-id 2592 Caller-permit Dial Plan Configuration Commands175 E1 and T1 Configuration Commands ani 2639 177 H.323 Configuration Commands FAX Over IP Configuration CommandsSIP Configuration Commands 2716 Vofr Configuration CommandsVoice Radius Configuration Commands aaa-client 2734 Lists text conventions that are used throughout this guide About this GuideLists icon conventions that are used throughout this guide Text Conventions Related Documentation Alphabetical Listing of Commands Area Ospf view 1108 area OSPFv3 viewPage Page Rp IPv6 PIM view 1464 c-rp PIM view Page Display bgp vpnv4 vpn-instancerouting-table Page Display ipv6 policy-based-route statistics Page Page Page Page Page Fr compression frf9 385 fr compression iphc Page Igmp last-member-query-interval Ipv6 nd autoconfig managed-address-flag Page Page Page Mpls te resv-style 1631 mpls te retry 2308 Peer keep-all-routesBGP/BGP-VPN instance view Peer ebgp-max-hopBGP/BGP-VPN instance viewPeer allow-as-loopBGP/BGP-VPN instance view Peer next-hop-invariableBGP-VPNv4 subaddress family view Peer next-hop-localBGP/BGP-VPN instance viewPeer preferred-valueBGP/BGP-VPN instance view Peer public-as-onlyBGP/BGP-VPN instance view Pppoe-servermax-sessionsremote-mac Primary accounting Hwtacacs scheme view Qos wred ip-precedence 1850 qos wred queue table Reset aspf session 2007 reset atm interface 112 reset bgp Reset pim ipv6 control-message counters Page Page Ssl client-policy 2215 ssl server-policy Statistics interval 1562 step for IPv4 2100 step for IPv6Page Page Page X29 timer inviteclear-time Page Display interface atm Public ATM and DSL Interface CommandsSyntax display interface atm interface-number Syntax reset atm interface atm interface-number Reset atm interfaceInterface atm Cable Configuration CommandsClock Code ami b8zs CodeCode ami hdb3 Undo code Syntax display interface ima-group group-interfacenumber Differential-delayDisplay interface ima-group 115 ATM direct mapping CRC4 ADM Frame-formatView ATM E1/T1 interface view Parameter ESF ADM Syntax frame-length 32 64 128 Undo frame-length Frame-lengthIma ima-group Syntax ima ima-group group-number Undo ima ima-group Example # Add the link of ATM E1 interface 5/0 to IMA group Ima-clockSyntax ima-clock ctc link-number number itc Undo ima-clock Ima-test link-number number pattern-id id Ima-standardIma-test Undo ima-test Loopback By default, IMA group interface test is disabledInterface ima-group Syntax loopback cell local payload remote Undo loopback Syntax min-active-links number Undo min-active-links Min-active-linksScramble Syntax scramble Undo scramble Parameter None Syntax cable long short Undo cable Slave Sets the clock mode as slaveView ATM E3/T3 interface view Frame-format g751-adm g751-plcp g832-adm Frame-format cbit-adm cbit-plcp m23-adm m23-plcp Loopback cell local payload remote ATM E3/T3 Interface Configuration Commands Frame-format sdh sonet Loopback cell local remote View ATM OC-3c interface view, STM-1 interface view 129 ATM OC-3C/STM-1 Interface Configuration Commands Syntax activate Undo activate Shdsl Interface Configuration CommandsActivate View ATM G.SHDSL interface view Display dsl configuration Field Description Syntax display dsl status interface atm interface-number Display dsl status133 Gspn Description on the fields of the display dsl status command 135 Syntax display dsl version interface atm interface-number Display dsl versionITU G991.2 Annex A, ITU Shdsl mode Shdsl annex Shdsl rate Example # Set the operating mode of interface ATM 5/0 to COShdsl psd Syntax shdsl psd asymmetry symmetry Undo shdsl psd # Configure ATM 5/0 to operate in the auto-negotiation mode Single-pair interface rate to auto modeKbps four-wire G.SHDSL interface rate is 4,624 kbps Use the undo shdsl snr-margincommand to restore the default Shdsl wire 2 4-auto-enhanced 4-enhanced 4-standard Shdsl wireUndo shdsl wire 141 Shdsl Interface Configuration Commands View ATM Adsl interface view Adsl Interface Configuration CommandsExample # Activate Adsl interface 2/0 Adsl standard auto g9923 g9925 gdmt glite t1413 Adsl standardAdsl tx-attenuation Undo adsl standard Bootrom update file 145 Display dsl configuration 147 LS0US FieldDescription Dslam 149 Bdcm Adsl Interface Configuration Commands Crc POS Interface Configuration CommandsSyntax crc 16 Undo crc Display interface pos Syntax display interface pos interface-number 153 LCP opened, Ipcp opened, IP6CP opened Display ip interface pos interface-number Display ip interface posDisplay ipv6 interface pos Syntax display ipv6 interface pos interface-number Flag Example # Set the SDH overhead byte J0 of POS1/0 interface Related command display interface pos# Set the framing format on interface POS 1/0 to SDH Local Internal loopback Link-protocolLoopback local remote Remote External loopback Interfaces cannot be connected successfully MtuThat the state of the link layer protocol is reported up Syntax mtu size Syntax threshold sd sf value Undo threshold sd sf Example # Enable payload scrambling on interface POS 1/0Threshold 159 Example # Set the SD threshold to 10e-4 for POS 1/0 Related command display port combo and shutdown General Ethernet Interface Configuration CommandsCombo enable Description Special characters used in regular expressions Display brief interfaceCharacter Meaning Example # Display brief information of interfaces Related command interface163 Pvid Display interfaceAcronyms for different types of Interface Interface name Acronyms 165 Field Output queue Fifo queuing 167 Flow-control Related command speedDuplex Syntax duplex auto full half Undo duplex E1/0 InterfaceCan be represented as 1/0 Syntax loopback external internal Undo loopback Port link-mode bridge route Support for these two commands varies with device modelsPort link-mode Undo port link-mode View User view Reset counters interfaceExample # Configure Ethernet1/0 to work in bridge mode 171 Shutdown Speed Related command duplex 173 General Ethernet Interface Configuration Commands Broadcast-suppression Syntax display loopback-detection Display loopback-detectionDisplay port Display port hybrid trunk Display port-group manual all name port-group-name Display port-group manualExamples Syntax flow-interval interval Undo flow-interval Flow-intervalGroup-member Undo group-member interface-list Loopback-detection control enable 179 Loopback-detection interval-time Loopback-detection enableRelated command loopback-detection control enable View System view/Ethernet interface view Related command display loopback-detection Loopback-detection per-vlan enable181 Multicast-suppression Optical port of a Combo port does not support this commandMdi Mdi across auto normal Port-group manual port-group-name aggregation agg-id Port-groupUndo port-group manual port-group-name Virtual-cable-test Currently, these two commands are not supportedUnicast-suppression Syntax virtual-cable-test 185 Page Example # Configure MTU for Ethernet1/0 to be 1,000 bytes Timer holdSyntax timer hold seconds Undo timer hold Configuration Commands for Ethernet Interfaces in Route Mode Syntax async mode flow protocol Undo async mode Fundamental Serial Interface Configuration CommandsAsync mode Baudrate Clock dteclk1 dteclk2 dteclk3 dteclk4 dteclkauto Clock serial interface viewUndo baudrate View Serial interface view 191 Dteclk1Clock selection option Description Syntax code nrzi Undo code Code nrziCountry-code View Synchronous serial interface view Syntax crc 16 32 none Undo crc Example # Configure to adopt 32-bit CRCDetect Asynchronous serial interface detect dsr-dtr Syntax eliminate-pulse Undo eliminate-pulse Eliminate-pulseView Asynchronous serial interface view Syntax idle-mark Undo idle-mark Idle-markInvert receive-clock Syntax invert receive-clock Undo invert receive-clock Invert transmit-clock Syntax invert transmit-clock Undo invert transmit-clock Syntax loopback Undo loopback Mtu on serial interfaces197 Syntax physical-mode async sync Physical-modePhy-mru Syntax phy-mru size Undo phy-mru Syntax reverse-rts Undo reverse-rts Reverse-rts199 Undo virtualbaudrate VirtualbaudrateVirtualbaudrate virtualbaudrate Baudrate Fundamental CE1/PRI Interface Configuration Commands Channel-set CE1/PRI interface view Clock CE1/PRI interface view Clock Controller e1 Code CEI/PRI interface viewController e1 number Crc 16 32 none Detect-aisSyntax detect-ais Undo detect-ais Syntax display controller e1 interface-number Description on the fields of the commandDisplay controller e1 205 Error-diffusion restraint config Undo error-diffusion restraint config By default, error packets diffusion restraint is enabled Error-diffusion restraint enableError-diffusion restraint restart-channel Example # Enable error packets diffusion restraint Idlecode CE1/PRI interface view Frame-format CE1/PRI interface viewTwo types of line idle code are available 0x7E and 0xFF Itf number number type 7e ff Itf CE1/PRI interface viewUndo itf type number Loopback local payload remote Loopback CE1/PRI interface viewPri-set CE1/PRI interface view Pri-set timeslot-list list Command Reset counters controller e1Reset counters controller e1 interface-number Display controller e1 interface-number command Using ce1 e1 Using CE1/PRI interface viewUndo using Level-2 Fundamental CT1/PRI Interface Configuration CommandsAlarm-threshold Level-2 , level-3 , and level-4 Undo bert Bert CT1/PRI interface viewBert pattern 215 220 time minutes unframed Ranges from 1 to 1,440 Channel-set CT1/PRI interface view Cable CT1/PRI interface view655ft Clock CT1/PRI interface view View CT1/PRI interface view Ami Adopts AMI line code format Code CT1/PRI interface viewController t1 # Set the line code format of the interface T1 2/0 to AMI Data-coding inverted normal Data-coding CT1/PRI interface viewUndo data-coding Syntax display controller t1 interface-number Display controller t1219 Clock or slave for the line clock 221 Error-diffusion restraint config Example # Enable error packet diffusion restraint By default, the function is disabled223 Fdl Support of this command varies with device modelError packet diffusion restraint function Set-number argument is a channel set number Idlecode CT1/PRI interface view Frame-format CT1/PRI interface viewFrame-format esf sf Syntax itf number number type 7e ff Undo itf number type Itf CT1/PRI interface viewLoopback CT1/PRI interface view Syntax loopback local payload remote Pri-set CT1/PRI interface view Remote Enables the interface to perform remote loopback# Enabled remote loopback on interface T1 2/0 Loopback on the CT1/PRI interface For a CT1/PRI interface Reset counters controller t1Reset counters controller t1 interface-number # Clear the controller counter for CT1/PRI interface T1 2/0 Sendloopcode 229 Fundamental CT1/PRI Interface Configuration Commands Display fe1 E1-F Interface Configuration CommandsDisplay fe1 serial interface-number Fe1 cable long short Fe1 cableFe1 clock Undo fe1 cable Fe1 code Fe1 detect-ais Fe1 frame-format Fe1 loopback Undo fe1 loopback Local Sets the interface in internal loopback modeFe1 timeslot-list Syntax fe1 timeslot-list list Undo fe1 timeslot-list Fe1 itf Related command fe1 unframedFe1 idlecode Syntax fe1 idlecode 7e ff Undo fe1 idlecode Fe1 unframed Fe1 unframedUndo fe1 unframed Related command fe1 timeslot-list Display ft1 T1-F Interface Configuration CommandsDisplay ft1 serial interface-number Description on the fields of the display ft1 serial command 241 Bert statestopped, not completed Undo ft1 bert Ft1 bert T1-F interface viewFt1 bert pattern 215 220 time minutes unframed T1-F interface view View T1-F interface view Ft1 cableSyntax ft1 cable long decibel short length Undo ft1 cable 243 Ft1 clock master slave Ft1 clockFt1 code Undo ft1 clock Ft1 data-coding inverted normal Ft1 data-codingUndo ft1 data-coding Ft1 fdl Ft1 frame-format Ft1 idlecode 7e ff Ft1 idlecodeFt1 itf Undo ft1 idlecode Ft1 loopback local payload remote Use the undo ft1 loopback command to restore the defaultFt1 loopback Undo ft1 loopback Ft1 timeslot-list # Set T1-F interface Serial 2/0 in local loopback mode249 Undo ft1 alarm-threshold Ft1 alarm-thresholdOn the T1-F interface Ft1 sendloopcode 251 T1-F Interface Configuration Commands Bert CE3 Interface Fundamental CE3 Interface Configuration CommandsBert pattern 27 211 215 qrss time number unframed Display controller e3 Clock CE3 interface viewController e3 Example # Enter the view of interface E3 2/0 Syntax display controller e3 interface-number Display controller e3255 Fundamental CE3 Interface Configuration Commands E1 bert 257 E1 set clock Related command e1 unframedE1 channel-set Syntax e1 line-numberset clock master slave View CE3 interface view E1 set frame-formatUndo e1 line-numberset clock 259 E1 shutdown E1 set loopbackUndo e1 line-numbershutdown Fe3 Related command e1 channel-setE1 unframed Undo e1 line-numberunframed Use the undo fe3 command to restore the default CE3 interface in FE3 mode viewSet the DSU mode or the subrate These two commands are only available in E3 mode National-bit 0 Loopback CE3 interface viewNational-bit Undo national-bit Syntax using ce3 e3 Undo using Using CE3 interface viewRelated command controller e3 Example # Set the national bit to 0 on interface E3 2/0 Alarm detect generate ais febe idle rai Fundamental CT3 Interface Configuration CommandsAlarm CT3 interface view Undo alarm detect generate ais febe idle rai # Enable CT3 interface T3 2/0 to send AIS alarm signals Bert CT3 interface view Syntax cable feet Cable CT3 interface viewClock CT3 interface view 267 Example # Enter the view of interface T3 2/0 Related command display controller t3Controller t3 None Adopts no CRC Syntax display controller t3 interface-number Display controller t3269 AIS Configurable and default to line 271 LOS, LOF, AIS, or RAI Feac CT3 interface view Ft3 Frame-format CT3 interface viewFrame-format c-bit m23 275 Loopback CT3 interface view Mdl CT3 interface view 277 # Set LIC to hello for CT3 interface T3 2/0 T1 alarm# Send path messages on CT3 interface T3 2/0 T1 bert 279 Related command t1 unframed T1 channel-set T1 sendloopcode 281 T1 set clock T1 set frame-format View CT3 interface view T1 set loopbackT1 set fdl 283 T1 show T1 shutdown Description on the fields of the t1 show command285 Undo t1 line-numbershutdown Related command t1 channel-setT1 unframed Syntax t1 line-numberunframed undo t1 line-numberunframed Ct3 Sets the CT3 interface to operate in channelized mode Using CT3 interface viewUsing ct3 t3 T3 Sets the CT3 interface to operate in unchannelized mode Fundamental CT3 Interface Configuration Commands Loopback b1 b2 both Isdn BRI Interface Configuration CommandsLoopback Isdn BRI interface view Fixed Isdn interfaces on your router, if there is any Isdn BRI Interface Configuration Commands Atm class ATM Configuration CommandsRelated command atm-class Atm-class Syntax atm-link check Undo atm-link check Related command atm classAtm-link check View ATM P2P sub-interface view Display atm class Related command Display atm interface ExampleDisplay atm class atm-class-name Display atm interface Syntax display atm interface atm interface-number Display atm map-info 295 PVC-NAME Display atm pvc-groupVPI/VCI State Display atm pvc-info 297 Syntax encapsulation aal5-encap Undo encapsulation EncapsulationIndex Example # Enter Atm1/0 interface Ip-precedence299 Map bridge Related command pvc-group,pvcView PVC view/ATM Class view # Create PVC 1/102 on the ATM interface Atm2/0 # Configure an IP address 10.1.1.1/16 for the VE interfaceMap ip Map ip inarp minutes broadcast Undo map ip inarp Map ppp Syntax map ppp virtual-template vt-number Undo map ppp # Create PVC 1/101 on interface Atm1/0 # Create a PPPoA map using the VT interface created303 Oam ais-rdi Undo oam frequency Oam frequency305 Oamping interface Pvc 307 Related command display atm pvc-info,pvc max-numberVCI range for each type of ATM interface Interface type Pvc max-number Related command ip-precedence,pvcPvc-group Syntax pvc max-number max-number Undo pvc max-number Pvp limit Undo pvp limit vpi Example # Set the traffic of VP with vpi 1 to 2M Service cbrInterface type Value range of output-pcr Related command service vbr-nrt,service vbr-rt,service ubr Service ubrService vbr-nrt Syntax service ubr output-pcr Service vbr-rt Related command service ubr, service vbr-rt, and service cbr # Bring up ATM 5/0 Parameters None313 Transmit-priority Syntax transmit-priority value Undo transmit-priority Dialer bundle DCC Configuration CommandsRelated command dialer bundle-member Dialer bundle-member Related command dialer bundle Dialer callback-center Dialer call-in 317 Related command interface dialer Related command dialer callback-centerDialer circular-group Undo dialer enable-circular Dialer enable-circularDialer enable-circular Bundle-member command Dialer flow-interval Related command dialer circular-groupRelated command dialer threshold Dialer isdn-leased physical interface view Syntax dialer number dial-number Undo dialer number Dialer number321 Dialer queue-length Related command dialer routeDialer priority Syntax dialer priority priority Undo dialer priority Dialer route 323 Dialer threshold Related command dialer flow-interval Dialer timer autodial325 Dialer timer compete Syntax dialer timer enable seconds Undo dialer timer enable Dialer timer enableDialer timer idle Syntax dialer timer idle seconds Undo dialer timer idle Dialer user Dialer timer wait-carrierSyntax dialer user username Undo dialer user Syntax dialer-group group-number Undo dialer-group Dialer-groupExample # Add a remote username routerb 329 Dialer-rule Related command dialer-ruleExample # Add interface Serial 2/0 to dialer access group Undo dialer-rule group-number Any view Related command dialer-groupDisplay dialer Number Number Dialer interface number Display interface dialerDisplay interface dialer number Information about all the dialer interfaces Syntax interface dialer number Undo interface dialer number Interface dialer333 Ppp callback client server Ppp callbackPpp callback ntstring Undo ppp callback client server Undo ppp callback ntstring Related command ppp callback335 DCC Configuration Commands Display dlsw circuits Basic Dlsw Configuration CommandsExample # Configure Serial 1/0 to use Nrzi encoding Syntax display dlsw circuits circuit-id verbose Display dlsw information Display dlsw information local ip-address Syntax display dlsw remote ip-address Display dlsw remote# Display the local information about capabilities exchange 339 Information of DLSw Display dlsw reachable-cacheDisplay dlsw reachable-cache # Display the reachability information of DLSw Syntax display llc2 circuit circuit-id Description on the fields of the display llc2 commandDisplay llc2 341 Syntax dlsw enable Undo dlsw enable Dlsw enableDlsw bridge-set Dlsw ethernet-frame-filter # Enable DLSw343 Dlsw local Dlsw reachable # Allow the router to access SAP addresses 12345 Dlsw remote # Permit access to user-configured MAC addresses onlyDlsw reachable-cache Undo dlsw remote ip-address 347 Dlsw max-transmission Related command sdlc mac-map remoteDlsw reverse Syntax dlsw reverse mac-address Undo dlsw multicast Dlsw multicast349 Dlsw timer Syntax link-protocol sdlc Link-protocol sdlc351 Syntax llc2 max-ack length Undo llc2 max-ack Llc2 max-ackLlc2 max-pdu Syntax llc2 max-pdu length Undo llc2 max-pdu Syntax llc2 max-send-queue length Undo llc2 max-send-queue Llc2 max-send-queueLlc2 max-transmission 353 Llc2 modulo 8 Llc2 moduloLlc2 receive-window Undo llc2 modulo Syntax llc2 timer ack mseconds Undo llc2 timer ack Llc2 timer ackLlc2 timer ack-delay 355 Syntax llc2 timer busy mseconds Undo llc2 timer busy Llc2 timer busyLlc2 timer detect Syntax llc2 timer detect mseconds Undo llc2 timer detect Syntax llc2 timer poll mseconds Undo llc2 timer poll Llc2 timer poll357 Reset dlsw circuits Llc2 timer rejectReset dlsw reachable-cache Description on the fields of the reset dlsw tcp command Reset dlsw tcpSyntax reset dlsw tcp ip-address 359 Sdlc controller Sdlc mac-map local Sdlc enable dlswSyntax sdlc enable dlsw Undo sdlc enable dlsw 361 Sdlc mac-map remote Syntax sdlc max-pdu number Undo sdlc max-pdu Sdlc max-pduSdlc max-send-queue Syntax sdlc max-send-queue length Undo sdlc max-send-queue View Synchronous serial interface view Sdlc max-transmissionSdlc modulo Specifies the modulus value to be Sdlc sap-map local Related command sdlc sap-map remote365 Sdlc simultaneous Related command sdlc sap-map localSdlc sap-map remote Syntax sdlc simultaneous Undo sdlc simultaneous Sdlc status primary secondary Sdlc statusUndo sdlc status primary secondary Sdlc timer lifetime Sdlc timer ackSyntax sdlc timer ack mseconds Undo sdlc timer ack Sdlc window Sdlc timer pollSyntax sdlc timer poll mseconds Undo sdlc timer poll Syntax sdlc window length Undo sdlc window Sdlc xid Undo sdlc xid sdlc-address Display fr compress Frame Relay Configuration CommandsAnnexg Annexg dce dte Display fr dlci-switch Related commands fr compression frf9 Display fr interface Related command fr inarp ExampleDisplay fr inarp-info # Display statistics about frame relay Inarp packets # Display information about all frame relay interfaces Display fr lmi-infoRange 0 to Frame Display fr iphc Related command fr compression iphc375 Whether dynamic address mapping operates normally Display fr map-infoMappings or the one for the specified interface Fr map ip , fr inarp 377 Display fr map-info pppofrDlci = 100, IP Inarp Statistics about data transmitted and received on them Display fr pvc-info1007 Fr dlci Display fr statistics 379 Display interface mfr MTU Display mfr 381 Description on the fields of the display mfr command LID Syntax display x25 template name Display x25 template383 Related command x25 template, x25-template Syntax fr compression frf9 Undo fr compression Fr compression frf9Fr compression iphc View Subinterface point-to-point view Undo fr compression iphc Fr dlciUndo fr dlci dlci-number Undo fr dlci-switch in-dlci Fr dlci-switchUse the undo fr dlci command to cancel the configuration Related command fr switching Fr inarp Syntax fr inarp ip dlci-number Undo fr inarp ip dlci-number Syntax fr interface-type dce dte nni Undo fr interface-type Fr interface-type389 Tcp-include Fr iphcFr lmi n391dte Fr map ip , fr compression iphc Syntax fr lmi n392dce n392-value Undo fr lmi n392dce Fr lmi n392dce391 Fr lmi n392dte Syntax fr lmi n392dte n392-value Undo fr lmi n392dte Syntax fr lmi n393dce n393-value Undo fr lmi n393dce Fr lmi n393dceFr lmi n393dte Syntax fr lmi n393dte n393-value Undo fr lmi n393dte Fr lmi t392dce Syntax fr lmi t392dce t392-value Undo fr lmi t392dce Fr lmi type ansi nonstandard q933a bi-direction Fr lmi typeUndo fr lmi type Fr map ip Undo fr switch name Fr switchRelated command interface virtual-templateon Fr map ppp Fr switching Syntax fr switching Undo fr switching Interface serial Interface mfr399 Link-protocol fr Link-protocol fr ietf nonstandard Syntax link-protocol fr mfr interface-number Link-protocol fr mfrMfr bundle-name Syntax mfr bundle-name name Undo mfr bundle-name Syntax mfr fragment Undo mfr fragment Mfr fragmentMfr fragment-size Syntax mfr fragment-size bytes Undo mfr fragment-size Syntax mfr link-name name Undo mfr link-name name Mfr link-name403 Mfr stateup-respond-addlink Mfr retrySyntax mfr retry number Undo mfr retry Related command mfr timer hello, mfr retry Mfr timer ackSyntax mfr timer ack seconds Undo mfr timer ack 405 Mfr window-size Mfr timer helloSyntax mfr timer hello seconds Undo mfr timer hello Syntax mfr window-size number Undo mfr window-size Syntax reset fr inarp Reset fr inarpView Frame relay switching view Related command fr inarp Related command fr lmi t392dce Reset fr pvcExample # Clear all the frame relay dynamic address maps Syntax x25-template name Undo x25-template name X25-templateX25 template Syntax x25 template name Undo x25 template name Frame Relay Configuration Commands Syntax display garp timer interface interface-list Garp Configuration CommandsDisplay garp timer Display garp statistics Example # Display Garp timers on port Ethernet 1/0 Garp timerRelated command garp timer, garp timer leaveall View Ethernet interface view, port group view Dependencies of Garp timers Garp timer leaveallRelated command display garp timer Timer Lower limit Upper limit Reset garp statistics interface interface-list Reset garp statisticsDisplay gvrp statistics Display gvrp statistics Gvrp Configuration CommandsSyntax display gvrp statistics interface interface-list Gvrp Related command display gvrp statusDisplay gvrp status Syntax gvrp Undo gvrp registration Gvrp registrationGvrp registration fixed forbidden normal Display garp statistics Gvrp Configuration Commands Timer hold seconds Hdlc Configuration CommandsTimer hold Link-protocol hdlc Hdlc Configuration Commands Channel Lapb and X.25 Configuration CommandsX25 hunt-group Lapb and X.25 Configuration Commands 423 Description on the fields of the display interface commandLapb DCE Display x25 alias-policy Display x25 hunt-group-info Related command x25 alias-policy ExampleDisplay x25 cug Display x25 cug local-cug local-cug-number network-cug Display x25 map Related command x25 hunt-groupSyntax display x25 map Example # Display the X.25 address mapping table Description on the fields of the display x25 map commandDisplay x25 pad Syntax display x25 pad pad-id Syntax display x25 switch-table pvc Display x25 switch-table pvcDisplay x25 switch-table svc Syntax display x25 switch-table svc dynamic static Display x25 vc Related command x25 switch svcExample # Display X.25 SVC static switching table Syntax display x25 vc lci Data 0/0 Interrupt 0/0 431 Description on the fields of the display x25 vc commandSVC Display x25 x2t switch-table Display x25 xot 433 Lapb max-frameSyntax lapb max-frame n1-value Undo lapb max-frame Difference between N1 Lapb retry Related command lapb window-sizeLapb modulo Parameter 8 Modulo Lapb window-size Lapb timerUndo lapb timer t1 t2 t3 Syntax lapb window-size k-valueundo lapb window-size Lapb modulo Link-protocol lapbLink-protocol lapb dce dte ip multi-protocol Pad Link-protocol x25 dce dte ietf nonstandard Reset xot Reset Translate ip Reset lapb statisticsSyntax reset lapb statistics Undo translate ip ip-addressport port-number Undo translate x25 x.121-address TranslateParameter x.121-address X.121 address X25 alias-policy 441 X25 call-facility Description on the user facility option 443 X25 cug-serviceRelated