Rule in basic IPv6 ACL view | 3Com MSR 30, MSR 50 specs

2108 CHAPTER 139: IPV6 ACL CONFIGURATION COMMANDS

name acl6-name: Specifies the name of the ACL, which is a case insensitive string of 1 to 32 characters. It must start with an English letter and cannot be the English word of all to avoid confusion.

Description Use the reset acl ipv6 counter command to clear statistics about specified or all basic and advanced IPv6 ACLs.

Example # Clear the statistics about IPv6 ACL 2001.

<Sysname> reset acl ipv6 counter 2001

# Clear the statistics about the IPv6 ACL named flow.

<Sysname> reset acl ipv6 counter name flow

rule (in basic IPv6 ACL view)

Syntax rule [ rule-id ] { deny permit } [ fragment logging source { ipv6-address prefix-length ipv6-address/prefix-length any } time-rangetime-name ] *

undo rule rule-id[ fragment logging source time-range ] *

View Basic IPv6 ACL view

Parameter rule-id: IPv6 ACL rule number in the range 0 to 65534.

deny: Defines a deny statement to drop matched packets.

permit: Defines a permit statement to allow matched packets to pass.

fragment: Indicates that the rule applies only to non-first fragments. The rule applies to both fragments and non-fragments without this keyword.

logging: Specifies to log matched packets. The log provides information about ACL rule number, whether packets are permitted or dropped, upper layer protocol that IP carries, source/destination address, source/destination port number, and number of packets.

source { ipv6-address prefix-length ipv6-address/prefix-length any }: Specifies a source address. The ipv6-address and prefix-length arguments specify a source IPv6 address, and its address prefix length in the range 1 to 128. The any keyword indicates any IPv6 source address.

time-rangetime-name:Specifies the time range in which the rule takes effect. The time-nameargument specifies a time range name with 1 to 32 characters. It is case insensitive and must start with an English letter. To avoid confusion, this name cannot be all.

Description Use the rule command to create an IPv6 ACL rule or modify the rule if it has existed.

Page 2108

Image 2108

3Com MSR 30, MSR 50 manual Rule in basic IPv6 ACL view, # Clear the statistics about the IPv6 ACL named flow

