Display interface virtual-template

504CHAPTER 31: PPP AND MP CONFIGURATION COMMANDS

Table 82 Description on the fields of the display interface mp-group command

Field	Description

LCP initial	Link control protocol (LCP) negotiation is complete
Physical	Physical type of the interface
Last 300 seconds input: 0 bytes/sec	Average rate of input packets and output packets in the
0 packets/sec	last 300 seconds (in bps)
Last 300 seconds output: 0 bytes/sec
0 packets/sec
0 packets input, 0 bytes, 0 drops	Total amount of input packets of the interface (in the
	number of packets and in bytes respectively), and the
	number of dropped packets within the input packets
0 packets output, 0 bytes, 0 drops	Total amount of output packets of the interface (in the
	number of packets and in bytes respectively), and the
	number of dropped packets within these output
	packets

Syntax display interface virtual-template [ number ]

View Any view

Parameter number: Virtual template (VT) number, which can be the number of any existing VT.

Description Use the display interface virtual-templatecommand to view the information about a VT. If you do not provide the number argument, this command will display the information about all the existing VTs.

Related command: interface virtual-template.

Example # View the information about VT 1.

<Sysname> display interface virtual-template 1 Virtual-Template1 current state: UP

Line protocol current state: UP (spoofing)

Description: Virtual-Template1 Interface

The Maximum Transmit Unit is 1500

Internet protocol processing : disabled

Link layer protocol is PPP

LCP initial

Physical is None

Output queue : (Urgent queue : Size/Length/Discards) 0/50/0

Output queue : (Protocol queue : Size/Length/Discards) 0/500/0

Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0

Last 300 seconds input: 0 bytes/sec 0 packets/sec

Last 300 seconds output: 0 bytes/sec 0 packets/sec 0 packets input, 0 bytes, 0 drops

0 packets output, 0 bytes, 0 drops

Refer to Table 82 for the description on the other fields.

Page 504

Image 504

3Com MSR 30, MSR 50 manual Display interface virtual-template, Syntax display interface virtual-template number

