VC-3 | 3Com MSR 30, MSR 50 instruction

676CHAPTER 45: CPOS INTERFACE CONFIGURATION COMMANDS

Different from the display controller cpos command, this command can display the error and alarm information of lower-order paths and T1 frames.

Example # Display the status information of T1 channel 2 on interface CPOS 4/0.

<Sysname> display controller		cpos 4/0 t1 2
Cpos4/0 current state : UP		Frame-format SDH, multiplex AU-3, clock
master, loopback not set
Tx: J0: 0x01, J1: "NetEngine", C2: 0x02
Rx: J0: 0x01, J1: "NetEngine", C2: 0x02
Regenerator section:
Alarm: none
Error:	0 BIP, 0 SEF
Multiplex section:
Alarm: none
Error:	0 BIP, 0 REI
Higher order path(VC-3-2):
Alarm: none
Error:	0 BIP, 0 REI
Lower order path:
Alarm: none
Error:	4095 BIP, 2047 REI
Cpos4/0	CT1 2 is up
Frame-format ESF, clock master, loopback not set
T1 framer(2-1-1):
Alarm: none
Error:	4095 FERR, 79 AERR
Table 123 Description on the fields of the display controller cpos t1 command

Field	Description

Cpos4/0 current state

Frame-format SDH, multiplex AU-3, clock master, loopback not set

The current physical state of the CPOS interface

Physical layer information of the CPOS interface: the framing format is set to SDH, AU-3 path is adopted, master clock (internal clock signal) is used, and loopback is disabled.

Tx: J0: 0x01, J1: “NetEngine”,	The sent overhead bytes.
C2: 0x02
Rx: J0: 0x01, J1: “NetEngine”,	The received overhead bytes.
C2: 0x02
Regenerator section	Alarms and errors about the regeneration section.
Multiplex section	Alarms and errors about the regeneration section.
Higher order path(VC-3-2)	Alarm and error statistics about the higher-order path to
	which the T1 channel belongs. VC-3-2 means the second
	VC-3.
Lower order path	Alarm and error statistics about the lower-order path.
Error	Error statistics.
Cpos4/0 CT1 2 is up	The current physical state of T1 channel 2 on interface
	CPOS 4/0.
Frame-format ESF, clock master,	Information about the physical layer of the T1 channel: the
loopback not set	framing format is set to ESF, master clock (internal clock
	signal) is used, loopback is disabled.