command x25 map, x25 modulo Option Description Window-size X25 default-protocol Related command x25 local-cug X25 hunt-group 445 X25 ignore called-address X25 ignore calling-address X25 local-cug 447 X25 map Related command x25 call-facility,x25 cug-serviceUndo x25 map ip compressedtcp protocol-address Option Description Broadcast Send-delay delay-time449 Protocols such as Routing Information Protocol X25 modulo Syntax x25 modulo 8 Undo x25 modulo Undo x25 packet-size X25 packet-size# Set the modulo on the X.25 interface Serial 2/0 to 451 Undo x25 pvc pvc-number X25 pvcDescription on PVC attribute option Syntax x25 queue-length queue-length Undo x25 queue-length X25 queue-length453 Related command x25 window-size X25 receive-threshold X25 response calling-address X25 response called-address455 Related command x25 map X25 reverse-charge-accept Undo x25 switch pvc pvc-number1 X25 switch pvcRelated command x25 call-facility,x25 map X25 roa-list Lapb and X.25 Configuration Commands 121 mode matching rules X25 switch svc459 Number SVC route number Input rules of X.121 address mode matching stringCharacters Input rules X25 switch svc hunt-group 461 X25 switch svc xot Related command display x25 switch-table svc X25 switching Syntax x25 switching Undo x25 switching Example # Enable X.25 switching function X25 timer holdX25 timer idle Syntax x25 timer hold minutes Undo x25 timer hold Related command x25 timer tx1, x25 timer tx2, x25 timer tx3 X25 timer tx0Syntax x25 timer tx0 seconds Undo x25 timer tx0 465 Syntax x25 timer tx1 seconds Undo x25 timer tx1 X25 timer tx1X25 timer tx2 Related command x25 timer tx0, x25 timer tx2, x25 timer tx3 Syntax x25 timer tx3 seconds Undo x25 timer tx3 X25 timer tx3Related command x25 timer tx0, x25 timer tx1, x25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx2 X25 vc-range X25 vc-per-mapSyntax x25 vc-per-map count Undo x25 vc-per-map Undo x25 window-size X25 window-size469 X25 xot pvc X25 x121-addressSyntax x25 x121-address x.121-address Undo x25 x121-address XOT channel parameter option Related command display x25 vc, x25 switchingUndo x25 pvc pvc-number1 471 X29 timer inviteclear-time Display link-aggregation interface Link Aggregation Configuration CommandsDisplay lacp system-id Syntax display lacp system-id Link Aggregation Configuration Commands Syntax display link-aggregation summary Display link-aggregation summary475 Syntax display link-aggregation verbose agg-id Display link-aggregation verboseExample # Display the link aggregation group summary AL ID 477 Lacp port-priority Example # Assign Lacp priority 64 to a port Lacp system-priorityLink-aggregation group description 479 Related command display link-aggregation summary Link-aggregation group modeRelated command display link-aggregation verbose Port link-aggregation group Port-group aggregation Reset lacp statisticsRelated command Display link-aggregation verbose Example Port-group aggregation agg-id Related command display link-aggregation interface Example # Clear statistics about Lacp on all ports View User view Default Level 1 Monitor level Link Aggregation Debugging CommandsDebugging lacp packet Link Aggregation Debugging Commands Length of the Terminator field in the protocol packet is Device sent an Lacp protocol packet through Ethernet 1/1485 Device received an Lacp protocol packet through Ethernet 1/1 Debugging lacp state 487 Debugging link-aggregation error Syntax debugging link-aggregation error Syntax debugging link-aggregation event ErrorDebugging link-aggregation event 489 Aggregation group 10 was removed Aggregation group 10 existed. It contained Ethernet 1/1# Remove aggregation group Operation key of port Ethernet 1/1 Key 1 was removed Modem Modem Configuration CommandsModem auto-answer Modem timer answer Syntax modem timer answer time Undo modem timer answer Sendat Sendat command can issue only one AT command at a timeWith caution under the guidance of technicians Specifies the communication standard to be adopted Syntax service modem-callback Service modem-callbackExample # Send dialing command to call number 495 Undo service modem-callback Example # Enable the callback function Mirroring-group Port Mirroring Configuration CommandsDisplay mirroring-group Syntax display mirroring-group groupid local Mirroring-group mirroring-port Undo mirroring-group groupid local Mirroring-group monitor-port 499 Mirroring-port # Add POS 5/1 to local port mirroring group # Add Cpos 6/1 to local port mirroring group Monitor-port501 Port Mirroring Configuration Commands Display interface mp-group PPP and MP Configuration 31 CommandsSyntax display interface mp-group mp-number Syntax display interface virtual-template number Related command interface virtual-templateDisplay interface virtual-template Example # View the information about VT Link-protocol ppp , ppp mp Description on the fields of the display ppp mp commandDisplay ppp mp 505 Display virtual-access For description on the output fields, refer to Table Interface mp-group 507 Interface virtual-template Ip address ppp-negotiate Undo ppp account-statistics enable Ppp account-statistics enablePpp account-statistics enable Link-protocol ppp Undo ppp authentication-mode Ppp authentication-modePpp authentication-mode chap pap call-in domain isp-name Chap, pap Authentication modes. Use either mode Ppp chap user Ppp chap passwordRelated command ppp authentication-modechap Syntax ppp chap user username Ppp ipcp dns Related command ppp authentication-modeUndo ppp chap user Syntax ppp ipcp dns admit-any Undo ppp ipcp dns admit-any Ppp ipcp dns admit-anyPpp ipcp dns request Syntax ppp ipcp dns request Undo ppp ipcp dns request Related command remote address Ppp ipcp remote-address forced Undo ppp lqc Ppp lqc515 Syntax ppp mp Ppp mpPpp mp binding-mode Undo ppp mp Ppp mp max-bind max-bind-num Related command Ppp mp user ExamplePpp mp max-bind Undo ppp mp max-bind Ppp mp min-bind min-bind-num Related command Ppp mp ExamplePpp mp min-bind Undo ppp mp min-bind Ppp mp min-fragment size Related command dialer threshold onPpp mp min-fragment Undo ppp mp min-fragment Syntax ppp mp mp-group number Undo ppp mp Ppp mp mp-groupPpp mp user Example # Add interface Serial 3/0 to MP-group Syntax ppp mp virtual-template number Undo ppp mp Related command ppp mp and ppp mp max-bindPpp mp virtual-template 521 Syntax ppp timer negotiate seconds Undo ppp timer negotiate Ppp timer negotiateRelated command local-useron page 1940, password on Ppp pap local-user Undo remote address Remote address523 Timer hold Display ppp compression iphc rtp PPP Link Efficiency Mechanism Configuration CommandsDisplay ppp compression iphc tcp Ip tcp vjcompress Display ppp compression stac-lzsSyntax ip tcp vjcompress Undo ip tcp vjcompress Ppp compression iphc 527 Ppp compression iphc rtp-connections Ppp compression stac-lzs Ppp compression iphc tcp-connections529 Ppp mp lfi Syntax ppp mp lfi Undo ppp mp lfi Reset ppp compression iphc Ppp mp lfi delay-per-frag531 PPP Link Efficiency Mechanism Configuration Commands Display pppoe-server session Pppoe Server Configuration CommandsDisplay pppoe-server session all packet Pppoe-server bind Pppoe-server log-information off Pppoe-server max-sessions remote-mac Pppoe-server max-sessions local-mac535 Pppoe-server max-sessions total number Reset pppoe-serverPppoe-server max-sessions total Undo pppoe-server max-sessions total 537 Pppoe Server Configuration Commands Pppoe Client Configuration Commands Display pppoe-client session Pppoe-client dial-bundle-number Reset pppoe-client all dial-bundle-number number Reset pppoe-clientRelated command Reset pppoe-client Related command pppoe-client Sysname reset pppoe-client all PPP Debugging Commands Debugging ppp Description on the fields of the debugging ppp event command Description on the fields of the debugging ppp ipcp command 545 LCP moved from the initial state to the starting state Description on the fields of the debugging ppp ipcp commandLCP moved from the starting state to the reqsent state 547 PPP Debugging Commands Syntax bridge bridge-setenable Undo bridge bridge-setenable Bridging Configuration CommandsBridge bridge-set enable Bridge aging-time # Enable IP bridging on bridge set Bridge enableExample # Enable bridge set Syntax bridge enable Undo bridge enable Bridge mac-address Example # Enable bridgingBridge learning 551 Bridge routing Bridge-set Bridge routing-enableSyntax bridge routing-enable Undo bridge routing-enable Syntax bridge-set bridge-set Undo bridge-set bridge-set Display bridge address-table 555 Display bridge informationSyntax display bridge information bridge-set bridge-set Dynamic S--STATIC Display bridge traffic Syntax display interface bridge-template interface-number Display interface bridge-template557 Syntax fr map bridge dlci broadcast Undo fr map bridge dlci Fr map bridgeUP/DOWN Interface bridge-template Related command display fr map-infoonBridge routing-enable Parameters Map bridge-group Related command interface bridge-templateMac-address bridge-template interface view Syntax mac-address mac-address Undo mac-address Reset bridge traffic Reset bridge address-table561 Undo x25 map bridge x121-address x.121-address X25 map bridgeX25 map bridge x121-address x.121-address broadcast Display x25 map on Dialer isdn-leased 128k number Isdn Configuration CommandsDialer isdn-leased Isdn BRI interface view Undo dialer isdn-leased 128k number Display isdn active-channel Display isdn call-info Example # Display the current state of Isdn interface 2/0 565 Display isdn call-record Display isdn parameters 567 Kbri Display isdn spidIsdn Kpri Isdn bch-local-manage 569 Isdn bch-select-way Bch-local-manage command on the user sideChannels in ascending order by default Isdn caller-number Undo isdn calling Isdn callingIsdn check-called-number Undo isdn check-called-number check-index Isdn check-time Syntax isdn check-time date-time Undo isdn check-time Undo isdn crlength Isdn crlengthIsdn ignore connect-ack Syntax isdn ignore connect-ack Undo isdn ignore connect-ack Settings must be the same as those on the exchangeIsdn ignore hlc Isdn ignore hlc Isdn ignore llc Isdn ignore llcVoice calls placed on the BRI interface 1/0 Undo isdn ignore llc Isdn ignore sending-complete incoming outgoing ConfiguredIsdn ignore sending-complete Undo isdn ignore sending-complete incoming outgoing Description of Q931 timers Isdn L3-timerUndo isdn L3-timer all timer-name Value range Default Timer-name Seconds Syntax isdn link-mode p2p Undo isdn link-mode Isdn link-modeIsdn number-property View Isdn BRI interface 579 Types and code schemes of Isdn numbersProtocol Field Bit value Definition Type Code scheme NTT Qsig Set the type and code scheme of Isdn numbers 581 Isdn overlap-sending Calls Isdn pri-slipwnd-size 583 Isdn protocol-type Isdn protocol-modeSyntax isdn protocol-type protocol Undo isdn protocol-type Syntax isdn q921-permanent Undo isdn q921-permanent Isdn q921-permanentExample # Apply Isdn Etsi on interface BRI 1/0 View Isdn BRI interface view Syntax isdn send-restart Undo isdn send-restart Isdn send-restartIsdn spid autotrigger Syntax isdn spid autotrigger Isdn spid nit Isdn spid timerSyntax isdn spid timer seconds Undo isdn spid timer Syntax isdn spid nit Undo isdn spid nit Isdn spid service audio data speech Isdn spid serviceUndo isdn spid service Syntax isdn spid resend times Undo isdn spid resend Isdn spid resendIsdn spid1 Syntax isdn spid1 spid LDN Undo isdn spid1 Isdn spid2Syntax isdn spid2 spid LDN Undo isdn spid2 Spid String of 1 to 20 digits Configuration of the Isdn calling commandThis command applies only on NI-compliant BRI interfaces LDN Local dialing number, a string of 1 to 30 digits Isdn two-tei Syntax isdn two-tei View BRI interface view Permanent-activeUndo isdn two-tei Syntax permanent-active Undo permanent-active Power-source Syntax power-source Undo power-source # Bring up BRI 2/0 595 Isdn Configuration Commands Check region-configuration Mstp Configuration CommandsActive region-configuration Syntax active region-configuration Brief Displays brief information Display stpPort number Information Related commands reset stp 599 Abnormally blocked ports Display stp abnormal-portDisplay stp abnormal-port Root guard action Syntax display stp down-port Display stp down-portDisplay stp history Syntax display stp instance instance-id history Display stp region-configuration Syntax display stp region-configuration Display stp root Related commands stp region-configurationDescription on the fields of the display stp root command Syntax display stp root Sent Display stp tcModel Tree instance, in port name order Examples # Map Vlan 2 to MST instance InstanceRegion-name Syntax region-name name Undo region-name Reset stp interface interface-list Reset stpDisplay stp Stp Syntax stp enable disable Undo stpRevision-level Syntax revision-level level Undo revision-level # Disable Mstp on port Ethernet 1/1 Related commands stp modeExamples # Enable the Mstp feature globally Stp bpdu-protection Stp bridge-diameter Stp compliance Stp config-digest-snooping Stp cost Stp edged-port Stp edged-port enable disableOr undo stp edged-port enable command to non-edge port Undo stp edged-port Stp max-hops Examples # Configure port Ethernet 1/1 as a non-edge portStp loop-protection Syntax stp loop-protection Undo stp loop-protection Stp mcheck Syntax stp mcheck Stp no-agreement-check Stp modeStp mcheck , stp View System view Parameters Examples # Enable No Agreement Check on Ethernet 1/1Stp pathcost-standard 802.1D-1998 Stp point-to-point 617 Stp port-log Stp port priority 619 Stp instance instance-id priority priority Stp priorityUndo stp instance instance-id priority Stp region-configuration Stp root primary Stp root secondary Stp instance instance-id root secondary Stp tc-protection Syntax stp tc-protection enable Stp tc-protection disableStp root-protection Syntax stp root-protection Undo stp root-protection Stp timer forward-delay Stp tc-protection threshold Syntax stp timer hello centi-seconds Undo stp timer hello Stp timer hello625 Stp timer max-age Syntax stp timer-factor number Undo stp timer-factor Stp timer-factor627 Vlan-mapping modulo Stp transmit-limitSyntax vlan-mapping modulo modulo Examples # Map VLANs to MSTIs as per the modulo value 629 Mstp Configuration Commands Display interface vlan-interface Vlan Configuration CommandsSyntax display interface vlan-interface vlan-interface-id Vlan interfaces will be displayed Vlan-interface-id Vlan interface ID# Display the information of VLAN-interface Example # Display Vlan 2 information Related command vlanDisplay vlan # Display Vlan 3 information Interface vlan-interface Related command display interface vlan-interfaceDescription on the fields of the display vlan command Example # Create Vlan interface Ip address Related command display ip interface on635 Vlan View Vlan interface view # Create Vlan 4 through Vlan Related command display vlanExample # Enter Vlan 2 view 637 Vlan Configuration Commands Syntax port access vlan vlan-id Undo port access vlan PORT-BASED Vlan Configuration CommandsPort access vlan Port Port hybrid pvid vlan Related command port link-typeSyntax port hybrid pvid vlan vlan-id Undo port hybrid pvid Port hybrid vlan 641 Port link-type Port trunk permit vlan Syntax port trunk pvid vlan vlan-id Undo port trunk pvid Port trunk pvid vlan643 Related command port link-type Voice Vlan Configuration Commands Display voice vlan state Voice vlan enable ExampleSyntax voice vlan vlan-idenable Voice vlan Voice vlan aging Undo voice vlan enableRelated command display voice vlan state Syntax voice vlan aging minutes Undo voice vlan aging Syntax voice vlan enable Undo voice vlan enable Voice vlan enableVoice vlan mac-address Be a broadcast, multicast or address of all 0s or all fs Ffff-f000-0000Range of 1 to 30 characters Display voice vlan oui Example Voice vlan security enable Voice vlan mode autoSyntax voice vlan mode auto Undo voice vlan mode auto Example # Disable the security mode of the voice Vlan 651 Voice Vlan Configuration Commands Syntax port-isolate enable Undo port-isolate enable Port Isolation Configuration CommandsPort-isolate enable Display port-isolate group Port Isolation Configuration Commands Standby routing-group Dynamic Route Backup Configuration CommandsStandby routing-rule Standby timer routing-disable Display interface loopback Logical Interface Configuration CommandsBroadcast-limit link Syntax display interface loopback number Example # View the status of Loopback Related command interface loopbackSyntax display interface mfr mfr-number 659 Related command interface mfrExample # View the state information about MFR LMI Dlci Related command interface mp-group Example # View the state information of MP-group Display interface virtual-ethernet Related command interface nullDisplay interface null Syntax display interface null Example # View the state information about VE Related command interface virtual-ethernetExample # View the state information about VT Description of the fields of the display mfr command 663 Interface, state of the link layer, and the name Interface ethernet 665 Interface loopback Related command display interface loopbackExample # Create Loopback Example # Create MP-group Interface nullExample # Create MFR Interface null Interface virtual-ethernet Related command display interface nullExample # Enter Null 0 interface view 669 Logical Interface Configuration Commands Controller cpos Cpos Interface Configuration CommandsSystem view Display controller cpos Display controller cpos cpos-number Possible error types This table, FRED, COFA, and SEF are alarm errors AERRs673 Some information about T1 channels is omitted Display controller cpos e1Syntax display controller cpos cpos-numbere1 e1-number Syntax display controller cpos cpos-numbert1 t1-number Display controller cpos t1675 VC-3 Example # Bundle timeslots on E1 channel 677 E1 set clock Example # Enable external payload loopback on E1 channel Related command display controller cpos e1679 Syntax e1 e1-numbershutdown undo e1 e1-numbershutdown Syntax e1 e1-numberunframed undo e1 e1-numberunframed Display controller cpos Undo flag j0 j1 c2Syntax frame-format sdh sonet undo frame-format # Enable external loopback on interface Cpos 1/0 Multiplex modeUse the undo loopback command to remove a loopback Syntax multiplex mode au-3 au-4 undo multiplex mode Example # In SDH mode, multiplex AUG to AU-3 Related command frame-format683 Example # Shut down Cpos physical interface 1/0 Example # Bundle timeslots on T1 channel 685 Example # Enable external loopback on T1 channel Related command display controller cpos t1Syntax t1 t1-numbershutdown Undo t1 t1-numbershutdown Syntax t1 t1-numberunframed Undo t1 t1-numberunframed 687 Cpos Interface Configuration Commands Syntax arp check enable Undo arp check enable ARP Configuration CommandsArp check enable Arp max-learning-num Arp static Related command display arp timer aging Arp timer agingRelated command reset arp, display arp Display arp Description on the fields of the display arp command Related command arp static, reset arp# Display the number of all ARP entries Display arp timer aging Display arp timer agingArp static , and reset arp Example Arp timer aging Syntax naturemask-arp enable Undo naturemask-arp enable Naturemask-arp enableRelated command arp static and reset arp Display arp vpn-instance Specified by the argument interface-type interface-number Reset arpArp static and display arp ARP Configuration Commands Gratuitous-arp-learning enable Gratuitous ARP Configuration CommandsGratuitous-arp-sending enable Gratuitous-arp-sending enable Sysname system-view Sysname gratuitous-arp-learning enable Arp source-suppression limit ARP Source Suppression Configuration CommandsArp source-suppression enable Display arp source-suppression Syntax display arp source-suppression Related command display arp source-suppressionDisplay arp source-suppression Description on fields of display arp source-suppression Syntax arp authorized enable Undo arp authorized enable Authorized ARP Configuration CommandsArp authorized enable Arp authorized time-out Authorized ARP Configuration Commands Local-proxy-arp enable Proxy ARP Configuration CommandsProxy-arp enable Related command display proxy-arp Local-proxy-arp enable Related command display local-proxy-arpProxy-arp enable Display proxy-arp Dhcp Server Configuration Commands Syntax bootfile-name bootfile-name Undo bootfile-name Bootfile-nameDhcp enable Syntax dhcp enable Undo dhcp enable Syntax dhcp server detect Undo dhcp server detect Dhcp select server global-poolDhcp server detect 707 Dhcp server forbidden-ip Dhcp server ip-pool Dhcp server ping packets Dhcp server ping timeoutRelated command dhcp enable Example # Create the Dhcp address pool identified by Dhcp update arp Dhcp server relay information enableSyntax dhcp update arp Undo dhcp update arp Display dhcp server expired Reset dhcp server conflictDisplay dhcp server conflict Display dhcp server conflict all ip ip-address Display dhcp server free-ip Display dhcp server free-ipDisplay dhcp server forbidden-ip Syntax display dhcp server forbidden-ip Binding information of all address pools is displayed Reset dhcp server ip-in-useDisplay dhcp server ip-in-use Information of Dhcp address pools or an IP address Syntax display dhcp server statistics Reset dhcp server statisticsDisplay dhcp server statistics Example # Display the statistics on the Dhcp server Information of Dhcp address pools Display dhcp server treeDisplay dhcp server tree all pool pool-name 715 Dns-list Undo dns-list ip-addressall Domain-name Related command dhcp server ip-poolExpired Gateway-list Nbns-list Netbios-typeRelated command dhcp server ip-pooland netbios-type 719 Network Related command dhcp server ip-pooland nbns-listUndo network Undo option code Option721 Reset dhcp server ip-in-use Reset dhcp server conflictReset dhcp server statistics Example # Clear the statistics of the Dhcp server Related command display dhcp server statisticsStatic-bind client-identifier 723 Static-bind ip-address Tftp-server domain-name Static-bind mac-address725 Tftp-server ip-address Voice-configUndo voice-config as-ip fail-over ncp-ip voice-vlan View Dhcp address pool view 727 Dhcp Server Configuration Commands Syntax dhcp relay address-check disable enable Dhcp Relay Agent Configuration CommandsDhcp Snooping cannot be configured on the Dhcp relay agent Dhcp relay address-check Dhcp relay information enable Dhcp relay information format Dhcp relay information strategy drop keep replace Dhcp relay information strategyUndo dhcp relay information strategy Syntax dhcp relay release ip client-ip Dhcp relay release ipDhcp relay security static Undo dhcp relay security ip-address all dynamic static Dhcp relay security tracker Related command display dhcp relay security733 Dhcp relay server-detect Dhcp relay server-detectDhcp relay server-group Undo dhcp relay server-detect Dhcp relay server-select Related command display dhcp relay server-group735 Dhcp select relay Dhcp update arpDhcp select relay Undo dhcp select relay Server group that a specified interface corresponds to Display dhcp relayDisplay dhcp relay security Groups correlated to an interface or all interfaces Display dhcp relay security statistics Display dhcp relay security statisticsDisplay dhcp relay security tracker Information about bindings of Dhcp relay agents Interval is 10 seconds Display dhcp relay server-groupDisplay dhcp relay statistics Syntax display dhcp relay server-group group-idall Server Client Which to remove statistics from the relay agent Reset dhcp relay statisticsReset dhcp relay statistics server-group group-id Display dhcp relay statistics Dhcp Relay Agent Configuration Commands Dhcp Client Configuration Commands Description on fields of the display dhcp client command Ip address dhcp-alloc 745 Dhcp Client Configuration Commands Dhcp-snooping Dhcp Snooping Configuration CommandsRelated command display dhcp-snooping Dhcp-snooping trust Display dhcp-snooping trust Related command display dhcp-snooping trustDisplay dhcp-snooping Dhcp-snooping # Display information about trusted ports Related command dhcp-snooping trust ExampleTrusted ports 749 Dhcp Snooping Configuration Commands Display information about Bootp clients on all interfaces Bootp Client Configuration CommandsBootp client Including sub-interfaces and Vlan interfaces Related command display bootp client Ip address bootp-allocSyntax ip address bootp-alloc Undo ip address bootp-alloc Description on fields of the display bootp client command Undo debugging dhcp server all error event packet Dhcp Debugging CommandsDebugging dhcp server all error event packet Debugging dhcp server DHCPmessagetype Dhcp ACK Dhcp NAK DHCP-DISCOVER packet received Checking for an expired lease755 Checking whether the IP address 22.0.0.2 is in use DHCP-REQUEST message received Debugging dhcp relay Sending a DHCP-ACK message Sysname Terminal debugging 759 Debugging dhcp client Debugging dhcp client all error event packetUndo debugging dhcp client all error event packet Then broadcast it 761 State of the Dhcp client is changed from Halt to Init 763 Head Dhcp client starts address conflict detection using ARP ARP message sent Display dns dynamic-host DNS Configuration CommandsDisplay dns domain Dns domain Example Syntax display dns proxy table Display dns proxy tableTTL Display ip host Related command dns serverDisplay dns server Syntax display dns server dynamic Syntax dns proxy enable Undo dns proxy enable Dns proxy enableRelated command display dns domain Dns domain Syntax dns resolve Undo dns resolve Dns resolveDns server Syntax dns server ip-address Undo dns server ip-address Related command display ip host Reset dns dynamic-hostRelated command display dns server Syntax reset dns dynamic-host Related command display dns dynamic-host 771 DNS Configuration Commands Display ip count inbound-packets outbound-packets exterior IP Accounting Configuration CommandsDisplay ip count Firewall-denied interior Description on fields of the display ip count rule command Ip count enableSyntax ip count enable Undo ip count enable Display ip count rule Ip count firewall-denied Example # Enable IP accountingIp count exterior-threshold 775 Ip count inbound-packets # Specify not to count incoming IP packets on Ethernet1/0 Ip count interior-thresholdExample # Count incoming IP packets on