Contents

H3C MSR 20/30/50 Series Routers 3Com Corporation Campus Drive Marlborough, MA USA United States Government Legend Contents Adsl Interface Configuration Commands POS Interface Configuration CommandsGeneral Ethernet Interface Configuration Commands Fundamental Serial Interface Configuration Commands Fundamental CE1/PRI Interface Configuration Commands Fundamental CT1/PRI Interface Configuration Commands 14 E1-F Interface Configuration Commands 15 T1-F Interface Configuration Commands Fundamental CE3 Interface Configuration CommandsFundamental CT3 Interface Configuration Commands Isdn BRI Interface Configuration Commands ATM Configuration CommandsDCC Configuration Commands Basic Dlsw Configuration Commands 340 Frame Relay Configuration Commands Garp Configuration Commands Gvrp Configuration CommandsHdlc Configuration Commands Lapb and X.25 Configuration Commands 425 Display x25 hunt-group-info Display x25 map 426 451 X25 pvc X25 queue-length 453 X25 receive-threshold 454455 Link Aggregation Configuration Commands Link Aggregation Debugging CommandsModem Configuration Commands Port Mirroring Configuration Commands PPP Link Efficiency Mechanism Configuration Commands Pppoe Server Configuration CommandsPppoe Client Configuration Commands PPP Debugging Commands Bridging Configuration CommandsIsdn Configuration Commands Debugging ppp Mstp Configuration Commands Vlan Configuration Commands PORT-BASEDVLAN Configuration CommandsVoice Vlan Configuration Commands Port Isolation Configuration Commands Cpos Interface Configuration Commands ARP Configuration Commands Gratuitous ARP Configuration Commands ARP Source Suppression Configuration CommandsAuthorized ARP Configuration Commands Proxy ARP Configuration Commands Dhcp Relay Agent Configuration Commands Dhcp Client Configuration CommandsDhcp Snooping Configuration Commands Bootp Client Configuration Commands DNS Configuration Commands IP Accounting Configuration CommandsIP Addressing Configuration Commands IP Performance Configuration Commands IP Unicast Policy Routing Configuration Commands UDP Helper Configuration CommandsUrpf Configuration Commands Fast Forwarding Commands NAT-PT Configuration Commands 840 Display tcp ipv6 status 842Display natpt address-group 863 Display natpt aging-time 864 display natpt all Dual Stack Configuration Commands Tunneling Configuration Commands69 IPV6 Unicast Policy Routing Configuration Commands Terminal Access Configuration Commands IP Routing Table Commands BGP Configuration Commands Ebgp-interface-sensitive 977981 Log-peer-change 983 Peer advertise-communityBGP/BGP-VPN instance view BGP Debugging Commands IS-IS Configuration Commands IS-IS Debugging Commands Ospf Configuration Commands 1155 Snmp-agent trap enable ospf 11171128 1140 RIP Configuration Commands Routing Policy Common Configuration Commands1179 79 IPV4 Routing Policy Configuration Commands 80 IPV6 Routing Policy Configuration CommandsStatic Routing Configuration Commands 82 IPV6 BGP Configuration Commands 1223 12431246 83 IPV6 IS-IS Configuration Commands 84 IPV6 OSPFV3 Configuration Commands 85 IPV6 Ripng Configuration Commands 86 IPV6 Static Routing Configuration CommandsMulticast Routing and Forwarding Configuration Commands Delete ipv6 static-routes all 1325 ipv6 route-static Igmp Configuration Commands Msdp Configuration CommandsCache-sa-enable 1365 display msdp brief 1366 PIM Configuration Commands 1376 1421 14221429 MLD Configuration Commands 93 IPV6 PIM Configuration Commands1451 Multicast VPN Configuration Commands 1495Display multicast-domain vpn-instance share-group 1505 Mpls Basics Configuration Commands Mpls TE Configuration Commands Mpls rsvp-te reliability 1610 Mpls rsvp-te resvconfirm 1611 Mpls L2VPN Configuration Commands Mpls L3VPN Configuration Commands VAM Server Configuration Commands 1697 VAM Client Configuration Commands Ipsec Profile Configuration CommandsDvpn Tunnel Configuration Commands GRE Configuration Commands Traffic Policing TP Configuration Commands Traffic Shaping Configuration CommandsLine Rate Configuration Commands Defining Class Commands Fifo Queuing Configuration Commands PQ Configuration CommandsCQ Configuration Commands WFQ Configuration Commands QOS Token Configuration Commands Priority Mapping Table Configuration CommandsPort Priority Configuration Commands Port Priority Trust Mode Configuration Commands FR QOS Configuration Commands 126 802.1X Configuration CommandsAAA Configuration Commands access-limit Reset dar session Radius Configuration Commands 19271958 Hwtacacs Configuration Commands Packet Filter Firewall Configuration Commands Aspf Configuration Commands aging-time MAC Authentication Configuration CommandsNAT Configuration Commands PKI Configuration Commands Portal Configuration Commands RSH Configuration Commands rshCommon Configuration Commands 138 IPV4 ACL Configuration Commands Ipsec Configuration Commands IKE Configuration Commands 142 SSH2.0 Configuration Commands Sftp Configuration Commands bye SSL Configuration Commands Backup Center Configuration Commands 146 IPV4-BASEDVRRP Configuration CommandsVrrp Configuration Commands for IPV6 Device Management Commands NQA Client Configuration Commands Temperature-alarm enable 2263 Temperature-limit2262 2276 NQA Server Configuration Commands Netstream Configuration CommandsNTP Configuration Commands Rmon Configuration Commands Snmp Configuration Commands File System Configuration Commands cd Configuration File Management Commands FTP Server Configuration CommandsFTP Client Configuration Commands ascii Tftp Client Configuration Commands System Maintaining Commands System Debugging CommandsBasic Configuration Commands Information Center Configuration Commands User Interface Configuration Commands 2460 MAC Address Table Management Configuration Commands POE Configuration CommandsOAP Module Configuration Commands Acfp Configuration Commands Acsei Server Configuration CommandsAcsei Client Configuration Commands Track Configuration Commands Voip Configuration Commands address 2551 Reset ipx routing-table statistics protocol2546 Area 2554 area-id 2592 Dial Plan Configuration Commands 175 E1 and T1 Configuration Commands aniCaller-permit 2639 FAX Over IP Configuration Commands 177 H.323 Configuration CommandsSIP Configuration Commands Vofr Configuration Commands Voice Radius Configuration Commands aaa-client2716 2734 About this Guide Lists icon conventions that are used throughout this guideLists text conventions that are used throughout this guide Text Conventions Related Documentation Alphabetical Listing of Commands Area Ospf view 1108 area OSPFv3 viewPage Page Rp IPv6 PIM view 1464 c-rp PIM view Page Display bgp vpnv4 vpn-instancerouting-table Page Display ipv6 policy-based-route statistics Page Page Page Page Page Fr compression frf9 385 fr compression iphc Page Igmp last-member-query-interval Ipv6 nd autoconfig managed-address-flag Page Page Page Mpls te resv-style 1631 mpls te retry 2308 Peer ebgp-max-hopBGP/BGP-VPN instance view Peer keep-all-routesBGP/BGP-VPN instance viewPeer allow-as-loopBGP/BGP-VPN instance view Peer next-hop-localBGP/BGP-VPN instance view Peer preferred-valueBGP/BGP-VPN instance viewPeer next-hop-invariableBGP-VPNv4 subaddress family view Peer public-as-onlyBGP/BGP-VPN instance view Pppoe-servermax-sessionsremote-mac Primary accounting Hwtacacs scheme view Qos wred ip-precedence 1850 qos wred queue table Reset aspf session 2007 reset atm interface 112 reset bgp Reset pim ipv6 control-message counters Page Page Ssl client-policy 2215 ssl server-policy Statistics interval 1562 step for IPv4 2100 step for IPv6Page Page Page X29 timer inviteclear-time Page Public ATM and DSL Interface Commands Display interface atmSyntax display interface atm interface-number Reset atm interface Syntax reset atm interface atm interface-numberInterface atm Configuration Commands CableClock Code Code ami hdb3Code ami b8zs Undo code Differential-delay Display interface ima-groupSyntax display interface ima-group group-interfacenumber 115 Frame-format View ATM E1/T1 interface view ParameterATM direct mapping CRC4 ADM ESF ADM Frame-length Ima ima-groupSyntax frame-length 32 64 128 Undo frame-length Syntax ima ima-group group-number Undo ima ima-group Ima-clock Example # Add the link of ATM E1 interface 5/0 to IMA groupSyntax ima-clock ctc link-number number itc Undo ima-clock Ima-standard Ima-testIma-test link-number number pattern-id id Undo ima-test By default, IMA group interface test is disabled Interface ima-groupLoopback Syntax loopback cell local payload remote Undo loopback Min-active-links ScrambleSyntax min-active-links number Undo min-active-links Syntax scramble Undo scramble Parameter None Slave Sets the clock mode as slave Syntax cable long short Undo cableView ATM E3/T3 interface view Frame-format g751-adm g751-plcp g832-adm Frame-format cbit-adm cbit-plcp m23-adm m23-plcp Loopback cell local payload remote ATM E3/T3 Interface Configuration Commands Frame-format sdh sonet Loopback cell local remote View ATM OC-3c interface view, STM-1 interface view 129 ATM OC-3C/STM-1 Interface Configuration Commands Shdsl Interface Configuration Commands ActivateSyntax activate Undo activate View ATM G.SHDSL interface view Display dsl configuration Field Description Display dsl status Syntax display dsl status interface atm interface-number133 Gspn Description on the fields of the display dsl status command 135 Display dsl version Syntax display dsl version interface atm interface-numberITU G991.2 Annex A, ITU Shdsl mode Shdsl annex Example # Set the operating mode of interface ATM 5/0 to CO Shdsl psdShdsl rate Syntax shdsl psd asymmetry symmetry Undo shdsl psd Single-pair interface rate to auto mode Kbps four-wire G.SHDSL interface rate is 4,624 kbps# Configure ATM 5/0 to operate in the auto-negotiation mode Use the undo shdsl snr-margincommand to restore the default Shdsl wire Shdsl wire 2 4-auto-enhanced 4-enhanced 4-standardUndo shdsl wire 141 Shdsl Interface Configuration Commands Adsl Interface Configuration Commands View ATM Adsl interface viewExample # Activate Adsl interface 2/0 Adsl standard Adsl tx-attenuationAdsl standard auto g9923 g9925 gdmt glite t1413 Undo adsl standard Bootrom update file 145 Display dsl configuration 147 LS0US FieldDescription Dslam 149 Bdcm Adsl Interface Configuration Commands POS Interface Configuration Commands CrcSyntax crc 16 Undo crc Display interface pos Syntax display interface pos interface-number 153 LCP opened, Ipcp opened, IP6CP opened Display ip interface pos Display ipv6 interface posDisplay ip interface pos interface-number Syntax display ipv6 interface pos interface-number Flag Related command display interface pos Example # Set the SDH overhead byte J0 of POS1/0 interface# Set the framing format on interface POS 1/0 to SDH Link-protocol Loopback local remoteLocal Internal loopback Remote External loopback Mtu That the state of the link layer protocol is reported upInterfaces cannot be connected successfully Syntax mtu size Example # Enable payload scrambling on interface POS 1/0 ThresholdSyntax threshold sd sf value Undo threshold sd sf 159 Example # Set the SD threshold to 10e-4 for POS 1/0 General Ethernet Interface Configuration Commands Combo enableRelated command display port combo and shutdown Description Display brief interface Special characters used in regular expressionsCharacter Meaning Related command interface Example # Display brief information of interfaces163 Display interface Acronyms for different types of InterfacePvid Interface name Acronyms 165 Field Output queue Fifo queuing 167 Related command speed DuplexFlow-control Syntax duplex auto full half Undo duplex Interface Can be represented as 1/0E1/0 Syntax loopback external internal Undo loopback Support for these two commands varies with device models Port link-modePort link-mode bridge route Undo port link-mode Reset counters interface Example # Configure Ethernet1/0 to work in bridge modeView User view 171 Shutdown Speed Related command duplex 173 General Ethernet Interface Configuration Commands Broadcast-suppression Display loopback-detection Display portSyntax display loopback-detection Display port hybrid trunk Display port-group manual Display port-group manual all name port-group-nameExamples Flow-interval Group-memberSyntax flow-interval interval Undo flow-interval Undo group-member interface-list Loopback-detection control enable 179 Loopback-detection enable Related command loopback-detection control enableLoopback-detection interval-time View System view/Ethernet interface view Loopback-detection per-vlan enable Related command display loopback-detection181 Optical port of a Combo port does not support this command MdiMulticast-suppression Mdi across auto normal Port-group Port-group manual port-group-name aggregation agg-idUndo port-group manual port-group-name Currently, these two commands are not supported Unicast-suppressionVirtual-cable-test Syntax virtual-cable-test 185 Page Timer hold Example # Configure MTU for Ethernet1/0 to be 1,000 bytesSyntax timer hold seconds Undo timer hold Configuration Commands for Ethernet Interfaces in Route Mode Fundamental Serial Interface Configuration Commands Async modeSyntax async mode flow protocol Undo async mode Baudrate Clock serial interface view Undo baudrateClock dteclk1 dteclk2 dteclk3 dteclk4 dteclkauto View Serial interface view Dteclk1 191Clock selection option Description Code nrzi Country-codeSyntax code nrzi Undo code View Synchronous serial interface view Example # Configure to adopt 32-bit CRC DetectSyntax crc 16 32 none Undo crc Asynchronous serial interface detect dsr-dtr Eliminate-pulse Syntax eliminate-pulse Undo eliminate-pulseView Asynchronous serial interface view Idle-mark Invert receive-clockSyntax idle-mark Undo idle-mark Syntax invert receive-clock Undo invert receive-clock Invert transmit-clock Syntax invert transmit-clock Undo invert transmit-clock Mtu on serial interfaces Syntax loopback Undo loopback197 Physical-mode Phy-mruSyntax physical-mode async sync Syntax phy-mru size Undo phy-mru Reverse-rts Syntax reverse-rts Undo reverse-rts199 Virtualbaudrate Virtualbaudrate virtualbaudrateUndo virtualbaudrate Baudrate Fundamental CE1/PRI Interface Configuration Commands Channel-set CE1/PRI interface view Clock CE1/PRI interface view Clock Code CEI/PRI interface view Controller e1Controller e1 number Detect-ais Crc 16 32 noneSyntax detect-ais Undo detect-ais Description on the fields of the command Display controller e1Syntax display controller e1 interface-number 205 Error-diffusion restraint config Undo error-diffusion restraint config Error-diffusion restraint enable Error-diffusion restraint restart-channelBy default, error packets diffusion restraint is enabled Example # Enable error packets diffusion restraint Frame-format CE1/PRI interface view Idlecode CE1/PRI interface viewTwo types of line idle code are available 0x7E and 0xFF Itf CE1/PRI interface view Itf number number type 7e ffUndo itf type number Loopback CE1/PRI interface view Pri-set CE1/PRI interface viewLoopback local payload remote Pri-set timeslot-list list Reset counters controller e1 Reset counters controller e1 interface-numberCommand Display controller e1 interface-number command Using CE1/PRI interface view Using ce1 e1Undo using Fundamental CT1/PRI Interface Configuration Commands Alarm-thresholdLevel-2 Level-2 , level-3 , and level-4 Bert CT1/PRI interface view Bert pattern 215 220 time minutes unframedUndo bert Ranges from 1 to 1,440 Cable CT1/PRI interface view Channel-set CT1/PRI interface view655ft Clock CT1/PRI interface view View CT1/PRI interface view Code CT1/PRI interface view Controller t1Ami Adopts AMI line code format # Set the line code format of the interface T1 2/0 to AMI Data-coding CT1/PRI interface view Data-coding inverted normalUndo data-coding Display controller t1 Syntax display controller t1 interface-number219 Clock or slave for the line clock 221 Error-diffusion restraint config By default, the function is disabled Example # Enable error packet diffusion restraint223 Support of this command varies with device model Error packet diffusion restraint functionFdl Set-number argument is a channel set number Frame-format CT1/PRI interface view Idlecode CT1/PRI interface viewFrame-format esf sf Itf CT1/PRI interface view Loopback CT1/PRI interface viewSyntax itf number number type 7e ff Undo itf number type Syntax loopback local payload remote Remote Enables the interface to perform remote loopback # Enabled remote loopback on interface T1 2/0Pri-set CT1/PRI interface view Loopback on the CT1/PRI interface Reset counters controller t1 Reset counters controller t1 interface-numberFor a CT1/PRI interface # Clear the controller counter for CT1/PRI interface T1 2/0 Sendloopcode 229 Fundamental CT1/PRI Interface Configuration Commands E1-F Interface Configuration Commands Display fe1Display fe1 serial interface-number Fe1 cable Fe1 clockFe1 cable long short Undo fe1 cable Fe1 code Fe1 detect-ais Fe1 frame-format Fe1 loopback Local Sets the interface in internal loopback mode Fe1 timeslot-listUndo fe1 loopback Syntax fe1 timeslot-list list Undo fe1 timeslot-list Related command fe1 unframed Fe1 idlecodeFe1 itf Syntax fe1 idlecode 7e ff Undo fe1 idlecode Fe1 unframed Fe1 unframedUndo fe1 unframed Related command fe1 timeslot-list T1-F Interface Configuration Commands Display ft1Display ft1 serial interface-number Description on the fields of the display ft1 serial command 241 Bert statestopped, not completed Ft1 bert T1-F interface view Ft1 bert pattern 215 220 time minutes unframedUndo ft1 bert T1-F interface view Ft1 cable Syntax ft1 cable long decibel short length Undo ft1 cableView T1-F interface view 243 Ft1 clock Ft1 codeFt1 clock master slave Undo ft1 clock Ft1 data-coding Ft1 data-coding inverted normalUndo ft1 data-coding Ft1 fdl Ft1 frame-format Ft1 idlecode Ft1 itfFt1 idlecode 7e ff Undo ft1 idlecode Use the undo ft1 loopback command to restore the default Ft1 loopbackFt1 loopback local payload remote Undo ft1 loopback # Set T1-F interface Serial 2/0 in local loopback mode Ft1 timeslot-list249 Ft1 alarm-threshold Undo ft1 alarm-thresholdOn the T1-F interface Ft1 sendloopcode 251 T1-F Interface Configuration Commands Fundamental CE3 Interface Configuration Commands Bert CE3 InterfaceBert pattern 27 211 215 qrss time number unframed Clock CE3 interface view Controller e3Display controller e3 Example # Enter the view of interface E3 2/0 Display controller e3 Syntax display controller e3 interface-number255 Fundamental CE3 Interface Configuration Commands E1 bert 257 Related command e1 unframed E1 channel-setE1 set clock Syntax e1 line-numberset clock master slave E1 set frame-format Undo e1 line-numberset clockView CE3 interface view 259 E1 set loopback E1 shutdownUndo e1 line-numbershutdown Related command e1 channel-set E1 unframedFe3 Undo e1 line-numberunframed CE3 interface in FE3 mode view Set the DSU mode or the subrateUse the undo fe3 command to restore the default These two commands are only available in E3 mode Loopback CE3 interface view National-bitNational-bit 0 Undo national-bit Using CE3 interface view Related command controller e3Syntax using ce3 e3 Undo using Example # Set the national bit to 0 on interface E3 2/0 Fundamental CT3 Interface Configuration Commands Alarm CT3 interface viewAlarm detect generate ais febe idle rai Undo alarm detect generate ais febe idle rai # Enable CT3 interface T3 2/0 to send AIS alarm signals Bert CT3 interface view Cable CT3 interface view Clock CT3 interface viewSyntax cable feet 267 Related command display controller t3 Controller t3Example # Enter the view of interface T3 2/0 None Adopts no CRC Display controller t3 Syntax display controller t3 interface-number269 AIS Configurable and default to line 271 LOS, LOF, AIS, or RAI Feac CT3 interface view Frame-format CT3 interface view Ft3Frame-format c-bit m23 275 Loopback CT3 interface view Mdl CT3 interface view 277 T1 alarm # Set LIC to hello for CT3 interface T3 2/0# Send path messages on CT3 interface T3 2/0 T1 bert 279 Related command t1 unframed T1 channel-set T1 sendloopcode 281 T1 set clock T1 set frame-format T1 set loopback T1 set fdlView CT3 interface view 283 T1 show Description on the fields of the t1 show command T1 shutdown285 Related command t1 channel-set T1 unframedUndo t1 line-numbershutdown Syntax t1 line-numberunframed undo t1 line-numberunframed Using CT3 interface view Using ct3 t3Ct3 Sets the CT3 interface to operate in channelized mode T3 Sets the CT3 interface to operate in unchannelized mode Fundamental CT3 Interface Configuration Commands Isdn BRI Interface Configuration Commands Loopback Isdn BRI interface viewLoopback b1 b2 both Fixed Isdn interfaces on your router, if there is any Isdn BRI Interface Configuration Commands ATM Configuration Commands Related command atm-classAtm class Atm-class Related command atm class Atm-link checkSyntax atm-link check Undo atm-link check View ATM P2P sub-interface view Related command Display atm interface Example Display atm classDisplay atm class atm-class-name Display atm interface Syntax display atm interface atm interface-number Display atm map-info 295 Display atm pvc-group VPI/VCIPVC-NAME State Display atm pvc-info 297 Encapsulation Syntax encapsulation aal5-encap Undo encapsulationIndex Ip-precedence Example # Enter Atm1/0 interface299 Related command pvc-group,pvc Map bridgeView PVC view/ATM Class view # Configure an IP address 10.1.1.1/16 for the VE interface Map ip# Create PVC 1/102 on the ATM interface Atm2/0 Map ip inarp minutes broadcast Undo map ip inarp Map ppp Syntax map ppp virtual-template vt-number Undo map ppp # Create a PPPoA map using the VT interface created # Create PVC 1/101 on interface Atm1/0303 Oam ais-rdi Oam frequency Undo oam frequency305 Oamping interface Pvc Related command display atm pvc-info,pvc max-number VCI range for each type of ATM interface307 Interface type Related command ip-precedence,pvc Pvc-groupPvc max-number Syntax pvc max-number max-number Undo pvc max-number Pvp limit Undo pvp limit vpi Service cbr Example # Set the traffic of VP with vpi 1 to 2MInterface type Value range of output-pcr Service ubr Service vbr-nrtRelated command service vbr-nrt,service vbr-rt,service ubr Syntax service ubr output-pcr Service vbr-rt Related command service ubr, service vbr-rt, and service cbr Parameters None # Bring up ATM 5/0313 Transmit-priority Syntax transmit-priority value Undo transmit-priority DCC Configuration Commands Related command dialer bundle-memberDialer bundle Dialer bundle-member Related command dialer bundle Dialer callback-center Dialer call-in 317 Related command dialer callback-center Related command interface dialerDialer circular-group Dialer enable-circular Dialer enable-circularUndo dialer enable-circular Bundle-member command Related command dialer circular-group Related command dialer thresholdDialer flow-interval Dialer isdn-leased physical interface view Dialer number