Contents

H3C MSR 20/30/50 Series Routers 3Com Corporation Campus Drive Marlborough, MA USA United States Government Legend Contents General Ethernet Interface Configuration Commands Adsl Interface Configuration CommandsPOS Interface Configuration Commands Fundamental Serial Interface Configuration Commands Fundamental CE1/PRI Interface Configuration Commands Fundamental CT1/PRI Interface Configuration Commands 14 E1-F Interface Configuration Commands Fundamental CT3 Interface Configuration Commands 15 T1-F Interface Configuration CommandsFundamental CE3 Interface Configuration Commands DCC Configuration Commands Isdn BRI Interface Configuration CommandsATM Configuration Commands Basic Dlsw Configuration Commands 340 Frame Relay Configuration Commands Garp Configuration Commands Gvrp Configuration CommandsHdlc Configuration Commands Lapb and X.25 Configuration Commands 455 425 Display x25 hunt-group-info Display x25 map 426451 X25 pvc X25 queue-length 453 X25 receive-threshold 454 Link Aggregation Configuration Commands Link Aggregation Debugging CommandsModem Configuration Commands Port Mirroring Configuration Commands Pppoe Client Configuration Commands PPP Link Efficiency Mechanism Configuration CommandsPppoe Server Configuration Commands PPP Debugging Commands Bridging Configuration CommandsIsdn Configuration Commands Debugging ppp Mstp Configuration Commands Vlan Configuration Commands PORT-BASEDVLAN Configuration CommandsVoice Vlan Configuration Commands Port Isolation Configuration Commands Cpos Interface Configuration Commands ARP Configuration Commands Gratuitous ARP Configuration Commands ARP Source Suppression Configuration CommandsAuthorized ARP Configuration Commands Proxy ARP Configuration Commands Dhcp Relay Agent Configuration Commands Dhcp Client Configuration CommandsDhcp Snooping Configuration Commands Bootp Client Configuration Commands DNS Configuration Commands IP Accounting Configuration CommandsIP Addressing Configuration Commands IP Performance Configuration Commands IP Unicast Policy Routing Configuration Commands UDP Helper Configuration CommandsUrpf Configuration Commands Fast Forwarding Commands NAT-PT Configuration Commands 840 Display tcp ipv6 status 842Display natpt address-group 863 Display natpt aging-time 864 display natpt all 69 IPV6 Unicast Policy Routing Configuration Commands Dual Stack Configuration CommandsTunneling Configuration Commands Terminal Access Configuration Commands IP Routing Table Commands BGP Configuration Commands Ebgp-interface-sensitive 977981 Log-peer-change 983 Peer advertise-communityBGP/BGP-VPN instance view BGP Debugging Commands IS-IS Configuration Commands IS-IS Debugging Commands Ospf Configuration Commands 1155 Snmp-agent trap enable ospf 11171128 1140 1179 RIP Configuration CommandsRouting Policy Common Configuration Commands 79 IPV4 Routing Policy Configuration Commands 80 IPV6 Routing Policy Configuration CommandsStatic Routing Configuration Commands 82 IPV6 BGP Configuration Commands 1246 12231243 83 IPV6 IS-IS Configuration Commands 84 IPV6 OSPFV3 Configuration Commands 85 IPV6 Ripng Configuration Commands 86 IPV6 Static Routing Configuration CommandsMulticast Routing and Forwarding Configuration Commands Delete ipv6 static-routes all 1325 ipv6 route-static Igmp Configuration Commands Msdp Configuration CommandsCache-sa-enable 1365 display msdp brief 1366 PIM Configuration Commands 1376 1429 14211422 1451 MLD Configuration Commands93 IPV6 PIM Configuration Commands Multicast VPN Configuration Commands 1495Display multicast-domain vpn-instance share-group 1505 Mpls Basics Configuration Commands Mpls TE Configuration Commands Mpls rsvp-te reliability 1610 Mpls rsvp-te resvconfirm 1611 Mpls L2VPN Configuration Commands Mpls L3VPN Configuration Commands VAM Server Configuration Commands 1697 VAM Client Configuration Commands Ipsec Profile Configuration CommandsDvpn Tunnel Configuration Commands GRE Configuration Commands Traffic Policing TP Configuration Commands Traffic Shaping Configuration CommandsLine Rate Configuration Commands Defining Class Commands Fifo Queuing Configuration Commands PQ Configuration CommandsCQ Configuration Commands WFQ Configuration Commands QOS Token Configuration Commands Priority Mapping Table Configuration CommandsPort Priority Configuration Commands Port Priority Trust Mode Configuration Commands FR QOS Configuration Commands 126 802.1X Configuration CommandsAAA Configuration Commands access-limit Reset dar session 1958 Radius Configuration Commands1927 Hwtacacs Configuration Commands Packet Filter Firewall Configuration Commands NAT Configuration Commands Aspf Configuration Commands aging-timeMAC Authentication Configuration Commands PKI Configuration Commands Portal Configuration Commands RSH Configuration Commands rshCommon Configuration Commands 138 IPV4 ACL Configuration Commands Ipsec Configuration Commands IKE Configuration Commands 142 SSH2.0 Configuration Commands Sftp Configuration Commands bye SSL Configuration Commands Backup Center Configuration Commands 146 IPV4-BASEDVRRP Configuration CommandsVrrp Configuration Commands for IPV6 Device Management Commands NQA Client Configuration Commands Temperature-alarm enable 2263 Temperature-limit2262 2276 NQA Server Configuration Commands Netstream Configuration CommandsNTP Configuration Commands Rmon Configuration Commands Snmp Configuration Commands File System Configuration Commands cd Configuration File Management Commands FTP Server Configuration CommandsFTP Client Configuration Commands ascii Tftp Client Configuration Commands System Maintaining Commands System Debugging CommandsBasic Configuration Commands Information Center Configuration Commands User Interface Configuration Commands 2460 OAP Module Configuration Commands MAC Address Table Management Configuration CommandsPOE Configuration Commands Acfp Configuration Commands Acsei Server Configuration CommandsAcsei Client Configuration Commands Track Configuration Commands Voip Configuration Commands address 2551 Reset ipx routing-table statistics protocol2546 Area 2554 area-id 2592 Dial Plan Configuration Commands 175 E1 and T1 Configuration Commands aniCaller-permit 2639 SIP Configuration Commands FAX Over IP Configuration Commands177 H.323 Configuration Commands Vofr Configuration Commands Voice Radius Configuration Commands aaa-client2716 2734 About this Guide Lists icon conventions that are used throughout this guideLists text conventions that are used throughout this guide Text Conventions Related Documentation Alphabetical Listing of Commands Area Ospf view 1108 area OSPFv3 viewPage Page Rp IPv6 PIM view 1464 c-rp PIM view Page Display bgp vpnv4 vpn-instancerouting-table Page Display ipv6 policy-based-route statistics Page Page Page Page Page Fr compression frf9 385 fr compression iphc Page Igmp last-member-query-interval Ipv6 nd autoconfig managed-address-flag Page Page Page Mpls te resv-style 1631 mpls te retry 2308 Peer allow-as-loopBGP/BGP-VPN instance view Peer ebgp-max-hopBGP/BGP-VPN instance viewPeer keep-all-routesBGP/BGP-VPN instance view Peer next-hop-localBGP/BGP-VPN instance view Peer preferred-valueBGP/BGP-VPN instance viewPeer next-hop-invariableBGP-VPNv4 subaddress family view Peer public-as-onlyBGP/BGP-VPN instance view Pppoe-servermax-sessionsremote-mac Primary accounting Hwtacacs scheme view Qos wred ip-precedence 1850 qos wred queue table Reset aspf session 2007 reset atm interface 112 reset bgp Reset pim ipv6 control-message counters Page Page Ssl client-policy 2215 ssl server-policy Statistics interval 1562 step for IPv4 2100 step for IPv6Page Page Page X29 timer inviteclear-time Page Syntax display interface atm interface-number Public ATM and DSL Interface CommandsDisplay interface atm Interface atm Reset atm interfaceSyntax reset atm interface atm interface-number Clock Configuration CommandsCable Code Code ami hdb3Code ami b8zs Undo code Differential-delay Display interface ima-groupSyntax display interface ima-group group-interfacenumber 115 Frame-format View ATM E1/T1 interface view ParameterATM direct mapping CRC4 ADM ESF ADM Frame-length Ima ima-groupSyntax frame-length 32 64 128 Undo frame-length Syntax ima ima-group group-number Undo ima ima-group Syntax ima-clock ctc link-number number itc Undo ima-clock Ima-clockExample # Add the link of ATM E1 interface 5/0 to IMA group Ima-standard Ima-testIma-test link-number number pattern-id id Undo ima-test By default, IMA group interface test is disabled Interface ima-groupLoopback Syntax loopback cell local payload remote Undo loopback Min-active-links ScrambleSyntax min-active-links number Undo min-active-links Syntax scramble Undo scramble Parameter None View ATM E3/T3 interface view Slave Sets the clock mode as slaveSyntax cable long short Undo cable Frame-format g751-adm g751-plcp g832-adm Frame-format cbit-adm cbit-plcp m23-adm m23-plcp Loopback cell local payload remote ATM E3/T3 Interface Configuration Commands Frame-format sdh sonet Loopback cell local remote View ATM OC-3c interface view, STM-1 interface view 129 ATM OC-3C/STM-1 Interface Configuration Commands Shdsl Interface Configuration Commands ActivateSyntax activate Undo activate View ATM G.SHDSL interface view Display dsl configuration Field Description 133 Display dsl statusSyntax display dsl status interface atm interface-number Gspn Description on the fields of the display dsl status command 135 ITU G991.2 Annex A, ITU Display dsl versionSyntax display dsl version interface atm interface-number Shdsl mode Shdsl annex Example # Set the operating mode of interface ATM 5/0 to CO Shdsl psdShdsl rate Syntax shdsl psd asymmetry symmetry Undo shdsl psd Single-pair interface rate to auto mode Kbps four-wire G.SHDSL interface rate is 4,624 kbps# Configure ATM 5/0 to operate in the auto-negotiation mode Use the undo shdsl snr-margincommand to restore the default Undo shdsl wire Shdsl wireShdsl wire 2 4-auto-enhanced 4-enhanced 4-standard 141 Shdsl Interface Configuration Commands Example # Activate Adsl interface 2/0 Adsl Interface Configuration CommandsView ATM Adsl interface view Adsl standard Adsl tx-attenuationAdsl standard auto g9923 g9925 gdmt glite t1413 Undo adsl standard Bootrom update file 145 Display dsl configuration 147 LS0US FieldDescription Dslam 149 Bdcm Adsl Interface Configuration Commands Syntax crc 16 Undo crc POS Interface Configuration CommandsCrc Display interface pos Syntax display interface pos interface-number 153 LCP opened, Ipcp opened, IP6CP opened Display ip interface pos Display ipv6 interface posDisplay ip interface pos interface-number Syntax display ipv6 interface pos interface-number Flag # Set the framing format on interface POS 1/0 to SDH Related command display interface posExample # Set the SDH overhead byte J0 of POS1/0 interface Link-protocol Loopback local remoteLocal Internal loopback Remote External loopback Mtu That the state of the link layer protocol is reported upInterfaces cannot be connected successfully Syntax mtu size Example # Enable payload scrambling on interface POS 1/0 ThresholdSyntax threshold sd sf value Undo threshold sd sf 159 Example # Set the SD threshold to 10e-4 for POS 1/0 General Ethernet Interface Configuration Commands Combo enableRelated command display port combo and shutdown Description Character Meaning Display brief interfaceSpecial characters used in regular expressions 163 Related command interfaceExample # Display brief information of interfaces Display interface Acronyms for different types of InterfacePvid Interface name Acronyms 165 Field Output queue Fifo queuing 167 Related command speed DuplexFlow-control Syntax duplex auto full half Undo duplex Interface Can be represented as 1/0E1/0 Syntax loopback external internal Undo loopback Support for these two commands varies with device models Port link-modePort link-mode bridge route Undo port link-mode Reset counters interface Example # Configure Ethernet1/0 to work in bridge modeView User view 171 Shutdown Speed Related command duplex 173 General Ethernet Interface Configuration Commands Broadcast-suppression Display loopback-detection Display portSyntax display loopback-detection Display port hybrid trunk Examples Display port-group manualDisplay port-group manual all name port-group-name Flow-interval Group-memberSyntax flow-interval interval Undo flow-interval Undo group-member interface-list Loopback-detection control enable 179 Loopback-detection enable Related command loopback-detection control enableLoopback-detection interval-time View System view/Ethernet interface view 181 Loopback-detection per-vlan enableRelated command display loopback-detection Optical port of a Combo port does not support this command MdiMulticast-suppression Mdi across auto normal Undo port-group manual port-group-name Port-groupPort-group manual port-group-name aggregation agg-id Currently, these two commands are not supported Unicast-suppressionVirtual-cable-test Syntax virtual-cable-test 185 Page Syntax timer hold seconds Undo timer hold Timer holdExample # Configure MTU for Ethernet1/0 to be 1,000 bytes Configuration Commands for Ethernet Interfaces in Route Mode Fundamental Serial Interface Configuration Commands Async modeSyntax async mode flow protocol Undo async mode Baudrate Clock serial interface view Undo baudrateClock dteclk1 dteclk2 dteclk3 dteclk4 dteclkauto View Serial interface view Clock selection option Description Dteclk1191 Code nrzi Country-codeSyntax code nrzi Undo code View Synchronous serial interface view Example # Configure to adopt 32-bit CRC DetectSyntax crc 16 32 none Undo crc Asynchronous serial interface detect dsr-dtr View Asynchronous serial interface view Eliminate-pulseSyntax eliminate-pulse Undo eliminate-pulse Idle-mark Invert receive-clockSyntax idle-mark Undo idle-mark Syntax invert receive-clock Undo invert receive-clock Invert transmit-clock Syntax invert transmit-clock Undo invert transmit-clock 197 Mtu on serial interfacesSyntax loopback Undo loopback Physical-mode Phy-mruSyntax physical-mode async sync Syntax phy-mru size Undo phy-mru 199 Reverse-rtsSyntax reverse-rts Undo reverse-rts Virtualbaudrate Virtualbaudrate virtualbaudrateUndo virtualbaudrate Baudrate Fundamental CE1/PRI Interface Configuration Commands Channel-set CE1/PRI interface view Clock CE1/PRI interface view Clock Controller e1 number Code CEI/PRI interface viewController e1 Syntax detect-ais Undo detect-ais Detect-aisCrc 16 32 none Description on the fields of the command Display controller e1Syntax display controller e1 interface-number 205 Error-diffusion restraint config Undo error-diffusion restraint config Error-diffusion restraint enable Error-diffusion restraint restart-channelBy default, error packets diffusion restraint is enabled Example # Enable error packets diffusion restraint Two types of line idle code are available 0x7E and 0xFF Frame-format CE1/PRI interface viewIdlecode CE1/PRI interface view Undo itf type number Itf CE1/PRI interface viewItf number number type 7e ff Loopback CE1/PRI interface view Pri-set CE1/PRI interface viewLoopback local payload remote Pri-set timeslot-list list Reset counters controller e1 Reset counters controller e1 interface-numberCommand Display controller e1 interface-number command Undo using Using CE1/PRI interface viewUsing ce1 e1 Fundamental CT1/PRI Interface Configuration Commands Alarm-thresholdLevel-2 Level-2 , level-3 , and level-4 Bert CT1/PRI interface view Bert pattern 215 220 time minutes unframedUndo bert Ranges from 1 to 1,440 655ft Cable CT1/PRI interface viewChannel-set CT1/PRI interface view Clock CT1/PRI interface view View CT1/PRI interface view Code CT1/PRI interface view Controller t1Ami Adopts AMI line code format # Set the line code format of the interface T1 2/0 to AMI Undo data-coding Data-coding CT1/PRI interface viewData-coding inverted normal 219 Display controller t1Syntax display controller t1 interface-number Clock or slave for the line clock 221 Error-diffusion restraint config 223 By default, the function is disabledExample # Enable error packet diffusion restraint Support of this command varies with device model Error packet diffusion restraint functionFdl Set-number argument is a channel set number Frame-format esf sf Frame-format CT1/PRI interface viewIdlecode CT1/PRI interface view Itf CT1/PRI interface view Loopback CT1/PRI interface viewSyntax itf number number type 7e ff Undo itf number type Syntax loopback local payload remote Remote Enables the interface to perform remote loopback # Enabled remote loopback on interface T1 2/0Pri-set CT1/PRI interface view Loopback on the CT1/PRI interface Reset counters controller t1 Reset counters controller t1 interface-numberFor a CT1/PRI interface # Clear the controller counter for CT1/PRI interface T1 2/0 Sendloopcode 229 Fundamental CT1/PRI Interface Configuration Commands Display fe1 serial interface-number E1-F Interface Configuration CommandsDisplay fe1 Fe1 cable Fe1 clockFe1 cable long short Undo fe1 cable Fe1 code Fe1 detect-ais Fe1 frame-format Fe1 loopback Local Sets the interface in internal loopback mode Fe1 timeslot-listUndo fe1 loopback Syntax fe1 timeslot-list list Undo fe1 timeslot-list Related command fe1 unframed Fe1 idlecodeFe1 itf Syntax fe1 idlecode 7e ff Undo fe1 idlecode Undo fe1 unframed Fe1 unframedFe1 unframed Related command fe1 timeslot-list Display ft1 serial interface-number T1-F Interface Configuration CommandsDisplay ft1 Description on the fields of the display ft1 serial command 241 Bert statestopped, not completed Ft1 bert T1-F interface view Ft1 bert pattern 215 220 time minutes unframedUndo ft1 bert T1-F interface view Ft1 cable Syntax ft1 cable long decibel short length Undo ft1 cableView T1-F interface view 243 Ft1 clock Ft1 codeFt1 clock master slave Undo ft1 clock Undo ft1 data-coding Ft1 data-codingFt1 data-coding inverted normal Ft1 fdl Ft1 frame-format Ft1 idlecode Ft1 itfFt1 idlecode 7e ff Undo ft1 idlecode Use the undo ft1 loopback command to restore the default Ft1 loopbackFt1 loopback local payload remote Undo ft1 loopback 249 # Set T1-F interface Serial 2/0 in local loopback modeFt1 timeslot-list On the T1-F interface Ft1 alarm-thresholdUndo ft1 alarm-threshold Ft1 sendloopcode 251 T1-F Interface Configuration Commands Bert pattern 27 211 215 qrss time number unframed Fundamental CE3 Interface Configuration CommandsBert CE3 Interface Clock CE3 interface view Controller e3Display controller e3 Example # Enter the view of interface E3 2/0 255 Display controller e3Syntax display controller e3 interface-number Fundamental CE3 Interface Configuration Commands E1 bert 257 Related command e1 unframed E1 channel-setE1 set clock Syntax e1 line-numberset clock master slave E1 set frame-format Undo e1 line-numberset clockView CE3 interface view 259 Undo e1 line-numbershutdown E1 set loopbackE1 shutdown Related command e1 channel-set E1 unframedFe3 Undo e1 line-numberunframed CE3 interface in FE3 mode view Set the DSU mode or the subrateUse the undo fe3 command to restore the default These two commands are only available in E3 mode Loopback CE3 interface view National-bitNational-bit 0 Undo national-bit Using CE3 interface view Related command controller e3Syntax using ce3 e3 Undo using Example # Set the national bit to 0 on interface E3 2/0 Fundamental CT3 Interface Configuration Commands Alarm CT3 interface viewAlarm detect generate ais febe idle rai Undo alarm detect generate ais febe idle rai # Enable CT3 interface T3 2/0 to send AIS alarm signals Bert CT3 interface view Cable CT3 interface view Clock CT3 interface viewSyntax cable feet 267 Related command display controller t3 Controller t3Example # Enter the view of interface T3 2/0 None Adopts no CRC 269 Display controller t3Syntax display controller t3 interface-number AIS Configurable and default to line 271 LOS, LOF, AIS, or RAI Feac CT3 interface view Frame-format c-bit m23 Frame-format CT3 interface viewFt3 275 Loopback CT3 interface view Mdl CT3 interface view 277 # Send path messages on CT3 interface T3 2/0 T1 alarm# Set LIC to hello for CT3 interface T3 2/0 T1 bert 279 Related command t1 unframed T1 channel-set T1 sendloopcode 281 T1 set clock T1 set frame-format T1 set loopback T1 set fdlView CT3 interface view 283 T1 show 285 Description on the fields of the t1 show commandT1 shutdown Related command t1 channel-set T1 unframedUndo t1 line-numbershutdown Syntax t1 line-numberunframed undo t1 line-numberunframed Using CT3 interface view Using ct3 t3Ct3 Sets the CT3 interface to operate in channelized mode T3 Sets the CT3 interface to operate in unchannelized mode Fundamental CT3 Interface Configuration Commands Isdn BRI Interface Configuration Commands Loopback Isdn BRI interface viewLoopback b1 b2 both Fixed Isdn interfaces on your router, if there is any Isdn BRI Interface Configuration Commands ATM Configuration Commands Related command atm-classAtm class Atm-class Related command atm class Atm-link checkSyntax atm-link check Undo atm-link check View ATM P2P sub-interface view Display atm class atm-class-name Related command Display atm interface ExampleDisplay atm class Display atm interface Syntax display atm interface atm interface-number Display atm map-info 295 Display atm pvc-group VPI/VCIPVC-NAME State Display atm pvc-info 297 Index EncapsulationSyntax encapsulation aal5-encap Undo encapsulation 299 Ip-precedenceExample # Enter Atm1/0 interface View PVC view/ATM Class view Related command pvc-group,pvcMap bridge # Configure an IP address 10.1.1.1/16 for the VE interface Map ip# Create PVC 1/102 on the ATM interface Atm2/0 Map ip inarp minutes broadcast Undo map ip inarp Map ppp Syntax map ppp virtual-template vt-number Undo map ppp 303 # Create a PPPoA map using the VT interface created# Create PVC 1/101 on interface Atm1/0 Oam ais-rdi 305 Oam frequencyUndo oam frequency Oamping interface Pvc Related command display atm pvc-info,pvc max-number VCI range for each type of ATM interface307 Interface type Related command ip-precedence,pvc Pvc-groupPvc max-number Syntax pvc max-number max-number Undo pvc max-number Pvp limit Undo pvp limit vpi Interface type Value range of output-pcr Service cbrExample # Set the traffic of VP with vpi 1 to 2M Service ubr Service vbr-nrtRelated command service vbr-nrt,service vbr-rt,service ubr Syntax service ubr output-pcr Service vbr-rt Related command service ubr, service vbr-rt, and service cbr 313 Parameters None# Bring up ATM 5/0 Transmit-priority Syntax transmit-priority value Undo transmit-priority DCC Configuration Commands Related command dialer bundle-memberDialer bundle Dialer bundle-member Related command dialer bundle Dialer callback-center Dialer call-in 317 Dialer circular-group Related command dialer callback-centerRelated command interface dialer Dialer enable-circular Dialer enable-circularUndo dialer enable-circular Bundle-member command Related command dialer circular-group Related command dialer thresholdDialer flow-interval Dialer isdn-leased physical interface view 321 Dialer numberSyntax dialer number dial-number Undo dialer number Related command dialer route Dialer priorityDialer queue-length Syntax dialer priority priority Undo dialer priority Dialer route 323 Dialer threshold 325 Dialer timer autodialRelated command dialer flow-interval Dialer timer compete Dialer timer enable Dialer timer idleSyntax dialer timer enable seconds Undo dialer timer enable Syntax dialer timer idle seconds Undo dialer timer idle Syntax dialer user username Undo dialer user Dialer timer wait-carrierDialer user Dialer-group Example # Add a remote username routerbSyntax dialer-group group-number Undo dialer-group 329 Related command dialer-rule Example # Add interface Serial 2/0 to dialer access groupDialer-rule Undo dialer-rule group-number Related command dialer-group Display dialerAny view Number Display interface dialer Display interface dialer numberNumber Dialer interface number Information about all the dialer interfaces 333 Interface dialerSyntax interface dialer number Undo interface dialer number Ppp callback Ppp callback ntstringPpp callback client server Undo ppp callback client server 335 Related command ppp callbackUndo ppp callback ntstring DCC Configuration Commands Basic Dlsw Configuration Commands Example # Configure Serial 1/0 to use Nrzi encodingDisplay dlsw circuits Syntax display dlsw circuits circuit-id verbose Display dlsw information Display dlsw information local ip-address Display dlsw remote # Display the local information about capabilities exchangeSyntax display dlsw remote ip-address 339 Display dlsw reachable-cache Display dlsw reachable-cacheInformation of DLSw # Display the reachability information of DLSw Description on the fields of the display llc2 command Display llc2Syntax display llc2 circuit circuit-id 341 Dlsw bridge-set Dlsw enableSyntax dlsw enable Undo dlsw enable 343 # Enable DLSwDlsw ethernet-frame-filter Dlsw local 345 # Allow the router to access SAP addresses 12Dlsw reachable # Permit access to user-configured MAC addresses only Dlsw reachable-cacheDlsw remote Undo dlsw remote ip-address 347 Related command sdlc mac-map remote Dlsw reverseDlsw max-transmission Syntax dlsw reverse mac-address 349 Dlsw multicastUndo dlsw multicast Dlsw timer 351 Link-protocol sdlcSyntax link-protocol sdlc Llc2 max-ack Llc2 max-pduSyntax llc2 max-ack length Undo llc2 max-ack Syntax llc2 max-pdu length Undo llc2 max-pdu Llc2 max-send-queue Llc2 max-transmissionSyntax llc2 max-send-queue length Undo llc2 max-send-queue 353 Llc2 modulo Llc2 receive-windowLlc2 modulo 8 Undo llc2 modulo Llc2 timer ack Llc2 timer ack-delaySyntax llc2 timer ack mseconds Undo llc2 timer ack 355 Llc2 timer busy Llc2 timer detectSyntax llc2 timer busy mseconds Undo llc2 timer busy Syntax llc2 timer detect mseconds Undo llc2 timer detect 357 Llc2 timer pollSyntax llc2 timer poll mseconds Undo llc2 timer poll Reset dlsw reachable-cache Llc2 timer rejectReset dlsw circuits Reset dlsw tcp Syntax reset dlsw tcp ip-addressDescription on the fields of the reset dlsw tcp command 359 Sdlc controller Sdlc enable dlsw Syntax sdlc enable dlsw Undo sdlc enable dlswSdlc mac-map local 361 Sdlc mac-map remote Sdlc max-pdu Sdlc max-send-queueSyntax sdlc max-pdu number Undo sdlc max-pdu Syntax sdlc max-send-queue length Undo sdlc max-send-queue Sdlc max-transmission Sdlc moduloView Synchronous serial interface view Specifies the modulus value to be 365 Related command sdlc sap-map remoteSdlc sap-map local Related command sdlc sap-map local Sdlc sap-map remoteSdlc simultaneous Syntax sdlc simultaneous Undo sdlc simultaneous Undo sdlc status primary secondary Sdlc statusSdlc status primary secondary Syntax sdlc timer ack mseconds Undo sdlc timer ack Sdlc timer ackSdlc timer lifetime Sdlc timer poll Syntax sdlc timer poll mseconds Undo sdlc timer pollSdlc window Syntax sdlc window length Undo sdlc window Sdlc xid Undo sdlc xid sdlc-address Frame Relay Configuration Commands AnnexgDisplay fr compress Annexg dce dte Display fr dlci-switch Related commands fr compression frf9 Related command fr inarp Example Display fr inarp-infoDisplay fr interface # Display statistics about frame relay Inarp packets Display fr lmi-info Range 0 to# Display information about all frame relay interfaces Frame 375 Related command fr compression iphcDisplay fr iphc Display fr map-info Mappings or the one for the specified interfaceWhether dynamic address mapping operates normally Fr map ip , fr inarp Dlci = 100, IP Inarp Display fr map-info pppofr377 Display fr pvc-info 1007Statistics about data transmitted and received on them Fr dlci Display fr statistics 379 Display interface mfr MTU Display mfr 381 Description on the fields of the display mfr command LID 383 Display x25 templateSyntax display x25 template name Related command x25 template, x25-template Fr compression frf9 Fr compression iphcSyntax fr compression frf9 Undo fr compression View Subinterface point-to-point view Undo fr dlci dlci-number Fr dlciUndo fr compression iphc Fr dlci-switch Use the undo fr dlci command to cancel the configurationUndo fr dlci-switch in-dlci Related command fr switching Fr inarp Syntax fr inarp ip dlci-number Undo fr inarp ip dlci-number 389 Fr interface-typeSyntax fr interface-type dce dte nni Undo fr interface-type Fr iphc Fr lmi n391dteTcp-include Fr map ip , fr compression iphc 391 Fr lmi n392dceSyntax fr lmi n392dce n392-value Undo fr lmi n392dce Fr lmi n392dte Syntax fr lmi n392dte n392-value Undo fr lmi n392dte Fr lmi n393dce Fr lmi n393dteSyntax fr lmi n393dce n393-value Undo fr lmi n393dce Syntax fr lmi n393dte n393-value Undo fr lmi n393dte Fr lmi t392dce Syntax fr lmi t392dce t392-value Undo fr lmi t392dce Undo fr lmi type Fr lmi typeFr lmi type ansi nonstandard q933a bi-direction Fr map ip Fr switch Related command interface virtual-templateonUndo fr switch name Fr map ppp Fr switching Syntax fr switching Undo fr switching 399 Interface mfrInterface serial Link-protocol fr Link-protocol fr ietf nonstandard Link-protocol fr mfr Mfr bundle-nameSyntax link-protocol fr mfr interface-number Syntax mfr bundle-name name Undo mfr bundle-name Mfr fragment Mfr fragment-sizeSyntax mfr fragment Undo mfr fragment Syntax mfr fragment-size bytes Undo mfr fragment-size 403 Mfr link-nameSyntax mfr link-name name Undo mfr link-name name Syntax mfr retry number Undo mfr retry Mfr retryMfr stateup-respond-addlink Mfr timer ack Syntax mfr timer ack seconds Undo mfr timer ackRelated command mfr timer hello, mfr retry 405 Mfr timer hello Syntax mfr timer hello seconds Undo mfr timer helloMfr window-size Syntax mfr window-size number Undo mfr window-size Reset fr inarp View Frame relay switching viewSyntax reset fr inarp Related command fr inarp Example # Clear all the frame relay dynamic address maps Reset fr pvcRelated command fr lmi t392dce X25-template X25 templateSyntax x25-template name Undo x25-template name Syntax x25 template name Undo x25 template name Frame Relay Configuration Commands Garp Configuration Commands Display garp timerSyntax display garp timer interface interface-list Display garp statistics Garp timer Related command garp timer, garp timer leaveallExample # Display Garp timers on port Ethernet 1/0 View Ethernet interface view, port group view Garp timer leaveall Related command display garp timerDependencies of Garp timers Timer Lower limit Upper limit Display gvrp statistics Reset garp statisticsReset garp statistics interface interface-list Syntax display gvrp statistics interface interface-list Gvrp Configuration CommandsDisplay gvrp statistics Related command display gvrp status Display gvrp statusGvrp Syntax gvrp Gvrp registration Gvrp registration fixed forbidden normalUndo gvrp registration Display garp statistics Gvrp Configuration Commands Hdlc Configuration Commands Timer holdTimer hold seconds Link-protocol hdlc Hdlc Configuration Commands X25 hunt-group Lapb and X.25 Configuration CommandsChannel Lapb and X.25 Configuration Commands Lapb DCE Description on the fields of the display interface command423 Display x25 alias-policy Related command x25 alias-policy Example Display x25 