Page 676

Image 676

Contents

H3C MSR 20/30/50 Series Routers 3Com Corporation Campus Drive Marlborough, MA USA United States Government Legend Contents POS Interface Configuration Commands Adsl Interface Configuration CommandsGeneral Ethernet Interface Configuration Commands Fundamental Serial Interface Configuration Commands Fundamental CE1/PRI Interface Configuration Commands Fundamental CT1/PRI Interface Configuration Commands 14 E1-F Interface Configuration Commands Fundamental CE3 Interface Configuration Commands 15 T1-F Interface Configuration CommandsFundamental CT3 Interface Configuration Commands ATM Configuration Commands Isdn BRI Interface Configuration CommandsDCC Configuration Commands Basic Dlsw Configuration Commands 340 Frame Relay Configuration Commands Garp Configuration Commands Gvrp Configuration CommandsHdlc Configuration Commands Lapb and X.25 Configuration Commands 451 X25 pvc X25 queue-length 453 X25 receive-threshold 454 425 Display x25 hunt-group-info Display x25 map 426455 Link Aggregation Configuration Commands Link Aggregation Debugging CommandsModem Configuration Commands Port Mirroring Configuration Commands Pppoe Server Configuration Commands PPP Link Efficiency Mechanism Configuration CommandsPppoe Client Configuration Commands PPP Debugging Commands Bridging Configuration CommandsIsdn Configuration Commands Debugging ppp Mstp Configuration Commands Vlan Configuration Commands PORT-BASEDVLAN Configuration CommandsVoice Vlan Configuration Commands Port Isolation Configuration Commands Cpos Interface Configuration Commands ARP Configuration Commands Gratuitous ARP Configuration Commands ARP Source Suppression Configuration CommandsAuthorized ARP Configuration Commands Proxy ARP Configuration Commands Dhcp Relay Agent Configuration Commands Dhcp Client Configuration CommandsDhcp Snooping Configuration Commands Bootp Client Configuration Commands DNS Configuration Commands IP Accounting Configuration CommandsIP Addressing Configuration Commands IP Performance Configuration Commands IP Unicast Policy Routing Configuration Commands UDP Helper Configuration CommandsUrpf Configuration Commands Fast Forwarding Commands NAT-PT Configuration Commands 840 Display tcp ipv6 status 842Display natpt address-group 863 Display natpt aging-time 864 display natpt all Tunneling Configuration Commands Dual Stack Configuration Commands69 IPV6 Unicast Policy Routing Configuration Commands Terminal Access Configuration Commands IP Routing Table Commands BGP Configuration Commands Ebgp-interface-sensitive 977981 Log-peer-change 983 Peer advertise-communityBGP/BGP-VPN instance view BGP Debugging Commands IS-IS Configuration Commands IS-IS Debugging Commands Ospf Configuration Commands 1155 Snmp-agent trap enable ospf 11171128 1140 Routing Policy Common Configuration Commands RIP Configuration Commands1179 79 IPV4 Routing Policy Configuration Commands 80 IPV6 Routing Policy Configuration CommandsStatic Routing Configuration Commands 82 IPV6 BGP Configuration Commands 1243 12231246 83 IPV6 IS-IS Configuration Commands 84 IPV6 OSPFV3 Configuration Commands 85 IPV6 Ripng Configuration Commands 86 IPV6 Static Routing Configuration CommandsMulticast Routing and Forwarding Configuration Commands Delete ipv6 static-routes all 1325 ipv6 route-static Igmp Configuration Commands Msdp Configuration CommandsCache-sa-enable 1365 display msdp brief 1366 PIM Configuration Commands 1376 1422 14211429 93 IPV6 PIM Configuration Commands MLD Configuration Commands1451 Multicast VPN Configuration Commands 1495Display multicast-domain vpn-instance share-group 1505 Mpls Basics Configuration Commands Mpls TE Configuration Commands Mpls rsvp-te reliability 1610 Mpls rsvp-te resvconfirm 1611 Mpls L2VPN Configuration Commands Mpls L3VPN Configuration Commands VAM Server Configuration Commands 1697 VAM Client Configuration Commands Ipsec Profile Configuration CommandsDvpn Tunnel Configuration Commands GRE Configuration Commands Traffic Policing TP Configuration Commands Traffic Shaping Configuration CommandsLine Rate Configuration Commands Defining Class Commands Fifo Queuing Configuration Commands PQ Configuration CommandsCQ Configuration Commands WFQ Configuration Commands QOS Token Configuration Commands Priority Mapping Table Configuration CommandsPort Priority Configuration Commands Port Priority Trust Mode Configuration Commands FR QOS Configuration Commands 126 802.1X Configuration CommandsAAA Configuration Commands access-limit Reset dar session 1927 Radius Configuration Commands1958 Hwtacacs Configuration Commands Packet Filter Firewall Configuration Commands MAC Authentication Configuration Commands Aspf Configuration Commands aging-timeNAT Configuration Commands PKI Configuration Commands Portal Configuration Commands RSH Configuration Commands rshCommon Configuration Commands 138 IPV4 ACL Configuration Commands Ipsec Configuration Commands IKE Configuration Commands 142 SSH2.0 Configuration Commands Sftp Configuration Commands bye SSL Configuration Commands Backup Center Configuration Commands 146 IPV4-BASEDVRRP Configuration CommandsVrrp Configuration Commands for IPV6 Device Management Commands NQA Client Configuration Commands Temperature-alarm enable 2263 Temperature-limit2262 2276 NQA Server Configuration Commands Netstream Configuration CommandsNTP Configuration Commands Rmon Configuration Commands Snmp Configuration Commands File System Configuration Commands cd Configuration File Management Commands FTP Server Configuration CommandsFTP Client Configuration Commands ascii Tftp Client Configuration Commands System Maintaining Commands System Debugging CommandsBasic Configuration Commands Information Center Configuration Commands User Interface Configuration Commands 2460 POE Configuration Commands MAC Address Table Management Configuration CommandsOAP Module Configuration Commands Acfp Configuration Commands Acsei Server Configuration CommandsAcsei Client Configuration Commands Track Configuration Commands Voip Configuration Commands address 2551 Reset ipx routing-table statistics protocol2546 Area 2554 area-id 2592 Dial Plan Configuration Commands 175 E1 and T1 Configuration Commands aniCaller-permit 2639 177 H.323 Configuration Commands FAX Over IP Configuration CommandsSIP Configuration Commands Vofr Configuration Commands Voice Radius Configuration Commands aaa-client2716 2734 About this Guide Lists icon conventions that are used throughout this guideLists text conventions that are used throughout this guide Text Conventions Related Documentation Alphabetical Listing of Commands Area Ospf view 1108 area OSPFv3 viewPage Page Rp IPv6 PIM view 1464 c-rp PIM view Page Display bgp vpnv4 vpn-instancerouting-table Page Display ipv6 policy-based-route statistics Page Page Page Page Page Fr compression frf9 385 fr compression iphc Page Igmp last-member-query-interval Ipv6 nd autoconfig managed-address-flag Page Page Page Mpls te resv-style 1631 mpls te retry 2308 Peer keep-all-routesBGP/BGP-VPN instance view Peer ebgp-max-hopBGP/BGP-VPN instance viewPeer allow-as-loopBGP/BGP-VPN instance view Peer next-hop-localBGP/BGP-VPN instance view Peer preferred-valueBGP/BGP-VPN instance viewPeer next-hop-invariableBGP-VPNv4 subaddress family view Peer public-as-onlyBGP/BGP-VPN instance view Pppoe-servermax-sessionsremote-mac Primary accounting Hwtacacs scheme view Qos wred ip-precedence 1850 qos wred queue table Reset aspf session 2007 reset atm interface 112 reset bgp Reset pim ipv6 control-message counters Page Page Ssl client-policy 2215 ssl server-policy Statistics interval 1562 step for IPv4 2100 step for IPv6Page Page Page X29 timer inviteclear-time Page Display interface atm Public ATM and DSL Interface CommandsSyntax display interface atm interface-number Syntax reset atm interface atm interface-number Reset atm interfaceInterface atm Cable Configuration CommandsClock Code Code ami hdb3Code ami b8zs Undo code Differential-delay Display interface ima-groupSyntax display interface ima-group group-interfacenumber 115 Frame-format View ATM E1/T1 interface view ParameterATM direct mapping CRC4 ADM ESF ADM Frame-length Ima ima-groupSyntax frame-length 32 64 128 Undo frame-length Syntax ima ima-group group-number Undo ima ima-group Example # Add the link of ATM E1 interface 5/0 to IMA group Ima-clockSyntax ima-clock ctc link-number number itc Undo ima-clock Ima-standard Ima-testIma-test link-number number pattern-id id Undo ima-test By default, IMA group interface test is disabled Interface ima-groupLoopback Syntax loopback cell local payload remote Undo loopback Min-active-links ScrambleSyntax min-active-links number Undo min-active-links Syntax scramble Undo scramble Parameter None Syntax cable long short Undo cable Slave Sets the clock mode as slaveView ATM E3/T3 interface view Frame-format g751-adm g751-plcp g832-adm Frame-format cbit-adm cbit-plcp m23-adm m23-plcp Loopback cell local payload remote ATM E3/T3 Interface Configuration Commands Frame-format sdh sonet Loopback cell local remote View ATM OC-3c interface view, STM-1 interface view 129 ATM OC-3C/STM-1 Interface Configuration Commands Shdsl Interface Configuration Commands ActivateSyntax activate Undo activate View ATM G.SHDSL interface view Display dsl configuration Field Description Syntax display dsl status interface atm interface-number Display dsl status133 Gspn Description on the fields of the display dsl status command 135 Syntax display dsl version interface atm interface-number Display dsl versionITU G991.2 Annex A, ITU Shdsl mode Shdsl annex Example # Set the operating mode of interface ATM 5/0 to CO Shdsl psdShdsl rate Syntax shdsl psd asymmetry symmetry Undo shdsl psd Single-pair interface rate to auto mode Kbps four-wire G.SHDSL interface rate is 4,624 kbps# Configure ATM 5/0 to operate in the auto-negotiation mode Use the undo shdsl snr-margincommand to restore the default Shdsl wire 2 4-auto-enhanced 4-enhanced 4-standard Shdsl wireUndo shdsl wire 141 Shdsl Interface Configuration Commands View ATM Adsl interface view Adsl Interface Configuration CommandsExample # Activate Adsl interface 2/0 Adsl standard Adsl tx-attenuationAdsl standard auto g9923 g9925 gdmt glite t1413 Undo adsl standard Bootrom update file 145 Display dsl configuration 147 LS0US FieldDescription Dslam 149 Bdcm Adsl Interface Configuration Commands Crc POS Interface Configuration CommandsSyntax crc 16 Undo crc Display interface pos Syntax display interface pos interface-number 153 LCP opened, Ipcp opened, IP6CP opened Display ip interface pos Display ipv6 interface posDisplay ip interface pos interface-number Syntax display ipv6 interface pos interface-number Flag Example # Set the SDH overhead byte J0 of POS1/0 interface Related command display interface pos# Set the framing format on interface POS 1/0 to SDH Link-protocol Loopback local remoteLocal Internal loopback Remote External loopback Mtu That the state of the link layer protocol is reported upInterfaces cannot be connected successfully Syntax mtu size Example # Enable payload scrambling on interface POS 1/0 ThresholdSyntax threshold sd sf value Undo threshold sd sf 159 Example # Set the SD threshold to 10e-4 for POS 1/0 General Ethernet Interface Configuration Commands Combo enableRelated command display port combo and shutdown Description Special characters used in regular expressions Display brief interfaceCharacter Meaning Example # Display brief information of interfaces Related command interface163 Display interface Acronyms for different types of InterfacePvid Interface name Acronyms 165 Field Output queue Fifo queuing 167 Related command speed DuplexFlow-control Syntax duplex auto full half Undo duplex Interface Can be represented as 1/0E1/0 Syntax loopback external internal Undo loopback Support for these two commands varies with device models Port link-modePort link-mode bridge route Undo port link-mode Reset counters interface Example # Configure Ethernet1/0 to work in bridge modeView User view 171 Shutdown Speed Related command duplex 173 General Ethernet Interface Configuration Commands Broadcast-suppression Display loopback-detection Display portSyntax display loopback-detection Display port hybrid trunk Display port-group manual all name port-group-name Display port-group manualExamples Flow-interval Group-memberSyntax flow-interval interval Undo flow-interval Undo group-member interface-list Loopback-detection control enable 179 Loopback-detection enable Related command loopback-detection control enableLoopback-detection interval-time View System view/Ethernet interface view Related command display loopback-detection Loopback-detection per-vlan enable181 Optical port of a Combo port does not support this command MdiMulticast-suppression Mdi across auto normal Port-group manual port-group-name aggregation agg-id Port-groupUndo port-group manual port-group-name Currently, these two commands are not supported Unicast-suppressionVirtual-cable-test Syntax virtual-cable-test 185 Page Example # Configure MTU for Ethernet1/0 to be 1,000 bytes Timer holdSyntax timer hold seconds Undo timer hold Configuration Commands for Ethernet Interfaces in Route Mode Fundamental Serial Interface Configuration Commands Async modeSyntax async mode flow protocol Undo async mode Baudrate Clock serial interface view Undo baudrateClock dteclk1 dteclk2 dteclk3 dteclk4 dteclkauto View Serial interface view 191 Dteclk1Clock selection option Description Code nrzi Country-codeSyntax code nrzi Undo code View Synchronous serial interface view Example # Configure to adopt 32-bit CRC DetectSyntax crc 16 32 none Undo crc Asynchronous serial interface detect dsr-dtr Syntax eliminate-pulse Undo eliminate-pulse Eliminate-pulseView Asynchronous serial interface view Idle-mark Invert receive-clockSyntax idle-mark Undo idle-mark Syntax invert receive-clock Undo invert receive-clock Invert transmit-clock Syntax invert transmit-clock Undo invert transmit-clock Syntax loopback Undo loopback Mtu on serial interfaces197 Physical-mode Phy-mruSyntax physical-mode async sync Syntax phy-mru size Undo phy-mru Syntax reverse-rts Undo reverse-rts Reverse-rts199 Virtualbaudrate Virtualbaudrate virtualbaudrateUndo virtualbaudrate Baudrate Fundamental CE1/PRI Interface Configuration Commands Channel-set CE1/PRI interface view Clock CE1/PRI interface view Clock Controller e1 Code CEI/PRI interface viewController e1 number Crc 16 32 none Detect-aisSyntax detect-ais Undo detect-ais Description on the fields of the command Display controller e1Syntax display controller e1 interface-number 205 Error-diffusion restraint config Undo error-diffusion restraint config Error-diffusion restraint enable Error-diffusion restraint restart-channelBy default, error packets diffusion restraint is enabled Example # Enable error packets diffusion restraint Idlecode CE1/PRI interface view Frame-format CE1/PRI interface viewTwo types of line idle code are available 0x7E and 0xFF Itf number number type 7e ff Itf CE1/PRI interface viewUndo itf type number Loopback CE1/PRI interface view Pri-set CE1/PRI interface viewLoopback local payload remote Pri-set timeslot-list list Reset counters controller e1 Reset counters controller e1 interface-numberCommand Display controller e1 interface-number command Using ce1 e1 Using CE1/PRI interface viewUndo using Fundamental CT1/PRI Interface Configuration Commands Alarm-thresholdLevel-2 Level-2 , level-3 , and level-4 Bert CT1/PRI interface view Bert pattern 215 220 time minutes unframedUndo bert Ranges from 1 to 1,440 Channel-set CT1/PRI interface view Cable CT1/PRI interface view655ft Clock CT1/PRI interface view View CT1/PRI interface view Code CT1/PRI interface view Controller t1Ami Adopts AMI line code format # Set the line code format of the interface T1 2/0 to AMI Data-coding inverted normal Data-coding CT1/PRI interface viewUndo data-coding Syntax display controller t1 interface-number Display controller t1219 Clock or slave for the line clock 221 Error-diffusion restraint config Example # Enable error packet diffusion restraint By default, the function is disabled223 Support of this command varies with device model Error packet diffusion restraint functionFdl Set-number argument is a channel set number Idlecode CT1/PRI interface view Frame-format CT1/PRI interface viewFrame-format esf sf Itf CT1/PRI interface view Loopback CT1/PRI interface viewSyntax itf number number type 7e ff Undo itf number type Syntax loopback local payload remote Remote Enables the interface to perform remote loopback # Enabled remote loopback on interface T1 2/0Pri-set CT1/PRI interface view Loopback on the CT1/PRI interface Reset counters controller t1 Reset counters controller t1 interface-numberFor a CT1/PRI interface # Clear the controller counter for CT1/PRI interface T1 2/0 Sendloopcode 229 Fundamental CT1/PRI Interface Configuration Commands Display fe1 E1-F Interface Configuration CommandsDisplay fe1 serial interface-number Fe1 cable Fe1 clockFe1 cable long short Undo fe1 cable Fe1 code Fe1 detect-ais Fe1 frame-format Fe1 loopback Local Sets the interface in internal loopback mode Fe1 timeslot-listUndo fe1 loopback Syntax fe1 timeslot-list list Undo fe1 timeslot-list Related command fe1 unframed Fe1 idlecodeFe1 itf Syntax fe1 idlecode 7e ff Undo fe1 idlecode Fe1 unframed Fe1 unframedUndo fe1 unframed Related command fe1 timeslot-list Display ft1 T1-F Interface Configuration CommandsDisplay ft1 serial interface-number Description on the fields of the display ft1 serial command 241 Bert statestopped, not completed Ft1 bert T1-F interface view Ft1 bert pattern 215 220 time minutes unframedUndo ft1 bert T1-F interface view Ft1 cable Syntax ft1 cable long decibel short length Undo ft1 cableView T1-F interface view 243 Ft1 clock Ft1 codeFt1 clock master slave Undo ft1 clock Ft1 data-coding inverted normal Ft1 data-codingUndo ft1 data-coding Ft1 fdl Ft1 frame-format Ft1 idlecode Ft1 itfFt1 idlecode 7e ff Undo ft1 idlecode Use the undo ft1 loopback command to restore the default Ft1 loopbackFt1 loopback local payload remote Undo ft1 loopback Ft1 timeslot-list # Set T1-F interface Serial 2/0 in local loopback mode249 Undo ft1 alarm-threshold Ft1 alarm-thresholdOn the T1-F interface Ft1 sendloopcode 251 T1-F Interface Configuration Commands Bert CE3 Interface Fundamental CE3 Interface Configuration CommandsBert pattern 27 211 215 qrss time number unframed Clock CE3 interface view Controller e3Display controller e3 Example # Enter the view of interface E3 2/0 Syntax display controller e3 interface-number Display controller e3255 Fundamental CE3 Interface Configuration Commands E1 bert 257 Related command e1 unframed E1 channel-setE1 set clock Syntax e1 line-numberset clock master slave E1 set frame-format Undo e1 line-numberset clockView CE3 interface view 259 E1 shutdown E1 set loopbackUndo e1 line-numbershutdown Related command e1 channel-set E1 unframedFe3 Undo e1 line-numberunframed CE3 interface in FE3 mode view Set the DSU mode or the subrateUse the undo fe3 command to restore the default These two commands are only available in E3 mode Loopback CE3 interface view National-bitNational-bit 0 Undo national-bit Using CE3 interface view Related command controller e3Syntax using ce3 e3 Undo using Example # Set the national bit to 0 on interface E3 2/0 Fundamental CT3 Interface Configuration Commands Alarm CT3 interface viewAlarm detect generate ais febe idle rai Undo alarm detect generate ais febe idle rai # Enable CT3 interface T3 2/0 to send AIS alarm signals Bert CT3 interface view Cable CT3 interface view Clock CT3 interface viewSyntax cable feet 267 Related command display controller t3 Controller t3Example # Enter the view of interface T3 2/0 None Adopts no CRC Syntax display controller t3 interface-number Display controller t3269 AIS Configurable and default to line 271 LOS, LOF, AIS, or RAI Feac CT3 interface view Ft3 Frame-format CT3 interface viewFrame-format c-bit m23 275 Loopback CT3 interface view Mdl CT3 interface view 277 # Set LIC to hello for CT3 interface T3 2/0 T1 alarm# Send path messages on CT3 interface T3 2/0 T1 bert 279 Related command t1 unframed T1 channel-set T1 sendloopcode 281 T1 set clock T1 set frame-format T1 set loopback T1 set fdlView CT3 interface view 283 T1 show T1 shutdown Description on the fields of the t1 show command285 Related command t1 channel-set T1 unframedUndo t1 line-numbershutdown Syntax t1 line-numberunframed undo t1 line-numberunframed Using CT3 interface view Using ct3 t3Ct3 Sets the CT3 interface to operate in channelized mode T3 Sets the CT3 interface to operate in unchannelized mode Fundamental CT3 Interface Configuration Commands Isdn BRI Interface Configuration Commands Loopback Isdn BRI interface viewLoopback b1 b2 both Fixed Isdn interfaces on your router, if there is any Isdn BRI Interface Configuration Commands ATM Configuration Commands Related command atm-classAtm class Atm-class Related command atm class Atm-link checkSyntax atm-link check Undo atm-link check View ATM P2P sub-interface view Display atm class Related command Display atm interface ExampleDisplay atm class atm-class-name Display atm interface Syntax display atm interface atm interface-number Display atm map-info 295 Display atm pvc-group VPI/VCIPVC-NAME State Display atm pvc-info 297 Syntax encapsulation aal5-encap Undo encapsulation EncapsulationIndex Example # Enter Atm1/0 interface Ip-precedence299 Map bridge Related command pvc-group,pvcView PVC view/ATM Class view # Configure an IP address 10.1.1.1/16 for the VE interface Map ip# Create PVC 1/102 on the ATM interface Atm2/0 Map ip inarp minutes broadcast Undo map ip inarp Map ppp Syntax map ppp virtual-template vt-number Undo map ppp # Create PVC 1/101 on interface Atm1/0 # Create a PPPoA map using the VT interface created303 Oam ais-rdi Undo oam frequency Oam frequency305 Oamping interface Pvc Related command display atm pvc-info,pvc max-number VCI range for each type of ATM interface307 Interface type Related command ip-precedence,pvc Pvc-groupPvc max-number Syntax pvc max-number max-number Undo pvc max-number Pvp limit Undo pvp limit vpi Example # Set the traffic of VP with vpi 1 to 2M Service cbrInterface type Value range of output-pcr Service ubr Service vbr-nrtRelated command service vbr-nrt,service vbr-rt,service ubr Syntax service ubr output-pcr Service vbr-rt Related command service ubr, service vbr-rt, and service cbr # Bring up ATM 5/0 Parameters None313 Transmit-priority Syntax transmit-priority value Undo transmit-priority DCC Configuration Commands Related command dialer bundle-memberDialer bundle Dialer bundle-member Related command dialer bundle Dialer callback-center Dialer call-in 317 Related command interface dialer Related command dialer callback-centerDialer circular-group Dialer enable-circular Dialer enable-circularUndo dialer enable-circular Bundle-member command Related command dialer circular-group Related command dialer thresholdDialer flow-interval Dialer isdn-leased physical interface view Syntax dialer number dial-number Undo dialer number Dialer number321 Related command dialer route Dialer priorityDialer queue-length Syntax dialer priority priority Undo dialer priority Dialer route 323 Dialer threshold Related command dialer flow-interval Dialer timer autodial325 Dialer timer compete Dialer timer enable Dialer timer idleSyntax dialer timer enable seconds Undo dialer timer enable Syntax dialer timer idle seconds Undo dialer timer idle Dialer user Dialer timer wait-carrierSyntax dialer user username Undo dialer user Dialer-group Example # Add a remote username routerbSyntax dialer-group group-number Undo dialer-group 329 Related command dialer-rule Example # Add interface Serial 2/0 to dialer access groupDialer-rule Undo dialer-rule group-number Related command dialer-group Display dialerAny view Number Display interface dialer Display interface dialer numberNumber Dialer interface number Information about all the dialer interfaces Syntax interface dialer number Undo interface dialer number Interface dialer333 Ppp callback Ppp callback ntstringPpp callback client server Undo ppp callback client server Undo ppp callback ntstring Related command ppp callback335 DCC Configuration Commands Basic Dlsw Configuration Commands Example # Configure Serial 1/0 to use Nrzi encodingDisplay dlsw circuits Syntax display dlsw circuits circuit-id verbose Display dlsw information Display dlsw information local ip-address Display dlsw remote # Display the local information about capabilities exchangeSyntax display dlsw remote ip-address 339 Display dlsw reachable-cache Display dlsw reachable-cacheInformation of DLSw # Display the reachability information of DLSw Description on the fields of the display llc2 command Display llc2Syntax display llc2 circuit circuit-id 341 Syntax dlsw enable Undo dlsw enable Dlsw enableDlsw bridge-set Dlsw ethernet-frame-filter # Enable DLSw343 Dlsw local Dlsw reachable # Allow the router to access SAP addresses 12345 # Permit access to user-configured MAC addresses only Dlsw reachable-cacheDlsw remote Undo dlsw remote ip-address 347 Related command sdlc mac-map remote Dlsw reverseDlsw max-transmission Syntax dlsw reverse mac-address Undo dlsw multicast Dlsw multicast349 Dlsw timer Syntax link-protocol sdlc Link-protocol sdlc351 Llc2 max-ack Llc2 max-pduSyntax llc2 max-ack length Undo llc2 max-ack Syntax llc2 max-pdu length Undo llc2 max-pdu Llc2 max-send-queue Llc2 max-transmissionSyntax llc2 max-send-queue length Undo llc2 max-send-queue 353 Llc2 modulo Llc2 receive-windowLlc2 modulo 8 Undo llc2 modulo Llc2 timer ack Llc2 timer ack-delaySyntax llc2 timer ack mseconds Undo llc2 timer ack 355 Llc2 timer busy Llc2 timer detectSyntax llc2 timer busy mseconds Undo llc2 timer busy Syntax llc2 timer detect mseconds Undo llc2 timer detect Syntax llc2 timer poll mseconds Undo llc2 timer poll Llc2 timer poll357 Reset dlsw circuits Llc2 timer rejectReset dlsw reachable-cache Reset dlsw tcp Syntax reset dlsw tcp ip-addressDescription on the fields of the reset dlsw tcp command 359 Sdlc controller Sdlc enable dlsw Syntax sdlc enable dlsw Undo sdlc enable dlswSdlc mac-map local 361 Sdlc mac-map remote Sdlc max-pdu Sdlc max-send-queueSyntax sdlc max-pdu number Undo sdlc max-pdu Syntax sdlc max-send-queue length Undo sdlc max-send-queue Sdlc max-transmission Sdlc moduloView Synchronous serial interface view Specifies the modulus value to be Sdlc sap-map local Related command sdlc sap-map remote365 Related command sdlc sap-map local Sdlc sap-map remoteSdlc simultaneous Syntax sdlc simultaneous Undo sdlc simultaneous Sdlc status primary secondary Sdlc statusUndo sdlc status primary secondary Sdlc timer lifetime Sdlc timer ackSyntax sdlc timer ack mseconds Undo sdlc timer ack Sdlc timer poll Syntax sdlc timer poll mseconds Undo sdlc timer pollSdlc window Syntax sdlc window length Undo sdlc window Sdlc xid Undo sdlc xid sdlc-address Frame Relay Configuration Commands AnnexgDisplay fr compress Annexg dce dte Display fr dlci-switch Related commands fr compression frf9 Related command fr inarp Example Display fr inarp-infoDisplay fr interface # Display statistics about frame relay Inarp packets Display fr lmi-info Range 0 to# Display information about all frame relay interfaces Frame Display fr iphc Related command fr compression iphc375 Display fr map-info Mappings or the one for the specified interfaceWhether dynamic address mapping operates normally Fr map ip , fr inarp 377 Display fr map-info pppofrDlci = 100, IP Inarp Display fr pvc-info 1007Statistics about data transmitted and received on them Fr dlci Display fr statistics 379 Display interface mfr MTU Display mfr 381 Description on the fields of the display mfr command LID Syntax display x25 template name Display x25 template383 Related command x25 template, x25-template Fr compression frf9 Fr compression iphcSyntax fr compression frf9 Undo fr compression View Subinterface point-to-point view Undo fr compression iphc Fr dlciUndo fr dlci dlci-number Fr dlci-switch Use the undo fr dlci command to cancel the configurationUndo fr dlci-switch in-dlci Related command fr switching Fr inarp Syntax fr inarp ip dlci-number Undo fr inarp ip dlci-number Syntax fr interface-type dce dte nni Undo fr interface-type Fr interface-type389 Fr iphc Fr lmi n391dteTcp-include Fr map ip , fr compression iphc Syntax fr lmi n392dce n392-value Undo fr lmi n392dce Fr lmi n392dce391 Fr lmi n392dte Syntax fr lmi n392dte n392-value Undo fr lmi n392dte Fr lmi n393dce Fr lmi n393dteSyntax fr lmi n393dce n393-value Undo fr lmi n393dce Syntax fr lmi n393dte n393-value Undo fr lmi n393dte Fr lmi t392dce Syntax fr lmi t392dce t392-value Undo fr lmi t392dce Fr lmi type ansi nonstandard q933a bi-direction Fr lmi typeUndo fr lmi type Fr map ip Fr switch Related command interface virtual-templateonUndo fr switch name Fr map ppp Fr switching Syntax fr switching Undo fr switching Interface serial Interface mfr399 Link-protocol fr Link-protocol fr ietf nonstandard Link-protocol fr mfr Mfr bundle-nameSyntax link-protocol fr mfr interface-number Syntax mfr bundle-name name Undo mfr bundle-name Mfr fragment Mfr fragment-sizeSyntax mfr fragment Undo mfr fragment Syntax mfr fragment-size bytes Undo mfr fragment-size Syntax mfr link-name name Undo mfr link-name name Mfr link-name403 Mfr stateup-respond-addlink Mfr retrySyntax mfr retry number Undo mfr retry Mfr timer ack Syntax mfr timer ack seconds Undo mfr timer ackRelated command mfr timer hello, mfr retry 405 Mfr timer hello Syntax mfr timer hello seconds Undo mfr timer helloMfr window-size Syntax mfr window-size number Undo mfr window-size Reset fr inarp View Frame relay switching viewSyntax reset fr inarp Related command fr inarp Related command fr lmi t392dce Reset fr pvcExample # Clear all the frame relay dynamic address maps X25-template X25 templateSyntax x25-template name Undo x25-template name Syntax x25 template name Undo x25 template name Frame Relay Configuration Commands Garp Configuration Commands Display garp timerSyntax display garp timer interface interface-list Display garp statistics Garp timer Related command garp timer, garp timer leaveallExample # Display Garp timers on port Ethernet 1/0 View Ethernet interface view, port group view Garp timer leaveall Related command display garp timerDependencies of Garp timers Timer Lower limit Upper limit Reset garp statistics interface interface-list Reset garp statisticsDisplay gvrp statistics Display gvrp statistics Gvrp Configuration CommandsSyntax display gvrp statistics interface interface-list Related command display gvrp status Display gvrp statusGvrp Syntax gvrp Gvrp registration Gvrp registration fixed forbidden normalUndo gvrp registration Display garp statistics Gvrp Configuration Commands Hdlc Configuration Commands Timer holdTimer hold seconds Link-protocol hdlc Hdlc Configuration Commands Channel Lapb and X.25 Configuration CommandsX25 hunt-group Lapb and X.25 Configuration Commands 423 Description on the fields of the display interface commandLapb DCE Display x25 alias-policy Related