Ethernet1/0 777 Ip count outbound-packets Ip count rule Syntax ip count timeout minutes Undo ip count timeout Ip count timeoutReset ip count Syntax reset ip count all exterior firewall interior Interior Clears the statistics from the interior table All Clears all statisticsExterior Clears the statistics from the exterior table # Clear the statistics of all IP packets IP Addressing Configuration Commands Display ip interface Description on fields of the display ip interface command Example # Display brief information about Ethernet 1/0 Related command display ip interfaceDisplay ip interface brief 783 Displayed Ip address unnumbered 785 IP Addressing Configuration Commands IP Performance Configuration Commands Display fib # Display FIB information passing ACL Description on the fields of the display fib command# Display FIB information passing the IP prefix list abc0 For description about the above output, refer to Table Display fib ip-addressDisplay fib statistics Syntax display fib statistics Syntax display icmp statistics Display icmp statisticsExample # Display Icmp statistics 3072 Display ip socket100 # Display all socket information Display ip statistics Description on the fields of the display ip socket commandSyntax display ip statistics Syntax display tcp statistics Display tcp statisticsExample # Display statistics of IP packets 793 Related command display tcp status and reset tcp statistics Example # Display statistics of TCP traffic 795 Display udp statistics Related command reset udp statisticsDisplay tcp status Display tcp status Ip forward-broadcast acl acl-number Ip forward-broadcastUndo ip forward-broadcast Ip redirects enable Ip ttl-expires enable Reset ip statistics Ip unreachables enableReset tcp statistics Related command display tcp statistics Reset udp statisticsTcp anti-naptha enable Syntax reset udp statistics Tcp mss Tcp state This support for this command varies with devices Tcp syn-cookie enableRelated command tcp anti-naptha enable Syntax tcp syn-cookie enable Undo tcp syn-cookie enable Example # Enable the SYN Cookie feature Tcp timer check-stateTcp timer fin-timeout 803 Related command tcp timer syn-timeoutand tcp window Tcp timer syn-timeoutRelated command tcp timer fin-timeoutand tcp window Syntax tcp window window-size Undo tcp window Tcp window805 IP Performance Configuration Commands Apply ip-address default next-hop IP Unicast Policy Routing Configuration CommandsApply default output-interface View policy-based-route view Apply ip-address next-hop Parameters ip-address IP address of the default next hopUndo apply ip-address next-hop ip-address ip-address IP precedences and the corresponding keywords Apply ip-precedenceExamples # Set the next hop to 1.1.1.1 for matched packets 809 Display ip policy-based-route Apply output-interfaceSyntax display ip policy-based-route Display ip policy-based-route setup 811 Interface-number Local Displays statistics of enabled system policy routingDisplay ip policy-based-route statistics Routing statistics If-match acl Related commands if-matchpacket-lengthDisplay policy-based-route Syntax display policy-based-route policy-name If-match packet-length Related commands if-match aclIp local policy-based-route Ip policy-based-route Related commands policy-based-routeRelated commands ip local policy-based-route Policy-based-route Related commands if-match acl and if-matchpacket-length Reset policy-based-route statisticsSyntax reset policy-based-route statistics policy-name 817 IP Unicast Policy Routing Configuration Commands Reset udp-helper packet UDP Helper Configuration CommandsReset udp-helper packet Display udp-helper server Syntax udp-helper enable Undo udp-helper enable Udp-helper enableUdp-helper port Udp-helper server Related command display udp-helper server821 UDP Helper Configuration Commands Ip urpf Urpf Configuration CommandsIp urpf loose strict allow-default-route acl acl-number Undo ip urpf Urpf Configuration Commands Ip fast-forwarding Fast Forwarding CommandsDisplay ip fast-forwarding cache Display ip fast-forwarding cache Fast Forwarding Commands Syntax reset ip fast-forwarding cache Reset ip fast-forwarding cache827 Fast Forwarding Commands Display dns ipv6 server IPV6 Basics Configuration CommandsDisplay dns ipv6 dynamic-host Syntax display dns ipv6 dynamic-host Example # Display IPv6 DNS server information Display ipv6 fibSyntax display ipv6 fib ipv6-address Display ipv6 host Description on fields of the display ipv6 fib commandDisplay ipv6 fibcache Syntax display ipv6 fibcache Display ipv6 interface Shutdown command 833 Display ipv6 neighbors Display ipv6 neighbors count Static vlan vlan-id count Display ipv6 socket Description on fields of the display ipv6 pathmtu commandDisplay ipv6 pathmtu Syntax display ipv6 pathmtu ipv6-addressall dynamic static Syntax display ipv6 statistics Description on fields of the display ipv6 socket commandDisplay ipv6 statistics 837 Description on fields of the display ipv6 statistics command 839 Statistics Display tcp ipv6 statisticsDisplay tcp ipv6 statistics # Display the statistics of IPv6 TCP connections 841 Display tcp ipv6 status Syntax display tcp ipv6 status 843 Display udp ipv6 statisticsSyntax display udp ipv6 statistics TCP6CB Syntax ipv6 Dns server ipv6Ipv6 Undo ipv6 Ipv6 address auto link-local Ipv6 address845 Ipv6 address eui-64 Ipv6 address link-local Syntax ipv6 fibcache Undo ipv6 fibcache Ipv6 fibcacheIpv6 fib-loadbalance-type hash-based 847 Ipv6 icmp-error Ipv6 host Syntax ipv6 mtu mtu-size Undo ipv6 mtu Ipv6 icmpv6 multicast-echo-reply enableIpv6 mtu 849 Ipv6 nd autoconfig managed-address-flag Ipv6 nd autoconfig managed-address-flagIpv6 nd autoconfig other-flag Undo ipv6 nd autoconfig managed-address-flag Syntax ipv6 nd dad attempts value Undo ipv6 nd dad attempts Ipv6 nd dad attemptsIpv6 nd hop-limit Syntax ipv6 nd hop-limit value Undo ipv6 nd hop-limit Ipv6 nd ns retrans-timer Ipv6 nd nud reachable-time On a router # Suppress RA messages on Ethernet1/0 Ipv6 nd ra haltSyntax ipv6 nd ra halt Undo ipv6 nd ra halt 853 Undo ipv6 nd ra interval Ipv6 nd ra intervalIpv6 nd ra prefix Undo ipv6 nd ra prefix ipv6-prefix Ipv6 nd ra router-lifetime 855 Ipv6 neighbor Undo ipv6 pathmtu ipv6-address Ipv6 neighbors max-learning-numIpv6 pathmtu 857 Syntax reset dns ipv6 dynamic-host Reset dns ipv6 dynamic-hostRelated command display ipv6 pathmtu Ipv6 pathmtu age Reset ipv6 neighbors Reset ipv6 fibcacheReset ipv6 pathmtu Reset udp ipv6 statistics Reset ipv6 statisticsReset tcp ipv6 statistics ICMPv6 packets Example # Clear the statistics of all UDP packets Tcp ipv6 timer fin-timeoutTcp ipv6 timer syn-timeout 861 Tcp ipv6 window Syntax tcp ipv6 window size Undo tcp ipv6 window Display natpt address-mapping NAT-PT Configuration CommandsDisplay natpt address-group Display natpt address-group Display natpt aging-time Syntax display natpt aging-time Display natpt all Example # Display all NAT-PT configuration informationDisplay natpt all 865 Display natpt frag-sessions Syntax display natpt frag-sessions Syntax display natpt session all icmp tcp udp Display natpt sessionDisplay natpt statistics Display natpt statistics Natpt address-group Undo natpt address-group group-number Natpt aging-time Natpt max-session Natpt enableSyntax natpt enable Undo natpt enable Syntax natpt max-session max-number Undo natpt max-session Undo natpt prefix natpt-prefix Example # Configure a NAT-PT prefixNatpt prefix 871 Natpt turn-off tos Natpt turn-off tosNatpt turn-off traffic-class Undo natpt turn-off tos Natpt v4bound static Natpt v4bound dynamic873 Natpt v6bound dynamic Natpt v6bound static Reset natpt dynamic-mappingsSyntax reset natpt dynamic-mappings Undo natpt v6bound static ipv6-addressipv4-address Reset natpt statistics Reset natpt statistics# Clear all NAT-PT statistics information Dual Stack Configuration Commands Automatically created link-local address Ipv6 address auto link-localAutomatically create a link-local address for an interface Ethernet interface view Example # Configure a link-local address on Ethernet 1/1 879 Dual Stack Configuration Commands Destination Tunneling Configuration CommandsRelated command interface tunnel and source Undo destination Syntax display interface tunnel number Display interface tunnelExample # Display information of the interface tunnel Syntax display ipv6 interface tunnel number Display ipv6 interface tunnel883 Syntax encapsulation-limit number Undo encapsulation-limit Encapsulation-limitInterface tunnel Syntax interface tunnel number Example # Create the interface tunnel Undo interface tunnel number885 Source Related command interface tunnel and destinationUndo source Ipv4-ipv6 Tunnel-protocolUndo tunnel-protocol Tunneling Configuration Commands Apply destination-based-forwarding IPV6 Unicast Policy Routing Configuration CommandsView IPv6 policy-based-route view Apply ipv6-address default next-hop Example # Set a next hop of 11 for matched IPv6 packets Apply ipv6-address next-hopApply ipv6-precedence Preferences and the corresponding keywords Apply output-interface Display ipv6 policy-based-route Display ipv6 config policy-based-routeSyntax display ipv6 config policy-based-route policy-name Display ipv6 policy-based-route Display ipv6 policy-based-route setup Local Displays system policy routing information If-match acl6 Related command if-matchpacket-lengthDisplay ipv6 policy-based-route statistics Syntax if-match acl6 acl6-number Undo if-match acl6 Ipv6 local policy-based-route Related command if-match acl6Example # Permit the packets matching ACL Ipv6 policy-based-route system view Related command ipv6 local policy-based-routeIpv6 policy-based-route interface view 897 IPV6 Unicast Policy Routing Configuration Commands Auto-link Terminal Access Configuration CommandsAuto-close Syntax auto-close time Undo auto-close Bind vpn-instance Syntax bind vpn-instance vpn-name Undo bind vpn-instance View Terminal template view Data protect router-unixData read block Syntax data read block Undo data read block Syntax data send delay milliseconds Undo data send delay Data send delayDisplay rta # Display brief information about TTY 903 TTY # Display statistics about terminal # Display all the information about terminal accessDescription on the fields of the display rta all command 905 Driverbuf size # Display terminal access statisticsDriverbuf save Syntax driverbuf save Undo driverbuf save Undo driverbuf size Idle-timeoutSyntax idle-timeout seconds Undo idle-timeout 907 Menu screencode Related command print information and print menuMenu hotkey Syntax menu hotkey ascii-code&1-3 Undo menu hotkey Syntax print connection-info Undo print connection-info Print connection-info909 Print information Related command print informationRelated command print connection-infoand print menu Print menu Print language chinese english Print languageRedrawkey Terminal template view Reset rta statistics Reset rta connectionReset rta statistics terminal-number Undo resetkey ResetkeyRelated command display rta Rta bind Rta rtc-server listen-port Rta source-ip Rta server enableSyntax rta server enable Undo rta server enable Syntax rta source-ip ip-address Undo rta source-ip Hiding Rta templateRta terminal TCP connections Syntax sendbuf bufsize size Undo sendbuf bufsize Sendbuf bufsize917 Tcp Sendbuf thresholdSyntax sendbuf threshold value Undo sendbuf threshold # Set the TCP send buffer size to 512 bytes # Disable TCP delayTestkey Undo testkey Update changed-config Update changed-configAccess Values are used for the hotkeys of flow control Undo vty vty-numberdescription Vty descriptionVty hotkey 921 Vty password Vty rtc-server remote Vty rtc-client remote923 Vty screencode Related command menu screencodeUndo vty vty-numberscreencode Example # Set the screen code for VTY 1 to E!9Q Vty telnet remoteVty tty remote 925 Syntax vty-switch priority Undo vty-switch priority Vty-switch priorityVty-switch threshold Syntax vty-switch threshold times Undo vty-switch threshold 927 Terminal Access Configuration Commands Display ip routing-table IP Routing Table CommandsBandwidth-based-sharing Syntax bandwidth-based-sharing Undo bandwidth-based-sharing Special characters for regular expressions String, the end of a string 931 Display ip routing-table acl Syntax display ip routing-table acl acl-number verbose 933 IP Routing Table Commands Display ip routing-table ip-address 935 Display ip routing-table ip-addresslonger-match Display ip routing-table ip-addressDisplay ip routing-table ip-address mask Display ip routing-table ip-address mask longer-match 937 Display ip routing-table ip-prefix For detailed description of the above output, see Table Display ip routing-table protocol939 # Display summary information about static routes Display ip routing-table statisticsView Any view Display ip relay-route vpn-instance vpn-instance-name Display ip relay-routeDisplay ip relay-tunnel # Display recursive route information Examples # Display recursive tunnel information Display load-sharing ip addressDisplay ipv6 routing-table Syntax display ipv6 routing-table Syntax display ipv6 routing-table acl acl6-number verbose Display ipv6 routing-table acl943 Refer to for description about the above output Display ipv6 routing-table ipv6-addressDisplay ipv6 routing-table ipv6-addressprefix-length Display ipv6 routing-table ipv6-address1 ipv6-address2 945 Display ipv6 routing-table ipv6-prefix Display ipv6 routing-table protocol # Display routing statistics Display ipv6 routing-table statisticsSyntax display ipv6 routing-table statistics 947 Display ipv6 routing-table verbose Display ipv6 routing-table verboseDisplay ipv6 relay-route Entire routing table and information for each route # Display IPv6 recursive tunnel information Display ipv6 relay-tunnelDisplay ipv6 relay-tunnel 949 Load-bandwidth Reset load-sharingSyntax load-bandwidth bandwidth Undo load-bandwidth Reset ipv6 routing-table statistics protocol all protocol Reset ip routing-table statistics protocolReset ipv6 routing-table statistics Ripng , or static Sysname reset ipv6 routing-table statistics protocol all Aggregate BGP Configuration CommandsConfiguration Commands on Functions of the keywords Syntax balance number Undo balance If-match clause of the route-policy commandBalance BGP/BGP-VPN instance view Suppress-policy View BGP view/BGP-VPN instance view Related commands display bgp routing-tableBestroute as-path-neglect BGP/BGP-VPN instance view 955 Bestroute med-confederation BGP/BGP-VPN instance view Comparison is not enabled by defaultBestroute compare-med BGP/BGP-VPN instance view Syntax bestroute compare-med Undo bestroute compare-med Compare-different-as-med BGP/BGP-VPN instance view Bgp957 Confederation id Syntax confederation id as-number Undo confederation id Confederation peer-as Related commands confederation id and confederation peer-asConfederation nonstandard View BGP view Examples # Specify confederation peer sub ASs 2000 Dampening BGP/BGP-VPN instance viewUndo confederation peer-as as-number-list Undo dampening Syntax default ipv4-unicast Undo default ipv4-unicast Default ipv4-unicastExamples # In BGP view, configure BGP route dampening 961 Default med BGP/BGP-VPN instance view Default local-preference BGP/BGP-VPN instance viewSyntax default med med-value Undo default med Syntax default-route imported Undo default-route imported Default-route imported BGP/BGP-VPN instance view963 Display bgp group Related commands import-routeBGP/BGP-VPN instance viewDescription on the fields of the display bgp group command Syntax display bgp group group-name Display bgp network Advertised with the network commandDisplay bgp network # Display routing information that has been advertised Display bgp peer Description on the fields of the display bgp paths commandDisplay bgp paths MED Description on the fields of the display bgp peer command 967 Description on the fields of the display bgp routing command Display bgp routing-table Display bgp routing-table as-path-acl 969 Display bgp routing-table cidr Display bgp routing-table cidr Display bgp routing-table community-list Display bgp routing-table community971 Dampened BGP routes Display bgp routing-table dampenedDisplay bgp routing-table dampened # Display dampened BGP routes Display bgp routing-table different-origin-as Related commands dampening BGP/BGP-VPN instance viewDisplay bgp routing-table dampening parameter Display bgp routing-table dampening parameter Display bgp routing-table flap-info Longer-match Display bgp routing-table peer Related commands display bgp peer975 Ebgp-interface-sensitive Display bgp routing-table regular-expressionDisplay bgp routing-table statistic Display bgp routing-table statistic Undo ebgp-interface-sensitive Filter-policy export BGP/BGP-VPN instance view977 Filter-policy import BGP/BGP-VPN instance view Syntax graceful-restart Undo graceful-restart Graceful-restart timer restartGraceful-restart BGP view 979 Undo graceful-restart timer wait-for-rib Graceful-restart timer wait-for-ribGraceful-restart timer wait-for-rib timer Using this command can speed up route convergence Import-route BGP/BGP-VPN instance view 981 Log-peer-change Syntax log-peer-change Undo log-peer-change Network BGP/BGP-VPN instance view 983 Peer advertise-community BGP/BGP-VPN instance view Peer advertise-ext-community BGP/BGP-VPN instance view Peer allow-as-loop BGP/BGP-VPN instance view Related commands display bgp routing-table peer985 Peer as-path-acl BGP/BGP-VPN instance view Peer as-number BGP/BGP-VPN instance viewUndo peer ip-address Peer capability-advertise conventional 987 Peer capability-advertise route-refresh Peer connect-interface BGP/BGP-VPN instance view Peer default-route-advertise BGP/BGP-VPN instance viewUndo peer group-nameip-address default-route-advertise Undo peer group-name ip-address connect-interface Peer description BGP/BGP-VPN instance view Peer ebgp-max-hop BGP/BGP-VPN instance view 991 Syntax peer ip-addressenable Undo peer ip-addressenable Peer enable BGP viewPeer fake-as BGP/BGP-VPN instance view Peer filter-policy BGP/BGP-VPN instance view Related commands peer as-path-aclBGP/BGP-VPN instance view993 Peer group BGP/BGP-VPN instance view Peer ip-prefix Peer ignore BGP/BGP-VPN instance view995 Peer keep-all-routes BGP/BGP-VPN instance view Undo peer group-name ip-address next-hop-local Peer log-change BGP/BGP-VPN instance viewPeer next-hop-local BGP/BGP-VPN instance view View BGP view /BGP-VPN instance view Peer password Undo peer group-name ip-address preferred-value # Perform the similar configuration on the peerPeer preferred-value BGP/BGP-VPN instance view 999 Peer public-as-only BGP/BGP-VPN instance view Undo peer group-name ip-address public-as-only Peer reflect-client BGP/BGP-VPN instance view 1001 Peer route-limit BGP/BGP-VPN instance view Peer route-policy BGP/BGP-VPN instance view Peer route-update-interval BGP/BGP-VPN instance view 1003 Peer substitute-as BGP/BGP-VPN instance view Undo peer group-nameip-address substitute-as Related commands timer BGP/BGP-VPN instance view Peer timer BGP/BGP-VPN instance view1005 Undo preference Preference BGP/BGP-VPN instance viewReflect between-clients BGP view Syntax reflect between-clients Undo reflect between-clients Examples # Set the cluster ID to Examples # Disable route reflection between clientsReflector cluster-id BGP view 1007 As-number Resets BGP connections to peers in the AS Reset bgpAll Resets all BGP connections Refresh bgp Reset bgp flap-info Reset bgp dampening1009 Router-id Reset bgp ipv4 allSyntax reset bgp ipv4 all Syntax router-id router-id Undo router-id Syntax summary automatic Undo summary automatic Summary automatic1011 Synchronization BGP view Timer BGP/BGP-VPN instance viewSyntax timer keepalive keepalive hold holdtime Undo timer Syntax synchronization Undo synchronization Related commands peer timer BGP/BGP-VPN instance view 1013 BGP Configuration Commands BGP Debugging Commands Debugging bgp all BGP configuration information BGP received an Open message from the peer Syntax debugging bgp detail Undo debugging bgp detail Debugging bgp detail1017 Debugging bgp event Route was deleted from the instance State has changed from Opensent to Openconfirm BGP has received an Update messageDebugging bgp graceful-restart 1019 BGP peer relationship has been successfully established BGP neighbor 10.1.1.1 is performing GRBGP GR Helper received an EOR message from peer Debugging bgp Description on the fields of the debugging bgp command1021 AFI/ Safi Description on the fields of the debugging bgp open commandInformation about the sent BGP Open message WTR Information about the received BGP Keepalive message Information about the received BGP Open messageInformation about the sent BGP Keepalive message 1023 Debugging bgp timer ConnectRetry timer for BGP peer 2.2.2.2 expired Send Enables the debugging for sent BGP packets Hold timer expired on BGP peerReceive Enables the debugging for received BGP packets Update messages Ip-prefix-name receive send verbose Debugging bgp update ipv4Ip-prefix ip-prefix-name receive send verbose Update messages of IPv4 address family Debugging bgp update ipv61027 For IPv6 BGP update messages Receive Enables/disables debugging for received BGP packetsSend Enables/disables debugging for sent BGP packets Complete By default, this debugging is disabled Verbose Debugging bgp update l2vpnUpdate messages of IPv6 address family Send verbose Acl-number ip-prefix ip-prefix-name receive send verbose Debugging bgp update label-routeUpdate messages in an L2VPN environment Receive send verbose Update message information of L3VPN labeled routes 1031 Debugging bgp update peer Update message information of IPv6 labeled routes For BGP Vpls Update messages Debugging bgp update vplsVpls Update messages 1033 Information about the sent Vpls update message Debugging bgp update vpn-instanceInformation about the received Vpls update message For BGP VPNv4 Update messages Debugging bgp update vpnv4BGP VPNv4 Update messages Examples None Update message information of VPNv4 Area-authentication-mode simple md5 password ip osi IS-IS Configuration CommandsArea-authentication-mode Undo area-authentication-mode Related commands bandwidth-referenceIS-IS view, cost-style Auto cost enableSyntax auto-cost enable Undo auto-cost enable Bandwidth-reference IS-IS view Circuit-cost Related commands auto cost enable1039 Relax-spf-limit Related commands isis cost, cost-styleCost-style Undo cost-style Related commands isis cost Default-route-advertise IS-IS view1041 Description on the fields of the display isis brief command Display isis brief Display isis debug-switches Display isis graceful-restart status Verbose Displays IS-IS interface detail information Display isis interfaceTraffic-eng Displays IS-IS traffic engineering information Tunnel Displays IS-IS tunnel information 1045 Examples # Display IS-IS enabled interface information# Display detailed IS-IS interface information DIS Syntax display isis license Display isis licenseBFD Display isis lsdb License information varies with device models Lspid Display isis mesh-groupATT/P/OL Display isis name-table # Display the configuration information of IS-IS mesh-group# Configure a static mapping for the remote IS-IS system Display isis peer # Display detailed IS-IS neighbor information Display isis routeUp state and direct interface’s IP address PRI # Display IS-IS IPv4 routing information Description on the fields of the display isis route command1051 Display isis spf-log Display isis statistics Md5 Specifies to send the password encrypted with MD5 Domain-authentication-modeSimple Specifies to send the password in plain text IS-IS view Filter-policy export IS-IS view 1055 Related commands filter-policy import IS-IS view Filter-policy import IS-IS view Level-1 level-2 Related commands filter-policy export IS-IS viewFlash-flood Undo flash-flood level-1 level-2 Graceful-restart interval IS-IS view Graceful-restart IS-IS viewGraceful-restart Graceful-restart suppress-sa Graceful-restart suppress-saImport-route IS-IS view Undo graceful-restart suppress-sa Related commands import-route isis level-2 into level-1 Examples # Redistribute static routes and set the cost to Related commands import-routeIS-IS viewImport-route isis level-2 into level-1 Undo import-route isis level-2 into level-1 Isis authentication-mode Isis Undo isis circuit-level This command is not available in loopback interface viewIsis circuit-level level-1 level-1-2 level-2 1063 Isis circuit-type Related commands is-levelSyntax isis circuit-type p2p Undo isis circuit-type Isis dis-name Syntax isis dis-name symbolic-name Undo isis dis-nameIsis cost 1065 Examples # Configure the name as Localarea for the local LAN Isis dis-priority Related commands isis, network-entity Isis enableSyntax isis enable process-id Undo isis enable Isis mesh-group Isis peer-ip-ignore Syntax isis peer-ip-ignore Undo isis peer-ip-ignore Syntax isis small-hello Undo isis small-hello Isis small-helloSyntax isis silent Undo isis silent 1069 Isis timer csnp Isis timer hello Isis timer holding-multiplier value level-1 level-2 Isis timer holding-multiplierUndo isis timer holding-multiplier level-1 level-2 Syntax isis timer lsp time count count Undo isis timer lsp Isis timer lspRelated commands isis timer hello Related commands isis timer retransmit Is-level Isis timer retransmitRelated commands Examples Isis timer lsp Syntax is-level level-1 level-1-2 level-2 Undo is-level Is-name Related commands isis circuit-levelExamples # Configure the router to work in Level-1 Syntax is-name sys-name Undo is-name Is-name map Is-snmp-traps enableSyntax is-snmp-traps enable Undo is-snmp-traps Undo is-name map sys-id Log-peer-change IS-IS view Lsp-fragments-extend Lsp-length originate 1077 Maximum load-balancing IS-IS view # Restore the defaultLsp-length receive Syntax lsp-length receive size Undo lsp-length receive Preference IS-IS view Related commands Isis, isis enable ExamplesNetwork-entity Network-entity net Reset isis all Examples # Clear all IS-IS data structure information Allow interlevel external Reset isis peerSet-overload Undo set-overload Spf-slice-size Syntax spf-slice-size duration-time Undo spf-slice-size Summary IS-IS view 1083 Generation interval Timer isp-generationUndo timer lsp-generation level-1 level-2 Interval Syntax timer lsp-max-age seconds Undo timer lsp-max-age Timer lsp-max-ageTimer lsp-refresh Related commands timer lsp-refresh