cugDisplay x25 hunt-group-info Display x25 cug local-cug local-cug-number network-cug Syntax display x25 map Related command x25 hunt-groupDisplay x25 map Description on the fields of the display x25 map command Display x25 padExample # Display the X.25 address mapping table Syntax display x25 pad pad-id Display x25 switch-table pvc Display x25 switch-table svcSyntax display x25 switch-table pvc Syntax display x25 switch-table svc dynamic static Related command x25 switch svc Example # Display X.25 SVC static switching tableDisplay x25 vc Syntax display x25 vc lci Data 0/0 Interrupt 0/0 SVC Description on the fields of the display x25 vc command431 Display x25 x2t switch-table Display x25 xot Lapb max-frame Syntax lapb max-frame n1-value Undo lapb max-frame433 Difference between N1 Related command lapb window-size Lapb moduloLapb retry Parameter 8 Modulo Lapb timer Undo lapb timer t1 t2 t3Lapb window-size Syntax lapb window-size k-valueundo lapb window-size Link-protocol lapb dce dte ip multi-protocol Link-protocol lapbLapb modulo Pad Link-protocol x25 dce dte ietf nonstandard Reset xot Reset Reset lapb statistics Syntax reset lapb statisticsTranslate ip Undo translate ip ip-addressport port-number Parameter x.121-address X.121 address TranslateUndo translate x25 x.121-address X25 alias-policy 441 X25 call-facility Description on the user facility option X25 cug-service Related command x25 map, x25 modulo443 Option Description Window-size X25 default-protocol Related command x25 local-cug X25 hunt-group 445 X25 ignore called-address X25 ignore calling-address X25 local-cug 447 Undo x25 map ip compressedtcp protocol-address Related command x25 call-facility,x25 cug-serviceX25 map Send-delay delay-time 449Option Description Broadcast Protocols such as Routing Information Protocol X25 modulo Syntax x25 modulo 8 Undo x25 modulo X25 packet-size # Set the modulo on the X.25 interface Serial 2/0 toUndo x25 packet-size 451 Description on PVC attribute option X25 pvcUndo x25 pvc pvc-number 453 X25 queue-lengthSyntax x25 queue-length queue-length Undo x25 queue-length Related command x25 window-size X25 receive-threshold 455 X25 response called-addressX25 response calling-address Related command x25 map X25 reverse-charge-accept X25 switch pvc Related command x25 call-facility,x25 mapUndo x25 switch pvc pvc-number1 X25 roa-list Lapb and X.25 Configuration Commands 459 X25 switch svc121 mode matching rules Characters Input rules Input rules of X.121 address mode matching stringNumber SVC route number X25 switch svc hunt-group 461 X25 switch svc xot Related command display x25 switch-table svc X25 switching Syntax x25 switching Undo x25 switching X25 timer hold X25 timer idleExample # Enable X.25 switching function Syntax x25 timer hold minutes Undo x25 timer hold X25 timer tx0 Syntax x25 timer tx0 seconds Undo x25 timer tx0Related command x25 timer tx1, x25 timer tx2, x25 timer tx3 465 X25 timer tx1 X25 timer tx2Syntax x25 timer tx1 seconds Undo x25 timer tx1 Related command x25 timer tx0, x25 timer tx2, x25 timer tx3 X25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx3Syntax x25 timer tx3 seconds Undo x25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx2 Syntax x25 vc-per-map count Undo x25 vc-per-map X25 vc-per-mapX25 vc-range 469 X25 window-sizeUndo x25 window-size Syntax x25 x121-address x.121-address Undo x25 x121-address X25 x121-addressX25 xot pvc Related command display x25 vc, x25 switching Undo x25 pvc pvc-number1XOT channel parameter option 471 X29 timer inviteclear-time Link Aggregation Configuration Commands Display lacp system-idDisplay link-aggregation interface Syntax display lacp system-id Link Aggregation Configuration Commands 475 Display link-aggregation summarySyntax display link-aggregation summary Display link-aggregation verbose Example # Display the link aggregation group summarySyntax display link-aggregation verbose agg-id AL ID 477 Lacp port-priority Lacp system-priority Link-aggregation group descriptionExample # Assign Lacp priority 64 to a port 479 Link-aggregation group mode Related command display link-aggregation verboseRelated command display link-aggregation summary Port link-aggregation group Reset lacp statistics Related command Display link-aggregation verbose ExamplePort-group aggregation Port-group aggregation agg-id Related command display link-aggregation interface Example # Clear statistics about Lacp on all ports Debugging lacp packet Link Aggregation Debugging CommandsView User view Default Level 1 Monitor level Link Aggregation Debugging Commands 485 Device sent an Lacp protocol packet through Ethernet 1/1Length of the Terminator field in the protocol packet is Device received an Lacp protocol packet through Ethernet 1/1 Debugging lacp state 487 Debugging link-aggregation error Syntax debugging link-aggregation error Error Debugging link-aggregation eventSyntax debugging link-aggregation event 489 Aggregation group 10 existed. It contained Ethernet 1/1 # Remove aggregation groupAggregation group 10 was removed Operation key of port Ethernet 1/1 Key 1 was removed Modem auto-answer Modem Configuration CommandsModem Modem timer answer Syntax modem timer answer time Undo modem timer answer With caution under the guidance of technicians Sendat command can issue only one AT command at a timeSendat Specifies the communication standard to be adopted Service modem-callback Example # Send dialing command to call numberSyntax service modem-callback 495 Undo service modem-callback Example # Enable the callback function Port Mirroring Configuration Commands Display mirroring-groupMirroring-group Syntax display mirroring-group groupid local Mirroring-group mirroring-port Undo mirroring-group groupid local Mirroring-group monitor-port 499 Mirroring-port # Add POS 5/1 to local port mirroring group 501 Monitor-port# Add Cpos 6/1 to local port mirroring group Port Mirroring Configuration Commands Syntax display interface mp-group mp-number PPP and MP Configuration 31 CommandsDisplay interface mp-group Related command interface virtual-template Display interface virtual-templateSyntax display interface virtual-template number Example # View the information about VT Description on the fields of the display ppp mp command Display ppp mpLink-protocol ppp , ppp mp 505 Display virtual-access For description on the output fields, refer to Table Interface mp-group 507 Interface virtual-template Ip address ppp-negotiate Ppp account-statistics enable Ppp account-statistics enableUndo ppp account-statistics enable Link-protocol ppp Ppp authentication-mode Ppp authentication-mode chap pap call-in domain isp-nameUndo ppp authentication-mode Chap, pap Authentication modes. Use either mode Ppp chap password Related command ppp authentication-modechapPpp chap user Syntax ppp chap user username Undo ppp chap user Related command ppp authentication-modePpp ipcp dns Ppp ipcp dns admit-any Ppp ipcp dns requestSyntax ppp ipcp dns admit-any Undo ppp ipcp dns admit-any Syntax ppp ipcp dns request Undo ppp ipcp dns request Related command remote address Ppp ipcp remote-address forced 515 Ppp lqcUndo ppp lqc Ppp mp Ppp mp binding-modeSyntax ppp mp Undo ppp mp Related command Ppp mp user Example Ppp mp max-bindPpp mp max-bind max-bind-num Undo ppp mp max-bind Related command Ppp mp Example Ppp mp min-bindPpp mp min-bind min-bind-num Undo ppp mp min-bind Related command dialer threshold on Ppp mp min-fragmentPpp mp min-fragment size Undo ppp mp min-fragment Ppp mp mp-group Ppp mp userSyntax ppp mp mp-group number Undo ppp mp Example # Add interface Serial 3/0 to MP-group Related command ppp mp and ppp mp max-bind Ppp mp virtual-templateSyntax ppp mp virtual-template number Undo ppp mp 521 Ppp timer negotiate Related command local-useron page 1940, password onSyntax ppp timer negotiate seconds Undo ppp timer negotiate Ppp pap local-user 523 Remote addressUndo remote address Timer hold Display ppp compression iphc tcp PPP Link Efficiency Mechanism Configuration CommandsDisplay ppp compression iphc rtp Syntax ip tcp vjcompress Undo ip tcp vjcompress Display ppp compression stac-lzsIp tcp vjcompress Ppp compression iphc 527 Ppp compression iphc rtp-connections 529 Ppp compression iphc tcp-connectionsPpp compression stac-lzs Ppp mp lfi Syntax ppp mp lfi Undo ppp mp lfi 531 Ppp mp lfi delay-per-fragReset ppp compression iphc PPP Link Efficiency Mechanism Configuration Commands Display pppoe-server session all packet Pppoe Server Configuration CommandsDisplay pppoe-server session Pppoe-server bind Pppoe-server log-information off 535 Pppoe-server max-sessions local-macPppoe-server max-sessions remote-mac Reset pppoe-server Pppoe-server max-sessions totalPppoe-server max-sessions total number Undo pppoe-server max-sessions total 537 Pppoe Server Configuration Commands Pppoe Client Configuration Commands Display pppoe-client session Pppoe-client dial-bundle-number Reset pppoe-client Related command Reset pppoe-clientReset pppoe-client all dial-bundle-number number Related command pppoe-client Sysname reset pppoe-client all PPP Debugging Commands Debugging ppp Description on the fields of the debugging ppp event command Description on the fields of the debugging ppp ipcp command 545 LCP moved from the starting state to the reqsent state Description on the fields of the debugging ppp ipcp commandLCP moved from the initial state to the starting state 547 PPP Debugging Commands Bridging Configuration Commands Bridge bridge-set enableSyntax bridge bridge-setenable Undo bridge bridge-setenable Bridge aging-time Bridge enable Example # Enable bridge set# Enable IP bridging on bridge set Syntax bridge enable Undo bridge enable Example # Enable bridging Bridge learningBridge mac-address 551 Bridge routing Bridge routing-enable Syntax bridge routing-enable Undo bridge routing-enableBridge-set Syntax bridge-set bridge-set Undo bridge-set bridge-set Display bridge address-table Display bridge information Syntax display bridge information bridge-set bridge-set555 Dynamic S--STATIC Display bridge traffic 557 Display interface bridge-templateSyntax display interface bridge-template interface-number UP/DOWN Fr map bridgeSyntax fr map bridge dlci broadcast Undo fr map bridge dlci Related command display fr map-infoon Bridge routing-enableInterface bridge-template Parameters Related command interface bridge-template Mac-address bridge-template interface viewMap bridge-group Syntax mac-address mac-address Undo mac-address 561 Reset bridge address-tableReset bridge traffic X25 map bridge X25 map bridge x121-address x.121-address broadcastUndo x25 map bridge x121-address x.121-address Display x25 map on Isdn Configuration Commands Dialer isdn-leased Isdn BRI interface viewDialer isdn-leased 128k number Undo dialer isdn-leased 128k number Display isdn active-channel Display isdn call-info Example # Display the current state of Isdn interface 2/0 565 Display isdn call-record Display isdn parameters 567 Display isdn spid IsdnKbri Kpri Isdn bch-local-manage 569 Bch-local-manage command on the user side Channels in ascending order by defaultIsdn bch-select-way Isdn caller-number Isdn calling Isdn check-called-numberUndo isdn calling Undo isdn check-called-number check-index Isdn check-time Syntax isdn check-time date-time Undo isdn check-time Isdn crlength Isdn ignore connect-ackUndo isdn crlength Syntax isdn ignore connect-ack Settings must be the same as those on the exchange Isdn ignore hlcUndo isdn ignore connect-ack Isdn ignore hlc Isdn ignore llc Voice calls placed on the BRI interface 1/0Isdn ignore llc Undo isdn ignore llc Configured Isdn ignore sending-completeIsdn ignore sending-complete incoming outgoing Undo isdn ignore sending-complete incoming outgoing Isdn L3-timer Undo isdn L3-timer all timer-nameDescription of Q931 timers Value range Default Timer-name Seconds Isdn link-mode Isdn number-propertySyntax isdn link-mode p2p Undo isdn link-mode View Isdn BRI interface Protocol Field Bit value Definition Type Code scheme Types and code schemes of Isdn numbers579 NTT Qsig Set the type and code scheme of Isdn numbers 581 Isdn overlap-sending Calls Isdn pri-slipwnd-size 583 Syntax isdn protocol-type protocol Undo isdn protocol-type Isdn protocol-modeIsdn protocol-type Isdn q921-permanent Example # Apply Isdn Etsi on interface BRI 1/0Syntax isdn q921-permanent Undo isdn q921-permanent View Isdn BRI interface view Isdn send-restart Isdn spid autotriggerSyntax isdn send-restart Undo isdn send-restart Syntax isdn spid autotrigger Isdn spid timer Syntax isdn spid timer seconds Undo isdn spid timerIsdn spid nit Syntax isdn spid nit Undo isdn spid nit Undo isdn spid service Isdn spid serviceIsdn spid service audio data speech Isdn spid resend Isdn spid1Syntax isdn spid resend times Undo isdn spid resend Syntax isdn spid1 spid LDN Syntax isdn spid2 spid LDN Undo isdn spid2 Isdn spid2Undo isdn spid1 Configuration of the Isdn calling command This command applies only on NI-compliant BRI interfacesSpid String of 1 to 20 digits LDN Local dialing number, a string of 1 to 30 digits Isdn two-tei Syntax isdn two-tei Permanent-active Undo isdn two-teiView BRI interface view Syntax permanent-active Undo permanent-active Power-source Syntax power-source Undo power-source # Bring up BRI 2/0 595 Isdn Configuration Commands Mstp Configuration Commands Active region-configurationCheck region-configuration Syntax active region-configuration Display stp Port numberBrief Displays brief information Information Related commands reset stp 599 Display stp abnormal-port Display stp abnormal-portAbnormally blocked ports Root guard action Display stp down-port Display stp historySyntax display stp down-port Syntax display stp instance instance-id history Display stp region-configuration Syntax display stp region-configuration Related commands stp region-configuration Description on the fields of the display stp root commandDisplay stp root Syntax display stp root Display stp tc ModelSent Tree instance, in port name order Instance Region-nameExamples # Map Vlan 2 to MST instance Syntax region-name name Undo region-name Display stp Reset stpReset stp interface interface-list Syntax stp enable disable Undo stp Revision-levelStp Syntax revision-level level Undo revision-level Related commands stp mode Examples # Enable the Mstp feature globally# Disable Mstp on port Ethernet 1/1 Stp bpdu-protection Stp bridge-diameter Stp compliance Stp config-digest-snooping Stp cost Stp edged-port enable disable Or undo stp edged-port enable command to non-edge portStp edged-port Undo stp edged-port Examples # Configure port Ethernet 1/1 as a non-edge port Stp loop-protectionStp max-hops Syntax stp loop-protection Undo stp loop-protection Stp mcheck Syntax stp mcheck Stp mcheck , stp Stp modeStp no-agreement-check Examples # Enable No Agreement Check on Ethernet 1/1 Stp pathcost-standardView System view Parameters 802.1D-1998 Stp point-to-point 617 Stp port-log Stp port priority 619 Undo stp instance instance-id priority Stp priorityStp instance instance-id priority priority Stp region-configuration Stp root primary Stp root secondary Stp instance instance-id root secondary Syntax stp tc-protection enable Stp tc-protection disable Stp root-protectionStp tc-protection Syntax stp root-protection Undo stp root-protection Stp timer forward-delay Stp tc-protection threshold 625 Stp timer helloSyntax stp timer hello centi-seconds Undo stp timer hello Stp timer max-age 627 Stp timer-factorSyntax stp timer-factor number Undo stp timer-factor Syntax vlan-mapping modulo modulo Stp transmit-limitVlan-mapping modulo Examples # Map VLANs to MSTIs as per the modulo value 629 Mstp Configuration Commands Syntax display interface vlan-interface vlan-interface-id Vlan Configuration CommandsDisplay interface vlan-interface # Display the information of VLAN-interface Vlan-interface-id Vlan interface IDVlan interfaces will be displayed Related command vlan Display vlanExample # Display Vlan 2 information # Display Vlan 3 information Related command display interface vlan-interface Description on the fields of the display vlan commandInterface vlan-interface Example # Create Vlan interface 635 Related command display ip interface onIp address Vlan View Vlan interface view Related command display vlan Example # Enter Vlan 2 view# Create Vlan 4 through Vlan 637 Vlan Configuration Commands PORT-BASED Vlan Configuration Commands Port access vlanSyntax port access vlan vlan-id Undo port access vlan Port Syntax port hybrid pvid vlan vlan-id Undo port hybrid pvid Related command port link-typePort hybrid pvid vlan Port hybrid vlan 641 Port link-type Port trunk permit vlan 643 Port trunk pvid vlanSyntax port trunk pvid vlan vlan-id Undo port trunk pvid Related command port link-type Voice Vlan Configuration Commands Voice vlan enable Example Syntax voice vlan vlan-idenableDisplay voice vlan state Voice vlan Undo voice vlan enable Related command display voice vlan stateVoice vlan aging Syntax voice vlan aging minutes Undo voice vlan aging Voice vlan mac-address Voice vlan enableSyntax voice vlan enable Undo voice vlan enable Ffff-f000-0000 Range of 1 to 30 charactersBe a broadcast, multicast or address of all 0s or all fs Display voice vlan oui Example Syntax voice vlan mode auto Undo voice vlan mode auto Voice vlan mode autoVoice vlan security enable Example # Disable the security mode of the voice Vlan 651 Voice Vlan Configuration Commands Port Isolation Configuration Commands Port-isolate enableSyntax port-isolate enable Undo port-isolate enable Display port-isolate group Port Isolation Configuration Commands Standby routing-rule Dynamic Route Backup Configuration CommandsStandby routing-group Standby timer routing-disable Logical Interface Configuration Commands Broadcast-limit linkDisplay interface loopback Syntax display interface loopback number Syntax display interface mfr mfr-number Related command interface loopbackExample # View the status of Loopback Related command interface mfr Example # View the state information about MFR659 LMI Dlci Related command interface mp-group Example # View the state information of MP-group Related command interface null Display interface nullDisplay interface virtual-ethernet Syntax display interface null Example # View the state information about VT Related command interface virtual-ethernetExample # View the state information about VE Description of the fields of the display mfr command 663 Interface, state of the link layer, and the name Interface ethernet 665 Example # Create Loopback Related command display interface loopbackInterface loopback Interface null Example # Create MFRExample # Create MP-group Interface null Example # Enter Null 0 interface view Related command display interface nullInterface virtual-ethernet 669 Logical Interface Configuration Commands System view Cpos Interface Configuration CommandsController cpos Display controller cpos Display controller cpos cpos-number 673 This table, FRED, COFA, and SEF are alarm errors AERRsPossible error types Syntax display controller cpos cpos-numbere1 e1-number Display controller cpos e1Some information about T1 channels is omitted 675 Display controller cpos t1Syntax display controller cpos cpos-numbert1 t1-number VC-3 Example # Bundle timeslots on E1 channel 677 E1 set clock 679 Related command display controller cpos e1Example # Enable external payload loopback on E1 channel Syntax e1 e1-numbershutdown undo e1 e1-numbershutdown Syntax e1 e1-numberunframed undo e1 e1-numberunframed Syntax frame-format sdh sonet undo frame-format Undo flag j0 j1 c2Display controller cpos Multiplex mode Use the undo loopback command to remove a loopback# Enable external loopback on interface Cpos 1/0 Syntax multiplex mode au-3 au-4 undo multiplex mode 683 Related command frame-formatExample # In SDH mode, multiplex AUG to AU-3 Example # Shut down Cpos physical interface 1/0 Example # Bundle timeslots on T1 channel 685 Syntax t1 t1-numbershutdown Undo t1 t1-numbershutdown Related command display controller cpos t1Example # Enable external loopback on T1 channel Syntax t1 t1-numberunframed Undo t1 t1-numberunframed 687 Cpos Interface Configuration Commands ARP Configuration Commands Arp check enableSyntax arp check enable Undo arp check enable Arp max-learning-num Arp static Arp timer aging Related command reset arp, display arpRelated command display arp timer aging Display arp # Display the number of all ARP entries Related command arp static, reset arpDescription on the fields of the display arp command Display arp timer aging Arp static , and reset arp ExampleDisplay arp timer aging Arp timer aging Naturemask-arp enable Related command arp static and reset arpSyntax naturemask-arp enable Undo naturemask-arp enable Display arp vpn-instance Arp static and display arp Reset arpSpecified by the argument interface-type interface-number ARP Configuration Commands Gratuitous ARP Configuration Commands Gratuitous-arp-sending enableGratuitous-arp-learning enable Gratuitous-arp-sending enable Sysname system-view Sysname gratuitous-arp-learning enable ARP Source Suppression Configuration Commands Arp source-suppression enableArp source-suppression limit Display arp source-suppression Related command display arp source-suppression Display arp source-suppressionSyntax display arp source-suppression Description on fields of display arp source-suppression Authorized ARP Configuration Commands Arp authorized enableSyntax arp authorized enable Undo arp authorized enable Arp authorized time-out Authorized ARP Configuration Commands Proxy ARP Configuration Commands Proxy-arp enableLocal-proxy-arp enable Related command display proxy-arp Related command display local-proxy-arp Proxy-arp enableLocal-proxy-arp enable Display proxy-arp Dhcp Server Configuration Commands Bootfile-name Dhcp enableSyntax bootfile-name bootfile-name Undo bootfile-name Syntax dhcp enable Undo dhcp enable Dhcp select server global-pool Dhcp server detectSyntax dhcp server detect Undo dhcp server detect 707 Dhcp server forbidden-ip Dhcp server ip-pool Dhcp server ping timeout Related command dhcp enableDhcp server ping packets Example # Create the Dhcp address pool identified by Syntax dhcp update arp Undo dhcp update arp Dhcp server relay information enableDhcp update arp Reset dhcp server conflict Display dhcp server conflictDisplay dhcp server expired Display dhcp server conflict all ip ip-address Display dhcp server free-ip Display dhcp server forbidden-ipDisplay dhcp server free-ip Syntax display dhcp server forbidden-ip Reset dhcp server ip-in-use Display dhcp server ip-in-useBinding information of all address pools is displayed Information of Dhcp address pools or an IP address Reset dhcp server statistics Display dhcp server statisticsSyntax display dhcp server statistics Example # Display the statistics on the Dhcp server Display dhcp server tree Display dhcp server tree all pool pool-nameInformation of Dhcp address pools 715 Dns-list Undo dns-list ip-addressall Expired Related command dhcp server ip-poolDomain-name Gateway-list Netbios-type Related command dhcp server ip-pooland netbios-typeNbns-list 719 Undo network Related command dhcp server ip-pooland nbns-listNetwork 721 OptionUndo option code Reset dhcp server statistics Reset dhcp server conflictReset dhcp server ip-in-use Related command display dhcp server statistics Static-bind client-identifierExample # Clear the statistics of the Dhcp server 723 Static-bind ip-address 725 Static-bind mac-addressTftp-server domain-name Voice-config Undo voice-config as-ip fail-over ncp-ip voice-vlanTftp-server ip-address View Dhcp address pool view 727 Dhcp Server Configuration Commands Dhcp Relay Agent Configuration Commands Dhcp Snooping cannot be configured on the Dhcp relay agentSyntax dhcp relay address-check disable enable Dhcp relay address-check Dhcp relay information enable Dhcp relay information format Undo dhcp relay information strategy Dhcp relay information strategyDhcp relay information strategy drop keep replace Dhcp relay release ip Dhcp relay security staticSyntax dhcp relay release ip client-ip Undo dhcp relay security ip-address all dynamic static 733 Related command display dhcp relay securityDhcp relay security tracker Dhcp relay server-detect Dhcp relay server-groupDhcp relay server-detect Undo dhcp relay server-detect 735 Related command display dhcp relay server-groupDhcp relay server-select Dhcp update arp Dhcp select relayDhcp select relay Undo dhcp select relay Display dhcp relay Display dhcp relay securityServer group that a specified interface corresponds to Groups correlated to an interface or all interfaces Display dhcp relay security statistics Display dhcp relay security trackerDisplay dhcp relay security statistics Information about bindings of Dhcp relay agents Display dhcp relay server-group Display dhcp relay statisticsInterval is 10 seconds Syntax display dhcp relay server-group group-idall Server Client Reset dhcp relay statistics Reset dhcp relay statistics server-group group-idWhich to remove statistics from the relay agent Display dhcp relay statistics Dhcp Relay Agent Configuration Commands Dhcp Client Configuration Commands Description on fields of the display dhcp client command Ip address dhcp-alloc 745 Dhcp Client Configuration Commands Dhcp Snooping Configuration Commands Related command display dhcp-snoopingDhcp-snooping Dhcp-snooping trust Related command display dhcp-snooping trust Display dhcp-snoopingDisplay dhcp-snooping trust Dhcp-snooping Related command dhcp-snooping trust Example Trusted ports# Display information about trusted ports 749 Dhcp Snooping Configuration Commands Bootp Client Configuration Commands Bootp clientDisplay information about Bootp clients on all interfaces Including sub-interfaces and Vlan interfaces Ip address bootp-alloc Syntax ip address bootp-alloc Undo ip address bootp-allocRelated command display bootp client Description on fields of the display bootp client command Dhcp Debugging Commands Debugging dhcp server all error event packetUndo debugging dhcp server all error event packet Debugging dhcp server DHCPmessagetype Dhcp ACK Dhcp NAK 755 Checking for an expired leaseDHCP-DISCOVER packet received Checking whether the IP address 22.0.0.2 is in use DHCP-REQUEST message received Debugging dhcp relay Sending a DHCP-ACK message Sysname Terminal debugging 759 Debugging dhcp client all error event packet Undo debugging dhcp client all error event packetDebugging dhcp client Then broadcast it 761 State of the Dhcp client is changed from Halt to Init 763 Head Dhcp client starts address conflict detection using ARP ARP message sent DNS Configuration Commands Display dns domainDisplay dns dynamic-host Dns domain Example TTL Display dns proxy tableSyntax display dns proxy table Related command dns server Display dns serverDisplay ip host Syntax display dns server dynamic Dns proxy enable Related command display dns domainSyntax dns proxy enable Undo dns proxy enable Dns domain Dns resolve Dns serverSyntax dns resolve Undo dns resolve Syntax dns server ip-address Undo dns server ip-address Reset dns dynamic-host Related command display dns serverRelated command display ip host Syntax reset dns dynamic-host Related command display dns dynamic-host 771 DNS Configuration Commands IP Accounting Configuration Commands Display ip countDisplay ip count inbound-packets outbound-packets exterior Firewall-denied interior Ip count enable Syntax ip count enable Undo ip count enableDescription on fields of the display ip count rule command Display ip count rule Example # Enable IP accounting Ip count exterior-thresholdIp count firewall-denied 775 Ip count inbound-packets Ip count interior-threshold Example # Count incoming IP packets on Ethernet1/0# Specify not to count incoming IP packets on Ethernet1/0 777 Ip count outbound-packets Ip count rule Ip count timeout Reset ip countSyntax ip count timeout minutes Undo ip count timeout Syntax reset ip count all exterior firewall interior All Clears all statistics Exterior Clears the statistics from the exterior tableInterior Clears the statistics from the interior table # Clear the statistics of all IP packets IP Addressing Configuration Commands Display ip interface Description on fields of the display ip interface command Related command display ip interface Display ip interface briefExample # Display brief information about Ethernet 1/0 783 Displayed Ip address unnumbered 785 IP Addressing Configuration Commands IP Performance Configuration Commands Display fib # Display FIB information passing the IP prefix list abc0 Description on the fields of the display fib command# Display FIB information passing ACL Display fib ip-address Display fib statisticsFor description about the above output, refer to Table Syntax display fib statistics Example # Display Icmp statistics Display icmp statisticsSyntax display icmp statistics Display ip socket 1003072 # Display all socket information Syntax display ip statistics Description on the fields of the display ip socket commandDisplay ip statistics Display tcp statistics Example # Display statistics of IP packetsSyntax display tcp statistics 793 Related command display tcp status and reset tcp statistics Example # Display statistics of TCP traffic 795 Related command reset udp statistics Display tcp statusDisplay udp statistics Display tcp status Undo ip forward-broadcast Ip forward-broadcastIp forward-broadcast acl acl-number Ip redirects enable Ip ttl-expires enable Reset tcp statistics Ip unreachables enableReset ip statistics Reset udp statistics Tcp anti-naptha enableRelated command display tcp statistics Syntax reset udp statistics Tcp mss Tcp state Tcp syn-cookie enable Related command tcp anti-naptha enableThis support for this command varies with devices Syntax tcp syn-cookie enable Undo tcp syn-cookie enable Tcp timer check-state Tcp timer fin-timeoutExample # Enable the SYN Cookie feature 803 Related command tcp timer fin-timeoutand tcp window Tcp timer syn-timeoutRelated command tcp timer syn-timeoutand tcp window 805 Tcp windowSyntax tcp window window-size Undo tcp window IP Performance Configuration Commands IP Unicast Policy Routing Configuration Commands Apply default output-interfaceApply ip-address default next-hop View policy-based-route view Undo apply ip-address next-hop ip-address ip-address Parameters ip-address IP address of the default next hopApply ip-address next-hop Apply ip-precedence Examples # Set the next hop to 1.1.1.1 for matched packetsIP precedences and the corresponding keywords 809 Syntax display ip policy-based-route Apply output-interfaceDisplay ip policy-based-route Display ip policy-based-route setup 811 Local Displays statistics of enabled system policy routing Display ip policy-based-route statisticsInterface-number Routing statistics Related commands if-matchpacket-length Display policy-based-routeIf-match acl Syntax display policy-based-route policy-name Ip local policy-based-route Related commands if-match aclIf-match packet-length Related commands policy-based-route Related commands ip local