Syntax dialer number dial-number Undo dialer number321 Related command dialer route Dialer priorityDialer queue-length Syntax dialer priority priority Undo dialer priority Dialer route 323 Dialer threshold Dialer timer autodial Related command dialer flow-interval325 Dialer timer compete Dialer timer enable Dialer timer idleSyntax dialer timer enable seconds Undo dialer timer enable Syntax dialer timer idle seconds Undo dialer timer idle Dialer timer wait-carrier Dialer userSyntax dialer user username Undo dialer user Dialer-group Example # Add a remote username routerbSyntax dialer-group group-number Undo dialer-group 329 Related command dialer-rule Example # Add interface Serial 2/0 to dialer access groupDialer-rule Undo dialer-rule group-number Related command dialer-group Display dialerAny view Number Display interface dialer Display interface dialer numberNumber Dialer interface number Information about all the dialer interfaces Interface dialer Syntax interface dialer number Undo interface dialer number333 Ppp callback Ppp callback ntstringPpp callback client server Undo ppp callback client server Related command ppp callback Undo ppp callback ntstring335 DCC Configuration Commands Basic Dlsw Configuration Commands Example # Configure Serial 1/0 to use Nrzi encodingDisplay dlsw circuits Syntax display dlsw circuits circuit-id verbose Display dlsw information Display dlsw information local ip-address Display dlsw remote # Display the local information about capabilities exchangeSyntax display dlsw remote ip-address 339 Display dlsw reachable-cache Display dlsw reachable-cacheInformation of DLSw # Display the reachability information of DLSw Description on the fields of the display llc2 command Display llc2Syntax display llc2 circuit circuit-id 341 Dlsw enable Syntax dlsw enable Undo dlsw enableDlsw bridge-set # Enable DLSw Dlsw ethernet-frame-filter343 Dlsw local # Allow the router to access SAP addresses 12 Dlsw reachable345 # Permit access to user-configured MAC addresses only Dlsw reachable-cacheDlsw remote Undo dlsw remote ip-address 347 Related command sdlc mac-map remote Dlsw reverseDlsw max-transmission Syntax dlsw reverse mac-address Dlsw multicast Undo dlsw multicast349 Dlsw timer Link-protocol sdlc Syntax link-protocol sdlc351 Llc2 max-ack Llc2 max-pduSyntax llc2 max-ack length Undo llc2 max-ack Syntax llc2 max-pdu length Undo llc2 max-pdu Llc2 max-send-queue Llc2 max-transmissionSyntax llc2 max-send-queue length Undo llc2 max-send-queue 353 Llc2 modulo Llc2 receive-windowLlc2 modulo 8 Undo llc2 modulo Llc2 timer ack Llc2 timer ack-delaySyntax llc2 timer ack mseconds Undo llc2 timer ack 355 Llc2 timer busy Llc2 timer detectSyntax llc2 timer busy mseconds Undo llc2 timer busy Syntax llc2 timer detect mseconds Undo llc2 timer detect Llc2 timer poll Syntax llc2 timer poll mseconds Undo llc2 timer poll357 Llc2 timer reject Reset dlsw circuitsReset dlsw reachable-cache Reset dlsw tcp Syntax reset dlsw tcp ip-addressDescription on the fields of the reset dlsw tcp command 359 Sdlc controller Sdlc enable dlsw Syntax sdlc enable dlsw Undo sdlc enable dlswSdlc mac-map local 361 Sdlc mac-map remote Sdlc max-pdu Sdlc max-send-queueSyntax sdlc max-pdu number Undo sdlc max-pdu Syntax sdlc max-send-queue length Undo sdlc max-send-queue Sdlc max-transmission Sdlc moduloView Synchronous serial interface view Specifies the modulus value to be Related command sdlc sap-map remote Sdlc sap-map local365 Related command sdlc sap-map local Sdlc sap-map remoteSdlc simultaneous Syntax sdlc simultaneous Undo sdlc simultaneous Sdlc status Sdlc status primary secondaryUndo sdlc status primary secondary Sdlc timer ack Sdlc timer lifetimeSyntax sdlc timer ack mseconds Undo sdlc timer ack Sdlc timer poll Syntax sdlc timer poll mseconds Undo sdlc timer pollSdlc window Syntax sdlc window length Undo sdlc window Sdlc xid Undo sdlc xid sdlc-address Frame Relay Configuration Commands AnnexgDisplay fr compress Annexg dce dte Display fr dlci-switch Related commands fr compression frf9 Related command fr inarp Example Display fr inarp-infoDisplay fr interface # Display statistics about frame relay Inarp packets Display fr lmi-info Range 0 to# Display information about all frame relay interfaces Frame Related command fr compression iphc Display fr iphc375 Display fr map-info Mappings or the one for the specified interfaceWhether dynamic address mapping operates normally Fr map ip , fr inarp Display fr map-info pppofr 377Dlci = 100, IP Inarp Display fr pvc-info 1007Statistics about data transmitted and received on them Fr dlci Display fr statistics 379 Display interface mfr MTU Display mfr 381 Description on the fields of the display mfr command LID Display x25 template Syntax display x25 template name383 Related command x25 template, x25-template Fr compression frf9 Fr compression iphcSyntax fr compression frf9 Undo fr compression View Subinterface point-to-point view Fr dlci Undo fr compression iphcUndo fr dlci dlci-number Fr dlci-switch Use the undo fr dlci command to cancel the configurationUndo fr dlci-switch in-dlci Related command fr switching Fr inarp Syntax fr inarp ip dlci-number Undo fr inarp ip dlci-number Fr interface-type Syntax fr interface-type dce dte nni Undo fr interface-type389 Fr iphc Fr lmi n391dteTcp-include Fr map ip , fr compression iphc Fr lmi n392dce Syntax fr lmi n392dce n392-value Undo fr lmi n392dce391 Fr lmi n392dte Syntax fr lmi n392dte n392-value Undo fr lmi n392dte Fr lmi n393dce Fr lmi n393dteSyntax fr lmi n393dce n393-value Undo fr lmi n393dce Syntax fr lmi n393dte n393-value Undo fr lmi n393dte Fr lmi t392dce Syntax fr lmi t392dce t392-value Undo fr lmi t392dce Fr lmi type Fr lmi type ansi nonstandard q933a bi-directionUndo fr lmi type Fr map ip Fr switch Related command interface virtual-templateonUndo fr switch name Fr map ppp Fr switching Syntax fr switching Undo fr switching Interface mfr Interface serial399 Link-protocol fr Link-protocol fr ietf nonstandard Link-protocol fr mfr Mfr bundle-nameSyntax link-protocol fr mfr interface-number Syntax mfr bundle-name name Undo mfr bundle-name Mfr fragment Mfr fragment-sizeSyntax mfr fragment Undo mfr fragment Syntax mfr fragment-size bytes Undo mfr fragment-size Mfr link-name Syntax mfr link-name name Undo mfr link-name name403 Mfr retry Mfr stateup-respond-addlinkSyntax mfr retry number Undo mfr retry Mfr timer ack Syntax mfr timer ack seconds Undo mfr timer ackRelated command mfr timer hello, mfr retry 405 Mfr timer hello Syntax mfr timer hello seconds Undo mfr timer helloMfr window-size Syntax mfr window-size number Undo mfr window-size Reset fr inarp View Frame relay switching viewSyntax reset fr inarp Related command fr inarp Reset fr pvc Related command fr lmi t392dceExample # Clear all the frame relay dynamic address maps X25-template X25 templateSyntax x25-template name Undo x25-template name Syntax x25 template name Undo x25 template name Frame Relay Configuration Commands Garp Configuration Commands Display garp timerSyntax display garp timer interface interface-list Display garp statistics Garp timer Related command garp timer, garp timer leaveallExample # Display Garp timers on port Ethernet 1/0 View Ethernet interface view, port group view Garp timer leaveall Related command display garp timerDependencies of Garp timers Timer Lower limit Upper limit Reset garp statistics Reset garp statistics interface interface-listDisplay gvrp statistics Gvrp Configuration Commands Display gvrp statisticsSyntax display gvrp statistics interface interface-list Related command display gvrp status Display gvrp statusGvrp Syntax gvrp Gvrp registration Gvrp registration fixed forbidden normalUndo gvrp registration Display garp statistics Gvrp Configuration Commands Hdlc Configuration Commands Timer holdTimer hold seconds Link-protocol hdlc Hdlc Configuration Commands Lapb and X.25 Configuration Commands ChannelX25 hunt-group Lapb and X.25 Configuration Commands Description on the fields of the display interface command 423Lapb DCE Display x25 alias-policy Related command x25 alias-policy Example Display x25 cugDisplay x25 hunt-group-info Display x25 cug local-cug local-cug-number network-cug Related command x25 hunt-group Display x25 mapSyntax display x25 map Description on the fields of the display x25 map command Display x25 padExample # Display the X.25 address mapping table Syntax display x25 pad pad-id Display x25 switch-table pvc Display x25 switch-table svcSyntax display x25 switch-table pvc Syntax display x25 switch-table svc dynamic static Related command x25 switch svc Example # Display X.25 SVC static switching tableDisplay x25 vc Syntax display x25 vc lci Data 0/0 Interrupt 0/0 Description on the fields of the display x25 vc command 431SVC Display x25 x2t switch-table Display x25 xot Lapb max-frame Syntax lapb max-frame n1-value Undo lapb max-frame433 Difference between N1 Related command lapb window-size Lapb moduloLapb retry Parameter 8 Modulo Lapb timer Undo lapb timer t1 t2 t3Lapb window-size Syntax lapb window-size k-valueundo lapb window-size Link-protocol lapb Lapb moduloLink-protocol lapb dce dte ip multi-protocol Pad Link-protocol x25 dce dte ietf nonstandard Reset xot Reset Reset lapb statistics Syntax reset lapb statisticsTranslate ip Undo translate ip ip-addressport port-number Translate Undo translate x25 x.121-addressParameter x.121-address X.121 address X25 alias-policy 441 X25 call-facility Description on the user facility option X25 cug-service Related command x25 map, x25 modulo443 Option Description Window-size X25 default-protocol Related command x25 local-cug X25 hunt-group 445 X25 ignore called-address X25 ignore calling-address X25 local-cug 447 Related command x25 call-facility,x25 cug-service X25 mapUndo x25 map ip compressedtcp protocol-address Send-delay delay-time 449Option Description Broadcast Protocols such as Routing Information Protocol X25 modulo Syntax x25 modulo 8 Undo x25 modulo X25 packet-size # Set the modulo on the X.25 interface Serial 2/0 toUndo x25 packet-size 451 X25 pvc Undo x25 pvc pvc-numberDescription on PVC attribute option X25 queue-length Syntax x25 queue-length queue-length Undo x25 queue-length453 Related command x25 window-size X25 receive-threshold X25 response called-address X25 response calling-address455 Related command x25 map X25 reverse-charge-accept X25 switch pvc Related command x25 call-facility,x25 mapUndo x25 switch pvc pvc-number1 X25 roa-list Lapb and X.25 Configuration Commands X25 switch svc 121 mode matching rules459 Input rules of X.121 address mode matching string Number SVC route numberCharacters Input rules X25 switch svc hunt-group 461 X25 switch svc xot Related command display x25 switch-table svc X25 switching Syntax x25 switching Undo x25 switching X25 timer hold X25 timer idleExample # Enable X.25 switching function Syntax x25 timer hold minutes Undo x25 timer hold X25 timer tx0 Syntax x25 timer tx0 seconds Undo x25 timer tx0Related command x25 timer tx1, x25 timer tx2, x25 timer tx3 465 X25 timer tx1 X25 timer tx2Syntax x25 timer tx1 seconds Undo x25 timer tx1 Related command x25 timer tx0, x25 timer tx2, x25 timer tx3 X25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx3Syntax x25 timer tx3 seconds Undo x25 timer tx3 Related command x25 timer tx0, x25 timer tx1, x25 timer tx2 X25 vc-per-map X25 vc-rangeSyntax x25 vc-per-map count Undo x25 vc-per-map X25 window-size Undo x25 window-size469 X25 x121-address X25 xot pvcSyntax x25 x121-address x.121-address Undo x25 x121-address Related command display x25 vc, x25 switching Undo x25 pvc pvc-number1XOT channel parameter option 471 X29 timer inviteclear-time Link Aggregation Configuration Commands Display lacp system-idDisplay link-aggregation interface Syntax display lacp system-id Link Aggregation Configuration Commands Display link-aggregation summary Syntax display link-aggregation summary475 Display link-aggregation verbose Example # Display the link aggregation group summarySyntax display link-aggregation verbose agg-id AL ID 477 Lacp port-priority Lacp system-priority Link-aggregation group descriptionExample # Assign Lacp priority 64 to a port 479 Link-aggregation group mode Related command display link-aggregation verboseRelated command display link-aggregation summary Port link-aggregation group Reset lacp statistics Related command Display link-aggregation verbose ExamplePort-group aggregation Port-group aggregation agg-id Related command display link-aggregation interface Example # Clear statistics about Lacp on all ports Link Aggregation Debugging Commands View User view Default Level 1 Monitor levelDebugging lacp packet Link Aggregation Debugging Commands Device sent an Lacp protocol packet through Ethernet 1/1 Length of the Terminator field in the protocol packet is485 Device received an Lacp protocol packet through Ethernet 1/1 Debugging lacp state 487 Debugging link-aggregation error Syntax debugging link-aggregation error Error Debugging link-aggregation eventSyntax debugging link-aggregation event 489 Aggregation group 10 existed. It contained Ethernet 1/1 # Remove aggregation groupAggregation group 10 was removed Operation key of port Ethernet 1/1 Key 1 was removed Modem Configuration Commands ModemModem auto-answer Modem timer answer Syntax modem timer answer time Undo modem timer answer Sendat command can issue only one AT command at a time SendatWith caution under the guidance of technicians Specifies the communication standard to be adopted Service modem-callback Example # Send dialing command to call numberSyntax service modem-callback 495 Undo service modem-callback Example # Enable the callback function Port Mirroring Configuration Commands Display mirroring-groupMirroring-group Syntax display mirroring-group groupid local Mirroring-group mirroring-port Undo mirroring-group groupid local Mirroring-group monitor-port 499 Mirroring-port # Add POS 5/1 to local port mirroring group Monitor-port # Add Cpos 6/1 to local port mirroring group501 Port Mirroring Configuration Commands PPP and MP Configuration 31 Commands Display interface mp-groupSyntax display interface mp-group mp-number Related command interface virtual-template Display interface virtual-templateSyntax display interface virtual-template number Example # View the information about VT Description on the fields of the display ppp mp command Display ppp mpLink-protocol ppp , ppp mp 505 Display virtual-access For description on the output fields, refer to Table Interface mp-group 507 Interface virtual-template Ip address ppp-negotiate Ppp account-statistics enable Ppp account-statistics enableUndo ppp account-statistics enable Link-protocol ppp Ppp authentication-mode Ppp authentication-mode chap pap call-in domain isp-nameUndo ppp authentication-mode Chap, pap Authentication modes. Use either mode Ppp chap password Related command ppp authentication-modechapPpp chap user Syntax ppp chap user username Related command ppp authentication-mode Ppp ipcp dnsUndo ppp chap user Ppp ipcp dns admit-any Ppp ipcp dns requestSyntax ppp ipcp dns admit-any Undo ppp ipcp dns admit-any Syntax ppp ipcp dns request Undo ppp ipcp dns request Related command remote address Ppp ipcp remote-address forced Ppp lqc Undo ppp lqc515 Ppp mp Ppp mp binding-modeSyntax ppp mp Undo ppp mp Related command Ppp mp user Example Ppp mp max-bindPpp mp max-bind max-bind-num Undo ppp mp max-bind Related command Ppp mp Example Ppp mp min-bindPpp mp min-bind min-bind-num Undo ppp mp min-bind Related command dialer threshold on Ppp mp min-fragmentPpp mp min-fragment size Undo ppp mp min-fragment Ppp mp mp-group Ppp mp userSyntax ppp mp mp-group number Undo ppp mp Example # Add interface Serial 3/0 to MP-group Related command ppp mp and ppp mp max-bind Ppp mp virtual-templateSyntax ppp mp virtual-template number Undo ppp mp 521 Ppp timer negotiate Related command local-useron page 1940, password onSyntax ppp timer negotiate seconds Undo ppp timer negotiate Ppp pap local-user Remote address Undo remote address523 Timer hold PPP Link Efficiency Mechanism Configuration Commands Display ppp compression iphc rtpDisplay ppp compression iphc tcp Display ppp compression stac-lzs Ip tcp vjcompressSyntax ip tcp vjcompress Undo ip tcp vjcompress Ppp compression iphc 527 Ppp compression iphc rtp-connections Ppp compression iphc tcp-connections Ppp compression stac-lzs529 Ppp mp lfi Syntax ppp mp lfi Undo ppp mp lfi Ppp mp lfi delay-per-frag Reset ppp compression iphc531 PPP Link Efficiency Mechanism Configuration Commands Pppoe Server Configuration Commands Display pppoe-server sessionDisplay pppoe-server session all packet Pppoe-server bind Pppoe-server log-information off Pppoe-server max-sessions local-mac Pppoe-server max-sessions remote-mac535 Reset pppoe-server Pppoe-server max-sessions totalPppoe-server max-sessions total number Undo pppoe-server max-sessions total 537 Pppoe Server Configuration Commands Pppoe Client Configuration Commands Display pppoe-client session Pppoe-client dial-bundle-number Reset pppoe-client Related command Reset pppoe-clientReset pppoe-client all dial-bundle-number number Related command pppoe-client Sysname reset pppoe-client all PPP Debugging Commands Debugging ppp Description on the fields of the debugging ppp event command Description on the fields of the debugging ppp ipcp command 545 Description on the fields of the debugging ppp ipcp command LCP moved from the initial state to the starting stateLCP moved from the starting state to the reqsent state 547 PPP Debugging Commands Bridging Configuration Commands Bridge bridge-set enableSyntax bridge bridge-setenable Undo bridge bridge-setenable Bridge aging-time Bridge enable Example # Enable bridge set# Enable IP bridging on bridge set Syntax bridge enable Undo bridge enable Example # Enable bridging Bridge learningBridge mac-address 551 Bridge routing Bridge routing-enable Syntax bridge routing-enable Undo bridge routing-enableBridge-set Syntax bridge-set bridge-set Undo bridge-set bridge-set Display bridge address-table Display bridge information Syntax display bridge information bridge-set bridge-set555 Dynamic S--STATIC Display bridge traffic Display interface bridge-template Syntax display interface bridge-template interface-number557 Fr map bridge Syntax fr map bridge dlci broadcast Undo fr map bridge dlciUP/DOWN Related command display fr map-infoon Bridge routing-enableInterface bridge-template Parameters Related command interface bridge-template Mac-address bridge-template interface viewMap bridge-group Syntax mac-address mac-address Undo mac-address Reset bridge address-table Reset bridge traffic561 X25 map bridge X25 map bridge x121-address x.121-address broadcastUndo x25 map bridge x121-address x.121-address Display x25 map on Isdn Configuration Commands Dialer isdn-leased Isdn BRI interface viewDialer isdn-leased 128k number Undo dialer isdn-leased 128k number Display isdn active-channel Display isdn call-info Example # Display the current state of Isdn interface 2/0 565 Display isdn call-record Display isdn parameters 567 Display isdn spid IsdnKbri Kpri Isdn bch-local-manage 569 Bch-local-manage command on the user side Channels in ascending order by defaultIsdn bch-select-way Isdn caller-number Isdn calling Isdn check-called-numberUndo isdn calling Undo isdn check-called-number check-index Isdn check-time Syntax isdn check-time date-time Undo isdn check-time Isdn crlength Isdn ignore connect-ackUndo isdn crlength Syntax isdn ignore connect-ack Settings must be the same as those on the exchange Isdn ignore hlcUndo isdn ignore connect-ack Isdn ignore hlc Isdn ignore llc Voice calls placed on the BRI interface 1/0Isdn ignore llc Undo isdn ignore llc Configured Isdn ignore sending-completeIsdn ignore sending-complete incoming outgoing Undo isdn ignore sending-complete incoming outgoing Isdn L3-timer Undo isdn L3-timer all timer-nameDescription of Q931 timers Value range Default Timer-name Seconds Isdn link-mode Isdn number-propertySyntax isdn link-mode p2p Undo isdn link-mode View Isdn BRI interface Types and code schemes of Isdn numbers 579Protocol Field Bit value Definition Type Code scheme NTT Qsig Set the type and code scheme of Isdn numbers 581 Isdn overlap-sending Calls Isdn pri-slipwnd-size 583 Isdn protocol-mode Isdn protocol-typeSyntax isdn protocol-type protocol Undo isdn protocol-type Isdn q921-permanent Example # Apply Isdn Etsi on interface BRI 1/0Syntax isdn q921-permanent Undo isdn q921-permanent View Isdn BRI interface view Isdn send-restart Isdn spid autotriggerSyntax isdn send-restart Undo isdn send-restart Syntax isdn spid autotrigger Isdn spid timer Syntax isdn spid timer seconds Undo isdn spid timerIsdn spid nit Syntax isdn spid nit Undo isdn spid nit Isdn spid service Isdn spid service audio data speechUndo isdn spid service Isdn spid resend Isdn spid1Syntax isdn spid resend times Undo isdn spid resend Syntax isdn spid1 spid LDN Isdn spid2 Undo isdn spid1Syntax isdn spid2 spid LDN Undo isdn spid2 Configuration of the Isdn calling command This command applies only on NI-compliant BRI interfacesSpid String of 1 to 20 digits LDN Local dialing number, a string of 1 to 30 digits Isdn two-tei Syntax isdn two-tei Permanent-active Undo isdn two-teiView BRI interface view Syntax permanent-active Undo permanent-active Power-source Syntax power-source Undo power-source # Bring up BRI 2/0 595 Isdn Configuration Commands Mstp Configuration Commands Active region-configurationCheck region-configuration Syntax active region-configuration Display stp Port numberBrief Displays brief information Information Related commands reset stp 599 Display stp abnormal-port Display stp abnormal-portAbnormally blocked ports Root guard action Display stp down-port Display stp historySyntax display stp down-port Syntax display stp instance instance-id history Display stp region-configuration Syntax display stp region-configuration Related commands stp region-configuration Description on the fields of the display stp root commandDisplay stp root Syntax display stp root Display stp tc ModelSent Tree instance, in port name order Instance Region-nameExamples # Map Vlan 2 to MST instance Syntax region-name name Undo region-name Reset stp Reset stp interface interface-listDisplay stp Syntax stp enable disable Undo stp Revision-levelStp Syntax revision-level level Undo revision-level Related commands stp mode Examples # Enable the Mstp feature globally# Disable Mstp on port Ethernet 1/1 Stp bpdu-protection Stp bridge-diameter Stp compliance Stp config-digest-snooping Stp cost Stp edged-port enable disable Or undo stp edged-port enable command to non-edge portStp edged-port Undo stp edged-port Examples # Configure port Ethernet 1/1 as a non-edge port Stp loop-protectionStp max-hops Syntax stp loop-protection Undo stp loop-protection Stp mcheck Syntax stp mcheck Stp mode Stp no-agreement-checkStp mcheck , stp Examples # Enable No Agreement Check on Ethernet 1/1 Stp pathcost-standardView System view Parameters 802.1D-1998 Stp point-to-point 