Undo timer spf Timer spfRelated commands timer lsp-max-age Examples # Set the LSP refresh interval to 1500 seconds Undo virtual-system virtual-system-id Virtual-system# Set the maximum SPF calculation interval to 15 seconds 1087 IS-IS Configuration Commands Debugging isis IS-IS Debugging CommandsEvent Enables IS-IS event debugging Ha-events interface-information memory-allocating IS-IS Debugging Commands 1091 Snpa Snpa Field CircuitName not enabled 1093 SNP packet length mismatch 1095 Length length Updt Reset Required 1097 Sending pduLevel pduType on circuitName Sending pduLevel Csnp PDU fails 1099 Tent New Distance from RootNodeSourceId 1101 LSP LevelType LSP level, which can be L1 or L2 1103 IP address took effect on the IS-IS interface Router B sent Csnp packets 1105 IS-IS Debugging Commands L3VPN Configuration Commands on Ospf Configuration CommandsRelated commands Abr-summary Ospf area view Syntax area area-id Area Ospf viewAsbr-summary Undo area area-id Display ospf asbr-summary Authentication-modeSimple Specifies the simple authentication mode View Ospf area view Syntax default cost cost limit limit tag tag type type DefaultRelated commands ospf authentication-mode Bandwidth-reference Ospf view Related commands import-route Ospf view Default-cost Ospf area viewUndo default cost limit tag type Syntax default-cost cost Undo default-cost Default-route-advertise summary cost cost Default-route-advertise Ospf viewRelated commands stub Ospf area view, nssa Undo default-route-advertise Syntax description description Undo description Description OSPF/OSPF area viewDisplay ospf abr-asbr # Describe the Ospf area0 as bone area Display ospf asbr-summary Syntax display ospf process-id brief Related commands asbr-summaryDisplay ospf brief Examples # Display Ospf brief information Description on the fields of the display ospf brief command Mpls TE Syntax display ospf process-id cumulative Display ospf cumulative1117 Nssa Display ospf errorSyntax display ospf process-id error ASE/NSSA Description on the fields of the display ospf error command 1119 Display ospf interface 1121 Display ospf lsdbBDR Description on the fields of the display ospf lsdb command # Display Type2 LSA Network LSA information in the Lsdb 1123 Display ospf nexthopSyntax display ospf process-id nexthop LS ID Display ospf peer # Display brief Ospf neighbor information Description on the fields of the display ospf peer commandDisplay ospf peer statistics Syntax display ospf process-id peer statistics Display ospf request-queue Keep neighbor relationship Init Examples # Display Ospf request list information Display ospf retrans-queue1127 Display ospf routing Syntax display ospf process-id vlink Description on the fields of the display ospf vlink commandDisplay ospf vlink 1129 Error Enables error logging Enable link-local-signalingEnable log State Enables state logging Filter import/export Enable out-of-band-resynchronization1131 Filter-policy export Ospf view By default, Summary LSAs filtering is disabledThis command is only available on an ABR Undo filter-policy export protocol process-id Graceful-restart Ospf view Examples # Filter redistributed routes using ACLFilter-policy import Ospf view 1133 Graceful-restart help Examples # Enable Ietf Graceful Restart for Ospf process# Enable non-IETF Graceful Restart for Ospf process Syntax graceful-restart help acl-numberprefix prefix-list Host-advertise Related commands ospf timer deadGraceful-restart interval Ospf view 1135 Import-route Ospf view Import-route command cannot redistribute default routes Related commands ExamplesDefault-route-advertise Ospf view 1137 Related commands lsa-generation-interval Lsa-arrival-interval Lsdb-overflow-limit Related commands lsa-arrival-intervalLsa-generation-interval Undo lsa-generation-interval Maximum-routes Maximum load-balancing Ospf viewNumber Maximum route number in the range 1 to Nssa Related commands ospfNetwork Ospf area view 1141 Examples # Configure area1 as an Nssa area Opaque-capability enableRelated commands default-cost Ospf area view Syntax opaque-capability enable Undo opaque-capability Undo ospf process-id Ospf authentication-modeOspf 1143 Related commands authentication-mode Syntax ospf cost value Undo ospf cost Ospf cost1145 Syntax ospf dr-priority priority Undo ospf dr-priority Ospf dr-priorityOspf mib-binding Syntax ospf mib-binding process-id Undo ospf mib-binding Ospf mtu-enable Ospf network-type This command is not supported on the Null interface Ospf timer deadRelated commands ospf dr-priority Syntax ospf timer dead seconds Undo ospf timer dead Syntax ospf timer hello seconds Undo ospf timer hello Ospf timer helloRelated commands ospf timer hello 1149 Ospf timer retransmit Ospf timer pollSyntax ospf timer poll seconds Undo ospf timer poll Peer Ospf trans-delaySyntax ospf trans-delay seconds Undo ospf trans-delay 1151 Examples # Specify the neighbor IP address Command sets priority for internal routesPreference Preference ase route-policy route-policy-name value Syntax reset ospf process-id process Reset ospf countersReset ospf process 1153 Rfc1583 compatible Reset ospf redistributionSyntax reset ospf process-id redistribution Syntax rfc1583 compatible Undo rfc1583 compatible Snmp-agent trap enable ospf Silent-interface Ospf view Ospf Configuration Commands Undo spf-schedule-interval Spf-schedule-intervalStub Ospf area view Syntax stub no-summary Undo stub Stub-router Default-cost Ospf area viewStub-router Undo stub-router Vlink-peer Ospf area view Examples # Enable a stub-router1159 Related commands authentication-mode,display ospf peer Syntax default cost value Undo default cost RIP Configuration CommandsDefault cost RIP view Checkzero # Disable default route sending Default-route originateRelated commands import-route RIP view Display rip Description on the fields of the display rip command 1163 Syntax display rip process-iddatabase Description on fields of the display rip database commandDisplay rip database X.X/X Display rip route Display rip interface1165 RIP Configuration Commands # Display the routing statistics of RIP process Description on the fields of the display rip route commandFilter-policy export RIP view 1167 Interface-type interface-number Specifies an interface Filter-policy import RIP viewExamples # Reference ACL 2000 to filter outbound routes Syntax host-route Undo host-route Host-route1169 Import-route RIP view Default cost RIP viewIncluding bgp , direct , isis , ospf , rip , rip and static Maximum load-balancing RIP view # Set the default cost for redistributed routes to1171 Syntax peer ip-address Rip Reset rip statisticsSyntax reset rip process-idstatistics 1173 Rip authentication-mode Undo rip authentication-mode # Enable Ethernet1/0 to receive RIP messages Mode and parametersBy default, an interface is enabled to receive RIP messages Format defined in RFC Rip metricin Related commands rip metricoutRelated commands rip metricin Rip metricout Syntax rip mib-binding process-id Undo rip mib-binding Rip mib-bindingRip output Syntax rip output Undo rip output Rip poison-reverse Related commands rip inputRip split-horizon Rip summary-address Examples # Enable the split horizon function on Ethernet1/0Related commands summary Rip triggered Rip version 1 2 broadcast multicast Rip versionUndo rip triggered Undo rip version Messages Silent-interface RIP viewAll Silents all interfaces 1181 Summary TimersRelated commands rip version Syntax summary Trip retransmit count 1183 Trip retransmit timer retransmit-time-value Trip retransmit timerUndo trip retransmit timer Syntax validate-source-address Undo validate-source-address Validate-source-addressVersion Version 1 Sysname system-view Sysname rip Sysname-rip-100 version Apply comm-list delete Routing Policy Common Configuration CommandsApply as-path Syntax apply comm-list comm-list-numberdelete Apply community Undo apply comm-list View Routing policy view Apply costSyntax apply cost + value Undo apply cost Parameters + Increases cost value. + Decreases cost value Apply cost-type Apply extcommunity Apply isis level-1 level-1-2 level-2 Undo apply isis No level is set by defaultApply isis 1191 Apply mpls-label Related commands route-policyApply local-preference Syntax apply mpls-label Undo apply mpls-label Syntax apply preference preference Undo apply preference Apply originApply preference 1193 Apply tag Apply preferred-valueSyntax apply tag value Undo apply tag Examples # Display the information of BGP AS path ACL Display ip as-pathSyntax display ip as-path as-path-acl number 1195 Display ip extcommunity-list Display ip community-listSyntax display ip extcommunity-list ext-comm-list-number Syntax display route-policy route-policy-name Display route-policyIf-match as-path Examples # Display the information of routing policy Related commands route-policyand ip community-list Related commands route-policy,ip as-pathaclIf-match community Syntax if-match cost value Undo if-match cost If-match costIf-match extcommunity 1199 If-match interface If-match mpls-label If-match route-type Syntax if-match tag value Undo if-match tag If-match tagIp as-path Undo ip as-path as-path-number Ip community-list 1203 Sysname system-view Sysname ip community-list 100 permit Undo ip extcommunity-list ext-comm-list-number Ip extcommunity-listRoute-policy 1205 Routing Policy Common Configuration Commands Display ip ip-prefix IPV4 Routing Policy Configuration CommandsSyntax display ip ip-prefix ip-prefix-name Related commands ip ip-prefix Examples # Display the statistics of IPv4 prefix list abc If-match ip Related commands Route-policy ExamplesIf-match ip-prefix Ip ip-prefix Syntax reset ip ip-prefix ip-prefix-name Reset ip ip-prefix1211 IPV4 Routing Policy Configuration Commands Display ip ipv6-prefix IPV6 Routing Policy Configuration CommandsApply ipv6 next-hop Syntax display ip ipv6-prefix ipv6-prefix-name String of 1 to 19 characters If-match ipv6Next-hop Matches the next hop of IPv6 routing information Address based match criterion for IPv6 routes Ip ipv6-prefix 1215 Syntax reset ip ipv6-prefix ipv6-prefix-name Reset ip ipv6-prefixExamples # Clear the statistics of IPv6 prefix list abc Ip route-static Static Routing Configuration CommandsDelete static-routes all Examples # Delete all static routes on the router Configured gateway-address Associate it with a Track entry Must be identical to that configured in the NQA test groupEthernet interface and Vlan interface 1219 Ip route-static default-preference Examples # Set the default preference of static routes to Balance IPv6 address family view IPV6 BGP Configuration CommandsRelated commands display ipv6 routing-tableon Bestroute as-path-neglect IPv6 address family view Bestroute compare-med IPv6 address family view Bestroute med-confederation IPv6 address family view Compare-different-as-med IPv6 address family view 1223 Dampening IPv6 address family view Default med IPv6 address family view Default local-preferenceIPv6 address family view1225 Display bgp ipv6 group Default-route imported IPv6 address family viewSyntax display bgp ipv6 group ipv6-group-name Syntax display bgp ipv6 network Display bgp ipv6 network1227 Display bgp ipv6 paths Syntax display bgp ipv6 paths as-regular-expression 1229 Display bgp ipv6 peerIncomplete Display bgp ipv6 routing-table Field Description Local router ID Display bgp ipv6 routing-table as-path-acl 1231 Display bgp ipv6 routing-table community Examples # Display routes filtered through the AS path ACL Syntax display bgp ipv6 routing-table dampened Display bgp ipv6 routing-table community-listDisplay bgp ipv6 routing-table dampened Examples # Display IPv6 BGP dampened routes Syntax display bgp ipv6 routing-table dampening parameter Display bgp ipv6 routing-table dampening parameterDisplay bgp ipv6 routing-table different-origin-as Syntax display bgp ipv6 routing-table different-origin-as Examples # Display IPv6 BGP route flap statistics Display bgp ipv6 routing-table flap-infoExamples # Display IPv6 BGP routes from different ASs 1235 Syntax display bgp ipv6 routing-table label CommandDisplay bgp ipv6 routing-table label Examples # Display IPv6 BGP label routing information Display bgp ipv6 routing-table regular-expression Display bgp ipv6 routing-table peer1237 Parameters as-regular-expression AS regular expression Display bgp ipv6 routing-table statisticFilter-policy exportIPv6 address family view Syntax display bgp ipv6 routing-table statistic Filter-policy import IPv6 address family view 1239 Examples # Reference ACL6 2001 to filter all inbound routes Group IPv6 address family viewImport-route IPv6 address family view Syntax group ipv6-group-name internal external Syntax ipv6-family Undo ipv6-family Ipv6-familyNetwork IPv6 address family view 1241 Peer advertise-community IPv6 address family view Peer allow-as-loop IPv6 address family view Peer advertise-ext-community IPv6 address family view1243 Peer as-number IPv6 address family view Import export Peer as-path-acl IPv6 address family view1245 Peer connect-interface IPv6 address family view Peer description IPv6 address family view Peer default-route-advertise1247 Peer ebgp-max-hop IPv6 address family view Peer fake-as IPv6 address family view Peer enable IPv6 address family view1249 Peer filter-policy IPv6 address family view Peer ignore IPv6 address family view Peer group IPv6 address family view1251 Peer ipv6-prefix Peer label-route-capability IPv6 address family view Peer keep-all-routes IPv6 address family view1253 Peer log-change IPv6 address family view Peer next-hop-local IPv6 address family view Peer preferred-value IPv6 address family view 1255 Peer public-as-only IPv6 address family view Peer reflect-client IPv6 address family view Peer route-limit IPv6 address family view 1257 Peer route-update-interval IPv6 address family view Peer route-policy IPv6 address family view Peer substitute-as IPv6 address family view Undo peer ipv6-group-nameipv6-address route-update-interval1259 Related commands timer IPv6 address family view Peer timer IPv6 address family viewPreference IPv6 address family view Reflect between-clients IPv6 address family view 1261 Reflector cluster-id IPv6 address family view Examples # Enable route reflection between clientsRefresh bgp ipv6 Reset bgp ipv6 1263 Reset bgp ipv6 dampening Reset bgp ipv6 flap-info Synchronization IPv6 address family view 1265 Timer IPv6 address family view Related commands peer timer IPv6 address family view 1267 IPV6 BGP Configuration Commands IPV6 IS-IS Configuration Commands # Display detailed IPv6 IS-IS routing information Ipv6 default-route-advertise 1271 Ipv6 filter-policy export Ipv6 enableSyntax ipv6 enable Undo ipv6 enable Undo ipv6 filter-policy export protocol process-id Undo ipv6 filter-policy import Related commands ipv6 filter-policy importIpv6 filter-policy import 1273 Related commands ipv6 filter-policy export Ipv6 import-route Undo ipv6 import-route isisv6 level-2 into level-1 Ipv6 import-route isisv6 level-2 into level-11275 Ipv6 maximum load-balancing Ipv6 preference Ipv6 summary 1277 Examples # Configure a summary route of 2002/32 Isis ipv6 enableSyntax isis ipv6 enable process-id Undo isis ipv6 enable Abr-summary OSPFv3 area view IPV6 OSPFV3 Configuration CommandsArea OSPFv3 view Syntax default-cost value Default costDefault-cost OSPFv3 area view Examples # Enter OSPFv3 Area 0 view Display debugging ospfv3 Related commands stubOSPFv3 area viewDisplay debugging ospfv3 Debugging state information Display ospfv3 Description on the fields of the display isofv3 commandSyntax display ospfv3 process-id Display ospfv3 interface 1283 Display ospfv3 lsdb # Display Link-local LSA information in the Lsdb 1285 Display ospfv3 lsdb statistic Syntax display ospfv3 lsdb statistic Syntax display ospfv3 process-id next-hop Display ospfv3 next-hopDisplay ospfv3 peer Interface-type interface-number interface type and number Description on the fields of the display isofv3 peer command Syntax display ospfv3 peer statistic Display ospfv3 peer statisticDisplay ospfv3 request-list Syntax display ospfv3 process-id request-list statistics Syntax display ospfv3 process-id retrans-list statistics Display ospfv3 retrans-list# Display the statistics of OSPFv3 link state request list LS-ID Display ospfv3 routing 1291 # Display the statistics of OSPFv3 routing table Syntax display ospfv3 statistic Display ospfv3 statisticDisplay ospfv3 topology Syntax display ospfv3 process-id topology area area-id Display ospfv3 vlink Syntax display ospfv3 process-id vlink Filter-policy exportOSPFv3 view 1295 Filter-policy importOSPFv3 view Routes that fail to pass are not added to the routing table Direct static Import-routeOSPFv3 viewAllow-ibgp direct static cost value type type route-policy Both Ebgp and Ibgp routes Maximum load-balancingOSPFv3 view Process Ospfv3 area Related commands router-idOspfv3 Undo ospfv3 process-id Ospfv3 cost Ospfv3 dr-priority Ospfv3 mtu-ignore Ospfv3 timer dead1301 Ospfv3 timer hello Related commands ospfv3 timer hello Related commands ospfv3 timer dead Ospfv3 timer retransmitOspfv3 trans-delay 1303 Preference ase route-policy route-policy-name preference Router-id router-id Related commands Ospfv3Silent-interfaceOSPFv3 view OSPFv3 processes on a router Spf timers Undo spf timers Undo vlink-peer router-id hello retransmit trans-delay dead Related commands default costExamples # Configure OSPFv3 area 1 as a stub area StubOSPFv3 area view IPV6 OSPFV3 Configuration Commands Syntax default cost cost Undo default cost IPV6 Ripng Configuration CommandsDefault cost RIPng view View RIPng view Display ripng Related commands import-routeSyntax display ripng process-id Display ripng database Description on the fields of the display ripng commandDescription on fields of the display ripng database command Syntax display ripng process-iddatabase Display ripng interface Syntax display ripng process-idroute Display ripng route1313 Filter-policy export Filter-policy import RIPng view Import-route 1315 Related commands default cost on Maximum load-balancing RIPng view Ripng # Restore the default RIPng route priority# Disable RIPng process Undo ripng process-id Ripng enable Ripng default-routeSyntax ripng process-idenable Undo ripng enable Ripng metricout Related commands ripng metricoutRipng metricin Syntax ripng metricin value Undo ripng metricin Ripng split-horizon Related commands ripng metricinRipng poison-reverse Syntax ripng poison-reverse Undo ripng poison-reverse Ripng summary-address Information, refer to Frame Relay Configuration Commands onLapb and X.25 Configuration Commands on Poison reverse function takes effect Timers 1323 IPV6 Ripng Configuration Commands Ipv6 route-static IPV6 Static Routing Configuration CommandsDelete ipv6 static-routes all Delete ipv6 static-routes all Sysname system-view Sysname ipv6 route-static 112 24 Related command multicast boundary Multicast Routing Forwarding Configuration CommandsDisplay multicast boundary Display multicast forwarding-table MID Major values of the flags field1329 Value Meaning Related command multicast minimum-ttl Display multicast minimum-ttl Display multicast routing-table Related command display multicast forwarding-table1331 Display multicast routing-table static Description on the fields of display multicast routing-table Display multicast rpf-info 1333 Ip rpf-route-static 1335 Related command display multicast routing-table static Mtracert Multicast boundary Description on the fields of the mtracert command1337 Related command display multicast boundary Multicast forwarding-table downstream-limit Multicast forwarding-table route-limit 1339 Syntax multicast longest-match Undo multicast longest-match Multicast load-splittingMulticast longest-match View System view, VPN instance view Multicast minimum-ttl Multicast routing-enableRelated command display multicast minimum-ttl 1341 Reset multicast forwarding-table # Enable IP multicast routing in VPN instance mvpn Reset multicast routing-table 1343 Sysname reset multicast routing-table Igmp Configuration Commands Display igmp group Description on the fields of the display igmp group command Display igmp interface 1347 Display igmp routing-table Igmp Related command igmp fast-leave,last-member-query-intervalFast-leave Igmp view Syntax fast-leave group-policy acl-number Undo fast-leave Syntax igmp enable Undo igmp enable Igmp enableRelated command igmp enable, and multicast routing-enableon Related command igmp Undo igmp group-policy Igmp fast-leaveIgmp group-policy 1351 Igmp last-member-query-interval By default, the last-member query interval is 1 secondIgmp max-response-time Igmp require-router-alert 1353 Igmp send-router-alert Robust-count Igmp view , igmp timer query , igmpIgmp robust-count Igmp interface Igmp static-group Igmp timer other-querier-present Igmp timer query Last-member-query-interval Related command version Igmp viewIgmp version Undo igmp version Require-router-alert Igmp view Max-response-time Igmp viewSyntax require-router-alert View Public instance Igmp view, VPN instance Igmp view Reset igmp groupUndo require-router-alert 1359 Robust-count Igmp view Related command display igmp groupSyntax robust-count robust-value Undo robust-count Syntax send-router-alert Undo send-router-alert Timer other-querier-present Igmp viewSend-router-alert Igmp view 1361 Syntax timer query interval Undo timer query Timer query Igmp viewPublic instance Version Igmp view Related command igmp version1363 Igmp Configuration Commands Display msdp brief Msdp Configuration CommandsCache-sa-enable Characters Display msdp peer-status 1367 Display msdp sa-cache Related command cache-sa-enable 1369 Display msdp sa-count Import-source Encap-data-enableSyntax encap-data-enable Undo encap-data-enable View Public instance Msdp view, VPN instance Msdp view Related command display multicast routing-tableon Related command peer sa-policyMsdp Undo originating-rp Originating-rpPeer connect-interface 1373 Peer description Related command static-rpf-peerRelated command display msdp peer-status Peer mesh-group Undo peer peer-addressminimum-ttl Peer minimum-ttlUndo peer peer-addressmesh-group 1375 Peer request-sa-enable Peer sa-cache-maximum From the Msdp peer Import-source commandPeer sa-policy Display msdp peer-status and import-source Reset msdp peer Peer sa-request-policy Related command cache-sa-enableand display msdp sa-cache Reset msdp sa-cache1379 Shutdown Msdp View Reset msdp statisticsUndo shutdown peer-address Static-rpf-peer Related command display msdp peer-statusand ip prefix-listExample # Configure static RPF peers in the public instance Undo static-rpf-peer peer-address Timer retry Syntax timer retry interval Undo timer retry Related command static-rp PIM view PIM Configuration CommandsAuto-rp enable Bsr-policy PIM view Bsr PIM view Undo c-bsr Bsr global Bsr admin-scopeSyntax c-bsr admin-scope Undo c-bsr admin-scope 1385 Bsr group Undo c-bsr group group-address Syntax c-bsr hash-length hash-length Undo c-bsr hash-length Bsr hash-length PIM viewBsr holdtime PIM view Syntax c-bsr holdtime interval Undo c-bsr holdtime Bsr priority PIM view Related command c-bsr PIM view and c-bsr interval PIM viewBsr interval PIM view Bsr PIM view and c-bsr holdtime PIM view Rp PIM view 1389 Rp advertisement-interval interval Related command c-bsr PIM viewRp advertisement-interval PIM view Undo c-rp advertisement-interval Crp-policy PIM view Related command c-rp PIM view and c-bsr interval PIM viewRp holdtime PIM view Syntax c-rp holdtime interval Undo c-rp holdtime Related command c-bsr PIM view and c-rp PIM view Display pim bsr-info Display pim claimed-route 1393 Display pim control-message counters 1395 BSR Display pim grafts Description on the fields of the display pim grafts commandDisplay pim interface 1397 Display pim join-prune PIM DR Display pim neighbor 1399 Interface connecting the PIM neighbor Display pim routing-table 1401 Sysname display pim routing-table Vpn-instance public net Display pim rp-info 1403 Description on the fields of the display pim rp-info command Hello-option holdtime PIM view Related command pim hello-optiondr-priorityHello-option dr-priority PIM view 1405 Related command pim hello-option holdtime Hello-option lan-delay PIM viewThis command is effective for both PIM-DM and PIM-SM Hello-option neighbor-tracking PIM view Hello-option override-interval PIM view Related command pim hello-optionneighbor-tracking1407 Holdtime join-prune PIM view Holdtime assert PIM viewSyntax holdtime assert interval Undo holdtime assert Jp-queue-size PIM view Related command jp-queue-size PIM viewJp-pkt-size PIM view Syntax jp-pkt-size packet-size Undo jp-pkt-size Pim Related command multicast routing-enableonUndo pim vpn-instance vpn-instance-name Pim dm Pim bsr-boundaryBsr PIM view , and multicast boundary on Related command hello-optiondr-priority PIM view Related command pim sm, ssm-policy PIM viewExample # Enable PIM-DM on Ethernet 1/0 Pim hello-option dr-priority Pim hello-option holdtime Pim hello-option lan-delayRelated command hello-option holdtime PIM view 1413 Pim hello-option neighbor-tracking Pim hello-option override-interval Pim holdtime join-prune Pim holdtime assert1415 Pim sm Pim require-genidView Interface view Parameter None Example # Enable PIM-SM on Ethernet 1/0 Pim timer graft-retryRelated command pim dm Example # Disable state refresh on Ethernet 1/0 Syntax pim timer hello interval Undo pim timer hello Pim timer helloPim timer join-prune Related command timer hello PIM view Probe-interval PIM view Pim triggered-hello-delayRelated command timer join-prune PIM view Syntax probe-interval interval Undo probe-interval Syntax register-suppression-timeout interval Register-suppression-timeout PIM viewRelated command register-suppression-timeout PIM view Register-policy PIM view Syntax register-whole-checksum Undo register-whole-checksum Undo register-suppression-timeoutRegister-whole-checksum PIM view 1421 Source-lifetime PIM view Reset pim control-message countersRelated command state-refresh-interval PIM view Syntax source-lifetime interval Undo source-lifetime Source-policy PIM view Spt-switch-threshold PIM viewUndo spt-switch-threshold group-policy acl-number Syntax source-policy acl-number Undo source-policy PIM Configuration Commands Syntax ssm-policy acl-number Undo ssm-policy Ssm-policy PIM viewState-refresh-interval PIM view 1425 State-refresh-ttl PIM view State-refresh-rate-limit PIM