policy-based-routeIp policy-based-route Policy-based-route Syntax reset policy-based-route statistics policy-name Reset policy-based-route statisticsRelated commands if-match acl and if-matchpacket-length 817 IP Unicast Policy Routing Configuration Commands UDP Helper Configuration Commands Reset udp-helper packetReset udp-helper packet Display udp-helper server Udp-helper port Udp-helper enableSyntax udp-helper enable Undo udp-helper enable 821 Related command display udp-helper serverUdp-helper server UDP Helper Configuration Commands Urpf Configuration Commands Ip urpf loose strict allow-default-route acl acl-numberIp urpf Undo ip urpf Urpf Configuration Commands Fast Forwarding Commands Display ip fast-forwarding cacheIp fast-forwarding Display ip fast-forwarding cache Fast Forwarding Commands 827 Reset ip fast-forwarding cacheSyntax reset ip fast-forwarding cache Fast Forwarding Commands IPV6 Basics Configuration Commands Display dns ipv6 dynamic-hostDisplay dns ipv6 server Syntax display dns ipv6 dynamic-host Syntax display ipv6 fib ipv6-address Display ipv6 fibExample # Display IPv6 DNS server information Description on fields of the display ipv6 fib command Display ipv6 fibcacheDisplay ipv6 host Syntax display ipv6 fibcache Display ipv6 interface Shutdown command 833 Display ipv6 neighbors Display ipv6 neighbors count Static vlan vlan-id count Description on fields of the display ipv6 pathmtu command Display ipv6 pathmtuDisplay ipv6 socket Syntax display ipv6 pathmtu ipv6-addressall dynamic static Description on fields of the display ipv6 socket command Display ipv6 statisticsSyntax display ipv6 statistics 837 Description on fields of the display ipv6 statistics command 839 Display tcp ipv6 statistics Display tcp ipv6 statisticsStatistics # Display the statistics of IPv6 TCP connections 841 Display tcp ipv6 status Syntax display tcp ipv6 status Display udp ipv6 statistics Syntax display udp ipv6 statistics843 TCP6CB Dns server ipv6 Ipv6Syntax ipv6 Undo ipv6 845 Ipv6 addressIpv6 address auto link-local Ipv6 address eui-64 Ipv6 address link-local Ipv6 fibcache Ipv6 fib-loadbalance-type hash-basedSyntax ipv6 fibcache Undo ipv6 fibcache 847 Ipv6 icmp-error Ipv6 host Ipv6 icmpv6 multicast-echo-reply enable Ipv6 mtuSyntax ipv6 mtu mtu-size Undo ipv6 mtu 849 Ipv6 nd autoconfig managed-address-flag Ipv6 nd autoconfig other-flagIpv6 nd autoconfig managed-address-flag Undo ipv6 nd autoconfig managed-address-flag Ipv6 nd dad attempts Ipv6 nd hop-limitSyntax ipv6 nd dad attempts value Undo ipv6 nd dad attempts Syntax ipv6 nd hop-limit value Undo ipv6 nd hop-limit Ipv6 nd ns retrans-timer Ipv6 nd nud reachable-time Ipv6 nd ra halt Syntax ipv6 nd ra halt Undo ipv6 nd ra haltOn a router # Suppress RA messages on Ethernet1/0 853 Ipv6 nd ra interval Ipv6 nd ra prefixUndo ipv6 nd ra interval Undo ipv6 nd ra prefix ipv6-prefix Ipv6 nd ra router-lifetime 855 Ipv6 neighbor Ipv6 neighbors max-learning-num Ipv6 pathmtuUndo ipv6 pathmtu ipv6-address 857 Reset dns ipv6 dynamic-host Related command display ipv6 pathmtuSyntax reset dns ipv6 dynamic-host Ipv6 pathmtu age Reset ipv6 pathmtu Reset ipv6 fibcacheReset ipv6 neighbors Reset ipv6 statistics Reset tcp ipv6 statisticsReset udp ipv6 statistics ICMPv6 packets Tcp ipv6 timer fin-timeout Tcp ipv6 timer syn-timeoutExample # Clear the statistics of all UDP packets 861 Tcp ipv6 window Syntax tcp ipv6 window size Undo tcp ipv6 window NAT-PT Configuration Commands Display natpt address-groupDisplay natpt address-mapping Display natpt address-group Display natpt aging-time Syntax display natpt aging-time Example # Display all NAT-PT configuration information Display natpt allDisplay natpt all 865 Display natpt frag-sessions Syntax display natpt frag-sessions Display natpt session Display natpt statisticsSyntax display natpt session all icmp tcp udp Display natpt statistics Natpt address-group Undo natpt address-group group-number Natpt aging-time Natpt enable Syntax natpt enable Undo natpt enableNatpt max-session Syntax natpt max-session max-number Undo natpt max-session Example # Configure a NAT-PT prefix Natpt prefixUndo natpt prefix natpt-prefix 871 Natpt turn-off tos Natpt turn-off traffic-classNatpt turn-off tos Undo natpt turn-off tos 873 Natpt v4bound dynamicNatpt v4bound static Natpt v6bound dynamic Reset natpt dynamic-mappings Syntax reset natpt dynamic-mappingsNatpt v6bound static Undo natpt v6bound static ipv6-addressipv4-address # Clear all NAT-PT statistics information Reset natpt statisticsReset natpt statistics Dual Stack Configuration Commands Ipv6 address auto link-local Automatically create a link-local address for an interfaceAutomatically created link-local address Ethernet interface view Example # Configure a link-local address on Ethernet 1/1 879 Dual Stack Configuration Commands Tunneling Configuration Commands Related command interface tunnel and sourceDestination Undo destination Example # Display information of the interface tunnel Display interface tunnelSyntax display interface tunnel number 883 Display ipv6 interface tunnelSyntax display ipv6 interface tunnel number Encapsulation-limit Interface tunnelSyntax encapsulation-limit number Undo encapsulation-limit Syntax interface tunnel number 885 Undo interface tunnel numberExample # Create the interface tunnel Undo source Related command interface tunnel and destinationSource Undo tunnel-protocol Tunnel-protocolIpv4-ipv6 Tunneling Configuration Commands View IPv6 policy-based-route view IPV6 Unicast Policy Routing Configuration CommandsApply destination-based-forwarding Apply ipv6-address default next-hop Apply ipv6-address next-hop Apply ipv6-precedenceExample # Set a next hop of 11 for matched IPv6 packets Preferences and the corresponding keywords Apply output-interface Display ipv6 config policy-based-route Syntax display ipv6 config policy-based-route policy-nameDisplay ipv6 policy-based-route Display ipv6 policy-based-route Display ipv6 policy-based-route setup Local Displays system policy routing information Related command if-matchpacket-length Display ipv6 policy-based-route statisticsIf-match acl6 Syntax if-match acl6 acl6-number Undo if-match acl6 Example # Permit the packets matching ACL Related command if-match acl6Ipv6 local policy-based-route Related command ipv6 local policy-based-route Ipv6 policy-based-route interface viewIpv6 policy-based-route system view 897 IPV6 Unicast Policy Routing Configuration Commands Terminal Access Configuration Commands Auto-closeAuto-link Syntax auto-close time Undo auto-close Bind vpn-instance Syntax bind vpn-instance vpn-name Undo bind vpn-instance Data protect router-unix Data read blockView Terminal template view Syntax data read block Undo data read block Display rta Data send delaySyntax data send delay milliseconds Undo data send delay # Display brief information about TTY 903 TTY # Display all the information about terminal access Description on the fields of the display rta all command# Display statistics about terminal 905 # Display terminal access statistics Driverbuf saveDriverbuf size Syntax driverbuf save Undo driverbuf save Idle-timeout Syntax idle-timeout seconds Undo idle-timeoutUndo driverbuf size 907 Related command print information and print menu Menu hotkeyMenu screencode Syntax menu hotkey ascii-code&1-3 Undo menu hotkey 909 Print connection-infoSyntax print connection-info Undo print connection-info Related command print information Related command print connection-infoand print menuPrint information Print menu Print language RedrawkeyPrint language chinese english Terminal template view Reset rta statistics terminal-number Reset rta connectionReset rta statistics Resetkey Related command display rtaUndo resetkey Rta bind Rta rtc-server listen-port Rta server enable Syntax rta server enable Undo rta server enableRta source-ip Syntax rta source-ip ip-address Undo rta source-ip Rta template Rta terminalHiding TCP connections 917 Sendbuf bufsizeSyntax sendbuf bufsize size Undo sendbuf bufsize Syntax sendbuf threshold value Undo sendbuf threshold Sendbuf thresholdTcp # Disable TCP delay Testkey# Set the TCP send buffer size to 512 bytes Undo testkey Update changed-config AccessUpdate changed-config Values are used for the hotkeys of flow control Vty description Vty hotkeyUndo vty vty-numberdescription 921 Vty password 923 Vty rtc-client remoteVty rtc-server remote Undo vty vty-numberscreencode Related command menu screencodeVty screencode Vty telnet remote Vty tty remoteExample # Set the screen code for VTY 1 to E!9Q 925 Vty-switch priority Vty-switch thresholdSyntax vty-switch priority Undo vty-switch priority Syntax vty-switch threshold times Undo vty-switch threshold 927 Terminal Access Configuration Commands IP Routing Table Commands Bandwidth-based-sharingDisplay ip routing-table Syntax bandwidth-based-sharing Undo bandwidth-based-sharing Special characters for regular expressions String, the end of a string 931 Display ip routing-table acl Syntax display ip routing-table acl acl-number verbose 933 IP Routing Table Commands Display ip routing-table ip-address 935 Display ip routing-table ip-address Display ip routing-table ip-address maskDisplay ip routing-table ip-addresslonger-match Display ip routing-table ip-address mask longer-match 937 Display ip routing-table ip-prefix 939 Display ip routing-table protocolFor detailed description of the above output, see Table View Any view Display ip routing-table statistics# Display summary information about static routes Display ip relay-route Display ip relay-tunnelDisplay ip relay-route vpn-instance vpn-instance-name # Display recursive route information Display load-sharing ip address Display ipv6 routing-tableExamples # Display recursive tunnel information Syntax display ipv6 routing-table 943 Display ipv6 routing-table aclSyntax display ipv6 routing-table acl acl6-number verbose Display ipv6 routing-table ipv6-addressprefix-length Display ipv6 routing-table ipv6-addressRefer to for description about the above output Display ipv6 routing-table ipv6-address1 ipv6-address2 945 Display ipv6 routing-table ipv6-prefix Display ipv6 routing-table protocol Display ipv6 routing-table statistics Syntax display ipv6 routing-table statistics# Display routing statistics 947 Display ipv6 routing-table verbose Display ipv6 relay-routeDisplay ipv6 routing-table verbose Entire routing table and information for each route Display ipv6 relay-tunnel Display ipv6 relay-tunnel# Display IPv6 recursive tunnel information 949 Syntax load-bandwidth bandwidth Undo load-bandwidth Reset load-sharingLoad-bandwidth Reset ip routing-table statistics protocol Reset ipv6 routing-table statisticsReset ipv6 routing-table statistics protocol all protocol Ripng , or static Sysname reset ipv6 routing-table statistics protocol all BGP Configuration Commands Configuration Commands onAggregate Functions of the keywords If-match clause of the route-policy command Balance BGP/BGP-VPN instance viewSyntax balance number Undo balance Suppress-policy Related commands display bgp routing-table Bestroute as-path-neglect BGP/BGP-VPN instance viewView BGP view/BGP-VPN instance view 955 Comparison is not enabled by default Bestroute compare-med BGP/BGP-VPN instance viewBestroute med-confederation BGP/BGP-VPN instance view Syntax bestroute compare-med Undo bestroute compare-med 957 BgpCompare-different-as-med BGP/BGP-VPN instance view Confederation id Syntax confederation id as-number Undo confederation id Related commands confederation id and confederation peer-as Confederation nonstandardConfederation peer-as View BGP view Dampening BGP/BGP-VPN instance view Undo confederation peer-as as-number-listExamples # Specify confederation peer sub ASs 2000 Undo dampening Default ipv4-unicast Examples # In BGP view, configure BGP route dampeningSyntax default ipv4-unicast Undo default ipv4-unicast 961 Syntax default med med-value Undo default med Default local-preference BGP/BGP-VPN instance viewDefault med BGP/BGP-VPN instance view 963 Default-route imported BGP/BGP-VPN instance viewSyntax default-route imported Undo default-route imported Related commands import-routeBGP/BGP-VPN instance view Description on the fields of the display bgp group commandDisplay bgp group Syntax display bgp group group-name Advertised with the network command Display bgp networkDisplay bgp network # Display routing information that has been advertised Description on the fields of the display bgp paths command Display bgp pathsDisplay bgp peer MED Description on the fields of the display bgp peer command 967 Description on the fields of the display bgp routing command Display bgp routing-table Display bgp routing-table as-path-acl 969 Display bgp routing-table cidr Display bgp routing-table cidr 971 Display bgp routing-table communityDisplay bgp routing-table community-list Display bgp routing-table dampened Display bgp routing-table dampenedDampened BGP routes # Display dampened BGP routes Related commands dampening BGP/BGP-VPN instance view Display bgp routing-table dampening parameterDisplay bgp routing-table different-origin-as Display bgp routing-table dampening parameter Display bgp routing-table flap-info Longer-match 975 Related commands display bgp peerDisplay bgp routing-table peer Display bgp routing-table regular-expression Display bgp routing-table statisticEbgp-interface-sensitive Display bgp routing-table statistic 977 Filter-policy export BGP/BGP-VPN instance viewUndo ebgp-interface-sensitive Filter-policy import BGP/BGP-VPN instance view Graceful-restart timer restart Graceful-restart BGP viewSyntax graceful-restart Undo graceful-restart 979 Graceful-restart timer wait-for-rib Graceful-restart timer wait-for-rib timerUndo graceful-restart timer wait-for-rib Using this command can speed up route convergence Import-route BGP/BGP-VPN instance view 981 Log-peer-change Syntax log-peer-change Undo log-peer-change Network BGP/BGP-VPN instance view 983 Peer advertise-community BGP/BGP-VPN instance view Peer advertise-ext-community BGP/BGP-VPN instance view 985 Related commands display bgp routing-table peerPeer allow-as-loop BGP/BGP-VPN instance view Undo peer ip-address Peer as-number BGP/BGP-VPN instance viewPeer as-path-acl BGP/BGP-VPN instance view Peer capability-advertise conventional 987 Peer capability-advertise route-refresh Peer default-route-advertise BGP/BGP-VPN instance view Undo peer group-nameip-address default-route-advertisePeer connect-interface BGP/BGP-VPN instance view Undo peer group-name ip-address connect-interface Peer description BGP/BGP-VPN instance view Peer ebgp-max-hop BGP/BGP-VPN instance view 991 Peer fake-as BGP/BGP-VPN instance view Peer enable BGP viewSyntax peer ip-addressenable Undo peer ip-addressenable 993 Related commands peer as-path-aclBGP/BGP-VPN instance viewPeer filter-policy BGP/BGP-VPN instance view Peer group BGP/BGP-VPN instance view 995 Peer ignore BGP/BGP-VPN instance viewPeer ip-prefix Peer keep-all-routes BGP/BGP-VPN instance view Peer log-change BGP/BGP-VPN instance view Peer next-hop-local BGP/BGP-VPN instance viewUndo peer group-name ip-address next-hop-local View BGP view /BGP-VPN instance view Peer password # Perform the similar configuration on the peer Peer preferred-value BGP/BGP-VPN instance viewUndo peer group-name ip-address preferred-value 999 Peer public-as-only BGP/BGP-VPN instance view Undo peer group-name ip-address public-as-only Peer reflect-client BGP/BGP-VPN instance view 1001 Peer route-limit BGP/BGP-VPN instance view Peer route-policy BGP/BGP-VPN instance view Peer route-update-interval BGP/BGP-VPN instance view 1003 Peer substitute-as BGP/BGP-VPN instance view Undo peer group-nameip-address substitute-as 1005 Peer timer BGP/BGP-VPN instance viewRelated commands timer BGP/BGP-VPN instance view Preference BGP/BGP-VPN instance view Reflect between-clients BGP viewUndo preference Syntax reflect between-clients Undo reflect between-clients Examples # Disable route reflection between clients Reflector cluster-id BGP viewExamples # Set the cluster ID to 1007 Reset bgp All Resets all BGP connectionsAs-number Resets BGP connections to peers in the AS Refresh bgp 1009 Reset bgp dampeningReset bgp flap-info Reset bgp ipv4 all Syntax reset bgp ipv4 allRouter-id Syntax router-id router-id Undo router-id 1011 Summary automaticSyntax summary automatic Undo summary automatic Timer BGP/BGP-VPN instance view Syntax timer keepalive keepalive hold holdtime Undo timerSynchronization BGP view Syntax synchronization Undo synchronization Related commands peer timer BGP/BGP-VPN instance view 1013 BGP Configuration Commands BGP Debugging Commands Debugging bgp all BGP configuration information BGP received an Open message from the peer 1017 Debugging bgp detailSyntax debugging bgp detail Undo debugging bgp detail Debugging bgp event Route was deleted from the instance BGP has received an Update message Debugging bgp graceful-restartState has changed from Opensent to Openconfirm 1019 BGP GR Helper received an EOR message from peer BGP neighbor 10.1.1.1 is performing GRBGP peer relationship has been successfully established 1021 Description on the fields of the debugging bgp commandDebugging bgp Description on the fields of the debugging bgp open command Information about the sent BGP Open messageAFI/ Safi WTR Information about the received BGP Open message Information about the sent BGP Keepalive messageInformation about the received BGP Keepalive message 1023 Debugging bgp timer ConnectRetry timer for BGP peer 2.2.2.2 expired Hold timer expired on BGP peer Receive Enables the debugging for received BGP packetsSend Enables the debugging for sent BGP packets Update messages Ip-prefix ip-prefix-name receive send verbose Debugging bgp update ipv4Ip-prefix-name receive send verbose 1027 Debugging bgp update ipv6Update messages of IPv4 address family Receive Enables/disables debugging for received BGP packets Send Enables/disables debugging for sent BGP packetsFor IPv6 BGP update messages Complete By default, this debugging is disabled Debugging bgp update l2vpn Update messages of IPv6 address familyVerbose Send verbose Debugging bgp update label-route Update messages in an L2VPN environmentAcl-number ip-prefix ip-prefix-name receive send verbose Receive send verbose Update message information of L3VPN labeled routes 1031 Debugging bgp update peer Update message information of IPv6 labeled routes Debugging bgp update vpls Vpls Update messagesFor BGP Vpls Update messages 1033 Information about the received Vpls update message Debugging bgp update vpn-instanceInformation about the sent Vpls update message Debugging bgp update vpnv4 BGP VPNv4 Update messagesFor BGP VPNv4 Update messages Examples None Update message information of VPNv4 IS-IS Configuration Commands Area-authentication-modeArea-authentication-mode simple md5 password ip osi Undo area-authentication-mode Auto cost enable Syntax auto-cost enable Undo auto-cost enableRelated commands bandwidth-referenceIS-IS view, cost-style Bandwidth-reference IS-IS view 1039 Related commands auto cost enableCircuit-cost Related commands isis cost, cost-style Cost-styleRelax-spf-limit Undo cost-style 1041 Default-route-advertise IS-IS viewRelated commands isis cost Description on the fields of the display isis brief command Display isis brief Display isis debug-switches Display isis graceful-restart status Display isis interface Traffic-eng Displays IS-IS traffic engineering informationVerbose Displays IS-IS interface detail information Tunnel Displays IS-IS tunnel information Examples # Display IS-IS enabled interface information # Display detailed IS-IS interface information1045 DIS BFD Display isis licenseSyntax display isis license Display isis lsdb License information varies with device models ATT/P/OL Display isis mesh-groupLspid # Display the configuration information of IS-IS mesh-group # Configure a static mapping for the remote IS-IS systemDisplay isis name-table Display isis peer Display isis route Up state and direct interface’s IP address# Display detailed IS-IS neighbor information PRI 1051 Description on the fields of the display isis route command# Display IS-IS IPv4 routing information Display isis spf-log Display isis statistics Domain-authentication-mode Simple Specifies to send the password in plain textMd5 Specifies to send the password encrypted with MD5 IS-IS view Filter-policy export IS-IS view 1055 Related commands filter-policy import IS-IS view Filter-policy import IS-IS view Related commands filter-policy export IS-IS view Flash-floodLevel-1 level-2 Undo flash-flood level-1 level-2 Graceful-restart Graceful-restart IS-IS viewGraceful-restart interval IS-IS view Graceful-restart suppress-sa Import-route IS-IS viewGraceful-restart suppress-sa Undo graceful-restart suppress-sa Related commands import-route isis level-2 into level-1 Related commands import-routeIS-IS view Import-route isis level-2 into level-1Examples # Redistribute static routes and set the cost to Undo import-route isis level-2 into level-1 Isis authentication-mode Isis This command is not available in loopback interface view Isis circuit-level level-1 level-1-2 level-2Undo isis circuit-level 1063 Syntax isis circuit-type p2p Undo isis circuit-type Related commands is-levelIsis circuit-type Syntax isis dis-name symbolic-name Undo isis dis-name Isis costIsis dis-name 1065 Examples # Configure the name as Localarea for the local LAN Isis dis-priority Isis enable Syntax isis enable process-id Undo isis enableRelated commands isis, network-entity Isis mesh-group Isis peer-ip-ignore Syntax isis peer-ip-ignore Undo isis peer-ip-ignore Isis small-hello Syntax isis silent Undo isis silentSyntax isis small-hello Undo isis small-hello 1069 Isis timer csnp Isis timer hello Undo isis timer holding-multiplier level-1 level-2 Isis timer holding-multiplierIsis timer holding-multiplier value level-1 level-2 Isis timer lsp Related commands isis timer helloSyntax isis timer lsp time count count Undo isis timer lsp Related commands isis timer retransmit Isis timer retransmit Related commands Examples Isis timer lspIs-level Syntax is-level level-1 level-1-2 level-2 Undo is-level Related commands isis circuit-level Examples # Configure the router to work in Level-1Is-name Syntax is-name sys-name Undo is-name Is-snmp-traps enable Syntax is-snmp-traps enable Undo is-snmp-trapsIs-name map Undo is-name map sys-id Log-peer-change IS-IS view Lsp-fragments-extend Lsp-length originate 1077 # Restore the default Lsp-length receiveMaximum load-balancing IS-IS view Syntax lsp-length receive size Undo lsp-length receive Related commands Isis, isis enable Examples Network-entityPreference IS-IS view Network-entity net Reset isis all Examples # Clear all IS-IS data structure information Reset isis peer Set-overloadAllow interlevel external Undo set-overload Spf-slice-size Syntax spf-slice-size duration-time Undo spf-slice-size Summary IS-IS view 1083 Timer isp-generation Undo timer lsp-generation level-1 level-2Generation interval Interval Timer lsp-max-age Timer lsp-refreshSyntax timer lsp-max-age seconds Undo timer lsp-max-age Related commands timer lsp-refresh Timer spf Related commands timer lsp-max-ageUndo timer spf Examples # Set the LSP refresh interval to 1500 seconds Virtual-system # Set the maximum SPF calculation interval to 15 secondsUndo virtual-system virtual-system-id 1087 IS-IS Configuration Commands IS-IS Debugging Commands Event Enables IS-IS event debuggingDebugging isis Ha-events interface-information memory-allocating IS-IS Debugging Commands 1091 Snpa Snpa Field CircuitName not enabled 1093 SNP packet length mismatch 1095 Length length Updt Reset Required 1097 Sending pduLevel pduType on circuitName Sending pduLevel Csnp PDU fails 1099 Tent New Distance from RootNodeSourceId 1101 LSP LevelType LSP level, which can be L1 or L2 1103 IP address took effect on the IS-IS interface Router B sent Csnp packets 1105 IS-IS Debugging Commands Ospf Configuration Commands Related commandsL3VPN Configuration Commands on Abr-summary Ospf area view Area Ospf view Asbr-summarySyntax area area-id Undo area area-id Authentication-mode Simple Specifies the simple authentication modeDisplay ospf asbr-summary View Ospf area view Default Related commands ospf authentication-modeSyntax default cost cost limit limit tag tag type type Bandwidth-reference Ospf view Default-cost Ospf area view Undo default cost limit tag typeRelated commands import-route Ospf view Syntax default-cost cost Undo default-cost Default-route-advertise Ospf view Related commands stub Ospf area view, nssaDefault-route-advertise summary cost cost Undo default-route-advertise Description OSPF/OSPF area view Display ospf abr-asbrSyntax description description Undo description # Describe the Ospf area0 as bone area Display ospf asbr-summary Related commands asbr-summary Display ospf briefSyntax display ospf process-id brief Examples # Display Ospf brief information Description on the fields of the display ospf brief command Mpls TE 1117 Display ospf cumulativeSyntax display ospf process-id cumulative Display ospf error Syntax display ospf process-id errorNssa ASE/NSSA Description on the fields of the display ospf error command 1119 Display ospf interface BDR Display ospf lsdb1121 Description on the fields of the display ospf lsdb command # Display Type2 LSA Network LSA information in the Lsdb Display ospf nexthop Syntax display ospf process-id nexthop1123 LS ID Display ospf peer Description on the fields of the display ospf peer command Display ospf peer statistics# Display brief Ospf neighbor information Syntax display ospf process-id peer statistics Display ospf request-queue Keep neighbor relationship Init 1127 Display ospf retrans-queueExamples # Display Ospf request list information Display ospf routing Description on the fields of the display ospf vlink command Display ospf vlinkSyntax display ospf process-id vlink 1129 Enable link-local-signaling Enable logError Enables error logging State Enables state logging 1131 Enable out-of-band-resynchronizationFilter import/export By default, Summary LSAs filtering is disabled This command is only available on an ABRFilter-policy export Ospf view Undo filter-policy export protocol process-id Examples # Filter redistributed routes using ACL Filter-policy import Ospf viewGraceful-restart Ospf view 1133 Examples # Enable Ietf Graceful Restart for Ospf process # Enable non-IETF Graceful Restart for Ospf processGraceful-restart help Syntax graceful-restart help acl-numberprefix prefix-list Related commands ospf timer dead Graceful-restart interval Ospf viewHost-advertise 1135 Import-route Ospf view Related commands Examples Default-route-advertise Ospf viewImport-route command cannot redistribute default routes 1137 Related commands lsa-generation-interval Lsa-arrival-interval Related commands lsa-arrival-interval Lsa-generation-intervalLsdb-overflow-limit Undo lsa-generation-interval Number Maximum route number in the range 1 to Maximum load-balancing Ospf viewMaximum-routes Related commands ospf Network Ospf area viewNssa 1141 Opaque-capability enable Related commands default-cost Ospf area viewExamples # Configure area1 as an Nssa area Syntax opaque-capability enable Undo opaque-capability Ospf authentication-mode OspfUndo ospf process-id 1143 Related commands authentication-mode 1145 Ospf costSyntax ospf cost value Undo ospf cost Ospf dr-priority Ospf mib-bindingSyntax ospf dr-priority priority Undo ospf dr-priority Syntax ospf mib-binding process-id Undo ospf mib-binding Ospf mtu-enable Ospf network-type Ospf timer dead Related commands ospf dr-priorityThis command is not supported on the Null interface Syntax ospf timer dead seconds Undo ospf timer dead Ospf timer hello Related commands ospf timer helloSyntax ospf timer hello seconds Undo ospf timer hello 1149 Syntax ospf timer poll seconds Undo ospf timer poll Ospf timer pollOspf timer retransmit Ospf trans-delay Syntax ospf trans-delay seconds Undo ospf trans-delayPeer 1151 Command sets priority for internal routes PreferenceExamples # Specify the neighbor IP address Preference ase route-policy route-policy-name value Reset ospf counters Reset ospf processSyntax reset ospf process-id process 1153 Reset ospf redistribution Syntax reset ospf process-id redistributionRfc1583 compatible Syntax rfc1583 compatible Undo rfc1583 compatible Snmp-agent trap enable ospf Silent-interface Ospf view Ospf Configuration Commands Spf-schedule-interval Stub Ospf area viewUndo spf-schedule-interval Syntax stub no-summary Undo stub Default-cost Ospf area view Stub-routerStub-router Undo stub-router 1159 Examples # Enable a stub-routerVlink-peer Ospf area view Related commands authentication-mode,display ospf peer RIP Configuration Commands Default cost RIP viewSyntax default cost value Undo default cost Checkzero Default-route originate Related commands import-route RIP view# Disable default route sending Display rip Description on the fields of the display rip command 1163 Description on fields of the display rip database command Display rip databaseSyntax display rip process-iddatabase X.X/X 1165 Display rip interfaceDisplay rip route RIP Configuration Commands Description on the fields of the display rip route command Filter-policy export RIP view# Display the routing statistics of RIP process 1167 Examples # Reference ACL 2000 to filter outbound routes Filter-policy import RIP viewInterface-type interface-number Specifies an interface 1169 Host-routeSyntax host-route Undo host-route Including bgp , direct , isis , ospf , rip , rip and static Default cost RIP viewImport-route RIP view 1171 # Set the default cost for redistributed routes toMaximum load-balancing RIP view Syntax peer ip-address Reset rip statistics Syntax reset rip process-idstatisticsRip 1173 Rip authentication-mode Undo rip authentication-mode Mode and parameters By default, an interface is enabled to receive RIP messages# Enable Ethernet1/0 to receive RIP messages Format defined in RFC Related commands rip metricout Related commands rip metricinRip metricin Rip metricout Rip mib-binding Rip outputSyntax rip mib-binding process-id Undo rip mib-binding Syntax rip output Undo rip output Rip split-horizon Related commands rip inputRip poison-reverse Examples # Enable the split horizon function on Ethernet1/0 Related commands summaryRip summary-address Rip triggered Rip version Undo rip triggeredRip version 1 2 broadcast multicast Undo rip version Silent-interface RIP view All Silents all interfacesMessages 1181 Timers Related commands rip versionSummary Syntax summary Trip retransmit count 1183 Undo trip retransmit timer Trip retransmit timerTrip retransmit timer retransmit-time-value Validate-source-address VersionSyntax validate-source-address Undo validate-source-address Version 1 Sysname system-view Sysname rip Sysname-rip-100 version Routing Policy Common Configuration Commands Apply as-pathApply comm-list delete Syntax apply comm-list comm-list-numberdelete Apply community Undo apply comm-list Apply cost Syntax apply cost + value Undo apply costView Routing policy view Parameters + Increases cost value. + Decreases cost value Apply cost-type Apply extcommunity No level is set by default Apply isisApply isis level-1 level-1-2 level-2 Undo apply isis 1191 Related commands route-policy Apply local-preferenceApply mpls-label Syntax apply mpls-label Undo apply mpls-label Apply origin Apply preferenceSyntax apply preference preference Undo apply preference 1193 Syntax apply tag value Undo apply tag Apply preferred-valueApply tag Display ip as-path Syntax display ip as-path as-path-acl numberExamples # Display the information of BGP AS path ACL 1195 Syntax display ip extcommunity-list ext-comm-list-number Display ip community-listDisplay ip extcommunity-list Display route-policy If-match as-pathSyntax display route-policy route-policy-name Examples # Display the information of routing policy If-match community Related commands route-policy,ip as-pathaclRelated commands route-policyand ip community-list If-match cost If-match extcommunitySyntax if-match cost value Undo if-match cost 1199 If-match interface If-match mpls-label If-match route-type If-match tag Ip as-pathSyntax if-match tag value Undo if-match tag Undo ip as-path as-path-number Ip community-list 1203 Sysname system-view Sysname ip community-list 100 permit Ip extcommunity-list Route-policyUndo ip extcommunity-list ext-comm-list-number 1205 Routing Policy Common Configuration Commands Syntax display ip ip-prefix ip-prefix-name IPV4 Routing Policy Configuration CommandsDisplay ip ip-prefix Related commands ip ip-prefix Examples # Display the statistics of IPv4 prefix list abc If-match ip-prefix Related commands Route-policy ExamplesIf-match ip Ip ip-prefix 1211 Reset ip ip-prefixSyntax reset ip ip-prefix ip-prefix-name IPV4 Routing Policy Configuration Commands IPV6 Routing Policy Configuration Commands Apply ipv6 next-hopDisplay ip ipv6-prefix Syntax display ip ipv6-prefix ipv6-prefix-name If-match ipv6 Next-hop Matches the next hop of IPv6 routing informationString of 1 to 19 characters Address based match criterion for IPv6 routes Ip ipv6-prefix 1215 Examples # Clear the statistics of IPv6 prefix list abc Reset ip ipv6-prefixSyntax reset ip ipv6-prefix ipv6-prefix-name Static Routing Configuration Commands Delete static-routes allIp route-static Examples # Delete all static routes on the router Configured gateway-address Must be identical to that configured in the NQA test group Ethernet interface and Vlan interfaceAssociate it with a Track entry 1219 Ip route-static default-preference Examples # Set the default preference of static routes to IPV6 BGP Configuration Commands Related commands display ipv6 routing-tableonBalance IPv6 address family view Bestroute as-path-neglect IPv6 address family view Bestroute compare-med IPv6 address family view Bestroute med-confederation IPv6 address family view Compare-different-as-med IPv6 address family view 1223 Dampening IPv6 address family view 1225 Default local-preferenceIPv6 address family viewDefault med IPv6 address family view Syntax display bgp ipv6 group ipv6-group-name Default-route imported IPv6 address family viewDisplay bgp ipv6 group 1227 Display bgp ipv6 networkSyntax display bgp ipv6 network Display bgp ipv6 paths Syntax display bgp ipv6 paths as-regular-expression Incomplete Display bgp ipv6 peer1229 Display bgp ipv6 routing-table Field Description Local router ID Display bgp ipv6 routing-table as-path-acl 1231 Display bgp ipv6 routing-table community Examples # Display routes filtered through the AS path ACL Display bgp ipv6 routing-table community-list Display bgp ipv6 routing-table dampenedSyntax display bgp ipv6 routing-table dampened Examples # Display IPv6 BGP dampened routes Display bgp ipv6 routing-table dampening parameter Display bgp ipv6 routing-table different-origin-asSyntax display bgp ipv6 routing-table dampening parameter Syntax display bgp ipv6 routing-table different-origin-as Display bgp ipv6 routing-table flap-info Examples # Display IPv6 BGP routes from different ASsExamples # Display IPv6 BGP route flap statistics 1235 Command Display bgp ipv6 routing-table labelSyntax display bgp ipv6 routing-table label Examples # Display IPv6 BGP label routing information 1237 Display bgp ipv6 routing-table peerDisplay bgp ipv6 routing-table regular-expression Display bgp ipv6 routing-table statistic Filter-policy exportIPv6 address family viewParameters as-regular-expression AS regular expression Syntax display bgp ipv6 routing-table statistic Filter-policy import IPv6 address family view 1239 Group IPv6 address family view Import-route IPv6 address family viewExamples # Reference ACL6 2001 to filter all inbound routes Syntax group ipv6-group-name internal external Ipv6-family Network IPv6 address family viewSyntax ipv6-family Undo ipv6-family 1241 Peer advertise-community IPv6 address family view 1243 Peer advertise-ext-community IPv6 address family viewPeer allow-as-loop IPv6 address family view Peer as-number IPv6 address family view 1245 Peer as-path-acl IPv6 address family viewImport export Peer connect-interface IPv6 address family view 1247 Peer default-route-advertisePeer description IPv6 address family view Peer ebgp-max-hop IPv6 address family view 1249 Peer enable IPv6 address family viewPeer fake-as IPv6 address family view Peer filter-policy IPv6 address family view 1251 Peer group IPv6 address family viewPeer ignore IPv6 address family view Peer ipv6-prefix 1253 Peer keep-all-routes IPv6 address family viewPeer label-route-capability IPv6 address family view Peer log-change IPv6 address family view Peer next-hop-local IPv6 address family view Peer preferred-value IPv6 address family view 1255 Peer public-as-only IPv6 address family view Peer reflect-client IPv6 address family view Peer route-limit IPv6 address family view 1257 Peer route-update-interval IPv6 address family view Peer route-policy IPv6 address family view 1259 Undo peer ipv6-group-nameipv6-address route-update-intervalPeer substitute-as IPv6 address family view Preference IPv6 address family view Peer timer IPv6 address family viewRelated commands timer IPv6 address family view Reflect between-clients IPv6 address family view 1261 Refresh bgp ipv6 Examples # Enable route reflection between clientsReflector cluster-id IPv6 address family view Reset bgp ipv6 1263 Reset bgp ipv6 dampening Reset bgp ipv6 flap-info Synchronization IPv6 address family view 1265 Timer IPv6 address family view Related commands peer timer IPv6 address family view 1267 IPV6 BGP Configuration Commands IPV6 IS-IS Configuration Commands # Display detailed IPv6 IS-IS routing information Ipv6 default-route-advertise 1271 Ipv6 enable Syntax ipv6 enable Undo ipv6 enableIpv6 filter-policy export Undo ipv6 filter-policy export protocol process-id Related commands ipv6 filter-policy import Ipv6 filter-policy importUndo ipv6 filter-policy import 1273 Related commands ipv6 filter-policy export Ipv6 import-route 1275 Ipv6 import-route isisv6 level-2 into level-1Undo ipv6 import-route isisv6 level-2 into level-1 Ipv6 maximum load-balancing Ipv6 preference Ipv6 summary 1277 Syntax isis ipv6 enable process-id Undo isis ipv6 enable Isis ipv6 enableExamples # Configure a summary route of 2002/32 Area OSPFv3 view IPV6 OSPFV3 Configuration CommandsAbr-summary OSPFv3 area view Default cost Default-cost OSPFv3 area viewSyntax default-cost value Examples # Enter OSPFv3 Area 0 view Related commands stubOSPFv3 area view Display debugging ospfv3Display debugging ospfv3 Debugging state information Syntax display ospfv3 process-id Description on the fields of the display isofv3 commandDisplay ospfv3 Display ospfv3 interface 1283 Display ospfv3 lsdb # Display Link-local LSA information in the Lsdb 1285 Display ospfv3 lsdb statistic Syntax display ospfv3 lsdb statistic Display ospfv3 next-hop Display ospfv3 peerSyntax display ospfv3 process-id next-hop Interface-type interface-number interface type and number Description on the fields of the display isofv3 peer command Display ospfv3 peer statistic Display ospfv3 request-listSyntax display ospfv3 peer statistic Syntax display ospfv3 process-id request-list statistics Display ospfv3 retrans-list # Display the statistics of OSPFv3 link state request listSyntax display ospfv3 process-id retrans-list statistics LS-ID Display ospfv3 routing 1291 # Display the statistics of OSPFv3 routing table Display ospfv3 statistic Display ospfv3 topologySyntax display ospfv3 statistic Syntax display ospfv3 process-id topology area area-id Display ospfv3 vlink Syntax display ospfv3 process-id vlink Filter-policy exportOSPFv3 view 1295 Filter-policy importOSPFv3 view Routes that fail to pass are not added to the routing table Import-routeOSPFv3 view Allow-ibgp direct static cost value type type route-policyDirect static Both Ebgp and Ibgp routes Maximum load-balancingOSPFv3 view Process Related commands router-id Ospfv3Ospfv3 area Undo ospfv3 process-id Ospfv3 cost Ospfv3 dr-priority 1301 Ospfv3 timer deadOspfv3 mtu-ignore Ospfv3 timer hello Related commands ospfv3 timer hello Ospfv3 timer retransmit Ospfv3 trans-delayRelated commands ospfv3 timer dead 1303 Preference ase route-policy route-policy-name preference Related commands Ospfv3 Silent-interfaceOSPFv3 viewRouter-id router-id OSPFv3 processes on a router Spf timers Undo spf timers Related commands default cost Examples # Configure OSPFv3 area 1 as a stub areaUndo vlink-peer router-id hello retransmit trans-delay dead StubOSPFv3 area view IPV6 OSPFV3 Configuration Commands IPV6 Ripng Configuration Commands Default cost RIPng viewSyntax default cost cost Undo default cost View RIPng view Syntax display ripng process-id Related commands import-routeDisplay ripng Description on the fields of the display ripng command Description on fields of the display ripng database commandDisplay ripng database Syntax display ripng process-iddatabase Display ripng interface 1313 Display ripng routeSyntax display ripng process-idroute Filter-policy export Filter-policy import RIPng view Import-route 1315 Related commands default cost on Maximum load-balancing RIPng view # Restore the default RIPng route priority # Disable RIPng processRipng Undo ripng process-id Syntax ripng process-idenable Undo ripng enable Ripng default-routeRipng enable Related commands ripng metricout Ripng metricinRipng metricout Syntax ripng metricin value Undo ripng metricin Related commands ripng metricin Ripng poison-reverseRipng split-horizon Syntax ripng poison-reverse Undo ripng poison-reverse Information, refer to Frame Relay Configuration Commands on Lapb and X.25 Configuration Commands onRipng summary-address Poison reverse function takes effect Timers 1323 IPV6 Ripng Configuration Commands IPV6 Static Routing Configuration Commands Delete ipv6 static-routes allIpv6 route-static Delete ipv6 static-routes all Sysname system-view Sysname ipv6 route-static 112 24 Display multicast boundary Multicast Routing Forwarding Configuration CommandsRelated command multicast boundary Display multicast forwarding-table Major values of the flags field 1329MID Value Meaning Related command multicast minimum-ttl Display multicast minimum-ttl 1331 Related command display multicast forwarding-tableDisplay multicast routing-table Display multicast routing-table static Description on the fields of display multicast routing-table Display multicast rpf-info 1333 Ip rpf-route-static 1335 Related command display multicast routing-table static Mtracert 1337 Description on the fields of the mtracert commandMulticast boundary Related command display multicast boundary Multicast forwarding-table downstream-limit Multicast forwarding-table route-limit 1339 Multicast load-splitting Multicast longest-matchSyntax multicast longest-match Undo multicast longest-match View System view, VPN instance view Multicast routing-enable Related command display multicast minimum-ttlMulticast minimum-ttl 1341 Reset multicast forwarding-table # Enable IP multicast routing in VPN instance mvpn Reset multicast routing-table 1343 Sysname reset multicast routing-table Igmp Configuration Commands Display igmp group Description on the fields of the display igmp group command Display igmp interface 1347 Display igmp routing-table Related command igmp fast-leave,last-member-query-interval Fast-leave Igmp viewIgmp Syntax fast-leave group-policy acl-number Undo fast-leave Igmp enable Related command igmp enable, and multicast routing-enableonSyntax igmp enable Undo igmp enable Related command igmp Igmp fast-leave Igmp group-policyUndo igmp group-policy 1351 Igmp max-response-time By default, the last-member query interval is 1 secondIgmp last-member-query-interval Igmp require-router-alert 1353 Robust-count Igmp view , igmp timer query , igmp Igmp robust-countIgmp send-router-alert Igmp interface Igmp static-group Igmp timer other-querier-present Igmp timer query Related command version Igmp view Igmp versionLast-member-query-interval Undo igmp version Syntax require-router-alert Max-response-time Igmp viewRequire-router-alert Igmp view Reset igmp group Undo require-router-alertView Public instance Igmp view, VPN instance Igmp view 1359 Syntax robust-count robust-value Undo robust-count Related command display igmp groupRobust-count Igmp view Timer other-querier-present Igmp view Send-router-alert Igmp viewSyntax send-router-alert Undo send-router-alert 1361 Public instance Timer query Igmp viewSyntax timer query interval Undo timer query 1363 Related command igmp versionVersion Igmp view Igmp Configuration Commands Msdp Configuration Commands Cache-sa-enableDisplay msdp brief Characters Display msdp peer-status 1367 Display msdp sa-cache Related command cache-sa-enable 1369 Display msdp sa-count Encap-data-enable Syntax encap-data-enable Undo encap-data-enableImport-source View Public instance Msdp view, VPN instance Msdp view Msdp Related command peer sa-policyRelated command display multicast routing-tableon Originating-rp Peer connect-interfaceUndo originating-rp 1373 Related command static-rpf-peer Related command display msdp peer-statusPeer description Peer mesh-group Peer minimum-ttl Undo peer peer-addressmesh-groupUndo peer peer-addressminimum-ttl 1375 Peer request-sa-enable Peer sa-cache-maximum Import-source command Peer sa-policyFrom the Msdp peer Display msdp peer-status and import-source Reset msdp peer Peer sa-request-policy 1379 Reset msdp sa-cacheRelated command cache-sa-enableand display msdp sa-cache Undo shutdown peer-address Reset msdp statisticsShutdown Msdp View Related command display msdp peer-statusand ip prefix-list Example # Configure static RPF peers in the public instanceStatic-rpf-peer Undo static-rpf-peer peer-address Timer retry Syntax timer retry interval Undo timer retry PIM Configuration Commands Auto-rp enableRelated command static-rp PIM view Bsr-policy PIM view Bsr PIM view Undo c-bsr Bsr admin-scope Syntax c-bsr admin-scope Undo c-bsr admin-scopeBsr global 1385 Bsr group Undo c-bsr group group-address Bsr hash-length PIM view Bsr holdtime PIM viewSyntax c-bsr hash-length hash-length Undo c-bsr hash-length Syntax c-bsr holdtime interval Undo c-bsr holdtime Related command c-bsr PIM view and c-bsr interval PIM view Bsr interval PIM viewBsr priority PIM view Bsr PIM view and c-bsr holdtime PIM view Rp PIM view 1389 Related command c-bsr PIM view Rp advertisement-interval PIM viewRp advertisement-interval interval Undo c-rp advertisement-interval Related command c-rp PIM view and c-bsr interval PIM view Rp holdtime PIM viewCrp-policy PIM view Syntax c-rp holdtime interval Undo c-rp holdtime Related command c-bsr PIM view and c-rp PIM view Display pim bsr-info Display pim claimed-route 1393 Display pim control-message counters 1395 BSR Display pim interface Description on the fields of the display pim grafts commandDisplay pim grafts 1397 Display pim join-prune PIM DR Display pim neighbor 1399 Interface connecting the PIM neighbor Display pim routing-table 1401 Sysname display pim routing-table Vpn-instance public net Display pim rp-info 1403 Description on the fields of the display pim rp-info command Related command pim hello-optiondr-priority Hello-option dr-priority PIM viewHello-option holdtime PIM view 1405 Hello-option lan-delay PIM view This command is effective for both PIM-DM and PIM-SMRelated command pim hello-option holdtime Hello-option neighbor-tracking PIM view 1407 Related command pim hello-optionneighbor-trackingHello-option override-interval PIM view Syntax holdtime assert interval Undo holdtime assert Holdtime assert PIM viewHoldtime join-prune PIM view Related command jp-queue-size PIM view Jp-pkt-size PIM viewJp-queue-size PIM view Syntax jp-pkt-size packet-size Undo jp-pkt-size Undo pim vpn-instance vpn-instance-name Related command multicast routing-enableonPim Bsr PIM view , and multicast boundary on Pim bsr-boundaryPim dm Related command pim sm, ssm-policy PIM view Example # Enable PIM-DM on Ethernet 1/0Related command hello-optiondr-priority PIM view Pim hello-option dr-priority Pim hello-option lan-delay Related command hello-option holdtime PIM viewPim hello-option holdtime 1413 Pim hello-option neighbor-tracking Pim hello-option override-interval 1415 Pim holdtime assertPim holdtime join-prune View Interface view Parameter None Pim require-genidPim sm Pim timer graft-retry Related command pim dmExample # Enable PIM-SM on Ethernet 1/0 Example # Disable state refresh on Ethernet 1/0 Pim timer hello Pim timer join-pruneSyntax pim timer hello interval Undo pim timer hello Related command timer hello PIM view Pim triggered-hello-delay Related command timer join-prune PIM viewProbe-interval PIM view Syntax probe-interval interval Undo probe-interval Register-suppression-timeout PIM view Related command register-suppression-timeout PIM viewSyntax register-suppression-timeout interval Register-policy PIM view Undo register-suppression-timeout Register-whole-checksum PIM viewSyntax register-whole-checksum Undo register-whole-checksum 1421 Reset pim control-message counters Related command state-refresh-interval PIM viewSource-lifetime PIM view Syntax source-lifetime interval Undo source-lifetime Spt-switch-threshold PIM view Undo spt-switch-threshold group-policy acl-numberSource-policy PIM view Syntax source-policy acl-number Undo source-policy PIM Configuration Commands Ssm-policy PIM view State-refresh-interval PIM viewSyntax ssm-policy acl-number Undo ssm-policy 1425 Syntax state-refresh-ttl ttl-value Undo state-refresh-ttl State-refresh-rate-limit PIM viewState-refresh-ttl PIM view By default, the TTL value of state refresh messages is Static-rp PIM viewUndo static-rp rp-address 1427 Timer hello PIM view Timer join-prune PIM viewRelated command display pim rp-infoand auto-rp enable Related command pim timer hello Timer spt-switch PIM view Related command pim timer join-pruneSyntax timer spt-switch interval Undo timer spt-switch Related command spt-switch-threshold PIM view PIM Configuration Commands IPV6 Multicast Routing Forwarding Configuration Commands Related command multicast ipv6 boundaryDisplay multicast ipv6 boundary Display multicast ipv6 forwarding-table IPV6 Multicast Routing and Forwarding Configuration Commands 1433 Display multicast ipv6 minimum-hoplimitValues and meanings of the Flags field Related command multicast ipv6 minimum-hoplimit Display multicast ipv6 routing-table 1435 Related command display multicast ipv6 forwarding-tableDisplay multicast ipv6 rpf-info Multicast ipv6 boundary 1437 Related command display multicast ipv6 boundaryMulticast ipv6 forwarding-table downstream-limit Multicast ipv6 forwarding-table route-limit Multicast ipv6 load-splitting 1439 Multicast ipv6 longest-matchMulticast ipv6 minimum-hoplimit Multicast ipv6 routing-enable Related command display multicast ipv6 minimum-hoplimit 1441 Reset multicast ipv6 forwarding-tableReset multicast IPv6 routing-table Sysname reset multicast ipv6 routing-table ff03101 MLD Configuration Commands Display mld group Information of all interfaces running MLD Description on the fields of the display mld group commandDisplay mld interface Display mld routing-table 1445 Fast-leave MLD view Syntax fast-leave group-policy acl6-number Undo fast-leave Last-listener-query-interval Max-response-time MLD viewSyntax max-response-time interval Undo max-response-time 1447 Mld enable Syntax mld enable Undo mld enableMld Syntax mld Related command mld Example # Enable MLD on Ethernet 1/0Mld fast-leave Mld group-policy Mld last-listener-query-interval 1451 Mld max-response-timeMld require-router-alert Mld robust-count Syntax mld robust-count robust-value Undo mld robust-count Mld send-router-alert Mld static-groupMld send-router-alert Undo mld send-router-alert Mld timer other-querier-present Mld timer other-querier-present intervalUndo mld timer other-querier-present 125 x 2 + 10 / 2 = 255 seconds Mld timer query Syntax mld timer query interval Undo mld timer queryRelated command mld version Mld version Reset mld group Require-router-alert MLD viewRequire-router-alert Mld require-router-alert and send-router-alert MLD view Related command display mld group Robust-count MLD view# Clear all MLD forwarding entries on Ethernet 1/0 1457 Timer other-querier-present MLD view By default, the MLD querier robustness variable isSend-router-alert MLD view View MLD view Timer query interval Timer query MLD viewRelated command Version MLD view Example # Globally set the MLD version to MLDv2 IPV6 PIM Configuration Commands Bsr-policy IPv6 PIM viewBsr IPv6 PIM view Syntax bsr-policy acl6-number Undo bsr-policy Related command c-bsr IPv6 PIM view on Bsr hash-length IPv6 PIM view Example # Set the bootstrap timeout time to 150 seconds Bsr holdtime IPv6 PIM viewBsr interval IPv6 PIM view Syntax c-bsr interval interval Undo c-bsr interval Related command c-bsr IPv6 PIM view Bsr priority IPv6 PIM viewRp IPv6 PIM view Bsr IPv6 PIM view and c-bsr holdtime IPv6 PIM view 1465 Rp advertisement-interval IPv6 PIM viewView IPv6 PIM view Related command c-rp IPv6 PIM view Example # Set the global C-RP timeout time to 200 secondsRp holdtime IPv6 PIM view Example # Set the global C-RP-Adv interval to 30 seconds Related command c-bsr IPv6 PIM view and c-rp IPv6 PIM view Crp-policy IPv6 PIM viewDisplay pim ipv6 bsr-info Syntax crp-policy acl6-number Undo crp-policy Display pim ipv6 claimed-route Syntax display pim ipv6 claimed-route ipv6-source-address Display pim ipv6 control-message counters BSR Display pim ipv6 grafts Display pim ipv6 interfaceDisplay pim ipv6 grafts Unacknowledged graft messages Interface PIM version PIM mode Display pim ipv6 join-prune PIM-SM and IPv6 PIM-SSM respectivelyTo send on the specified interface Specified IPv6 PIM neighbor Display pim ipv6 neighbor Display pim ipv6 routing-table 1475 Related command display multicast ipv6 routing-tableon Example # View the content of the IPv6 PIM routing table 1477 Display pim ipv6 rp-infoSyntax display pim ipv6 rp-info ipv6-group-address Embedded-rp Syntax embedded-rp acl6-number Undo embedded-rp acl6-number Related command pim ipv6 hello-optiondr-priority Hello-option dr-priority IPv6 PIM viewHello-option holdtime IPv6 PIM view Example # Set the router priority for DR election to Hello-option lan-delay IPv6 PIM view Related command pim ipv6 hello-option holdtimeExample # Set the prune delay to 200 milliseconds globally Hello-option neighbor-tracking IPv6 PIM view Related command pim ipv6 hello-optionneighbor-tracking Example # Disable join suppression globallyHello-option override-interval IPv6 PIM view Holdtime assert IPv6 PIM view Holdtime join-prune IPv6 PIM view Related command jp-queue-size IPv6 PIM view Jp-pkt-size IPv6 PIM viewJp-queue-size IPv6 PIM view 1483 Related command multicast ipv6 routing-enableon Pim ipv6Pim ipv6 bsr-boundary Syntax pim ipv6 Undo pim ipv6 Related commands pim ipv6 sm, ssm-policy IPv6 PIM view Example # Enable IPv6 PIM-DM on Ethernet 1/0Pim ipv6 dm Syntax pim ipv6 dm Undo pim ipv6 dm Related command hello-optiondr-priority IPv6 PIM view Related command hello-option holdtime IPv6 PIM viewPim ipv6 hello-option dr-priority Pim ipv6 hello-option holdtime 1487 Pim ipv6 hello-option lan-delayPim ipv6 hello-option neighbor-tracking Related command hello-optionneighbor-tracking IPv6 PIM view Example # Disable join suppression on Ethernet 1/0Pim ipv6 hello-option override-interval Pim ipv6 holdtime assert Pim ipv6 holdtime join-prune Pim ipv6 require-genidSyntax pim ipv6 require-genid Undo pim ipv6 require-genid 1489 Pim ipv6 sm Pim ipv6 state-refresh-capablePim ipv6 sm Undo pim ipv6 sm 1491 Pim ipv6 timer graft-retryPim ipv6 timer hello Pim ipv6 timer join-prune Pim ipv6 triggered-hello-delayRelated command timer hello IPv6 PIM view Related command timer join-prune IPv6 PIM view Related command register-suppression-timeout IPv6 PIM view Probe-interval IPv6 PIM viewRegister-policy IPv6 PIM view Example # Set the probe time to 6 seconds Register-suppression-timeout IPv6 PIM view 1495 Reset pim ipv6 control-message countersRegister-whole-checksum IPv6 PIM view Related command state-refresh-interval IPv6 PIM view Source-lifetime IPv6 PIM viewSource-policy IPv6 PIM view Syntax source-policy acl6-number Undo source-policy 1497 Spt-switch-threshold IPv6 PIM viewUndo spt-switch-threshold group-policy acl6-number Ssm-policy IPv6 PIM view Syntax ssm-policy acl6-number Undo ssm-policy 1499 State-refresh-hoplimitState-refresh-interval IPv6 PIM view Example # Set the state refresh interval to 70 seconds State-refresh-rate-limit IPv6 PIM viewStatic-rp IPv6 PIM view Timer hello IPv6 PIM view Related command display pim ipv6 rp-infoUndo static-rp ipv6-rp-address 1501 Timer join-prune IPv6 PIM view Timer spt-switch IPv6 PIM viewRelated command pim ipv6 timer hello Related command pim ipv6 timer join-prune Related command spt-switch-threshold IPv6 PIM view 1503 IPV6 PIM Configuration Commands Display multicast-domain vpn-instance share-group Multicast VPN Configuration CommandsDisplay multicast-domain vpn-instance switch-group receive Count Display multicast-domain vpn-instance switch-group send 1507 Multicast-domain holddown-time Multicast-domain log switch-group-reuse Multicast-domain share-groupView VPN instance view 1509 Multicast-domain switch-delay 1511 Multicast-domain switch-group-poolUndo multicast-domain switch-group-pool Sysname system-view Sysname ip vpn-instance mvpn Display mpls fast-forwarding cache verbose Mpls Basics Configuration CommandsDisplay mpls fast-forwarding cache # Display all ILM entries Display mpls ilmSyntax display mpls ilm label include text 1515 Related command display mpls statistics interfaceDisplay mpls interface Display mpls label Display mpls label label-value1 to label-value2 all Mpls ldp system view , mpls ldp interface view Display mpls ldpDisplay mpls ldp all verbose begin exclude include LSR ID Description on the fields of the display mpls ldp commandDisplay mpls ldp cr-lsp Related command display mpls lsp Display mpls ldp interfaceAll Displays all information 1519 Example # Display information about all LDP interfaces # Display detailed information about all interfaces Display mpls ldp Isp All Displays information about all LSPs established by LDPDest-addr Destination address of the LSP Established by LDP Related command display mpls ldp Display mpls ldp peer 1523 Example # Display information about all peers# Display detailed information about all peers Display mpls ldp remote-peer Example # Display information about remote peer BJI Display mpls ldp session 1525 Example # Display information about sessions # Display detailed information about all sessionsLAM MD5 Display mpls ldp vpn-instance 1527 Display mpls lsp Example # Display information about VPN instance vpn1Incoming-interface Incoming interface of the LSPs Outgoing-interface Outgoing interface of the LSPs Exclude Excludes the specified FEC Include Includes the specified FECDest-addr Destination address Asbr Displays information about Asbr established LSPs Description on the fields of the display mpls lsp command Example # Display information about all LSPs# Display detailed information about all LSPs FEC Display mpls lsp statistics Display mpls nhlfeSyntax display mpls lsp statistics Syntax display mpls nhlfe token include text Display mpls route-state # Display all Nhlfe entries Display mpls static-lsp 1533 # Display detailed information about static LSPs Display mpls statistics interfaceExample # Display brief information about static LSPs 1535 Related command statistics intervalExample # Display Mpls statistics for all interfaces Display mpls statistics lsp Syntax display mpls statistics lsp index all name lsp-name Example # Display Mpls statistics for all LSPs 1537 Du-readvertise timer Syntax du-readvertise timer value Undo du-readvertise timerDu-readvertise Are both Graceful-restart Mpls LDP view Graceful-restart mpls ldpView Mpls LDP view Syntax graceful-restart mpls ldp Graceful-restart timer neighbor-liveness Graceful-restart timer reconnectRelated commands graceful-restart Mpls LDP view Syntax graceful-restart timer reconnect timer 1541 Graceful-restart timer recoveryUndo graceful-restart timer reconnect Related command loop-detect,path-vectors Hops-countLabel advertise Syntax hops-count hop-number Undo hops-count Label-distribution Undo label advertiseLabel-distribution independent ordered Undo label-distribution Undo label-retention Label-retentionLabel-retention conservative liberal Related command hops-count,path-vectors Use the undo lsp-trigger command to restore the defaultLoop-detect Lsp-trigger # Configure the LDP LSR ID of LDP instance named vpn1 Lsr-idSyntax lsr-idlsr-id Undo lsr-id Md5-password MplsSyntax mpls Undo mpls Related command mpls lsr-id # Enable Mpls for interface Ethernet 1/0Mpls ldp system view View System view/interface view # Enable LDP for VPN instance vpn1 Mpls ldp interface viewSyntax mpls ldp Undo mpls ldp 1549 Undo mpls ldp advertisement Mpls ldp advertisementMpls ldp advertisement dod du Mpls ldp timer hello-hold Related command remote-ipMpls ldp remote-peer Example # Create a remote peer entity named BJI Mpls ldp timer keepalive-hold Mpls ldp transport-address Mpls lsr-idView Interface view/MPLS LDP remote peer view Syntax mpls lsr-id lsr-id Undo mpls lsr-id Mtu-signalling Related command display mpls interfaceSyntax mtu-signalling Undo mtu-signalling Example # Set the LSR ID to Related command loop-detect,hops-count Path-vectorsPing lsp Syntax path-vectors pv-number Undo path-vectors Remote-ip Syntax remote-ip ip-address Undo remote-ip Reset mpls fast-forwarding cache Reset mpls ldpRelated command mpls ldp remote-peer Reset mpls fast-forwarding cache Syntax reset mpls statistics lsp index all name lsp-name Reset mpls statistics interfaceReset mpls statistics lsp Snmp-agent trap enable mpls Related command display mpls statistics lspStatic-lsp egress Lsp-name Name for the LSP, a string of 1 to 15 characters Static-lsp ingress Undo static-lsp ingress lsp-name 1561 Static-lsp transitUndo static-lsp transit lsp-name Related command static-lsp egress, static-lsp ingress Statistics intervalTracert lsp Syntax tracert lsp -a