command x25 alias-policy Example Display x25 cugDisplay x25 hunt-group-info Display x25 cug local-cug local-cug-number network-cug Display x25 map Related command x25 hunt-groupSyntax display x25 map Description on the fields of the display x25 map command Display x25 padExample # Display the X.25 address mapping table Syntax display x25 pad pad-id Display x25 switch-table pvc Display x25 switch-table svcSyntax display x25 switch-table pvc Syntax display x25 switch-table svc dynamic static Related command x25 switch svc Example # Display X.25 SVC static switching tableDisplay x25 vc Syntax display x25 vc lci Data 0/0 Interrupt 0/0 431 Description on the fields of the display x25 vc commandSVC Display x25 x2t switch-table Display x25 xot Lapb max-frame Syntax lapb max-frame n1-value Undo lapb max-frame433 Difference between N1 Related command lapb window-size Lapb moduloLapb retry Parameter 8 Modulo Lapb timer Undo lapb timer t1 t2 t3Lapb window-size Syntax lapb window-size k-valueundo lapb window-size Lapb modulo Link-protocol lapbLink-protocol lapb dce dte ip multi-protocol Pad Link-protocol x25 dce dte ietf nonstandard Reset xot Reset Reset lapb statistics Syntax reset lapb statisticsTranslate ip Undo translate ip ip-addressport port-number Undo translate x25 x.121-address TranslateParameter x.121-address X.121 address X25 alias-policy 441 X25 call-facility Description on the user facility option X25 cug-service Related command x25 map, x25 modulo443 Option Description Window-size X25 default-protocol Related command x25 local-cug X25 hunt-group 445 X25 ignore called-address X25 ignore calling-address X25 local-cug 447 X25 map Related command x25 call-facility,x25 cug-serviceUndo x25 map ip compressedtcp protocol-address Send-delay delay-time 449Option Description Broadcast Protocols such as Routing Information Protocol X25 modulo Syntax x25 modulo 8 Undo x25 modulo X25 packet-size # Set the modulo on the X.25 interface Serial 2/0 toUndo x25 packet-size 451 Undo x25 pvc pvc-number X25 pvcDescription on PVC attribute option Syntax x25 queue-length queue-length Undo x25 queue-length X25 queue-length453 Related command x25 window-size X25 receive-threshold X25 response calling-address X25 response called-address455 Related command x25 map X25 reverse-charge-accept X25 switch pvc Related command x25 call-facility,x25 mapUndo x25 switch pvc pvc-number1 X25 roa-list Lapb and X.25 Configuration Commands 121 mode matching rules X25 switch svc459 Number SVC route number Input rules of X.121 address mode matching stringCharacters Input rules X25 switch svc hunt-group 461 X25 switch svc xot Related command display x25 switch-table svc X25 switching Syntax x25 switching Undo x25 switching X25 timer hold X25 timer idleExample # Enable X.25 switching function Syntax x25 timer hold minutes Undo x25 timer hold X25 timer tx0 Syntax x25 timer tx0 seconds Undo x25 timer tx0Related command x25 timer tx1, x25 timer tx2, x25 timer tx3 465 X25 timer tx1 X25 timer tx2Syntax x25 timer tx1 seconds Undo x25 timer tx1 Related command x25 timer tx0, x25 timer tx2, x25 timer tx3 X25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx3Syntax x25 timer tx3 seconds Undo x25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx2 X25 vc-range X25 vc-per-mapSyntax x25 vc-per-map count Undo x25 vc-per-map Undo x25 window-size X25 window-size469 X25 xot pvc X25 x121-addressSyntax x25 x121-address x.121-address Undo x25 x121-address Related command display x25 vc, x25 switching Undo x25 pvc pvc-number1XOT channel parameter option 471 X29 timer inviteclear-time Link Aggregation Configuration Commands Display lacp system-idDisplay link-aggregation interface Syntax display lacp system-id Link Aggregation Configuration Commands Syntax display link-aggregation summary Display link-aggregation summary475 Display link-aggregation verbose Example # Display the link aggregation group summarySyntax display link-aggregation verbose agg-id AL ID 477 Lacp port-priority Lacp system-priority Link-aggregation group descriptionExample # Assign Lacp priority 64 to a port 479 Link-aggregation group mode Related command display link-aggregation verboseRelated command display link-aggregation summary Port link-aggregation group Reset lacp statistics Related command Display link-aggregation verbose ExamplePort-group aggregation Port-group aggregation agg-id Related command display link-aggregation interface Example # Clear statistics about Lacp on all ports View User view Default Level 1 Monitor level Link Aggregation Debugging CommandsDebugging lacp packet Link Aggregation Debugging Commands Length of the Terminator field in the protocol packet is Device sent an Lacp protocol packet through Ethernet 1/1485 Device received an Lacp protocol packet through Ethernet 1/1 Debugging lacp state 487 Debugging link-aggregation error Syntax debugging link-aggregation error Error Debugging link-aggregation eventSyntax debugging link-aggregation event 489 Aggregation group 10 existed. It contained Ethernet 1/1 # Remove aggregation groupAggregation group 10 was removed Operation key of port Ethernet 1/1 Key 1 was removed Modem Modem Configuration CommandsModem auto-answer Modem timer answer Syntax modem timer answer time Undo modem timer answer Sendat Sendat command can issue only one AT command at a timeWith caution under the guidance of technicians Specifies the communication standard to be adopted Service modem-callback Example # Send dialing command to call numberSyntax service modem-callback 495 Undo service modem-callback Example # Enable the callback function Port Mirroring Configuration Commands Display mirroring-groupMirroring-group Syntax display mirroring-group groupid local Mirroring-group mirroring-port Undo mirroring-group groupid local Mirroring-group monitor-port 499 Mirroring-port # Add POS 5/1 to local port mirroring group # Add Cpos 6/1 to local port mirroring group Monitor-port501 Port Mirroring Configuration Commands Display interface mp-group PPP and MP Configuration 31 CommandsSyntax display interface mp-group mp-number Related command interface virtual-template Display interface virtual-templateSyntax display interface virtual-template number Example # View the information about VT Description on the fields of the display ppp mp command Display ppp mpLink-protocol ppp , ppp mp 505 Display virtual-access For description on the output fields, refer to Table Interface mp-group 507 Interface virtual-template Ip address ppp-negotiate Ppp account-statistics enable Ppp account-statistics enableUndo ppp account-statistics enable Link-protocol ppp Ppp authentication-mode Ppp authentication-mode chap pap call-in domain isp-nameUndo ppp authentication-mode Chap, pap Authentication modes. Use either mode Ppp chap password Related command ppp authentication-modechapPpp chap user Syntax ppp chap user username Ppp ipcp dns Related command ppp authentication-modeUndo ppp chap user Ppp ipcp dns admit-any Ppp ipcp dns requestSyntax ppp ipcp dns admit-any Undo ppp ipcp dns admit-any Syntax ppp ipcp dns request Undo ppp ipcp dns request Related command remote address Ppp ipcp remote-address forced Undo ppp lqc Ppp lqc515 Ppp mp Ppp mp binding-modeSyntax ppp mp Undo ppp mp Related command Ppp mp user Example Ppp mp max-bindPpp mp max-bind max-bind-num Undo ppp mp max-bind Related command Ppp mp Example Ppp mp min-bindPpp mp min-bind min-bind-num Undo ppp mp min-bind Related command dialer threshold on Ppp mp min-fragmentPpp mp min-fragment size Undo ppp mp min-fragment Ppp mp mp-group Ppp mp userSyntax ppp mp mp-group number Undo ppp mp Example # Add interface Serial 3/0 to MP-group Related command ppp mp and ppp mp max-bind Ppp mp virtual-templateSyntax ppp mp virtual-template number Undo ppp mp 521 Ppp timer negotiate Related command local-useron page 1940, password onSyntax ppp timer negotiate seconds Undo ppp timer negotiate Ppp pap local-user Undo remote address Remote address523 Timer hold Display ppp compression iphc rtp PPP Link Efficiency Mechanism Configuration CommandsDisplay ppp compression iphc tcp Ip tcp vjcompress Display ppp compression stac-lzsSyntax ip tcp vjcompress Undo ip tcp vjcompress Ppp compression iphc 527 Ppp compression iphc rtp-connections Ppp compression stac-lzs Ppp compression iphc tcp-connections529 Ppp mp lfi Syntax ppp mp lfi Undo ppp mp lfi Reset ppp compression iphc Ppp mp lfi delay-per-frag531 PPP Link Efficiency Mechanism Configuration Commands Display pppoe-server session Pppoe Server Configuration CommandsDisplay pppoe-server session all packet Pppoe-server bind Pppoe-server log-information off Pppoe-server max-sessions remote-mac Pppoe-server max-sessions local-mac535 Reset pppoe-server Pppoe-server max-sessions totalPppoe-server max-sessions total number Undo pppoe-server max-sessions total 537 Pppoe Server Configuration Commands Pppoe Client Configuration Commands Display pppoe-client session Pppoe-client dial-bundle-number Reset pppoe-client Related command Reset pppoe-clientReset pppoe-client all dial-bundle-number number Related command pppoe-client Sysname reset pppoe-client all PPP Debugging Commands Debugging ppp Description on the fields of the debugging ppp event command Description on the fields of the debugging ppp ipcp command 545 LCP moved from the initial state to the starting state Description on the fields of the debugging ppp ipcp commandLCP moved from the starting state to the reqsent state 547 PPP Debugging Commands Bridging Configuration Commands Bridge bridge-set enableSyntax bridge bridge-setenable Undo bridge bridge-setenable Bridge aging-time Bridge enable Example # Enable bridge set# Enable IP bridging on bridge set Syntax bridge enable Undo bridge enable Example # Enable bridging Bridge learningBridge mac-address 551 Bridge routing Bridge routing-enable Syntax bridge routing-enable Undo bridge routing-enableBridge-set Syntax bridge-set bridge-set Undo bridge-set bridge-set Display bridge address-table Display bridge information Syntax display bridge information bridge-set bridge-set555 Dynamic S--STATIC Display bridge traffic Syntax display interface bridge-template interface-number Display interface bridge-template557 Syntax fr map bridge dlci broadcast Undo fr map bridge dlci Fr map bridgeUP/DOWN Related command display fr map-infoon Bridge routing-enableInterface bridge-template Parameters Related command interface bridge-template Mac-address bridge-template interface viewMap bridge-group Syntax mac-address mac-address Undo mac-address Reset bridge traffic Reset bridge address-table561 X25 map bridge X25 map bridge x121-address x.121-address broadcastUndo x25 map bridge x121-address x.121-address Display x25 map on Isdn Configuration Commands Dialer isdn-leased Isdn BRI interface viewDialer isdn-leased 128k number Undo dialer isdn-leased 128k number Display isdn active-channel Display isdn call-info Example # Display the current state of Isdn interface 2/0 565 Display isdn call-record Display isdn parameters 567 Display isdn spid IsdnKbri Kpri Isdn bch-local-manage 569 Bch-local-manage command on the user side Channels in ascending order by defaultIsdn bch-select-way Isdn caller-number Isdn calling Isdn check-called-numberUndo isdn calling Undo isdn check-called-number check-index Isdn check-time Syntax isdn check-time date-time Undo isdn check-time Isdn crlength Isdn ignore connect-ackUndo isdn crlength Syntax isdn ignore connect-ack Settings must be the same as those on the exchange Isdn ignore hlcUndo isdn ignore connect-ack Isdn ignore hlc Isdn ignore llc Voice calls placed on the BRI interface 1/0Isdn ignore llc Undo isdn ignore llc Configured Isdn ignore sending-completeIsdn ignore sending-complete incoming outgoing Undo isdn ignore sending-complete incoming outgoing Isdn L3-timer Undo isdn L3-timer all timer-nameDescription of Q931 timers Value range Default Timer-name Seconds Isdn link-mode Isdn number-propertySyntax isdn link-mode p2p Undo isdn link-mode View Isdn BRI interface 579 Types and code schemes of Isdn numbersProtocol Field Bit value Definition Type Code scheme NTT Qsig Set the type and code scheme of Isdn numbers 581 Isdn overlap-sending Calls Isdn pri-slipwnd-size 583 Isdn protocol-type Isdn protocol-modeSyntax isdn protocol-type protocol Undo isdn protocol-type Isdn q921-permanent Example # Apply Isdn Etsi on interface BRI 1/0Syntax isdn q921-permanent Undo isdn q921-permanent View Isdn BRI interface view Isdn send-restart Isdn spid autotriggerSyntax isdn send-restart Undo isdn send-restart Syntax isdn spid autotrigger Isdn spid timer Syntax isdn spid timer seconds Undo isdn spid timerIsdn spid nit Syntax isdn spid nit Undo isdn spid nit Isdn spid service audio data speech Isdn spid serviceUndo isdn spid service Isdn spid resend Isdn spid1Syntax isdn spid resend times Undo isdn spid resend Syntax isdn spid1 spid LDN Undo isdn spid1 Isdn spid2Syntax isdn spid2 spid LDN Undo isdn spid2 Configuration of the Isdn calling command This command applies only on NI-compliant BRI interfacesSpid String of 1 to 20 digits LDN Local dialing number, a string of 1 to 30 digits Isdn two-tei Syntax isdn two-tei Permanent-active Undo isdn two-teiView BRI interface view Syntax permanent-active Undo permanent-active Power-source Syntax power-source Undo power-source # Bring up BRI 2/0 595 Isdn Configuration Commands Mstp Configuration Commands Active region-configurationCheck region-configuration Syntax active region-configuration Display stp Port numberBrief Displays brief information Information Related commands reset stp 599 Display stp abnormal-port Display stp abnormal-portAbnormally blocked ports Root guard action Display stp down-port Display stp historySyntax display stp down-port Syntax display stp instance instance-id history Display stp region-configuration Syntax display stp region-configuration Related commands stp region-configuration Description on the fields of the display stp root commandDisplay stp root Syntax display stp root Display stp tc ModelSent Tree instance, in port name order Instance Region-nameExamples # Map Vlan 2 to MST instance Syntax region-name name Undo region-name Reset stp interface interface-list Reset stpDisplay stp Syntax stp enable disable Undo stp Revision-levelStp Syntax revision-level level Undo revision-level Related commands stp mode Examples # Enable the Mstp feature globally# Disable Mstp on port Ethernet 1/1 Stp bpdu-protection Stp bridge-diameter Stp compliance Stp config-digest-snooping Stp cost Stp edged-port enable disable Or undo stp edged-port enable command to non-edge portStp edged-port Undo stp edged-port Examples # Configure port Ethernet 1/1 as a non-edge port Stp loop-protectionStp max-hops Syntax stp loop-protection Undo stp loop-protection Stp mcheck Syntax stp mcheck Stp no-agreement-check Stp modeStp mcheck , stp Examples # Enable No Agreement Check on Ethernet 1/1 Stp pathcost-standardView System view Parameters 802.1D-1998 Stp point-to-point 617 Stp port-log Stp port priority 619 Stp instance instance-id priority priority Stp priorityUndo stp instance instance-id priority Stp region-configuration Stp root primary Stp root secondary Stp instance instance-id root secondary Syntax stp tc-protection enable Stp tc-protection disable Stp root-protectionStp tc-protection Syntax stp root-protection Undo stp root-protection Stp timer forward-delay Stp tc-protection threshold Syntax stp timer hello centi-seconds Undo stp timer hello Stp timer hello625 Stp timer max-age Syntax stp timer-factor number Undo stp timer-factor Stp timer-factor627 Vlan-mapping modulo Stp transmit-limitSyntax vlan-mapping modulo modulo Examples # Map VLANs to MSTIs as per the modulo value 629 Mstp Configuration Commands Display interface vlan-interface Vlan Configuration CommandsSyntax display interface vlan-interface vlan-interface-id Vlan interfaces will be displayed Vlan-interface-id Vlan interface ID# Display the information of VLAN-interface Related command vlan Display vlanExample # Display Vlan 2 information # Display Vlan 3 information Related command display interface vlan-interface Description on the fields of the display vlan commandInterface vlan-interface Example # Create Vlan interface Ip address Related command display ip interface on635 Vlan View Vlan interface view Related command display vlan Example # Enter Vlan 2 view# Create Vlan 4 through Vlan 637 Vlan Configuration Commands PORT-BASED Vlan Configuration Commands Port access vlanSyntax port access vlan vlan-id Undo port access vlan Port Port hybrid pvid vlan Related command port link-typeSyntax port hybrid pvid vlan vlan-id Undo port hybrid pvid Port hybrid vlan 641 Port link-type Port trunk permit vlan Syntax port trunk pvid vlan vlan-id Undo port trunk pvid Port trunk pvid vlan643 Related command port link-type Voice Vlan Configuration Commands Voice vlan enable Example Syntax voice vlan vlan-idenableDisplay voice vlan state Voice vlan Undo voice vlan enable Related command display voice vlan stateVoice vlan aging Syntax voice vlan aging minutes Undo voice vlan aging Syntax voice vlan enable Undo voice vlan enable Voice vlan enableVoice vlan mac-address Ffff-f000-0000 Range of 1 to 30 charactersBe a broadcast, multicast or address of all 0s or all fs Display voice vlan oui Example Voice vlan security enable Voice vlan mode autoSyntax voice vlan mode auto Undo voice vlan mode auto Example # Disable the security mode of the voice Vlan 651 Voice Vlan Configuration Commands Port Isolation Configuration Commands Port-isolate enableSyntax port-isolate enable Undo port-isolate enable Display port-isolate group Port Isolation Configuration Commands Standby routing-group Dynamic Route Backup Configuration CommandsStandby routing-rule Standby timer routing-disable Logical Interface Configuration Commands Broadcast-limit linkDisplay interface loopback Syntax display interface loopback number Example # View the status of Loopback Related command interface loopbackSyntax display interface mfr mfr-number Related command interface mfr Example # View the state information about MFR659 LMI Dlci Related command interface mp-group Example # View the state information of MP-group Related command interface null Display interface nullDisplay interface virtual-ethernet Syntax display interface null Example # View the state information about VE Related command interface virtual-ethernetExample # View the state information about VT Description of the fields of the display mfr command 663 Interface, state of the link layer, and the name Interface ethernet 665 Interface loopback Related command display interface loopbackExample # Create Loopback Interface null Example # Create MFRExample # Create MP-group Interface null Interface virtual-ethernet Related command display interface nullExample # Enter Null 0 interface view 669 Logical Interface Configuration Commands Controller cpos Cpos Interface Configuration CommandsSystem view Display controller cpos Display controller cpos cpos-number Possible error types This table, FRED, COFA, and SEF are alarm errors AERRs673 Some information about T1 channels is omitted Display controller cpos e1Syntax display controller cpos cpos-numbere1 e1-number Syntax display controller cpos cpos-numbert1 t1-number Display controller cpos t1675 VC-3 Example # Bundle timeslots on E1 channel 677 E1 set clock Example # Enable external payload loopback on E1 channel Related command display controller cpos e1679 Syntax e1 e1-numbershutdown undo e1 e1-numbershutdown Syntax e1 e1-numberunframed undo e1 e1-numberunframed Display controller cpos Undo flag j0 j1 c2Syntax frame-format sdh sonet undo frame-format Multiplex mode Use the undo loopback command to remove a loopback# Enable external loopback on interface Cpos 1/0 Syntax multiplex mode au-3 au-4 undo multiplex mode Example # In SDH mode, multiplex AUG to AU-3 Related command frame-format683 Example # Shut down Cpos physical interface 1/0 Example # Bundle timeslots on T1 channel 685 Example # Enable external loopback on T1 channel Related command display controller cpos t1Syntax t1 t1-numbershutdown Undo t1 t1-numbershutdown Syntax t1 t1-numberunframed Undo t1 t1-numberunframed 687 Cpos Interface Configuration Commands ARP Configuration Commands Arp check enableSyntax arp check enable Undo arp check enable Arp max-learning-num Arp static Arp timer aging Related command reset arp, display arpRelated command display arp timer aging Display arp Description on the fields of the display arp command Related command arp static, reset arp# Display the number of all ARP entries Display arp timer aging Arp static , and reset arp ExampleDisplay arp timer aging Arp timer aging Naturemask-arp enable Related command arp static and reset arpSyntax naturemask-arp enable Undo naturemask-arp enable Display arp vpn-instance Specified by the argument interface-type interface-number Reset arpArp static and display arp ARP Configuration Commands Gratuitous ARP Configuration Commands Gratuitous-arp-sending enableGratuitous-arp-learning enable Gratuitous-arp-sending enable Sysname system-view Sysname gratuitous-arp-learning enable ARP Source Suppression Configuration Commands Arp source-suppression enableArp source-suppression limit Display arp source-suppression Related command display arp source-suppression Display arp source-suppressionSyntax display arp source-suppression Description on fields of display arp source-suppression Authorized ARP Configuration Commands Arp authorized enableSyntax arp authorized enable Undo arp authorized enable Arp authorized time-out Authorized ARP Configuration Commands Proxy ARP Configuration Commands Proxy-arp enableLocal-proxy-arp enable Related command display proxy-arp Related command display local-proxy-arp Proxy-arp enableLocal-proxy-arp enable Display proxy-arp Dhcp Server Configuration Commands Bootfile-name Dhcp enableSyntax bootfile-name bootfile-name Undo bootfile-name Syntax dhcp enable Undo dhcp enable Dhcp select server global-pool Dhcp server detectSyntax dhcp server detect Undo dhcp server detect 707 Dhcp server forbidden-ip Dhcp server ip-pool Dhcp server ping timeout Related command dhcp enableDhcp server ping packets Example # Create the Dhcp address pool identified by Dhcp update arp Dhcp server relay information enableSyntax dhcp update arp Undo dhcp update arp Reset dhcp server conflict Display dhcp server conflictDisplay dhcp server expired Display dhcp server conflict all ip ip-address Display dhcp server free-ip Display dhcp server forbidden-ipDisplay dhcp server free-ip Syntax display dhcp server forbidden-ip Reset dhcp server ip-in-use Display dhcp server ip-in-useBinding information of all address pools is displayed Information of Dhcp address pools or an IP address Reset dhcp server statistics Display dhcp server statisticsSyntax display dhcp server statistics Example # Display the statistics on the Dhcp server Display dhcp server tree Display dhcp server tree all pool pool-nameInformation of Dhcp address pools 715 Dns-list Undo dns-list ip-addressall Domain-name Related command dhcp server ip-poolExpired Gateway-list Netbios-type Related command dhcp server ip-pooland netbios-typeNbns-list 719 Network Related command dhcp server ip-pooland nbns-listUndo network Undo option code Option721 Reset dhcp server ip-in-use Reset dhcp server conflictReset dhcp server statistics Related command display dhcp server statistics Static-bind client-identifierExample # Clear the statistics of the Dhcp server 723 Static-bind ip-address Tftp-server domain-name Static-bind mac-address725 Voice-config Undo voice-config as-ip fail-over ncp-ip voice-vlanTftp-server ip-address View Dhcp address pool view 727 Dhcp Server Configuration Commands Dhcp Relay Agent Configuration Commands Dhcp Snooping cannot be configured on the Dhcp relay agentSyntax dhcp relay address-check disable enable Dhcp relay address-check Dhcp relay information enable Dhcp relay information format Dhcp relay information strategy drop keep replace Dhcp relay information strategyUndo dhcp relay information strategy Dhcp relay release ip Dhcp relay security staticSyntax dhcp relay release ip client-ip Undo dhcp relay security ip-address all dynamic static Dhcp relay security tracker Related command display dhcp relay security733 Dhcp relay server-detect Dhcp relay server-groupDhcp relay server-detect Undo dhcp relay server-detect Dhcp relay server-select Related command display dhcp relay server-group735 Dhcp update arp Dhcp select relayDhcp select relay Undo dhcp select relay Display dhcp relay Display dhcp relay securityServer group that a specified interface corresponds to Groups correlated to an interface or all interfaces Display dhcp relay security statistics Display dhcp relay security trackerDisplay dhcp relay security statistics Information about bindings of Dhcp relay agents Display dhcp relay server-group Display dhcp relay statisticsInterval is 10 seconds Syntax display dhcp relay server-group group-idall Server Client Reset dhcp relay statistics Reset dhcp relay statistics server-group group-idWhich to remove statistics from the relay agent Display dhcp relay statistics Dhcp Relay Agent Configuration Commands Dhcp Client Configuration Commands Description on fields of the display dhcp client command Ip address dhcp-alloc 745 Dhcp Client Configuration Commands Dhcp Snooping Configuration Commands Related command display dhcp-snoopingDhcp-snooping Dhcp-snooping trust Related command display dhcp-snooping trust Display dhcp-snoopingDisplay dhcp-snooping trust Dhcp-snooping Related command dhcp-snooping trust Example Trusted ports# Display information about trusted ports 749 Dhcp Snooping Configuration Commands Bootp Client Configuration Commands Bootp clientDisplay information about Bootp clients on all interfaces Including sub-interfaces and Vlan interfaces Ip address bootp-alloc Syntax ip address bootp-alloc Undo ip address bootp-allocRelated command display bootp client Description on fields of the display bootp client command Dhcp Debugging Commands Debugging dhcp server all error event packetUndo debugging dhcp server all error event packet Debugging dhcp server DHCPmessagetype Dhcp ACK Dhcp NAK DHCP-DISCOVER packet received Checking for an expired lease755 Checking whether the IP address 22.0.0.2 is in use DHCP-REQUEST message received Debugging dhcp relay Sending a DHCP-ACK message Sysname Terminal debugging 759 Debugging dhcp client all error event packet Undo debugging dhcp client all error event packetDebugging dhcp client Then broadcast it 761 State of the Dhcp client is changed from Halt to Init 763 Head Dhcp client starts address conflict detection using ARP ARP message sent DNS Configuration Commands Display dns domainDisplay dns dynamic-host Dns domain Example Syntax display dns proxy table Display dns proxy tableTTL Related command dns server Display dns serverDisplay ip host Syntax display dns server dynamic Dns proxy enable Related command display dns domainSyntax dns proxy enable Undo dns proxy enable Dns domain Dns resolve Dns serverSyntax dns resolve Undo dns resolve Syntax dns server ip-address Undo dns server ip-address Reset dns dynamic-host Related command display dns serverRelated command display ip host Syntax reset dns dynamic-host Related command display dns dynamic-host 771 DNS Configuration Commands IP Accounting Configuration Commands Display ip countDisplay ip count inbound-packets outbound-packets exterior Firewall-denied interior Ip count enable Syntax ip count enable Undo ip count enableDescription on fields of the display ip count rule command Display ip count rule Example # Enable IP accounting Ip count exterior-thresholdIp count firewall-denied 775 Ip count inbound-packets Ip count interior-threshold Example # Count incoming IP packets on Ethernet1/0# Specify not to count incoming IP packets on Ethernet1/0 777 Ip count outbound-packets Ip count rule Ip count timeout Reset ip countSyntax ip count timeout minutes Undo ip count timeout Syntax reset ip count all exterior firewall interior All Clears all statistics Exterior Clears the statistics from the exterior tableInterior Clears the statistics from the interior table # Clear the statistics of all IP packets IP Addressing Configuration Commands Display ip interface Description on fields of the display ip interface command Related command display ip interface Display ip interface briefExample # Display brief information about Ethernet 1/0 783 Displayed Ip address unnumbered 785 IP Addressing Configuration Commands IP Performance Configuration Commands Display fib # Display FIB information passing ACL Description on the fields of the display fib command# Display FIB information passing the IP prefix list abc0 Display fib ip-address Display fib statisticsFor description about the above output, refer to Table Syntax display fib statistics Syntax display icmp statistics Display icmp statisticsExample # Display Icmp statistics Display ip socket 1003072 # Display all socket information Display ip statistics Description on the fields of the display ip socket commandSyntax display ip statistics Display tcp statistics Example # Display statistics of IP packetsSyntax display tcp statistics 793 Related command display tcp status and reset tcp statistics Example # Display statistics of TCP traffic 795 Related command reset udp statistics Display tcp statusDisplay udp statistics Display tcp status Ip forward-broadcast acl acl-number Ip forward-broadcastUndo ip forward-broadcast Ip redirects enable Ip ttl-expires enable Reset ip statistics Ip unreachables enableReset tcp statistics Reset udp statistics Tcp anti-naptha enableRelated command display tcp statistics Syntax reset udp statistics Tcp mss Tcp state Tcp syn-cookie enable Related command tcp anti-naptha enableThis support for this command varies with devices Syntax tcp syn-cookie enable Undo tcp syn-cookie enable Tcp timer check-state Tcp timer fin-timeoutExample # Enable the SYN Cookie feature 803 Related command tcp timer syn-timeoutand tcp window Tcp timer syn-timeoutRelated command tcp timer fin-timeoutand tcp window Syntax tcp window window-size Undo tcp window Tcp window805 IP Performance Configuration Commands IP Unicast Policy Routing Configuration Commands Apply default output-interfaceApply ip-address default next-hop View policy-based-route view Apply ip-address next-hop Parameters ip-address IP address of the default next hopUndo apply ip-address next-hop ip-address ip-address Apply ip-precedence Examples # Set the next hop to 1.1.1.1 for matched packetsIP precedences and the corresponding keywords 809 Display ip policy-based-route Apply output-interfaceSyntax display ip policy-based-route Display ip policy-based-route setup 811 Local Displays statistics of enabled system policy routing Display ip policy-based-route statisticsInterface-number Routing statistics Related commands if-matchpacket-length Display policy-based-routeIf-match acl Syntax display policy-based-route policy-name If-match packet-length Related commands if-match aclIp local policy-based-route