viewSyntax state-refresh-ttl ttl-value Undo state-refresh-ttl Undo static-rp rp-address By default, the TTL value of state refresh messages isStatic-rp PIM view 1427 Related command display pim rp-infoand auto-rp enable Timer hello PIM viewTimer join-prune PIM view Related command pim timer hello Syntax timer spt-switch interval Undo timer spt-switch Timer spt-switch PIM viewRelated command pim timer join-prune Related command spt-switch-threshold PIM view PIM Configuration Commands Display multicast ipv6 boundary IPV6 Multicast Routing Forwarding Configuration CommandsRelated command multicast ipv6 boundary Display multicast ipv6 forwarding-table IPV6 Multicast Routing and Forwarding Configuration Commands Values and meanings of the Flags field Display multicast ipv6 minimum-hoplimit1433 Related command multicast ipv6 minimum-hoplimit Display multicast ipv6 routing-table Display multicast ipv6 rpf-info Related command display multicast ipv6 forwarding-table1435 Multicast ipv6 boundary Multicast ipv6 forwarding-table downstream-limit Related command display multicast ipv6 boundary1437 Multicast ipv6 forwarding-table route-limit Multicast ipv6 load-splitting Multicast ipv6 minimum-hoplimit Multicast ipv6 longest-match1439 Multicast ipv6 routing-enable Related command display multicast ipv6 minimum-hoplimit Reset multicast IPv6 routing-table Reset multicast ipv6 forwarding-table1441 Sysname reset multicast ipv6 routing-table ff03101 MLD Configuration Commands Display mld group Display mld interface Description on the fields of the display mld group commandInformation of all interfaces running MLD Display mld routing-table 1445 Fast-leave MLD view Syntax fast-leave group-policy acl6-number Undo fast-leave Syntax max-response-time interval Undo max-response-time Last-listener-query-intervalMax-response-time MLD view 1447 Mld Mld enableSyntax mld enable Undo mld enable Syntax mld Mld fast-leave Related command mldExample # Enable MLD on Ethernet 1/0 Mld group-policy Mld last-listener-query-interval Mld require-router-alert Mld max-response-time1451 Mld robust-count Syntax mld robust-count robust-value Undo mld robust-count Mld send-router-alert Mld send-router-alertMld static-group Undo mld send-router-alert Undo mld timer other-querier-present Mld timer other-querier-presentMld timer other-querier-present interval 125 x 2 + 10 / 2 = 255 seconds Related command mld version Mld timer querySyntax mld timer query interval Undo mld timer query Mld version Require-router-alert Reset mld groupRequire-router-alert MLD view Mld require-router-alert and send-router-alert MLD view # Clear all MLD forwarding entries on Ethernet 1/0 Related command display mld groupRobust-count MLD view 1457 Send-router-alert MLD view Timer other-querier-present MLD viewBy default, the MLD querier robustness variable is View MLD view Related command Timer query MLD viewTimer query interval Version MLD view Example # Globally set the MLD version to MLDv2 Bsr IPv6 PIM view IPV6 PIM Configuration CommandsBsr-policy IPv6 PIM view Syntax bsr-policy acl6-number Undo bsr-policy Related command c-bsr IPv6 PIM view on Bsr hash-length IPv6 PIM view Bsr interval IPv6 PIM view Example # Set the bootstrap timeout time to 150 secondsBsr holdtime IPv6 PIM view Syntax c-bsr interval interval Undo c-bsr interval Rp IPv6 PIM view Related command c-bsr IPv6 PIM viewBsr priority IPv6 PIM view Bsr IPv6 PIM view and c-bsr holdtime IPv6 PIM view View IPv6 PIM view Rp advertisement-interval IPv6 PIM view1465 Rp holdtime IPv6 PIM view Related command c-rp IPv6 PIM viewExample # Set the global C-RP timeout time to 200 seconds Example # Set the global C-RP-Adv interval to 30 seconds Display pim ipv6 bsr-info Related command c-bsr IPv6 PIM view and c-rp IPv6 PIM viewCrp-policy IPv6 PIM view Syntax crp-policy acl6-number Undo crp-policy Display pim ipv6 claimed-route Syntax display pim ipv6 claimed-route ipv6-source-address Display pim ipv6 control-message counters BSR Display pim ipv6 grafts Display pim ipv6 graftsDisplay pim ipv6 interface Unacknowledged graft messages Interface PIM version PIM mode To send on the specified interface Display pim ipv6 join-prunePIM-SM and IPv6 PIM-SSM respectively Specified IPv6 PIM neighbor Display pim ipv6 neighbor Display pim ipv6 routing-table 1475 Related command display multicast ipv6 routing-tableon Example # View the content of the IPv6 PIM routing table Syntax display pim ipv6 rp-info ipv6-group-address Display pim ipv6 rp-info1477 Embedded-rp Syntax embedded-rp acl6-number Undo embedded-rp acl6-number Hello-option holdtime IPv6 PIM view Related command pim ipv6 hello-optiondr-priorityHello-option dr-priority IPv6 PIM view Example # Set the router priority for DR election to Example # Set the prune delay to 200 milliseconds globally Hello-option lan-delay IPv6 PIM viewRelated command pim ipv6 hello-option holdtime Hello-option neighbor-tracking IPv6 PIM view Hello-option override-interval IPv6 PIM view Related command pim ipv6 hello-optionneighbor-trackingExample # Disable join suppression globally Holdtime assert IPv6 PIM view Holdtime join-prune IPv6 PIM view Jp-queue-size IPv6 PIM view Related command jp-queue-size IPv6 PIM viewJp-pkt-size IPv6 PIM view 1483 Pim ipv6 bsr-boundary Related command multicast ipv6 routing-enableonPim ipv6 Syntax pim ipv6 Undo pim ipv6 Pim ipv6 dm Related commands pim ipv6 sm, ssm-policy IPv6 PIM viewExample # Enable IPv6 PIM-DM on Ethernet 1/0 Syntax pim ipv6 dm Undo pim ipv6 dm Pim ipv6 hello-option dr-priority Related command hello-optiondr-priority IPv6 PIM viewRelated command hello-option holdtime IPv6 PIM view Pim ipv6 hello-option holdtime Pim ipv6 hello-option neighbor-tracking Pim ipv6 hello-option lan-delay1487 Pim ipv6 hello-option override-interval Related command hello-optionneighbor-tracking IPv6 PIM viewExample # Disable join suppression on Ethernet 1/0 Pim ipv6 holdtime assert Syntax pim ipv6 require-genid Undo pim ipv6 require-genid Pim ipv6 holdtime join-prunePim ipv6 require-genid 1489 Pim ipv6 sm Pim ipv6 smPim ipv6 state-refresh-capable Undo pim ipv6 sm Pim ipv6 timer hello Pim ipv6 timer graft-retry1491 Related command timer hello IPv6 PIM view Pim ipv6 timer join-prunePim ipv6 triggered-hello-delay Related command timer join-prune IPv6 PIM view Register-policy IPv6 PIM view Related command register-suppression-timeout IPv6 PIM viewProbe-interval IPv6 PIM view Example # Set the probe time to 6 seconds Register-suppression-timeout IPv6 PIM view Register-whole-checksum IPv6 PIM view Reset pim ipv6 control-message counters1495 Source-policy IPv6 PIM view Related command state-refresh-interval IPv6 PIM viewSource-lifetime IPv6 PIM view Syntax source-policy acl6-number Undo source-policy Undo spt-switch-threshold group-policy acl6-number Spt-switch-threshold IPv6 PIM view1497 Ssm-policy IPv6 PIM view Syntax ssm-policy acl6-number Undo ssm-policy State-refresh-interval IPv6 PIM view State-refresh-hoplimit1499 Static-rp IPv6 PIM view State-refresh-rate-limit IPv6 PIM viewExample # Set the state refresh interval to 70 seconds Undo static-rp ipv6-rp-address Timer hello IPv6 PIM viewRelated command display pim ipv6 rp-info 1501 Related command pim ipv6 timer hello Timer join-prune IPv6 PIM viewTimer spt-switch IPv6 PIM view Related command pim ipv6 timer join-prune Related command spt-switch-threshold IPv6 PIM view 1503 IPV6 PIM Configuration Commands Display multicast-domain vpn-instance switch-group receive Multicast VPN Configuration CommandsDisplay multicast-domain vpn-instance share-group Count Display multicast-domain vpn-instance switch-group send 1507 Multicast-domain holddown-time View VPN instance view Multicast-domain log switch-group-reuseMulticast-domain share-group 1509 Multicast-domain switch-delay Undo multicast-domain switch-group-pool Multicast-domain switch-group-pool1511 Sysname system-view Sysname ip vpn-instance mvpn Display mpls fast-forwarding cache Mpls Basics Configuration CommandsDisplay mpls fast-forwarding cache verbose Syntax display mpls ilm label include text Display mpls ilm# Display all ILM entries Display mpls interface Related command display mpls statistics interface1515 Display mpls label Display mpls label label-value1 to label-value2 all Display mpls ldp all verbose begin exclude include Display mpls ldpMpls ldp system view , mpls ldp interface view Display mpls ldp cr-lsp Description on the fields of the display mpls ldp commandLSR ID All Displays all information Related command display mpls lspDisplay mpls ldp interface 1519 Example # Display information about all LDP interfaces # Display detailed information about all interfaces Dest-addr Destination address of the LSP Display mpls ldp IspAll Displays information about all LSPs established by LDP Established by LDP Related command display mpls ldp Display mpls ldp peer # Display detailed information about all peers Example # Display information about all peers1523 Display mpls ldp remote-peer Example # Display information about remote peer BJI Display mpls ldp session 1525 LAM Example # Display information about sessions# Display detailed information about all sessions MD5 Display mpls ldp vpn-instance 1527 Incoming-interface Incoming interface of the LSPs Display mpls lspExample # Display information about VPN instance vpn1 Outgoing-interface Outgoing interface of the LSPs Dest-addr Destination address Exclude Excludes the specified FECInclude Includes the specified FEC Asbr Displays information about Asbr established LSPs # Display detailed information about all LSPs Description on the fields of the display mpls lsp commandExample # Display information about all LSPs FEC Syntax display mpls lsp statistics Display mpls lsp statisticsDisplay mpls nhlfe Syntax display mpls nhlfe token include text Display mpls route-state # Display all Nhlfe entries Display mpls static-lsp 1533 Example # Display brief information about static LSPs Display mpls statistics interface# Display detailed information about static LSPs Example # Display Mpls statistics for all interfaces Related command statistics interval1535 Display mpls statistics lsp Syntax display mpls statistics lsp index all name lsp-name Example # Display Mpls statistics for all LSPs 1537 Du-readvertise Du-readvertise timerSyntax du-readvertise timer value Undo du-readvertise timer Are both View Mpls LDP view Graceful-restart Mpls LDP viewGraceful-restart mpls ldp Syntax graceful-restart mpls ldp Related commands graceful-restart Mpls LDP view Graceful-restart timer neighbor-livenessGraceful-restart timer reconnect Syntax graceful-restart timer reconnect timer Undo graceful-restart timer reconnect Graceful-restart timer recovery1541 Label advertise Related command loop-detect,path-vectorsHops-count Syntax hops-count hop-number Undo hops-count Label-distribution independent ordered Label-distributionUndo label advertise Undo label-distribution Label-retention conservative liberal Label-retentionUndo label-retention Loop-detect Related command hops-count,path-vectorsUse the undo lsp-trigger command to restore the default Lsp-trigger Syntax lsr-idlsr-id # Configure the LDP LSR ID of LDP instance named vpn1Lsr-id Undo lsr-id Syntax mpls Md5-passwordMpls Undo mpls Mpls ldp system view Related command mpls lsr-id# Enable Mpls for interface Ethernet 1/0 View System view/interface view Syntax mpls ldp Undo mpls ldp # Enable LDP for VPN instance vpn1Mpls ldp interface view 1549 Mpls ldp advertisement dod du Mpls ldp advertisementUndo mpls ldp advertisement Mpls ldp remote-peer Mpls ldp timer hello-holdRelated command remote-ip Example # Create a remote peer entity named BJI Mpls ldp timer keepalive-hold View Interface view/MPLS LDP remote peer view Mpls ldp transport-addressMpls lsr-id Syntax mpls lsr-id lsr-id Undo mpls lsr-id Syntax mtu-signalling Undo mtu-signalling Mtu-signallingRelated command display mpls interface Example # Set the LSR ID to Ping lsp Related command loop-detect,hops-countPath-vectors Syntax path-vectors pv-number Undo path-vectors Remote-ip Syntax remote-ip ip-address Undo remote-ip Related command mpls ldp remote-peer Reset mpls fast-forwarding cacheReset mpls ldp Reset mpls fast-forwarding cache Reset mpls statistics lsp Reset mpls statistics interfaceSyntax reset mpls statistics lsp index all name lsp-name Static-lsp egress Snmp-agent trap enable mplsRelated command display mpls statistics lsp Lsp-name Name for the LSP, a string of 1 to 15 characters Static-lsp ingress Undo static-lsp ingress lsp-name Undo static-lsp transit lsp-name Static-lsp transit1561 Tracert lsp Related command static-lsp egress, static-lsp ingressStatistics interval Syntax tracert lsp -a source-ip-exp Ttl expiration pop Ttl expiration pop commandTtl expiration Undo ttl expiration pop Ttl propagate Mpls TE Configuration Commands Add hop Syntax delete hop ip-address Delete hopDisplay explicit-path Syntax display explicit-path pathname # Display the latest TE information advertised by IS-IS TE Display isis traffic-eng advertisements1567 Intf Addr Verbose Displays details Display isis traffic-eng link1569 Display isis traffic-eng network Vpn-instance vpn-instance-name Specifies a VPN instance. Display isis traffic-eng statistics 1571 Related command te-set-subtlv Display isis traffic-eng sub-tlvs Display mpls rsvp-te Label switched Router ID, About RSVP-TE globally or for an interface Display mpls rsvp-te establishedBegin include exclude regular-expression # Display RSVP-TE information for interface Ethernet 1/0 Filters output by regular expression Display mpls rsvp-te peerSpaces Display mpls rsvp-te psb-content 1577 Erhopstrict 1579 Display mpls rsvp-te requestRSVP-TE requests on the specified or all interfaces X.X Display mpls rsvp-te reservation 1581 Display mpls rsvp-te rsb-contentLSP ID Tunnel Dest Display mpls rsvp-te sender 1583 Interface is specified Display mpls rsvp-te statisticsGlobal Display global RSVP-TE information RSVP-TE is displayed # Display the RSVP-TE statistics of interface Serial 1/0 1585 Display mpls static-cr-lsp Ip-address prefix-length arguments # Display detailed information about all static CR-LSPs Display mpls te cspf tedb1587 IGP 1589 # Display the Tedb information of IGP area# Display all Tedb information Mpls LSR ID IGP # Display the Tedb information of all nodes # Display Tedb information for a specified interface address Display mpls te link-administration admission-control Links of all interfaces if no interface is specified Description on fields of the command Display mpls te link-administration bandwidth-allocation1593 Display mpls te tunnel Egress ingress remote transit name name incoming-interface 1595 # Display detailed information about Mpls TE tunnelsLSP-ID Lsr-id Ingress LSR ID, in dotted decimal notation Display mpls te tunnel path# Display the paths that all Mpls TE tunnels traverse Syntax display mpls te tunnel statistics Display mpls te tunnel statisticsDisplay mpls te tunnel-interface Syntax display mpls te tunnel-interface CR-LSP Display ospf mpls-te 1599 Area ID TE enabled Ospf area ID LSA Type Syntax display ospf process-id traffic-adjustment Display ospf traffic-adjustment1601 Syntax display tunnel-info tunnel-id all statistics Display tunnel-info# Display statistics about tunnels # Enable IGP shortcut when the IGP protocol is IS-IS Enable traffic-adjustmentEnable traffic-adjustment advertise View Ospf view/IS-IS view Explicit-path List hop View Explicit path view Modify hop1605 Undo mpls rsvp-te authentication Mpls rsvp-te authenticationMpls rsvp-te authentication cipher plain auth-key Mpls rsvp-te Mpls rsvp-te blockade-multiplier 1607 Mpls rsvp-te hello Related command mpls rsvp-te timer refreshMpls rsvp-te graceful-restart Syntax mpls rsvp-te hello Undo mpls rsvp-te hello Mpls rsvp-te hello-lost # Enable Rsvp hello extension on interface Ethernet 1/01609 Mpls rsvp-te reliability Related command mpls rsvp-te timer helloMpls rsvp-te keep-multiplier Example # Set the keep multiplier to five Mpls rsvp-te resvconfirm Mpls rsvp-te srefresh Mpls rsvp-te timer graceful-restart recovery Mpls rsvp-te timer graceful-restart restart Related command mpls rsvp-te hello, mpls rsvp-tehello-lost Mpls rsvp-te timer helloMpls rsvp-te timer refresh Example # Set the hello interval to five seconds Related command mpls rsvp-tekeep-multiplier Mpls rsvp-te timer retransmissionUndo mpls rsvp-te timer retransmission Syntax mpls te # Enable Mpls TE on interface Ethernet 1/0Mpls te Undo mpls te Mpls te auto-bandwidth Related command mpls te link administrative groupMpls te affinity property Undo mpls te auto-bandwidth Mpls te backup hot-standby ordinary Mpls te backupRelated command mpls te timer auto-bandwidth Undo mpls te backup With backup enabled, the record route Mpls te backup bandwidthExample # Enable hot backup on tunnel Mpls te bandwidth bc0 bc1 bandwidth Mpls te bandwidthMpls te bandwidth change thresholds Undo mpls te bandwidth Syntax mpls te commit Mpls te commitView Tunnel interface view Example # Set the failed link timer to 50 seconds Mpls te cspf timer failed-linkRelated command mpls te cspf Mpls te cspf Mpls te fast-reroute bypass-tunnel Mpls te fast-rerouteSyntax mpls te fast-reroute Undo mpls te fast-reroute # Set the hold time to 10000 milliseconds Mpls te igp advertiseDescription Example 1623 Mpls te igp shortcut isis ospf Mpls te igp metricMpls te igp shortcut Undo mpls te igp shortcut Mpls te loop-detection Mpls te link administrative groupRelated command mpls te affinity property Syntax mpls te loop-detection Undo mpls te loop-detection Mpls te max-link-bandwidth Mpls te max-reservable-bandwidth Undo mpls te max-reservable-bandwidth Related command mpls te path metric-typeMpls te metric Syntax mpls te metric value Undo mpls te metric Mpls te path metric-type Related command mpls te metricMpls te path explicit-path Example In Mpls view Undo mpls te priority Mpls te priorityMpls te record-route Syntax mpls te record-route label Undo mpls te record-route Mpls te reoptimization tunnel interface view Mpls te reoptimization user viewMpls te reoptimization Mpls te resv-style Mpls te retry Example # Enable route pinning Related command mpls te timer retryExample # Set the maximum number of tunnel setup retries to Mpls te route-pinning Mpls te tie-breaking Mpls te signal-protocolMpls te signal-protocol crldp rsvp-te static Mpls te tie-breaking least-fill most-fill random By default, automatic bandwidth adjustment is disabled Mpls te timer auto-bandwidthRelated command mpls te auto-bandwidth Syntax mpls te timer retry second Undo mpls te timer retry Mpls te timer fast-rerouteMpls te timer retry 1635 Mpls te tunnel-id Related command mpls te retryExamples # Configure the tunnel ID as Mpls te vpn-binding Related command opaque-capability Mpls-te enableSyntax mpls-te enable Undo mpls-te Next hop Related command delete hop Opaque-capability Syntax reset mpls te auto-bandwidth adjustment timers Reset mpls rsvp-te statisticsReset mpls te auto-bandwidth adjustment timers Static-cr-lsp egress Static-cr-lsp ingress CR-LSP on the ingress or a transit node Static-cr-lsp transitUndo static-cr-lsp transit tunnel-name Bw-constraint Sets the bandwidth constraint sub-TLV Use the undo te-set-subtlvcommand to restore the default# Configure sub-TLVs for IS-IS process Value Sub-TLV in the range 19 to If no level is specified, IS-IS TE applies to Level-1-2 Cost-style on Mpls TE Configuration Commands Mpls L2VPN Configuration Ccc interface in-label out-label Ccc interface out-interface Undo ce ce-name View Mpls L2VPN CE view Connection# Create a CE named ce2 for a VPN 1647 Display bgp l2vpn Related command route-distinguisher Mpls L2VPN viewTunnel select-seq load-balance-number on 1649 CE ID Verbose Peer Local 1651 Pref Preference # Display information about all local CCC connections Display cccSyntax display ccc ccc-name ccc-nametype local remote # Display information about all CCC connections Display l2vpn ccc-interface vc-type Down Display mpls l2vc Configured on the routerConfigured on the CE interface 1655 VC ID VC ID Display mpls l2vpn Vpn-name local-ce remote-ce # Display information about L2VPN vpn1 Description on the fields of the display mpls l2vpn command# Display information about local CEs of L2VPN vpn1 # Display information about remote CEs of L2VPN vpn1 Display mpls l2vpn connection1659 Status Status of the connection Peer-id Description on the fields of mpls l2vpn connection summary Display mpls static-l2vc Display mpls l2vpn forwarding-infoExample # Display Mpls L2VPN forwarding information Syntax l2vpn-family L2vpn-family1663 Mpls l2vc Related command tunnel select-seqload-balance-numberonUndo l2vpn-family Example # Create a Martini Mpls L2VPN connection Mpls l2vpnMpls l2vpn vpn-name Syntax mpls l2vpn Undo mpls l2vpn # Create Kompella VPN named vpn2 and enter Mpls L2VPN view Mpls static-l2vc destinationUndo mpls static-l2vc Syntax mtu mtu Reset bgp l2vpnMtu Mpls L2VPN view Example # Set the MTU for Kompella connections to Route-distinguisher Mpls L2VPN view Re-create the VPN using the new RDTakes effect only when it is configured with an RD Route-distinguisher route-distinguisher Example # Associate VPN vpn1 with VPN targets Vpn-target Mpls L2VPN view1669 Mpls L2VPN Configuration Commands Syntax default local-preference value Apply access-vpn vpn-instanceDefault local-preference BGP-VPNv4 subaddress family view View Policy routing view Default med BGP-VPNv4 subaddress family view Display bgp vpnv4 all routing-table Description VPN instance view1673 Example # Display all BGP VPNv4 routing information All Specifies all VPNv4 peers Display bgp vpnv4 group1675 Display bgp vpnv4 network Be displayed Display bgp vpnv4 pathsDisplay bgp vpnv4 all vpn-instance vpn-instance-name paths # Display all BGP VPNv4 AS path information Verbose Displays detailed information Display bgp vpnv4 peerVPNv4 peers 1679 # Display all BGP VPNv4 peer information # Display detailed information about BGP VPNv4 peer 1681 Display bgp vpnv4 route-distinguisher routing-table Example # Display the BGP VPNv4 routing information of RD Related command route-distinguisher VPN instance view1683 Fields of the above output All Specifies all VPNv4 peers Display bgp vpnv4 routing-table label1685 Display bgp vpnv4 vpn-instance routing-table 1687 Display fib statistics vpn-instance Display fib statistics vpn-instanceDisplay fib vpn-instance Display fib vpn-instance vpn-instance-name include string # Display detailed information about a VPN instance Display ip vpn-instance1689 Syntax display ospf process-id sham-link area area-id Related command sham-linkDisplay ospf sham-link Example # Display information about all Ospf sham links Display tunnel-policy all policy-name tunnel-policy-name Display tunnel-policy# Display information about Ospf sham links in area Tunneling policy or all tunneling policies Domain-id Example # Configure the Ospf domain ID# Display tunneling policy aaa Filter-policy export BGP-VPNv4 subaddress family view Export route-policy1693 Filter-policy import BGP-VPNv4 subaddress family view Ip binding vpn-instance Import route-policy1695 View BGP view Ip vpn-instanceIpv4-family Vpnv4 Enters BGP-VPNv4 subaddress family view Peer advertise-community BGP-VPNv4 subaddress family view 1697 Peer allow-as-loop Peer as-path-acl BGP-VPNv4 subaddress family view Peer default-route-advertise vpn-instance 1699 Related command peer upe Peer enablePeer filter-policy BGP-VPNv4 subaddress family view Peer group 1701 Peer ip-prefix BGP-VPNv4 subaddress family view Peer label-route-capability BGP view/BGP VPN instance view Peer next-hop-invariable BGP-VPNv4 subaddress family view 1703 Peer next-hop-local Peer public-as-only BGP-VPNv4 subaddress family view Peer reflect-client 1705 Peer route-policy BGP-VPNv4 subaddress family view Peer upe Syntax policy vpn-target Undo policy vpn-target Command applies to inter-provider VPN option B schemesPolicy vpn-target 1707 Reflect between-clients Reflector culster-id Refresh bgp vpn-instance 1709 Reset bgp vpn-instance Refresh bgp vpnv4 Reset bgp vpn-instance flap-info Reset bgp vpn-instance dampening1711 Route-distinguisher VPN instance view Reset bgp vpnv4Syntax route-distinguisher route-distinguisher Instance Then re-create the VPN instance and re-configure a new RDRoute-tag Syntax route-tag tag-value Undo route-tag Routing-table limit Example # Configure the route tag for Ospf process 100 asImport-route Ospf view on Undo rr-filter Rr-filterSham-link View Ospf area view Mpls L3VPN Configuration Commands Tunnel-policy Related command tunnel select-seqload-balance-numberTnl-policy VPN instance view Undo tnl-policy Tunnel select-seq load-balance-number Load-balance-number command can be usedUndo tunnel select-seq View Ospf multi-instance view Vpn-instance-capability simpleVpn-target VPN instance view 1719 Mpls L3VPN Configuration Commands Authentication-method VAM Server Configuration CommandsAuthentication-algorithm Vam server vpn , authentication-method Vam server vpn , authentication-algorithm Display vam server address-map Description on the fields of display vam server address-map Display vam server statisticSyntax display vam server statistic all vpn vpn-name 1723 Example # Display statistics of the VAM server # Display statistics of VPN domain 1 on the VAM server Hub private-ip Related command vam server vpnEncryption-algorithm Undo hub private-ip private-ip-address Related command vam server vpn, keepalive retry Keepalive interval Pre-shared-key VPN domain view Related command vam server vpn, keepalive intervalKeepalive retry Syntax keepalive retry retry-times Undo keepalive retry Related command vam server vpn, vam server enable Server enableSyntax server enable Undo server enable Example # Enable the VAM server function of VPN domain Related command Vam server vpn, server enable Example Vam server enableVam server ip-address Vam server vpn Syntax vam server vpn vpn-name Undo vam server vpn vpn-name Related command vam client name, and vam client enable VAM Client Configuration CommandsClient enable 100 Example # Display the status information of VAM client abc VAM client view Pre-shared-key VAM client viewPre-shared-key cipher simple key-string Cipher Specifies a pre-shared key in cipher text Resend interval No pre-shared key is configured by defaultRelated command vam client name Syntax resend interval time-interval Undo resend interval Server secondary ip-address Server primary ip-address1735 