source-ip-exp Ttl expiration pop command Ttl expirationTtl expiration pop Undo ttl expiration pop Ttl propagate Mpls TE Configuration Commands Add hop Delete hop Display explicit-pathSyntax delete hop ip-address Syntax display explicit-path pathname 1567 Display isis traffic-eng advertisements# Display the latest TE information advertised by IS-IS TE Intf Addr 1569 Display isis traffic-eng linkVerbose Displays details Display isis traffic-eng network Vpn-instance vpn-instance-name Specifies a VPN instance. Display isis traffic-eng statistics 1571 Related command te-set-subtlv Display isis traffic-eng sub-tlvs Display mpls rsvp-te Label switched Router ID, Display mpls rsvp-te established Begin include exclude regular-expressionAbout RSVP-TE globally or for an interface # Display RSVP-TE information for interface Ethernet 1/0 Spaces Display mpls rsvp-te peerFilters output by regular expression Display mpls rsvp-te psb-content 1577 Erhopstrict Display mpls rsvp-te request RSVP-TE requests on the specified or all interfaces1579 X.X Display mpls rsvp-te reservation LSP ID Display mpls rsvp-te rsb-content1581 Tunnel Dest Display mpls rsvp-te sender 1583 Display mpls rsvp-te statistics Global Display global RSVP-TE informationInterface is specified RSVP-TE is displayed # Display the RSVP-TE statistics of interface Serial 1/0 1585 Display mpls static-cr-lsp Ip-address prefix-length arguments 1587 Display mpls te cspf tedb# Display detailed information about all static CR-LSPs IGP # Display the Tedb information of IGP area # Display all Tedb information1589 Mpls LSR ID IGP # Display the Tedb information of all nodes # Display Tedb information for a specified interface address Display mpls te link-administration admission-control Links of all interfaces if no interface is specified 1593 Display mpls te link-administration bandwidth-allocationDescription on fields of the command Display mpls te tunnel Egress ingress remote transit name name incoming-interface LSP-ID # Display detailed information about Mpls TE tunnels1595 # Display the paths that all Mpls TE tunnels traverse Display mpls te tunnel pathLsr-id Ingress LSR ID, in dotted decimal notation Display mpls te tunnel statistics Display mpls te tunnel-interfaceSyntax display mpls te tunnel statistics Syntax display mpls te tunnel-interface CR-LSP Display ospf mpls-te 1599 Area ID TE enabled Ospf area ID LSA Type 1601 Display ospf traffic-adjustmentSyntax display ospf process-id traffic-adjustment # Display statistics about tunnels Display tunnel-infoSyntax display tunnel-info tunnel-id all statistics Enable traffic-adjustment Enable traffic-adjustment advertise# Enable IGP shortcut when the IGP protocol is IS-IS View Ospf view/IS-IS view Explicit-path List hop 1605 Modify hopView Explicit path view Mpls rsvp-te authentication Mpls rsvp-te authentication cipher plain auth-keyUndo mpls rsvp-te authentication Mpls rsvp-te Mpls rsvp-te blockade-multiplier 1607 Related command mpls rsvp-te timer refresh Mpls rsvp-te graceful-restartMpls rsvp-te hello Syntax mpls rsvp-te hello Undo mpls rsvp-te hello 1609 # Enable Rsvp hello extension on interface Ethernet 1/0Mpls rsvp-te hello-lost Related command mpls rsvp-te timer hello Mpls rsvp-te keep-multiplierMpls rsvp-te reliability Example # Set the keep multiplier to five Mpls rsvp-te resvconfirm Mpls rsvp-te srefresh Mpls rsvp-te timer graceful-restart recovery Mpls rsvp-te timer graceful-restart restart Mpls rsvp-te timer hello Mpls rsvp-te timer refreshRelated command mpls rsvp-te hello, mpls rsvp-tehello-lost Example # Set the hello interval to five seconds Undo mpls rsvp-te timer retransmission Mpls rsvp-te timer retransmissionRelated command mpls rsvp-tekeep-multiplier # Enable Mpls TE on interface Ethernet 1/0 Mpls teSyntax mpls te Undo mpls te Related command mpls te link administrative group Mpls te affinity propertyMpls te auto-bandwidth Undo mpls te auto-bandwidth Mpls te backup Related command mpls te timer auto-bandwidthMpls te backup hot-standby ordinary Undo mpls te backup Example # Enable hot backup on tunnel Mpls te backup bandwidthWith backup enabled, the record route Mpls te bandwidth Mpls te bandwidth change thresholdsMpls te bandwidth bc0 bc1 bandwidth Undo mpls te bandwidth View Tunnel interface view Mpls te commitSyntax mpls te commit Mpls te cspf timer failed-link Related command mpls te cspfExample # Set the failed link timer to 50 seconds Mpls te cspf Syntax mpls te fast-reroute Undo mpls te fast-reroute Mpls te fast-rerouteMpls te fast-reroute bypass-tunnel Mpls te igp advertise Description Example# Set the hold time to 10000 milliseconds 1623 Mpls te igp metric Mpls te igp shortcutMpls te igp shortcut isis ospf Undo mpls te igp shortcut Mpls te link administrative group Related command mpls te affinity propertyMpls te loop-detection Syntax mpls te loop-detection Undo mpls te loop-detection Mpls te max-link-bandwidth Mpls te max-reservable-bandwidth Related command mpls te path metric-type Mpls te metricUndo mpls te max-reservable-bandwidth Syntax mpls te metric value Undo mpls te metric Related command mpls te metric Mpls te path explicit-pathMpls te path metric-type Example In Mpls view Mpls te priority Mpls te record-routeUndo mpls te priority Syntax mpls te record-route label Undo mpls te record-route Mpls te reoptimization Mpls te reoptimization user viewMpls te reoptimization tunnel interface view Mpls te resv-style Mpls te retry Related command mpls te timer retry Example # Set the maximum number of tunnel setup retries toExample # Enable route pinning Mpls te route-pinning Mpls te signal-protocol Mpls te signal-protocol crldp rsvp-te staticMpls te tie-breaking Mpls te tie-breaking least-fill most-fill random Related command mpls te auto-bandwidth Mpls te timer auto-bandwidthBy default, automatic bandwidth adjustment is disabled Mpls te timer fast-reroute Mpls te timer retrySyntax mpls te timer retry second Undo mpls te timer retry 1635 Related command mpls te retry Examples # Configure the tunnel ID asMpls te tunnel-id Mpls te vpn-binding Mpls-te enable Syntax mpls-te enable Undo mpls-teRelated command opaque-capability Next hop Related command delete hop Opaque-capability Reset mpls rsvp-te statistics Reset mpls te auto-bandwidth adjustment timersSyntax reset mpls te auto-bandwidth adjustment timers Static-cr-lsp egress Static-cr-lsp ingress Undo static-cr-lsp transit tunnel-name Static-cr-lsp transitCR-LSP on the ingress or a transit node Use the undo te-set-subtlvcommand to restore the default # Configure sub-TLVs for IS-IS processBw-constraint Sets the bandwidth constraint sub-TLV Value Sub-TLV in the range 19 to If no level is specified, IS-IS TE applies to Level-1-2 Cost-style on Mpls TE Configuration Commands Mpls L2VPN Configuration Ccc interface in-label out-label Ccc interface out-interface Undo ce ce-name Connection # Create a CE named ce2 for a VPNView Mpls L2VPN CE view 1647 Tunnel select-seq load-balance-number on Related command route-distinguisher Mpls L2VPN viewDisplay bgp l2vpn 1649 CE ID Verbose Peer Local 1651 Pref Preference Display ccc Syntax display ccc ccc-name ccc-nametype local remote# Display information about all local CCC connections # Display information about all CCC connections Display l2vpn ccc-interface vc-type Down Configured on the router Configured on the CE interfaceDisplay mpls l2vc 1655 VC ID VC ID Display mpls l2vpn Vpn-name local-ce remote-ce # Display information about local CEs of L2VPN vpn1 Description on the fields of the display mpls l2vpn command# Display information about L2VPN vpn1 1659 Display mpls l2vpn connection# Display information about remote CEs of L2VPN vpn1 Status Status of the connection Peer-id Description on the fields of mpls l2vpn connection summary Example # Display Mpls L2VPN forwarding information Display mpls l2vpn forwarding-infoDisplay mpls static-l2vc 1663 L2vpn-familySyntax l2vpn-family Undo l2vpn-family Related command tunnel select-seqload-balance-numberonMpls l2vc Mpls l2vpn Mpls l2vpn vpn-nameExample # Create a Martini Mpls L2VPN connection Syntax mpls l2vpn Undo mpls l2vpn Undo mpls static-l2vc Mpls static-l2vc destination# Create Kompella VPN named vpn2 and enter Mpls L2VPN view Reset bgp l2vpn Mtu Mpls L2VPN viewSyntax mtu mtu Example # Set the MTU for Kompella connections to Re-create the VPN using the new RD Takes effect only when it is configured with an RDRoute-distinguisher Mpls L2VPN view Route-distinguisher route-distinguisher 1669 Vpn-target Mpls L2VPN viewExample # Associate VPN vpn1 with VPN targets Mpls L2VPN Configuration Commands Apply access-vpn vpn-instance Default local-preference BGP-VPNv4 subaddress family viewSyntax default local-preference value View Policy routing view Default med BGP-VPNv4 subaddress family view 1673 Description VPN instance viewDisplay bgp vpnv4 all routing-table Example # Display all BGP VPNv4 routing information 1675 Display bgp vpnv4 groupAll Specifies all VPNv4 peers Display bgp vpnv4 network Display bgp vpnv4 paths Display bgp vpnv4 all vpn-instance vpn-instance-name pathsBe displayed # Display all BGP VPNv4 AS path information VPNv4 peers Display bgp vpnv4 peerVerbose Displays detailed information 1679 # Display all BGP VPNv4 peer information # Display detailed information about BGP VPNv4 peer 1681 Display bgp vpnv4 route-distinguisher routing-table 1683 Related command route-distinguisher VPN instance viewExample # Display the BGP VPNv4 routing information of RD Fields of the above output 1685 Display bgp vpnv4 routing-table labelAll Specifies all VPNv4 peers Display bgp vpnv4 vpn-instance routing-table 1687 Display fib statistics vpn-instance Display fib vpn-instanceDisplay fib statistics vpn-instance Display fib vpn-instance vpn-instance-name include string 1689 Display ip vpn-instance# Display detailed information about a VPN instance Related command sham-link Display ospf sham-linkSyntax display ospf process-id sham-link area area-id Example # Display information about all Ospf sham links Display tunnel-policy # Display information about Ospf sham links in areaDisplay tunnel-policy all policy-name tunnel-policy-name Tunneling policy or all tunneling policies # Display tunneling policy aaa Example # Configure the Ospf domain IDDomain-id 1693 Export route-policyFilter-policy export BGP-VPNv4 subaddress family view Filter-policy import BGP-VPNv4 subaddress family view 1695 Import route-policyIp binding vpn-instance Ip vpn-instance Ipv4-familyView BGP view Vpnv4 Enters BGP-VPNv4 subaddress family view Peer advertise-community BGP-VPNv4 subaddress family view 1697 Peer allow-as-loop Peer as-path-acl BGP-VPNv4 subaddress family view Peer default-route-advertise vpn-instance 1699 Peer filter-policy BGP-VPNv4 subaddress family view Peer enableRelated command peer upe Peer group 1701 Peer ip-prefix BGP-VPNv4 subaddress family view Peer label-route-capability BGP view/BGP VPN instance view Peer next-hop-invariable BGP-VPNv4 subaddress family view 1703 Peer next-hop-local Peer public-as-only BGP-VPNv4 subaddress family view Peer reflect-client 1705 Peer route-policy BGP-VPNv4 subaddress family view Peer upe Command applies to inter-provider VPN option B schemes Policy vpn-targetSyntax policy vpn-target Undo policy vpn-target 1707 Reflect between-clients Reflector culster-id Refresh bgp vpn-instance 1709 Reset bgp vpn-instance Refresh bgp vpnv4 1711 Reset bgp vpn-instance dampeningReset bgp vpn-instance flap-info Syntax route-distinguisher route-distinguisher Reset bgp vpnv4Route-distinguisher VPN instance view Then re-create the VPN instance and re-configure a new RD Route-tagInstance Syntax route-tag tag-value Undo route-tag Import-route Ospf view on Example # Configure the route tag for Ospf process 100 asRouting-table limit Rr-filter Sham-linkUndo rr-filter View Ospf area view Mpls L3VPN Configuration Commands Related command tunnel select-seqload-balance-number Tnl-policy VPN instance viewTunnel-policy Undo tnl-policy Undo tunnel select-seq Load-balance-number command can be usedTunnel select-seq load-balance-number Vpn-instance-capability simple Vpn-target VPN instance viewView Ospf multi-instance view 1719 Mpls L3VPN Configuration Commands VAM Server Configuration Commands Authentication-algorithmAuthentication-method Vam server vpn , authentication-method Vam server vpn , authentication-algorithm Display vam server address-map Display vam server statistic Syntax display vam server statistic all vpn vpn-nameDescription on the fields of display vam server address-map 1723 Example # Display statistics of the VAM server # Display statistics of VPN domain 1 on the VAM server Related command vam server vpn Encryption-algorithmHub private-ip Undo hub private-ip private-ip-address Related command vam server vpn, keepalive retry Keepalive interval Related command vam server vpn, keepalive interval Keepalive retryPre-shared-key VPN domain view Syntax keepalive retry retry-times Undo keepalive retry Server enable Syntax server enable Undo server enableRelated command vam server vpn, vam server enable Example # Enable the VAM server function of VPN domain Vam server ip-address Vam server enableRelated command Vam server vpn, server enable Example Vam server vpn Syntax vam server vpn vpn-name Undo vam server vpn vpn-name VAM Client Configuration Commands Client enableRelated command vam client name, and vam client enable 100 Example # Display the status information of VAM client abc Pre-shared-key VAM client view Pre-shared-key cipher simple key-stringVAM client view Cipher Specifies a pre-shared key in cipher text No pre-shared key is configured by default Related command vam client nameResend interval Syntax resend interval time-interval Undo resend interval 1735 Server primary ip-addressServer secondary ip-address Vam client enable By default, no local username or password is configuredExample # Set the local username and password both to user User Vam client name and client enable By default, no VAM client is configuredVam client name An interface Example # Specify the VAM client abc to belong to VPN VpnUndo vpn Ipsec Profile Configuration Commands Related command ipsec profile system view101 Display ipsec profile Inbound ESP setting Ipsec profile system view 1741 Ipsec Profile Configuration Commands Dvpn Tunnel Configuration Commands 102Display dvpn session Associated with the VAM client Dvpn session dumb-time Dumb Dvpn session idle-time Ipsec profile tunnel interface viewUndo ipsec profile ipsec-profile-name&1-6 1745 Keepalive Undo keepalive Syntax tunnel-protocol dvpn udp Undo tunnel-protocol Related command Interface tunnel on ExampleTunnel-protocol dvpn udp Related command interface tunnel on Example # Configure the Dvpn tunnel modeVam client Syntax vam client client-name Undo vam client 103 GRE Configuration CommandsRelated command interface tunneland source Example # Display information about interface Tunnel0 Down 1751 Gre checksum Syntax gre checksum Undo gre checksum Related command interface tunnel Gre keyUndo gre key 1753 Syntax interface tunnel number Undo interface tunnel number 1755 Tunnel-protocol gre Syntax tunnel-protocol gre ipv6 Undo tunnel-protocol L2TP Configuration Commands 104Allow l2tp Undo allow Related command l2tp-group Related command Display l2tp tunnel ExampleDisplay l2tp session Sessions 1759 Display l2tp tunnelSyntax display l2tp tunnel L2tp enable L2tp sendaccm enableRelated command allow l2tp Syntax l2tp enable Undo l2tp enable L2tpmoreexam enable L2tp enableUse the undo l2tp-group command to remove an L2TP group L2tp-group Related command allow l2tp and start l2tp Related command Mandatory-lcp ExampleMandatory-chap Mandatory-lcp Reset l2tp tunnel Related command mandatory-chapUndo mandatory-lcp View L2TP group view Tunnel authentication Related command display l2tp tunnelSyntax tunnel authentication Start l2tp Undo tunnel authentication Tunnel avp-hiddenSyntax tunnel avp-hidden Undo tunnel avp-hidden 1765 Tunnel flow-control Tunnel name Tunnel password Tunnel timer hello L2TP Configuration Commands Traffic Policing TP Configuration Commands Description on the fields of the display qos car commandDisplay qos car interface Filed Description Description on the fields of the display qos carl command Display qos carlQos car Display qos carl carl-index 1771 Qos carl Undo qos carl carl-index Examples # Configure Carl rule 1 with packet precedence 1773 Traffic Policing TP Configuration Commands Traffic Shaping Configuration Commands Description on the fields of the display qos gts command106 Display qos gts interface Qos gts Undo qos gts any acl acl-number queue queue-number Related commands acl on 1777 Traffic Shaping Configuration Commands Line Rate Configuration Commands Description on the fields of the display qos lr command107 Display qos lr interface Undo qos lr inbound outbound Qos lr interface viewQos lr layer 2 interface view or port group view 1781 Layer 2 module interface view, port group viewInterfaces is 4 or 9, this argument is not supported Line Rate Configuration Commands Display traffic classifier Defining Class Commands108 If-match Undo if-match not match-criteriaClass view Match-criteria Class match rules. The values are as follow 1785 Value Description Rtp start-portEnd-port Qos-local-id Define Mpls EXP precedence matching rule 1787 Related commands traffic classifier# Define a class to match ACL # Define a class to match the ACL named flow # Define a class to match IPV6 ACL# Define a class to match the IPv6 ACL named flow # Define matching rule for all packets Undo traffic classifier tcl-name Traffic classifierTraffic classifier tcl-name operator and or By default, the relation is operator Examples # Define a class named as class1 Defining Traffic Behavior Commands 109Car Undo car Display traffic behavior Qos policy , traffic behavior , classifier behavior Filter GtsFilter deny permit Undo filter Redirect Undo gtsUndo redirect View Traffic behavior view 1795 Remark atm-clpSyntax remark atm-clp atm-clp-value Undo remark atm-clp Remark dot1p Remark dscpSyntax remark dot1p 8021p Undo remark dot1p Syntax remark dscp dscp-value Undo remark dscp 1797 Remark fr-deSyntax remark fr-de fr-de-value Undo remark fr-de Remark ip-precedence Remark mpls-expExamples # Remark the DE bit in FR packets to Syntax remark mpls-exp exp-value Undo remark mpls-exp 1799 Remark qos-local-idTraffic behavior Examples # Define a traffic behavior named behavior1 Defining Policy Commands Related commands qos policy110 Classifier behavior Description on the fields of the display qos policy command System-defined Policy pre-defined by the systemUser-defined Policy pre-defined by the user Tcl-name Class name in the policy Display qos policy interface 1803 Qos apply policy interface view EXP Qos apply policy layer 2 interface view or port group view 1805 Qos policy Syntax qos policy policy-name Undo qos policy policy-name 1807 Defining Policy Commands Fifo Queuing Configuration Commands 111Qos fifo queue-length 1809 Fifo Queuing Configuration Commands PQ Configuration Commands Related commands qos pq112 Display qos pq interface Related commands qos pq, qos pq pql Qos pqExamples # Display PQLs Syntax qos pq pql pql-index Undo qos pq Qos pql default-queue Qos pql inbound-interfaceExamples # Apply the priority list 12 to the Ethernet 1/0 1813 By default, no classification rule is configured Qos pql protocolDescription on values of queue-key and key-value Queue-key Key-value Description Qos pql queue 1815 PQ Configuration Commands CQ Configuration Commands Related commands qos cq113 Display qos cq interface Default values will not be displayed Qos cqExamples # Display information about a CQL Syntax qos cq cql cql-index Undo qos cq Qos cql default-queue Examples # Assign default queue 2 to CQLQos cql inbound-interface 1819 Qos cql protocol Descriptions of values of queue-key and key-value Qos cql queue 1821 Examples # Specify byte-count of queue 2 in the CQL 5 to Qos cql queue servingUndo qos cql cql-indexqueue queue-numberserving WFQ Configuration Commands Related commands qos wfq114 Display qos wfq interface Display interface, display qos wfq interface Qos wfqUndo qos wfq CBQ Configuration Commands 115Display qos cbq interface Qos max-bandwidth Queue af Queue ef 1827 Queue wfq Queue-length WredSyntax wred dscp ip-precedence Undo wred 1829 Wred dscp Undo wred dscp dscp-value Wred ip-precedence 1831 Wred weighting-constant RTP Priority Queue Configuration Commands Description on the fields of the display qos rtpq command116 Display qos rtpq interface Qos rtpq Qos rtpq Related commands qos reserved-bandwidth 1835 RTP Priority Queue Configuration Commands QOS Token Configuration Commands 117Qos qmtoken Qos qmtoken token-number QOS Token Configuration Commands Priority Mapping Table Configuration Commands Related commands qos map-tabledot1p-Ip118 Display qos map-table Related commands display qos map-table Parameters in the default mapping tableQos map-table dot1p-Ip Import 1841 Priority Mapping Table Configuration Commands Port Priority Configuration Commands 119Qos priority Undo qos priority Port Priority Configuration Commands Port Priority Trust Mode Configuration Commands 120Display qos trust interface Qos trust Port Priority Trust Mode Configuration Commands Wred Configuration Commands 121Display qos wred interface 1847 Qos wred enable Qos wred dscp ip-precedence enableUndo qos wred enable Dscp Uses the Dscp value for calculating drop probability By default, the dropping method of a queue is tail drop Related commands qos wfq, display qos wred interfaceQos wred dscp 1849 Undo qos wred ip-precedence ip-precedence Qos wred weighting-constantDiscard-probability discard-prob Length, in the range 1 to 16. It defaults to Wred with the qos wred enable command on itQos wred enable, display qos wred interface Calculate the average length of Wred queues Wred Configuration Commands Wred Table Configuration Commands 122Display qos wred table Syntax display qos wred table table-name Qos wred apply Qos wfq , qos wred enable , display qos wred interfaceQos wred queue table 1855 Related commands qos wred queue table in system viewQueue Wred Table Configuration Commands Mpls QOS Configuration Commands 123If-match mpls-exp Qos cql protocol mpls exp Related commands qos cql protocol Qos pql protocol mpls exp 1859 Related commands qos pql protocolExamples # Set EXP value of remarked Mpls packet to Mpls QOS Configuration Commands DAR Configuration Commands 124Dar max-session-count Dar protocol Protocols of pre-defined ports Protocol name Protocol type Pre-defined port number 1863 # Restore the default name of the user-defined01 protocol Dar protocol-renameDar protocol-statistic Undo dar protocol-rename user-defined-name Display dar information Undo dar protocol-statisticSyntax display dar information 1865 Display dar protocol Display dar protocol all protocol-name 1867 Display dar protocol-rename Display dar protocol-rename Display dar protocol-statistic If-match protocol If-match protocol http Undo if-match not protocol rtp payload-type audio video Reset dar protocol-statisticIf-match protocol rtp Information, i.e. to restore the statistics to Reset dar sessionAll Deletes all statistics information # Deletes all statistics information DAR Configuration Commands FR QOS Configuration Commands 125Apply policy outbound # Define a traffic behavior named behavior Related commands ebs, cir allow, cir CbsCir Undo cir Related commands Cir allowCbs, ebs, cir allow Cir allow inbound outbound committed-information-rate Related commands cbs, ebs, cir Related commands fr congestion-thresholdCongestion-threshold Undo cq 1879 Related commands wfq, pq, fr pvc-pqDisplay fr class-map Related commands fragment Display fr fragment-info # Display FR fragment information of a certain interfaces 1881 Display fr switch-table Fr switch 1883 # Display PVC PQ information on FR interface Serial2/0 Display qos pvc-pq interfacePVC PQ on FR interface Fifo queue-length Related commands Cbs, cir allow, cir ExamplesEbs Related commands fr class Related commands fr-classFr class Fr congestion-threshold 1887 Related commands congestion-thresholdFr de del Fr del inbound-interface Related commands fr del inbound-interface,fr del protocolRelated commands fr de del, fr del protocol Related commands fr de del, fr del inbound-interface Fr del protocolProtocol ip IP 1889 Undo fr pvc-pq Related commands pvc-pqFr pvc-pq Related commands fr class, fr-class,fr dlci Fr traffic-policingFr traffic-shaping Syntax fr traffic-policing Undo fr traffic-policing Examples # Enable Frts on the serial interface Serial 1/0 FragmentFr-class Undo fragment fragment-size Related commands fr class, fr dlci Related commands cq, wfq, fr pvc-pqPvc-pq Undo pq Rtpq Undo pvc-pqFr pvc-pq Number, in the range 2000 to Undo traffic-shaping adaptation becn interface-congestion Related commands fr traffic-shaping,cir allow, and cirTraffic-shaping adaptation Related commands cq, pq, fr pvc-pq WfqUndo wfq Examples # Apply WFQ to the FR class test1 802.1X Configuration Commands Example # Display 802.1x configuration information126 Display dot1x Descriptions on the fields of the display dot1x command Dot1x Dot1x interface interface-listUndo dot1x interface interface-list Dot1x Dot1x authentication-method Related command display dot1x# Enable 802.1x globally Syntax dot1x authentication-method chap eap pap Undo dot1x authentication-method Dot1x guest-vlan Dot1x guest-vlan vlan-id Undo dot1x guest-vlan Undo dot1x handshake Dot1x handshakeDot1x handshake Dot1x max-user user-number Undo dot1x max-user Dot1x max-userUndo dot1x max-user interface interface-list Dot1x port-control By default, the multicast trigger function is enabledDot1x multicast-trigger Dot1x port-method Dot1x port-method macbased portbased Undo dot1x port-method 1907 Dot1x quiet-periodSyntax dot1x quiet-period Undo dot1x quiet-period Related command display dot1x, dot1x timer Dot1x retryDot1x supp-proxy-check Undo dot1x retry 1909 Dot1x timer Reset dot1x statistics Example # Set the server timeout timer to 150 secondsReset dot1x statistics interface interface-list 1911 Example # Clear 802.1x statistics on port Ethernet 1/1 AAA Configuration Commands Access-limitAccounting default 127 AAA Configuration Commands Accounting lan-access Accounting loginRelated command accounting default, radius scheme 1915 Syntax accounting optional Undo accounting optional Undo accounting loginAccounting optional Accounting portal 1917 Accounting ppp Related command domain, radius scheme Undo attribute access-limit idle-cut ip location mac vlanAccounting voip Attribute Authentication default Related command display local-userLocal Performs local authentication Example # Set the IP address of local user user1 to Authentication lan-access Undo authentication lan-accessLocal Performs local authentication None Does not perform any authentication Authentication login Related command authentication default, radius scheme Authentication portal 1923 Radius-scheme radius-scheme-name local Authentication pppUndo authentication ppp 1925 Authentication voipAuthorization command Authorization default Related command authorization default, hwtacacs scheme Authorization lan-access 1927 Authorization login Related command authorization default, radius scheme Authorization portal 1929 Authorization ppp Authorization voipUndo authorization ppp Authorization default , hwtacacs scheme , radius scheme Cut connection Domain , radius scheme Display connection Related command cut connection Example Description on the fields of the display connection commandDisplay domain # Display information about all AAA user connections Related command access-limit,domain, state Description on the fields of the display domain command Related command local-user Display local-user Domain # Display information about all local usersUndo domain isp-name Description on the fields of display local-user Domain default Related command access-limit,state, display domainDomain default disable enable isp-name State , display domain Idle-cut Ip poolDomain Domain aabbcc.net Related command remote address on LevelSyntax level level Undo level Related command display local-user,service-type Local-userExample # Set the level of user user1 to Example # Add a local user named user1 Related command display local-user , password Local-user password-display-modePassword Self-service-url Service-type Service-type ftp Service-type pppRelated command service-type ppp and service-type ftp Syntax service-type ftp Undo service-type ftp State State active block Related command domain Work-directory# Place the current user user1 to the state of blocked Syntax work-directory directory-name Undo work-directory 1947 AAA Configuration Commands Radius Configuration Commands Accounting-on enable128 Radius scheme Related command radius scheme, accounting-on enable Accounting-on enable intervalAccounting-on enable send Data-flow-format Radius scheme view GigabyteMega-packet, or giga-packet Packets to be sent to a Radius server Related command display radius scheme Related command radius schemeExample # Display the configurations of all Radius schemes Display radius scheme Display radius statistics Display radius statisticsExample # Display statistics about Radius packets 1953 State statistictotal=1024 State statistics 1955 Dead Display stop-accounting-buffer Which is a string of 1 to 32 charactersTime range, or user name On August 31 Display radius scheme Key Radius scheme viewNas-ip Radius scheme view Undo primary accounting Related command radius nas-ipPrimary accounting Radius scheme view Primary authentication Radius scheme view 1959 Syntax radius client enable Undo radius client Example # Enable the listening port of the Radius clientRadius client Radius nas-ip Related command nas-ip Radius scheme view Radius schemeUndo radius nas-ip Undo radius scheme radius-scheme-name Radius trap Reset radius statistics Reset stop-accounting-bufferSyntax reset radius statistics Example # Clear Radius statistics Retry Undo retry Retry realtime-accounting 1965 Undo secondary accounting Retry stop-accounting Radius scheme viewSecondary accounting Radius scheme view Secondary authentication Radius scheme view 1967 Security-policy-server Server-typeSyntax server-type extended standard Undo server-type View Radius scheme view Use the state command to set the status of a Radius server Primary Sets the status of the primary Radius serverSecondary Sets the status of the secondary Radius server Accounting Sets the status of the Radius accounting server Stop-accounting-buffer enable Radius scheme view Timer quiet Radius scheme view Timer realtime-accounting Radius scheme viewSyntax timer quiet minutes Undo timer quiet 1971 Number of users Real-time accounting interval minute Timer response-timeout Radius scheme viewRelated command retry realtime-accounting,radius scheme User-name-format with-domain without-domain Related command radius scheme, retryUser-name-format Radius scheme view Radius Configuration Commands Hwtacacs Configuration Commands Related command display hwtacacs129 Data-flow-format