Related commands policy-based-route Related commands ip local policy-based-routeIp policy-based-route Policy-based-route Related commands if-match acl and if-matchpacket-length Reset policy-based-route statisticsSyntax reset policy-based-route statistics policy-name 817 IP Unicast Policy Routing Configuration Commands UDP Helper Configuration Commands Reset udp-helper packetReset udp-helper packet Display udp-helper server Syntax udp-helper enable Undo udp-helper enable Udp-helper enableUdp-helper port Udp-helper server Related command display udp-helper server821 UDP Helper Configuration Commands Urpf Configuration Commands Ip urpf loose strict allow-default-route acl acl-numberIp urpf Undo ip urpf Urpf Configuration Commands Fast Forwarding Commands Display ip fast-forwarding cacheIp fast-forwarding Display ip fast-forwarding cache Fast Forwarding Commands Syntax reset ip fast-forwarding cache Reset ip fast-forwarding cache827 Fast Forwarding Commands IPV6 Basics Configuration Commands Display dns ipv6 dynamic-hostDisplay dns ipv6 server Syntax display dns ipv6 dynamic-host Example # Display IPv6 DNS server information Display ipv6 fibSyntax display ipv6 fib ipv6-address Description on fields of the display ipv6 fib command Display ipv6 fibcacheDisplay ipv6 host Syntax display ipv6 fibcache Display ipv6 interface Shutdown command 833 Display ipv6 neighbors Display ipv6 neighbors count Static vlan vlan-id count Description on fields of the display ipv6 pathmtu command Display ipv6 pathmtuDisplay ipv6 socket Syntax display ipv6 pathmtu ipv6-addressall dynamic static Description on fields of the display ipv6 socket command Display ipv6 statisticsSyntax display ipv6 statistics 837 Description on fields of the display ipv6 statistics command 839 Display tcp ipv6 statistics Display tcp ipv6 statisticsStatistics # Display the statistics of IPv6 TCP connections 841 Display tcp ipv6 status Syntax display tcp ipv6 status Display udp ipv6 statistics Syntax display udp ipv6 statistics843 TCP6CB Dns server ipv6 Ipv6Syntax ipv6 Undo ipv6 Ipv6 address auto link-local Ipv6 address845 Ipv6 address eui-64 Ipv6 address link-local Ipv6 fibcache Ipv6 fib-loadbalance-type hash-basedSyntax ipv6 fibcache Undo ipv6 fibcache 847 Ipv6 icmp-error Ipv6 host Ipv6 icmpv6 multicast-echo-reply enable Ipv6 mtuSyntax ipv6 mtu mtu-size Undo ipv6 mtu 849 Ipv6 nd autoconfig managed-address-flag Ipv6 nd autoconfig other-flagIpv6 nd autoconfig managed-address-flag Undo ipv6 nd autoconfig managed-address-flag Ipv6 nd dad attempts Ipv6 nd hop-limitSyntax ipv6 nd dad attempts value Undo ipv6 nd dad attempts Syntax ipv6 nd hop-limit value Undo ipv6 nd hop-limit Ipv6 nd ns retrans-timer Ipv6 nd nud reachable-time Ipv6 nd ra halt Syntax ipv6 nd ra halt Undo ipv6 nd ra haltOn a router # Suppress RA messages on Ethernet1/0 853 Ipv6 nd ra interval Ipv6 nd ra prefixUndo ipv6 nd ra interval Undo ipv6 nd ra prefix ipv6-prefix Ipv6 nd ra router-lifetime 855 Ipv6 neighbor Ipv6 neighbors max-learning-num Ipv6 pathmtuUndo ipv6 pathmtu ipv6-address 857 Reset dns ipv6 dynamic-host Related command display ipv6 pathmtuSyntax reset dns ipv6 dynamic-host Ipv6 pathmtu age Reset ipv6 neighbors Reset ipv6 fibcacheReset ipv6 pathmtu Reset ipv6 statistics Reset tcp ipv6 statisticsReset udp ipv6 statistics ICMPv6 packets Tcp ipv6 timer fin-timeout Tcp ipv6 timer syn-timeoutExample # Clear the statistics of all UDP packets 861 Tcp ipv6 window Syntax tcp ipv6 window size Undo tcp ipv6 window NAT-PT Configuration Commands Display natpt address-groupDisplay natpt address-mapping Display natpt address-group Display natpt aging-time Syntax display natpt aging-time Example # Display all NAT-PT configuration information Display natpt allDisplay natpt all 865 Display natpt frag-sessions Syntax display natpt frag-sessions Display natpt session Display natpt statisticsSyntax display natpt session all icmp tcp udp Display natpt statistics Natpt address-group Undo natpt address-group group-number Natpt aging-time Natpt enable Syntax natpt enable Undo natpt enableNatpt max-session Syntax natpt max-session max-number Undo natpt max-session Example # Configure a NAT-PT prefix Natpt prefixUndo natpt prefix natpt-prefix 871 Natpt turn-off tos Natpt turn-off traffic-classNatpt turn-off tos Undo natpt turn-off tos Natpt v4bound static Natpt v4bound dynamic873 Natpt v6bound dynamic Reset natpt dynamic-mappings Syntax reset natpt dynamic-mappingsNatpt v6bound static Undo natpt v6bound static ipv6-addressipv4-address Reset natpt statistics Reset natpt statistics# Clear all NAT-PT statistics information Dual Stack Configuration Commands Ipv6 address auto link-local Automatically create a link-local address for an interfaceAutomatically created link-local address Ethernet interface view Example # Configure a link-local address on Ethernet 1/1 879 Dual Stack Configuration Commands Tunneling Configuration Commands Related command interface tunnel and sourceDestination Undo destination Syntax display interface tunnel number Display interface tunnelExample # Display information of the interface tunnel Syntax display ipv6 interface tunnel number Display ipv6 interface tunnel883 Encapsulation-limit Interface tunnelSyntax encapsulation-limit number Undo encapsulation-limit Syntax interface tunnel number Example # Create the interface tunnel Undo interface tunnel number885 Source Related command interface tunnel and destinationUndo source Ipv4-ipv6 Tunnel-protocolUndo tunnel-protocol Tunneling Configuration Commands Apply destination-based-forwarding IPV6 Unicast Policy Routing Configuration CommandsView IPv6 policy-based-route view Apply ipv6-address default next-hop Apply ipv6-address next-hop Apply ipv6-precedenceExample # Set a next hop of 11 for matched IPv6 packets Preferences and the corresponding keywords Apply output-interface Display ipv6 config policy-based-route Syntax display ipv6 config policy-based-route policy-nameDisplay ipv6 policy-based-route Display ipv6 policy-based-route Display ipv6 policy-based-route setup Local Displays system policy routing information Related command if-matchpacket-length Display ipv6 policy-based-route statisticsIf-match acl6 Syntax if-match acl6 acl6-number Undo if-match acl6 Ipv6 local policy-based-route Related command if-match acl6Example # Permit the packets matching ACL Related command ipv6 local policy-based-route Ipv6 policy-based-route interface viewIpv6 policy-based-route system view 897 IPV6 Unicast Policy Routing Configuration Commands Terminal Access Configuration Commands Auto-closeAuto-link Syntax auto-close time Undo auto-close Bind vpn-instance Syntax bind vpn-instance vpn-name Undo bind vpn-instance Data protect router-unix Data read blockView Terminal template view Syntax data read block Undo data read block Syntax data send delay milliseconds Undo data send delay Data send delayDisplay rta # Display brief information about TTY 903 TTY # Display all the information about terminal access Description on the fields of the display rta all command# Display statistics about terminal 905 # Display terminal access statistics Driverbuf saveDriverbuf size Syntax driverbuf save Undo driverbuf save Idle-timeout Syntax idle-timeout seconds Undo idle-timeoutUndo driverbuf size 907 Related command print information and print menu Menu hotkeyMenu screencode Syntax menu hotkey ascii-code&1-3 Undo menu hotkey Syntax print connection-info Undo print connection-info Print connection-info909 Related command print information Related command print connection-infoand print menuPrint information Print menu Print language RedrawkeyPrint language chinese english Terminal template view Reset rta statistics Reset rta connectionReset rta statistics terminal-number Resetkey Related command display rtaUndo resetkey Rta bind Rta rtc-server listen-port Rta server enable Syntax rta server enable Undo rta server enableRta source-ip Syntax rta source-ip ip-address Undo rta source-ip Rta template Rta terminalHiding TCP connections Syntax sendbuf bufsize size Undo sendbuf bufsize Sendbuf bufsize917 Tcp Sendbuf thresholdSyntax sendbuf threshold value Undo sendbuf threshold # Disable TCP delay Testkey# Set the TCP send buffer size to 512 bytes Undo testkey Update changed-config AccessUpdate changed-config Values are used for the hotkeys of flow control Vty description Vty hotkeyUndo vty vty-numberdescription 921 Vty password Vty rtc-server remote Vty rtc-client remote923 Vty screencode Related command menu screencodeUndo vty vty-numberscreencode Vty telnet remote Vty tty remoteExample # Set the screen code for VTY 1 to E!9Q 925 Vty-switch priority Vty-switch thresholdSyntax vty-switch priority Undo vty-switch priority Syntax vty-switch threshold times Undo vty-switch threshold 927 Terminal Access Configuration Commands IP Routing Table Commands Bandwidth-based-sharingDisplay ip routing-table Syntax bandwidth-based-sharing Undo bandwidth-based-sharing Special characters for regular expressions String, the end of a string 931 Display ip routing-table acl Syntax display ip routing-table acl acl-number verbose 933 IP Routing Table Commands Display ip routing-table ip-address 935 Display ip routing-table ip-address Display ip routing-table ip-address maskDisplay ip routing-table ip-addresslonger-match Display ip routing-table ip-address mask longer-match 937 Display ip routing-table ip-prefix For detailed description of the above output, see Table Display ip routing-table protocol939 # Display summary information about static routes Display ip routing-table statisticsView Any view Display ip relay-route Display ip relay-tunnelDisplay ip relay-route vpn-instance vpn-instance-name # Display recursive route information Display load-sharing ip address Display ipv6 routing-tableExamples # Display recursive tunnel information Syntax display ipv6 routing-table Syntax display ipv6 routing-table acl acl6-number verbose Display ipv6 routing-table acl943 Refer to for description about the above output Display ipv6 routing-table ipv6-addressDisplay ipv6 routing-table ipv6-addressprefix-length Display ipv6 routing-table ipv6-address1 ipv6-address2 945 Display ipv6 routing-table ipv6-prefix Display ipv6 routing-table protocol Display ipv6 routing-table statistics Syntax display ipv6 routing-table statistics# Display routing statistics 947 Display ipv6 routing-table verbose Display ipv6 relay-routeDisplay ipv6 routing-table verbose Entire routing table and information for each route Display ipv6 relay-tunnel Display ipv6 relay-tunnel# Display IPv6 recursive tunnel information 949 Load-bandwidth Reset load-sharingSyntax load-bandwidth bandwidth Undo load-bandwidth Reset ip routing-table statistics protocol Reset ipv6 routing-table statisticsReset ipv6 routing-table statistics protocol all protocol Ripng , or static Sysname reset ipv6 routing-table statistics protocol all BGP Configuration Commands Configuration Commands onAggregate Functions of the keywords If-match clause of the route-policy command Balance BGP/BGP-VPN instance viewSyntax balance number Undo balance Suppress-policy Related commands display bgp routing-table Bestroute as-path-neglect BGP/BGP-VPN instance viewView BGP view/BGP-VPN instance view 955 Comparison is not enabled by default Bestroute compare-med BGP/BGP-VPN instance viewBestroute med-confederation BGP/BGP-VPN instance view Syntax bestroute compare-med Undo bestroute compare-med Compare-different-as-med BGP/BGP-VPN instance view Bgp957 Confederation id Syntax confederation id as-number Undo confederation id Related commands confederation id and confederation peer-as Confederation nonstandardConfederation peer-as View BGP view Dampening BGP/BGP-VPN instance view Undo confederation peer-as as-number-listExamples # Specify confederation peer sub ASs 2000 Undo dampening Default ipv4-unicast Examples # In BGP view, configure BGP route dampeningSyntax default ipv4-unicast Undo default ipv4-unicast 961 Default med BGP/BGP-VPN instance view Default local-preference BGP/BGP-VPN instance viewSyntax default med med-value Undo default med Syntax default-route imported Undo default-route imported Default-route imported BGP/BGP-VPN instance view963 Related commands import-routeBGP/BGP-VPN instance view Description on the fields of the display bgp group commandDisplay bgp group Syntax display bgp group group-name Advertised with the network command Display bgp networkDisplay bgp network # Display routing information that has been advertised Description on the fields of the display bgp paths command Display bgp pathsDisplay bgp peer MED Description on the fields of the display bgp peer command 967 Description on the fields of the display bgp routing command Display bgp routing-table Display bgp routing-table as-path-acl 969 Display bgp routing-table cidr Display bgp routing-table cidr Display bgp routing-table community-list Display bgp routing-table community971 Display bgp routing-table dampened Display bgp routing-table dampenedDampened BGP routes # Display dampened BGP routes Related commands dampening BGP/BGP-VPN instance view Display bgp routing-table dampening parameterDisplay bgp routing-table different-origin-as Display bgp routing-table dampening parameter Display bgp routing-table flap-info Longer-match Display bgp routing-table peer Related commands display bgp peer975 Display bgp routing-table regular-expression Display bgp routing-table statisticEbgp-interface-sensitive Display bgp routing-table statistic Undo ebgp-interface-sensitive Filter-policy export BGP/BGP-VPN instance view977 Filter-policy import BGP/BGP-VPN instance view Graceful-restart timer restart Graceful-restart BGP viewSyntax graceful-restart Undo graceful-restart 979 Graceful-restart timer wait-for-rib Graceful-restart timer wait-for-rib timerUndo graceful-restart timer wait-for-rib Using this command can speed up route convergence Import-route BGP/BGP-VPN instance view 981 Log-peer-change Syntax log-peer-change Undo log-peer-change Network BGP/BGP-VPN instance view 983 Peer advertise-community BGP/BGP-VPN instance view Peer advertise-ext-community BGP/BGP-VPN instance view Peer allow-as-loop BGP/BGP-VPN instance view Related commands display bgp routing-table peer985 Peer as-path-acl BGP/BGP-VPN instance view Peer as-number BGP/BGP-VPN instance viewUndo peer ip-address Peer capability-advertise conventional 987 Peer capability-advertise route-refresh Peer default-route-advertise BGP/BGP-VPN instance view Undo peer group-nameip-address default-route-advertisePeer connect-interface BGP/BGP-VPN instance view Undo peer group-name ip-address connect-interface Peer description BGP/BGP-VPN instance view Peer ebgp-max-hop BGP/BGP-VPN instance view 991 Syntax peer ip-addressenable Undo peer ip-addressenable Peer enable BGP viewPeer fake-as BGP/BGP-VPN instance view Peer filter-policy BGP/BGP-VPN instance view Related commands peer as-path-aclBGP/BGP-VPN instance view993 Peer group BGP/BGP-VPN instance view Peer ip-prefix Peer ignore BGP/BGP-VPN instance view995 Peer keep-all-routes BGP/BGP-VPN instance view Peer log-change BGP/BGP-VPN instance view Peer next-hop-local BGP/BGP-VPN instance viewUndo peer group-name ip-address next-hop-local View BGP view /BGP-VPN instance view Peer password # Perform the similar configuration on the peer Peer preferred-value BGP/BGP-VPN instance viewUndo peer group-name ip-address preferred-value 999 Peer public-as-only BGP/BGP-VPN instance view Undo peer group-name ip-address public-as-only Peer reflect-client BGP/BGP-VPN instance view 1001 Peer route-limit BGP/BGP-VPN instance view Peer route-policy BGP/BGP-VPN instance view Peer route-update-interval BGP/BGP-VPN instance view 1003 Peer substitute-as BGP/BGP-VPN instance view Undo peer group-nameip-address substitute-as Related commands timer BGP/BGP-VPN instance view Peer timer BGP/BGP-VPN instance view1005 Preference BGP/BGP-VPN instance view Reflect between-clients BGP viewUndo preference Syntax reflect between-clients Undo reflect between-clients Examples # Disable route reflection between clients Reflector cluster-id BGP viewExamples # Set the cluster ID to 1007 Reset bgp All Resets all BGP connectionsAs-number Resets BGP connections to peers in the AS Refresh bgp Reset bgp flap-info Reset bgp dampening1009 Reset bgp ipv4 all Syntax reset bgp ipv4 allRouter-id Syntax router-id router-id Undo router-id Syntax summary automatic Undo summary automatic Summary automatic1011 Timer BGP/BGP-VPN instance view Syntax timer keepalive keepalive hold holdtime Undo timerSynchronization BGP view Syntax synchronization Undo synchronization Related commands peer timer BGP/BGP-VPN instance view 1013 BGP Configuration Commands BGP Debugging Commands Debugging bgp all BGP configuration information BGP received an Open message from the peer Syntax debugging bgp detail Undo debugging bgp detail Debugging bgp detail1017 Debugging bgp event Route was deleted from the instance BGP has received an Update message Debugging bgp graceful-restartState has changed from Opensent to Openconfirm 1019 BGP peer relationship has been successfully established BGP neighbor 10.1.1.1 is performing GRBGP GR Helper received an EOR message from peer Debugging bgp Description on the fields of the debugging bgp command1021 Description on the fields of the debugging bgp open command Information about the sent BGP Open messageAFI/ Safi WTR Information about the received BGP Open message Information about the sent BGP Keepalive messageInformation about the received BGP Keepalive message 1023 Debugging bgp timer ConnectRetry timer for BGP peer 2.2.2.2 expired Hold timer expired on BGP peer Receive Enables the debugging for received BGP packetsSend Enables the debugging for sent BGP packets Update messages Ip-prefix-name receive send verbose Debugging bgp update ipv4Ip-prefix ip-prefix-name receive send verbose Update messages of IPv4 address family Debugging bgp update ipv61027 Receive Enables/disables debugging for received BGP packets Send Enables/disables debugging for sent BGP packetsFor IPv6 BGP update messages Complete By default, this debugging is disabled Debugging bgp update l2vpn Update messages of IPv6 address familyVerbose Send verbose Debugging bgp update label-route Update messages in an L2VPN environmentAcl-number ip-prefix ip-prefix-name receive send verbose Receive send verbose Update message information of L3VPN labeled routes 1031 Debugging bgp update peer Update message information of IPv6 labeled routes Debugging bgp update vpls Vpls Update messagesFor BGP Vpls Update messages 1033 Information about the sent Vpls update message Debugging bgp update vpn-instanceInformation about the received Vpls update message Debugging bgp update vpnv4 BGP VPNv4 Update messagesFor BGP VPNv4 Update messages Examples None Update message information of VPNv4 IS-IS Configuration Commands Area-authentication-modeArea-authentication-mode simple md5 password ip osi Undo area-authentication-mode Auto cost enable Syntax auto-cost enable Undo auto-cost enableRelated commands bandwidth-referenceIS-IS view, cost-style Bandwidth-reference IS-IS view Circuit-cost Related commands auto cost enable1039 Related commands isis cost, cost-style Cost-styleRelax-spf-limit Undo cost-style Related commands isis cost Default-route-advertise IS-IS view1041 Description on the fields of the display isis brief command Display isis brief Display isis debug-switches Display isis graceful-restart status Display isis interface Traffic-eng Displays IS-IS traffic engineering informationVerbose Displays IS-IS interface detail information Tunnel Displays IS-IS tunnel information Examples # Display IS-IS enabled interface information # Display detailed IS-IS interface information1045 DIS Syntax display isis license Display isis licenseBFD Display isis lsdb License information varies with device models Lspid Display isis mesh-groupATT/P/OL # Display the configuration information of IS-IS mesh-group # Configure a static mapping for the remote IS-IS systemDisplay isis name-table Display isis peer Display isis route Up state and direct interface’s IP address# Display detailed IS-IS neighbor information PRI # Display IS-IS IPv4 routing information Description on the fields of the display isis route command1051 Display isis spf-log Display isis statistics Domain-authentication-mode Simple Specifies to send the password in plain textMd5 Specifies to send the password encrypted with MD5 IS-IS view Filter-policy export IS-IS view 1055 Related commands filter-policy import IS-IS view Filter-policy import IS-IS view Related commands filter-policy export IS-IS view Flash-floodLevel-1 level-2 Undo flash-flood level-1 level-2 Graceful-restart interval IS-IS view Graceful-restart IS-IS viewGraceful-restart Graceful-restart suppress-sa Import-route IS-IS viewGraceful-restart suppress-sa Undo graceful-restart suppress-sa Related commands import-route isis level-2 into level-1 Related commands import-routeIS-IS view Import-route isis level-2 into level-1Examples # Redistribute static routes and set the cost to Undo import-route isis level-2 into level-1 Isis authentication-mode Isis This command is not available in loopback interface view Isis circuit-level level-1 level-1-2 level-2Undo isis circuit-level 1063 Isis circuit-type Related commands is-levelSyntax isis circuit-type p2p Undo isis circuit-type Syntax isis dis-name symbolic-name Undo isis dis-name Isis costIsis dis-name 1065 Examples # Configure the name as Localarea for the local LAN Isis dis-priority Isis enable Syntax isis enable process-id Undo isis enableRelated commands isis, network-entity Isis mesh-group Isis peer-ip-ignore Syntax isis peer-ip-ignore Undo isis peer-ip-ignore Isis small-hello Syntax isis silent Undo isis silentSyntax isis small-hello Undo isis small-hello 1069 Isis timer csnp Isis timer hello Isis timer holding-multiplier value level-1 level-2 Isis timer holding-multiplierUndo isis timer holding-multiplier level-1 level-2 Isis timer lsp Related commands isis timer helloSyntax isis timer lsp time count count Undo isis timer lsp Related commands isis timer retransmit Isis timer retransmit Related commands Examples Isis timer lspIs-level Syntax is-level level-1 level-1-2 level-2 Undo is-level Related commands isis circuit-level Examples # Configure the router to work in Level-1Is-name Syntax is-name sys-name Undo is-name Is-snmp-traps enable Syntax is-snmp-traps enable Undo is-snmp-trapsIs-name map Undo is-name map sys-id Log-peer-change IS-IS view Lsp-fragments-extend Lsp-length originate 1077 # Restore the default Lsp-length receiveMaximum load-balancing IS-IS view Syntax lsp-length receive size Undo lsp-length receive Related commands Isis, isis enable Examples Network-entityPreference IS-IS view Network-entity net Reset isis all Examples # Clear all IS-IS data structure information Reset isis peer Set-overloadAllow interlevel external Undo set-overload Spf-slice-size Syntax spf-slice-size duration-time Undo spf-slice-size Summary IS-IS view 1083 Timer isp-generation Undo timer lsp-generation level-1 level-2Generation interval Interval Timer lsp-max-age Timer lsp-refreshSyntax timer lsp-max-age seconds Undo timer lsp-max-age Related commands timer lsp-refresh Timer spf Related commands timer lsp-max-ageUndo timer spf Examples # Set the LSP refresh interval to 1500 seconds Virtual-system # Set the maximum SPF calculation interval to 15 secondsUndo virtual-system virtual-system-id 1087 IS-IS Configuration Commands IS-IS Debugging Commands Event Enables IS-IS event debuggingDebugging isis Ha-events interface-information memory-allocating IS-IS Debugging Commands 1091 Snpa Snpa Field CircuitName not enabled 1093 SNP packet length mismatch 1095 Length length Updt Reset Required 1097 Sending pduLevel pduType on circuitName Sending pduLevel Csnp PDU fails 1099 Tent New Distance from RootNodeSourceId 1101 LSP LevelType LSP level, which can be L1 or L2 1103 IP address took effect on the IS-IS interface Router B sent Csnp packets 1105 IS-IS Debugging Commands Ospf Configuration Commands Related commandsL3VPN Configuration Commands on Abr-summary Ospf area view Area Ospf view Asbr-summarySyntax area area-id Undo area area-id Authentication-mode Simple Specifies the simple authentication modeDisplay ospf asbr-summary View Ospf area view Default Related commands ospf authentication-modeSyntax default cost cost limit limit tag tag type type Bandwidth-reference Ospf view Default-cost Ospf area view Undo default cost limit tag typeRelated commands import-route Ospf view Syntax default-cost cost Undo default-cost Default-route-advertise Ospf view Related commands stub Ospf area view, nssaDefault-route-advertise summary cost cost Undo default-route-advertise Description OSPF/OSPF area view Display ospf abr-asbrSyntax description description Undo description # Describe the Ospf area0 as bone area Display ospf asbr-summary Related commands asbr-summary Display ospf briefSyntax display ospf process-id brief Examples # Display Ospf brief information Description on the fields of the display ospf brief command Mpls TE Syntax display ospf process-id cumulative Display ospf cumulative1117 Display ospf error Syntax display ospf process-id errorNssa ASE/NSSA Description on the fields of the display ospf error command 1119 Display ospf interface 1121 Display ospf lsdbBDR Description on the fields of the display ospf lsdb command # Display Type2 LSA Network LSA information in the Lsdb Display ospf nexthop Syntax display ospf process-id nexthop1123 LS ID Display ospf peer Description on the fields of the display ospf peer command Display ospf peer statistics# Display brief Ospf neighbor information Syntax display ospf process-id peer statistics Display ospf request-queue Keep neighbor relationship Init Examples # Display Ospf request list information Display ospf retrans-queue1127 Display ospf routing Description on the fields of the display ospf vlink command Display ospf vlinkSyntax display ospf process-id vlink 1129 Enable link-local-signaling Enable logError Enables error logging State Enables state logging Filter import/export Enable out-of-band-resynchronization1131 By default, Summary LSAs filtering is disabled This command is only available on an ABRFilter-policy export Ospf view Undo filter-policy export protocol process-id Examples # Filter redistributed routes using ACL Filter-policy import Ospf viewGraceful-restart Ospf view 1133 Examples # Enable Ietf Graceful Restart for Ospf process # Enable non-IETF Graceful Restart for Ospf processGraceful-restart help Syntax graceful-restart help acl-numberprefix prefix-list Related commands ospf timer dead Graceful-restart interval Ospf viewHost-advertise 1135 Import-route Ospf view Related commands Examples Default-route-advertise Ospf viewImport-route command cannot redistribute default routes 1137 Related commands lsa-generation-interval Lsa-arrival-interval Related commands lsa-arrival-interval Lsa-generation-intervalLsdb-overflow-limit Undo lsa-generation-interval Maximum-routes Maximum load-balancing Ospf viewNumber Maximum route number in the range 1 to Related commands ospf Network Ospf area viewNssa 1141 Opaque-capability enable Related commands default-cost Ospf area viewExamples # Configure area1 as an Nssa area Syntax opaque-capability enable Undo opaque-capability Ospf authentication-mode OspfUndo ospf process-id 1143 Related commands authentication-mode Syntax ospf cost value Undo ospf cost Ospf cost1145 Ospf dr-priority Ospf mib-bindingSyntax ospf dr-priority priority Undo ospf dr-priority Syntax ospf mib-binding process-id Undo ospf mib-binding Ospf mtu-enable Ospf network-type Ospf timer dead Related commands ospf dr-priorityThis command is not supported on the Null interface Syntax ospf timer dead seconds Undo ospf timer dead Ospf timer hello Related commands ospf timer helloSyntax ospf timer hello seconds Undo ospf timer hello 1149 Ospf timer retransmit Ospf timer pollSyntax ospf timer poll seconds Undo ospf timer poll Ospf trans-delay Syntax ospf trans-delay seconds Undo ospf trans-delayPeer 1151 Command sets priority for internal routes PreferenceExamples # Specify the neighbor IP address Preference ase route-policy route-policy-name value Reset ospf counters Reset ospf processSyntax reset ospf process-id process 1153 Reset ospf redistribution Syntax reset ospf process-id redistributionRfc1583 compatible Syntax rfc1583 compatible Undo rfc1583 compatible Snmp-agent trap enable ospf Silent-interface Ospf view Ospf Configuration Commands Spf-schedule-interval Stub Ospf area viewUndo spf-schedule-interval Syntax stub no-summary Undo stub Default-cost Ospf area view Stub-routerStub-router Undo stub-router Vlink-peer Ospf area view Examples # Enable a stub-router1159 Related commands authentication-mode,display ospf peer RIP Configuration Commands Default cost RIP viewSyntax default cost value Undo default cost Checkzero Default-route originate Related commands import-route RIP view# Disable default route sending Display rip Description on the fields of the display rip command 1163 Description on fields of the display rip database command Display rip databaseSyntax display rip process-iddatabase X.X/X Display rip route Display rip interface1165 RIP Configuration Commands Description on the fields of the display rip route command Filter-policy export RIP view# Display the routing statistics of RIP process 1167 Interface-type interface-number Specifies an interface Filter-policy import RIP viewExamples # Reference ACL 2000 to filter outbound routes Syntax host-route Undo host-route Host-route1169 Import-route RIP view Default cost RIP viewIncluding bgp , direct , isis , ospf , rip , rip and static Maximum load-balancing RIP view # Set the default cost for redistributed routes to1171 Syntax peer ip-address Reset rip statistics Syntax reset rip process-idstatisticsRip 1173 Rip authentication-mode Undo rip authentication-mode Mode and parameters By default, an interface is enabled to receive RIP messages# Enable Ethernet1/0 to receive RIP messages Format defined in RFC Related commands rip metricout Related commands rip metricinRip metricin Rip metricout Rip mib-binding Rip outputSyntax rip mib-binding process-id Undo rip mib-binding Syntax rip output Undo rip output Rip poison-reverse Related commands rip inputRip split-horizon Examples # Enable the split horizon function on Ethernet1/0 Related commands summaryRip summary-address Rip triggered Rip version Undo rip triggeredRip version 1 2 broadcast multicast Undo rip version Silent-interface RIP view All Silents all interfacesMessages 1181 Timers Related commands rip versionSummary Syntax summary Trip retransmit count 1183 Trip retransmit timer retransmit-time-value Trip retransmit timerUndo trip retransmit timer Validate-source-address VersionSyntax validate-source-address Undo validate-source-address Version 1 Sysname system-view Sysname rip Sysname-rip-100 version Routing Policy Common Configuration Commands Apply as-pathApply comm-list delete Syntax apply comm-list comm-list-numberdelete Apply community Undo apply