Example # Set the local username and password both to user Vam client enableBy default, no local username or password is configured User Vam client name Vam client name and client enableBy default, no VAM client is configured An interface Undo vpn VpnExample # Specify the VAM client abc to belong to VPN 101 Ipsec Profile Configuration CommandsRelated command ipsec profile system view Display ipsec profile Inbound ESP setting Ipsec profile system view 1741 Ipsec Profile Configuration Commands Display dvpn session Dvpn Tunnel Configuration Commands102 Associated with the VAM client Dvpn session dumb-time Dumb Undo ipsec profile ipsec-profile-name&1-6 Dvpn session idle-timeIpsec profile tunnel interface view 1745 Keepalive Undo keepalive Tunnel-protocol dvpn udp Related command Interface tunnel on ExampleSyntax tunnel-protocol dvpn udp Undo tunnel-protocol Vam client Related command interface tunnel onExample # Configure the Dvpn tunnel mode Syntax vam client client-name Undo vam client Related command interface tunneland source GRE Configuration Commands103 Example # Display information about interface Tunnel0 Down 1751 Gre checksum Syntax gre checksum Undo gre checksum Undo gre key Related command interface tunnelGre key 1753 Syntax interface tunnel number Undo interface tunnel number 1755 Tunnel-protocol gre Syntax tunnel-protocol gre ipv6 Undo tunnel-protocol Allow l2tp L2TP Configuration Commands104 Undo allow Display l2tp session Related command l2tp-groupRelated command Display l2tp tunnel Example Sessions Syntax display l2tp tunnel Display l2tp tunnel1759 Related command allow l2tp L2tp enableL2tp sendaccm enable Syntax l2tp enable Undo l2tp enable Use the undo l2tp-group command to remove an L2TP group L2tpmoreexam enableL2tp enable L2tp-group Mandatory-chap Related command allow l2tp and start l2tpRelated command Mandatory-lcp Example Mandatory-lcp Undo mandatory-lcp Reset l2tp tunnelRelated command mandatory-chap View L2TP group view Syntax tunnel authentication Tunnel authenticationRelated command display l2tp tunnel Start l2tp Syntax tunnel avp-hidden Undo tunnel avp-hidden Undo tunnel authenticationTunnel avp-hidden 1765 Tunnel flow-control Tunnel name Tunnel password Tunnel timer hello L2TP Configuration Commands Display qos car interface Traffic Policing TP Configuration CommandsDescription on the fields of the display qos car command Filed Description Qos car Description on the fields of the display qos carl commandDisplay qos carl Display qos carl carl-index 1771 Qos carl Undo qos carl carl-index Examples # Configure Carl rule 1 with packet precedence 1773 Traffic Policing TP Configuration Commands 106 Traffic Shaping Configuration CommandsDescription on the fields of the display qos gts command Display qos gts interface Qos gts Undo qos gts any acl acl-number queue queue-number Related commands acl on 1777 Traffic Shaping Configuration Commands 107 Line Rate Configuration CommandsDescription on the fields of the display qos lr command Display qos lr interface Qos lr layer 2 interface view or port group view Qos lr interface viewUndo qos lr inbound outbound Interfaces is 4 or 9, this argument is not supported Layer 2 module interface view, port group view1781 Line Rate Configuration Commands 108 Defining Class CommandsDisplay traffic classifier Class view If-matchUndo if-match not match-criteria Match-criteria Class match rules. The values are as follow End-port 1785Value Description Rtp start-port Qos-local-id Define Mpls EXP precedence matching rule # Define a class to match ACL Related commands traffic classifier1787 # Define a class to match the IPv6 ACL named flow # Define a class to match the ACL named flow# Define a class to match IPV6 ACL # Define matching rule for all packets Traffic classifier tcl-name operator and or Traffic classifierUndo traffic classifier tcl-name By default, the relation is operator Examples # Define a class named as class1 Car Defining Traffic Behavior Commands109 Undo car Display traffic behavior Qos policy , traffic behavior , classifier behavior Filter deny permit FilterGts Undo filter Undo redirect RedirectUndo gts View Traffic behavior view Syntax remark atm-clp atm-clp-value Undo remark atm-clp Remark atm-clp1795 Syntax remark dot1p 8021p Undo remark dot1p Remark dot1pRemark dscp Syntax remark dscp dscp-value Undo remark dscp Syntax remark fr-de fr-de-value Undo remark fr-de Remark fr-de1797 Examples # Remark the DE bit in FR packets to Remark ip-precedenceRemark mpls-exp Syntax remark mpls-exp exp-value Undo remark mpls-exp Traffic behavior Remark qos-local-id1799 Examples # Define a traffic behavior named behavior1 110 Defining Policy CommandsRelated commands qos policy Classifier behavior User-defined Policy pre-defined by the user Description on the fields of the display qos policy commandSystem-defined Policy pre-defined by the system Tcl-name Class name in the policy Display qos policy interface 1803 Qos apply policy interface view EXP Qos apply policy layer 2 interface view or port group view 1805 Qos policy Syntax qos policy policy-name Undo qos policy policy-name 1807 Defining Policy Commands Qos fifo queue-length Fifo Queuing Configuration Commands111 1809 Fifo Queuing Configuration Commands 112 PQ Configuration CommandsRelated commands qos pq Display qos pq interface Examples # Display PQLs Related commands qos pq, qos pq pqlQos pq Syntax qos pq pql pql-index Undo qos pq Examples # Apply the priority list 12 to the Ethernet 1/0 Qos pql default-queueQos pql inbound-interface 1813 Description on values of queue-key and key-value By default, no classification rule is configuredQos pql protocol Queue-key Key-value Description Qos pql queue 1815 PQ Configuration Commands 113 CQ Configuration CommandsRelated commands qos cq Display qos cq interface Examples # Display information about a CQL Default values will not be displayedQos cq Syntax qos cq cql cql-index Undo qos cq Qos cql inbound-interface Qos cql default-queueExamples # Assign default queue 2 to CQL 1819 Qos cql protocol Descriptions of values of queue-key and key-value Qos cql queue 1821 Undo qos cql cql-indexqueue queue-numberserving Qos cql queue servingExamples # Specify byte-count of queue 2 in the CQL 5 to 114 WFQ Configuration CommandsRelated commands qos wfq Display qos wfq interface Undo qos wfq Qos wfqDisplay interface, display qos wfq interface Display qos cbq interface CBQ Configuration Commands115 Qos max-bandwidth Queue af Queue ef 1827 Queue wfq Syntax wred dscp ip-precedence Undo wred Queue-lengthWred 1829 Wred dscp Undo wred dscp dscp-value Wred ip-precedence 1831 Wred weighting-constant 116 RTP Priority Queue Configuration CommandsDescription on the fields of the display qos rtpq command Display qos rtpq interface Qos rtpq Qos rtpq Related commands qos reserved-bandwidth 1835 RTP Priority Queue Configuration Commands Qos qmtoken QOS Token Configuration Commands117 Qos qmtoken token-number QOS Token Configuration Commands 118 Priority Mapping Table Configuration CommandsRelated commands qos map-tabledot1p-Ip Display qos map-table Qos map-table dot1p-Ip Related commands display qos map-tableParameters in the default mapping table Import 1841 Priority Mapping Table Configuration Commands Qos priority Port Priority Configuration Commands119 Undo qos priority Port Priority Configuration Commands Display qos trust interface Port Priority Trust Mode Configuration Commands120 Qos trust Port Priority Trust Mode Configuration Commands Display qos wred interface Wred Configuration Commands121 1847 Undo qos wred enable Qos wred enableQos wred dscp ip-precedence enable Dscp Uses the Dscp value for calculating drop probability Qos wred dscp By default, the dropping method of a queue is tail dropRelated commands qos wfq, display qos wred interface 1849 Discard-probability discard-prob Qos wred weighting-constantUndo qos wred ip-precedence ip-precedence Qos wred enable, display qos wred interface Length, in the range 1 to 16. It defaults toWred with the qos wred enable command on it Calculate the average length of Wred queues Wred Configuration Commands Display qos wred table Wred Table Configuration Commands122 Syntax display qos wred table table-name Qos wred queue table Qos wfq , qos wred enable , display qos wred interfaceQos wred apply Queue Related commands qos wred queue table in system view1855 Wred Table Configuration Commands If-match mpls-exp Mpls QOS Configuration Commands123 Qos cql protocol mpls exp Related commands qos cql protocol Qos pql protocol mpls exp Examples # Set EXP value of remarked Mpls packet to Related commands qos pql protocol1859 Mpls QOS Configuration Commands Dar max-session-count DAR Configuration Commands124 Dar protocol Protocols of pre-defined ports Protocol name Protocol type Pre-defined port number 1863 Dar protocol-statistic # Restore the default name of the user-defined01 protocolDar protocol-rename Undo dar protocol-rename user-defined-name Syntax display dar information Display dar informationUndo dar protocol-statistic 1865 Display dar protocol Display dar protocol all protocol-name 1867 Display dar protocol-rename Display dar protocol-rename Display dar protocol-statistic If-match protocol If-match protocol http If-match protocol rtp Reset dar protocol-statisticUndo if-match not protocol rtp payload-type audio video All Deletes all statistics information Information, i.e. to restore the statistics toReset dar session # Deletes all statistics information DAR Configuration Commands Apply policy outbound FR QOS Configuration Commands125 # Define a traffic behavior named behavior Cir Related commands ebs, cir allow, cirCbs Undo cir Cbs, ebs, cir allow Related commandsCir allow Cir allow inbound outbound committed-information-rate Congestion-threshold Related commands cbs, ebs, cirRelated commands fr congestion-threshold Undo cq Display fr class-map Related commands wfq, pq, fr pvc-pq1879 Related commands fragment Display fr fragment-info # Display FR fragment information of a certain interfaces 1881 Display fr switch-table Fr switch 1883 PVC PQ on FR interface Display qos pvc-pq interface# Display PVC PQ information on FR interface Serial2/0 Ebs Related commands Cbs, cir allow, cir ExamplesFifo queue-length Fr class Related commands fr classRelated commands fr-class Fr congestion-threshold Fr de del Related commands congestion-threshold1887 Related commands fr de del, fr del protocol Related commands fr del inbound-interface,fr del protocolFr del inbound-interface Protocol ip IP Related commands fr de del, fr del inbound-interfaceFr del protocol 1889 Fr pvc-pq Related commands pvc-pqUndo fr pvc-pq Fr traffic-shaping Related commands fr class, fr-class,fr dlciFr traffic-policing Syntax fr traffic-policing Undo fr traffic-policing Fr-class Examples # Enable Frts on the serial interface Serial 1/0Fragment Undo fragment fragment-size Pvc-pq Related commands fr class, fr dlciRelated commands cq, wfq, fr pvc-pq Undo pq Fr pvc-pq RtpqUndo pvc-pq Number, in the range 2000 to Traffic-shaping adaptation Related commands fr traffic-shaping,cir allow, and cirUndo traffic-shaping adaptation becn interface-congestion Undo wfq Related commands cq, pq, fr pvc-pqWfq Examples # Apply WFQ to the FR class test1 126 802.1X Configuration CommandsExample # Display 802.1x configuration information Display dot1x Descriptions on the fields of the display dot1x command Undo dot1x interface interface-list Dot1xDot1x interface interface-list Dot1x # Enable 802.1x globally Dot1x authentication-methodRelated command display dot1x Syntax dot1x authentication-method chap eap pap Undo dot1x authentication-method Dot1x guest-vlan Dot1x guest-vlan vlan-id Undo dot1x guest-vlan Dot1x handshake Dot1x handshakeUndo dot1x handshake Undo dot1x max-user interface interface-list Dot1x max-userDot1x max-user user-number Undo dot1x max-user Dot1x multicast-trigger By default, the multicast trigger function is enabledDot1x port-control Dot1x port-method Dot1x port-method macbased portbased Undo dot1x port-method Syntax dot1x quiet-period Undo dot1x quiet-period Dot1x quiet-period1907 Dot1x supp-proxy-check Related command display dot1x, dot1x timerDot1x retry Undo dot1x retry 1909 Dot1x timer Reset dot1x statistics interface interface-list Reset dot1x statisticsExample # Set the server timeout timer to 150 seconds 1911 Example # Clear 802.1x statistics on port Ethernet 1/1 Accounting default AAA Configuration CommandsAccess-limit 127 AAA Configuration Commands Related command accounting default, radius scheme Accounting lan-accessAccounting login 1915 Accounting optional Undo accounting loginSyntax accounting optional Undo accounting optional Accounting portal 1917 Accounting ppp Accounting voip Related command domain, radius schemeUndo attribute access-limit idle-cut ip location mac vlan Attribute Local Performs local authentication Authentication defaultRelated command display local-user Example # Set the IP address of local user user1 to Local Performs local authentication Authentication lan-accessUndo authentication lan-access None Does not perform any authentication Authentication login Related command authentication default, radius scheme Authentication portal 1923 Undo authentication ppp Authentication pppRadius-scheme radius-scheme-name local Authorization command Authentication voip1925 Authorization default Related command authorization default, hwtacacs scheme Authorization lan-access 1927 Authorization login Related command authorization default, radius scheme Authorization portal 1929 Undo authorization ppp Authorization pppAuthorization voip Authorization default , hwtacacs scheme , radius scheme Cut connection Domain , radius scheme Display connection Display domain Related command cut connection ExampleDescription on the fields of the display connection command # Display information about all AAA user connections Related command access-limit,domain, state Description on the fields of the display domain command Related command local-user Display local-user Undo domain isp-name Domain# Display information about all local users Description on the fields of display local-user Domain default disable enable isp-name Domain defaultRelated command access-limit,state, display domain State , display domain Domain Idle-cutIp pool Domain aabbcc.net Syntax level level Related command remote address onLevel Undo level Example # Set the level of user user1 to Related command display local-user,service-typeLocal-user Example # Add a local user named user1 Password Local-user password-display-modeRelated command display local-user , password Self-service-url Service-type Related command service-type ppp and service-type ftp Service-type ftpService-type ppp Syntax service-type ftp Undo service-type ftp State State active block # Place the current user user1 to the state of blocked Related command domainWork-directory Syntax work-directory directory-name Undo work-directory 1947 AAA Configuration Commands 128 Radius Configuration CommandsAccounting-on enable Radius scheme Accounting-on enable send Accounting-on enable intervalRelated command radius scheme, accounting-on enable Mega-packet, or giga-packet Data-flow-format Radius scheme viewGigabyte Packets to be sent to a Radius server Example # Display the configurations of all Radius schemes Related command display radius schemeRelated command radius scheme Display radius scheme Example # Display statistics about Radius packets Display radius statisticsDisplay radius statistics 1953 State statistictotal=1024 State statistics 1955 Dead Time range, or user name Display stop-accounting-bufferWhich is a string of 1 to 32 characters On August 31 Nas-ip Radius scheme view Key Radius scheme viewDisplay radius scheme Primary accounting Radius scheme view Related command radius nas-ipUndo primary accounting Primary authentication Radius scheme view 1959 Radius client Syntax radius client enable Undo radius clientExample # Enable the listening port of the Radius client Radius nas-ip Undo radius nas-ip Related command nas-ip Radius scheme viewRadius scheme Undo radius scheme radius-scheme-name Radius trap Syntax reset radius statistics Reset radius statisticsReset stop-accounting-buffer Example # Clear Radius statistics Retry Undo retry Retry realtime-accounting 1965 Secondary accounting Radius scheme view Retry stop-accounting Radius scheme viewUndo secondary accounting Secondary authentication Radius scheme view 1967 Syntax server-type extended standard Undo server-type Security-policy-serverServer-type View Radius scheme view Secondary Sets the status of the secondary Radius server Use the state command to set the status of a Radius serverPrimary Sets the status of the primary Radius server Accounting Sets the status of the Radius accounting server Stop-accounting-buffer enable Radius scheme view Syntax timer quiet minutes Undo timer quiet Timer quiet Radius scheme viewTimer realtime-accounting Radius scheme view 1971 Related command retry realtime-accounting,radius scheme Timer response-timeout Radius scheme viewNumber of users Real-time accounting interval minute User-name-format Radius scheme view Related command radius scheme, retryUser-name-format with-domain without-domain Radius Configuration Commands 129 Hwtacacs Configuration CommandsRelated command display hwtacacs Data-flow-format Hwtacacs scheme view Related command hwtacacs scheme Description on the fields of the display hwtacacs command Scheme view , retry stop-accounting Hwtacacs scheme view Hwtacacs nas-ipAddress or a loopback address Hwtacacs scheme Related command nas-ip Hwtacacs scheme viewUndo hwtacacs scheme hwtacacs-scheme-name Key Hwtacacs scheme view Key accounting authentication authorization stringUndo key accounting authentication authorization string Nas-ip Hwtacacs scheme view Related command hwtacacs nas-ip Primary accounting Hwtacacs scheme view Example # Set the primary authentication server Primary authentication Hwtacacs scheme view1981 Undo primary authorization Primary authorizationReset hwtacacs statistics Accounting Clears Hwtacacs accounting statistics Retry stop-accounting Hwtacacs scheme view Syntax secondary authentication ip-address port-number Secondary authentication Hwtacacs scheme viewSecondary accounting Hwtacacs scheme view Example # Configure the secondary authentication server Secondary authorization1985 Example # Configure the secondary authorization server Stop-accounting-buffer enable Hwtacacs scheme viewView Hwtacacs scheme view Timer realtime-accounting Hwtacacs scheme view Timer quiet Hwtacacs scheme view1987 Timer response-timeout Hwtacacs scheme view User-name-format Hwtacacs scheme view Hwtacacs scheme Hwtacacs Configuration Commands Display firewall ethernet-frame-filter Packet Filter Firewall Configuration CommandsSwitch running a routing protocol All Displays all the firewall statistics information Display firewall-statistics Firewall defaultSyntax firewall default permit deny Fragments-inspect Undo firewall enable Firewall enableFirewall enable Firewall ethernet-frame-filter Example # Enable fragments inspection Firewall fragments-inspect Firewall ipv6 fragments-inspect Firewall fragments-inspect high low number defaultFirewall fragments-inspect high low Undo firewall fragments-inspect high low Related command firewall fragments-inspect Firewall packet-filter Outbound Reset firewall ethernet-frame-filterFirewall packet-filter ipv6 Undo firewall packet-filter ipv6 inbound outbound Example # Clear all the firewall statistic information Reset firewall-statistics# Clear the firewall statistic information of Ethernet 1/0 Aging-time Aspf Configuration Commands131 Aging-time syn fin tcp udp seconds # Set the UDP idle timeout period to 110 seconds # Set the TCP idle timeout period to 3000 secondsAspf-policy Syntax display aspf all Display aspf all2001 Display aspf interface Syntax display aspf interface Syntax display aspf policy aspf-policy-number Display aspf policyDisplay aspf session Display aspf session verbose Display port-mapping Example # Display all the information about port mapping Related command port-mappingFirewall aspf 2005 Example # Enable the session logging function of the Aspf Log enableSyntax log enable Undo log enable Port-mapping Syntax reset aspf session Reset aspf sessionRelated command display port-mapping Example # Map port 3456 to the FTP protocol Aspf Configuration Commands Syntax display mac-authentication interface interface-list MAC Authentication Configuration CommandsDisplay mac-authentication DFIC-9FSW and MSR 20 Series Products Mac-authentication MAC Addr Mac-authentication domain 2011 Mac-authentication timer Related command display mac-authentication Mac-authentication user-name-format Reset mac-authentication statistics Connection-limit default amount NAT Configuration CommandsConnection-limit default action 133 Undo connection-limit enable Connection-limit enableConnection-limit enable Connection-limit policy Syntax display connection-limit policy policy-numberall Display connection-limit policyExample # Create a connection-limit policy numbered 2017 Display connection-limit statistics View Any view Parameter None Display nat address-groupDisplay nat address-group Information Display nat aging-time Display nat aging-timeDisplay nat all Different NAT sessions Description on some fields of the display nat all command 2021 Display nat connection-limit Destination address Syntax display nat log Display nat logMask-length The length of net mask, in the range 1 to 2023 Display nat outbound # View the NAT log configurationDescription on the fields of the display nat log command Display nat outbound Display nat session Display nat serverSyntax display nat server Example # Display the active NAT sessions Display nat statisticsSyntax display nat statistics Display userlog export Limit acl Syntax limit mode amount Undo limit mode Limit modeView Connection-limit policy view Undo nat address-group group-number Nat address-groupNat aging-time Tcp-syn udp seconds Nat alg Nat connection-limit-policy 2031 Nat log enable Nat log flow-active Nat log flow-begin Nat log flow-beginNat outbound Undo nat log flow-begin NAT Configuration Commands Nat server # Configure the address poolNat outbound static Syntax nat outbound static Undo nat outbound static NAT Configuration Commands 2037 # Remove the WWW server using the following commands Nat static Syntax reset nat session Reset nat session2039 Related command display userlog export Reset userlog exportReset userlog nat logbuffer Userlog nat export host Userlog nat export source-ip Related command userlog nat export source-ipRelated command userlog nat export host 2041 Userlog nat syslog Userlog nat export versionSyntax userlog nat syslog Undo userlog nat syslog PKI Configuration Commands 134 Ca identifier Syntax ca identifier name Undo ca identifier Certificate request from Certificate request entityPki entity Undo certificate request mode Certificate request modeSimple password * manual Certificate request polling Undo certificate request polling count interval Related command display pki certificateCertificate request url 2047 Syntax common-name name Undo common-name Common-nameCountry Undo country Crl update-period hours Crl update-periodCrl check disable enable Undo crl update-period Display pki certificate Crl urlUndo crl url Example # Display the local certificate 2051 Display pki certificate access-control-policy Display pki certificate attribute-group Syntax display pki crl domain domain-name Related command pki retrieval-crl domain and pki domainDisplay pki crl domain Example # Display the locally saved CRLs Undo fqdn FqdnIp PKI entity view Undo ip Undo ldap-server Ldap-serverLocality Undo locality Organizational-unit OrganizationSyntax organization org-name Undo organization Pki certificate attribute-group Pki certificate access-control-policy2057 Pki domain Pki delete-certificateSyntax pki domain domain-nameundo pki domain domain-name Pki entity entity-name Pki entityPki import-certificate Undo pki entity entity-name Related command pki domain Pki request-certificate domain Pki retrieval-crl domain Related command Pki domain ExamplePki retrieval-certificate Pki retrieval-certificate ca local domain domain-name Pki validate-certificate ca local domain domain-name Pki validate-certificateRoot-certificate fingerprint Root-certificate fingerprint md5 sha1 string Syntax rule id deny permit group-name Undo rule id all Rule access control policy view2063 Undo state 135 Portal Configuration CommandsPortal authentication Display portal acl All Displays portal connection statistics on all interfaces Description on the fields of the display portal acl commandDisplay portal connection statistics Statistics on the specified interface 2067 Display portal free-rule Msgauthenack Msgauthorack Msgloginack MsglogoutackSyntax display portal free-rule rule-number Display portal interface Related command portal free-rule2069 Syntax display portal server server-name Related command portal serverDisplay portal server URL 2071 Display portal server statisticsAll Displays portal server statistics on all interfaces Reqchallenge Display portal tcp-cheat statistics Syntax display portal tcp-cheat statistics Specified interface or all interfaces enabling portal Display portal userSpecified interface enabling portal 2073 Portal auth-network Undo portal auth-network network-addressall Portal free-rule Related command display portal userPortal delete-user Undo portal free-rule rule-numberall Related command display portal free-rule Portal resource-name Undo portal server server-name key port url Related command display portal serverPortal server 2077 Reset portal connection statistics Portal server method Reset portal tcp-cheat statistics Reset portal server statisticsReset portal tcp-cheat statistics Portal Configuration Commands 136 RSH Configuration CommandsRsh INSTALL.LOG Display time-range Common Configuration CommandsDescription on the fields of the display time-range command Time-range Common Configuration Commands 2085 Common Configuration Commands Acl IPV4 ACL Configuration Commands138 2087 # Delete the IPv4 ACL with the number Acl copy# Create IPv4 ACL 2002, giving the ACL a name of flow # Delete the IPv4 ACL named flow Syntax acl name acl-name Acl name2089 # Define the description of IPv4 ACL Description for IPv4# Define the description of ACL Syntax display acl acl-numberall