617 Stp port-log Stp port priority 619 Stp priority Stp instance instance-id priority priorityUndo stp instance instance-id priority Stp region-configuration Stp root primary Stp root secondary Stp instance instance-id root secondary Syntax stp tc-protection enable Stp tc-protection disable Stp root-protectionStp tc-protection Syntax stp root-protection Undo stp root-protection Stp timer forward-delay Stp tc-protection threshold Stp timer hello Syntax stp timer hello centi-seconds Undo stp timer hello625 Stp timer max-age Stp timer-factor Syntax stp timer-factor number Undo stp timer-factor627 Stp transmit-limit Vlan-mapping moduloSyntax vlan-mapping modulo modulo Examples # Map VLANs to MSTIs as per the modulo value 629 Mstp Configuration Commands Vlan Configuration Commands Display interface vlan-interfaceSyntax display interface vlan-interface vlan-interface-id Vlan-interface-id Vlan interface ID Vlan interfaces will be displayed# Display the information of VLAN-interface Related command vlan Display vlanExample # Display Vlan 2 information # Display Vlan 3 information Related command display interface vlan-interface Description on the fields of the display vlan commandInterface vlan-interface Example # Create Vlan interface Related command display ip interface on Ip address635 Vlan View Vlan interface view Related command display vlan Example # Enter Vlan 2 view# Create Vlan 4 through Vlan 637 Vlan Configuration Commands PORT-BASED Vlan Configuration Commands Port access vlanSyntax port access vlan vlan-id Undo port access vlan Port Related command port link-type Port hybrid pvid vlanSyntax port hybrid pvid vlan vlan-id Undo port hybrid pvid Port hybrid vlan 641 Port link-type Port trunk permit vlan Port trunk pvid vlan Syntax port trunk pvid vlan vlan-id Undo port trunk pvid643 Related command port link-type Voice Vlan Configuration Commands Voice vlan enable Example Syntax voice vlan vlan-idenableDisplay voice vlan state Voice vlan Undo voice vlan enable Related command display voice vlan stateVoice vlan aging Syntax voice vlan aging minutes Undo voice vlan aging Voice vlan enable Syntax voice vlan enable Undo voice vlan enableVoice vlan mac-address Ffff-f000-0000 Range of 1 to 30 charactersBe a broadcast, multicast or address of all 0s or all fs Display voice vlan oui Example Voice vlan mode auto Voice vlan security enableSyntax voice vlan mode auto Undo voice vlan mode auto Example # Disable the security mode of the voice Vlan 651 Voice Vlan Configuration Commands Port Isolation Configuration Commands Port-isolate enableSyntax port-isolate enable Undo port-isolate enable Display port-isolate group Port Isolation Configuration Commands Dynamic Route Backup Configuration Commands Standby routing-groupStandby routing-rule Standby timer routing-disable Logical Interface Configuration Commands Broadcast-limit linkDisplay interface loopback Syntax display interface loopback number Related command interface loopback Example # View the status of LoopbackSyntax display interface mfr mfr-number Related command interface mfr Example # View the state information about MFR659 LMI Dlci Related command interface mp-group Example # View the state information of MP-group Related command interface null Display interface nullDisplay interface virtual-ethernet Syntax display interface null Related command interface virtual-ethernet Example # View the state information about VEExample # View the state information about VT Description of the fields of the display mfr command 663 Interface, state of the link layer, and the name Interface ethernet 665 Related command display interface loopback Interface loopbackExample # Create Loopback Interface null Example # Create MFRExample # Create MP-group Interface null Related command display interface null Interface virtual-ethernetExample # Enter Null 0 interface view 669 Logical Interface Configuration Commands Cpos Interface Configuration Commands Controller cposSystem view Display controller cpos Display controller cpos cpos-number This table, FRED, COFA, and SEF are alarm errors AERRs Possible error types673 Display controller cpos e1 Some information about T1 channels is omittedSyntax display controller cpos cpos-numbere1 e1-number Display controller cpos t1 Syntax display controller cpos cpos-numbert1 t1-number675 VC-3 Example # Bundle timeslots on E1 channel 677 E1 set clock Related command display controller cpos e1 Example # Enable external payload loopback on E1 channel679 Syntax e1 e1-numbershutdown undo e1 e1-numbershutdown Syntax e1 e1-numberunframed undo e1 e1-numberunframed Undo flag j0 j1 c2 Display controller cposSyntax frame-format sdh sonet undo frame-format Multiplex mode Use the undo loopback command to remove a loopback# Enable external loopback on interface Cpos 1/0 Syntax multiplex mode au-3 au-4 undo multiplex mode Related command frame-format Example # In SDH mode, multiplex AUG to AU-3683 Example # Shut down Cpos physical interface 1/0 Example # Bundle timeslots on T1 channel 685 Related command display controller cpos t1 Example # Enable external loopback on T1 channelSyntax t1 t1-numbershutdown Undo t1 t1-numbershutdown Syntax t1 t1-numberunframed Undo t1 t1-numberunframed 687 Cpos Interface Configuration Commands ARP Configuration Commands Arp check enableSyntax arp check enable Undo arp check enable Arp max-learning-num Arp static Arp timer aging Related command reset arp, display arpRelated command display arp timer aging Display arp Related command arp static, reset arp Description on the fields of the display arp command# Display the number of all ARP entries Display arp timer aging Arp static , and reset arp ExampleDisplay arp timer aging Arp timer aging Naturemask-arp enable Related command arp static and reset arpSyntax naturemask-arp enable Undo naturemask-arp enable Display arp vpn-instance Reset arp Specified by the argument interface-type interface-numberArp static and display arp ARP Configuration Commands Gratuitous ARP Configuration Commands Gratuitous-arp-sending enableGratuitous-arp-learning enable Gratuitous-arp-sending enable Sysname system-view Sysname gratuitous-arp-learning enable ARP Source Suppression Configuration Commands Arp source-suppression enableArp source-suppression limit Display arp source-suppression Related command display arp source-suppression Display arp source-suppressionSyntax display arp source-suppression Description on fields of display arp source-suppression Authorized ARP Configuration Commands Arp authorized enableSyntax arp authorized enable Undo arp authorized enable Arp authorized time-out Authorized ARP Configuration Commands Proxy ARP Configuration Commands Proxy-arp enableLocal-proxy-arp enable Related command display proxy-arp Related command display local-proxy-arp Proxy-arp enableLocal-proxy-arp enable Display proxy-arp Dhcp Server Configuration Commands Bootfile-name Dhcp enableSyntax bootfile-name bootfile-name Undo bootfile-name Syntax dhcp enable Undo dhcp enable Dhcp select server global-pool Dhcp server detectSyntax dhcp server detect Undo dhcp server detect 707 Dhcp server forbidden-ip Dhcp server ip-pool Dhcp server ping timeout Related command dhcp enableDhcp server ping packets Example # Create the Dhcp address pool identified by Dhcp server relay information enable Dhcp update arpSyntax dhcp update arp Undo dhcp update arp Reset dhcp server conflict Display dhcp server conflictDisplay dhcp server expired Display dhcp server conflict all ip ip-address Display dhcp server free-ip Display dhcp server forbidden-ipDisplay dhcp server free-ip Syntax display dhcp server forbidden-ip Reset dhcp server ip-in-use Display dhcp server ip-in-useBinding information of all address pools is displayed Information of Dhcp address pools or an IP address Reset dhcp server statistics Display dhcp server statisticsSyntax display dhcp server statistics Example # Display the statistics on the Dhcp server Display dhcp server tree Display dhcp server tree all pool pool-nameInformation of Dhcp address pools 715 Dns-list Undo dns-list ip-addressall Related command dhcp server ip-pool Domain-nameExpired Gateway-list Netbios-type Related command dhcp server ip-pooland netbios-typeNbns-list 719 Related command dhcp server ip-pooland nbns-list NetworkUndo network Option Undo option code721 Reset dhcp server conflict Reset dhcp server ip-in-useReset dhcp server statistics Related command display dhcp server statistics Static-bind client-identifierExample # Clear the statistics of the Dhcp server 723 Static-bind ip-address Static-bind mac-address Tftp-server domain-name725 Voice-config Undo voice-config as-ip fail-over ncp-ip voice-vlanTftp-server ip-address View Dhcp address pool view 727 Dhcp Server Configuration Commands Dhcp Relay Agent Configuration Commands Dhcp Snooping cannot be configured on the Dhcp relay agentSyntax dhcp relay address-check disable enable Dhcp relay address-check Dhcp relay information enable Dhcp relay information format Dhcp relay information strategy Dhcp relay information strategy drop keep replaceUndo dhcp relay information strategy Dhcp relay release ip Dhcp relay security staticSyntax dhcp relay release ip client-ip Undo dhcp relay security ip-address all dynamic static Related command display dhcp relay security Dhcp relay security tracker733 Dhcp relay server-detect Dhcp relay server-groupDhcp relay server-detect Undo dhcp relay server-detect Related command display dhcp relay server-group Dhcp relay server-select735 Dhcp update arp Dhcp select relayDhcp select relay Undo dhcp select relay Display dhcp relay Display dhcp relay securityServer group that a specified interface corresponds to Groups correlated to an interface or all interfaces Display dhcp relay security statistics Display dhcp relay security trackerDisplay dhcp relay security statistics Information about bindings of Dhcp relay agents Display dhcp relay server-group Display dhcp relay statisticsInterval is 10 seconds Syntax display dhcp relay server-group group-idall Server Client Reset dhcp relay statistics Reset dhcp relay statistics server-group group-idWhich to remove statistics from the relay agent Display dhcp relay statistics Dhcp Relay Agent Configuration Commands Dhcp Client Configuration Commands Description on fields of the display dhcp client command Ip address dhcp-alloc 745 Dhcp Client Configuration Commands Dhcp Snooping Configuration Commands Related command display dhcp-snoopingDhcp-snooping Dhcp-snooping trust Related command display dhcp-snooping trust Display dhcp-snoopingDisplay dhcp-snooping trust Dhcp-snooping Related command dhcp-snooping trust Example Trusted ports# Display information about trusted ports 749 Dhcp Snooping Configuration Commands Bootp Client Configuration Commands Bootp clientDisplay information about Bootp clients on all interfaces Including sub-interfaces and Vlan interfaces Ip address bootp-alloc Syntax ip address bootp-alloc Undo ip address bootp-allocRelated command display bootp client Description on fields of the display bootp client command Dhcp Debugging Commands Debugging dhcp server all error event packetUndo debugging dhcp server all error event packet Debugging dhcp server DHCPmessagetype Dhcp ACK Dhcp NAK Checking for an expired lease DHCP-DISCOVER packet received755 Checking whether the IP address 22.0.0.2 is in use DHCP-REQUEST message received Debugging dhcp relay Sending a DHCP-ACK message Sysname Terminal debugging 759 Debugging dhcp client all error event packet Undo debugging dhcp client all error event packetDebugging dhcp client Then broadcast it 761 State of the Dhcp client is changed from Halt to Init 763 Head Dhcp client starts address conflict detection using ARP ARP message sent DNS Configuration Commands Display dns domainDisplay dns dynamic-host Dns domain Example Display dns proxy table Syntax display dns proxy tableTTL Related command dns server Display dns serverDisplay ip host Syntax display dns server dynamic Dns proxy enable Related command display dns domainSyntax dns proxy enable Undo dns proxy enable Dns domain Dns resolve Dns serverSyntax dns resolve Undo dns resolve Syntax dns server ip-address Undo dns server ip-address Reset dns dynamic-host Related command display dns serverRelated command display ip host Syntax reset dns dynamic-host Related command display dns dynamic-host 771 DNS Configuration Commands IP Accounting Configuration Commands Display ip countDisplay ip count inbound-packets outbound-packets exterior Firewall-denied interior Ip count enable Syntax ip count enable Undo ip count enableDescription on fields of the display ip count rule command Display ip count rule Example # Enable IP accounting Ip count exterior-thresholdIp count firewall-denied 775 Ip count inbound-packets Ip count interior-threshold Example # Count incoming IP packets on Ethernet1/0# Specify not to count incoming IP packets on Ethernet1/0 777 Ip count outbound-packets Ip count rule Ip count timeout Reset ip countSyntax ip count timeout minutes Undo ip count timeout Syntax reset ip count all exterior firewall interior All Clears all statistics Exterior Clears the statistics from the exterior tableInterior Clears the statistics from the interior table # Clear the statistics of all IP packets IP Addressing Configuration Commands Display ip interface Description on fields of the display ip interface command Related command display ip interface Display ip interface briefExample # Display brief information about Ethernet 1/0 783 Displayed Ip address unnumbered 785 IP Addressing Configuration Commands IP Performance Configuration Commands Display fib Description on the fields of the display fib command # Display FIB information passing ACL# Display FIB information passing the IP prefix list abc0 Display fib ip-address Display fib statisticsFor description about the above output, refer to Table Syntax display fib statistics Display icmp statistics Syntax display icmp statisticsExample # Display Icmp statistics Display ip socket 1003072 # Display all socket information Description on the fields of the display ip socket command Display ip statisticsSyntax display ip statistics Display tcp statistics Example # Display statistics of IP packetsSyntax display tcp statistics 793 Related command display tcp status and reset tcp statistics Example # Display statistics of TCP traffic 795 Related command reset udp statistics Display tcp statusDisplay udp statistics Display tcp status Ip forward-broadcast Ip forward-broadcast acl acl-numberUndo ip forward-broadcast Ip redirects enable Ip ttl-expires enable Ip unreachables enable Reset ip statisticsReset tcp statistics Reset udp statistics Tcp anti-naptha enableRelated command display tcp statistics Syntax reset udp statistics Tcp mss Tcp state Tcp syn-cookie enable Related command tcp anti-naptha enableThis support for this command varies with devices Syntax tcp syn-cookie enable Undo tcp syn-cookie enable Tcp timer check-state Tcp timer fin-timeoutExample # Enable the SYN Cookie feature 803 Tcp timer syn-timeout Related command tcp timer syn-timeoutand tcp windowRelated command tcp timer fin-timeoutand tcp window Tcp window Syntax tcp window window-size Undo tcp window805 IP Performance Configuration Commands IP Unicast Policy Routing Configuration Commands Apply default output-interfaceApply ip-address default next-hop View policy-based-route view Parameters ip-address IP address of the default next hop Apply ip-address next-hopUndo apply ip-address next-hop ip-address ip-address Apply ip-precedence Examples # Set the next hop to 1.1.1.1 for matched packetsIP precedences and the corresponding keywords 809 Apply output-interface Display ip policy-based-routeSyntax display ip policy-based-route Display ip policy-based-route setup 811 Local Displays statistics of enabled system policy routing Display ip policy-based-route statisticsInterface-number Routing statistics Related commands if-matchpacket-length Display policy-based-routeIf-match acl Syntax display policy-based-route policy-name Related commands if-match acl If-match packet-lengthIp local policy-based-route Related commands policy-based-route Related commands ip local policy-based-routeIp policy-based-route Policy-based-route Reset policy-based-route statistics Related commands if-match acl and if-matchpacket-lengthSyntax reset policy-based-route statistics policy-name 817 IP Unicast Policy Routing Configuration Commands UDP Helper Configuration Commands Reset udp-helper packetReset udp-helper packet Display udp-helper server Udp-helper enable Syntax udp-helper enable Undo udp-helper enableUdp-helper port Related command display udp-helper server Udp-helper server821 UDP Helper Configuration Commands Urpf Configuration Commands Ip urpf loose strict allow-default-route acl acl-numberIp urpf Undo ip urpf Urpf Configuration Commands Fast Forwarding Commands Display ip fast-forwarding cacheIp fast-forwarding Display ip fast-forwarding cache Fast Forwarding Commands Reset ip fast-forwarding cache Syntax reset ip fast-forwarding cache827 Fast Forwarding Commands IPV6 Basics Configuration Commands Display dns ipv6 dynamic-hostDisplay dns ipv6 server Syntax display dns ipv6 dynamic-host Display ipv6 fib Example # Display IPv6 DNS server informationSyntax display ipv6 fib ipv6-address Description on fields of the display ipv6 fib command Display ipv6 fibcacheDisplay ipv6 host Syntax display ipv6 fibcache Display ipv6 interface Shutdown command 833 Display ipv6 neighbors Display ipv6 neighbors count Static vlan vlan-id count Description on fields of the display ipv6 pathmtu command Display ipv6 pathmtuDisplay ipv6 socket Syntax display ipv6 pathmtu ipv6-addressall dynamic static Description on fields of the display ipv6 socket command Display ipv6 statisticsSyntax display ipv6 statistics 837 Description on fields of the display ipv6 statistics command 839 Display tcp ipv6 statistics Display tcp ipv6 statisticsStatistics # Display the statistics of IPv6 TCP connections 841 Display tcp ipv6 status Syntax display tcp ipv6 status Display udp ipv6 statistics Syntax display udp ipv6 statistics843 TCP6CB Dns server ipv6 Ipv6Syntax ipv6 Undo ipv6 Ipv6 address Ipv6 address auto link-local845 Ipv6 address eui-64 Ipv6 address link-local Ipv6 fibcache Ipv6 fib-loadbalance-type hash-basedSyntax ipv6 fibcache Undo ipv6 fibcache 847 Ipv6 icmp-error Ipv6 host Ipv6 icmpv6 multicast-echo-reply enable Ipv6 mtuSyntax ipv6 mtu mtu-size Undo ipv6 mtu 849 Ipv6 nd autoconfig managed-address-flag Ipv6 nd autoconfig other-flagIpv6 nd autoconfig managed-address-flag Undo ipv6 nd autoconfig managed-address-flag Ipv6 nd dad attempts Ipv6 nd hop-limitSyntax ipv6 nd dad attempts value Undo ipv6 nd dad attempts Syntax ipv6 nd hop-limit value Undo ipv6 nd hop-limit Ipv6 nd ns retrans-timer Ipv6 nd nud reachable-time Ipv6 nd ra halt Syntax ipv6 nd ra halt Undo ipv6 nd ra haltOn a router # Suppress RA messages on Ethernet1/0 853 Ipv6 nd ra interval Ipv6 nd ra prefixUndo ipv6 nd ra interval Undo ipv6 nd ra prefix ipv6-prefix Ipv6 nd ra router-lifetime 855 Ipv6 neighbor Ipv6 neighbors max-learning-num Ipv6 pathmtuUndo ipv6 pathmtu ipv6-address 857 Reset dns ipv6 dynamic-host Related command display ipv6 pathmtuSyntax reset dns ipv6 dynamic-host Ipv6 pathmtu age Reset ipv6 fibcache Reset ipv6 neighborsReset ipv6 pathmtu Reset ipv6 statistics Reset tcp ipv6 statisticsReset udp ipv6 statistics ICMPv6 packets Tcp ipv6 timer fin-timeout Tcp ipv6 timer syn-timeoutExample # Clear the statistics of all UDP packets 861 Tcp ipv6 window Syntax tcp ipv6 window size Undo tcp ipv6 window NAT-PT Configuration Commands Display natpt address-groupDisplay natpt address-mapping Display natpt address-group Display natpt aging-time Syntax display natpt aging-time Example # Display all NAT-PT configuration information Display natpt allDisplay natpt all 865 Display natpt frag-sessions Syntax display natpt frag-sessions Display natpt session Display natpt statisticsSyntax display natpt session all icmp tcp udp Display natpt statistics Natpt address-group Undo natpt address-group group-number Natpt aging-time Natpt enable Syntax natpt enable Undo natpt enableNatpt max-session Syntax natpt max-session max-number Undo natpt max-session Example # Configure a NAT-PT prefix Natpt prefixUndo natpt prefix natpt-prefix 871 Natpt turn-off tos Natpt turn-off traffic-classNatpt turn-off tos Undo natpt turn-off tos Natpt v4bound dynamic Natpt v4bound static873 Natpt v6bound dynamic Reset natpt dynamic-mappings Syntax reset natpt dynamic-mappingsNatpt v6bound static Undo natpt v6bound static ipv6-addressipv4-address Reset natpt statistics Reset natpt statistics# Clear all NAT-PT statistics information Dual Stack Configuration Commands Ipv6 address auto link-local Automatically create a link-local address for an interfaceAutomatically created link-local address Ethernet interface view Example # Configure a link-local address on Ethernet 1/1 879 Dual Stack Configuration Commands Tunneling Configuration Commands Related command interface tunnel and sourceDestination Undo destination Display interface tunnel Syntax display interface tunnel numberExample # Display information of the interface tunnel Display ipv6 interface tunnel Syntax display ipv6 interface tunnel number883 Encapsulation-limit Interface tunnelSyntax encapsulation-limit number Undo encapsulation-limit Syntax interface tunnel number Undo interface tunnel number Example # Create the interface tunnel885 Related command interface tunnel and destination SourceUndo source Tunnel-protocol Ipv4-ipv6Undo tunnel-protocol Tunneling Configuration Commands IPV6 Unicast Policy Routing Configuration Commands Apply destination-based-forwardingView IPv6 policy-based-route view Apply ipv6-address default next-hop Apply ipv6-address next-hop Apply ipv6-precedenceExample # Set a next hop of 11 for matched IPv6 packets Preferences and the corresponding keywords Apply output-interface Display ipv6 config policy-based-route Syntax display ipv6 config policy-based-route policy-nameDisplay ipv6 policy-based-route Display ipv6 policy-based-route Display ipv6 policy-based-route setup Local Displays system policy routing information Related command if-matchpacket-length Display ipv6 policy-based-route statisticsIf-match acl6 Syntax if-match acl6 acl6-number Undo if-match acl6 Related command if-match acl6 Ipv6 local policy-based-routeExample # Permit the packets matching ACL Related command ipv6 local policy-based-route Ipv6 policy-based-route interface viewIpv6 policy-based-route system view 897 IPV6 Unicast Policy Routing Configuration Commands Terminal Access Configuration Commands Auto-closeAuto-link Syntax auto-close time Undo auto-close Bind vpn-instance Syntax bind vpn-instance vpn-name Undo bind vpn-instance Data protect router-unix Data read blockView Terminal template view Syntax data read block Undo data read block Data send delay Syntax data send delay milliseconds Undo data send delayDisplay rta # Display brief information