Hwtacacs scheme view Related command hwtacacs scheme Description on the fields of the display hwtacacs command Address or a loopback address Hwtacacs nas-ipScheme view , retry stop-accounting Hwtacacs scheme view Undo hwtacacs scheme hwtacacs-scheme-name Related command nas-ip Hwtacacs scheme viewHwtacacs scheme Key accounting authentication authorization string Undo key accounting authentication authorization stringKey Hwtacacs scheme view Nas-ip Hwtacacs scheme view Related command hwtacacs nas-ip Primary accounting Hwtacacs scheme view 1981 Primary authentication Hwtacacs scheme viewExample # Set the primary authentication server Primary authorization Reset hwtacacs statisticsUndo primary authorization Accounting Clears Hwtacacs accounting statistics Retry stop-accounting Hwtacacs scheme view Secondary accounting Hwtacacs scheme view Secondary authentication Hwtacacs scheme viewSyntax secondary authentication ip-address port-number 1985 Secondary authorizationExample # Configure the secondary authentication server View Hwtacacs scheme view Stop-accounting-buffer enable Hwtacacs scheme viewExample # Configure the secondary authorization server 1987 Timer quiet Hwtacacs scheme viewTimer realtime-accounting Hwtacacs scheme view Timer response-timeout Hwtacacs scheme view User-name-format Hwtacacs scheme view Hwtacacs scheme Hwtacacs Configuration Commands Packet Filter Firewall Configuration Commands Switch running a routing protocolDisplay firewall ethernet-frame-filter All Displays all the firewall statistics information Firewall default Syntax firewall default permit denyDisplay firewall-statistics Fragments-inspect Firewall enable Firewall enableUndo firewall enable Firewall ethernet-frame-filter Example # Enable fragments inspection Firewall fragments-inspect Firewall fragments-inspect high low number default Firewall fragments-inspect high lowFirewall ipv6 fragments-inspect Undo firewall fragments-inspect high low Related command firewall fragments-inspect Firewall packet-filter Reset firewall ethernet-frame-filter Firewall packet-filter ipv6Outbound Undo firewall packet-filter ipv6 inbound outbound # Clear the firewall statistic information of Ethernet 1/0 Reset firewall-statisticsExample # Clear all the firewall statistic information Aspf Configuration Commands 131Aging-time Aging-time syn fin tcp udp seconds Aspf-policy # Set the TCP idle timeout period to 3000 seconds# Set the UDP idle timeout period to 110 seconds 2001 Display aspf allSyntax display aspf all Display aspf interface Syntax display aspf interface Display aspf policy Display aspf sessionSyntax display aspf policy aspf-policy-number Display aspf session verbose Display port-mapping Related command port-mapping Firewall aspfExample # Display all the information about port mapping 2005 Log enable Syntax log enable Undo log enableExample # Enable the session logging function of the Aspf Port-mapping Reset aspf session Related command display port-mappingSyntax reset aspf session Example # Map port 3456 to the FTP protocol Aspf Configuration Commands MAC Authentication Configuration Commands Display mac-authenticationSyntax display mac-authentication interface interface-list DFIC-9FSW and MSR 20 Series Products Mac-authentication MAC Addr Mac-authentication domain 2011 Mac-authentication timer Related command display mac-authentication Mac-authentication user-name-format Reset mac-authentication statistics NAT Configuration Commands Connection-limit default actionConnection-limit default amount 133 Connection-limit enable Connection-limit enableUndo connection-limit enable Connection-limit policy Display connection-limit policy Example # Create a connection-limit policy numberedSyntax display connection-limit policy policy-numberall 2017 Display connection-limit statistics Display nat address-group Display nat address-groupView Any view Parameter None Information Display nat aging-time Display nat allDisplay nat aging-time Different NAT sessions Description on some fields of the display nat all command 2021 Display nat connection-limit Destination address Display nat log Mask-length The length of net mask, in the range 1 toSyntax display nat log 2023 # View the NAT log configuration Description on the fields of the display nat log commandDisplay nat outbound Display nat outbound Syntax display nat server Display nat serverDisplay nat session Syntax display nat statistics Display nat statisticsExample # Display the active NAT sessions Display userlog export Limit acl View Connection-limit policy view Limit modeSyntax limit mode amount Undo limit mode Nat address-group Nat aging-timeUndo nat address-group group-number Tcp-syn udp seconds Nat alg Nat connection-limit-policy 2031 Nat log enable Nat log flow-active Nat log flow-begin Nat outboundNat log flow-begin Undo nat log flow-begin NAT Configuration Commands # Configure the address pool Nat outbound staticNat server Syntax nat outbound static Undo nat outbound static NAT Configuration Commands 2037 # Remove the WWW server using the following commands Nat static 2039 Reset nat sessionSyntax reset nat session Reset userlog export Reset userlog nat logbufferRelated command display userlog export Userlog nat export host Related command userlog nat export source-ip Related command userlog nat export hostUserlog nat export source-ip 2041 Syntax userlog nat syslog Undo userlog nat syslog Userlog nat export versionUserlog nat syslog PKI Configuration Commands 134 Ca identifier Syntax ca identifier name Undo ca identifier Pki entity Certificate request entityCertificate request from Certificate request mode Simple password * manualUndo certificate request mode Certificate request polling Related command display pki certificate Certificate request urlUndo certificate request polling count interval 2047 Common-name CountrySyntax common-name name Undo common-name Undo country Crl update-period Crl check disable enableCrl update-period hours Undo crl update-period Undo crl url Crl urlDisplay pki certificate Example # Display the local certificate 2051 Display pki certificate access-control-policy Display pki certificate attribute-group Related command pki retrieval-crl domain and pki domain Display pki crl domainSyntax display pki crl domain domain-name Example # Display the locally saved CRLs Fqdn Ip PKI entity viewUndo fqdn Undo ip Ldap-server LocalityUndo ldap-server Undo locality Syntax organization org-name Undo organization OrganizationOrganizational-unit 2057 Pki certificate access-control-policyPki certificate attribute-group Syntax pki domain domain-nameundo pki domain domain-name Pki delete-certificatePki domain Pki entity Pki import-certificatePki entity entity-name Undo pki entity entity-name Related command pki domain Pki request-certificate domain Related command Pki domain Example Pki retrieval-certificatePki retrieval-crl domain Pki retrieval-certificate ca local domain domain-name Pki validate-certificate Root-certificate fingerprintPki validate-certificate ca local domain domain-name Root-certificate fingerprint md5 sha1 string 2063 Rule access control policy viewSyntax rule id deny permit group-name Undo rule id all Undo state Portal Configuration Commands Portal authentication135 Display portal acl Description on the fields of the display portal acl command Display portal connection statisticsAll Displays portal connection statistics on all interfaces Statistics on the specified interface 2067 Syntax display portal free-rule rule-number Msgauthenack Msgauthorack Msgloginack MsglogoutackDisplay portal free-rule 2069 Related command portal free-ruleDisplay portal interface Related command portal server Display portal serverSyntax display portal server server-name URL Display portal server statistics All Displays portal server statistics on all interfaces2071 Reqchallenge Display portal tcp-cheat statistics Syntax display portal tcp-cheat statistics Display portal user Specified interface enabling portalSpecified interface or all interfaces enabling portal 2073 Portal auth-network Undo portal auth-network network-addressall Related command display portal user Portal delete-userPortal free-rule Undo portal free-rule rule-numberall Related command display portal free-rule Portal resource-name Related command display portal server Portal serverUndo portal server server-name key port url 2077 Reset portal connection statistics Portal server method Reset portal tcp-cheat statistics Reset portal server statisticsReset portal tcp-cheat statistics Portal Configuration Commands Rsh RSH Configuration Commands136 INSTALL.LOG Common Configuration Commands Description on the fields of the display time-range commandDisplay time-range Time-range Common Configuration Commands 2085 Common Configuration Commands IPV4 ACL Configuration Commands 138Acl 2087 Acl copy # Create IPv4 ACL 2002, giving the ACL a name of flow# Delete the IPv4 ACL with the number # Delete the IPv4 ACL named flow 2089 Acl nameSyntax acl name acl-name # Define the description of ACL Description for IPv4# Define the description of IPv4 ACL Description on the fields of the display acl command Display aclSyntax display acl acl-numberall name acl-name 2091 Reset acl counter Syntax reset acl counter acl-number all name acl-nameRule in basic IPv4 ACL view # Clear statistics about IPv4 ACL flow 2093 Rule in advanced IPv4 ACL view TCP/UDP-specific parameters for advanced IPv4 ACL rules Parameter Function Description Icmp-type Icmp message Type Code 2097 Rule in Ethernet frame header ACL viewUndo rule rule-id Rule in user-defined ACL view View User-defined ACL view Support to this command varies by device Rule comment for IPv4# Create a user-defined ACL rule Syntax rule rule-idcomment text Undo rule rule-idcomment Step for IPv4 # Create a rule in ACL 3000 and define the rule description# Create a rule in ACL 4000 and define the rule description # Create a rule in ACL 5000 and define the rule description Example # Set the rule numbering step to 2 for ACL 2101 IPV4 ACL Configuration Commands IPV6 ACL Configuration Commands 139Acl ipv6 2103 Acl ipv6 copy # Create IPv6 ACL 2002, giving the ACL a name of flow# Delete the IPv6 ACL with the number # Delete the IPv6 ACL named flow 2105 Acl ipv6 nameSyntax acl ipv6 name acl6-name Description for IPv6 Display acl ipv6# Create a description for IPv6 ACL Syntax display acl ipv6 acl6-numberall name acl6-name Reset acl ipv6 counter All All basic and advanced IPv6 ACLs2000 to 2999 for basic IPv6 ACLs 3000 to 3999 for advanced IPv6 ACLs Undo rule rule-id fragment logging source time-range Rule in basic IPv6 ACL view# Clear the statistics about the IPv6 ACL named flow Rule in advanced IPv6 ACL view 2109 Time-range time-name Parameter Function Description Source sourceDestination dest Available ICMPv6 messages TCP/UDP-specific match criteria for advanced IPv6 ACL rulesICMPv6-specific match criteria for advanced IPv6 ACL rules Rule in simple IPv6 ACL view View Simple IPv6 ACL view Parameters for simple IPv6 ACL rules ICMPv6 messages definable in simple IPv4 ACL rules TCP/UDP-specific parameters for simple IPv6 ACL rulesICMPv6-specific parameters for simple IPv6 ACL rules 2115 Support for this command varies by deviceRule comment for IPv6 Step for IPv6 Example # Set the rule numbering step to 2 for IPv6 ACL # Set the rule numbering step to 2 for IPv6 ACL 2117 IPV6 ACL Configuration Commands Ipsec Configuration Commands Ah authentication-algorithmCryptoswitch fabric enable 140 Display encrypt-card fast-switch Syntax display encrypt-card fast-switch Ipsec policy system view Display ipsec policyDisplay ipsec policy brief name policy-name seq-number # Display detailed information about all IPSec policies Display ipsec policy-template IPSec policy template group10000 Template group Related command ipsec proposal Display ipsec proposalDisplay ipsec sa Syntax display ipsec proposal proposal-name Reset ipsec sa, ipsec sa global-duration Description on the fields of the display ipsec sa command Related command reset ipsec session Display ipsec sessionSyntax display ipsec session tunnel-id integer Example # Display information about all IPSec sessions Related command reset ipsec statistics Display ipsec statisticsSyntax display ipsec statistics Example # Display IPSec packet statistics 2129 Display ipsec tunnelSyntax display ipsec tunnel Encrypt-card fast-switch Encapsulation-mode Esp authentication-algorithm Related command display encrypt-cardfast-switchEsp encryption-algorithm Syntax esp encryption-algorithm 3des aes key-length des Syntax ike-peer peer-name Undo ike-peer peer-name Ike-peer IPSec policy view/IPSec policy template viewUndo esp encryption-algorithm 2133 Related command ipsec policy-templateIpsec binding policy Ipsec cpu-backup Syntax ipsec cpu-backup enable Undo ipsec cpu-backup enable Ipsec policy interface view 2135 Ipsec policy system view Syntax ipsec policy policy-nameseq-number isakmp manual Ipsec policy isakmp template Ipsec policy-templateUndo ipsec policy-template template-name seq-number 2137 Ipsec proposal Related command display ipsec policy-templateRelated command display ipsec proposal Related command sa duration, display ipsec sa duration Ipsec sa global-durationIpsec session idle-time Example # Create an IPSec proposal named newprop1 Pfs Undo ipsec session idle-timePfs dh-group1 dh-group2 dh-group5 dh-group14 Undo pfs Example # Enable and configure PFS for IPSec policy policy1 Related command ipsec proposal, ipsec policy system viewProposal Undo proposal proposal-name Syntax reset encrypt-card fast-switch Reset encrypt-card fast-switchReset ipsec sa Syntax reset ipsec session tunnel-id integer Reset ipsec sessionRelated command display ipsec sa Reset ipsec statistics Sa authentication-hexRelated command display ipsec session Syntax reset ipsec statistics 2145 Sa durationView IPSec policy view/IPSec policy template view Sa encryption-hex Sa spi 2147 Sa string-key Example # Configure IPSec policy policy1 to reference ACL Security aclSyntax security acl acl-number Undo security acl 2149 Example # Configure IPSec proposal prop1 to use AH TransformTunnel local Syntax transform ah ah-esp esp Undo transform Tunnel remote 2151 Example # Set the remote address of the IPSec tunnel to Ike proposal, display ike proposal IKE Configuration Commands141 Related command ike proposal, display ike proposal Certificate domainDh group1 group2 group5 group14 Undo dh Related command ike dpd Display ike dpdExample # Specify 768-bit Diffie-Hellman for IKE proposal Syntax display ike dpd dpd-name Related command ike peer system view Display ike peerDisplay ike proposal Syntax display ike peer peer-name Example # Display the settings of IKE proposals Related command ike proposal, ike peer system viewDisplay ike sa 2157 # Display detailed information about the current IKE SAs 2159 Encryption-algorithm 3des-cbc aes-cbc key-length des-cbc DpdUndo dpd Id-type Related command Id-type ExampleExchange-mode Ike dpd Ike local-nameExample # Use the ID type of name in IKE negotiation Syntax ike dpd dpd-name Undo ike dpd dpd-name Ike next-payload check disabled Related command remote-name,id-typenameExample # Configure the local gateway name as app 2163 Related command display ike proposal Ike peer system viewIke proposal Syntax ike peer peer-name Undo ike peer peer-name Ike sa keepalive-timer interval Ike sa keepalive-timer timeoutRelated command ike sa keepalive-timer timeout Example # Set the keepalive interval to 200 seconds Ike sa nat-keepalive-timer interval Related command ike sa keepalive-timer intervalExample # Set the keepalive timeout to 20 seconds Interval-time Local Local-address Nat traversal Syntax nat traversal Undo nat traversalPeer multi-subnet single-subnet Undo peer Related command authentication-algorithmon Pre-shared-keyRemote-address Syntax pre-shared-key key Undo pre-shared-key Reset ike sa Related command id-typeip, local-addressRelated command id-type,ike local-name Remote-name Related command display ike sa Example # Clear the IPSec tunnel toSyntax sa duration seconds Undo sa duration 2171 Syntax time-out time-out Undo time-out Related command ike proposal and display ike proposalTime-out SSH2.0 Configuration Commands 142Display public-key local Public-key local create Example Display public-key peer Display public-key peer brief name publickey-nameBrief Displays brief information about all public keys Specified or all public keys Related command sftp client source Display sftp client source# Display brief information about all public keys Syntax display sftp client source Related command ssh client source Display ssh client sourceDisplay ssh server Syntax display ssh client source Display ssh server-info # Display the session information of the SSH serverSyntax display ssh server-info 2177 Related command ssh user Display ssh user-informationSyntax display ssh user-information username Example # Display information about all SSH users Related command Public-key peer Example Peer-public-key endPublic-key-code begin Peer-public-key end Public-key-code end Public-key local createPublic-key-code end Public-key peer, public-key-code begin Public-key local destroy Public-key local destroy, display public-key local Example# Create local RSA key pair # Create local DSA key pair Related command public-key local create Public-key local export rsaPublic-key local export rsa openssh ssh1 ssh2 filename Public-key local create , public-key local destroy Public-key local export dsa # Display the RSA local public key in OpenSSH formatPublic-key local export dsa openssh ssh2 filename # Export the DSA local public key in OpenSSH format Related command public-key-code begin, public-key-code end Public-key peer# Display the DSA local public key in OpenSSH format Syntax public-key peer keyname Undo public-key peer keyname 2185 Public-key peer import sshkeySftp Ipv6 ipv6-address Specifies a source IPv6 address Sftp client ipv6 sourceUndo sftp client ipv6 source Sftp ipv6 Related command Display sftp client source ExampleSftp client source Sysname sftp ipv6 Input Username Sftp server enable Sftp server idle-timeoutSyntax sftp server enable Undo sftp server enable Related command display ssh server Ssh client authentication server Ssh client first-time enable To access the SSH server Ssh client ipv6 sourceSsh client source Undo ssh client ipv6 source Ssh server authentication-retries Related command display ssh client source Ssh server authentication-timeout Ssh server compatible-ssh1x enableBy default, the authentication timeout period is 60 seconds Example # Enable the SSH server to work with SSH1.x clients Ssh server rekey-interval Ssh server enableSyntax ssh server enable Undo ssh server enable 2195 Ssh userUndo ssh user username Related command display ssh user-information Ssh2 Ssh2 ipv6 2197 SSH2.0 Configuration Commands 2199 SSH2.0 Configuration Commands Sftp Configuration Commands 143Bye Syntax bye Cdup DeleteDir Syntax cdup Exit GetSyntax exit 2203 Help 2205 MkdirPut Pwd QuitSyntax pwd Syntax quit Remove RenameRmdir 2207 Sftp-client rmdir temp1 Directory successfully removed SSL Configuration Commands 144Ciphersuite View SSL server policy view Client-verify enable Syntax client-verify enable Undo client-verify enableExample # Set the SSL connection close mode to wait Close-mode wait Display ssl client-policy Display ssl server-policySyntax display ssl client-policy policy-nameall Syntax display ssl server-policy policy-nameall Handshake timeout Syntax handshake timeout time Undo handshake timeoutPki-domain Syntax pki-domain domain-name Prefer-cipher Undo pki-domainUndo prefer-cipher 2213 Session cachesize size timeout time Undo session cachesize timeoutSession Rsaaes128cbcsha 2215 Ssl client-policySsl server-policy Use the undo version command to restore the default Version ssl3.0 tls1.0SSL client policy view Ssl3.0 Specifies SSL Syntax display standby flow Backup Center Configuration CommandsDisplay standby flow Main and backup interfaces Display standby stateDisplay standby state Following tables describe the meanings of each state Backup states of the backup interface Backup flagsStandby bandwidth Syntax standby bandwidth size Undo standby bandwidth Related command standby interface Standby interface Related commands standby track Standby thresholdUndo standby threshold 2221 Undo standby timer delay Standby timer delayRelated command standby interface and standby bandwidth Standby timer flow-check Standby trackUndo standby track 2223 Standby interface, track on IPV4-BASED Vrrp Configuration Commands Display vrrp Description on the fields of the display vrrp command Vrrp vrid track interface commandVrrp vrid track command Display vrrp statistics Example # Display the statistics about all standby groups 2227 Reset vrrp statistics Vrrp vrid authentication-mode255 Device are cleared 2229 Vrrp methodSyntax vrrp method real-mac virtual-mac Undo vrrp method Vrrp ping-enable Vrrp ping-enableUndo vrrp ping-enable Addresses of standby groups Default mode is immediate preemption without delay Vrrp un-check ttlVrrp vrid preempt-mode Syntax vrrp un-check ttl Undo vrrp un-check ttl Vrrp vrid priority 2233 Vrrp vrid timer advertiseVrrp vrid track Vrrp vrid track interface Vrrp vrid virtual-ip 2235 # Add virtual IP address 10.10.10.11 to standby group Vrrp Configuration Commands For IPV6 147Display vrrp ipv6 IPv6 Vrrp ipv6 vrid track command Display vrrp ipv6 statistics 2239 Syntax vrrp ipv6 method real-mac virtual-mac Reset vrrp ipv6 statisticsVrrp ipv6 method Vrrp ipv6 ping-enable Vrrp ipv6 ping-enableUndo vrrp ipv6 ping-enable Undo vrrp ipv6 method Vrrp ipv6 vrid authentication-mode Vrrp ipv6 vrid preempt-mode 2243 Vrrp ipv6 vrid priorityUndo vrrp ipv6 vrid virtual-router-idpriority Vrrp ipv6 vrid timer advertise Undo vrrp ipv6 vrid virtual-router-idtimer advertise Vrrp ipv6 vrid track 2245 # Configure the virtual IPv6 address of standby group 1 as Vrrp ipv6 vrid virtual-ip Device Management Commands 148 Bootrom Buzzer enableSyntax buzzer enable Undo buzzer enable Part Display boot-loader This command is applicable on MSR 50 series routers onlyDisplay boot-loader slot slot-number Related command Boot-loader Display cpu-usage Display cpu-usage task number offset verbose from-device Description on fields of the display boot-loader command Display deviceSyntax display device cf-card usb slot slot-numberverbose 2251 Cf-card Displays information of a compact Flash CF Usb Displays information of a universal serial bus USBVaries with devices Such as card, CF, USB, VCPM, VPM and DSP Cpld Description on fields on the display device command2253 Display device manuinfo Display device manuinfo slot slot-numberInformation about the device Display # Display the temperature information of cards Display environmentExample # Display manufacturing information of a device Display environment Display fan Display licenseDisplay fan fan-id Display license Display power Syntax display power power-idDisplay memory Syntax display memory Display reboot-type Display schedule rebootDisplay reboot-type slot slot-number Display schedule reboot Reboot Only users at management level can execute this commandReboot slot slot-number License register Reset unused porttag Use the remove command to remove a cardSyntax reset unused porttag Remove slot slot-number 2261 Schedule reboot atSyntax schedule reboot at hhmm date Undo schedule reboot Schedule reboot delay Syntax schedule reboot delay hhmm mm Undo schedule reboot Temperature-alarm enable 2263 Temperature-limit Undo temperature-limit slot-number Syntax data-fill string Undo data-fill NQA Client Configuration CommandsData-fill Syntax data-size size Undo data-size Data-sizeDescription any NQA test type view Destination ip Destination portSyntax destination ip ip-address Undo destination ip Syntax destination port port-number Undo destination port Syntax display nqa result history admin-nameoperation-tag Display nqaResult Displays the results of the last test History Displays the history records of a test Description on the fields of the display nqa result command 2269 # Display the history records of tests Field Description Index History record number Filename FrequencySyntax filename filename Undo filename Syntax frequency interval Undo frequency History-records Syntax history-records number Undo history-records Http-version Next-hopHttp-version Undo http-version Nqa agent enable Syntax nqa agent enable Undo nqa agent enableRelated command nqa server enable Nqa Example # Enable the NQA client Nqa agent max-concurrentNqa schedule 2275 Operation FTP test type view Operation Http test type viewOperation get put Undo operation Password FTP test type view Syntax password password Undo passwordOperation interface Undo operation interface Probe count Syntax probe count times Undo probe count 2279 Probe packet-intervalProbe packet-number Syntax probe timeout timeout Undo probe timeout Probe packet-timeoutProbe timeout Reaction 2281 Undo reaction trap probe-failure test-complete test-failure Reaction trapRoute-option bypass-route Related command source ip Source interfaceUndo source interface 2283 Related command source interface Source ipSource port Syntax source ip ip-address Undo source ip Tos TtlSyntax tos value Syntax ttl value Type Url Username FTP test type viewSyntax url url Undo url Vpn-instance ICMP-echo test type view Syntax vpn-instance instance Undo vpn-instance NQA Server Configuration Commands 150Display nqa server status Syntax display nqa server status Nqa server enable Syntax nqa server enable Undo nqa server enableRelated command nqa server tcp-connect,nqa server udp-echo Example # Enable the NQA server 2291 Nqa server udp-echoUndo nqa server udp-echo ip-addressport-number Sysname nqa server udp-echo 169.254.10.2 Syntax display ip netstream cache Netstream Configuration CommandsDisplay ip netstream cache Ip netstream statistics command Display ip netstream exportDisplay ip netstream export Exported NetStream UDP packets Enable Syntax enableUndo enable Related command ip netstream aggregation Ip netstream aggregation Source-prefix Ip netstream export host Ip netstream export sourceExample # Enter NetStream AS aggregation view 2297 Ip netstream export version Ip netstream timeout active Related command ip netstream timeout inactiveIp netstream max-entry 2299 Ip netstream timeout inactive Reset ip netstream statisticsRelated command ip netstream timeout active Reset ip netstream statistics NTP Configuration Commands Display ntp-service sessionsSyntax display ntp-service sessions verbose 152 Example # View the NTP service status information Display ntp-service statusDisplay ntp-service status 2303 Display ntp-service traceSyntax display ntp-service trace Ntp-service access Undo ntp-service access peer query server synchronizationProtection. a more secure method is identity authentication Sure you have already created and configured this ACL Ntp-service authentication enable Ntp-service authentication-keyidBy default, NTP authentication is disabled # Enable NTP authentication Ntp-service broadcast-client Ntp-service broadcast-server Ntp-service in-interface disable 2307 Ntp-service max-dynamic-sessions Ntp-service multicast-client Ntp-service multicast-server Ntp-service refclock-masterUndo ntp-service multicast-server ip-address 2309 Ntp-service reliable authentication-keyid Ntp-service source-interfaceUndo ntp-service source-interface Used as a reference clock Ntp-service unicast-peer Public network Ntp-service unicast-serverVpn-instance-name in your command No NTP server is designated for the device by default Designated for the deviceInterface and the NTP server coexist in this VPN 2313 NTP Configuration Commands Rmon Configuration Commands Display rmon alarmSyntax display rmon alarm entry-number Related command rmon alarm Related command rmon event Example # Display the configuration of Rmon event tableDescription on the fields of the display rmon event command Display rmon event Display rmon eventlog Display rmon historySyntax display rmon eventlog entry-number 2317 Related command rmon history Display rmon prialarm Syntax display rmon prialarm entry-numberRelated command rmon prialarm Current-configuration and display this commands you cannot Display rmon statistics Related command rmon statisticsWith the display current-configuration and display 2321 Rmon alarmUndo rmon alarm entry-number Rising alarm and falling alarm are alternate Table with the rmon event commandYou can create up to 60 alarm entries Rmon event You can create up to 100 alarm entries Rmon historyUndo rmon history entry number Display rmon history 2325 Rmon prialarmUndo rmon prialarm entry-number # Remove private alarm entry Configurations the same and the creation failsYou can create up to 50 pri-alarm entries Rmon statistics 2327 Rmon Configuration Commands Snmp Configuration Commands Display snmp-agent local-switch fabricid154 Display snmp-agent community Descriptions on the fields of display snmp-agent community Display snmp-agent groupSyntax display snmp-agent group group-name 2331 Display snmp-agent mib-viewName of the specified MIB view Display snmp-agent statistics Syntax display snmp-agent statistics Display snmp-agent sys-info Display snmp-agent sys-info contact location versionVersion Displays the version of the current Snmp agent 2333 Syntax display snmp-agent trap-list Related command snmp-agent trap enableDisplay snmp-agent trap-list Enable snmp trap updown Syntax enable snmp trap updown Undo enable snmp trap updownDisplay snmp-agent usm-user # Display SNMPv3 information for the user aa Undo snmp-agent Snmp-agentSnmp-agent Snmp-agent community Undo snmp-agent community community name Undo snmp-agent group v3 group-name authentication privacy Related command snmp-agentmib-view,snmp-agentusm-userSnmp-agent group Undo snmp-agent group v1 v2c group-name Snmp-agent usm-user Snmp-agent local-switch fabricidSnmp-agent log Snmp-agent mib-view Undo snmp-agent mib-view view-name Related command snmp-agent group Snmp-agent packet max-sizeSnmp-agent sys-info 2341 Related command Display snmp-agentsys-info Snmp-agent target-host 2343 Snmp-agent trap enable Linkup warmstart * system voice vrrp authfailure newmaster Snmp-agent trap if-mib link extended Snmp-agent trap if-mib link extendedUndo snmp-agent trap if-mib link extended NMS, the device may not be able to resolute the messages Snmp-agent trap life Snmp-agent trap queue-size Example # Configure the size of the Trap queue to Snmp-agent trap sourceSnmp-agent usm-user Undo snmp-agent trap source Parameter v1 SNMPv1 2349 Snmp Configuration Commands File System Configuration Commands Copy Syntax delete /unreserved file-url Syntax dir /all file-url 2353 ExecuteSyntax execute filename File prompt FixdiskFile prompt alert quiet Syntax fixdisk device Format Syntax format device# create a subdirectory named mytest under test 2355 More MountSyntax more file-url Syntax mount device Related command Example Umount Move# Mount a CF card on a centralized device 2357 Reset recycle-bin Syntax reset recycle-bin /forceExample # Move the file cf/test/sample.txt to