name acl-name Description on the fields of the display acl commandDisplay acl 2091 Rule in basic IPv4 ACL view Reset acl counterSyntax reset acl counter acl-number all name acl-name # Clear statistics about IPv4 ACL flow 2093 Rule in advanced IPv4 ACL view TCP/UDP-specific parameters for advanced IPv4 ACL rules Parameter Function Description Icmp-type Icmp message Type Code Undo rule rule-id Rule in Ethernet frame header ACL view2097 Rule in user-defined ACL view View User-defined ACL view # Create a user-defined ACL rule Support to this command varies by deviceRule comment for IPv4 Syntax rule rule-idcomment text Undo rule rule-idcomment # Create a rule in ACL 4000 and define the rule description Step for IPv4# Create a rule in ACL 3000 and define the rule description # Create a rule in ACL 5000 and define the rule description Example # Set the rule numbering step to 2 for ACL 2101 IPV4 ACL Configuration Commands Acl ipv6 IPV6 ACL Configuration Commands139 2103 # Delete the IPv6 ACL with the number Acl ipv6 copy# Create IPv6 ACL 2002, giving the ACL a name of flow # Delete the IPv6 ACL named flow Syntax acl ipv6 name acl6-name Acl ipv6 name2105 # Create a description for IPv6 ACL Description for IPv6Display acl ipv6 Syntax display acl ipv6 acl6-numberall name acl6-name 2000 to 2999 for basic IPv6 ACLs Reset acl ipv6 counterAll All basic and advanced IPv6 ACLs 3000 to 3999 for advanced IPv6 ACLs # Clear the statistics about the IPv6 ACL named flow Rule in basic IPv6 ACL viewUndo rule rule-id fragment logging source time-range Rule in advanced IPv6 ACL view 2109 Destination dest Parameter Function Description Source sourceTime-range time-name ICMPv6-specific match criteria for advanced IPv6 ACL rules TCP/UDP-specific match criteria for advanced IPv6 ACL rulesAvailable ICMPv6 messages Rule in simple IPv6 ACL view View Simple IPv6 ACL view Parameters for simple IPv6 ACL rules ICMPv6-specific parameters for simple IPv6 ACL rules TCP/UDP-specific parameters for simple IPv6 ACL rulesICMPv6 messages definable in simple IPv4 ACL rules Rule comment for IPv6 Support for this command varies by device2115 Step for IPv6 Example # Set the rule numbering step to 2 for IPv6 ACL # Set the rule numbering step to 2 for IPv6 ACL 2117 IPV6 ACL Configuration Commands Cryptoswitch fabric enable Ipsec Configuration CommandsAh authentication-algorithm 140 Display encrypt-card fast-switch Syntax display encrypt-card fast-switch Display ipsec policy brief name policy-name seq-number Display ipsec policyIpsec policy system view # Display detailed information about all IPSec policies 10000 Display ipsec policy-templateIPSec policy template group Template group Display ipsec sa Related command ipsec proposalDisplay ipsec proposal Syntax display ipsec proposal proposal-name Reset ipsec sa, ipsec sa global-duration Description on the fields of the display ipsec sa command Syntax display ipsec session tunnel-id integer Related command reset ipsec sessionDisplay ipsec session Example # Display information about all IPSec sessions Syntax display ipsec statistics Related command reset ipsec statisticsDisplay ipsec statistics Example # Display IPSec packet statistics Syntax display ipsec tunnel Display ipsec tunnel2129 Encrypt-card fast-switch Encapsulation-mode Esp encryption-algorithm Esp authentication-algorithmRelated command display encrypt-cardfast-switch Syntax esp encryption-algorithm 3des aes key-length des Undo esp encryption-algorithm Ike-peer IPSec policy view/IPSec policy template viewSyntax ike-peer peer-name Undo ike-peer peer-name Ipsec binding policy Related command ipsec policy-template2133 Ipsec cpu-backup Syntax ipsec cpu-backup enable Undo ipsec cpu-backup enable Ipsec policy interface view 2135 Ipsec policy system view Syntax ipsec policy policy-nameseq-number isakmp manual Undo ipsec policy-template template-name seq-number Ipsec policy isakmp templateIpsec policy-template 2137 Related command display ipsec proposal Related command display ipsec policy-templateIpsec proposal Ipsec session idle-time Related command sa duration, display ipsec sa durationIpsec sa global-duration Example # Create an IPSec proposal named newprop1 Pfs dh-group1 dh-group2 dh-group5 dh-group14 PfsUndo ipsec session idle-time Undo pfs Proposal Example # Enable and configure PFS for IPSec policy policy1Related command ipsec proposal, ipsec policy system view Undo proposal proposal-name Reset ipsec sa Reset encrypt-card fast-switchSyntax reset encrypt-card fast-switch Related command display ipsec sa Reset ipsec sessionSyntax reset ipsec session tunnel-id integer Related command display ipsec session Reset ipsec statisticsSa authentication-hex Syntax reset ipsec statistics View IPSec policy view/IPSec policy template view Sa duration2145 Sa encryption-hex Sa spi 2147 Sa string-key Syntax security acl acl-number Undo security acl Example # Configure IPSec policy policy1 to reference ACLSecurity acl 2149 Tunnel local Example # Configure IPSec proposal prop1 to use AHTransform Syntax transform ah ah-esp esp Undo transform Tunnel remote 2151 Example # Set the remote address of the IPSec tunnel to 141 IKE Configuration CommandsIke proposal, display ike proposal Dh group1 group2 group5 group14 Related command ike proposal, display ike proposalCertificate domain Undo dh Example # Specify 768-bit Diffie-Hellman for IKE proposal Related command ike dpdDisplay ike dpd Syntax display ike dpd dpd-name Display ike proposal Related command ike peer system viewDisplay ike peer Syntax display ike peer peer-name Display ike sa Example # Display the settings of IKE proposalsRelated command ike proposal, ike peer system view 2157 # Display detailed information about the current IKE SAs 2159 Undo dpd DpdEncryption-algorithm 3des-cbc aes-cbc key-length des-cbc Exchange-mode Related command Id-type ExampleId-type Example # Use the ID type of name in IKE negotiation Ike dpdIke local-name Syntax ike dpd dpd-name Undo ike dpd dpd-name Example # Configure the local gateway name as app Ike next-payload check disabledRelated command remote-name,id-typename 2163 Ike proposal Related command display ike proposalIke peer system view Syntax ike peer peer-name Undo ike peer peer-name Related command ike sa keepalive-timer timeout Ike sa keepalive-timer intervalIke sa keepalive-timer timeout Example # Set the keepalive interval to 200 seconds Example # Set the keepalive timeout to 20 seconds Ike sa nat-keepalive-timer intervalRelated command ike sa keepalive-timer interval Interval-time Local Local-address Peer multi-subnet single-subnet Nat traversalSyntax nat traversal Undo nat traversal Undo peer Remote-address Related command authentication-algorithmonPre-shared-key Syntax pre-shared-key key Undo pre-shared-key Related command id-type,ike local-name Reset ike saRelated command id-typeip, local-address Remote-name Syntax sa duration seconds Undo sa duration Related command display ike saExample # Clear the IPSec tunnel to 2171 Time-out Related command ike proposal and display ike proposalSyntax time-out time-out Undo time-out Display public-key local SSH2.0 Configuration Commands142 Public-key local create Example Brief Displays brief information about all public keys Display public-key peerDisplay public-key peer brief name publickey-name Specified or all public keys # Display brief information about all public keys Related command sftp client sourceDisplay sftp client source Syntax display sftp client source Display ssh server Related command ssh client sourceDisplay ssh client source Syntax display ssh client source Syntax display ssh server-info Display ssh server-info# Display the session information of the SSH server 2177 Syntax display ssh user-information username Related command ssh userDisplay ssh user-information Example # Display information about all SSH users Public-key-code begin Related command Public-key peer ExamplePeer-public-key end Peer-public-key end Public-key-code end Public-key-code endPublic-key local create Public-key peer, public-key-code begin # Create local RSA key pair Public-key local destroyPublic-key local destroy, display public-key local Example # Create local DSA key pair Public-key local export rsa openssh ssh1 ssh2 filename Related command public-key local createPublic-key local export rsa Public-key local create , public-key local destroy Public-key local export dsa openssh ssh2 filename Public-key local export dsa# Display the RSA local public key in OpenSSH format # Export the DSA local public key in OpenSSH format # Display the DSA local public key in OpenSSH format Related command public-key-code begin, public-key-code endPublic-key peer Syntax public-key peer keyname Undo public-key peer keyname Sftp Public-key peer import sshkey2185 Undo sftp client ipv6 source Sftp client ipv6 sourceIpv6 ipv6-address Specifies a source IPv6 address Sftp client source Related command Display sftp client source ExampleSftp ipv6 Sysname sftp ipv6 Input Username Syntax sftp server enable Undo sftp server enable Sftp server enableSftp server idle-timeout Related command display ssh server Ssh client authentication server Ssh client first-time enable Ssh client source To access the SSH serverSsh client ipv6 source Undo ssh client ipv6 source Ssh server authentication-retries Related command display ssh client source By default, the authentication timeout period is 60 seconds Ssh server authentication-timeoutSsh server compatible-ssh1x enable Example # Enable the SSH server to work with SSH1.x clients Syntax ssh server enable Undo ssh server enable Ssh server enableSsh server rekey-interval Undo ssh user username Ssh user2195 Related command display ssh user-information Ssh2 Ssh2 ipv6 2197 SSH2.0 Configuration Commands 2199 SSH2.0 Configuration Commands Bye Sftp Configuration Commands143 Syntax bye Dir CdupDelete Syntax cdup Syntax exit ExitGet 2203 Help Put Mkdir2205 Syntax pwd PwdQuit Syntax quit Rmdir RemoveRename 2207 Sftp-client rmdir temp1 Directory successfully removed Ciphersuite SSL Configuration Commands144 View SSL server policy view Example # Set the SSL connection close mode to wait Client-verify enableSyntax client-verify enable Undo client-verify enable Close-mode wait Syntax display ssl client-policy policy-nameall Display ssl client-policyDisplay ssl server-policy Syntax display ssl server-policy policy-nameall Pki-domain Handshake timeoutSyntax handshake timeout time Undo handshake timeout Syntax pki-domain domain-name Undo prefer-cipher Prefer-cipherUndo pki-domain 2213 Session Session cachesize size timeout timeUndo session cachesize timeout Rsaaes128cbcsha Ssl server-policy Ssl client-policy2215 SSL client policy view Use the undo version command to restore the defaultVersion ssl3.0 tls1.0 Ssl3.0 Specifies SSL Display standby flow Backup Center Configuration CommandsSyntax display standby flow Display standby state Main and backup interfacesDisplay standby state Following tables describe the meanings of each state Standby bandwidth Backup states of the backup interfaceBackup flags Syntax standby bandwidth size Undo standby bandwidth Related command standby interface Standby interface Undo standby threshold Related commands standby trackStandby threshold 2221 Related command standby interface and standby bandwidth Standby timer delayUndo standby timer delay Undo standby track Standby timer flow-checkStandby track 2223 Standby interface, track on IPV4-BASED Vrrp Configuration Commands Display vrrp Vrrp vrid track command Description on the fields of the display vrrp commandVrrp vrid track interface command Display vrrp statistics Example # Display the statistics about all standby groups 2227 255 Reset vrrp statisticsVrrp vrid authentication-mode Device are cleared Syntax vrrp method real-mac virtual-mac Undo vrrp method Vrrp method2229 Undo vrrp ping-enable Vrrp ping-enableVrrp ping-enable Addresses of standby groups Vrrp vrid preempt-mode Default mode is immediate preemption without delayVrrp un-check ttl Syntax vrrp un-check ttl Undo vrrp un-check ttl Vrrp vrid priority Vrrp vrid track Vrrp vrid timer advertise2233 Vrrp vrid track interface Vrrp vrid virtual-ip 2235 # Add virtual IP address 10.10.10.11 to standby group Display vrrp ipv6 Vrrp Configuration Commands For IPV6147 IPv6 Vrrp ipv6 vrid track command Display vrrp ipv6 statistics 2239 Vrrp ipv6 method Reset vrrp ipv6 statisticsSyntax vrrp ipv6 method real-mac virtual-mac Undo vrrp ipv6 ping-enable Vrrp ipv6 ping-enableVrrp ipv6 ping-enable Undo vrrp ipv6 method Vrrp ipv6 vrid authentication-mode Vrrp ipv6 vrid preempt-mode Undo vrrp ipv6 vrid virtual-router-idpriority Vrrp ipv6 vrid priority2243 Vrrp ipv6 vrid timer advertise Undo vrrp ipv6 vrid virtual-router-idtimer advertise Vrrp ipv6 vrid track 2245 # Configure the virtual IPv6 address of standby group 1 as Vrrp ipv6 vrid virtual-ip Device Management Commands 148 Syntax buzzer enable Undo buzzer enable BootromBuzzer enable Part Display boot-loader slot slot-number Display boot-loaderThis command is applicable on MSR 50 series routers only Related command Boot-loader Display cpu-usage Display cpu-usage task number offset verbose from-device Syntax display device cf-card usb slot slot-numberverbose Description on fields of the display boot-loader commandDisplay device 2251 Varies with devices Cf-card Displays information of a compact Flash CFUsb Displays information of a universal serial bus USB Such as card, CF, USB, VCPM, VPM and DSP 2253 Description on fields on the display device commandCpld Information about the device Display device manuinfoDisplay device manuinfo slot slot-number Display Example # Display manufacturing information of a device # Display the temperature information of cardsDisplay environment Display environment Display fan fan-id Display fanDisplay license Display license Display memory Display powerSyntax display power power-id Syntax display memory Display reboot-type slot slot-number Display reboot-typeDisplay schedule reboot Display schedule reboot Reboot slot slot-number RebootOnly users at management level can execute this command License register Syntax reset unused porttag Reset unused porttagUse the remove command to remove a card Remove slot slot-number Syntax schedule reboot at hhmm date Undo schedule reboot Schedule reboot at2261 Schedule reboot delay Syntax schedule reboot delay hhmm mm Undo schedule reboot Temperature-alarm enable 2263 Temperature-limit Undo temperature-limit slot-number Data-fill NQA Client Configuration CommandsSyntax data-fill string Undo data-fill Description any NQA test type view Data-sizeSyntax data-size size Undo data-size Syntax destination ip ip-address Undo destination ip Destination ipDestination port Syntax destination port port-number Undo destination port Result Displays the results of the last test Syntax display nqa result history admin-nameoperation-tagDisplay nqa History Displays the history records of a test Description on the fields of the display nqa result command 2269 # Display the history records of tests Field Description Index History record number Syntax filename filename Undo filename FilenameFrequency Syntax frequency interval Undo frequency History-records Syntax history-records number Undo history-records Http-version Http-versionNext-hop Undo http-version Related command nqa server enable Nqa agent enableSyntax nqa agent enable Undo nqa agent enable Nqa Nqa schedule Example # Enable the NQA clientNqa agent max-concurrent 2275 Operation get put Operation FTP test type viewOperation Http test type view Undo operation Operation interface Password FTP test type viewSyntax password password Undo password Undo operation interface Probe count Syntax probe count times Undo probe count Probe packet-number Probe packet-interval2279 Probe timeout Probe packet-timeoutSyntax probe timeout timeout Undo probe timeout Reaction 2281 Route-option bypass-route Reaction trapUndo reaction trap probe-failure test-complete test-failure Undo source interface Related command source ipSource interface 2283 Source port Related command source interfaceSource ip Syntax source ip ip-address Undo source ip Syntax tos value TosTtl Syntax ttl value Type Syntax url url UrlUsername FTP test type view Undo url Vpn-instance ICMP-echo test type view Syntax vpn-instance instance Undo vpn-instance Display nqa server status NQA Server Configuration Commands150 Syntax display nqa server status Related command nqa server tcp-connect,nqa server udp-echo Nqa server enableSyntax nqa server enable Undo nqa server enable Example # Enable the NQA server Undo nqa server udp-echo ip-addressport-number Nqa server udp-echo2291 Sysname nqa server udp-echo 169.254.10.2 Display ip netstream cache Netstream Configuration CommandsSyntax display ip netstream cache Display ip netstream export Ip netstream statistics commandDisplay ip netstream export Exported NetStream UDP packets Undo enable EnableSyntax enable Related command ip netstream aggregation Ip netstream aggregation Source-prefix Example # Enter NetStream AS aggregation view Ip netstream export hostIp netstream export source 2297 Ip netstream export version Ip netstream max-entry Ip netstream timeout activeRelated command ip netstream timeout inactive 2299 Related command ip netstream timeout active Ip netstream timeout inactiveReset ip netstream statistics Reset ip netstream statistics Syntax display ntp-service sessions verbose NTP Configuration CommandsDisplay ntp-service sessions 152 Display ntp-service status Display ntp-service statusExample # View the NTP service status information Syntax display ntp-service trace Display ntp-service trace2303 Protection. a more secure method is identity authentication Ntp-service accessUndo ntp-service access peer query server synchronization Sure you have already created and configured this ACL By default, NTP authentication is disabled Ntp-service authentication enableNtp-service authentication-keyid # Enable NTP authentication Ntp-service broadcast-client Ntp-service broadcast-server Ntp-service in-interface disable 2307 Ntp-service max-dynamic-sessions Ntp-service multicast-client Undo ntp-service multicast-server ip-address Ntp-service multicast-serverNtp-service refclock-master 2309 Undo ntp-service source-interface Ntp-service reliable authentication-keyidNtp-service source-interface Used as a reference clock Ntp-service unicast-peer Vpn-instance-name in your command Ntp-service unicast-serverPublic network Interface and the NTP server coexist in this VPN No NTP server is designated for the device by defaultDesignated for the device 2313 NTP Configuration Commands Syntax display rmon alarm entry-number Rmon Configuration CommandsDisplay rmon alarm Related command rmon alarm Description on the fields of the display rmon event command Related command rmon eventExample # Display the configuration of Rmon event table Display rmon event Syntax display rmon eventlog entry-number Display rmon eventlogDisplay rmon history 2317 Related command rmon history Related command rmon prialarm Display rmon prialarmSyntax display rmon prialarm entry-number Current-configuration and display this commands you cannot With the display current-configuration and display Related command rmon statisticsDisplay rmon statistics Undo rmon alarm entry-number Rmon alarm2321 You can create up to 60 alarm entries Table with the rmon event commandRising alarm and falling alarm are alternate Rmon event Undo rmon history entry number You can create up to 100 alarm entriesRmon history Display rmon history Undo rmon prialarm entry-number Rmon prialarm2325 You can create up to 50 pri-alarm entries Configurations the same and the creation fails# Remove private alarm entry Rmon statistics 2327 Rmon Configuration Commands 154 Snmp Configuration CommandsDisplay snmp-agent local-switch fabricid Display snmp-agent community Syntax display snmp-agent group group-name Display snmp-agent groupDescriptions on the fields of display snmp-agent community Name of the specified MIB view Display snmp-agent mib-view2331 Display snmp-agent statistics Syntax display snmp-agent statistics Version Displays the version of the current Snmp agent Display snmp-agent sys-infoDisplay snmp-agent sys-info contact location version 2333 Display snmp-agent trap-list Related command snmp-agent trap enableSyntax display snmp-agent trap-list Display snmp-agent usm-user Enable snmp trap updownSyntax enable snmp trap updown Undo enable snmp trap updown # Display SNMPv3 information for the user aa Snmp-agent Snmp-agentUndo snmp-agent Snmp-agent community Undo snmp-agent community community name Snmp-agent group Undo snmp-agent group v3 group-name authentication privacyRelated command snmp-agentmib-view,snmp-agentusm-user Undo snmp-agent group v1 v2c group-name Snmp-agent log Snmp-agent local-switch fabricidSnmp-agent usm-user Snmp-agent mib-view Undo snmp-agent mib-view view-name Snmp-agent sys-info Related command snmp-agent groupSnmp-agent packet max-size 2341 Related command Display snmp-agentsys-info Snmp-agent target-host 2343 Snmp-agent trap enable Linkup warmstart * system voice vrrp authfailure newmaster Undo snmp-agent trap if-mib link extended Snmp-agent trap if-mib link extendedSnmp-agent trap if-mib link extended NMS, the device may not be able to resolute the messages Snmp-agent trap life Snmp-agent trap queue-size Snmp-agent usm-user Example # Configure the size of the Trap queue toSnmp-agent trap source Undo snmp-agent trap source Parameter v1 SNMPv1 2349 Snmp Configuration Commands File System Configuration Commands Copy Syntax delete /unreserved file-url Syntax dir /all file-url Syntax execute filename Execute2353 File prompt alert quiet File promptFixdisk Syntax fixdisk device # create a subdirectory named mytest under test FormatSyntax format device 2355 Syntax more file-url MoreMount Syntax mount device # Mount a CF card on a centralized device Related command Example UmountMove 2357 Example # Move the file cf/test/sample.txt to cf/sample.txt Reset recycle-binSyntax reset recycle-bin /force Example # Rename the file sample.txt as sample.bak Syntax umount device Umount2359 Example # Unmount a CF card on a device Related command mountUndelete Syntax undelete file-url Display saved-configuration Configuration File Management CommandsBackup startup-configuration Syntax display saved-configuration by-linenum Configuration File Management Commands Reset saved-configuration backup main Reset saved-configurationRelated command startup saved-configuration Display startup Restore startup-configuration Related command save, display saved-configuration Save Syntax save file-name safely backup main2365 Startup saved-configuration Related command display startup 2367 Configuration File Management Commands 157 FTP Server Configuration CommandsRelated command ftp timeout and ftp update Display ftp-server Description on the fields of the display ftp-user command Ftp server enableSyntax ftp server enable Undo ftp server Free ftp user Syntax ftp timeout minute Undo ftp timeout Ftp timeoutFtp update Syntax ftp update fast normal Undo ftp update Sysname system-view Sysname ftp update normal Ascii FTP Client Configuration Commands158 Binary Syntax cd pathname Syntax close CloseDebugging Syntax debugging Undo debugging Description on the fields of the debugging command View FTP client view Parameter remotefile File name Syntax disconnect # View the content of aa.txtDisconnect 2377 Related command ftp client source Display ftp client configurationSyntax display ftp client configuration Ftp Ftp client source Ftp client sourceUndo ftp client source Related command display ftp client configuration Ftp ipv6 2381 Lcd Syntax lcd Open # View the content of file aa.txt2383 Related command close Open ipv6 Undo passive PassiveSyntax passive 2385 Parameter protocol-command FTP command Remotehelp Description on the fields of the remotehelp command # Display the help information for the user command2387 Syst NlstSite Stat Undo verbose VerboseSyntax verbose 2389 FTP Client Configuration Commands 159 Tftp Client Configuration CommandsDisplay tftp client configuration Tftp-server acl Tftp # Associate IPv6 ACL 2001 with Tftp application in Ipv6 Tftp client source Related command tftp client sourceIP address configured on the device On the source interface, the transmission fails Related command display tftp client configuration Tftp ipv6 2395 Tftp Client Configuration Commands 160 System Maintaining CommandsPing Ping ipv6 2399 Tracert Tracert ipv6 Range 1 to 65535, defaulting to65535, in milliseconds. The default value is 5000 ms With IPv6 address System Maintaining Commands Undo debugging all module-name option System Debugging Commands161 View User view Parameter all All debugging functions Display debugging Related command display debuggingDebugging Clock datetime Basic Configuration Commands162 Clock summer-time one-off Basic Configuration Commands Clock summer-time repeating 2407 Clock timezone Undo command-privilege view view command Command-privilegeCommand-privilege level level view view command Display clock Display configure-user Configure-user countDescription Related command Display clipboard Display clock Display configure-userSyntax display configure-user Syntax display clock Related command configure-user count Display current-configurationExclude text Special characters in regular expression 2413 Display diagnostic-information Display diagnostic-information# Display the configuration beginning with user Version, display device, display current-configuration Display hotkey Display history-commandSyntax display history-command Display hotkey Display this Syntax display this by-linenum Syntax display version Display version2417 Undo header incoming legal login motd shell Header incoming legal login motd shell textHeader Hotkey Hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu commandCtrl+G corresponds to display current-configuration Undo hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu # Display the configuration of hotkeys Super Related command quitReturn Syntax return Super password level user-level simple cipher password Super passwordRelated command super password Undo super password level user-level Syntax sysname sysname Undo sysname # Display the password for switching user-levelSysname 2423 Syntax system-view Related command quit, returnSystem-view Example # Enter system view from the current user view Display channel Information