about TTY 903 TTY # Display all the information about terminal access Description on the fields of the display rta all command# Display statistics about terminal 905 # Display terminal access statistics Driverbuf saveDriverbuf size Syntax driverbuf save Undo driverbuf save Idle-timeout Syntax idle-timeout seconds Undo idle-timeoutUndo driverbuf size 907 Related command print information and print menu Menu hotkeyMenu screencode Syntax menu hotkey ascii-code&1-3 Undo menu hotkey Print connection-info Syntax print connection-info Undo print connection-info909 Related command print information Related command print connection-infoand print menuPrint information Print menu Print language RedrawkeyPrint language chinese english Terminal template view Reset rta connection Reset rta statisticsReset rta statistics terminal-number Resetkey Related command display rtaUndo resetkey Rta bind Rta rtc-server listen-port Rta server enable Syntax rta server enable Undo rta server enableRta source-ip Syntax rta source-ip ip-address Undo rta source-ip Rta template Rta terminalHiding TCP connections Sendbuf bufsize Syntax sendbuf bufsize size Undo sendbuf bufsize917 Sendbuf threshold TcpSyntax sendbuf threshold value Undo sendbuf threshold # Disable TCP delay Testkey# Set the TCP send buffer size to 512 bytes Undo testkey Update changed-config AccessUpdate changed-config Values are used for the hotkeys of flow control Vty description Vty hotkeyUndo vty vty-numberdescription 921 Vty password Vty rtc-client remote Vty rtc-server remote923 Related command menu screencode Vty screencodeUndo vty vty-numberscreencode Vty telnet remote Vty tty remoteExample # Set the screen code for VTY 1 to E!9Q 925 Vty-switch priority Vty-switch thresholdSyntax vty-switch priority Undo vty-switch priority Syntax vty-switch threshold times Undo vty-switch threshold 927 Terminal Access Configuration Commands IP Routing Table Commands Bandwidth-based-sharingDisplay ip routing-table Syntax bandwidth-based-sharing Undo bandwidth-based-sharing Special characters for regular expressions String, the end of a string 931 Display ip routing-table acl Syntax display ip routing-table acl acl-number verbose 933 IP Routing Table Commands Display ip routing-table ip-address 935 Display ip routing-table ip-address Display ip routing-table ip-address maskDisplay ip routing-table ip-addresslonger-match Display ip routing-table ip-address mask longer-match 937 Display ip routing-table ip-prefix Display ip routing-table protocol For detailed description of the above output, see Table939 Display ip routing-table statistics # Display summary information about static routesView Any view Display ip relay-route Display ip relay-tunnelDisplay ip relay-route vpn-instance vpn-instance-name # Display recursive route information Display load-sharing ip address Display ipv6 routing-tableExamples # Display recursive tunnel information Syntax display ipv6 routing-table Display ipv6 routing-table acl Syntax display ipv6 routing-table acl acl6-number verbose943 Display ipv6 routing-table ipv6-address Refer to for description about the above outputDisplay ipv6 routing-table ipv6-addressprefix-length Display ipv6 routing-table ipv6-address1 ipv6-address2 945 Display ipv6 routing-table ipv6-prefix Display ipv6 routing-table protocol Display ipv6 routing-table statistics Syntax display ipv6 routing-table statistics# Display routing statistics 947 Display ipv6 routing-table verbose Display ipv6 relay-routeDisplay ipv6 routing-table verbose Entire routing table and information for each route Display ipv6 relay-tunnel Display ipv6 relay-tunnel# Display IPv6 recursive tunnel information 949 Reset load-sharing Load-bandwidthSyntax load-bandwidth bandwidth Undo load-bandwidth Reset ip routing-table statistics protocol Reset ipv6 routing-table statisticsReset ipv6 routing-table statistics protocol all protocol Ripng , or static Sysname reset ipv6 routing-table statistics protocol all BGP Configuration Commands Configuration Commands onAggregate Functions of the keywords If-match clause of the route-policy command Balance BGP/BGP-VPN instance viewSyntax balance number Undo balance Suppress-policy Related commands display bgp routing-table Bestroute as-path-neglect BGP/BGP-VPN instance viewView BGP view/BGP-VPN instance view 955 Comparison is not enabled by default Bestroute compare-med BGP/BGP-VPN instance viewBestroute med-confederation BGP/BGP-VPN instance view Syntax bestroute compare-med Undo bestroute compare-med Bgp Compare-different-as-med BGP/BGP-VPN instance view957 Confederation id Syntax confederation id as-number Undo confederation id Related commands confederation id and confederation peer-as Confederation nonstandardConfederation peer-as View BGP view Dampening BGP/BGP-VPN instance view Undo confederation peer-as as-number-listExamples # Specify confederation peer sub ASs 2000 Undo dampening Default ipv4-unicast Examples # In BGP view, configure BGP route dampeningSyntax default ipv4-unicast Undo default ipv4-unicast 961 Default local-preference BGP/BGP-VPN instance view Default med BGP/BGP-VPN instance viewSyntax default med med-value Undo default med Default-route imported BGP/BGP-VPN instance view Syntax default-route imported Undo default-route imported963 Related commands import-routeBGP/BGP-VPN instance view Description on the fields of the display bgp group commandDisplay bgp group Syntax display bgp group group-name Advertised with the network command Display bgp networkDisplay bgp network # Display routing information that has been advertised Description on the fields of the display bgp paths command Display bgp pathsDisplay bgp peer MED Description on the fields of the display bgp peer command 967 Description on the fields of the display bgp routing command Display bgp routing-table Display bgp routing-table as-path-acl 969 Display bgp routing-table cidr Display bgp routing-table cidr Display bgp routing-table community Display bgp routing-table community-list971 Display bgp routing-table dampened Display bgp routing-table dampenedDampened BGP routes # Display dampened BGP routes Related commands dampening BGP/BGP-VPN instance view Display bgp routing-table dampening parameterDisplay bgp routing-table different-origin-as Display bgp routing-table dampening parameter Display bgp routing-table flap-info Longer-match Related commands display bgp peer Display bgp routing-table peer975 Display bgp routing-table regular-expression Display bgp routing-table statisticEbgp-interface-sensitive Display bgp routing-table statistic Filter-policy export BGP/BGP-VPN instance view Undo ebgp-interface-sensitive977 Filter-policy import BGP/BGP-VPN instance view Graceful-restart timer restart Graceful-restart BGP viewSyntax graceful-restart Undo graceful-restart 979 Graceful-restart timer wait-for-rib Graceful-restart timer wait-for-rib timerUndo graceful-restart timer wait-for-rib Using this command can speed up route convergence Import-route BGP/BGP-VPN instance view 981 Log-peer-change Syntax log-peer-change Undo log-peer-change Network BGP/BGP-VPN instance view 983 Peer advertise-community BGP/BGP-VPN instance view Peer advertise-ext-community BGP/BGP-VPN instance view Related commands display bgp routing-table peer Peer allow-as-loop BGP/BGP-VPN instance view985 Peer as-number BGP/BGP-VPN instance view Peer as-path-acl BGP/BGP-VPN instance viewUndo peer ip-address Peer capability-advertise conventional 987 Peer capability-advertise route-refresh Peer default-route-advertise BGP/BGP-VPN instance view Undo peer group-nameip-address default-route-advertisePeer connect-interface BGP/BGP-VPN instance view Undo peer group-name ip-address connect-interface Peer description BGP/BGP-VPN instance view Peer ebgp-max-hop BGP/BGP-VPN instance view 991 Peer enable BGP view Syntax peer ip-addressenable Undo peer ip-addressenablePeer fake-as BGP/BGP-VPN instance view Related commands peer as-path-aclBGP/BGP-VPN instance view Peer filter-policy BGP/BGP-VPN instance view993 Peer group BGP/BGP-VPN instance view Peer ignore BGP/BGP-VPN instance view Peer ip-prefix995 Peer keep-all-routes BGP/BGP-VPN instance view Peer log-change BGP/BGP-VPN instance view Peer next-hop-local BGP/BGP-VPN instance viewUndo peer group-name ip-address next-hop-local View BGP view /BGP-VPN instance view Peer password # Perform the similar configuration on the peer Peer preferred-value BGP/BGP-VPN instance viewUndo peer group-name ip-address preferred-value 999 Peer public-as-only BGP/BGP-VPN instance view Undo peer group-name ip-address public-as-only Peer reflect-client BGP/BGP-VPN instance view 1001 Peer route-limit BGP/BGP-VPN instance view Peer route-policy BGP/BGP-VPN instance view Peer route-update-interval BGP/BGP-VPN instance view 1003 Peer substitute-as BGP/BGP-VPN instance view Undo peer group-nameip-address substitute-as Peer timer BGP/BGP-VPN instance view Related commands timer BGP/BGP-VPN instance view1005 Preference BGP/BGP-VPN instance view Reflect between-clients BGP viewUndo preference Syntax reflect between-clients Undo reflect between-clients Examples # Disable route reflection between clients Reflector cluster-id BGP viewExamples # Set the cluster ID to 1007 Reset bgp All Resets all BGP connectionsAs-number Resets BGP connections to peers in the AS Refresh bgp Reset bgp dampening Reset bgp flap-info1009 Reset bgp ipv4 all Syntax reset bgp ipv4 allRouter-id Syntax router-id router-id Undo router-id Summary automatic Syntax summary automatic Undo summary automatic1011 Timer BGP/BGP-VPN instance view Syntax timer keepalive keepalive hold holdtime Undo timerSynchronization BGP view Syntax synchronization Undo synchronization Related commands peer timer BGP/BGP-VPN instance view 1013 BGP Configuration Commands BGP Debugging Commands Debugging bgp all BGP configuration information BGP received an Open message from the peer Debugging bgp detail Syntax debugging bgp detail Undo debugging bgp detail1017 Debugging bgp event Route was deleted from the instance BGP has received an Update message Debugging bgp graceful-restartState has changed from Opensent to Openconfirm 1019 BGP neighbor 10.1.1.1 is performing GR BGP peer relationship has been successfully establishedBGP GR Helper received an EOR message from peer Description on the fields of the debugging bgp command Debugging bgp1021 Description on the fields of the debugging bgp open command Information about the sent BGP Open messageAFI/ Safi WTR Information about the received BGP Open message Information about the sent BGP Keepalive messageInformation about the received BGP Keepalive message 1023 Debugging bgp timer ConnectRetry timer for BGP peer 2.2.2.2 expired Hold timer expired on BGP peer Receive Enables the debugging for received BGP packetsSend Enables the debugging for sent BGP packets Update messages Debugging bgp update ipv4 Ip-prefix-name receive send verboseIp-prefix ip-prefix-name receive send verbose Debugging bgp update ipv6 Update messages of IPv4 address family1027 Receive Enables/disables debugging for received BGP packets Send Enables/disables debugging for sent BGP packetsFor IPv6 BGP update messages Complete By default, this debugging is disabled Debugging bgp update l2vpn Update messages of IPv6 address familyVerbose Send verbose Debugging bgp update label-route Update messages in an L2VPN environmentAcl-number ip-prefix ip-prefix-name receive send verbose Receive send verbose Update message information of L3VPN labeled routes 1031 Debugging bgp update peer Update message information of IPv6 labeled routes Debugging bgp update vpls Vpls Update messagesFor BGP Vpls Update messages 1033 Debugging bgp update vpn-instance Information about the sent Vpls update messageInformation about the received Vpls update message Debugging bgp update vpnv4 BGP VPNv4 Update messagesFor BGP VPNv4 Update messages Examples None Update message information of VPNv4 IS-IS Configuration Commands Area-authentication-modeArea-authentication-mode simple md5 password ip osi Undo area-authentication-mode Auto cost enable Syntax auto-cost enable Undo auto-cost enableRelated commands bandwidth-referenceIS-IS view, cost-style Bandwidth-reference IS-IS view Related commands auto cost enable Circuit-cost1039 Related commands isis cost, cost-style Cost-styleRelax-spf-limit Undo cost-style Default-route-advertise IS-IS view Related commands isis cost1041 Description on the fields of the display isis brief command Display isis brief Display isis debug-switches Display isis graceful-restart status Display isis interface Traffic-eng Displays IS-IS traffic engineering informationVerbose Displays IS-IS interface detail information Tunnel Displays IS-IS tunnel information Examples # Display IS-IS enabled interface information # Display detailed IS-IS interface information1045 DIS Display isis license Syntax display isis licenseBFD Display isis lsdb License information varies with device models Display isis mesh-group LspidATT/P/OL # Display the configuration information of IS-IS mesh-group # Configure a static mapping for the remote IS-IS systemDisplay isis name-table Display isis peer Display isis route Up state and direct interface’s IP address# Display detailed IS-IS neighbor information PRI Description on the fields of the display isis route command # Display IS-IS IPv4 routing information1051 Display isis spf-log Display isis statistics Domain-authentication-mode Simple Specifies to send the password in plain textMd5 Specifies to send the password encrypted with MD5 IS-IS view Filter-policy export IS-IS view 1055 Related commands filter-policy import IS-IS view Filter-policy import IS-IS view Related commands filter-policy export IS-IS view Flash-floodLevel-1 level-2 Undo flash-flood level-1 level-2 Graceful-restart IS-IS view Graceful-restart interval IS-IS viewGraceful-restart Graceful-restart suppress-sa Import-route IS-IS viewGraceful-restart suppress-sa Undo graceful-restart suppress-sa Related commands import-route isis level-2 into level-1 Related commands import-routeIS-IS view Import-route isis level-2 into level-1Examples # Redistribute static routes and set the cost to Undo import-route isis level-2 into level-1 Isis authentication-mode Isis This command is not available in loopback interface view Isis circuit-level level-1 level-1-2 level-2Undo isis circuit-level 1063 Related commands is-level Isis circuit-typeSyntax isis circuit-type p2p Undo isis circuit-type Syntax isis dis-name symbolic-name Undo isis dis-name Isis costIsis dis-name 1065 Examples # Configure the name as Localarea for the local LAN Isis dis-priority Isis enable Syntax isis enable process-id Undo isis enableRelated commands isis, network-entity Isis mesh-group Isis peer-ip-ignore Syntax isis peer-ip-ignore Undo isis peer-ip-ignore Isis small-hello Syntax isis silent Undo isis silentSyntax isis small-hello Undo isis small-hello 1069 Isis timer csnp Isis timer hello Isis timer holding-multiplier Isis timer holding-multiplier value level-1 level-2Undo isis timer holding-multiplier level-1 level-2 Isis timer lsp Related commands isis timer helloSyntax isis timer lsp time count count Undo isis timer lsp Related commands isis timer retransmit Isis timer retransmit Related commands Examples Isis timer lspIs-level Syntax is-level level-1 level-1-2 level-2 Undo is-level Related commands isis circuit-level Examples # Configure the router to work in Level-1Is-name Syntax is-name sys-name Undo is-name Is-snmp-traps enable Syntax is-snmp-traps enable Undo is-snmp-trapsIs-name map Undo is-name map sys-id Log-peer-change IS-IS view Lsp-fragments-extend Lsp-length originate 1077 # Restore the default Lsp-length receiveMaximum load-balancing IS-IS view Syntax lsp-length receive size Undo lsp-length receive Related commands Isis, isis enable Examples Network-entityPreference IS-IS view Network-entity net Reset isis all Examples # Clear all IS-IS data structure information Reset isis peer Set-overloadAllow interlevel external Undo set-overload Spf-slice-size Syntax spf-slice-size duration-time Undo spf-slice-size Summary IS-IS view 1083 Timer isp-generation Undo timer lsp-generation level-1 level-2Generation interval Interval Timer lsp-max-age Timer lsp-refreshSyntax timer lsp-max-age seconds Undo timer lsp-max-age Related commands timer lsp-refresh Timer spf Related commands timer lsp-max-ageUndo timer spf Examples # Set the LSP refresh interval to 1500 seconds Virtual-system # Set the maximum SPF calculation interval to 15 secondsUndo virtual-system virtual-system-id 1087 IS-IS Configuration Commands IS-IS Debugging Commands Event Enables IS-IS event debuggingDebugging isis Ha-events interface-information memory-allocating IS-IS Debugging Commands 1091 Snpa Snpa Field CircuitName not enabled 1093 SNP packet length mismatch 1095 Length length Updt Reset Required 1097 Sending pduLevel pduType on circuitName Sending pduLevel Csnp PDU fails 1099 Tent New Distance from RootNodeSourceId 1101 LSP LevelType LSP level, which can be L1 or L2 1103 IP address took effect on the IS-IS interface Router B sent Csnp packets 1105 IS-IS Debugging Commands Ospf Configuration Commands Related commandsL3VPN Configuration Commands on Abr-summary Ospf area view Area Ospf view Asbr-summarySyntax area area-id Undo area area-id Authentication-mode Simple Specifies the simple authentication modeDisplay ospf asbr-summary View Ospf area view Default Related commands ospf authentication-modeSyntax default cost cost limit limit tag tag type type Bandwidth-reference Ospf view Default-cost Ospf area view Undo default cost limit tag typeRelated commands import-route Ospf view Syntax default-cost cost Undo default-cost Default-route-advertise Ospf view Related commands stub Ospf area view, nssaDefault-route-advertise summary cost cost Undo default-route-advertise Description OSPF/OSPF area view Display ospf abr-asbrSyntax description description Undo description # Describe the Ospf area0 as bone area Display ospf asbr-summary Related commands asbr-summary Display ospf briefSyntax display ospf process-id brief Examples # Display Ospf brief information Description on the fields of the display ospf brief command Mpls TE Display ospf cumulative Syntax display ospf process-id cumulative1117 Display ospf error Syntax display ospf process-id errorNssa ASE/NSSA Description on the fields of the display ospf error command 1119 Display ospf interface Display ospf lsdb 1121BDR Description on the fields of the display ospf lsdb command # Display Type2 LSA Network LSA information in the Lsdb Display ospf nexthop Syntax display ospf process-id nexthop1123 LS ID Display ospf peer Description on the fields of the display ospf peer command Display ospf peer statistics# Display brief Ospf neighbor information Syntax display ospf process-id peer statistics Display ospf request-queue Keep neighbor relationship Init Display ospf retrans-queue Examples # Display Ospf request list information1127 Display ospf routing Description on the fields of the display ospf vlink command Display ospf vlinkSyntax display ospf process-id vlink 1129 Enable link-local-signaling Enable logError Enables error logging State Enables state logging Enable out-of-band-resynchronization Filter import/export1131 By default, Summary LSAs filtering is disabled This command is only available on an ABRFilter-policy export Ospf view Undo filter-policy export protocol process-id Examples # Filter redistributed routes using ACL Filter-policy import Ospf viewGraceful-restart Ospf view 1133 Examples # Enable Ietf Graceful Restart for Ospf process # Enable non-IETF Graceful Restart for Ospf processGraceful-restart help Syntax graceful-restart help acl-numberprefix prefix-list Related commands ospf timer dead Graceful-restart interval Ospf viewHost-advertise 1135 Import-route Ospf view Related commands Examples Default-route-advertise Ospf viewImport-route command cannot redistribute default routes 1137 Related commands lsa-generation-interval Lsa-arrival-interval Related commands lsa-arrival-interval Lsa-generation-intervalLsdb-overflow-limit Undo lsa-generation-interval Maximum load-balancing Ospf view Maximum-routesNumber Maximum route number in the range 1 to Related commands ospf Network Ospf area viewNssa 1141 Opaque-capability enable Related commands default-cost Ospf area viewExamples # Configure area1 as an Nssa area Syntax opaque-capability enable Undo opaque-capability Ospf authentication-mode OspfUndo ospf process-id 1143 Related commands authentication-mode Ospf cost Syntax ospf cost value Undo ospf cost1145 Ospf dr-priority Ospf mib-bindingSyntax ospf dr-priority priority Undo ospf dr-priority Syntax ospf mib-binding process-id Undo ospf mib-binding Ospf mtu-enable Ospf network-type Ospf timer dead Related commands ospf dr-priorityThis command is not supported on the Null interface Syntax ospf timer dead seconds Undo ospf timer dead Ospf timer hello Related commands ospf timer helloSyntax ospf timer hello seconds Undo ospf timer hello 1149 Ospf timer poll Ospf timer retransmitSyntax ospf timer poll seconds Undo ospf timer poll Ospf trans-delay Syntax ospf trans-delay seconds Undo ospf trans-delayPeer 1151 Command sets priority for internal routes PreferenceExamples # Specify the neighbor IP address Preference ase route-policy route-policy-name value Reset ospf counters Reset ospf processSyntax reset ospf process-id process 1153 Reset ospf redistribution Syntax reset ospf process-id redistributionRfc1583 compatible Syntax rfc1583 compatible Undo rfc1583 compatible Snmp-agent trap enable ospf Silent-interface Ospf view Ospf Configuration Commands Spf-schedule-interval Stub Ospf area viewUndo spf-schedule-interval Syntax stub no-summary Undo stub Default-cost Ospf area view Stub-routerStub-router Undo stub-router Examples # Enable a stub-router Vlink-peer Ospf area view1159 Related commands authentication-mode,display ospf peer RIP Configuration Commands Default cost RIP viewSyntax default cost value Undo default cost Checkzero Default-route originate Related commands import-route RIP view# Disable default route sending Display rip Description on the fields of the display rip command 1163 Description on fields of the display rip database command Display rip databaseSyntax display rip process-iddatabase X.X/X Display rip interface Display rip route1165 RIP Configuration Commands Description on the fields of the display rip route command Filter-policy export RIP view# Display the routing statistics of RIP process 1167 Filter-policy import RIP view Interface-type interface-number Specifies an interfaceExamples # Reference ACL 2000 to filter outbound routes Host-route Syntax host-route Undo host-route1169 Default cost RIP view Import-route RIP viewIncluding bgp , direct , isis , ospf , rip , rip and static # Set the default cost for redistributed routes to Maximum load-balancing RIP view1171 Syntax peer ip-address Reset rip statistics Syntax reset rip process-idstatisticsRip 1173 Rip authentication-mode Undo rip authentication-mode