comm-list Apply cost Syntax apply cost + value Undo apply costView Routing policy view Parameters + Increases cost value. + Decreases cost value Apply cost-type Apply extcommunity No level is set by default Apply isisApply isis level-1 level-1-2 level-2 Undo apply isis 1191 Related commands route-policy Apply local-preferenceApply mpls-label Syntax apply mpls-label Undo apply mpls-label Apply origin Apply preferenceSyntax apply preference preference Undo apply preference 1193 Apply tag Apply preferred-valueSyntax apply tag value Undo apply tag Display ip as-path Syntax display ip as-path as-path-acl numberExamples # Display the information of BGP AS path ACL 1195 Display ip extcommunity-list Display ip community-listSyntax display ip extcommunity-list ext-comm-list-number Display route-policy If-match as-pathSyntax display route-policy route-policy-name Examples # Display the information of routing policy Related commands route-policyand ip community-list Related commands route-policy,ip as-pathaclIf-match community If-match cost If-match extcommunitySyntax if-match cost value Undo if-match cost 1199 If-match interface If-match mpls-label If-match route-type If-match tag Ip as-pathSyntax if-match tag value Undo if-match tag Undo ip as-path as-path-number Ip community-list 1203 Sysname system-view Sysname ip community-list 100 permit Ip extcommunity-list Route-policyUndo ip extcommunity-list ext-comm-list-number 1205 Routing Policy Common Configuration Commands Display ip ip-prefix IPV4 Routing Policy Configuration CommandsSyntax display ip ip-prefix ip-prefix-name Related commands ip ip-prefix Examples # Display the statistics of IPv4 prefix list abc If-match ip Related commands Route-policy ExamplesIf-match ip-prefix Ip ip-prefix Syntax reset ip ip-prefix ip-prefix-name Reset ip ip-prefix1211 IPV4 Routing Policy Configuration Commands IPV6 Routing Policy Configuration Commands Apply ipv6 next-hopDisplay ip ipv6-prefix Syntax display ip ipv6-prefix ipv6-prefix-name If-match ipv6 Next-hop Matches the next hop of IPv6 routing informationString of 1 to 19 characters Address based match criterion for IPv6 routes Ip ipv6-prefix 1215 Syntax reset ip ipv6-prefix ipv6-prefix-name Reset ip ipv6-prefixExamples # Clear the statistics of IPv6 prefix list abc Static Routing Configuration Commands Delete static-routes allIp route-static Examples # Delete all static routes on the router Configured gateway-address Must be identical to that configured in the NQA test group Ethernet interface and Vlan interfaceAssociate it with a Track entry 1219 Ip route-static default-preference Examples # Set the default preference of static routes to IPV6 BGP Configuration Commands Related commands display ipv6 routing-tableonBalance IPv6 address family view Bestroute as-path-neglect IPv6 address family view Bestroute compare-med IPv6 address family view Bestroute med-confederation IPv6 address family view Compare-different-as-med IPv6 address family view 1223 Dampening IPv6 address family view Default med IPv6 address family view Default local-preferenceIPv6 address family view1225 Display bgp ipv6 group Default-route imported IPv6 address family viewSyntax display bgp ipv6 group ipv6-group-name Syntax display bgp ipv6 network Display bgp ipv6 network1227 Display bgp ipv6 paths Syntax display bgp ipv6 paths as-regular-expression 1229 Display bgp ipv6 peerIncomplete Display bgp ipv6 routing-table Field Description Local router ID Display bgp ipv6 routing-table as-path-acl 1231 Display bgp ipv6 routing-table community Examples # Display routes filtered through the AS path ACL Display bgp ipv6 routing-table community-list Display bgp ipv6 routing-table dampenedSyntax display bgp ipv6 routing-table dampened Examples # Display IPv6 BGP dampened routes Display bgp ipv6 routing-table dampening parameter Display bgp ipv6 routing-table different-origin-asSyntax display bgp ipv6 routing-table dampening parameter Syntax display bgp ipv6 routing-table different-origin-as Display bgp ipv6 routing-table flap-info Examples # Display IPv6 BGP routes from different ASsExamples # Display IPv6 BGP route flap statistics 1235 Command Display bgp ipv6 routing-table labelSyntax display bgp ipv6 routing-table label Examples # Display IPv6 BGP label routing information Display bgp ipv6 routing-table regular-expression Display bgp ipv6 routing-table peer1237 Display bgp ipv6 routing-table statistic Filter-policy exportIPv6 address family viewParameters as-regular-expression AS regular expression Syntax display bgp ipv6 routing-table statistic Filter-policy import IPv6 address family view 1239 Group IPv6 address family view Import-route IPv6 address family viewExamples # Reference ACL6 2001 to filter all inbound routes Syntax group ipv6-group-name internal external Ipv6-family Network IPv6 address family viewSyntax ipv6-family Undo ipv6-family 1241 Peer advertise-community IPv6 address family view Peer allow-as-loop IPv6 address family view Peer advertise-ext-community IPv6 address family view1243 Peer as-number IPv6 address family view Import export Peer as-path-acl IPv6 address family view1245 Peer connect-interface IPv6 address family view Peer description IPv6 address family view Peer default-route-advertise1247 Peer ebgp-max-hop IPv6 address family view Peer fake-as IPv6 address family view Peer enable IPv6 address family view1249 Peer filter-policy IPv6 address family view Peer ignore IPv6 address family view Peer group IPv6 address family view1251 Peer ipv6-prefix Peer label-route-capability IPv6 address family view Peer keep-all-routes IPv6 address family view1253 Peer log-change IPv6 address family view Peer next-hop-local IPv6 address family view Peer preferred-value IPv6 address family view 1255 Peer public-as-only IPv6 address family view Peer reflect-client IPv6 address family view Peer route-limit IPv6 address family view 1257 Peer route-update-interval IPv6 address family view Peer route-policy IPv6 address family view Peer substitute-as IPv6 address family view Undo peer ipv6-group-nameipv6-address route-update-interval1259 Related commands timer IPv6 address family view Peer timer IPv6 address family viewPreference IPv6 address family view Reflect between-clients IPv6 address family view 1261 Reflector cluster-id IPv6 address family view Examples # Enable route reflection between clientsRefresh bgp ipv6 Reset bgp ipv6 1263 Reset bgp ipv6 dampening Reset bgp ipv6 flap-info Synchronization IPv6 address family view 1265 Timer IPv6 address family view Related commands peer timer IPv6 address family view 1267 IPV6 BGP Configuration Commands IPV6 IS-IS Configuration Commands # Display detailed IPv6 IS-IS routing information Ipv6 default-route-advertise 1271 Ipv6 enable Syntax ipv6 enable Undo ipv6 enableIpv6 filter-policy export Undo ipv6 filter-policy export protocol process-id Related commands ipv6 filter-policy import Ipv6 filter-policy importUndo ipv6 filter-policy import 1273 Related commands ipv6 filter-policy export Ipv6 import-route Undo ipv6 import-route isisv6 level-2 into level-1 Ipv6 import-route isisv6 level-2 into level-11275 Ipv6 maximum load-balancing Ipv6 preference Ipv6 summary 1277 Examples # Configure a summary route of 2002/32 Isis ipv6 enableSyntax isis ipv6 enable process-id Undo isis ipv6 enable Abr-summary OSPFv3 area view IPV6 OSPFV3 Configuration CommandsArea OSPFv3 view Default cost Default-cost OSPFv3 area viewSyntax default-cost value Examples # Enter OSPFv3 Area 0 view Related commands stubOSPFv3 area view Display debugging ospfv3Display debugging ospfv3 Debugging state information Display ospfv3 Description on the fields of the display isofv3 commandSyntax display ospfv3 process-id Display ospfv3 interface 1283 Display ospfv3 lsdb # Display Link-local LSA information in the Lsdb 1285 Display ospfv3 lsdb statistic Syntax display ospfv3 lsdb statistic Display ospfv3 next-hop Display ospfv3 peerSyntax display ospfv3 process-id next-hop Interface-type interface-number interface type and number Description on the fields of the display isofv3 peer command Display ospfv3 peer statistic Display ospfv3 request-listSyntax display ospfv3 peer statistic Syntax display ospfv3 process-id request-list statistics Display ospfv3 retrans-list # Display the statistics of OSPFv3 link state request listSyntax display ospfv3 process-id retrans-list statistics LS-ID Display ospfv3 routing 1291 # Display the statistics of OSPFv3 routing table Display ospfv3 statistic Display ospfv3 topologySyntax display ospfv3 statistic Syntax display ospfv3 process-id topology area area-id Display ospfv3 vlink Syntax display ospfv3 process-id vlink Filter-policy exportOSPFv3 view 1295 Filter-policy importOSPFv3 view Routes that fail to pass are not added to the routing table Import-routeOSPFv3 view Allow-ibgp direct static cost value type type route-policyDirect static Both Ebgp and Ibgp routes Maximum load-balancingOSPFv3 view Process Related commands router-id Ospfv3Ospfv3 area Undo ospfv3 process-id Ospfv3 cost Ospfv3 dr-priority Ospfv3 mtu-ignore Ospfv3 timer dead1301 Ospfv3 timer hello Related commands ospfv3 timer hello Ospfv3 timer retransmit Ospfv3 trans-delayRelated commands ospfv3 timer dead 1303 Preference ase route-policy route-policy-name preference Related commands Ospfv3 Silent-interfaceOSPFv3 viewRouter-id router-id OSPFv3 processes on a router Spf timers Undo spf timers Related commands default cost Examples # Configure OSPFv3 area 1 as a stub areaUndo vlink-peer router-id hello retransmit trans-delay dead StubOSPFv3 area view IPV6 OSPFV3 Configuration Commands IPV6 Ripng Configuration Commands Default cost RIPng viewSyntax default cost cost Undo default cost View RIPng view Display ripng Related commands import-routeSyntax display ripng process-id Description on the fields of the display ripng command Description on fields of the display ripng database commandDisplay ripng database Syntax display ripng process-iddatabase Display ripng interface Syntax display ripng process-idroute Display ripng route1313 Filter-policy export Filter-policy import RIPng view Import-route 1315 Related commands default cost on Maximum load-balancing RIPng view # Restore the default RIPng route priority # Disable RIPng processRipng Undo ripng process-id Ripng enable Ripng default-routeSyntax ripng process-idenable Undo ripng enable Related commands ripng metricout Ripng metricinRipng metricout Syntax ripng metricin value Undo ripng metricin Related commands ripng metricin Ripng poison-reverseRipng split-horizon Syntax ripng poison-reverse Undo ripng poison-reverse Information, refer to Frame Relay Configuration Commands on Lapb and X.25 Configuration Commands onRipng summary-address Poison reverse function takes effect Timers 1323 IPV6 Ripng Configuration Commands IPV6 Static Routing Configuration Commands Delete ipv6 static-routes allIpv6 route-static Delete ipv6 static-routes all Sysname system-view Sysname ipv6 route-static 112 24 Related command multicast boundary Multicast Routing Forwarding Configuration CommandsDisplay multicast boundary Display multicast forwarding-table Major values of the flags field 1329MID Value Meaning Related command multicast minimum-ttl Display multicast minimum-ttl Display multicast routing-table Related command display multicast forwarding-table1331 Display multicast routing-table static Description on the fields of display multicast routing-table Display multicast rpf-info 1333 Ip rpf-route-static 1335 Related command display multicast routing-table static Mtracert Multicast boundary Description on the fields of the mtracert command1337 Related command display multicast boundary Multicast forwarding-table downstream-limit Multicast forwarding-table route-limit 1339 Multicast load-splitting Multicast longest-matchSyntax multicast longest-match Undo multicast longest-match View System view, VPN instance view Multicast routing-enable Related command display multicast minimum-ttlMulticast minimum-ttl 1341 Reset multicast forwarding-table # Enable IP multicast routing in VPN instance mvpn Reset multicast routing-table 1343 Sysname reset multicast routing-table Igmp Configuration Commands Display igmp group Description on the fields of the display igmp group command Display igmp interface 1347 Display igmp routing-table Related command igmp fast-leave,last-member-query-interval Fast-leave Igmp viewIgmp Syntax fast-leave group-policy acl-number Undo fast-leave Igmp enable Related command igmp enable, and multicast routing-enableonSyntax igmp enable Undo igmp enable Related command igmp Igmp fast-leave Igmp group-policyUndo igmp group-policy 1351 Igmp last-member-query-interval By default, the last-member query interval is 1 secondIgmp max-response-time Igmp require-router-alert 1353 Robust-count Igmp view , igmp timer query , igmp Igmp robust-countIgmp send-router-alert Igmp interface Igmp static-group Igmp timer other-querier-present Igmp timer query Related command version Igmp view Igmp versionLast-member-query-interval Undo igmp version Require-router-alert Igmp view Max-response-time Igmp viewSyntax require-router-alert Reset igmp group Undo require-router-alertView Public instance Igmp view, VPN instance Igmp view 1359 Robust-count Igmp view Related command display igmp groupSyntax robust-count robust-value Undo robust-count Timer other-querier-present Igmp view Send-router-alert Igmp viewSyntax send-router-alert Undo send-router-alert 1361 Syntax timer query interval Undo timer query Timer query Igmp viewPublic instance Version Igmp view Related command igmp version1363 Igmp Configuration Commands Msdp Configuration Commands Cache-sa-enableDisplay msdp brief Characters Display msdp peer-status 1367 Display msdp sa-cache Related command cache-sa-enable 1369 Display msdp sa-count Encap-data-enable Syntax encap-data-enable Undo encap-data-enableImport-source View Public instance Msdp view, VPN instance Msdp view Related command display multicast routing-tableon Related command peer sa-policyMsdp Originating-rp Peer connect-interfaceUndo originating-rp 1373 Related command static-rpf-peer Related command display msdp peer-statusPeer description Peer mesh-group Peer minimum-ttl Undo peer peer-addressmesh-groupUndo peer peer-addressminimum-ttl 1375 Peer request-sa-enable Peer sa-cache-maximum Import-source command Peer sa-policyFrom the Msdp peer Display msdp peer-status and import-source Reset msdp peer Peer sa-request-policy Related command cache-sa-enableand display msdp sa-cache Reset msdp sa-cache1379 Shutdown Msdp View Reset msdp statisticsUndo shutdown peer-address Related command display msdp peer-statusand ip prefix-list Example # Configure static RPF peers in the public instanceStatic-rpf-peer Undo static-rpf-peer peer-address Timer retry Syntax timer retry interval Undo timer retry PIM Configuration Commands Auto-rp enableRelated command static-rp PIM view Bsr-policy PIM view Bsr PIM view Undo c-bsr Bsr admin-scope Syntax c-bsr admin-scope Undo c-bsr admin-scopeBsr global 1385 Bsr group Undo c-bsr group group-address Bsr hash-length PIM view Bsr holdtime PIM viewSyntax c-bsr hash-length hash-length Undo c-bsr hash-length Syntax c-bsr holdtime interval Undo c-bsr holdtime Related command c-bsr PIM view and c-bsr interval PIM view Bsr interval PIM viewBsr priority PIM view Bsr PIM view and c-bsr holdtime PIM view Rp PIM view 1389 Related command c-bsr PIM view Rp advertisement-interval PIM viewRp advertisement-interval interval Undo c-rp advertisement-interval Related command c-rp PIM view and c-bsr interval PIM view Rp holdtime PIM viewCrp-policy PIM view Syntax c-rp holdtime interval Undo c-rp holdtime Related command c-bsr PIM view and c-rp PIM view Display pim bsr-info Display pim claimed-route 1393 Display pim control-message counters 1395 BSR Display pim grafts Description on the fields of the display pim grafts commandDisplay pim interface 1397 Display pim join-prune PIM DR Display pim neighbor 1399 Interface connecting the PIM neighbor Display pim routing-table 1401 Sysname display pim routing-table Vpn-instance public net Display pim rp-info 1403 Description on the fields of the display pim rp-info command Related command pim hello-optiondr-priority Hello-option dr-priority PIM viewHello-option holdtime PIM view 1405 Hello-option lan-delay PIM view This command is effective for both PIM-DM and PIM-SMRelated command pim hello-option holdtime Hello-option neighbor-tracking PIM view Hello-option override-interval PIM view Related command pim hello-optionneighbor-tracking1407 Holdtime join-prune PIM view Holdtime assert PIM viewSyntax holdtime assert interval Undo holdtime assert Related command jp-queue-size PIM view Jp-pkt-size PIM viewJp-queue-size PIM view Syntax jp-pkt-size packet-size Undo jp-pkt-size Pim Related command multicast routing-enableonUndo pim vpn-instance vpn-instance-name Pim dm Pim bsr-boundaryBsr PIM view , and multicast boundary on Related command pim sm, ssm-policy PIM view Example # Enable PIM-DM on Ethernet 1/0Related command hello-optiondr-priority PIM view Pim hello-option dr-priority Pim hello-option lan-delay Related command hello-option holdtime PIM viewPim hello-option holdtime 1413 Pim hello-option neighbor-tracking Pim hello-option override-interval Pim holdtime join-prune Pim holdtime assert1415 Pim sm Pim require-genidView Interface view Parameter None Pim timer graft-retry Related command pim dmExample # Enable PIM-SM on Ethernet 1/0 Example # Disable state refresh on Ethernet 1/0 Pim timer hello Pim timer join-pruneSyntax pim timer hello interval Undo pim timer hello Related command timer hello PIM view Pim triggered-hello-delay Related command timer join-prune PIM viewProbe-interval PIM view Syntax probe-interval interval Undo probe-interval Register-suppression-timeout PIM view Related command register-suppression-timeout PIM viewSyntax register-suppression-timeout interval Register-policy PIM view Undo register-suppression-timeout Register-whole-checksum PIM viewSyntax register-whole-checksum Undo register-whole-checksum 1421 Reset pim control-message counters Related command state-refresh-interval PIM viewSource-lifetime PIM view Syntax source-lifetime interval Undo source-lifetime Spt-switch-threshold PIM view Undo spt-switch-threshold group-policy acl-numberSource-policy PIM view Syntax source-policy acl-number Undo source-policy PIM Configuration Commands Ssm-policy PIM view State-refresh-interval PIM viewSyntax ssm-policy acl-number Undo ssm-policy 1425 State-refresh-ttl PIM view State-refresh-rate-limit PIM viewSyntax state-refresh-ttl ttl-value Undo state-refresh-ttl By default, the TTL value of state refresh messages is Static-rp PIM viewUndo static-rp rp-address 1427 Timer hello PIM view Timer join-prune PIM viewRelated command display pim rp-infoand auto-rp enable Related command pim timer hello Timer spt-switch PIM view Related command pim timer join-pruneSyntax timer spt-switch interval Undo timer spt-switch Related command spt-switch-threshold PIM view PIM Configuration Commands IPV6 Multicast Routing Forwarding Configuration Commands Related command multicast ipv6 boundaryDisplay multicast ipv6 boundary Display multicast ipv6 forwarding-table IPV6 Multicast Routing and Forwarding Configuration Commands Values and meanings of the Flags field Display multicast ipv6 minimum-hoplimit1433 Related command multicast ipv6 minimum-hoplimit Display multicast ipv6 routing-table Display multicast ipv6 rpf-info Related command display multicast ipv6 forwarding-table1435 Multicast ipv6 boundary Multicast ipv6 forwarding-table downstream-limit Related command display multicast ipv6 boundary1437 Multicast ipv6 forwarding-table route-limit Multicast ipv6 load-splitting Multicast ipv6 minimum-hoplimit Multicast ipv6 longest-match1439 Multicast ipv6 routing-enable Related command display multicast ipv6 minimum-hoplimit Reset multicast IPv6 routing-table Reset multicast ipv6 forwarding-table1441 Sysname reset multicast ipv6 routing-table ff03101 MLD Configuration Commands Display mld group Display mld interface Description on the fields of the display mld group commandInformation of all interfaces running MLD Display mld routing-table 1445 Fast-leave MLD view Syntax fast-leave group-policy acl6-number Undo fast-leave Last-listener-query-interval Max-response-time MLD viewSyntax max-response-time interval Undo max-response-time 1447 Mld enable Syntax mld enable Undo mld enableMld Syntax mld Related command mld Example # Enable MLD on Ethernet 1/0Mld fast-leave Mld group-policy Mld last-listener-query-interval Mld require-router-alert Mld max-response-time1451 Mld robust-count Syntax mld robust-count robust-value Undo mld robust-count Mld send-router-alert Mld static-groupMld send-router-alert Undo mld send-router-alert Mld timer other-querier-present Mld timer other-querier-present intervalUndo mld timer other-querier-present 125 x 2 + 10 / 2 = 255 seconds Mld timer query Syntax mld timer query interval Undo mld timer queryRelated command mld version Mld version Reset mld group Require-router-alert MLD viewRequire-router-alert Mld require-router-alert and send-router-alert MLD view Related command display mld group Robust-count MLD view# Clear all MLD forwarding entries on Ethernet 1/0 1457 Timer other-querier-present MLD view By default, the MLD querier robustness variable isSend-router-alert MLD view View MLD view Related command Timer query MLD viewTimer query interval Version MLD view Example # Globally set the MLD version to MLDv2 IPV6 PIM Configuration Commands Bsr-policy IPv6 PIM viewBsr IPv6 PIM view Syntax bsr-policy acl6-number Undo bsr-policy Related command c-bsr IPv6 PIM view on Bsr hash-length IPv6 PIM view Example # Set the bootstrap timeout time to 150 seconds Bsr holdtime IPv6 PIM viewBsr interval IPv6 PIM view Syntax c-bsr interval interval Undo c-bsr interval Related command c-bsr IPv6 PIM view Bsr priority IPv6 PIM viewRp IPv6 PIM view Bsr IPv6 PIM view and c-bsr holdtime IPv6 PIM view View IPv6 PIM view Rp advertisement-interval IPv6 PIM view1465 Related command c-rp IPv6 PIM view Example # Set the global C-RP timeout time to 200 secondsRp holdtime IPv6 PIM view Example # Set the global C-RP-Adv interval to 30 seconds Related command c-bsr IPv6 PIM view and c-rp IPv6 PIM view Crp-policy IPv6 PIM viewDisplay pim ipv6 bsr-info Syntax crp-policy acl6-number Undo crp-policy Display pim ipv6 claimed-route Syntax display pim ipv6 claimed-route ipv6-source-address Display pim ipv6 control-message counters BSR Display pim ipv6 grafts Display pim ipv6 interfaceDisplay pim ipv6 grafts Unacknowledged graft messages Interface PIM version PIM mode Display pim ipv6 join-prune PIM-SM and IPv6 PIM-SSM respectivelyTo send on the specified interface Specified IPv6 PIM neighbor Display pim ipv6 neighbor Display pim ipv6 routing-table 1475 Related command display multicast ipv6 routing-tableon Example # View the content of the IPv6 PIM routing table Syntax display pim ipv6 rp-info ipv6-group-address Display pim ipv6 rp-info1477 Embedded-rp Syntax embedded-rp acl6-number Undo embedded-rp acl6-number Related command pim ipv6 hello-optiondr-priority Hello-option dr-priority IPv6 PIM viewHello-option holdtime IPv6 PIM view Example # Set the router priority for DR election to Hello-option lan-delay IPv6 PIM view Related command pim ipv6 hello-option holdtimeExample # Set the prune delay to 200 milliseconds globally Hello-option neighbor-tracking IPv6 PIM view Related command pim ipv6 hello-optionneighbor-tracking Example # Disable join suppression globallyHello-option override-interval IPv6 PIM view Holdtime assert IPv6 PIM view Holdtime join-prune IPv6 PIM view Related command jp-queue-size IPv6 PIM view Jp-pkt-size IPv6 PIM viewJp-queue-size IPv6 PIM view 1483 Related command multicast ipv6 routing-enableon Pim ipv6Pim ipv6 bsr-boundary Syntax pim ipv6 Undo pim ipv6 Related commands pim ipv6 sm, ssm-policy IPv6 PIM view Example # Enable IPv6 PIM-DM on Ethernet 1/0Pim ipv6 dm Syntax pim ipv6 dm Undo pim ipv6 dm Related command hello-optiondr-priority IPv6 PIM view Related command hello-option holdtime IPv6 PIM viewPim ipv6 hello-option dr-priority Pim ipv6 hello-option holdtime Pim ipv6 hello-option neighbor-tracking Pim ipv6 hello-option lan-delay1487 Related command hello-optionneighbor-tracking IPv6 PIM view Example # Disable join suppression on Ethernet 1/0Pim ipv6 hello-option override-interval Pim ipv6 holdtime assert Pim ipv6 holdtime join-prune Pim ipv6 require-genidSyntax pim ipv6 require-genid Undo pim ipv6 require-genid 1489 Pim ipv6 sm Pim ipv6 state-refresh-capablePim ipv6 sm Undo pim ipv6 sm Pim ipv6 timer hello Pim ipv6 timer graft-retry1491 Pim ipv6 timer join-prune Pim ipv6 triggered-hello-delayRelated command timer hello IPv6 PIM view Related command timer join-prune IPv6 PIM view Related command register-suppression-timeout IPv6 PIM view Probe-interval IPv6 PIM viewRegister-policy IPv6 PIM view Example # Set the probe time to 6 seconds Register-suppression-timeout IPv6 PIM view Register-whole-checksum IPv6 PIM view Reset pim ipv6 control-message counters1495 Related command state-refresh-interval IPv6 PIM view Source-lifetime IPv6 PIM viewSource-policy IPv6 PIM view Syntax source-policy acl6-number Undo source-policy Undo spt-switch-threshold group-policy acl6-number Spt-switch-threshold IPv6 PIM view1497 Ssm-policy IPv6 PIM view Syntax ssm-policy acl6-number Undo ssm-policy State-refresh-interval IPv6 PIM view State-refresh-hoplimit1499 Static-rp IPv6 PIM view State-refresh-rate-limit IPv6 PIM viewExample # Set the state refresh interval to 70 seconds Timer hello IPv6 PIM view Related command display pim ipv6 rp-infoUndo static-rp ipv6-rp-address 1501 Timer join-prune IPv6 PIM view Timer spt-switch IPv6 PIM viewRelated command pim ipv6 timer hello Related command pim ipv6 timer join-prune Related command spt-switch-threshold IPv6 PIM view 1503 IPV6 PIM Configuration Commands Display multicast-domain vpn-instance switch-group receive Multicast VPN Configuration CommandsDisplay multicast-domain vpn-instance share-group Count Display multicast-domain vpn-instance switch-group send 1507 Multicast-domain holddown-time Multicast-domain log switch-group-reuse Multicast-domain share-groupView VPN instance view 1509 Multicast-domain switch-delay Undo multicast-domain switch-group-pool Multicast-domain switch-group-pool1511 Sysname system-view Sysname ip vpn-instance mvpn Display mpls fast-forwarding cache Mpls Basics Configuration CommandsDisplay mpls fast-forwarding cache verbose Syntax display mpls ilm label include text Display mpls ilm# Display all ILM entries Display mpls interface Related command display mpls statistics interface1515 Display mpls label Display mpls label label-value1 to label-value2 all Display mpls ldp all verbose begin exclude include Display mpls ldpMpls ldp system view , mpls ldp interface view Display mpls ldp cr-lsp Description on the fields of the display mpls ldp commandLSR ID Related command display mpls lsp Display mpls ldp interfaceAll Displays all information 1519 Example # Display information about all LDP interfaces # Display detailed information about all interfaces Display mpls ldp Isp All Displays information about all LSPs established by LDPDest-addr Destination address of the LSP Established by LDP Related command display mpls ldp Display mpls ldp peer # Display detailed information about all peers Example # Display information about all peers1523 Display mpls ldp remote-peer Example # Display information about remote peer BJI Display mpls ldp session 1525 Example # Display information about sessions # Display detailed information about all sessionsLAM MD5 Display mpls ldp vpn-instance 1527 Display mpls lsp Example # Display information about VPN instance vpn1Incoming-interface Incoming interface of the LSPs Outgoing-interface Outgoing interface of the LSPs Exclude Excludes the specified FEC Include Includes the specified FECDest-addr Destination address Asbr Displays information about Asbr established LSPs Description on the fields of the display mpls lsp command Example # Display information about all LSPs# Display detailed information about all LSPs FEC Display mpls lsp statistics Display mpls nhlfeSyntax display mpls lsp statistics Syntax display mpls nhlfe token include text Display mpls route-state # Display all Nhlfe entries Display mpls static-lsp 1533 Example # Display brief information about static LSPs Display mpls statistics interface# Display detailed information about static LSPs Example # Display Mpls statistics for all interfaces Related command statistics interval1535 Display mpls statistics lsp Syntax display mpls statistics lsp index all name lsp-name Example # Display Mpls statistics for all LSPs 1537 Du-readvertise timer Syntax du-readvertise timer value Undo du-readvertise timerDu-readvertise Are both Graceful-restart Mpls LDP view Graceful-restart mpls ldpView Mpls LDP view Syntax graceful-restart mpls ldp Graceful-restart timer neighbor-liveness Graceful-restart timer reconnectRelated commands graceful-restart Mpls LDP view Syntax graceful-restart timer reconnect timer Undo graceful-restart timer reconnect Graceful-restart timer recovery1541 Related command loop-detect,path-vectors Hops-countLabel advertise Syntax hops-count hop-number Undo hops-count Label-distribution Undo label advertiseLabel-distribution independent ordered Undo label-distribution Label-retention conservative liberal Label-retentionUndo label-retention Related command hops-count,path-vectors Use the undo lsp-trigger command to restore the defaultLoop-detect Lsp-trigger # Configure the LDP LSR ID of LDP instance named vpn1 Lsr-idSyntax lsr-idlsr-id Undo lsr-id Md5-password MplsSyntax mpls Undo mpls Related command mpls lsr-id # Enable Mpls for interface Ethernet 1/0Mpls ldp system view View System view/interface view # Enable LDP for VPN instance vpn1 Mpls ldp interface viewSyntax mpls ldp Undo mpls ldp 1549 Mpls ldp advertisement dod du Mpls ldp advertisementUndo mpls ldp advertisement Mpls ldp timer hello-hold Related command remote-ipMpls ldp remote-peer Example # Create a remote peer entity named BJI Mpls ldp timer keepalive-hold Mpls ldp transport-address Mpls lsr-idView Interface view/MPLS LDP remote peer view Syntax mpls lsr-id lsr-id Undo mpls lsr-id Mtu-signalling Related command display mpls interfaceSyntax mtu-signalling Undo mtu-signalling Example # Set the LSR ID to Related command loop-detect,hops-count Path-vectorsPing lsp Syntax path-vectors pv-number Undo path-vectors Remote-ip Syntax remote-ip ip-address Undo remote-ip Reset mpls fast-forwarding cache Reset mpls ldpRelated command mpls ldp remote-peer Reset mpls fast-forwarding cache Reset mpls statistics lsp Reset mpls statistics interfaceSyntax reset mpls statistics lsp index all name lsp-name Snmp-agent trap enable mpls Related command display mpls statistics lspStatic-lsp egress Lsp-name Name for the LSP, a string of 1 to 15 characters Static-lsp ingress Undo static-lsp ingress lsp-name Undo static-lsp transit lsp-name Static-lsp