cf/sample.txt Example # Rename the file sample.txt as sample.bak 2359 UmountSyntax umount device Related command mount UndeleteExample # Unmount a CF card on a device Syntax undelete file-url Configuration File Management Commands Backup startup-configurationDisplay saved-configuration Syntax display saved-configuration by-linenum Configuration File Management Commands Reset saved-configuration Related command startup saved-configurationReset saved-configuration backup main Display startup Restore startup-configuration Related command save, display saved-configuration 2365 Syntax save file-name safely backup mainSave Startup saved-configuration Related command display startup 2367 Configuration File Management Commands FTP Server Configuration Commands Related command ftp timeout and ftp update157 Display ftp-server Ftp server enable Syntax ftp server enable Undo ftp serverDescription on the fields of the display ftp-user command Free ftp user Ftp timeout Ftp updateSyntax ftp timeout minute Undo ftp timeout Syntax ftp update fast normal Undo ftp update Sysname system-view Sysname ftp update normal FTP Client Configuration Commands 158Ascii Binary Syntax cd pathname Close DebuggingSyntax close Syntax debugging Undo debugging Description on the fields of the debugging command View FTP client view Parameter remotefile File name # View the content of aa.txt DisconnectSyntax disconnect 2377 Display ftp client configuration Syntax display ftp client configurationRelated command ftp client source Ftp Undo ftp client source Ftp client sourceFtp client source Related command display ftp client configuration Ftp ipv6 2381 Lcd Syntax lcd 2383 # View the content of file aa.txtOpen Related command close Open ipv6 Passive Syntax passiveUndo passive 2385 Parameter protocol-command FTP command Remotehelp 2387 # Display the help information for the user commandDescription on the fields of the remotehelp command Nlst SiteSyst Stat Verbose Syntax verboseUndo verbose 2389 FTP Client Configuration Commands Tftp Client Configuration Commands Display tftp client configuration159 Tftp-server acl Tftp # Associate IPv6 ACL 2001 with Tftp application in Ipv6 Related command tftp client source IP address configured on the deviceTftp client source On the source interface, the transmission fails Related command display tftp client configuration Tftp ipv6 2395 Tftp Client Configuration Commands Ping System Maintaining Commands160 Ping ipv6 2399 Tracert Range 1 to 65535, defaulting to 65535, in milliseconds. The default value is 5000 msTracert ipv6 With IPv6 address System Maintaining Commands System Debugging Commands 161Undo debugging all module-name option View User view Parameter all All debugging functions Debugging Related command display debuggingDisplay debugging Basic Configuration Commands 162Clock datetime Clock summer-time one-off Basic Configuration Commands Clock summer-time repeating 2407 Clock timezone Command-privilege Command-privilege level level view view commandUndo command-privilege view view command Display clock Configure-user count Description Related commandDisplay configure-user Display clipboard Display configure-user Syntax display configure-userDisplay clock Syntax display clock Exclude text Display current-configurationRelated command configure-user count Special characters in regular expression 2413 Display diagnostic-information # Display the configuration beginning with userDisplay diagnostic-information Version, display device, display current-configuration Display history-command Syntax display history-commandDisplay hotkey Display hotkey Display this Syntax display this by-linenum 2417 Display versionSyntax display version Header Header incoming legal login motd shell textUndo header incoming legal login motd shell Hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu command Ctrl+G corresponds to display current-configurationHotkey Undo hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu # Display the configuration of hotkeys Related command quit ReturnSuper Syntax return Super password Related command super passwordSuper password level user-level simple cipher password Undo super password level user-level # Display the password for switching user-level SysnameSyntax sysname sysname Undo sysname 2423 Related command quit, return System-viewSyntax system-view Example # Enter system view from the current user view Information Center Configuration Commands Description on the fields of the display channel commandDisplay channel Example # Display information for channel Display info-center Syntax display info-center Description on the fields of the display info-center command 2427 Display logbuffer Represents information level, in the range 0 toSeverity description Meanings of characters in text 2429 Descriptions on the fields of the display logbuffer commandRest is omitted here Display logbuffer summary Display logfile bufferDisplay logbuffer summary level severity Syntax display logfile buffer Support for the command varies with devices Example # Display the contents of the log file bufferDisplay logfile summary Syntax display logfile summary Display trapbuffer Info-center channel nameDisplay trapbuffer size buffersize Trap buffer, in the range 1 to 1,024 Info-center console channel 2433 Info-center enable Syntax info-center enable Undo info-center enableInfo-center logbuffer Undo info-center logbuffer channel size Info-center logfile enable Example # Enable the log file featureInfo-center logfile frequency 2435 Info-center logfile size-quota Info-center logfile switch-directorySyntax info-center logfile switch-directory dir-name Info-center loghost # Set the directory to save the log file to cf/testUndo info-center loghost host-ip 2437 Info-center loghost source Undo info-center loghost source Info-center monitor channel Info-center snmp channelUndo info-center snmp channel 2439 Info-center source Default output rules for different output directions Output Modules Enabled Direction Allowed Disabled Severity2441 NMS Info-center synchronous Info-center timestamp Undo info-center timestamp loghost Info-center timestamp loghostInfo-center timestamp loghost date no-year-date none Info-center trapbuffer Logfile saveUndo info-center trapbuffer channel size Syntax logfile save Terminal debugging Reset logbufferReset trapbuffer Syntax terminal logging Undo terminal logging Terminal loggingUndo terminal debugging Terminal monitor Terminal trapping Sysname terminal trapping Current terminal trapping is on User Interface Configuration Commands Acl ipv6 acl-number inbound outboundUndo acl ipv6 acl-number inbound outbound Acl acl-number inbound Activation-key Syntax activation-key character Undo activation-key Auto-execute command 2451 None Performs no authentication Password Performs local password authenticationAAA, refer to AAA Configuration Commands on Users log onto the device using the current user interface Undo databits DatabitsDatabits 5 6 7 Display user-interface Display history-commandHistory-commandmax-size # Display summary about all user interfaces 2455 Description on the fields of the display users command Display usersDisplay users all All Displays information about users on all user interfaces Syntax escape-key default character Undo escape-key Escape-keyExample # Define a as the escape key 2457 None 2459 Free user-interfaceSyntax free user-interface num1 aux console tty vty num2 View User interface view History-command max-size# Terminate the connection with user interface VTY Password next time you enter the system LockLock Operating under the active user interface Only, and cannot be applied to the Console port Example # Set the answering mode to auto-answer Example # Set the timeout interval to 50 secondsParity Syntax parity even mark none odd space Undo parity Example # Enable the VTYs 0 through 4 to support SSH only Protocol inboundExample # Perform odd parity check on the AUX interface Syntax protocol inbound all pad ssh telnet Redirect enable Redirect enableUndo redirect enable Redirect disconnect Related command telnet, display tcp statistics on Redirect listen-portRedirect refuse-negotiation Redirect listen-port port-number Undo redirect return-deal from-telnet Redirect return-deal from-telnetRedirect return-deal from-telnet Redirect timeout Redirect return-deal from-terminal Screen-length SendSyntax screen-length screen-length Undo screen-length Syntax send all num1 aux console tty vty num2 Undo set authentication password Set authentication passwordSet authentication password cipher simple password Related command authentication-mode ShellSyntax shell Undo shell Speed in user interface view Stopbits Terminal type User privilege level Syntax user privilege level level Undo user privilege level # Enter the user interface view of VTY 0 to # Enable user 1 to access level 3 commandsUser-interface User Interface Configuration Commands MAC Address Table Management Configuration Commands Display mac-addressEthernet interfaces Display mac-address blackhole vlan vlan-id count Display mac-address aging-time Display mac-address mac-learningSyntax display mac-address aging-time Port Index Mac-address Ethernet interface view 2479 Related command display mac-address Mac-address system viewBlackhole MAC address entries are dropped Specified Vlan ID, in the range 1 to Mac-address mac-learning disable 2481 Mac-address max-mac-count Ethernet interface view Related command display mac-addressmac-learningExample # Disable global MAC address learning Undo mac-address timer aging Mac-address timerMac-address timer aging seconds no-aging MAC Address Table Management Configuration Commands Apply poe-profile POE Configuration Commands166 Module, and slot of the power sourcing equipment PSE Description on fields of the display poe device commandDisplay poe device Display poe interface 2487 Description on fields of the display poe interface command # Display the state of all PoE interfaces Display poe interface power 2489 Syntax display poe power-usage Display poe power-usage# Display the power information of all PoE interfaces 2491 Display poe pseSyntax display poe pse pse-id Description on fields of the display poe pse command Display poe-powerSyntax display poe-power Description on fields of the display poe-power command 2493 Existing PoE configuration files will be displayed Display poe-profileDisplay poe-profile index index name profile-name Number ranges from 1 to Description on fields of the display poe-profile command 2495 Syntax poe disconnect ac dc Undo poe disconnect Display poe-profile interfacePoe disconnect Poe enable Syntax poe enable Undo poe enable Poe enable pse Poe legacy enable Poe max-power Poe max-power system viewSyntax poe max-power max-power Undo poe max-power 2499 Poe mode Related command poe priority system viewPoe mode signal spare Undo poe mode Poe pd-description Poe pd-policy prioritySyntax poe pd-description string Undo poe pd-description Syntax poe pd-policy priority Undo poe pd-policy priority Poe priority Syntax poe priority critical high low Undo poe priority Undo poe priority pse pse-id Poe priority system viewPoe priority critical high low pse pse-id Poe update Poe update full refresh filename pse pse-idPoe pse-policy priority Poe pse-policy priority Example # Set the power alarm threshold of PSE 2 to 90% Poe utilization-thresholdPoe-profile Undo poe utilization-threshold pse pse-id Sysname system-view Sysname poe-profile abc Syntax oap connect slot slot-number OAP Module Configuration CommandsOap connect slot Oap reboot slot Syntax oap reboot slot slot-number Acfp Configuration Commands Acfp enable168 Display acfp client-info Display acfp policy-info Client-idis the Acfp client ID, in the range of 1 toPolicy-index Policy index, in the range of 1 to Interface-numberis the interface type and interface number 2511 Display acfp rule-cache Interface type and interface numberInterface-number is the interface type and interface number Will display all the Acfp rule cache information Display acfp rule-info Interface numberClient-id Acfp client ID, in the range of 1 to 2513 # Display Acfp rule information in order of policy Establish 2515 Display acfp server-infoSyntax display acfp server-info Reset acfp rule-cache Type and interface number Acsei Server Configuration Commands Acsei server enableSyntax acsei server enable Undo acsei server enable Acsei server Syntax acsei timer monitor seconds Undo acsei timer monitor Acsei timer clock-syncAcsei timer monitor Display acsei client summary Acsei client rebootAcsei client close Syntax display acsei client info client-id Display acsei client info# Display the summary of all Acsei clients # Display information about all Acsei clients 2521 CPU information of the Acsei client Acsei Client Configuration Commands Acsei-client debug disableAcsei-client debug enable 170 Chkconfig acseid off Syntax chkconfig acseid offAcsei-client debug show Syntax acsei-client debug show Chkconfig acseid on Service acseid condrestartSyntax chkconfig acseid on Syntax service acseid condrestart Service acseid reload Service acseid restartService acseid reload # Load the Acsei client configuration file Service acseid start Service acseid statusSyntax service acseid start Syntax service acseid status Service acseid stop Service acseid stopAny directory of the Linux system # Stop an Acsei client that is running Track Configuration Commands Description on the fields of the display track command171 Display track Track Configuration Commands Display ipx interface IPX Configuration Commands172 Display ipx routing-table Syntax display ipx routing-table network 2533 Display ipx routing-table verboseSyntax display ipx routing-table network verbose Display ipx routing-table protocol Display ipx service-table Inactive Displays inactive service informationDisplay ipx routing-table statistics To 47 characters Syntax display ipx statistics # Display detailed IPX service informationDisplay ipx statistics 2537 SAP Ipx enable Ipx enable node nodeUndo ipx enable Configuration Ipx netbios-propagation Syntax ipx netbios-propagation Undo ipx netbios-propagationIpx encapsulation Ipx encapsulation dot2 dot3 ethernet-2 snap Ipx network Ipx rip import-route staticUndo ipx network Ipx rip import-route static Example # Enable static route redistribution to RIP Ipx rip mtuIpx rip multiplier Syntax ipx rip mtu bytes Undo ipx rip mtu Ipx rip timer update Related command ipx rip timer updateRelated command ipx rip multiplier Example # Specify a RIP update interval of 30 seconds Ipx route load-balance-path 2543 Ipx route max-reserve-path Ipx sap disableSyntax ipx sap disable Undo ipx sap disable Ipx sap gns-disable-reply Ipx sap gns-disable-replyUndo ipx sap gns-disable-reply Ipx sap gns-load-balance Related command ipx sap gns-disable-reply Ipx sap max-reserve-serversIpx sap mtu Syntax ipx sap mtu bytes Related command ipx sap timer update Ipx sap multiplierUndo ipx sap mtu 2547 Ipx sap timer update Ipx serviceRelated command ipx sap multiplier, ipx update-change-only Example # Specify the SAP updating interval as 300 seconds Ipx split-horizon Ipx tickIpx split-horizon Undo ipx split-horizon Ping ipx Ipx update-change-onlySyntax ipx update-change-only Undo ipx update-change-only Reset ipx statistics Reset ipx routing-table statistics protocolSyntax reset ipx statistics 2551 # Clear IPX static route statistics Related command display ipx routing-table statisticsExample # Display IPX routing statistics Voip Configuration Commands 173 Area Area-idArea custom europe north-america Undo area Related command match-template,address, and entity Busytone-t-thSyntax busytone-t-th time-threshold Undo busytone-t-th 2555 Cid display Cid receiveSyntax cid display Undo cid display Syntax cid receive Undo cid receive Cid send Cid typeSyntax cid send Undo cid send View FXS/FXO voice subscriber line view Cng-on Undo cid typeSyntax cng-on Undo cng-on Related command line and vad-on CompressionView POTS/VoIP/VoFR entity view 2559 Relationship between algorithms and bandwidth Codec Bandwidth Voice quality 711 algorithm A-law and µ-law 723 r63 algorithm723 r53 algorithm 726 r16 algorithm 726 r40 algorithm 726 r24 algorithm726 r32 algorithm Algorithm Compression efficiency of IPHC+PPP header Cptone country-type Syntax cptone country-type locale Undo cptone country-typeRegions are supported Countries or regions with supported call progress tones 2565 IEU Cptone tone-type Effect on all voice interfaces of all cards on the deviceSpecial-dial-tone waiting-tone amplitude value Special-dial-tone waiting-tone amplitude Default entity compression G729r8 Default entity payload-size Related command compression Default entity vad-on Default entity vad-onUndo default entity vad-on Vad-on Transmit gain Default subscriber-lineDelay hold Delay rising Delay send-dtmfRelated command em-signal Syntax delay rising milliseconds Undo delay rising Delay send-wink Syntax delay send-wink milliseconds Undo delay send-wink Delay wink-hold Delay wink-risingSyntax delay wink-hold milliseconds Undo delay wink-hold 2573 Description voice entity view Delay start-dialSyntax delay start-dial seconds Undo delay start-dial Description voice subscriber line view Dial-programSyntax dial-program View Voice view Display voice call-info Display voice call-info brief mark tag verboseRange of 0 to Information table Display voice cmc LGS Display voice default all Syntax display voice default allDescription on fields of the display voice cmc command 2579 Description on fields of the display voice default command Display voice entity command Example Display voice entityDisplay voice ipp statistic Display voice entity all mark entity-tag pots voip Voip Configuration Commands Error Displays all the error statistics of IVA module Display voice iva statisticCall Displays the calling statistics in the IVA module 2583 Syntax display voice subscriber-line line-number Related command subscriber-lineDisplay voice subscriber-line 2585 = Busytone CNG Dscp media Dtmf amplitudeSyntax dscp media dscp-value Undo dscp media Syntax dtmf amplitude value Undo dtmf amplitude Dtmf sensitivity-level Dtmf timeDtmf time interval persist milliseconds Undo dtmf time interval persist Dtmf threshold Meaning of the index numbers2589 Index Meaning Value range Remarks Upper limit of the maximum To 4,999, with Echo-canceller 2591 Echo-canceller parameter Related command subscriber-lineand echo-canceller parameterMix-proportion-ratio value talk-threshold value Mix-proportion-ratio talk-threshold Em-phy-parm Em-signalRelated command echo-canceller Undo entity entity-numberall pots voip EntityEntity entity-number pots voip Related command Line Example Related command outband, tunnel-on, and voip called-startFast-connect Fast-connect Hookoff-mode delay bind Example # Enable fast connection for VoIP voice entitySyntax hookoff-mode delay immediate Undo hookoff-mode Hookoff-mode Private-lineand caller-permitcommands when executing Hookoff-timeIncoming calls Syntax hookoff-time time Undo hookoff-time Impedance Line Match-templateUndo line Syntax match-template match-string Undo match-template Them If you want to use and at the same time, you must use themFormat . Other formats, such as and are illegal Such as 0-9. The formats like 0-A are illegal Command, but analog voice subscriber lines do not Nlp-onE1 voice, T, #, and * are not supported currently Nlp-on Payload-size Related command Fast-connectand tunnel-on ExampleOutband 2603 Plc-modeSyntax plc-mode general specific Undo plc-mode Syntax receive gain value Undo receive gain Related command transmit gain and subscriber-lineReceive gain Match-template Reset voice cmc statisticRegister-number Reset voice ipp statistic Reset voice iva statisticRelated command display voice iva statistic Related command display voice ipp statistic Send-busytone enable time seconds Undo send-busytone enable timeSend-busytone Been used to identify nonstandard T38 fax packets Send-ring Shutdown voice entity viewSyntax send-ring Undo send-ring View Voice entity view Shutdown voice subscriber line view Silence-th-spanExample # Change the status of voice entity 4 to Down Undo silence-th-span Slic-gain Subscriber-lineSlic-gain 0 Undo slic-gain 2611 Timer dial-intervalSyntax timer dial-interval seconds Undo timer dial-interval Syntax timer first-dial seconds Undo timer first-dial Timer first-dialTimer hookoff-interval Timer ring-back Timer wait-digitRelated command hookoff-mode Syntax timer ring-back seconds Undo timer ring-back Syntax transmit gain value Undo transmit gain Related command receive gain and subscriber-lineTransmit gain Example # Enable the tunnel function for VoIP voice entity Tunnel-onSyntax tunnel-on Undo tunnel-on View VoIP entity view Related command cng-on Vad-onUndo type Syntax vad-on 2617 Vi-card busy-tone-detectUndo vi-card busy-tone-detect custom index Vi-card cptone-custom 2619 Vi-card rebootSyntax vi-card reboot slot-number Voice-setup Voip called-tunnel enableExample # Reset the voice card of slot Syntax voice-setup Fast-connect Voip timerVoip called-start Vqa dscp Cs7, or efDscp values Keyword Dscp value in binary Dscp value in decimal By default, DSP buffered data is not monitored Vqa dsp-monitor buffer-timeView Voice view Parameter Range 180 to Voip Configuration Commands Dial Plan Configuration Commands Caller-permit Syntax dial-prefix string Undo dial-prefix Related command match-templateonDial-prefix Related command match-templateon page 2599 and send-number Display voice number-substituteExample # Specify 0 as a prefix Syntax display voice number-substitute list-tag Related command number-substitute Dot-matchDot-match end-only left-right right-left Undo dot-match First-rule Max-call in voice dial program viewSyntax first-rule rule-number Undo first-rule Undo max-call set-numberI all Undo max-call Related command max-call in voice entity viewMax-call in voice entity view Related command max-call in voice dial program view Related command match-templateon page 2599 and terminatorExample # Configure the longest-number match policy Number-match Number-substitute Related command rule and substitute voice dial program viewNumber-priority Priority Private-lineUndo priority Syntax private-line string Undo private-line Rule Undo rule rule-tag all Meanings of characters in the string argument 2635 Numbering plan Description Input number typeNumber type Description 2637 Input numbering planOutput numbering plan Select-rule rule-order Undo select-rule rule-order Select-rule search-stop Meanings of integers2639 Integer Meaning Description Meanings of values Select-rule type-firstUndo select-rule type-first 2641 Select-stopSyntax select-stop Undo select-stop Related command dot-matchand match-templateon Send-number Related command number-substituteand rule Substitute subscriber line view/voice entity viewSubstitute called calling list-number Undo substitute called calling Substitute voice dial program view AllNumber-substitute and rule To Pstn are outgoing calls Related command match-templateon page 2599 and timer TerminatorSyntax terminator character Undo terminator Example # Specify the pound sign # as the dial terminator Dial Plan Configuration Commands E1 and T1 Configuration Commands AniAni all ka Undo ani Answer enable Related command cas, timer, reverse, and renewSyntax answer enable Undo answer enable Ani-offset Related command re-answer enable and timer dl re-answer CallmodeCas Callmode segment terminal Clear-forward-ack enable Example # Enter the R2 CAS view of TS group 2651 Related command modeDisplay voice subscriber line Dl-bits CNG/CED 2653 Default values of signals in R2 digital line signalingSignal Default rx-bits Abcd Default tx-bits Abcd Dtmf enable Related command seizure-ack enable and answer enableSyntax dtmf enable Undo dtmf enable Related command timer dtmf Final-callednum enable Syntax final-callednum enable Undo final-callednum enableRelated command register-valuedigital-end 2655 Force-metering enable Group-b enableSyntax force-metering enable Undo force-metering enable Syntax group-b enable Undo group-b enable Related command register-valuereq-switch-groupb 2657 Syntax mode zone-name default-standard Undo mode Mode Related command register-valueand force-metering enable Example # Adopt Hongkong default R2 signalingPcm Syntax pcm a-law µ-law Undo pcm Syntax pri-set timeslot-list range Undo pri-set Example # Adopt µ-law companding for signal quantizationPri-set Re-answer enable Syntax re-answer enable Undo re-answer enableRelated command answer enable and timer dl re-answer 2661 Req-callednum-and-switchgroupa req-callingcategory req Changeover to Group a signal value, in the range 1 toDemand-refused digit-end nullnum req-billingcategory Subscriber-busy subscriber-charge subscriber-idle 2663 Related command group-b enable RenewSyntax renew Abcd Undo renew Seizure-ack enable Related command cas and reverseRelated command cas and renew Reverse Related command timer dl seizure Select-modeView CAS view Timeslots Sendring ringbusy enable Related command cas and trunk-directionRelated command timer ring 2667 Signal-value Related command Subscriber line ExampleSpecial-character Syntax special-character character number Different signal values Undo special-character character number Related command timeslot-setand pri-set Tdm-clockExample # Enter the view of voice subscriber line 1/015 Syntax tdm-clock internal line primary Undo tdm-clock Timer dl Release-guardView R2 CAS view 2671 Timer dtmf Syntax timer dtmf time Undo timer dtmf Timer register-pulse persistence Related command dtmf enableTimer register-pulse persistence time Undo timer register-pulse persistence Timer register-complete group-b Related command timer register-completegroup-bTimer register-complete group-b time Undo timer register-complete group-b Timer ring Timer ring ringback ringbusy timeUndo timer ring ringback ringbusy Timeslot-set Related command subscriber line and cas Trunk-direction Related command cas and select-mode Ts block open query reset timeslots timeslots-listCAS view 2677 Related command cas FAX Over IP Configuration Commands Default entity fax Syntax display voice fax statistics Display voice faxExample # Set the maximum fax rate to 9,600 bps globally 2681 Faxvofrstandardswitch FAXVOFRFRF11SWITCHWaitdpbegdemodulatetimeout Waitdpbegmodulatetimeout Undo fax baudrate Fax baudrate 2400 4800 9600 14400 disable voiceFax baudrate Undo fax ecm Fax ecmSyntax fax ecm Fax level Fax local-train thresholdSyntax fax level level Undo fax level 2685 Example # Configure the fax local training threshold to Example # Configure NSF for fax signal transmissionFax nsf-on Syntax fax nsf-on Undo fax nsf-on Undo fax protocol Fax protocolFax protocol pcm g711alaw g711 μlaw VoFR entities only support the PPP training mode Fax train-modeFax train-mode local ppp Undo fax train-mode Reset voice fax statistics Reset voice fax statisticsVoip h323-conf tcs-t38 Voip h323-conf tcs-t38 FAX Over IP Configuration Commands Related command match-templateon page 2599, entity on 177Display voice gateway Syntax area-id string Undo area-id string Gkid Gk-clientSyntax gk-client Related command gk-id Gk-2nd-idExample # Enter gatekeeper client view Undo gk-2nd-id Gk-security call enable Related command area-id,gw-id,gk-2nd-id,gw-address,ras-onSyntax gk-security call enable Undo gk-security call enable Gk-id Gk-security register-pwd cipher simple password Gk-security register-pwdGw-address Undo gk-security register-pwd Undo gw-id Gw-idUndo gw-address Related command gw-id,gw-address, and gk-id Ras-onVoip h323-descriptor Syntax ras-on 323 Configuration Commands SIP Configuration Commands 178Display voice sip call-statistics Syntax display voice sip call-statistics TPT Message Display voice sip register-state Outband sipDisplay voice sip register-state Syntax outband sip Undo outband Default port number is ProxyUndo proxy ipv4 SIP client view Register-enable Register-enable off onUndo register-enable Registrar ipv4 Reset voice sip SipSip-comp Syntax sip Sip-comp agent Undo sip-comp callee fromSIP client view SIP request messages Sip-comp server Sip-domainUndo sip-comp server View SIP client view 2707 Source-ipSyntax source-ip ip-address Undo source-ip SIP Configuration Commands Wildcard-register enable Syntax wildcard-register enable Undo wildcard-registerExample # Enable fuzzy telephone number registration 2709 SIP Configuration Commands Vofr Configuration Commands 179Address Undo address vofr-dynamic vofr-static Cid select-mode Related command Trunk-idand address ExampleCall-mode Related command Vofr Example # Set the CID selection mode to min-poll on DlciDisplay fr vofr-info Interface Dlci view Entity vofr Outband vofrUndo entity entity-number vofr Outband vofr Undo seq-number Seq-numberSeq-number Trunk-id Related command call-modeTimestamp Voice bandwidth VofrView Interface Dlci view 2717 Related command call-mode Vofr frf11-timer Vofr frf11-timer timeUndo vofr frf11-timer Hang up successfully in the FRF.11 trunk mode Vofr Configuration Commands Voice Radius Configuration Commands Aaa-clientAccounting Syntax aaa-client Related command acct-methodand accounting Accounting-didSyntax accounting-did Undo accounting-did View Voice AAA client view Related command accounting and accounting-did # Restore the default accounting methodAcct-method Example # Set the accounting method to start-ack Authentication Authentication-didSyntax authentication Undo authentication Related command gw-access-numberand authorization Authorization Related command authorization-didSyntax authorization Undo authorization 2725 Authorization-did Related command gw-access-numberand authenticationSyntax authorization-did Undo authorization-did Related command authentication-did 2727 Related command gw-access-numberCallednumber receive-method Related command gw-access-numberand process-config Card-digitCdr Syntax card-digit card-digit Undo card-digit Related command display voice call-history-record # Set the alarm threshold for CDRs to 10%Undo cdr all buffer duration threshold Example # Set the number of CDRs that can be saved to Gw-access-number and aaa-client Display voice access-numberDisplay voice access-number 2731 Display voice call-history-record 2733 Related command cdrExample # Display call records by calling number Display voice radius statistic Syntax display voice radius statistic Related command reset voice radius statistic 2735VORDS=AAA AAA=VORDS Gw-access-number CMC=VORDS Password-digit # Add the access number 179 and enter access number view# Delete the access number # Delete all access numbers Process-config # Restore the default dialing process for the access number 2739 Redialtimes Undo redialtimes Reset voice radius statistic Gw-access-numberand process-configSelectlanguage Display voice radius statistic Voice Radius Configuration Commands

3Com MSR 30 Rule in basic IPv6 ACL view, # Clear the statistics about the IPv6 ACL named flow

Models: MSR 50 MSR 30

# Clear the statistics about the IPv6 ACL named flow.

rule (in basic IPv6 ACL view)

undo rule rule-id[ fragment logging source time-range ] *