Mode and parameters By default, an interface is enabled to receive RIP messages# Enable Ethernet1/0 to receive RIP messages Format defined in RFC Related commands rip metricout Related commands rip metricinRip metricin Rip metricout Rip mib-binding Rip outputSyntax rip mib-binding process-id Undo rip mib-binding Syntax rip output Undo rip output Related commands rip input Rip poison-reverseRip split-horizon Examples # Enable the split horizon function on Ethernet1/0 Related commands summaryRip summary-address Rip triggered Rip version Undo rip triggeredRip version 1 2 broadcast multicast Undo rip version Silent-interface RIP view All Silents all interfacesMessages 1181 Timers Related commands rip versionSummary Syntax summary Trip retransmit count 1183 Trip retransmit timer Trip retransmit timer retransmit-time-valueUndo trip retransmit timer Validate-source-address VersionSyntax validate-source-address Undo validate-source-address Version 1 Sysname system-view Sysname rip Sysname-rip-100 version Routing Policy Common Configuration Commands Apply as-pathApply comm-list delete Syntax apply comm-list comm-list-numberdelete Apply community Undo apply comm-list Apply cost Syntax apply cost + value Undo apply costView Routing policy view Parameters + Increases cost value. + Decreases cost value Apply cost-type Apply extcommunity No level is set by default Apply isisApply isis level-1 level-1-2 level-2 Undo apply isis 1191 Related commands route-policy Apply local-preferenceApply mpls-label Syntax apply mpls-label Undo apply mpls-label Apply origin Apply preferenceSyntax apply preference preference Undo apply preference 1193 Apply preferred-value Apply tagSyntax apply tag value Undo apply tag Display ip as-path Syntax display ip as-path as-path-acl numberExamples # Display the information of BGP AS path ACL 1195 Display ip community-list Display ip extcommunity-listSyntax display ip extcommunity-list ext-comm-list-number Display route-policy If-match as-pathSyntax display route-policy route-policy-name Examples # Display the information of routing policy Related commands route-policy,ip as-pathacl Related commands route-policyand ip community-listIf-match community If-match cost If-match extcommunitySyntax if-match cost value Undo if-match cost 1199 If-match interface If-match mpls-label If-match route-type If-match tag Ip as-pathSyntax if-match tag value Undo if-match tag Undo ip as-path as-path-number Ip community-list 1203 Sysname system-view Sysname ip community-list 100 permit Ip extcommunity-list Route-policyUndo ip extcommunity-list ext-comm-list-number 1205 Routing Policy Common Configuration Commands IPV4 Routing Policy Configuration Commands Display ip ip-prefixSyntax display ip ip-prefix ip-prefix-name Related commands ip ip-prefix Examples # Display the statistics of IPv4 prefix list abc Related commands Route-policy Examples If-match ipIf-match ip-prefix Ip ip-prefix Reset ip ip-prefix Syntax reset ip ip-prefix ip-prefix-name1211 IPV4 Routing Policy Configuration Commands IPV6 Routing Policy Configuration Commands Apply ipv6 next-hopDisplay ip ipv6-prefix Syntax display ip ipv6-prefix ipv6-prefix-name If-match ipv6 Next-hop Matches the next hop of IPv6 routing informationString of 1 to 19 characters Address based match criterion for IPv6 routes Ip ipv6-prefix 1215 Reset ip ipv6-prefix Syntax reset ip ipv6-prefix ipv6-prefix-nameExamples # Clear the statistics of IPv6 prefix list abc Static Routing Configuration Commands Delete static-routes allIp route-static Examples # Delete all static routes on the router Configured gateway-address Must be identical to that configured in the NQA test group Ethernet interface and Vlan interfaceAssociate it with a Track entry 1219 Ip route-static default-preference Examples # Set the default preference of static routes to IPV6 BGP Configuration Commands Related commands display ipv6 routing-tableonBalance IPv6 address family view Bestroute as-path-neglect IPv6 address family view Bestroute compare-med IPv6 address family view Bestroute med-confederation IPv6 address family view Compare-different-as-med IPv6 address family view 1223 Dampening IPv6 address family view Default local-preferenceIPv6 address family view Default med IPv6 address family view1225 Default-route imported IPv6 address family view Display bgp ipv6 groupSyntax display bgp ipv6 group ipv6-group-name Display bgp ipv6 network Syntax display bgp ipv6 network1227 Display bgp ipv6 paths Syntax display bgp ipv6 paths as-regular-expression Display bgp ipv6 peer 1229Incomplete Display bgp ipv6 routing-table Field Description Local router ID Display bgp ipv6 routing-table as-path-acl 1231 Display bgp ipv6 routing-table community Examples # Display routes filtered through the AS path ACL Display bgp ipv6 routing-table community-list Display bgp ipv6 routing-table dampenedSyntax display bgp ipv6 routing-table dampened Examples # Display IPv6 BGP dampened routes Display bgp ipv6 routing-table dampening parameter Display bgp ipv6 routing-table different-origin-asSyntax display bgp ipv6 routing-table dampening parameter Syntax display bgp ipv6 routing-table different-origin-as Display bgp ipv6 routing-table flap-info Examples # Display IPv6 BGP routes from different ASsExamples # Display IPv6 BGP route flap statistics 1235 Command Display bgp ipv6 routing-table labelSyntax display bgp ipv6 routing-table label Examples # Display IPv6 BGP label routing information Display bgp ipv6 routing-table peer Display bgp ipv6 routing-table regular-expression1237 Display bgp ipv6 routing-table statistic Filter-policy exportIPv6 address family viewParameters as-regular-expression AS regular expression Syntax display bgp ipv6 routing-table statistic Filter-policy import IPv6 address family view 1239 Group IPv6 address family view Import-route IPv6 address family viewExamples # Reference ACL6 2001 to filter all inbound routes Syntax group ipv6-group-name internal external Ipv6-family Network IPv6 address family viewSyntax ipv6-family Undo ipv6-family 1241 Peer advertise-community IPv6 address family view Peer advertise-ext-community IPv6 address family view Peer allow-as-loop IPv6 address family view1243 Peer as-number IPv6 address family view Peer as-path-acl IPv6 address family view Import export1245 Peer connect-interface IPv6 address family view Peer default-route-advertise Peer description IPv6 address family view1247 Peer ebgp-max-hop IPv6 address family view Peer enable IPv6 address family view Peer fake-as IPv6 address family view1249 Peer filter-policy IPv6 address family view Peer group IPv6 address family view Peer ignore IPv6 address family view1251 Peer ipv6-prefix Peer keep-all-routes IPv6 address family view Peer label-route-capability IPv6 address family view1253 Peer log-change IPv6 address family view Peer next-hop-local IPv6 address family view Peer preferred-value IPv6 address family view 1255 Peer public-as-only IPv6 address family view Peer reflect-client IPv6 address family view Peer route-limit IPv6 address family view 1257 Peer route-update-interval IPv6 address family view Peer route-policy IPv6 address family view Undo peer ipv6-group-nameipv6-address route-update-interval Peer substitute-as IPv6 address family view1259 Peer timer IPv6 address family view Related commands timer IPv6 address family viewPreference IPv6 address family view Reflect between-clients IPv6 address family view 1261 Examples # Enable route reflection between clients Reflector cluster-id IPv6 address family viewRefresh bgp ipv6 Reset bgp ipv6 1263 Reset bgp ipv6 dampening Reset bgp ipv6 flap-info Synchronization IPv6 address family view 1265 Timer IPv6 address family view Related commands peer timer IPv6 address family view 1267 IPV6 BGP Configuration Commands IPV6 IS-IS Configuration Commands # Display detailed IPv6 IS-IS routing information Ipv6 default-route-advertise 1271 Ipv6 enable Syntax ipv6 enable Undo ipv6 enableIpv6 filter-policy export Undo ipv6 filter-policy export protocol process-id Related commands ipv6 filter-policy import Ipv6 filter-policy importUndo ipv6 filter-policy import 1273 Related commands ipv6 filter-policy export Ipv6 import-route Ipv6 import-route isisv6 level-2 into level-1 Undo ipv6 import-route isisv6 level-2 into level-11275 Ipv6 maximum load-balancing Ipv6 preference Ipv6 summary 1277 Isis ipv6 enable Examples # Configure a summary route of 2002/32Syntax isis ipv6 enable process-id Undo isis ipv6 enable IPV6 OSPFV3 Configuration Commands Abr-summary OSPFv3 area viewArea OSPFv3 view Default cost Default-cost OSPFv3 area viewSyntax default-cost value Examples # Enter OSPFv3 Area 0 view Related commands stubOSPFv3 area view Display debugging ospfv3Display debugging ospfv3 Debugging state information Description on the fields of the display isofv3 command Display ospfv3Syntax display ospfv3 process-id Display ospfv3 interface 1283 Display ospfv3 lsdb # Display Link-local LSA information in the Lsdb 1285 Display ospfv3 lsdb statistic Syntax display ospfv3 lsdb statistic Display ospfv3 next-hop Display ospfv3 peerSyntax display ospfv3 process-id next-hop Interface-type interface-number interface type and number Description on the fields of the display isofv3 peer command Display ospfv3 peer statistic Display ospfv3 request-listSyntax display ospfv3 peer statistic Syntax display ospfv3 process-id request-list statistics Display ospfv3 retrans-list # Display the statistics of OSPFv3 link state request listSyntax display ospfv3 process-id retrans-list statistics LS-ID Display ospfv3 routing 1291 # Display the statistics of OSPFv3 routing table Display ospfv3 statistic Display ospfv3 topologySyntax display ospfv3 statistic Syntax display ospfv3 process-id topology area area-id Display ospfv3 vlink Syntax display ospfv3 process-id vlink Filter-policy exportOSPFv3 view 1295 Filter-policy importOSPFv3 view Routes that fail to pass are not added to the routing table Import-routeOSPFv3 view Allow-ibgp direct static cost value type type route-policyDirect static Both Ebgp and Ibgp routes Maximum load-balancingOSPFv3 view Process Related commands router-id Ospfv3Ospfv3 area Undo ospfv3 process-id Ospfv3 cost Ospfv3 dr-priority Ospfv3 timer dead Ospfv3 mtu-ignore1301 Ospfv3 timer hello Related commands ospfv3 timer hello Ospfv3 timer retransmit Ospfv3 trans-delayRelated commands ospfv3 timer dead 1303 Preference ase route-policy route-policy-name preference Related commands Ospfv3 Silent-interfaceOSPFv3 viewRouter-id router-id OSPFv3 processes on a router Spf timers Undo spf timers Related commands default cost Examples # Configure OSPFv3 area 1 as a stub areaUndo vlink-peer router-id hello retransmit trans-delay dead StubOSPFv3 area view IPV6 OSPFV3 Configuration Commands IPV6 Ripng Configuration Commands Default cost RIPng viewSyntax default cost cost Undo default cost View RIPng view Related commands import-route Display ripngSyntax display ripng process-id Description on the fields of the display ripng command Description on fields of the display ripng database commandDisplay ripng database Syntax display ripng process-iddatabase Display ripng interface Display ripng route Syntax display ripng process-idroute1313 Filter-policy export Filter-policy import RIPng view Import-route 1315 Related commands default cost on Maximum load-balancing RIPng view # Restore the default RIPng route priority # Disable RIPng processRipng Undo ripng process-id Ripng default-route Ripng enableSyntax ripng process-idenable Undo ripng enable Related commands ripng metricout Ripng metricinRipng metricout Syntax ripng metricin value Undo ripng metricin Related commands ripng metricin Ripng poison-reverseRipng split-horizon Syntax ripng poison-reverse Undo ripng poison-reverse Information, refer to Frame Relay Configuration Commands on Lapb and X.25 Configuration Commands onRipng summary-address Poison reverse function takes effect Timers 1323 IPV6 Ripng Configuration Commands IPV6 Static Routing Configuration Commands Delete ipv6 static-routes allIpv6 route-static Delete ipv6 static-routes all Sysname system-view Sysname ipv6 route-static 112 24 Multicast Routing Forwarding Configuration Commands Related command multicast boundaryDisplay multicast boundary Display multicast forwarding-table Major values of the flags field 1329MID Value Meaning Related command multicast minimum-ttl Display multicast minimum-ttl Related command display multicast forwarding-table Display multicast routing-table1331 Display multicast routing-table static Description on the fields of display multicast routing-table Display multicast rpf-info 1333 Ip rpf-route-static 1335 Related command display multicast routing-table static Mtracert Description on the fields of the mtracert command Multicast boundary1337 Related command display multicast boundary Multicast forwarding-table downstream-limit Multicast forwarding-table route-limit 1339 Multicast load-splitting Multicast longest-matchSyntax multicast longest-match Undo multicast longest-match View System view, VPN instance view Multicast routing-enable Related command display multicast minimum-ttlMulticast minimum-ttl 1341 Reset multicast forwarding-table # Enable IP multicast routing in VPN instance mvpn Reset multicast routing-table 1343 Sysname reset multicast routing-table Igmp Configuration Commands Display igmp group Description on the fields of the display igmp group command Display igmp interface 1347 Display igmp routing-table Related command igmp fast-leave,last-member-query-interval Fast-leave Igmp viewIgmp Syntax fast-leave group-policy acl-number Undo fast-leave Igmp enable Related command igmp enable, and multicast routing-enableonSyntax igmp enable Undo igmp enable Related command igmp Igmp fast-leave Igmp group-policyUndo igmp group-policy 1351 By default, the last-member query interval is 1 second Igmp last-member-query-intervalIgmp max-response-time Igmp require-router-alert 1353 Robust-count Igmp view , igmp timer query , igmp Igmp robust-countIgmp send-router-alert Igmp interface Igmp static-group Igmp timer other-querier-present Igmp timer query Related command version Igmp view Igmp versionLast-member-query-interval Undo igmp version Max-response-time Igmp view Require-router-alert Igmp viewSyntax require-router-alert Reset igmp group Undo require-router-alertView Public instance Igmp view, VPN instance Igmp view 1359 Related command display igmp group Robust-count Igmp viewSyntax robust-count robust-value Undo robust-count Timer other-querier-present Igmp view Send-router-alert Igmp viewSyntax send-router-alert Undo send-router-alert 1361 Timer query Igmp view Syntax timer query interval Undo timer queryPublic instance Related command igmp version Version Igmp view1363 Igmp Configuration Commands Msdp Configuration Commands Cache-sa-enableDisplay msdp brief Characters Display msdp peer-status 1367 Display msdp sa-cache Related command cache-sa-enable 1369 Display msdp sa-count Encap-data-enable Syntax encap-data-enable Undo encap-data-enableImport-source View Public instance Msdp view, VPN instance Msdp view Related command peer sa-policy Related command display multicast routing-tableonMsdp Originating-rp Peer connect-interfaceUndo originating-rp 1373 Related command static-rpf-peer Related command display msdp peer-statusPeer description Peer mesh-group Peer minimum-ttl Undo peer peer-addressmesh-groupUndo peer peer-addressminimum-ttl 1375 Peer request-sa-enable Peer sa-cache-maximum Import-source command Peer sa-policyFrom the Msdp peer Display msdp peer-status and import-source Reset msdp peer Peer sa-request-policy Reset msdp sa-cache Related command cache-sa-enableand display msdp sa-cache1379 Reset msdp statistics Shutdown Msdp ViewUndo shutdown peer-address Related command display msdp peer-statusand ip prefix-list Example # Configure static RPF peers in the public instanceStatic-rpf-peer Undo static-rpf-peer peer-address Timer retry Syntax timer retry interval Undo timer retry PIM Configuration Commands Auto-rp enableRelated command static-rp PIM view Bsr-policy PIM view Bsr PIM view Undo c-bsr Bsr admin-scope Syntax c-bsr admin-scope Undo c-bsr admin-scopeBsr global 1385 Bsr group Undo c-bsr group group-address Bsr hash-length PIM view Bsr holdtime PIM viewSyntax c-bsr hash-length hash-length Undo c-bsr hash-length Syntax c-bsr holdtime interval Undo c-bsr holdtime Related command c-bsr PIM view and c-bsr interval PIM view Bsr interval PIM viewBsr priority PIM view Bsr PIM view and c-bsr holdtime PIM view Rp PIM view 1389 Related command c-bsr PIM view Rp advertisement-interval PIM viewRp advertisement-interval interval Undo c-rp advertisement-interval Related command c-rp PIM view and c-bsr interval PIM view Rp holdtime PIM viewCrp-policy PIM view Syntax c-rp holdtime interval Undo c-rp holdtime Related command c-bsr PIM view and c-rp PIM view Display pim bsr-info Display pim claimed-route 1393 Display pim control-message counters 1395 BSR Description on the fields of the display pim grafts command Display pim graftsDisplay pim interface 1397 Display pim join-prune PIM DR Display pim neighbor 1399 Interface connecting the PIM neighbor Display pim routing-table 1401 Sysname display pim routing-table Vpn-instance public net Display pim rp-info 1403 Description on the fields of the display pim rp-info command Related command pim hello-optiondr-priority Hello-option dr-priority PIM viewHello-option holdtime PIM view 1405 Hello-option lan-delay PIM view This command is effective for both PIM-DM and PIM-SMRelated command pim hello-option holdtime Hello-option neighbor-tracking PIM view Related command pim hello-optionneighbor-tracking Hello-option override-interval PIM view1407 Holdtime assert PIM view Holdtime join-prune PIM viewSyntax holdtime assert interval Undo holdtime assert Related command jp-queue-size PIM view Jp-pkt-size PIM viewJp-queue-size PIM view Syntax jp-pkt-size packet-size Undo jp-pkt-size Related command multicast routing-enableon PimUndo pim vpn-instance vpn-instance-name Pim bsr-boundary Pim dmBsr PIM view , and multicast boundary on Related command pim sm, ssm-policy PIM view Example # Enable PIM-DM on Ethernet 1/0Related command hello-optiondr-priority PIM view Pim hello-option dr-priority Pim hello-option lan-delay Related command hello-option holdtime PIM viewPim hello-option holdtime 1413 Pim hello-option neighbor-tracking Pim hello-option override-interval Pim holdtime assert Pim holdtime join-prune1415 Pim require-genid Pim smView Interface view Parameter None Pim timer graft-retry Related command pim dmExample # Enable PIM-SM on Ethernet 1/0 Example # Disable state refresh on Ethernet 1/0 Pim timer hello Pim timer join-pruneSyntax pim timer hello interval Undo pim timer hello Related command timer hello PIM view Pim triggered-hello-delay Related command timer join-prune PIM viewProbe-interval PIM view Syntax probe-interval interval Undo probe-interval Register-suppression-timeout PIM view Related command register-suppression-timeout PIM viewSyntax register-suppression-timeout interval Register-policy PIM view Undo register-suppression-timeout Register-whole-checksum PIM viewSyntax register-whole-checksum Undo register-whole-checksum 1421 Reset pim control-message counters Related command state-refresh-interval PIM viewSource-lifetime PIM view Syntax source-lifetime interval Undo source-lifetime Spt-switch-threshold PIM view Undo spt-switch-threshold group-policy acl-numberSource-policy PIM view Syntax source-policy acl-number Undo source-policy PIM Configuration Commands Ssm-policy PIM view State-refresh-interval PIM viewSyntax ssm-policy acl-number Undo ssm-policy 1425 State-refresh-rate-limit PIM view State-refresh-ttl PIM viewSyntax state-refresh-ttl ttl-value Undo state-refresh-ttl By default, the TTL value of state refresh messages is Static-rp PIM viewUndo static-rp rp-address 1427 Timer hello PIM view Timer join-prune PIM viewRelated command display pim rp-infoand auto-rp enable Related command pim timer hello Timer spt-switch PIM view Related command pim timer join-pruneSyntax timer spt-switch interval Undo timer spt-switch Related command spt-switch-threshold PIM view PIM Configuration Commands IPV6 Multicast Routing Forwarding Configuration Commands Related command multicast ipv6 boundaryDisplay multicast ipv6 boundary Display multicast ipv6 forwarding-table IPV6 Multicast Routing and Forwarding Configuration Commands Display multicast ipv6 minimum-hoplimit Values and meanings of the Flags field1433 Related command multicast ipv6 minimum-hoplimit Display multicast ipv6 routing-table Related command display multicast ipv6 forwarding-table Display multicast ipv6 rpf-info1435 Multicast ipv6 boundary Related command display multicast ipv6 boundary Multicast ipv6 forwarding-table downstream-limit1437 Multicast ipv6 forwarding-table route-limit Multicast ipv6 load-splitting Multicast ipv6 longest-match Multicast ipv6 minimum-hoplimit1439 Multicast ipv6 routing-enable Related command display multicast ipv6 minimum-hoplimit Reset multicast ipv6 forwarding-table Reset multicast IPv6 routing-table1441 Sysname reset multicast ipv6 routing-table ff03101 MLD Configuration Commands Display mld group Description on the fields of the display mld group command Display mld interfaceInformation of all interfaces running MLD Display mld routing-table 1445 Fast-leave MLD view Syntax fast-leave group-policy acl6-number Undo fast-leave Last-listener-query-interval Max-response-time MLD viewSyntax max-response-time interval Undo max-response-time 1447 Mld enable Syntax mld enable Undo mld enableMld Syntax mld Related command mld Example # Enable MLD on Ethernet 1/0Mld fast-leave Mld group-policy Mld last-listener-query-interval Mld max-response-time Mld require-router-alert1451 Mld robust-count Syntax mld robust-count robust-value Undo mld robust-count Mld send-router-alert Mld static-groupMld send-router-alert Undo mld send-router-alert Mld timer other-querier-present Mld timer other-querier-present intervalUndo mld timer other-querier-present 125 x 2 + 10 / 2 = 255 seconds Mld timer query Syntax mld timer query interval Undo mld timer queryRelated command mld version Mld version Reset mld group Require-router-alert MLD viewRequire-router-alert Mld require-router-alert and send-router-alert MLD view Related command display mld group Robust-count MLD view# Clear all MLD forwarding entries on Ethernet 1/0 1457 Timer other-querier-present MLD view By default, the MLD querier robustness variable isSend-router-alert MLD view View MLD view Timer query MLD view Related commandTimer query interval Version MLD view Example # Globally set the MLD version to MLDv2 IPV6 PIM Configuration Commands Bsr-policy IPv6 PIM viewBsr IPv6 PIM view Syntax bsr-policy acl6-number Undo bsr-policy Related command c-bsr IPv6 PIM view on Bsr hash-length IPv6 PIM view Example # Set the bootstrap timeout time to 150 seconds Bsr holdtime IPv6 PIM viewBsr interval IPv6 PIM view Syntax c-bsr interval interval