transit1561 Related command static-lsp egress, static-lsp ingress Statistics intervalTracert lsp Syntax tracert lsp -a source-ip-exp Ttl expiration pop command Ttl expirationTtl expiration pop Undo ttl expiration pop Ttl propagate Mpls TE Configuration Commands Add hop Delete hop Display explicit-pathSyntax delete hop ip-address Syntax display explicit-path pathname # Display the latest TE information advertised by IS-IS TE Display isis traffic-eng advertisements1567 Intf Addr Verbose Displays details Display isis traffic-eng link1569 Display isis traffic-eng network Vpn-instance vpn-instance-name Specifies a VPN instance. Display isis traffic-eng statistics 1571 Related command te-set-subtlv Display isis traffic-eng sub-tlvs Display mpls rsvp-te Label switched Router ID, Display mpls rsvp-te established Begin include exclude regular-expressionAbout RSVP-TE globally or for an interface # Display RSVP-TE information for interface Ethernet 1/0 Filters output by regular expression Display mpls rsvp-te peerSpaces Display mpls rsvp-te psb-content 1577 Erhopstrict Display mpls rsvp-te request RSVP-TE requests on the specified or all interfaces1579 X.X Display mpls rsvp-te reservation 1581 Display mpls rsvp-te rsb-contentLSP ID Tunnel Dest Display mpls rsvp-te sender 1583 Display mpls rsvp-te statistics Global Display global RSVP-TE informationInterface is specified RSVP-TE is displayed # Display the RSVP-TE statistics of interface Serial 1/0 1585 Display mpls static-cr-lsp Ip-address prefix-length arguments # Display detailed information about all static CR-LSPs Display mpls te cspf tedb1587 IGP # Display the Tedb information of IGP area # Display all Tedb information1589 Mpls LSR ID IGP # Display the Tedb information of all nodes # Display Tedb information for a specified interface address Display mpls te link-administration admission-control Links of all interfaces if no interface is specified Description on fields of the command Display mpls te link-administration bandwidth-allocation1593 Display mpls te tunnel Egress ingress remote transit name name incoming-interface 1595 # Display detailed information about Mpls TE tunnelsLSP-ID Lsr-id Ingress LSR ID, in dotted decimal notation Display mpls te tunnel path# Display the paths that all Mpls TE tunnels traverse Display mpls te tunnel statistics Display mpls te tunnel-interfaceSyntax display mpls te tunnel statistics Syntax display mpls te tunnel-interface CR-LSP Display ospf mpls-te 1599 Area ID TE enabled Ospf area ID LSA Type Syntax display ospf process-id traffic-adjustment Display ospf traffic-adjustment1601 Syntax display tunnel-info tunnel-id all statistics Display tunnel-info# Display statistics about tunnels Enable traffic-adjustment Enable traffic-adjustment advertise# Enable IGP shortcut when the IGP protocol is IS-IS View Ospf view/IS-IS view Explicit-path List hop View Explicit path view Modify hop1605 Mpls rsvp-te authentication Mpls rsvp-te authentication cipher plain auth-keyUndo mpls rsvp-te authentication Mpls rsvp-te Mpls rsvp-te blockade-multiplier 1607 Related command mpls rsvp-te timer refresh Mpls rsvp-te graceful-restartMpls rsvp-te hello Syntax mpls rsvp-te hello Undo mpls rsvp-te hello Mpls rsvp-te hello-lost # Enable Rsvp hello extension on interface Ethernet 1/01609 Related command mpls rsvp-te timer hello Mpls rsvp-te keep-multiplierMpls rsvp-te reliability Example # Set the keep multiplier to five Mpls rsvp-te resvconfirm Mpls rsvp-te srefresh Mpls rsvp-te timer graceful-restart recovery Mpls rsvp-te timer graceful-restart restart Mpls rsvp-te timer hello Mpls rsvp-te timer refreshRelated command mpls rsvp-te hello, mpls rsvp-tehello-lost Example # Set the hello interval to five seconds Related command mpls rsvp-tekeep-multiplier Mpls rsvp-te timer retransmissionUndo mpls rsvp-te timer retransmission # Enable Mpls TE on interface Ethernet 1/0 Mpls teSyntax mpls te Undo mpls te Related command mpls te link administrative group Mpls te affinity propertyMpls te auto-bandwidth Undo mpls te auto-bandwidth Mpls te backup Related command mpls te timer auto-bandwidthMpls te backup hot-standby ordinary Undo mpls te backup With backup enabled, the record route Mpls te backup bandwidthExample # Enable hot backup on tunnel Mpls te bandwidth Mpls te bandwidth change thresholdsMpls te bandwidth bc0 bc1 bandwidth Undo mpls te bandwidth Syntax mpls te commit Mpls te commitView Tunnel interface view Mpls te cspf timer failed-link Related command mpls te cspfExample # Set the failed link timer to 50 seconds Mpls te cspf Mpls te fast-reroute bypass-tunnel Mpls te fast-rerouteSyntax mpls te fast-reroute Undo mpls te fast-reroute Mpls te igp advertise Description Example# Set the hold time to 10000 milliseconds 1623 Mpls te igp metric Mpls te igp shortcutMpls te igp shortcut isis ospf Undo mpls te igp shortcut Mpls te link administrative group Related command mpls te affinity propertyMpls te loop-detection Syntax mpls te loop-detection Undo mpls te loop-detection Mpls te max-link-bandwidth Mpls te max-reservable-bandwidth Related command mpls te path metric-type Mpls te metricUndo mpls te max-reservable-bandwidth Syntax mpls te metric value Undo mpls te metric Related command mpls te metric Mpls te path explicit-pathMpls te path metric-type Example In Mpls view Mpls te priority Mpls te record-routeUndo mpls te priority Syntax mpls te record-route label Undo mpls te record-route Mpls te reoptimization tunnel interface view Mpls te reoptimization user viewMpls te reoptimization Mpls te resv-style Mpls te retry Related command mpls te timer retry Example # Set the maximum number of tunnel setup retries toExample # Enable route pinning Mpls te route-pinning Mpls te signal-protocol Mpls te signal-protocol crldp rsvp-te staticMpls te tie-breaking Mpls te tie-breaking least-fill most-fill random By default, automatic bandwidth adjustment is disabled Mpls te timer auto-bandwidthRelated command mpls te auto-bandwidth Mpls te timer fast-reroute Mpls te timer retrySyntax mpls te timer retry second Undo mpls te timer retry 1635 Related command mpls te retry Examples # Configure the tunnel ID asMpls te tunnel-id Mpls te vpn-binding Mpls-te enable Syntax mpls-te enable Undo mpls-teRelated command opaque-capability Next hop Related command delete hop Opaque-capability Reset mpls rsvp-te statistics Reset mpls te auto-bandwidth adjustment timersSyntax reset mpls te auto-bandwidth adjustment timers Static-cr-lsp egress Static-cr-lsp ingress CR-LSP on the ingress or a transit node Static-cr-lsp transitUndo static-cr-lsp transit tunnel-name Use the undo te-set-subtlvcommand to restore the default # Configure sub-TLVs for IS-IS processBw-constraint Sets the bandwidth constraint sub-TLV Value Sub-TLV in the range 19 to If no level is specified, IS-IS TE applies to Level-1-2 Cost-style on Mpls TE Configuration Commands Mpls L2VPN Configuration Ccc interface in-label out-label Ccc interface out-interface Undo ce ce-name Connection # Create a CE named ce2 for a VPNView Mpls L2VPN CE view 1647 Display bgp l2vpn Related command route-distinguisher Mpls L2VPN viewTunnel select-seq load-balance-number on 1649 CE ID Verbose Peer Local 1651 Pref Preference Display ccc Syntax display ccc ccc-name ccc-nametype local remote# Display information about all local CCC connections # Display information about all CCC connections Display l2vpn ccc-interface vc-type Down Configured on the router Configured on the CE interfaceDisplay mpls l2vc 1655 VC ID VC ID Display mpls l2vpn Vpn-name local-ce remote-ce # Display information about L2VPN vpn1 Description on the fields of the display mpls l2vpn command# Display information about local CEs of L2VPN vpn1 # Display information about remote CEs of L2VPN vpn1 Display mpls l2vpn connection1659 Status Status of the connection Peer-id Description on the fields of mpls l2vpn connection summary Display mpls static-l2vc Display mpls l2vpn forwarding-infoExample # Display Mpls L2VPN forwarding information Syntax l2vpn-family L2vpn-family1663 Mpls l2vc Related command tunnel select-seqload-balance-numberonUndo l2vpn-family Mpls l2vpn Mpls l2vpn vpn-nameExample # Create a Martini Mpls L2VPN connection Syntax mpls l2vpn Undo mpls l2vpn # Create Kompella VPN named vpn2 and enter Mpls L2VPN view Mpls static-l2vc destinationUndo mpls static-l2vc Reset bgp l2vpn Mtu Mpls L2VPN viewSyntax mtu mtu Example # Set the MTU for Kompella connections to Re-create the VPN using the new RD Takes effect only when it is configured with an RDRoute-distinguisher Mpls L2VPN view Route-distinguisher route-distinguisher Example # Associate VPN vpn1 with VPN targets Vpn-target Mpls L2VPN view1669 Mpls L2VPN Configuration Commands Apply access-vpn vpn-instance Default local-preference BGP-VPNv4 subaddress family viewSyntax default local-preference value View Policy routing view Default med BGP-VPNv4 subaddress family view Display bgp vpnv4 all routing-table Description VPN instance view1673 Example # Display all BGP VPNv4 routing information All Specifies all VPNv4 peers Display bgp vpnv4 group1675 Display bgp vpnv4 network Display bgp vpnv4 paths Display bgp vpnv4 all vpn-instance vpn-instance-name pathsBe displayed # Display all BGP VPNv4 AS path information Verbose Displays detailed information Display bgp vpnv4 peerVPNv4 peers 1679 # Display all BGP VPNv4 peer information # Display detailed information about BGP VPNv4 peer 1681 Display bgp vpnv4 route-distinguisher routing-table Example # Display the BGP VPNv4 routing information of RD Related command route-distinguisher VPN instance view1683 Fields of the above output All Specifies all VPNv4 peers Display bgp vpnv4 routing-table label1685 Display bgp vpnv4 vpn-instance routing-table 1687 Display fib statistics vpn-instance Display fib vpn-instanceDisplay fib statistics vpn-instance Display fib vpn-instance vpn-instance-name include string # Display detailed information about a VPN instance Display ip vpn-instance1689 Related command sham-link Display ospf sham-linkSyntax display ospf process-id sham-link area area-id Example # Display information about all Ospf sham links Display tunnel-policy # Display information about Ospf sham links in areaDisplay tunnel-policy all policy-name tunnel-policy-name Tunneling policy or all tunneling policies Domain-id Example # Configure the Ospf domain ID# Display tunneling policy aaa Filter-policy export BGP-VPNv4 subaddress family view Export route-policy1693 Filter-policy import BGP-VPNv4 subaddress family view Ip binding vpn-instance Import route-policy1695 Ip vpn-instance Ipv4-familyView BGP view Vpnv4 Enters BGP-VPNv4 subaddress family view Peer advertise-community BGP-VPNv4 subaddress family view 1697 Peer allow-as-loop Peer as-path-acl BGP-VPNv4 subaddress family view Peer default-route-advertise vpn-instance 1699 Related command peer upe Peer enablePeer filter-policy BGP-VPNv4 subaddress family view Peer group 1701 Peer ip-prefix BGP-VPNv4 subaddress family view Peer label-route-capability BGP view/BGP VPN instance view Peer next-hop-invariable BGP-VPNv4 subaddress family view 1703 Peer next-hop-local Peer public-as-only BGP-VPNv4 subaddress family view Peer reflect-client 1705 Peer route-policy BGP-VPNv4 subaddress family view Peer upe Command applies to inter-provider VPN option B schemes Policy vpn-targetSyntax policy vpn-target Undo policy vpn-target 1707 Reflect between-clients Reflector culster-id Refresh bgp vpn-instance 1709 Reset bgp vpn-instance Refresh bgp vpnv4 Reset bgp vpn-instance flap-info Reset bgp vpn-instance dampening1711 Route-distinguisher VPN instance view Reset bgp vpnv4Syntax route-distinguisher route-distinguisher Then re-create the VPN instance and re-configure a new RD Route-tagInstance Syntax route-tag tag-value Undo route-tag Routing-table limit Example # Configure the route tag for Ospf process 100 asImport-route Ospf view on Rr-filter Sham-linkUndo rr-filter View Ospf area view Mpls L3VPN Configuration Commands Related command tunnel select-seqload-balance-number Tnl-policy VPN instance viewTunnel-policy Undo tnl-policy Tunnel select-seq load-balance-number Load-balance-number command can be usedUndo tunnel select-seq Vpn-instance-capability simple Vpn-target VPN instance viewView Ospf multi-instance view 1719 Mpls L3VPN Configuration Commands VAM Server Configuration Commands Authentication-algorithmAuthentication-method Vam server vpn , authentication-method Vam server vpn , authentication-algorithm Display vam server address-map Display vam server statistic Syntax display vam server statistic all vpn vpn-nameDescription on the fields of display vam server address-map 1723 Example # Display statistics of the VAM server # Display statistics of VPN domain 1 on the VAM server Related command vam server vpn Encryption-algorithmHub private-ip Undo hub private-ip private-ip-address Related command vam server vpn, keepalive retry Keepalive interval Related command vam server vpn, keepalive interval Keepalive retryPre-shared-key VPN domain view Syntax keepalive retry retry-times Undo keepalive retry Server enable Syntax server enable Undo server enableRelated command vam server vpn, vam server enable Example # Enable the VAM server function of VPN domain Related command Vam server vpn, server enable Example Vam server enableVam server ip-address Vam server vpn Syntax vam server vpn vpn-name Undo vam server vpn vpn-name VAM Client Configuration Commands Client enableRelated command vam client name, and vam client enable 100 Example # Display the status information of VAM client abc Pre-shared-key VAM client view Pre-shared-key cipher simple key-stringVAM client view Cipher Specifies a pre-shared key in cipher text No pre-shared key is configured by default Related command vam client nameResend interval Syntax resend interval time-interval Undo resend interval Server secondary ip-address Server primary ip-address1735 Vam client enable By default, no local username or password is configuredExample # Set the local username and password both to user User Vam client name and client enable By default, no VAM client is configuredVam client name An interface Undo vpn VpnExample # Specify the VAM client abc to belong to VPN Ipsec Profile Configuration Commands Related command ipsec profile system view101 Display ipsec profile Inbound ESP setting Ipsec profile system view 1741 Ipsec Profile Configuration Commands Dvpn Tunnel Configuration Commands 102Display dvpn session Associated with the VAM client Dvpn session dumb-time Dumb Dvpn session idle-time Ipsec profile tunnel interface viewUndo ipsec profile ipsec-profile-name&1-6 1745 Keepalive Undo keepalive Tunnel-protocol dvpn udp Related command Interface tunnel on ExampleSyntax tunnel-protocol dvpn udp Undo tunnel-protocol Related command interface tunnel on Example # Configure the Dvpn tunnel modeVam client Syntax vam client client-name Undo vam client Related command interface tunneland source GRE Configuration Commands103 Example # Display information about interface Tunnel0 Down 1751 Gre checksum Syntax gre checksum Undo gre checksum Related command interface tunnel Gre keyUndo gre key 1753 Syntax interface tunnel number Undo interface tunnel number 1755 Tunnel-protocol gre Syntax tunnel-protocol gre ipv6 Undo tunnel-protocol L2TP Configuration Commands 104Allow l2tp Undo allow Related command l2tp-group Related command Display l2tp tunnel ExampleDisplay l2tp session Sessions Syntax display l2tp tunnel Display l2tp tunnel1759 L2tp enable L2tp sendaccm enableRelated command allow l2tp Syntax l2tp enable Undo l2tp enable L2tpmoreexam enable L2tp enableUse the undo l2tp-group command to remove an L2TP group L2tp-group Related command allow l2tp and start l2tp Related command Mandatory-lcp ExampleMandatory-chap Mandatory-lcp Reset l2tp tunnel Related command mandatory-chapUndo mandatory-lcp View L2TP group view Tunnel authentication Related command display l2tp tunnelSyntax tunnel authentication Start l2tp Undo tunnel authentication Tunnel avp-hiddenSyntax tunnel avp-hidden Undo tunnel avp-hidden 1765 Tunnel flow-control Tunnel name Tunnel password Tunnel timer hello L2TP Configuration Commands Traffic Policing TP Configuration Commands Description on the fields of the display qos car commandDisplay qos car interface Filed Description Description on the fields of the display qos carl command Display qos carlQos car Display qos carl carl-index 1771 Qos carl Undo qos carl carl-index Examples # Configure Carl rule 1 with packet precedence 1773 Traffic Policing TP Configuration Commands Traffic Shaping Configuration Commands Description on the fields of the display qos gts command106 Display qos gts interface Qos gts Undo qos gts any acl acl-number queue queue-number Related commands acl on 1777 Traffic Shaping Configuration Commands Line Rate Configuration Commands Description on the fields of the display qos lr command107 Display qos lr interface Qos lr layer 2 interface view or port group view Qos lr interface viewUndo qos lr inbound outbound Interfaces is 4 or 9, this argument is not supported Layer 2 module interface view, port group view1781 Line Rate Configuration Commands 108 Defining Class CommandsDisplay traffic classifier If-match Undo if-match not match-criteriaClass view Match-criteria Class match rules. The values are as follow 1785 Value Description Rtp start-portEnd-port Qos-local-id Define Mpls EXP precedence matching rule # Define a class to match ACL Related commands traffic classifier1787 # Define a class to match the ACL named flow # Define a class to match IPV6 ACL# Define a class to match the IPv6 ACL named flow # Define matching rule for all packets Traffic classifier tcl-name operator and or Traffic classifierUndo traffic classifier tcl-name By default, the relation is operator Examples # Define a class named as class1 Defining Traffic Behavior Commands 109Car Undo car Display traffic behavior Qos policy , traffic behavior , classifier behavior Filter GtsFilter deny permit Undo filter Redirect Undo gtsUndo redirect View Traffic behavior view Syntax remark atm-clp atm-clp-value Undo remark atm-clp Remark atm-clp1795 Remark dot1p Remark dscpSyntax remark dot1p 8021p Undo remark dot1p Syntax remark dscp dscp-value Undo remark dscp Syntax remark fr-de fr-de-value Undo remark fr-de Remark fr-de1797 Remark ip-precedence Remark mpls-expExamples # Remark the DE bit in FR packets to Syntax remark mpls-exp exp-value Undo remark mpls-exp Traffic behavior Remark qos-local-id1799 Examples # Define a traffic behavior named behavior1 Defining Policy Commands Related commands qos policy110 Classifier behavior Description on the fields of the display qos policy command System-defined Policy pre-defined by the systemUser-defined Policy pre-defined by the user Tcl-name Class name in the policy Display qos policy interface 1803 Qos apply policy interface view EXP Qos apply policy layer 2 interface view or port group view 1805 Qos policy Syntax qos policy policy-name Undo qos policy policy-name 1807 Defining Policy Commands Fifo Queuing Configuration Commands 111Qos fifo queue-length 1809 Fifo Queuing Configuration Commands PQ Configuration Commands Related commands qos pq112 Display qos pq interface Related commands qos pq, qos pq pql Qos pqExamples # Display PQLs Syntax qos pq pql pql-index Undo qos pq Qos pql default-queue Qos pql inbound-interfaceExamples # Apply the priority list 12 to the Ethernet 1/0 1813 By default, no classification rule is configured Qos pql protocolDescription on values of queue-key and key-value Queue-key Key-value Description Qos pql queue 1815 PQ Configuration Commands CQ Configuration Commands Related commands qos cq113 Display qos cq interface Default values will not be displayed Qos cqExamples # Display information about a CQL Syntax qos cq cql cql-index Undo qos cq Qos cql default-queue Examples # Assign default queue 2 to CQLQos cql inbound-interface 1819 Qos cql protocol Descriptions of values of queue-key and key-value Qos cql queue 1821 Undo qos cql cql-indexqueue queue-numberserving Qos cql queue servingExamples # Specify byte-count of queue 2 in the CQL 5 to WFQ Configuration Commands Related commands qos wfq114 Display qos wfq interface Undo qos wfq Qos wfqDisplay interface, display qos wfq interface CBQ Configuration Commands 115Display qos cbq interface Qos max-bandwidth Queue af Queue ef 1827 Queue wfq Queue-length WredSyntax wred dscp ip-precedence Undo wred 1829 Wred dscp Undo wred dscp dscp-value Wred ip-precedence 1831 Wred weighting-constant RTP Priority Queue Configuration Commands Description on the fields of the display qos rtpq command116 Display qos rtpq interface Qos rtpq Qos rtpq Related commands qos reserved-bandwidth 1835 RTP Priority Queue Configuration Commands QOS Token Configuration Commands 117Qos qmtoken Qos qmtoken token-number QOS Token Configuration Commands Priority Mapping Table Configuration Commands Related commands qos map-tabledot1p-Ip118 Display qos map-table Related commands display qos map-table Parameters in the default mapping tableQos map-table dot1p-Ip Import 1841 Priority Mapping Table Configuration Commands Port Priority Configuration Commands 119Qos priority Undo qos priority Port Priority Configuration Commands Port Priority Trust Mode Configuration Commands 120Display qos trust interface Qos trust Port Priority Trust Mode Configuration Commands Wred Configuration Commands 121Display qos wred interface 1847 Qos wred enable Qos wred dscp ip-precedence enableUndo qos wred enable Dscp Uses the Dscp value for calculating drop probability By default, the dropping method of a queue is tail drop Related commands qos wfq, display qos wred interfaceQos wred dscp 1849 Discard-probability discard-prob Qos wred weighting-constantUndo qos wred ip-precedence ip-precedence Length, in the range 1 to 16. It defaults to Wred with the qos wred enable command on itQos wred enable, display qos wred interface Calculate the average length of Wred queues Wred Configuration Commands Wred Table Configuration Commands 122Display qos wred table Syntax display qos wred table table-name Qos wred queue table Qos wfq , qos wred enable , display qos wred interfaceQos wred apply Queue Related commands qos wred queue table in system view1855 Wred Table Configuration Commands Mpls QOS Configuration Commands 123If-match mpls-exp Qos cql protocol mpls exp Related commands qos cql protocol Qos pql protocol mpls exp Examples # Set EXP value of remarked Mpls packet to Related commands qos pql protocol1859 Mpls QOS Configuration Commands DAR Configuration Commands 124Dar max-session-count Dar protocol Protocols of pre-defined ports Protocol name Protocol type Pre-defined port number 1863 # Restore the default name of the user-defined01 protocol Dar protocol-renameDar protocol-statistic Undo dar protocol-rename user-defined-name Display dar information Undo dar protocol-statisticSyntax display dar information 1865 Display dar protocol Display dar protocol all protocol-name 1867 Display dar protocol-rename Display dar protocol-rename Display dar protocol-statistic If-match protocol If-match protocol http If-match protocol rtp Reset dar protocol-statisticUndo if-match not protocol rtp payload-type audio video Information, i.e. to restore the statistics to Reset dar sessionAll Deletes all statistics information # Deletes all statistics information DAR Configuration Commands FR QOS Configuration Commands 125Apply policy outbound # Define a traffic behavior named behavior Related commands ebs, cir allow, cir CbsCir Undo cir Related commands Cir allowCbs, ebs, cir allow Cir allow inbound outbound committed-information-rate Related commands cbs, ebs, cir Related commands fr congestion-thresholdCongestion-threshold Undo cq Display fr class-map Related commands wfq, pq, fr pvc-pq1879 Related commands fragment Display fr fragment-info # Display FR fragment information of a certain interfaces 1881 Display fr switch-table Fr switch 1883 PVC PQ on FR interface Display qos pvc-pq interface# Display PVC PQ information on FR interface Serial2/0 Ebs Related commands Cbs, cir allow, cir ExamplesFifo queue-length Related commands fr class Related commands fr-classFr class Fr congestion-threshold Fr de del Related commands congestion-threshold1887 Related commands fr de del, fr del protocol Related commands fr del inbound-interface,fr del protocolFr del inbound-interface Related commands fr de del, fr del inbound-interface Fr del protocolProtocol ip IP 1889 Fr pvc-pq Related commands pvc-pqUndo fr pvc-pq Related commands fr class, fr-class,fr dlci Fr traffic-policingFr traffic-shaping Syntax fr traffic-policing Undo fr traffic-policing Examples # Enable Frts on the serial interface Serial 1/0 FragmentFr-class Undo fragment fragment-size Related commands fr class, fr dlci Related commands cq, wfq, fr pvc-pqPvc-pq Undo pq Rtpq Undo pvc-pqFr pvc-pq Number, in the range 2000 to Traffic-shaping adaptation Related commands fr traffic-shaping,cir allow, and cirUndo traffic-shaping adaptation becn interface-congestion Related commands cq, pq, fr pvc-pq WfqUndo wfq Examples # Apply WFQ to the FR class test1 802.1X Configuration Commands Example # Display 802.1x configuration information126 Display dot1x Descriptions on the fields of the display dot1x command Dot1x Dot1x interface interface-listUndo dot1x interface interface-list Dot1x Dot1x authentication-method Related command display dot1x# Enable 802.1x globally Syntax dot1x authentication-method chap eap pap Undo dot1x authentication-method Dot1x guest-vlan Dot1x guest-vlan vlan-id Undo dot1x guest-vlan Dot1x handshake Dot1x handshakeUndo dot1x handshake Undo dot1x max-user interface interface-list Dot1x max-userDot1x max-user user-number Undo dot1x max-user Dot1x multicast-trigger By default, the multicast trigger function is enabledDot1x port-control Dot1x port-method Dot1x port-method macbased portbased Undo dot1x port-method Syntax dot1x quiet-period Undo dot1x quiet-period Dot1x quiet-period1907 Related command display dot1x, dot1x timer Dot1x retryDot1x supp-proxy-check Undo dot1x retry 1909 Dot1x timer Reset dot1x statistics Example # Set the server timeout timer to 150 secondsReset dot1x statistics interface interface-list 1911 Example # Clear 802.1x statistics on port Ethernet 1/1 AAA Configuration Commands Access-limitAccounting default 127 AAA Configuration Commands Accounting lan-access Accounting loginRelated command accounting default, radius scheme 1915 Accounting optional Undo accounting loginSyntax accounting optional Undo accounting optional Accounting portal 1917 Accounting ppp Related command domain, radius scheme Undo attribute access-limit idle-cut ip location mac vlanAccounting voip Attribute Authentication default Related command display local-userLocal Performs local authentication Example # Set the IP address of local user user1 to Authentication lan-access Undo authentication lan-accessLocal Performs local authentication None Does not perform any authentication Authentication login Related command authentication default, radius scheme Authentication portal 1923 Undo authentication ppp Authentication pppRadius-scheme radius-scheme-name local Authorization command Authentication voip1925 Authorization default Related command authorization default, hwtacacs scheme Authorization lan-access 1927 Authorization login Related command authorization default, radius scheme Authorization portal 1929 Authorization ppp Authorization voipUndo authorization ppp Authorization default , hwtacacs scheme , radius scheme Cut connection Domain , radius scheme Display connection Related command cut connection Example Description on the fields of the display connection commandDisplay domain # Display information about all AAA user connections Related command access-limit,domain, state Description on the fields of the display domain command Related command local-user Display local-user Domain # Display information about all local usersUndo domain isp-name Description on the fields of display local-user Domain default Related command access-limit,state, display domainDomain default disable enable isp-name State , display domain Idle-cut Ip poolDomain Domain aabbcc.net Related command remote address on LevelSyntax level level Undo level Related command display local-user,service-type Local-userExample # Set the level of user user1 to Example # Add a local user named user1 Password Local-user password-display-modeRelated command display local-user , password Self-service-url Service-type Service-type ftp Service-type pppRelated command service-type ppp and service-type ftp Syntax service-type ftp Undo service-type ftp State State active block Related command domain Work-directory# Place the current user user1 to the state of blocked Syntax work-directory directory-name Undo work-directory 1947 AAA Configuration Commands Radius Configuration Commands Accounting-on enable128 Radius scheme Accounting-on enable send Accounting-on enable intervalRelated command radius scheme, accounting-on enable Data-flow-format Radius scheme view GigabyteMega-packet, or giga-packet Packets to be sent to a Radius server Related command display radius scheme Related command radius schemeExample # Display the configurations of all Radius schemes Display radius scheme Display radius statistics Display radius statisticsExample # Display statistics about Radius packets 1953 State statistictotal=1024 State statistics 1955 Dead Display stop-accounting-buffer Which is a string of 1 to 32 charactersTime range, or user name On August 31 Nas-ip Radius scheme view Key Radius scheme viewDisplay radius scheme Primary accounting Radius scheme view Related command radius nas-ipUndo primary accounting Primary authentication Radius scheme view 1959 Syntax radius client enable Undo radius client Example # Enable the listening port of the Radius clientRadius client Radius nas-ip Related command nas-ip Radius scheme view Radius schemeUndo radius nas-ip Undo radius scheme radius-scheme-name Radius trap Reset radius statistics Reset stop-accounting-bufferSyntax reset radius statistics Example # Clear Radius statistics Retry Undo retry Retry realtime-accounting 1965 Secondary accounting Radius scheme view Retry stop-accounting Radius scheme viewUndo secondary accounting Secondary authentication Radius scheme view 1967 Security-policy-server Server-typeSyntax server-type extended standard Undo server-type View Radius scheme view Use the state command to set the status of a Radius server Primary Sets the status of the primary Radius serverSecondary Sets the status of the secondary Radius server Accounting Sets the status of the Radius accounting server Stop-accounting-buffer enable Radius scheme view Timer quiet Radius scheme view Timer realtime-accounting Radius scheme viewSyntax timer quiet minutes Undo timer quiet 1971 Related command retry realtime-accounting,radius scheme Timer response-timeout Radius scheme viewNumber of users Real-time accounting interval minute User-name-format Radius scheme view Related command radius scheme, retryUser-name-format