Center Configuration CommandsDescription on the fields of the display channel command Example # Display information for channel Display info-center Syntax display info-center Description on the fields of the display info-center command 2427 Severity description Display logbufferRepresents information level, in the range 0 to Meanings of characters in text Rest is omitted here Descriptions on the fields of the display logbuffer command2429 Display logbuffer summary level severity Display logbuffer summaryDisplay logfile buffer Syntax display logfile buffer Display logfile summary Support for the command varies with devicesExample # Display the contents of the log file buffer Syntax display logfile summary Display trapbuffer size buffersize Display trapbufferInfo-center channel name Trap buffer, in the range 1 to 1,024 Info-center console channel 2433 Info-center logbuffer Info-center enableSyntax info-center enable Undo info-center enable Undo info-center logbuffer channel size Info-center logfile frequency Info-center logfile enableExample # Enable the log file feature 2435 Syntax info-center logfile switch-directory dir-name Info-center logfile switch-directoryInfo-center logfile size-quota Undo info-center loghost host-ip Info-center loghost# Set the directory to save the log file to cf/test 2437 Info-center loghost source Undo info-center loghost source Undo info-center snmp channel Info-center monitor channelInfo-center snmp channel 2439 Info-center source 2441 Default output rules for different output directionsOutput Modules Enabled Direction Allowed Disabled Severity NMS Info-center synchronous Info-center timestamp Info-center timestamp loghost date no-year-date none Info-center timestamp loghostUndo info-center timestamp loghost Undo info-center trapbuffer channel size Info-center trapbufferLogfile save Syntax logfile save Reset trapbuffer Reset logbufferTerminal debugging Undo terminal debugging Terminal loggingSyntax terminal logging Undo terminal logging Terminal monitor Terminal trapping Sysname terminal trapping Current terminal trapping is on Undo acl ipv6 acl-number inbound outbound User Interface Configuration CommandsAcl ipv6 acl-number inbound outbound Acl acl-number inbound Activation-key Syntax activation-key character Undo activation-key Auto-execute command 2451 AAA, refer to AAA Configuration Commands on None Performs no authenticationPassword Performs local password authentication Users log onto the device using the current user interface Databits 5 6 7 DatabitsUndo databits History-commandmax-size Display history-commandDisplay user-interface # Display summary about all user interfaces 2455 Display users all Description on the fields of the display users commandDisplay users All Displays information about users on all user interfaces Example # Define a as the escape key Syntax escape-key default character Undo escape-keyEscape-key 2457 None Syntax free user-interface num1 aux console tty vty num2 Free user-interface2459 # Terminate the connection with user interface VTY History-command max-sizeView User interface view Lock Password next time you enter the systemLock Operating under the active user interface Only, and cannot be applied to the Console port Parity Example # Set the answering mode to auto-answerExample # Set the timeout interval to 50 seconds Syntax parity even mark none odd space Undo parity Example # Perform odd parity check on the AUX interface Example # Enable the VTYs 0 through 4 to support SSH onlyProtocol inbound Syntax protocol inbound all pad ssh telnet Undo redirect enable Redirect enableRedirect enable Redirect disconnect Redirect refuse-negotiation Related command telnet, display tcp statistics onRedirect listen-port Redirect listen-port port-number Redirect return-deal from-telnet Redirect return-deal from-telnetUndo redirect return-deal from-telnet Redirect timeout Redirect return-deal from-terminal Syntax screen-length screen-length Undo screen-length Screen-lengthSend Syntax send all num1 aux console tty vty num2 Set authentication password cipher simple password Set authentication passwordUndo set authentication password Syntax shell Related command authentication-modeShell Undo shell Speed in user interface view Stopbits Terminal type User privilege level Syntax user privilege level level Undo user privilege level User-interface # Enable user 1 to access level 3 commands# Enter the user interface view of VTY 0 to User Interface Configuration Commands Ethernet interfaces MAC Address Table Management Configuration CommandsDisplay mac-address Display mac-address blackhole vlan vlan-id count Syntax display mac-address aging-time Display mac-address aging-timeDisplay mac-address mac-learning Port Index Mac-address Ethernet interface view 2479 Blackhole MAC address entries are dropped Related command display mac-addressMac-address system view Specified Vlan ID, in the range 1 to Mac-address mac-learning disable 2481 Example # Disable global MAC address learning Related command display mac-addressmac-learningMac-address max-mac-count Ethernet interface view Mac-address timer aging seconds no-aging Mac-address timerUndo mac-address timer aging MAC Address Table Management Configuration Commands 166 POE Configuration CommandsApply poe-profile Display poe device Module, and slot of the power sourcing equipment PSEDescription on fields of the display poe device command Display poe interface 2487 Description on fields of the display poe interface command # Display the state of all PoE interfaces Display poe interface power 2489 # Display the power information of all PoE interfaces Display poe power-usageSyntax display poe power-usage Syntax display poe pse pse-id Display poe pse2491 Syntax display poe-power Display poe-powerDescription on fields of the display poe pse command Description on fields of the display poe-power command 2493 Display poe-profile index index name profile-name Existing PoE configuration files will be displayedDisplay poe-profile Number ranges from 1 to Description on fields of the display poe-profile command 2495 Poe disconnect Display poe-profile interfaceSyntax poe disconnect ac dc Undo poe disconnect Poe enable Syntax poe enable Undo poe enable Poe enable pse Poe legacy enable Syntax poe max-power max-power Undo poe max-power Poe max-powerPoe max-power system view 2499 Poe mode signal spare Poe modeRelated command poe priority system view Undo poe mode Syntax poe pd-description string Undo poe pd-description Poe pd-descriptionPoe pd-policy priority Syntax poe pd-policy priority Undo poe pd-policy priority Poe priority Syntax poe priority critical high low Undo poe priority Poe priority critical high low pse pse-id Poe priority system viewUndo poe priority pse pse-id Poe pse-policy priority Poe updatePoe update full refresh filename pse pse-id Poe pse-policy priority Poe-profile Example # Set the power alarm threshold of PSE 2 to 90%Poe utilization-threshold Undo poe utilization-threshold pse pse-id Sysname system-view Sysname poe-profile abc Oap connect slot OAP Module Configuration CommandsSyntax oap connect slot slot-number Oap reboot slot Syntax oap reboot slot slot-number 168 Acfp Configuration CommandsAcfp enable Display acfp client-info Policy-index Policy index, in the range of 1 to Display acfp policy-infoClient-idis the Acfp client ID, in the range of 1 to Interface-numberis the interface type and interface number 2511 Interface-number is the interface type and interface number Display acfp rule-cacheInterface type and interface number Will display all the Acfp rule cache information Client-id Acfp client ID, in the range of 1 to Display acfp rule-infoInterface number 2513 # Display Acfp rule information in order of policy Establish Syntax display acfp server-info Display acfp server-info2515 Reset acfp rule-cache Type and interface number Syntax acsei server enable Undo acsei server enable Acsei Server Configuration CommandsAcsei server enable Acsei server Acsei timer monitor Acsei timer clock-syncSyntax acsei timer monitor seconds Undo acsei timer monitor Acsei client close Acsei client rebootDisplay acsei client summary # Display the summary of all Acsei clients Display acsei client infoSyntax display acsei client info client-id # Display information about all Acsei clients 2521 CPU information of the Acsei client Acsei-client debug enable Acsei Client Configuration CommandsAcsei-client debug disable 170 Acsei-client debug show Chkconfig acseid offSyntax chkconfig acseid off Syntax acsei-client debug show Syntax chkconfig acseid on Chkconfig acseid onService acseid condrestart Syntax service acseid condrestart Service acseid reload Service acseid reloadService acseid restart # Load the Acsei client configuration file Syntax service acseid start Service acseid startService acseid status Syntax service acseid status Any directory of the Linux system Service acseid stopService acseid stop # Stop an Acsei client that is running 171 Track Configuration CommandsDescription on the fields of the display track command Display track Track Configuration Commands 172 IPX Configuration CommandsDisplay ipx interface Display ipx routing-table Syntax display ipx routing-table network Syntax display ipx routing-table network verbose Display ipx routing-table verbose2533 Display ipx routing-table protocol Display ipx routing-table statistics Display ipx service-tableInactive Displays inactive service information To 47 characters Display ipx statistics # Display detailed IPX service informationSyntax display ipx statistics 2537 SAP Undo ipx enable Ipx enableIpx enable node node Configuration Ipx encapsulation Ipx netbios-propagationSyntax ipx netbios-propagation Undo ipx netbios-propagation Ipx encapsulation dot2 dot3 ethernet-2 snap Undo ipx network Ipx networkIpx rip import-route static Ipx rip import-route static Ipx rip multiplier Example # Enable static route redistribution to RIPIpx rip mtu Syntax ipx rip mtu bytes Undo ipx rip mtu Related command ipx rip multiplier Ipx rip timer updateRelated command ipx rip timer update Example # Specify a RIP update interval of 30 seconds Ipx route load-balance-path 2543 Syntax ipx sap disable Undo ipx sap disable Ipx sap disableIpx route max-reserve-path Undo ipx sap gns-disable-reply Ipx sap gns-disable-replyIpx sap gns-disable-reply Ipx sap gns-load-balance Ipx sap mtu Related command ipx sap gns-disable-replyIpx sap max-reserve-servers Syntax ipx sap mtu bytes Undo ipx sap mtu Related command ipx sap timer updateIpx sap multiplier 2547 Related command ipx sap multiplier, ipx update-change-only Ipx sap timer updateIpx service Example # Specify the SAP updating interval as 300 seconds Ipx split-horizon Ipx split-horizonIpx tick Undo ipx split-horizon Syntax ipx update-change-only Undo ipx update-change-only Ipx update-change-onlyPing ipx Syntax reset ipx statistics Reset ipx statisticsReset ipx routing-table statistics protocol 2551 Example # Display IPX routing statistics Related command display ipx routing-table statistics# Clear IPX static route statistics Voip Configuration Commands 173 Area custom europe north-america AreaArea-id Undo area Syntax busytone-t-th time-threshold Undo busytone-t-th Related command match-template,address, and entityBusytone-t-th 2555 Syntax cid display Undo cid display Cid displayCid receive Syntax cid receive Undo cid receive Syntax cid send Undo cid send Cid sendCid type View FXS/FXO voice subscriber line view Syntax cng-on Cng-onUndo cid type Undo cng-on View POTS/VoIP/VoFR entity view Related command line and vad-onCompression 2559 Relationship between algorithms and bandwidth Codec Bandwidth Voice quality 723 r53 algorithm 711 algorithm A-law and µ-law723 r63 algorithm 726 r16 algorithm 726 r32 algorithm 726 r24 algorithm726 r40 algorithm Algorithm Compression efficiency of IPHC+PPP header Regions are supported Cptone country-typeSyntax cptone country-type locale Undo cptone country-type Countries or regions with supported call progress tones 2565 IEU Special-dial-tone waiting-tone amplitude value Cptone tone-typeEffect on all voice interfaces of all cards on the device Special-dial-tone waiting-tone amplitude Default entity compression G729r8 Default entity payload-size Related command compression Undo default entity vad-on Default entity vad-onDefault entity vad-on Vad-on Delay hold Default subscriber-lineTransmit gain Related command em-signal Delay risingDelay send-dtmf Syntax delay rising milliseconds Undo delay rising Delay send-wink Syntax delay send-wink milliseconds Undo delay send-wink Syntax delay wink-hold milliseconds Undo delay wink-hold Delay wink-holdDelay wink-rising 2573 Syntax delay start-dial seconds Undo delay start-dial Delay start-dialDescription voice entity view Syntax dial-program Description voice subscriber line viewDial-program View Voice view Range of 0 to Display voice call-infoDisplay voice call-info brief mark tag verbose Information table Display voice cmc LGS Description on fields of the display voice cmc command Display voice default allSyntax display voice default all 2579 Description on fields of the display voice default command Display voice ipp statistic Display voice entity command ExampleDisplay voice entity Display voice entity all mark entity-tag pots voip Voip Configuration Commands Call Displays the calling statistics in the IVA module Error Displays all the error statistics of IVA moduleDisplay voice iva statistic 2583 Display voice subscriber-line Related command subscriber-lineSyntax display voice subscriber-line line-number 2585 = Busytone CNG Syntax dscp media dscp-value Undo dscp media Dscp mediaDtmf amplitude Syntax dtmf amplitude value Undo dtmf amplitude Dtmf time interval persist milliseconds Dtmf sensitivity-levelDtmf time Undo dtmf time interval persist 2589 Dtmf thresholdMeaning of the index numbers Index Meaning Value range Remarks Upper limit of the maximum To 4,999, with Echo-canceller 2591 Mix-proportion-ratio value talk-threshold value Echo-canceller parameterRelated command subscriber-lineand echo-canceller parameter Mix-proportion-ratio talk-threshold Related command echo-canceller Em-signalEm-phy-parm Entity entity-number pots voip EntityUndo entity entity-numberall pots voip Fast-connect Related command Line ExampleRelated command outband, tunnel-on, and voip called-start Fast-connect Syntax hookoff-mode delay immediate Undo hookoff-mode Hookoff-mode delay bindExample # Enable fast connection for VoIP voice entity Hookoff-mode Incoming calls Private-lineand caller-permitcommands when executingHookoff-time Syntax hookoff-time time Undo hookoff-time Impedance Undo line LineMatch-template Syntax match-template match-string Undo match-template Format . Other formats, such as and are illegal ThemIf you want to use and at the same time, you must use them Such as 0-9. The formats like 0-A are illegal E1 voice, T, #, and * are not supported currently Command, but analog voice subscriber lines do notNlp-on Nlp-on Outband Related command Fast-connectand tunnel-on ExamplePayload-size Syntax plc-mode general specific Undo plc-mode Plc-mode2603 Receive gain Related command transmit gain and subscriber-lineSyntax receive gain value Undo receive gain Register-number Reset voice cmc statisticMatch-template Related command display voice iva statistic Reset voice ipp statisticReset voice iva statistic Related command display voice ipp statistic Send-busytone Send-busytone enable time secondsUndo send-busytone enable time Been used to identify nonstandard T38 fax packets Syntax send-ring Undo send-ring Send-ringShutdown voice entity view View Voice entity view Example # Change the status of voice entity 4 to Down Shutdown voice subscriber line viewSilence-th-span Undo silence-th-span Slic-gain 0 Slic-gainSubscriber-line Undo slic-gain Syntax timer dial-interval seconds Undo timer dial-interval Timer dial-interval2611 Timer hookoff-interval Timer first-dialSyntax timer first-dial seconds Undo timer first-dial Related command hookoff-mode Timer ring-backTimer wait-digit Syntax timer ring-back seconds Undo timer ring-back Transmit gain Related command receive gain and subscriber-lineSyntax transmit gain value Undo transmit gain Syntax tunnel-on Undo tunnel-on Example # Enable the tunnel function for VoIP voice entityTunnel-on View VoIP entity view Undo type Related command cng-onVad-on Syntax vad-on Undo vi-card busy-tone-detect custom index Vi-card busy-tone-detect2617 Vi-card cptone-custom Syntax vi-card reboot slot-number Vi-card reboot2619 Example # Reset the voice card of slot Voice-setupVoip called-tunnel enable Syntax voice-setup Voip called-start Voip timerFast-connect Dscp values Vqa dscpCs7, or ef Keyword Dscp value in binary Dscp value in decimal View Voice view Parameter By default, DSP buffered data is not monitoredVqa dsp-monitor buffer-time Range 180 to Voip Configuration Commands Dial Plan Configuration Commands Caller-permit Dial-prefix Related command match-templateonSyntax dial-prefix string Undo dial-prefix Example # Specify 0 as a prefix Related command match-templateon page 2599 and send-numberDisplay voice number-substitute Syntax display voice number-substitute list-tag Dot-match end-only left-right right-left Related command number-substituteDot-match Undo dot-match Syntax first-rule rule-number Undo first-rule First-ruleMax-call in voice dial program view Undo max-call set-numberI all Max-call in voice entity view Related command max-call in voice entity viewUndo max-call Example # Configure the longest-number match policy Related command max-call in voice dial program viewRelated command match-templateon page 2599 and terminator Number-match Number-priority Related command rule and substitute voice dial program viewNumber-substitute Undo priority PriorityPrivate-line Syntax private-line string Undo private-line Rule Undo rule rule-tag all Meanings of characters in the string argument 2635 Number type Description Input number typeNumbering plan Description Output numbering plan Input numbering plan2637 Select-rule rule-order Undo select-rule rule-order 2639 Select-rule search-stopMeanings of integers Integer Meaning Description Undo select-rule type-first Select-rule type-firstMeanings of values Syntax select-stop Undo select-stop Select-stop2641 Related command dot-matchand match-templateon Send-number Substitute called calling list-number Related command number-substituteand ruleSubstitute subscriber line view/voice entity view Undo substitute called calling Number-substitute and rule Substitute voice dial program viewAll To Pstn are outgoing calls Syntax terminator character Undo terminator Related command match-templateon page 2599 and timerTerminator Example # Specify the pound sign # as the dial terminator Dial Plan Configuration Commands Ani all ka E1 and T1 Configuration CommandsAni Undo ani Syntax answer enable Undo answer enable Answer enableRelated command cas, timer, reverse, and renew Ani-offset Cas Related command re-answer enable and timer dl re-answerCallmode Callmode segment terminal Clear-forward-ack enable Example # Enter the R2 CAS view of TS group Display voice subscriber line Related command mode2651 Dl-bits CNG/CED Signal Default rx-bits Abcd Default tx-bits Abcd Default values of signals in R2 digital line signaling2653 Syntax dtmf enable Undo dtmf enable Dtmf enableRelated command seizure-ack enable and answer enable Related command timer dtmf Related command register-valuedigital-end Final-callednum enableSyntax final-callednum enable Undo final-callednum enable 2655 Syntax force-metering enable Undo force-metering enable Force-metering enableGroup-b enable Syntax group-b enable Undo group-b enable Related command register-valuereq-switch-groupb 2657 Syntax mode zone-name default-standard Undo mode Mode Pcm Related command register-valueand force-metering enableExample # Adopt Hongkong default R2 signaling Syntax pcm a-law µ-law Undo pcm Pri-set Example # Adopt µ-law companding for signal quantizationSyntax pri-set timeslot-list range Undo pri-set Related command answer enable and timer dl re-answer Re-answer enableSyntax re-answer enable Undo re-answer enable 2661 Demand-refused digit-end nullnum req-billingcategory Req-callednum-and-switchgroupa req-callingcategory reqChangeover to Group a signal value, in the range 1 to Subscriber-busy subscriber-charge subscriber-idle 2663 Syntax renew Abcd Related command group-b enableRenew Undo renew Related command cas and renew Seizure-ack enableRelated command cas and reverse Reverse View CAS view Related command timer dl seizureSelect-mode Timeslots Related command timer ring Sendring ringbusy enableRelated command cas and trunk-direction 2667 Special-character Signal-valueRelated command Subscriber line Example Syntax special-character character number Different signal values Undo special-character character number Example # Enter the view of voice subscriber line 1/015 Related command timeslot-setand pri-setTdm-clock Syntax tdm-clock internal line primary Undo tdm-clock View R2 CAS view Timer dlRelease-guard 2671 Timer dtmf Syntax timer dtmf time Undo timer dtmf Timer register-pulse persistence time Timer register-pulse persistenceRelated command dtmf enable Undo timer register-pulse persistence Timer register-complete group-b time Timer register-complete group-bRelated command timer register-completegroup-b Undo timer register-complete group-b Undo timer ring ringback ringbusy Timer ringTimer ring ringback ringbusy time Timeslot-set Related command subscriber line and cas Trunk-direction CAS view Related command cas and select-modeTs block open query reset timeslots timeslots-list 2677 Related command cas FAX Over IP Configuration Commands Default entity fax Example # Set the maximum fax rate to 9,600 bps globally Display voice faxSyntax display voice fax statistics 2681 Waitdpbegdemodulatetimeout FaxvofrstandardswitchFAXVOFRFRF11SWITCH Waitdpbegmodulatetimeout Fax baudrate Fax baudrate 2400 4800 9600 14400 disable voiceUndo fax baudrate Syntax fax ecm Fax ecmUndo fax ecm Syntax fax level level Undo fax level Fax levelFax local-train threshold 2685 Fax nsf-on Example # Configure the fax local training threshold toExample # Configure NSF for fax signal transmission Syntax fax nsf-on Undo fax nsf-on Fax protocol pcm g711alaw g711 μlaw Fax protocolUndo fax protocol Fax train-mode local ppp VoFR entities only support the PPP training modeFax train-mode Undo fax train-mode Voip h323-conf tcs-t38 Reset voice fax statisticsReset voice fax statistics Voip h323-conf tcs-t38 FAX Over IP Configuration Commands Display voice gateway Related command match-templateon page 2599, entity on177 Syntax area-id string Undo area-id string Syntax gk-client Gk-clientGkid Example # Enter gatekeeper client view Related command gk-idGk-2nd-id Undo gk-2nd-id Syntax gk-security call enable Undo gk-security call enable Gk-security call enableRelated command area-id,gw-id,gk-2nd-id,gw-address,ras-on Gk-id Gw-address Gk-security register-pwd cipher simple passwordGk-security register-pwd Undo gk-security register-pwd Undo gw-address Gw-idUndo gw-id Voip h323-descriptor Related command gw-id,gw-address, and gk-idRas-on Syntax ras-on 323 Configuration Commands Display voice sip call-statistics SIP Configuration Commands178 Syntax display voice sip call-statistics TPT Message Display voice sip register-state Display voice sip register-stateOutband sip Syntax outband sip Undo outband Undo proxy ipv4 Default port number isProxy SIP client view Undo register-enable Register-enableRegister-enable off on Registrar ipv4 Sip-comp Reset voice sipSip Syntax sip SIP client view Sip-comp agentUndo sip-comp callee from SIP request messages Undo sip-comp server Sip-comp serverSip-domain View SIP client view Syntax source-ip ip-address Undo source-ip Source-ip2707 SIP Configuration Commands Example # Enable fuzzy telephone number registration Wildcard-register enableSyntax wildcard-register enable Undo wildcard-register 2709 SIP Configuration Commands Address Vofr Configuration Commands179 Undo address vofr-dynamic vofr-static Call-mode Related command Trunk-idand address ExampleCid select-mode Display fr vofr-info Related command Vofr Example# Set the CID selection mode to min-poll on Dlci Interface Dlci view Undo entity entity-number vofr Entity vofrOutband vofr Outband vofr Seq-number Seq-numberUndo seq-number Timestamp Related command call-modeTrunk-id View Interface Dlci view Voice bandwidthVofr 2717 Related command call-mode Undo vofr frf11-timer Vofr frf11-timerVofr frf11-timer time Hang up successfully in the FRF.11 trunk mode Vofr Configuration Commands Accounting Voice Radius Configuration CommandsAaa-client Syntax aaa-client Syntax accounting-did Undo accounting-did Related command acct-methodand accountingAccounting-did View Voice AAA client view Acct-method Related command accounting and accounting-did# Restore the default accounting method Example # Set the accounting method to start-ack Syntax authentication Undo authentication AuthenticationAuthentication-did Related command gw-access-numberand authorization Syntax authorization Undo authorization AuthorizationRelated command authorization-did 2725 Syntax authorization-did Undo authorization-did Authorization-didRelated command gw-access-numberand authentication Related command authentication-did Callednumber receive-method Related command gw-access-number2727 Cdr Related command gw-access-numberand process-configCard-digit Syntax card-digit card-digit Undo card-digit Undo cdr all buffer duration threshold Related command display voice call-history-record# Set the alarm threshold for CDRs to 10% Example # Set the number of CDRs that can be saved to Display voice access-number Display voice access-numberGw-access-number and aaa-client 2731 Display voice call-history-record Example # Display call records by calling number Related command cdr2733 Display voice radius statistic Syntax display voice radius statistic VORDS=AAA Related command reset voice radius statistic2735 AAA=VORDS Gw-access-number CMC=VORDS # Delete the access number Password-digit# Add the access number 179 and enter access number view # Delete all access numbers Process-config # Restore the default dialing process for the access number 2739 Redialtimes Undo redialtimes Selectlanguage Reset voice radius statisticGw-access-numberand process-config Display voice radius statistic Voice Radius Configuration Commands