Undo c-bsr interval Related command c-bsr IPv6 PIM view Bsr priority IPv6 PIM viewRp IPv6 PIM view Bsr IPv6 PIM view and c-bsr holdtime IPv6 PIM view Rp advertisement-interval IPv6 PIM view View IPv6 PIM view1465 Related command c-rp IPv6 PIM view Example # Set the global C-RP timeout time to 200 secondsRp holdtime IPv6 PIM view Example # Set the global C-RP-Adv interval to 30 seconds Related command c-bsr IPv6 PIM view and c-rp IPv6 PIM view Crp-policy IPv6 PIM viewDisplay pim ipv6 bsr-info Syntax crp-policy acl6-number Undo crp-policy Display pim ipv6 claimed-route Syntax display pim ipv6 claimed-route ipv6-source-address Display pim ipv6 control-message counters BSR Display pim ipv6 grafts Display pim ipv6 interfaceDisplay pim ipv6 grafts Unacknowledged graft messages Interface PIM version PIM mode Display pim ipv6 join-prune PIM-SM and IPv6 PIM-SSM respectivelyTo send on the specified interface Specified IPv6 PIM neighbor Display pim ipv6 neighbor Display pim ipv6 routing-table 1475 Related command display multicast ipv6 routing-tableon Example # View the content of the IPv6 PIM routing table Display pim ipv6 rp-info Syntax display pim ipv6 rp-info ipv6-group-address1477 Embedded-rp Syntax embedded-rp acl6-number Undo embedded-rp acl6-number Related command pim ipv6 hello-optiondr-priority Hello-option dr-priority IPv6 PIM viewHello-option holdtime IPv6 PIM view Example # Set the router priority for DR election to Hello-option lan-delay IPv6 PIM view Related command pim ipv6 hello-option holdtimeExample # Set the prune delay to 200 milliseconds globally Hello-option neighbor-tracking IPv6 PIM view Related command pim ipv6 hello-optionneighbor-tracking Example # Disable join suppression globallyHello-option override-interval IPv6 PIM view Holdtime assert IPv6 PIM view Holdtime join-prune IPv6 PIM view Related command jp-queue-size IPv6 PIM view Jp-pkt-size IPv6 PIM viewJp-queue-size IPv6 PIM view 1483 Related command multicast ipv6 routing-enableon Pim ipv6Pim ipv6 bsr-boundary Syntax pim ipv6 Undo pim ipv6 Related commands pim ipv6 sm, ssm-policy IPv6 PIM view Example # Enable IPv6 PIM-DM on Ethernet 1/0Pim ipv6 dm Syntax pim ipv6 dm Undo pim ipv6 dm Related command hello-optiondr-priority IPv6 PIM view Related command hello-option holdtime IPv6 PIM viewPim ipv6 hello-option dr-priority Pim ipv6 hello-option holdtime Pim ipv6 hello-option lan-delay Pim ipv6 hello-option neighbor-tracking1487 Related command hello-optionneighbor-tracking IPv6 PIM view Example # Disable join suppression on Ethernet 1/0Pim ipv6 hello-option override-interval Pim ipv6 holdtime assert Pim ipv6 holdtime join-prune Pim ipv6 require-genidSyntax pim ipv6 require-genid Undo pim ipv6 require-genid 1489 Pim ipv6 sm Pim ipv6 state-refresh-capablePim ipv6 sm Undo pim ipv6 sm Pim ipv6 timer graft-retry Pim ipv6 timer hello1491 Pim ipv6 timer join-prune Pim ipv6 triggered-hello-delayRelated command timer hello IPv6 PIM view Related command timer join-prune IPv6 PIM view Related command register-suppression-timeout IPv6 PIM view Probe-interval IPv6 PIM viewRegister-policy IPv6 PIM view Example # Set the probe time to 6 seconds Register-suppression-timeout IPv6 PIM view Reset pim ipv6 control-message counters Register-whole-checksum IPv6 PIM view1495 Related command state-refresh-interval IPv6 PIM view Source-lifetime IPv6 PIM viewSource-policy IPv6 PIM view Syntax source-policy acl6-number Undo source-policy Spt-switch-threshold IPv6 PIM view Undo spt-switch-threshold group-policy acl6-number1497 Ssm-policy IPv6 PIM view Syntax ssm-policy acl6-number Undo ssm-policy State-refresh-hoplimit State-refresh-interval IPv6 PIM view1499 State-refresh-rate-limit IPv6 PIM view Static-rp IPv6 PIM viewExample # Set the state refresh interval to 70 seconds Timer hello IPv6 PIM view Related command display pim ipv6 rp-infoUndo static-rp ipv6-rp-address 1501 Timer join-prune IPv6 PIM view Timer spt-switch IPv6 PIM viewRelated command pim ipv6 timer hello Related command pim ipv6 timer join-prune Related command spt-switch-threshold IPv6 PIM view 1503 IPV6 PIM Configuration Commands Multicast VPN Configuration Commands Display multicast-domain vpn-instance switch-group receiveDisplay multicast-domain vpn-instance share-group Count Display multicast-domain vpn-instance switch-group send 1507 Multicast-domain holddown-time Multicast-domain log switch-group-reuse Multicast-domain share-groupView VPN instance view 1509 Multicast-domain switch-delay Multicast-domain switch-group-pool Undo multicast-domain switch-group-pool1511 Sysname system-view Sysname ip vpn-instance mvpn Mpls Basics Configuration Commands Display mpls fast-forwarding cacheDisplay mpls fast-forwarding cache verbose Display mpls ilm Syntax display mpls ilm label include text# Display all ILM entries Related command display mpls statistics interface Display mpls interface1515 Display mpls label Display mpls label label-value1 to label-value2 all Display mpls ldp Display mpls ldp all verbose begin exclude includeMpls ldp system view , mpls ldp interface view Description on the fields of the display mpls ldp command Display mpls ldp cr-lspLSR ID Related command display mpls lsp Display mpls ldp interfaceAll Displays all information 1519 Example # Display information about all LDP interfaces # Display detailed information about all interfaces Display mpls ldp Isp All Displays information about all LSPs established by LDPDest-addr Destination address of the LSP Established by LDP Related command display mpls ldp Display mpls ldp peer Example # Display information about all peers # Display detailed information about all peers1523 Display mpls ldp remote-peer Example # Display information about remote peer BJI Display mpls ldp session 1525 Example # Display information about sessions # Display detailed information about all sessionsLAM MD5 Display mpls ldp vpn-instance 1527 Display mpls lsp Example # Display information about VPN instance vpn1Incoming-interface Incoming interface of the LSPs Outgoing-interface Outgoing interface of the LSPs Exclude Excludes the specified FEC Include Includes the specified FECDest-addr Destination address Asbr Displays information about Asbr established LSPs Description on the fields of the display mpls lsp command Example # Display information about all LSPs# Display detailed information about all LSPs FEC Display mpls lsp statistics Display mpls nhlfeSyntax display mpls lsp statistics Syntax display mpls nhlfe token include text Display mpls route-state # Display all Nhlfe entries Display mpls static-lsp 1533 Display mpls statistics interface Example # Display brief information about static LSPs# Display detailed information about static LSPs Related command statistics interval Example # Display Mpls statistics for all interfaces1535 Display mpls statistics lsp Syntax display mpls statistics lsp index all name lsp-name Example # Display Mpls statistics for all LSPs 1537 Du-readvertise timer Syntax du-readvertise timer value Undo du-readvertise timerDu-readvertise Are both Graceful-restart Mpls LDP view Graceful-restart mpls ldpView Mpls LDP view Syntax graceful-restart mpls ldp Graceful-restart timer neighbor-liveness Graceful-restart timer reconnectRelated commands graceful-restart Mpls LDP view Syntax graceful-restart timer reconnect timer Graceful-restart timer recovery Undo graceful-restart timer reconnect1541 Related command loop-detect,path-vectors Hops-countLabel advertise Syntax hops-count hop-number Undo hops-count Label-distribution Undo label advertiseLabel-distribution independent ordered Undo label-distribution Label-retention Label-retention conservative liberalUndo label-retention Related command hops-count,path-vectors Use the undo lsp-trigger command to restore the defaultLoop-detect Lsp-trigger # Configure the LDP LSR ID of LDP instance named vpn1 Lsr-idSyntax lsr-idlsr-id Undo lsr-id Md5-password MplsSyntax mpls Undo mpls Related command mpls lsr-id # Enable Mpls for interface Ethernet 1/0Mpls ldp system view View System view/interface view # Enable LDP for VPN instance vpn1 Mpls ldp interface viewSyntax mpls ldp Undo mpls ldp 1549 Mpls ldp advertisement Mpls ldp advertisement dod duUndo mpls ldp advertisement Mpls ldp timer hello-hold Related command remote-ipMpls ldp remote-peer Example # Create a remote peer entity named BJI Mpls ldp timer keepalive-hold Mpls ldp transport-address Mpls lsr-idView Interface view/MPLS LDP remote peer view Syntax mpls lsr-id lsr-id Undo mpls lsr-id Mtu-signalling Related command display mpls interfaceSyntax mtu-signalling Undo mtu-signalling Example # Set the LSR ID to Related command loop-detect,hops-count Path-vectorsPing lsp Syntax path-vectors pv-number Undo path-vectors Remote-ip Syntax remote-ip ip-address Undo remote-ip Reset mpls fast-forwarding cache Reset mpls ldpRelated command mpls ldp remote-peer Reset mpls fast-forwarding cache Reset mpls statistics interface Reset mpls statistics lspSyntax reset mpls statistics lsp index all name lsp-name Snmp-agent trap enable mpls Related command display mpls statistics lspStatic-lsp egress Lsp-name Name for the LSP, a string of 1 to 15 characters Static-lsp ingress Undo static-lsp ingress lsp-name Static-lsp transit Undo static-lsp transit lsp-name1561 Related command static-lsp egress, static-lsp ingress Statistics intervalTracert lsp Syntax tracert lsp -a source-ip-exp Ttl expiration pop command Ttl expirationTtl expiration pop Undo ttl expiration pop Ttl propagate Mpls TE Configuration Commands Add hop Delete hop Display explicit-pathSyntax delete hop ip-address Syntax display explicit-path pathname Display isis traffic-eng advertisements # Display the latest TE information advertised by IS-IS TE1567 Intf Addr Display isis traffic-eng link Verbose Displays details1569 Display isis traffic-eng network Vpn-instance vpn-instance-name Specifies a VPN instance. Display isis traffic-eng statistics 1571 Related command te-set-subtlv Display isis traffic-eng sub-tlvs Display mpls rsvp-te Label switched Router ID, Display mpls rsvp-te established Begin include exclude regular-expressionAbout RSVP-TE globally or for an interface # Display RSVP-TE information for interface Ethernet 1/0 Display mpls rsvp-te peer Filters output by regular expressionSpaces Display mpls rsvp-te psb-content 1577 Erhopstrict Display mpls rsvp-te request RSVP-TE requests on the specified or all interfaces1579 X.X Display mpls rsvp-te reservation Display mpls rsvp-te rsb-content 1581LSP ID Tunnel Dest Display mpls rsvp-te sender 1583 Display mpls rsvp-te statistics Global Display global RSVP-TE informationInterface is specified RSVP-TE is displayed # Display the RSVP-TE statistics of interface Serial 1/0 1585 Display mpls static-cr-lsp Ip-address prefix-length arguments Display mpls te cspf tedb # Display detailed information about all static CR-LSPs1587 IGP # Display the Tedb information of IGP area # Display all Tedb information1589 Mpls LSR ID IGP # Display the Tedb information of all nodes # Display Tedb information for a specified interface address Display mpls te link-administration admission-control Links of all interfaces if no interface is specified Display mpls te link-administration bandwidth-allocation Description on fields of the command1593 Display mpls te tunnel Egress ingress remote transit name name incoming-interface # Display detailed information about Mpls TE tunnels 1595LSP-ID Display mpls te tunnel path Lsr-id Ingress LSR ID, in dotted decimal notation# Display the paths that all Mpls TE tunnels traverse Display mpls te tunnel statistics Display mpls te tunnel-interfaceSyntax display mpls te tunnel statistics Syntax display mpls te tunnel-interface CR-LSP Display ospf mpls-te 1599 Area ID TE enabled Ospf area ID LSA Type Display ospf traffic-adjustment Syntax display ospf process-id traffic-adjustment1601 Display tunnel-info Syntax display tunnel-info tunnel-id all statistics# Display statistics about tunnels Enable traffic-adjustment Enable traffic-adjustment advertise# Enable IGP shortcut when the IGP protocol is IS-IS View Ospf view/IS-IS view Explicit-path List hop Modify hop View Explicit path view1605 Mpls rsvp-te authentication Mpls rsvp-te authentication cipher plain auth-keyUndo mpls rsvp-te authentication Mpls rsvp-te Mpls rsvp-te blockade-multiplier 1607 Related command mpls rsvp-te timer refresh Mpls rsvp-te graceful-restartMpls rsvp-te hello Syntax mpls rsvp-te hello Undo mpls rsvp-te hello # Enable Rsvp hello extension on interface Ethernet 1/0 Mpls rsvp-te hello-lost1609 Related command mpls rsvp-te timer hello Mpls rsvp-te keep-multiplierMpls rsvp-te reliability Example # Set the keep multiplier to five Mpls rsvp-te resvconfirm Mpls rsvp-te srefresh Mpls rsvp-te timer graceful-restart recovery Mpls rsvp-te timer graceful-restart restart Mpls rsvp-te timer hello Mpls rsvp-te timer refreshRelated command mpls rsvp-te hello, mpls rsvp-tehello-lost Example # Set the hello interval to five seconds Mpls rsvp-te timer retransmission Related command mpls rsvp-tekeep-multiplierUndo mpls rsvp-te timer retransmission # Enable Mpls TE on interface Ethernet 1/0 Mpls teSyntax mpls te Undo mpls te Related command mpls te link administrative group Mpls te affinity propertyMpls te auto-bandwidth Undo mpls te auto-bandwidth Mpls te backup Related command mpls te timer auto-bandwidthMpls te backup hot-standby ordinary Undo mpls te backup Mpls te backup bandwidth With backup enabled, the record routeExample # Enable hot backup on tunnel Mpls te bandwidth Mpls te bandwidth change thresholdsMpls te bandwidth bc0 bc1 bandwidth Undo mpls te bandwidth Mpls te commit Syntax mpls te commitView Tunnel interface view Mpls te cspf timer failed-link Related command mpls te cspfExample # Set the failed link timer to 50 seconds Mpls te cspf Mpls te fast-reroute Mpls te fast-reroute bypass-tunnelSyntax mpls te fast-reroute Undo mpls te fast-reroute Mpls te igp advertise Description Example# Set the hold time to 10000 milliseconds 1623 Mpls te igp metric Mpls te igp shortcutMpls te igp shortcut isis ospf Undo mpls te igp shortcut Mpls te link administrative group Related command mpls te affinity propertyMpls te loop-detection Syntax mpls te loop-detection Undo mpls te loop-detection Mpls te max-link-bandwidth Mpls te max-reservable-bandwidth Related command mpls te path metric-type Mpls te metricUndo mpls te max-reservable-bandwidth Syntax mpls te metric value Undo mpls te metric Related command mpls te metric Mpls te path explicit-pathMpls te path metric-type Example In Mpls view Mpls te priority Mpls te record-routeUndo mpls te priority Syntax mpls te record-route label Undo mpls te record-route Mpls te reoptimization user view Mpls te reoptimization tunnel interface viewMpls te reoptimization Mpls te resv-style Mpls te retry Related command mpls te timer retry Example # Set the maximum number of tunnel setup retries toExample # Enable route pinning Mpls te route-pinning Mpls te signal-protocol Mpls te signal-protocol crldp rsvp-te staticMpls te tie-breaking Mpls te tie-breaking least-fill most-fill random Mpls te timer auto-bandwidth By default, automatic bandwidth adjustment is disabledRelated command mpls te auto-bandwidth Mpls te timer fast-reroute Mpls te timer retrySyntax mpls te timer retry second Undo mpls te timer retry 1635 Related command mpls te retry Examples # Configure the tunnel ID asMpls te tunnel-id Mpls te vpn-binding Mpls-te enable Syntax mpls-te enable Undo mpls-teRelated command opaque-capability Next hop Related command delete hop Opaque-capability Reset mpls rsvp-te statistics Reset mpls te auto-bandwidth adjustment timersSyntax reset mpls te auto-bandwidth adjustment timers Static-cr-lsp egress Static-cr-lsp ingress Static-cr-lsp transit CR-LSP on the ingress or a transit nodeUndo static-cr-lsp transit tunnel-name Use the undo te-set-subtlvcommand to restore the default # Configure sub-TLVs for IS-IS processBw-constraint Sets the bandwidth constraint sub-TLV Value Sub-TLV in the range 19 to If no level is specified, IS-IS TE applies to Level-1-2 Cost-style on Mpls TE Configuration Commands Mpls L2VPN Configuration Ccc interface in-label out-label Ccc interface out-interface Undo ce ce-name Connection # Create a CE named ce2 for a VPNView Mpls L2VPN CE view 1647 Related command route-distinguisher Mpls L2VPN view Display bgp l2vpnTunnel select-seq load-balance-number on 1649 CE ID Verbose Peer Local 1651 Pref Preference Display ccc Syntax display ccc ccc-name ccc-nametype local remote# Display information about all local CCC connections # Display information about all CCC connections Display l2vpn ccc-interface vc-type Down Configured on the router Configured on the CE interfaceDisplay mpls l2vc 1655 VC ID VC ID Display mpls l2vpn Vpn-name local-ce remote-ce Description on the fields of the display mpls l2vpn command # Display information about L2VPN vpn1# Display information about local CEs of L2VPN vpn1 Display mpls l2vpn connection # Display information about remote CEs of L2VPN vpn11659 Status Status of the connection Peer-id Description on the fields of mpls l2vpn connection summary Display mpls l2vpn forwarding-info Display mpls static-l2vcExample # Display Mpls L2VPN forwarding information L2vpn-family Syntax l2vpn-family1663 Related command tunnel select-seqload-balance-numberon Mpls l2vcUndo l2vpn-family Mpls l2vpn Mpls l2vpn vpn-nameExample # Create a Martini Mpls L2VPN connection Syntax mpls l2vpn Undo mpls l2vpn Mpls static-l2vc destination # Create Kompella VPN named vpn2 and enter Mpls L2VPN viewUndo mpls static-l2vc Reset bgp l2vpn Mtu Mpls L2VPN viewSyntax mtu mtu Example # Set the MTU for Kompella connections to Re-create the VPN using the new RD Takes effect only when it is configured with an RDRoute-distinguisher Mpls L2VPN view Route-distinguisher route-distinguisher Vpn-target Mpls L2VPN view Example # Associate VPN vpn1 with VPN targets1669 Mpls L2VPN Configuration Commands Apply access-vpn vpn-instance Default local-preference BGP-VPNv4 subaddress family viewSyntax default local-preference value View Policy routing view Default med BGP-VPNv4 subaddress family view Description VPN instance view Display bgp vpnv4 all routing-table1673 Example # Display all BGP VPNv4 routing information Display bgp vpnv4 group All Specifies all VPNv4 peers1675 Display bgp vpnv4 network Display bgp vpnv4 paths Display bgp vpnv4 all vpn-instance vpn-instance-name pathsBe displayed # Display all BGP VPNv4 AS path information Display bgp vpnv4 peer Verbose Displays detailed informationVPNv4 peers 1679 # Display all BGP VPNv4 peer information # Display detailed information about BGP VPNv4 peer 1681 Display bgp vpnv4 route-distinguisher routing-table Related command route-distinguisher VPN instance view Example # Display the BGP VPNv4 routing information of RD1683 Fields of the above output Display bgp vpnv4 routing-table label All Specifies all VPNv4 peers1685 Display bgp vpnv4 vpn-instance routing-table 1687 Display fib statistics vpn-instance Display fib vpn-instanceDisplay fib statistics vpn-instance Display fib vpn-instance vpn-instance-name include string Display ip vpn-instance # Display detailed information about a VPN instance1689 Related command sham-link Display ospf sham-linkSyntax display ospf process-id sham-link area area-id Example # Display information about all Ospf sham links Display tunnel-policy # Display information about Ospf sham links in areaDisplay tunnel-policy all policy-name tunnel-policy-name Tunneling policy or all tunneling policies Example # Configure the Ospf domain ID Domain-id# Display tunneling policy aaa Export route-policy Filter-policy export BGP-VPNv4 subaddress family view1693 Filter-policy import BGP-VPNv4 subaddress family view Import route-policy Ip binding vpn-instance1695 Ip vpn-instance Ipv4-familyView BGP view Vpnv4 Enters BGP-VPNv4 subaddress family view Peer advertise-community BGP-VPNv4 subaddress family view 1697 Peer allow-as-loop Peer as-path-acl BGP-VPNv4 subaddress family view Peer default-route-advertise vpn-instance 1699 Peer enable Related command peer upePeer filter-policy BGP-VPNv4 subaddress family view Peer group 1701 Peer ip-prefix BGP-VPNv4 subaddress family view Peer label-route-capability BGP view/BGP VPN instance view Peer next-hop-invariable BGP-VPNv4 subaddress family view 1703 Peer next-hop-local Peer public-as-only BGP-VPNv4 subaddress family view Peer reflect-client 1705 Peer route-policy BGP-VPNv4 subaddress family view Peer upe Command applies to inter-provider VPN option B schemes Policy vpn-targetSyntax policy vpn-target Undo policy vpn-target 1707 Reflect between-clients Reflector culster-id Refresh bgp vpn-instance 1709 Reset bgp vpn-instance Refresh bgp vpnv4 Reset bgp vpn-instance dampening Reset bgp vpn-instance flap-info1711 Reset bgp vpnv4 Route-distinguisher VPN instance viewSyntax route-distinguisher route-distinguisher Then re-create the VPN instance and re-configure a new RD Route-tagInstance Syntax route-tag tag-value Undo route-tag Example # Configure the route tag for Ospf process 100 as Routing-table limitImport-route Ospf view on Rr-filter Sham-linkUndo rr-filter View Ospf area view Mpls L3VPN Configuration Commands Related command tunnel select-seqload-balance-number Tnl-policy VPN instance viewTunnel-policy Undo tnl-policy Load-balance-number command can be used Tunnel select-seq load-balance-numberUndo tunnel select-seq Vpn-instance-capability simple Vpn-target VPN instance viewView Ospf multi-instance view 1719 Mpls L3VPN Configuration Commands VAM Server Configuration Commands Authentication-algorithmAuthentication-method Vam server vpn , authentication-method Vam server vpn , authentication-algorithm Display vam server address-map Display vam server statistic Syntax display vam server statistic all vpn vpn-nameDescription on the fields of display vam server address-map 1723 Example # Display statistics of the VAM server # Display statistics of VPN domain 1 on the VAM server Related command vam server vpn Encryption-algorithmHub private-ip Undo hub private-ip private-ip-address Related command vam server vpn, keepalive retry Keepalive interval Related command vam server vpn, keepalive interval Keepalive retryPre-shared-key VPN domain view Syntax keepalive retry retry-times Undo keepalive retry Server enable Syntax server enable Undo server enableRelated command vam server vpn, vam server enable Example # Enable the VAM server function of VPN domain Vam server enable Related command Vam server vpn, server enable ExampleVam server ip-address Vam server vpn Syntax vam server vpn vpn-name Undo vam server vpn vpn-name VAM Client Configuration Commands Client enableRelated command vam client name, and vam client enable 100 Example # Display the status information of VAM client abc Pre-shared-key VAM client view Pre-shared-key cipher simple key-stringVAM client view Cipher Specifies a pre-shared key in cipher text No pre-shared key is configured by default Related command vam client nameResend interval