with-domain without-domain Radius Configuration Commands Hwtacacs Configuration Commands Related command display hwtacacs129 Data-flow-format Hwtacacs scheme view Related command hwtacacs scheme Description on the fields of the display hwtacacs command Scheme view , retry stop-accounting Hwtacacs scheme view Hwtacacs nas-ipAddress or a loopback address Hwtacacs scheme Related command nas-ip Hwtacacs scheme viewUndo hwtacacs scheme hwtacacs-scheme-name Key accounting authentication authorization string Undo key accounting authentication authorization stringKey Hwtacacs scheme view Nas-ip Hwtacacs scheme view Related command hwtacacs nas-ip Primary accounting Hwtacacs scheme view Example # Set the primary authentication server Primary authentication Hwtacacs scheme view1981 Primary authorization Reset hwtacacs statisticsUndo primary authorization Accounting Clears Hwtacacs accounting statistics Retry stop-accounting Hwtacacs scheme view Syntax secondary authentication ip-address port-number Secondary authentication Hwtacacs scheme viewSecondary accounting Hwtacacs scheme view Example # Configure the secondary authentication server Secondary authorization1985 Example # Configure the secondary authorization server Stop-accounting-buffer enable Hwtacacs scheme viewView Hwtacacs scheme view Timer realtime-accounting Hwtacacs scheme view Timer quiet Hwtacacs scheme view1987 Timer response-timeout Hwtacacs scheme view User-name-format Hwtacacs scheme view Hwtacacs scheme Hwtacacs Configuration Commands Packet Filter Firewall Configuration Commands Switch running a routing protocolDisplay firewall ethernet-frame-filter All Displays all the firewall statistics information Firewall default Syntax firewall default permit denyDisplay firewall-statistics Fragments-inspect Firewall enable Firewall enableUndo firewall enable Firewall ethernet-frame-filter Example # Enable fragments inspection Firewall fragments-inspect Firewall fragments-inspect high low number default Firewall fragments-inspect high lowFirewall ipv6 fragments-inspect Undo firewall fragments-inspect high low Related command firewall fragments-inspect Firewall packet-filter Reset firewall ethernet-frame-filter Firewall packet-filter ipv6Outbound Undo firewall packet-filter ipv6 inbound outbound Example # Clear all the firewall statistic information Reset firewall-statistics# Clear the firewall statistic information of Ethernet 1/0 Aspf Configuration Commands 131Aging-time Aging-time syn fin tcp udp seconds # Set the UDP idle timeout period to 110 seconds # Set the TCP idle timeout period to 3000 secondsAspf-policy Syntax display aspf all Display aspf all2001 Display aspf interface Syntax display aspf interface Display aspf policy Display aspf sessionSyntax display aspf policy aspf-policy-number Display aspf session verbose Display port-mapping Related command port-mapping Firewall aspfExample # Display all the information about port mapping 2005 Log enable Syntax log enable Undo log enableExample # Enable the session logging function of the Aspf Port-mapping Reset aspf session Related command display port-mappingSyntax reset aspf session Example # Map port 3456 to the FTP protocol Aspf Configuration Commands MAC Authentication Configuration Commands Display mac-authenticationSyntax display mac-authentication interface interface-list DFIC-9FSW and MSR 20 Series Products Mac-authentication MAC Addr Mac-authentication domain 2011 Mac-authentication timer Related command display mac-authentication Mac-authentication user-name-format Reset mac-authentication statistics NAT Configuration Commands Connection-limit default actionConnection-limit default amount 133 Connection-limit enable Connection-limit enableUndo connection-limit enable Connection-limit policy Display connection-limit policy Example # Create a connection-limit policy numberedSyntax display connection-limit policy policy-numberall 2017 Display connection-limit statistics Display nat address-group Display nat address-groupView Any view Parameter None Information Display nat aging-time Display nat allDisplay nat aging-time Different NAT sessions Description on some fields of the display nat all command 2021 Display nat connection-limit Destination address Display nat log Mask-length The length of net mask, in the range 1 toSyntax display nat log 2023 # View the NAT log configuration Description on the fields of the display nat log commandDisplay nat outbound Display nat outbound Display nat session Display nat serverSyntax display nat server Example # Display the active NAT sessions Display nat statisticsSyntax display nat statistics Display userlog export Limit acl Syntax limit mode amount Undo limit mode Limit modeView Connection-limit policy view Nat address-group Nat aging-timeUndo nat address-group group-number Tcp-syn udp seconds Nat alg Nat connection-limit-policy 2031 Nat log enable Nat log flow-active Nat log flow-begin Nat outboundNat log flow-begin Undo nat log flow-begin NAT Configuration Commands # Configure the address pool Nat outbound staticNat server Syntax nat outbound static Undo nat outbound static NAT Configuration Commands 2037 # Remove the WWW server using the following commands Nat static Syntax reset nat session Reset nat session2039 Reset userlog export Reset userlog nat logbufferRelated command display userlog export Userlog nat export host Related command userlog nat export source-ip Related command userlog nat export hostUserlog nat export source-ip 2041 Userlog nat syslog Userlog nat export versionSyntax userlog nat syslog Undo userlog nat syslog PKI Configuration Commands 134 Ca identifier Syntax ca identifier name Undo ca identifier Certificate request from Certificate request entityPki entity Certificate request mode Simple password * manualUndo certificate request mode Certificate request polling Related command display pki certificate Certificate request urlUndo certificate request polling count interval 2047 Common-name CountrySyntax common-name name Undo common-name Undo country Crl update-period Crl check disable enableCrl update-period hours Undo crl update-period Display pki certificate Crl urlUndo crl url Example # Display the local certificate 2051 Display pki certificate access-control-policy Display pki certificate attribute-group Related command pki retrieval-crl domain and pki domain Display pki crl domainSyntax display pki crl domain domain-name Example # Display the locally saved CRLs Fqdn Ip PKI entity viewUndo fqdn Undo ip Ldap-server LocalityUndo ldap-server Undo locality Organizational-unit OrganizationSyntax organization org-name Undo organization Pki certificate attribute-group Pki certificate access-control-policy2057 Pki domain Pki delete-certificateSyntax pki domain domain-nameundo pki domain domain-name Pki entity Pki import-certificatePki entity entity-name Undo pki entity entity-name Related command pki domain Pki request-certificate domain Related command Pki domain Example Pki retrieval-certificatePki retrieval-crl domain Pki retrieval-certificate ca local domain domain-name Pki validate-certificate Root-certificate fingerprintPki validate-certificate ca local domain domain-name Root-certificate fingerprint md5 sha1 string Syntax rule id deny permit group-name Undo rule id all Rule access control policy view2063 Undo state Portal Configuration Commands Portal authentication135 Display portal acl Description on the fields of the display portal acl command Display portal connection statisticsAll Displays portal connection statistics on all interfaces Statistics on the specified interface 2067 Display portal free-rule Msgauthenack Msgauthorack Msgloginack MsglogoutackSyntax display portal free-rule rule-number Display portal interface Related command portal free-rule2069 Related command portal server Display portal serverSyntax display portal server server-name URL Display portal server statistics All Displays portal server statistics on all interfaces2071 Reqchallenge Display portal tcp-cheat statistics Syntax display portal tcp-cheat statistics Display portal user Specified interface enabling portalSpecified interface or all interfaces enabling portal 2073 Portal auth-network Undo portal auth-network network-addressall Related command display portal user Portal delete-userPortal free-rule Undo portal free-rule rule-numberall Related command display portal free-rule Portal resource-name Related command display portal server Portal serverUndo portal server server-name key port url 2077 Reset portal connection statistics Portal server method Reset portal tcp-cheat statistics Reset portal server statisticsReset portal tcp-cheat statistics Portal Configuration Commands 136 RSH Configuration CommandsRsh INSTALL.LOG Common Configuration Commands Description on the fields of the display time-range commandDisplay time-range Time-range Common Configuration Commands 2085 Common Configuration Commands IPV4 ACL Configuration Commands 138Acl 2087 Acl copy # Create IPv4 ACL 2002, giving the ACL a name of flow# Delete the IPv4 ACL with the number # Delete the IPv4 ACL named flow Syntax acl name acl-name Acl name2089 # Define the description of IPv4 ACL Description for IPv4# Define the description of ACL Description on the fields of the display acl command Display aclSyntax display acl acl-numberall name acl-name 2091 Reset acl counter Syntax reset acl counter acl-number all name acl-nameRule in basic IPv4 ACL view # Clear statistics about IPv4 ACL flow 2093 Rule in advanced IPv4 ACL view TCP/UDP-specific parameters for advanced IPv4 ACL rules Parameter Function Description Icmp-type Icmp message Type Code Undo rule rule-id Rule in Ethernet frame header ACL view2097 Rule in user-defined ACL view View User-defined ACL view Support to this command varies by device Rule comment for IPv4# Create a user-defined ACL rule Syntax rule rule-idcomment text Undo rule rule-idcomment Step for IPv4 # Create a rule in ACL 3000 and define the rule description# Create a rule in ACL 4000 and define the rule description # Create a rule in ACL 5000 and define the rule description Example # Set the rule numbering step to 2 for ACL 2101 IPV4 ACL Configuration Commands IPV6 ACL Configuration Commands 139Acl ipv6 2103 Acl ipv6 copy # Create IPv6 ACL 2002, giving the ACL a name of flow# Delete the IPv6 ACL with the number # Delete the IPv6 ACL named flow Syntax acl ipv6 name acl6-name Acl ipv6 name2105 Description for IPv6 Display acl ipv6# Create a description for IPv6 ACL Syntax display acl ipv6 acl6-numberall name acl6-name Reset acl ipv6 counter All All basic and advanced IPv6 ACLs2000 to 2999 for basic IPv6 ACLs 3000 to 3999 for advanced IPv6 ACLs # Clear the statistics about the IPv6 ACL named flow Rule in basic IPv6 ACL viewUndo rule rule-id fragment logging source time-range Rule in advanced IPv6 ACL view 2109 Destination dest Parameter Function Description Source sourceTime-range time-name ICMPv6-specific match criteria for advanced IPv6 ACL rules TCP/UDP-specific match criteria for advanced IPv6 ACL rulesAvailable ICMPv6 messages Rule in simple IPv6 ACL view View Simple IPv6 ACL view Parameters for simple IPv6 ACL rules ICMPv6-specific parameters for simple IPv6 ACL rules TCP/UDP-specific parameters for simple IPv6 ACL rulesICMPv6 messages definable in simple IPv4 ACL rules Rule comment for IPv6 Support for this command varies by device2115 Step for IPv6 Example # Set the rule numbering step to 2 for IPv6 ACL # Set the rule numbering step to 2 for IPv6 ACL 2117 IPV6 ACL Configuration Commands Ipsec Configuration Commands Ah authentication-algorithmCryptoswitch fabric enable 140 Display encrypt-card fast-switch Syntax display encrypt-card fast-switch Display ipsec policy brief name policy-name seq-number Display ipsec policyIpsec policy system view # Display detailed information about all IPSec policies Display ipsec policy-template IPSec policy template group10000 Template group Related command ipsec proposal Display ipsec proposalDisplay ipsec sa Syntax display ipsec proposal proposal-name Reset ipsec sa, ipsec sa global-duration Description on the fields of the display ipsec sa command Related command reset ipsec session Display ipsec sessionSyntax display ipsec session tunnel-id integer Example # Display information about all IPSec sessions Related command reset ipsec statistics Display ipsec statisticsSyntax display ipsec statistics Example # Display IPSec packet statistics Syntax display ipsec tunnel Display ipsec tunnel2129 Encrypt-card fast-switch Encapsulation-mode Esp authentication-algorithm Related command display encrypt-cardfast-switchEsp encryption-algorithm Syntax esp encryption-algorithm 3des aes key-length des Undo esp encryption-algorithm Ike-peer IPSec policy view/IPSec policy template viewSyntax ike-peer peer-name Undo ike-peer peer-name Ipsec binding policy Related command ipsec policy-template2133 Ipsec cpu-backup Syntax ipsec cpu-backup enable Undo ipsec cpu-backup enable Ipsec policy interface view 2135 Ipsec policy system view Syntax ipsec policy policy-nameseq-number isakmp manual Ipsec policy isakmp template Ipsec policy-templateUndo ipsec policy-template template-name seq-number 2137 Related command display ipsec proposal Related command display ipsec policy-templateIpsec proposal Related command sa duration, display ipsec sa duration Ipsec sa global-durationIpsec session idle-time Example # Create an IPSec proposal named newprop1 Pfs Undo ipsec session idle-timePfs dh-group1 dh-group2 dh-group5 dh-group14 Undo pfs Example # Enable and configure PFS for IPSec policy policy1 Related command ipsec proposal, ipsec policy system viewProposal Undo proposal proposal-name Reset ipsec sa Reset encrypt-card fast-switchSyntax reset encrypt-card fast-switch Related command display ipsec sa Reset ipsec sessionSyntax reset ipsec session tunnel-id integer Reset ipsec statistics Sa authentication-hexRelated command display ipsec session Syntax reset ipsec statistics View IPSec policy view/IPSec policy template view Sa duration2145 Sa encryption-hex Sa spi 2147 Sa string-key Example # Configure IPSec policy policy1 to reference ACL Security aclSyntax security acl acl-number Undo security acl 2149 Example # Configure IPSec proposal prop1 to use AH TransformTunnel local Syntax transform ah ah-esp esp Undo transform Tunnel remote 2151 Example # Set the remote address of the IPSec tunnel to 141 IKE Configuration CommandsIke proposal, display ike proposal Related command ike proposal, display ike proposal Certificate domainDh group1 group2 group5 group14 Undo dh Related command ike dpd Display ike dpdExample # Specify 768-bit Diffie-Hellman for IKE proposal Syntax display ike dpd dpd-name Related command ike peer system view Display ike peerDisplay ike proposal Syntax display ike peer peer-name Example # Display the settings of IKE proposals Related command ike proposal, ike peer system viewDisplay ike sa 2157 # Display detailed information about the current IKE SAs 2159 Undo dpd DpdEncryption-algorithm 3des-cbc aes-cbc key-length des-cbc Exchange-mode Related command Id-type ExampleId-type Ike dpd Ike local-nameExample # Use the ID type of name in IKE negotiation Syntax ike dpd dpd-name Undo ike dpd dpd-name Ike next-payload check disabled Related command remote-name,id-typenameExample # Configure the local gateway name as app 2163 Related command display ike proposal Ike peer system viewIke proposal Syntax ike peer peer-name Undo ike peer peer-name Ike sa keepalive-timer interval Ike sa keepalive-timer timeoutRelated command ike sa keepalive-timer timeout Example # Set the keepalive interval to 200 seconds Ike sa nat-keepalive-timer interval Related command ike sa keepalive-timer intervalExample # Set the keepalive timeout to 20 seconds Interval-time Local Local-address Nat traversal Syntax nat traversal Undo nat traversalPeer multi-subnet single-subnet Undo peer Related command authentication-algorithmon Pre-shared-keyRemote-address Syntax pre-shared-key key Undo pre-shared-key Reset ike sa Related command id-typeip, local-addressRelated command id-type,ike local-name Remote-name Related command display ike sa Example # Clear the IPSec tunnel toSyntax sa duration seconds Undo sa duration 2171 Time-out Related command ike proposal and display ike proposalSyntax time-out time-out Undo time-out SSH2.0 Configuration Commands 142Display public-key local Public-key local create Example Display public-key peer Display public-key peer brief name publickey-nameBrief Displays brief information about all public keys Specified or all public keys Related command sftp client source Display sftp client source# Display brief information about all public keys Syntax display sftp client source Related command ssh client source Display ssh client sourceDisplay ssh server Syntax display ssh client source Display ssh server-info # Display the session information of the SSH serverSyntax display ssh server-info 2177 Related command ssh user Display ssh user-informationSyntax display ssh user-information username Example # Display information about all SSH users Related command Public-key peer Example Peer-public-key endPublic-key-code begin Peer-public-key end Public-key-code end Public-key local createPublic-key-code end Public-key peer, public-key-code begin Public-key local destroy Public-key local destroy, display public-key local Example# Create local RSA key pair # Create local DSA key pair Related command public-key local create Public-key local export rsaPublic-key local export rsa openssh ssh1 ssh2 filename Public-key local create , public-key local destroy Public-key local export dsa # Display the RSA local public key in OpenSSH formatPublic-key local export dsa openssh ssh2 filename # Export the DSA local public key in OpenSSH format Related command public-key-code begin, public-key-code end Public-key peer# Display the DSA local public key in OpenSSH format Syntax public-key peer keyname Undo public-key peer keyname Sftp Public-key peer import sshkey2185 Undo sftp client ipv6 source Sftp client ipv6 sourceIpv6 ipv6-address Specifies a source IPv6 address Sftp client source Related command Display sftp client source ExampleSftp ipv6 Sysname sftp ipv6 Input Username Sftp server enable Sftp server idle-timeoutSyntax sftp server enable Undo sftp server enable Related command display ssh server Ssh client authentication server Ssh client first-time enable To access the SSH server Ssh client ipv6 sourceSsh client source Undo ssh client ipv6 source Ssh server authentication-retries Related command display ssh client source Ssh server authentication-timeout Ssh server compatible-ssh1x enableBy default, the authentication timeout period is 60 seconds Example # Enable the SSH server to work with SSH1.x clients Syntax ssh server enable Undo ssh server enable Ssh server enableSsh server rekey-interval Undo ssh user username Ssh user2195 Related command display ssh user-information Ssh2 Ssh2 ipv6 2197 SSH2.0 Configuration Commands 2199 SSH2.0 Configuration Commands Sftp Configuration Commands 143Bye Syntax bye Cdup DeleteDir Syntax cdup Exit GetSyntax exit 2203 Help Put Mkdir2205 Pwd QuitSyntax pwd Syntax quit Remove RenameRmdir 2207 Sftp-client rmdir temp1 Directory successfully removed SSL Configuration Commands 144Ciphersuite View SSL server policy view Client-verify enable Syntax client-verify enable Undo client-verify enableExample # Set the SSL connection close mode to wait Close-mode wait Display ssl client-policy Display ssl server-policySyntax display ssl client-policy policy-nameall Syntax display ssl server-policy policy-nameall Handshake timeout Syntax handshake timeout time Undo handshake timeoutPki-domain Syntax pki-domain domain-name Prefer-cipher Undo pki-domainUndo prefer-cipher 2213 Session cachesize size timeout time Undo session cachesize timeoutSession Rsaaes128cbcsha Ssl server-policy Ssl client-policy2215 Use the undo version command to restore the default Version ssl3.0 tls1.0SSL client policy view Ssl3.0 Specifies SSL Display standby flow Backup Center Configuration CommandsSyntax display standby flow Main and backup interfaces Display standby stateDisplay standby state Following tables describe the meanings of each state Backup states of the backup interface Backup flagsStandby bandwidth Syntax standby bandwidth size Undo standby bandwidth Related command standby interface Standby interface Related commands standby track Standby thresholdUndo standby threshold 2221 Related command standby interface and standby bandwidth Standby timer delayUndo standby timer delay Standby timer flow-check Standby trackUndo standby track 2223 Standby interface, track on IPV4-BASED Vrrp Configuration Commands Display vrrp Description on the fields of the display vrrp command Vrrp vrid track interface commandVrrp vrid track command Display vrrp statistics Example # Display the statistics about all standby groups 2227 Reset vrrp statistics Vrrp vrid authentication-mode255 Device are cleared Syntax vrrp method real-mac virtual-mac Undo vrrp method Vrrp method2229 Vrrp ping-enable Vrrp ping-enableUndo vrrp ping-enable Addresses of standby groups Default mode is immediate preemption without delay Vrrp un-check ttlVrrp vrid preempt-mode Syntax vrrp un-check ttl Undo vrrp un-check ttl Vrrp vrid priority Vrrp vrid track Vrrp vrid timer advertise2233 Vrrp vrid track interface Vrrp vrid virtual-ip 2235 # Add virtual IP address 10.10.10.11 to standby group Vrrp Configuration Commands For IPV6 147Display vrrp ipv6 IPv6 Vrrp ipv6 vrid track command Display vrrp ipv6 statistics 2239 Vrrp ipv6 method Reset vrrp ipv6 statisticsSyntax vrrp ipv6 method real-mac virtual-mac Vrrp ipv6 ping-enable Vrrp ipv6 ping-enableUndo vrrp ipv6 ping-enable Undo vrrp ipv6 method Vrrp ipv6 vrid authentication-mode Vrrp ipv6 vrid preempt-mode Undo vrrp ipv6 vrid virtual-router-idpriority Vrrp ipv6 vrid priority2243 Vrrp ipv6 vrid timer advertise Undo vrrp ipv6 vrid virtual-router-idtimer advertise Vrrp ipv6 vrid track 2245 # Configure the virtual IPv6 address of standby group 1 as Vrrp ipv6 vrid virtual-ip Device Management Commands 148 Bootrom Buzzer enableSyntax buzzer enable Undo buzzer enable Part Display boot-loader This command is applicable on MSR 50 series routers onlyDisplay boot-loader slot slot-number Related command Boot-loader Display cpu-usage Display cpu-usage task number offset verbose from-device Description on fields of the display boot-loader command Display deviceSyntax display device cf-card usb slot slot-numberverbose 2251 Cf-card Displays information of a compact Flash CF Usb Displays information of a universal serial bus USBVaries with devices Such as card, CF, USB, VCPM, VPM and DSP 2253 Description on fields on the display device commandCpld Display device manuinfo Display device manuinfo slot slot-numberInformation about the device Display # Display the temperature information of cards Display environmentExample # Display manufacturing information of a device Display environment Display fan Display licenseDisplay fan fan-id Display license Display power Syntax display power power-idDisplay memory Syntax display memory Display reboot-type Display schedule rebootDisplay reboot-type slot slot-number Display schedule reboot Reboot Only users at management level can execute this commandReboot slot slot-number License register Reset unused porttag Use the remove command to remove a cardSyntax reset unused porttag Remove slot slot-number Syntax schedule reboot at hhmm date Undo schedule reboot Schedule reboot at2261 Schedule reboot delay Syntax schedule reboot delay hhmm mm Undo schedule reboot Temperature-alarm enable 2263 Temperature-limit Undo temperature-limit slot-number Data-fill NQA Client Configuration CommandsSyntax data-fill string Undo data-fill Description any NQA test type view Data-sizeSyntax data-size size Undo data-size Destination ip Destination portSyntax destination ip ip-address Undo destination ip Syntax destination port port-number Undo destination port Syntax display nqa result history admin-nameoperation-tag Display nqaResult Displays the results of the last test History Displays the history records of a test Description on the fields of the display nqa result command 2269 # Display the history records of tests Field Description Index History record number Filename FrequencySyntax filename filename Undo filename Syntax frequency interval Undo frequency History-records Syntax history-records number Undo history-records Http-version Next-hopHttp-version Undo http-version Nqa agent enable Syntax nqa agent enable Undo nqa agent enableRelated command nqa server enable Nqa Example # Enable the NQA client Nqa agent max-concurrentNqa schedule 2275 Operation FTP test type view Operation Http test type viewOperation get put Undo operation Password FTP test type view Syntax password password Undo passwordOperation interface Undo operation interface Probe count Syntax probe count times Undo probe count Probe packet-number Probe packet-interval2279 Probe timeout Probe packet-timeoutSyntax probe timeout timeout Undo probe timeout Reaction 2281 Route-option bypass-route Reaction trapUndo reaction trap probe-failure test-complete test-failure Related command source ip Source interfaceUndo source interface 2283 Related command source interface Source ipSource port Syntax source ip ip-address Undo source ip Tos TtlSyntax tos value Syntax ttl value Type Url Username FTP test type viewSyntax url url Undo url Vpn-instance ICMP-echo test type view Syntax vpn-instance instance Undo vpn-instance NQA Server Configuration Commands 150Display nqa server status Syntax display nqa server status Nqa server enable Syntax nqa server enable Undo nqa server enableRelated command nqa server tcp-connect,nqa server udp-echo Example # Enable the NQA server Undo nqa server udp-echo ip-addressport-number Nqa server udp-echo2291 Sysname nqa server udp-echo 169.254.10.2 Display ip netstream cache Netstream Configuration CommandsSyntax display ip netstream cache Ip netstream statistics command Display ip netstream exportDisplay ip netstream export Exported NetStream UDP packets Enable Syntax enableUndo enable Related command ip netstream aggregation Ip netstream aggregation Source-prefix Ip netstream export host Ip netstream export sourceExample # Enter NetStream AS aggregation view 2297 Ip netstream export version Ip netstream timeout active Related command ip netstream timeout inactiveIp netstream max-entry 2299 Ip netstream timeout inactive Reset ip netstream statisticsRelated command ip netstream timeout active Reset ip netstream statistics NTP Configuration Commands Display ntp-service sessionsSyntax display ntp-service sessions verbose 152 Display ntp-service status Display ntp-service statusExample # View the NTP service status information Syntax display ntp-service trace Display ntp-service trace2303 Ntp-service access Undo ntp-service access peer query server synchronizationProtection. a more secure method is identity authentication Sure you have already created and configured this ACL Ntp-service authentication enable Ntp-service authentication-keyidBy default, NTP authentication is disabled # Enable NTP authentication Ntp-service broadcast-client Ntp-service broadcast-server Ntp-service in-interface disable 2307 Ntp-service max-dynamic-sessions Ntp-service multicast-client Ntp-service multicast-server Ntp-service refclock-masterUndo ntp-service multicast-server ip-address 2309 Ntp-service reliable authentication-keyid Ntp-service source-interfaceUndo ntp-service source-interface Used as a reference clock Ntp-service unicast-peer Vpn-instance-name in your command Ntp-service unicast-serverPublic network No NTP server is designated for the device by default Designated for the deviceInterface and the NTP server coexist in this VPN 2313 NTP Configuration Commands Rmon Configuration Commands Display rmon alarmSyntax display rmon alarm entry-number Related command rmon alarm Related command rmon event Example # Display the configuration of Rmon event tableDescription on the fields of the display rmon event command Display rmon event Display rmon eventlog Display rmon historySyntax display rmon eventlog entry-number 2317 Related command rmon history Display rmon prialarm Syntax display rmon prialarm entry-numberRelated command rmon prialarm Current-configuration and display this commands you cannot With the display current-configuration and display Related command rmon statisticsDisplay rmon statistics Undo rmon alarm entry-number Rmon alarm2321 You can create up to 60 alarm entries Table with the rmon event commandRising alarm and falling alarm are alternate Rmon event You can create up to 100 alarm entries Rmon historyUndo rmon history entry number Display rmon history Undo rmon prialarm entry-number Rmon prialarm2325 You can create up to 50 pri-alarm entries Configurations the same and the creation fails# Remove private alarm entry Rmon statistics 2327 Rmon Configuration Commands Snmp Configuration Commands Display snmp-agent local-switch fabricid154 Display snmp-agent community Syntax display snmp-agent group group-name Display snmp-agent groupDescriptions on the fields of display snmp-agent community Name of the specified MIB view Display snmp-agent mib-view2331 Display snmp-agent statistics Syntax display snmp-agent statistics Display snmp-agent sys-info Display snmp-agent sys-info contact location versionVersion Displays the version of the current Snmp agent 2333 Display snmp-agent trap-list Related command snmp-agent trap enableSyntax display snmp-agent trap-list Enable snmp trap updown Syntax enable snmp trap updown Undo enable snmp trap updownDisplay snmp-agent usm-user # Display SNMPv3 information for the user aa Snmp-agent Snmp-agentUndo snmp-agent Snmp-agent community Undo snmp-agent community community name Undo snmp-agent group v3 group-name authentication privacy Related command snmp-agentmib-view,snmp-agentusm-userSnmp-agent group Undo snmp-agent group v1 v2c group-name Snmp-agent log Snmp-agent local-switch fabricidSnmp-agent usm-user Snmp-agent mib-view Undo snmp-agent mib-view view-name Related command snmp-agent group Snmp-agent packet max-sizeSnmp-agent sys-info 2341 Related command Display snmp-agentsys-info Snmp-agent target-host 2343 Snmp-agent trap enable Linkup warmstart * system voice vrrp authfailure newmaster Snmp-agent trap if-mib link extended Snmp-agent trap if-mib link extendedUndo snmp-agent trap if-mib link extended NMS, the device may not be able to resolute the messages Snmp-agent trap life Snmp-agent trap queue-size Example # Configure the size of the Trap queue to Snmp-agent trap sourceSnmp-agent usm-user Undo snmp-agent trap source Parameter v1 SNMPv1 2349 Snmp Configuration Commands File System Configuration Commands Copy Syntax delete /unreserved file-url Syntax dir /all file-url Syntax execute filename Execute2353 File prompt FixdiskFile prompt alert quiet Syntax fixdisk device Format Syntax format device# create a subdirectory named mytest under test 2355 More MountSyntax more file-url Syntax mount device Related command Example Umount Move# Mount a CF card on a centralized device 2357 Reset recycle-bin Syntax reset recycle-bin /forceExample # Move the file cf/test/sample.txt to cf/sample.txt Example # Rename the file sample.txt as sample.bak Syntax umount device Umount2359 Related command mount UndeleteExample # Unmount a CF card on a device Syntax undelete file-url Configuration File Management Commands Backup startup-configurationDisplay saved-configuration Syntax display saved-configuration by-linenum Configuration File Management Commands Reset saved-configuration Related command startup saved-configurationReset saved-configuration backup main Display startup Restore startup-configuration Related command save, display saved-configuration Save Syntax save file-name safely backup main2365 Startup saved-configuration Related command display startup 2367 Configuration File Management Commands FTP Server Configuration Commands Related command ftp timeout and ftp update157 Display ftp-server Ftp server enable Syntax ftp server enable Undo ftp serverDescription on the fields of the display ftp-user command Free ftp user Ftp timeout Ftp updateSyntax ftp timeout minute Undo ftp timeout Syntax ftp update fast normal Undo ftp update Sysname system-view Sysname ftp update normal FTP Client Configuration Commands 158Ascii Binary Syntax cd pathname Close DebuggingSyntax close Syntax debugging Undo debugging Description on the fields of the debugging command View FTP client view Parameter remotefile File name # View the content of aa.txt DisconnectSyntax disconnect 2377 Display ftp client configuration Syntax display ftp client configurationRelated command ftp client source Ftp Ftp client source Ftp client sourceUndo ftp client source Related command display ftp client configuration Ftp ipv6 2381 Lcd Syntax lcd Open # View the content of file aa.txt2383 Related command close Open ipv6 Passive Syntax passiveUndo passive 2385 Parameter protocol-command FTP command Remotehelp Description on the fields of the remotehelp command # Display the help information for the user command2387 Nlst SiteSyst Stat Verbose Syntax verboseUndo verbose 2389 FTP Client Configuration Commands Tftp Client Configuration Commands Display tftp client configuration159 Tftp-server acl Tftp # Associate IPv6 ACL 2001 with Tftp application in Ipv6 Related command tftp client source IP address configured on the deviceTftp client source On the source interface, the transmission fails Related command display tftp client configuration Tftp ipv6 2395 Tftp Client Configuration Commands 160 System Maintaining CommandsPing Ping ipv6 2399 Tracert Range 1 to 65535, defaulting to 65535, in milliseconds. The default value is 5000 msTracert ipv6 With IPv6 address System Maintaining Commands System Debugging Commands 161Undo debugging all module-name option View User view Parameter all All debugging functions Display debugging Related command display debuggingDebugging Basic Configuration Commands 162Clock datetime Clock summer-time one-off Basic Configuration Commands Clock summer-time repeating 2407 Clock timezone Command-privilege Command-privilege level level view view commandUndo command-privilege view view command Display clock Configure-user count Description Related commandDisplay configure-user Display clipboard Display configure-user Syntax display configure-userDisplay clock Syntax display clock Related command configure-user count Display current-configurationExclude text Special characters in regular expression 2413 Display diagnostic-information # Display the configuration beginning with userDisplay diagnostic-information Version, display device, display current-configuration Display history-command Syntax display history-commandDisplay hotkey Display hotkey Display this Syntax display this by-linenum Syntax display version Display version2417 Undo header incoming legal login motd shell Header incoming legal login motd shell textHeader Hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu command Ctrl+G corresponds to display current-configurationHotkey Undo hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu # Display the configuration of hotkeys Related command quit ReturnSuper Syntax return Super password Related command super passwordSuper password level user-level simple cipher password Undo super password level user-level # Display the password for switching user-level SysnameSyntax sysname sysname Undo sysname 2423 Related command quit, return System-viewSyntax system-view Example # Enter system view from the current user view Information Center Configuration Commands Description on the fields of the display channel commandDisplay channel Example # Display information for channel Display info-center Syntax display info-center Description on the fields of the display info-center command 2427 Display logbuffer Represents information level, in the range 0 toSeverity description Meanings of characters in text Rest is omitted here Descriptions on the fields of the display logbuffer command2429 Display logbuffer summary Display logfile bufferDisplay logbuffer summary level severity Syntax display logfile buffer Support for the command varies with devices Example # Display the contents of the log file bufferDisplay logfile summary Syntax display logfile summary Display trapbuffer Info-center channel nameDisplay trapbuffer size buffersize Trap buffer, in the range 1 to 1,024 Info-center console channel 2433 Info-center enable Syntax info-center enable Undo info-center enableInfo-center logbuffer Undo info-center logbuffer channel size Info-center logfile enable Example # Enable the log file featureInfo-center logfile frequency 2435 Syntax info-center logfile switch-directory dir-name Info-center logfile switch-directoryInfo-center logfile size-quota Info-center loghost # Set the directory to save the log file to cf/testUndo info-center loghost host-ip 2437 Info-center loghost source Undo info-center loghost source Info-center monitor channel Info-center snmp channelUndo info-center snmp channel 2439 Info-center source Default output rules for different output directions Output Modules Enabled Direction Allowed Disabled Severity2441 NMS Info-center synchronous Info-center timestamp Info-center timestamp loghost date no-year-date none Info-center timestamp loghostUndo info-center timestamp loghost Info-center trapbuffer Logfile saveUndo info-center trapbuffer channel size Syntax logfile save Reset trapbuffer Reset logbufferTerminal debugging Undo terminal debugging Terminal loggingSyntax terminal logging Undo terminal logging Terminal monitor Terminal trapping Sysname terminal trapping Current terminal trapping is on User Interface Configuration Commands Acl ipv6 acl-number inbound outboundUndo acl ipv6 acl-number inbound outbound Acl acl-number inbound Activation-key Syntax activation-key character Undo activation-key Auto-execute command 2451 None Performs no authentication Password Performs local password authenticationAAA, refer to AAA Configuration Commands on Users log onto the device using the current user interface Databits 5 6 7 DatabitsUndo databits History-commandmax-size Display history-commandDisplay user-interface # Display summary about all user interfaces 2455 Description on the fields of the display users command Display usersDisplay users all All Displays information about users on all user interfaces Syntax escape-key default character Undo escape-key Escape-keyExample # Define a as the escape key 2457 None Syntax free user-interface num1 aux console tty vty num2 Free user-interface2459 # Terminate the connection with user interface VTY History-command max-sizeView User interface view Password next time you enter the system LockLock Operating under the active user interface Only, and cannot be applied to the Console port Example # Set the answering mode to auto-answer Example # Set the timeout interval to 50 secondsParity Syntax parity even mark none odd space Undo parity Example # Enable the VTYs 0 through 4 to support SSH only Protocol inboundExample # Perform odd parity check on the AUX interface Syntax protocol inbound all pad ssh telnet Redirect enable Redirect enableUndo redirect enable Redirect disconnect Related command telnet, display tcp statistics on Redirect listen-portRedirect refuse-negotiation Redirect listen-port port-number Redirect return-deal from-telnet Redirect return-deal from-telnetUndo redirect return-deal from-telnet Redirect timeout Redirect return-deal from-terminal Screen-length SendSyntax screen-length screen-length Undo screen-length Syntax send all num1 aux console tty vty num2 Set authentication password cipher simple password Set authentication passwordUndo set authentication password Related command authentication-mode ShellSyntax shell Undo shell Speed in user interface view Stopbits Terminal type User privilege level Syntax user privilege level level Undo user privilege level User-interface # Enable user 1 to access level 3 commands# Enter the user interface view of VTY 0 to User Interface Configuration Commands MAC Address Table Management Configuration Commands Display mac-addressEthernet interfaces Display mac-address blackhole vlan vlan-id count Display mac-address aging-time Display mac-address mac-learningSyntax display mac-address aging-time Port Index Mac-address Ethernet interface view 2479 Related command display mac-address Mac-address system viewBlackhole MAC address entries are dropped Specified Vlan ID, in the range 1 to Mac-address mac-learning disable 2481 Example # Disable global MAC address learning Related command display mac-addressmac-learningMac-address max-mac-count Ethernet interface view Mac-address timer aging seconds no-aging Mac-address timerUndo mac-address timer aging MAC Address Table Management Configuration Commands 166 POE Configuration CommandsApply poe-profile Module, and slot of the power sourcing equipment PSE Description on fields of the display poe device commandDisplay poe device Display poe interface 2487 Description on fields of the display poe interface command # Display the state of all PoE interfaces Display poe interface power 2489 # Display the power information of all PoE interfaces Display poe power-usageSyntax display poe power-usage Syntax display poe pse pse-id Display poe pse2491 Syntax display poe-power Display poe-powerDescription on fields of the display poe pse command Description on fields of the display poe-power command 2493 Existing PoE configuration files will be displayed Display poe-profileDisplay poe-profile index index name profile-name Number ranges from 1 to Description on fields of the display poe-profile command 2495 Poe disconnect Display poe-profile interfaceSyntax poe disconnect ac dc Undo poe disconnect Poe enable Syntax poe enable Undo poe enable Poe enable pse Poe legacy enable Poe max-power Poe max-power system viewSyntax poe max-power max-power Undo poe max-power 2499 Poe mode Related command poe priority system viewPoe mode signal spare Undo poe mode Poe pd-description Poe pd-policy prioritySyntax poe pd-description string Undo poe pd-description Syntax poe pd-policy priority Undo poe pd-policy priority Poe priority Syntax poe priority critical high low Undo poe priority Poe priority critical high low pse pse-id Poe priority system viewUndo poe priority pse pse-id Poe update Poe update full refresh filename pse pse-idPoe pse-policy priority Poe pse-policy priority Example # Set the power alarm threshold of PSE 2 to 90% Poe utilization-thresholdPoe-profile Undo poe utilization-threshold pse pse-id Sysname system-view Sysname poe-profile abc Oap connect slot OAP Module Configuration CommandsSyntax oap connect slot slot-number Oap reboot slot Syntax oap reboot slot slot-number Acfp Configuration Commands Acfp enable168 Display acfp client-info Display acfp policy-info Client-idis the Acfp client ID, in the range of 1 toPolicy-index Policy index, in the range of 1 to Interface-numberis the interface type and interface number 2511 Display acfp rule-cache Interface type and interface numberInterface-number is the interface type and interface number Will display all the Acfp rule cache information Display acfp rule-info Interface numberClient-id Acfp client ID, in the range of 1 to 2513 # Display Acfp rule information in order of policy Establish Syntax display acfp server-info Display acfp server-info2515 Reset acfp rule-cache Type and interface number Acsei Server Configuration Commands Acsei server enableSyntax acsei server enable Undo acsei server enable Acsei server Acsei timer monitor Acsei timer clock-syncSyntax acsei timer monitor seconds Undo acsei timer monitor Acsei client close Acsei client rebootDisplay acsei client summary # Display the summary of all Acsei clients Display acsei client infoSyntax display acsei client info client-id # Display information about all Acsei clients 2521 CPU information of the Acsei client Acsei Client Configuration Commands Acsei-client debug disableAcsei-client debug enable 170 Chkconfig acseid off Syntax chkconfig acseid offAcsei-client debug show Syntax acsei-client debug show Chkconfig acseid on Service acseid condrestartSyntax chkconfig acseid on Syntax service acseid condrestart Service acseid reload Service acseid restartService acseid reload # Load the Acsei client configuration file Service acseid start Service acseid statusSyntax service acseid start Syntax service acseid status Service acseid stop Service acseid stopAny directory of the Linux system # Stop an Acsei client that is running Track Configuration Commands Description on the fields of the display track command171 Display track Track Configuration Commands 172 IPX Configuration CommandsDisplay ipx interface Display ipx routing-table Syntax display ipx routing-table network Syntax display ipx routing-table network verbose Display ipx routing-table verbose2533 Display ipx routing-table protocol Display ipx service-table Inactive Displays inactive service informationDisplay ipx routing-table statistics To 47 characters Display ipx statistics # Display detailed IPX service informationSyntax display ipx statistics 2537 SAP Ipx enable Ipx enable node nodeUndo ipx enable Configuration Ipx netbios-propagation Syntax ipx netbios-propagation Undo ipx netbios-propagationIpx encapsulation Ipx encapsulation dot2 dot3 ethernet-2 snap Ipx network Ipx rip import-route staticUndo ipx network Ipx rip import-route static Example # Enable static route redistribution to RIP Ipx rip mtuIpx rip multiplier Syntax ipx rip mtu bytes Undo ipx rip mtu Ipx rip timer update Related command ipx rip timer updateRelated command ipx rip multiplier Example # Specify a RIP update interval of 30 seconds Ipx route load-balance-path 2543 Syntax ipx sap disable Undo ipx sap disable Ipx sap disableIpx route max-reserve-path Ipx sap gns-disable-reply Ipx sap gns-disable-replyUndo ipx sap gns-disable-reply Ipx sap gns-load-balance Related command ipx sap gns-disable-reply Ipx sap max-reserve-serversIpx sap mtu Syntax ipx sap mtu bytes Related command ipx sap timer update Ipx sap multiplierUndo ipx sap mtu 2547 Ipx sap timer update Ipx serviceRelated command ipx sap multiplier, ipx update-change-only Example # Specify the SAP updating interval as 300 seconds Ipx split-horizon Ipx tickIpx split-horizon Undo ipx split-horizon Syntax ipx update-change-only Undo ipx update-change-only Ipx update-change-onlyPing ipx Reset ipx statistics Reset ipx routing-table statistics protocolSyntax reset ipx statistics 2551 Example # Display IPX routing statistics Related command display ipx routing-table statistics# Clear IPX static route statistics Voip Configuration Commands 173 Area Area-idArea custom europe north-america Undo area Related command match-template,address, and entity Busytone-t-thSyntax busytone-t-th time-threshold Undo busytone-t-th 2555 Cid display Cid receiveSyntax cid display Undo cid display Syntax cid receive Undo cid receive Cid send Cid typeSyntax cid send Undo cid send View FXS/FXO voice subscriber line view Cng-on Undo cid typeSyntax cng-on Undo cng-on Related command line and vad-on CompressionView POTS/VoIP/VoFR entity view 2559 Relationship between algorithms and bandwidth Codec Bandwidth Voice quality 711 algorithm A-law and µ-law 723 r63 algorithm723 r53 algorithm 726 r16 algorithm 726 r32 algorithm 726 r24 algorithm726 r40 algorithm Algorithm Compression efficiency of IPHC+PPP header Cptone country-type Syntax cptone country-type locale Undo cptone country-typeRegions are supported Countries or regions with supported call progress tones 2565 IEU Cptone tone-type Effect on all voice interfaces of all cards on the deviceSpecial-dial-tone waiting-tone amplitude value Special-dial-tone waiting-tone amplitude Default entity compression G729r8 Default entity payload-size Related command compression Default entity vad-on Default entity vad-onUndo default entity vad-on Vad-on Delay hold Default subscriber-lineTransmit gain Delay rising Delay send-dtmfRelated command em-signal Syntax delay rising milliseconds Undo delay rising Delay send-wink Syntax delay send-wink milliseconds Undo delay send-wink Delay wink-hold Delay wink-risingSyntax delay wink-hold milliseconds Undo delay wink-hold 2573 Syntax delay start-dial seconds Undo delay start-dial Delay start-dialDescription voice entity view Description voice subscriber line view Dial-programSyntax dial-program View Voice view Display voice call-info Display voice call-info brief mark tag verboseRange of 0 to Information table Display voice cmc LGS Display voice default all Syntax display voice default allDescription on fields of the display voice cmc command 2579 Description on fields of the display voice default command Display voice entity command Example Display voice entityDisplay voice ipp statistic Display voice entity all mark entity-tag pots voip Voip Configuration Commands Error Displays all the error statistics of IVA module Display voice iva statisticCall Displays the calling statistics in the IVA module 2583 Display voice subscriber-line Related command subscriber-lineSyntax display voice subscriber-line line-number 2585 = Busytone CNG Dscp media Dtmf amplitudeSyntax dscp media dscp-value Undo dscp media Syntax dtmf amplitude value Undo dtmf amplitude Dtmf sensitivity-level Dtmf timeDtmf time interval persist milliseconds Undo dtmf time interval persist Dtmf threshold Meaning of the index numbers2589 Index Meaning Value range Remarks Upper limit of the maximum To 4,999, with Echo-canceller 2591 Echo-canceller parameter Related command subscriber-lineand echo-canceller parameterMix-proportion-ratio value talk-threshold value Mix-proportion-ratio talk-threshold Related command echo-canceller Em-signalEm-phy-parm Entity entity-number pots voip EntityUndo entity entity-numberall pots voip Related command Line Example Related command outband, tunnel-on, and voip called-startFast-connect Fast-connect Hookoff-mode delay bind Example # Enable fast connection for VoIP voice entitySyntax hookoff-mode delay immediate Undo hookoff-mode Hookoff-mode Private-lineand caller-permitcommands when executing Hookoff-timeIncoming calls Syntax hookoff-time time Undo hookoff-time Impedance Line Match-templateUndo line Syntax match-template match-string Undo match-template Them If you want to use and at the same time, you must use themFormat . Other formats, such as and are illegal Such as 0-9. The formats like 0-A are illegal Command, but analog voice subscriber lines do not Nlp-onE1 voice, T, #, and * are not supported currently Nlp-on Outband Related command Fast-connectand tunnel-on ExamplePayload-size Syntax plc-mode general specific Undo plc-mode Plc-mode2603 Receive gain Related command transmit gain and subscriber-lineSyntax receive gain value Undo receive gain Register-number Reset voice cmc statisticMatch-template Reset voice ipp statistic Reset voice iva statisticRelated command display voice iva statistic Related command display voice ipp statistic Send-busytone enable time seconds Undo send-busytone enable timeSend-busytone Been used to identify nonstandard T38 fax packets Send-ring Shutdown voice entity viewSyntax send-ring Undo send-ring View Voice entity view Shutdown voice subscriber line view Silence-th-spanExample # Change the status of voice entity 4 to Down Undo silence-th-span Slic-gain Subscriber-lineSlic-gain 0 Undo slic-gain Syntax timer dial-interval seconds Undo timer dial-interval Timer dial-interval2611 Timer hookoff-interval Timer first-dialSyntax timer first-dial seconds Undo timer first-dial Timer ring-back Timer wait-digitRelated command hookoff-mode Syntax timer ring-back seconds Undo timer ring-back Transmit gain Related command receive gain and subscriber-lineSyntax transmit gain value Undo transmit gain Example # Enable the tunnel function for VoIP voice entity Tunnel-onSyntax tunnel-on Undo tunnel-on View VoIP entity view Related command cng-on Vad-onUndo type Syntax vad-on Undo vi-card busy-tone-detect custom index Vi-card busy-tone-detect2617 Vi-card cptone-custom Syntax vi-card reboot slot-number Vi-card reboot2619 Voice-setup Voip called-tunnel enableExample # Reset the voice card of slot Syntax voice-setup Voip called-start Voip timerFast-connect Vqa dscp Cs7, or efDscp values Keyword Dscp value in binary Dscp value in decimal By default, DSP buffered data is not monitored Vqa dsp-monitor buffer-timeView Voice view Parameter Range 180 to Voip Configuration Commands Dial Plan Configuration Commands Caller-permit Dial-prefix Related command match-templateonSyntax dial-prefix string Undo dial-prefix Related command match-templateon page 2599 and send-number Display voice number-substituteExample # Specify 0 as a prefix Syntax display voice number-substitute list-tag Related command number-substitute Dot-matchDot-match end-only left-right right-left Undo dot-match First-rule Max-call in voice dial program viewSyntax first-rule rule-number Undo first-rule Undo max-call set-numberI all Max-call in voice entity view Related command max-call in voice entity viewUndo max-call Related command max-call in voice dial program view Related command match-templateon page 2599 and terminatorExample # Configure the longest-number match policy Number-match Number-priority Related command rule and substitute voice dial program viewNumber-substitute Priority Private-lineUndo priority Syntax private-line string Undo private-line Rule Undo rule rule-tag all Meanings of characters in the string argument 2635 Number type Description Input number typeNumbering plan Description Output numbering plan Input numbering plan2637 Select-rule rule-order Undo select-rule rule-order Select-rule search-stop Meanings of integers2639 Integer Meaning Description Undo select-rule type-first Select-rule type-firstMeanings of values Syntax select-stop Undo select-stop Select-stop2641 Related command dot-matchand match-templateon Send-number Related command number-substituteand rule Substitute subscriber line view/voice entity viewSubstitute called calling list-number Undo substitute called calling Substitute voice dial program view AllNumber-substitute and rule To Pstn are outgoing calls Related command match-templateon page 2599 and timer TerminatorSyntax terminator character Undo terminator Example # Specify the pound sign # as the dial terminator Dial Plan Configuration Commands E1 and T1 Configuration Commands AniAni all ka Undo ani Answer enable Related command cas, timer, reverse, and renewSyntax answer enable Undo answer enable Ani-offset Related command re-answer enable and timer dl re-answer CallmodeCas Callmode segment terminal Clear-forward-ack enable Example # Enter the R2 CAS view of TS group Display voice subscriber line Related command mode2651 Dl-bits CNG/CED Signal Default rx-bits Abcd Default tx-bits Abcd Default values of signals in R2 digital line signaling2653 Dtmf enable Related command seizure-ack enable and answer enableSyntax dtmf enable Undo dtmf enable Related command timer dtmf Final-callednum enable Syntax final-callednum enable Undo final-callednum enableRelated command register-valuedigital-end 2655 Force-metering enable Group-b enableSyntax force-metering enable Undo force-metering enable Syntax group-b enable Undo group-b enable Related command register-valuereq-switch-groupb 2657 Syntax mode zone-name default-standard Undo mode Mode Related command register-valueand force-metering enable Example # Adopt Hongkong default R2 signalingPcm Syntax pcm a-law µ-law Undo pcm Pri-set Example # Adopt µ-law companding for signal quantizationSyntax pri-set timeslot-list range Undo pri-set Re-answer enable Syntax re-answer enable Undo re-answer enableRelated command answer enable and timer dl re-answer 2661 Req-callednum-and-switchgroupa req-callingcategory req Changeover to Group a signal value, in the range 1 toDemand-refused digit-end nullnum req-billingcategory Subscriber-busy subscriber-charge subscriber-idle 2663 Related command group-b enable RenewSyntax renew Abcd Undo renew Seizure-ack enable Related command cas and reverseRelated command cas and renew Reverse Related command timer dl seizure Select-modeView CAS view Timeslots Sendring ringbusy enable Related command cas and trunk-directionRelated command timer ring 2667 Signal-value Related command Subscriber line ExampleSpecial-character Syntax special-character character number Different signal values Undo special-character character number Related command timeslot-setand pri-set Tdm-clockExample # Enter the view of voice subscriber line 1/015 Syntax tdm-clock internal line primary Undo tdm-clock Timer dl Release-guardView R2 CAS view 2671 Timer dtmf Syntax timer dtmf time Undo timer dtmf Timer register-pulse persistence Related command dtmf enableTimer register-pulse persistence time Undo timer register-pulse persistence Timer register-complete group-b Related command timer register-completegroup-bTimer register-complete group-b time Undo timer register-complete group-b Timer ring Timer ring ringback ringbusy timeUndo timer ring ringback ringbusy Timeslot-set Related command subscriber line and cas Trunk-direction Related command cas and select-mode Ts block open query reset timeslots timeslots-listCAS view 2677 Related command cas FAX Over IP Configuration Commands Default entity fax Example # Set the maximum fax rate to 9,600 bps globally Display voice faxSyntax display voice fax statistics 2681 Faxvofrstandardswitch FAXVOFRFRF11SWITCHWaitdpbegdemodulatetimeout Waitdpbegmodulatetimeout Fax baudrate Fax baudrate 2400 4800 9600 14400 disable voiceUndo fax baudrate Syntax fax ecm Fax ecmUndo fax ecm Fax level Fax local-train thresholdSyntax fax level level Undo fax level 2685 Example # Configure the fax local training threshold to Example # Configure NSF for fax signal transmissionFax nsf-on Syntax fax nsf-on Undo fax nsf-on Fax protocol pcm g711alaw g711 μlaw Fax protocolUndo fax protocol VoFR entities only support the PPP training mode Fax train-modeFax train-mode local ppp Undo fax train-mode Reset voice fax statistics Reset voice fax statisticsVoip h323-conf tcs-t38 Voip h323-conf tcs-t38 FAX Over IP Configuration Commands Related command match-templateon page 2599, entity on 177Display voice gateway Syntax area-id string Undo area-id string Syntax gk-client Gk-clientGkid Related command gk-id Gk-2nd-idExample # Enter gatekeeper client view Undo gk-2nd-id Gk-security call enable Related command area-id,gw-id,gk-2nd-id,gw-address,ras-onSyntax gk-security call enable Undo gk-security call enable Gk-id Gk-security register-pwd cipher simple password Gk-security register-pwdGw-address Undo gk-security register-pwd Undo gw-address Gw-idUndo gw-id Related command gw-id,gw-address, and gk-id Ras-onVoip h323-descriptor Syntax ras-on 323 Configuration Commands SIP Configuration Commands 178Display voice sip call-statistics Syntax display voice sip call-statistics TPT Message Display voice sip register-state Outband sipDisplay voice sip register-state Syntax outband sip Undo outband Default port number is ProxyUndo proxy ipv4 SIP client view Register-enable Register-enable off onUndo register-enable Registrar ipv4 Reset voice sip SipSip-comp Syntax sip Sip-comp agent Undo sip-comp callee fromSIP client view SIP request messages Sip-comp server Sip-domainUndo sip-comp server View SIP client view Syntax source-ip ip-address Undo source-ip Source-ip2707 SIP Configuration Commands Wildcard-register enable Syntax wildcard-register enable Undo wildcard-registerExample # Enable fuzzy telephone number registration 2709 SIP Configuration Commands Vofr Configuration Commands 179Address Undo address vofr-dynamic vofr-static Call-mode Related command Trunk-idand address ExampleCid select-mode Related command Vofr Example # Set the CID selection mode to min-poll on DlciDisplay fr vofr-info Interface Dlci view Entity vofr Outband vofrUndo entity entity-number vofr Outband vofr Seq-number Seq-numberUndo seq-number Timestamp Related command call-modeTrunk-id Voice bandwidth VofrView Interface Dlci view 2717 Related command call-mode Vofr frf11-timer Vofr frf11-timer timeUndo vofr frf11-timer Hang up successfully in the FRF.11 trunk mode Vofr Configuration Commands Voice Radius Configuration Commands Aaa-clientAccounting Syntax aaa-client Related command acct-methodand accounting Accounting-didSyntax accounting-did Undo accounting-did View Voice AAA client view Related command accounting and accounting-did # Restore the default accounting methodAcct-method Example # Set the accounting method to start-ack Authentication Authentication-didSyntax authentication Undo authentication Related command gw-access-numberand authorization Authorization Related command authorization-didSyntax authorization Undo authorization 2725 Authorization-did Related command gw-access-numberand authenticationSyntax authorization-did Undo authorization-did Related command authentication-did Callednumber receive-method Related command gw-access-number2727 Related command gw-access-numberand process-config Card-digitCdr Syntax card-digit card-digit Undo card-digit Related command display voice call-history-record # Set the alarm threshold for CDRs to 10%Undo cdr all buffer duration threshold Example # Set the number of CDRs that can be saved to Display voice access-number Display voice access-numberGw-access-number and aaa-client 2731 Display voice call-history-record Example # Display call records by calling number Related command cdr2733 Display voice radius statistic Syntax display voice radius statistic Related command reset voice radius statistic 2735VORDS=AAA AAA=VORDS Gw-access-number CMC=VORDS Password-digit # Add the access number 179 and enter access number view# Delete the access number # Delete all access numbers Process-config # Restore the default dialing process for the access number 2739 Redialtimes Undo redialtimes Reset voice radius statistic Gw-access-numberand process-configSelectlanguage Display voice radius statistic Voice Radius Configuration Commands

3Com MSR 30, MSR 50 manual VC-3

Models: MSR 50 MSR 30

Field

VC-3.