Syntax resend interval time-interval Undo resend interval Server primary ip-address Server secondary ip-address1735 Vam client enable By default, no local username or password is configuredExample # Set the local username and password both to user User Vam client name and client enable By default, no VAM client is configuredVam client name An interface Vpn Undo vpnExample # Specify the VAM client abc to belong to VPN Ipsec Profile Configuration Commands Related command ipsec profile system view101 Display ipsec profile Inbound ESP setting Ipsec profile system view 1741 Ipsec Profile Configuration Commands Dvpn Tunnel Configuration Commands 102Display dvpn session Associated with the VAM client Dvpn session dumb-time Dumb Dvpn session idle-time Ipsec profile tunnel interface viewUndo ipsec profile ipsec-profile-name&1-6 1745 Keepalive Undo keepalive Related command Interface tunnel on Example Tunnel-protocol dvpn udpSyntax tunnel-protocol dvpn udp Undo tunnel-protocol Related command interface tunnel on Example # Configure the Dvpn tunnel modeVam client Syntax vam client client-name Undo vam client GRE Configuration Commands Related command interface tunneland source103 Example # Display information about interface Tunnel0 Down 1751 Gre checksum Syntax gre checksum Undo gre checksum Related command interface tunnel Gre keyUndo gre key 1753 Syntax interface tunnel number Undo interface tunnel number 1755 Tunnel-protocol gre Syntax tunnel-protocol gre ipv6 Undo tunnel-protocol L2TP Configuration Commands 104Allow l2tp Undo allow Related command l2tp-group Related command Display l2tp tunnel ExampleDisplay l2tp session Sessions Display l2tp tunnel Syntax display l2tp tunnel1759 L2tp enable L2tp sendaccm enableRelated command allow l2tp Syntax l2tp enable Undo l2tp enable L2tpmoreexam enable L2tp enableUse the undo l2tp-group command to remove an L2TP group L2tp-group Related command allow l2tp and start l2tp Related command Mandatory-lcp ExampleMandatory-chap Mandatory-lcp Reset l2tp tunnel Related command mandatory-chapUndo mandatory-lcp View L2TP group view Tunnel authentication Related command display l2tp tunnelSyntax tunnel authentication Start l2tp Undo tunnel authentication Tunnel avp-hiddenSyntax tunnel avp-hidden Undo tunnel avp-hidden 1765 Tunnel flow-control Tunnel name Tunnel password Tunnel timer hello L2TP Configuration Commands Traffic Policing TP Configuration Commands Description on the fields of the display qos car commandDisplay qos car interface Filed Description Description on the fields of the display qos carl command Display qos carlQos car Display qos carl carl-index 1771 Qos carl Undo qos carl carl-index Examples # Configure Carl rule 1 with packet precedence 1773 Traffic Policing TP Configuration Commands Traffic Shaping Configuration Commands Description on the fields of the display qos gts command106 Display qos gts interface Qos gts Undo qos gts any acl acl-number queue queue-number Related commands acl on 1777 Traffic Shaping Configuration Commands Line Rate Configuration Commands Description on the fields of the display qos lr command107 Display qos lr interface Qos lr interface view Qos lr layer 2 interface view or port group viewUndo qos lr inbound outbound Layer 2 module interface view, port group view Interfaces is 4 or 9, this argument is not supported1781 Line Rate Configuration Commands Defining Class Commands 108Display traffic classifier If-match Undo if-match not match-criteriaClass view Match-criteria Class match rules. The values are as follow 1785 Value Description Rtp start-portEnd-port Qos-local-id Define Mpls EXP precedence matching rule Related commands traffic classifier # Define a class to match ACL1787 # Define a class to match the ACL named flow # Define a class to match IPV6 ACL# Define a class to match the IPv6 ACL named flow # Define matching rule for all packets Traffic classifier Traffic classifier tcl-name operator and orUndo traffic classifier tcl-name By default, the relation is operator Examples # Define a class named as class1 Defining Traffic Behavior Commands 109Car Undo car Display traffic behavior Qos policy , traffic behavior , classifier behavior Filter GtsFilter deny permit Undo filter Redirect Undo gtsUndo redirect View Traffic behavior view Remark atm-clp Syntax remark atm-clp atm-clp-value Undo remark atm-clp1795 Remark dot1p Remark dscpSyntax remark dot1p 8021p Undo remark dot1p Syntax remark dscp dscp-value Undo remark dscp Remark fr-de Syntax remark fr-de fr-de-value Undo remark fr-de1797 Remark ip-precedence Remark mpls-expExamples # Remark the DE bit in FR packets to Syntax remark mpls-exp exp-value Undo remark mpls-exp Remark qos-local-id Traffic behavior1799 Examples # Define a traffic behavior named behavior1 Defining Policy Commands Related commands qos policy110 Classifier behavior Description on the fields of the display qos policy command System-defined Policy pre-defined by the systemUser-defined Policy pre-defined by the user Tcl-name Class name in the policy Display qos policy interface 1803 Qos apply policy interface view EXP Qos apply policy layer 2 interface view or port group view 1805 Qos policy Syntax qos policy policy-name Undo qos policy policy-name 1807 Defining Policy Commands Fifo Queuing Configuration Commands 111Qos fifo queue-length 1809 Fifo Queuing Configuration Commands PQ Configuration Commands Related commands qos pq112 Display qos pq interface Related commands qos pq, qos pq pql Qos pqExamples # Display PQLs Syntax qos pq pql pql-index Undo qos pq Qos pql default-queue Qos pql inbound-interfaceExamples # Apply the priority list 12 to the Ethernet 1/0 1813 By default, no classification rule is configured Qos pql protocolDescription on values of queue-key and key-value Queue-key Key-value Description Qos pql queue 1815 PQ Configuration Commands CQ Configuration Commands Related commands qos cq113 Display qos cq interface Default values will not be displayed Qos cqExamples # Display information about a CQL Syntax qos cq cql cql-index Undo qos cq Qos cql default-queue Examples # Assign default queue 2 to CQLQos cql inbound-interface 1819 Qos cql protocol Descriptions of values of queue-key and key-value Qos cql queue 1821 Qos cql queue serving Undo qos cql cql-indexqueue queue-numberservingExamples # Specify byte-count of queue 2 in the CQL 5 to WFQ Configuration Commands Related commands qos wfq114 Display qos wfq interface Qos wfq Undo qos wfqDisplay interface, display qos wfq interface CBQ Configuration Commands 115Display qos cbq interface Qos max-bandwidth Queue af Queue ef 1827 Queue wfq Queue-length WredSyntax wred dscp ip-precedence Undo wred 1829 Wred dscp Undo wred dscp dscp-value Wred ip-precedence 1831 Wred weighting-constant RTP Priority Queue Configuration Commands Description on the fields of the display qos rtpq command116 Display qos rtpq interface Qos rtpq Qos rtpq Related commands qos reserved-bandwidth 1835 RTP Priority Queue Configuration Commands QOS Token Configuration Commands 117Qos qmtoken Qos qmtoken token-number QOS Token Configuration Commands Priority Mapping Table Configuration Commands Related commands qos map-tabledot1p-Ip118 Display qos map-table Related commands display qos map-table Parameters in the default mapping tableQos map-table dot1p-Ip Import 1841 Priority Mapping Table Configuration Commands Port Priority Configuration Commands 119Qos priority Undo qos priority Port Priority Configuration Commands Port Priority Trust Mode Configuration Commands 120Display qos trust interface Qos trust Port Priority Trust Mode Configuration Commands Wred Configuration Commands 121Display qos wred interface 1847 Qos wred enable Qos wred dscp ip-precedence enableUndo qos wred enable Dscp Uses the Dscp value for calculating drop probability By default, the dropping method of a queue is tail drop Related commands qos wfq, display qos wred interfaceQos wred dscp 1849 Qos wred weighting-constant Discard-probability discard-probUndo qos wred ip-precedence ip-precedence Length, in the range 1 to 16. It defaults to Wred with the qos wred enable command on itQos wred enable, display qos wred interface Calculate the average length of Wred queues Wred Configuration Commands Wred Table Configuration Commands 122Display qos wred table Syntax display qos wred table table-name Qos wfq , qos wred enable , display qos wred interface Qos wred queue tableQos wred apply Related commands qos wred queue table in system view Queue1855 Wred Table Configuration Commands Mpls QOS Configuration Commands 123If-match mpls-exp Qos cql protocol mpls exp Related commands qos cql protocol Qos pql protocol mpls exp Related commands qos pql protocol Examples # Set EXP value of remarked Mpls packet to1859 Mpls QOS Configuration Commands DAR Configuration Commands 124Dar max-session-count Dar protocol Protocols of pre-defined ports Protocol name Protocol type Pre-defined port number 1863 # Restore the default name of the user-defined01 protocol Dar protocol-renameDar protocol-statistic Undo dar protocol-rename user-defined-name Display dar information Undo dar protocol-statisticSyntax display dar information 1865 Display dar protocol Display dar protocol all protocol-name 1867 Display dar protocol-rename Display dar protocol-rename Display dar protocol-statistic If-match protocol If-match protocol http Reset dar protocol-statistic If-match protocol rtpUndo if-match not protocol rtp payload-type audio video Information, i.e. to restore the statistics to Reset dar sessionAll Deletes all statistics information # Deletes all statistics information DAR Configuration Commands FR QOS Configuration Commands 125Apply policy outbound # Define a traffic behavior named behavior Related commands ebs, cir allow, cir CbsCir Undo cir Related commands Cir allowCbs, ebs, cir allow Cir allow inbound outbound committed-information-rate Related commands cbs, ebs, cir Related commands fr congestion-thresholdCongestion-threshold Undo cq Related commands wfq, pq, fr pvc-pq Display fr class-map1879 Related commands fragment Display fr fragment-info # Display FR fragment information of a certain interfaces 1881 Display fr switch-table Fr switch 1883 Display qos pvc-pq interface PVC PQ on FR interface# Display PVC PQ information on FR interface Serial2/0 Related commands Cbs, cir allow, cir Examples EbsFifo queue-length Related commands fr class Related commands fr-classFr class Fr congestion-threshold Related commands congestion-threshold Fr de del1887 Related commands fr del inbound-interface,fr del protocol Related commands fr de del, fr del protocolFr del inbound-interface Related commands fr de del, fr del inbound-interface Fr del protocolProtocol ip IP 1889 Related commands pvc-pq Fr pvc-pqUndo fr pvc-pq Related commands fr class, fr-class,fr dlci Fr traffic-policingFr traffic-shaping Syntax fr traffic-policing Undo fr traffic-policing Examples # Enable Frts on the serial interface Serial 1/0 FragmentFr-class Undo fragment fragment-size Related commands fr class, fr dlci Related commands cq, wfq, fr pvc-pqPvc-pq Undo pq Rtpq Undo pvc-pqFr pvc-pq Number, in the range 2000 to Related commands fr traffic-shaping,cir allow, and cir Traffic-shaping adaptationUndo traffic-shaping adaptation becn interface-congestion Related commands cq, pq, fr pvc-pq WfqUndo wfq Examples # Apply WFQ to the FR class test1 802.1X Configuration Commands Example # Display 802.1x configuration information126 Display dot1x Descriptions on the fields of the display dot1x command Dot1x Dot1x interface interface-listUndo dot1x interface interface-list Dot1x Dot1x authentication-method Related command display dot1x# Enable 802.1x globally Syntax dot1x authentication-method chap eap pap Undo dot1x authentication-method Dot1x guest-vlan Dot1x guest-vlan vlan-id Undo dot1x guest-vlan Dot1x handshake Dot1x handshakeUndo dot1x handshake Dot1x max-user Undo dot1x max-user interface interface-listDot1x max-user user-number Undo dot1x max-user By default, the multicast trigger function is enabled Dot1x multicast-triggerDot1x port-control Dot1x port-method Dot1x port-method macbased portbased Undo dot1x port-method Dot1x quiet-period Syntax dot1x quiet-period Undo dot1x quiet-period1907 Related command display dot1x, dot1x timer Dot1x retryDot1x supp-proxy-check Undo dot1x retry 1909 Dot1x timer Reset dot1x statistics Example # Set the server timeout timer to 150 secondsReset dot1x statistics interface interface-list 1911 Example # Clear 802.1x statistics on port Ethernet 1/1 AAA Configuration Commands Access-limitAccounting default 127 AAA Configuration Commands Accounting lan-access Accounting loginRelated command accounting default, radius scheme 1915 Undo accounting login Accounting optionalSyntax accounting optional Undo accounting optional Accounting portal 1917 Accounting ppp Related command domain, radius scheme Undo attribute access-limit idle-cut ip location mac vlanAccounting voip Attribute Authentication default Related command display local-userLocal Performs local authentication Example # Set the IP address of local user user1 to Authentication lan-access Undo authentication lan-accessLocal Performs local authentication None Does not perform any authentication Authentication login Related command authentication default, radius scheme Authentication portal 1923 Authentication ppp Undo authentication pppRadius-scheme radius-scheme-name local Authentication voip Authorization command1925 Authorization default Related command authorization default, hwtacacs scheme Authorization lan-access 1927 Authorization login Related command authorization default, radius scheme Authorization portal 1929 Authorization ppp Authorization voipUndo authorization ppp Authorization default , hwtacacs scheme , radius scheme Cut connection Domain , radius scheme Display connection Related command cut connection Example Description on the fields of the display connection commandDisplay domain # Display information about all AAA user connections Related command access-limit,domain, state Description on the fields of the display domain command Related command local-user Display local-user Domain # Display information about all local usersUndo domain isp-name Description on the fields of display local-user Domain default Related command access-limit,state, display domainDomain default disable enable isp-name State , display domain Idle-cut Ip poolDomain Domain aabbcc.net Related command remote address on LevelSyntax level level Undo level Related command display local-user,service-type Local-userExample # Set the level of user user1 to Example # Add a local user named user1 Local-user password-display-mode PasswordRelated command display local-user , password Self-service-url Service-type Service-type ftp Service-type pppRelated command service-type ppp and service-type ftp Syntax service-type ftp Undo service-type ftp State State active block Related command domain Work-directory# Place the current user user1 to the state of blocked Syntax work-directory directory-name Undo work-directory 1947 AAA Configuration Commands Radius Configuration Commands Accounting-on enable128 Radius scheme Accounting-on enable interval Accounting-on enable sendRelated command radius scheme, accounting-on enable Data-flow-format Radius scheme view GigabyteMega-packet, or giga-packet Packets to be sent to a Radius server Related command display radius scheme Related command radius schemeExample # Display the configurations of all Radius schemes Display radius scheme Display radius statistics Display radius statisticsExample # Display statistics about Radius packets 1953 State statistictotal=1024 State statistics 1955 Dead Display stop-accounting-buffer Which is a string of 1 to 32 charactersTime range, or user name On August 31 Key Radius scheme view Nas-ip Radius scheme viewDisplay radius scheme Related command radius nas-ip Primary accounting Radius scheme viewUndo primary accounting Primary authentication Radius scheme view 1959 Syntax radius client enable Undo radius client Example # Enable the listening port of the Radius clientRadius client Radius nas-ip Related command nas-ip Radius scheme view Radius schemeUndo radius nas-ip Undo radius scheme radius-scheme-name Radius trap Reset radius statistics Reset stop-accounting-bufferSyntax reset radius statistics Example # Clear Radius statistics Retry Undo retry Retry realtime-accounting 1965 Retry stop-accounting Radius scheme view Secondary accounting Radius scheme viewUndo secondary accounting Secondary authentication Radius scheme view 1967 Security-policy-server Server-typeSyntax server-type extended standard Undo server-type View Radius scheme view Use the state command to set the status of a Radius server Primary Sets the status of the primary Radius serverSecondary Sets the status of the secondary Radius server Accounting Sets the status of the Radius accounting server Stop-accounting-buffer enable Radius scheme view Timer quiet Radius scheme view Timer realtime-accounting Radius scheme viewSyntax timer quiet minutes Undo timer quiet 1971 Timer response-timeout Radius scheme view Related command retry realtime-accounting,radius schemeNumber of users Real-time accounting interval minute Related command radius scheme, retry User-name-format Radius scheme viewUser-name-format with-domain without-domain Radius Configuration Commands Hwtacacs Configuration Commands Related command display hwtacacs129 Data-flow-format Hwtacacs scheme view Related command hwtacacs scheme Description on the fields of the display hwtacacs command Hwtacacs nas-ip Scheme view , retry stop-accounting Hwtacacs scheme viewAddress or a loopback address Related command nas-ip Hwtacacs scheme view Hwtacacs schemeUndo hwtacacs scheme hwtacacs-scheme-name Key accounting authentication authorization string Undo key accounting authentication authorization stringKey Hwtacacs scheme view Nas-ip Hwtacacs scheme view Related command hwtacacs nas-ip Primary accounting Hwtacacs scheme view Primary authentication Hwtacacs scheme view Example # Set the primary authentication server1981 Primary authorization Reset hwtacacs statisticsUndo primary authorization Accounting Clears Hwtacacs accounting statistics Retry stop-accounting Hwtacacs scheme view Secondary authentication Hwtacacs scheme view Syntax secondary authentication ip-address port-numberSecondary accounting Hwtacacs scheme view Secondary authorization Example # Configure the secondary authentication server1985 Stop-accounting-buffer enable Hwtacacs scheme view Example # Configure the secondary authorization serverView Hwtacacs scheme view Timer quiet Hwtacacs scheme view Timer realtime-accounting Hwtacacs scheme view1987 Timer response-timeout Hwtacacs scheme view User-name-format Hwtacacs scheme view Hwtacacs scheme Hwtacacs Configuration Commands Packet Filter Firewall Configuration Commands Switch running a routing protocolDisplay firewall ethernet-frame-filter All Displays all the firewall statistics information Firewall default Syntax firewall default permit denyDisplay firewall-statistics Fragments-inspect Firewall enable Firewall enableUndo firewall enable Firewall ethernet-frame-filter Example # Enable fragments inspection Firewall fragments-inspect Firewall fragments-inspect high low number default Firewall fragments-inspect high lowFirewall ipv6 fragments-inspect Undo firewall fragments-inspect high low Related command firewall fragments-inspect Firewall packet-filter Reset firewall ethernet-frame-filter Firewall packet-filter ipv6Outbound Undo firewall packet-filter ipv6 inbound outbound Reset firewall-statistics Example # Clear all the firewall statistic information# Clear the firewall statistic information of Ethernet 1/0 Aspf Configuration Commands 131Aging-time Aging-time syn fin tcp udp seconds # Set the TCP idle timeout period to 3000 seconds # Set the UDP idle timeout period to 110 secondsAspf-policy Display aspf all Syntax display aspf all2001 Display aspf interface Syntax display aspf interface Display aspf policy Display aspf sessionSyntax display aspf policy aspf-policy-number Display aspf session verbose Display port-mapping Related command port-mapping Firewall aspfExample # Display all the information about port mapping 2005 Log enable Syntax log enable Undo log enableExample # Enable the session logging function of the Aspf Port-mapping Reset aspf session Related command display port-mappingSyntax reset aspf session Example # Map port 3456 to the FTP protocol Aspf Configuration Commands MAC Authentication Configuration Commands Display mac-authenticationSyntax display mac-authentication interface interface-list DFIC-9FSW and MSR 20 Series Products Mac-authentication MAC Addr Mac-authentication domain 2011 Mac-authentication timer Related command display mac-authentication Mac-authentication user-name-format Reset mac-authentication statistics NAT Configuration Commands Connection-limit default actionConnection-limit default amount 133 Connection-limit enable Connection-limit enableUndo connection-limit enable Connection-limit policy Display connection-limit policy Example # Create a connection-limit policy numberedSyntax display connection-limit policy policy-numberall 2017 Display connection-limit statistics Display nat address-group Display nat address-groupView Any view Parameter None Information Display nat aging-time Display nat allDisplay nat aging-time Different NAT sessions Description on some fields of the display nat all command 2021 Display nat connection-limit Destination address Display nat log Mask-length The length of net mask, in the range 1 toSyntax display nat log 2023 # View the NAT log configuration Description on the fields of the display nat log commandDisplay nat outbound Display nat outbound Display nat server Display nat sessionSyntax display nat server Display nat statistics Example # Display the active NAT sessionsSyntax display nat statistics Display userlog export Limit acl Limit mode Syntax limit mode amount Undo limit modeView Connection-limit policy view Nat address-group Nat aging-timeUndo nat address-group group-number Tcp-syn udp seconds Nat alg Nat connection-limit-policy 2031 Nat log enable Nat log flow-active Nat log flow-begin Nat outboundNat log flow-begin Undo nat log flow-begin NAT Configuration Commands # Configure the address pool Nat outbound staticNat server Syntax nat outbound static Undo nat outbound static NAT Configuration Commands 2037 # Remove the WWW server using the following commands Nat static Reset nat session Syntax reset nat session2039 Reset userlog export Reset userlog nat logbufferRelated command display userlog export Userlog nat export host Related command userlog nat export source-ip Related command userlog nat export hostUserlog nat export source-ip 2041 Userlog nat export version Userlog nat syslogSyntax userlog nat syslog Undo userlog nat syslog PKI Configuration Commands 134 Ca identifier Syntax ca identifier name Undo ca identifier Certificate request entity Certificate request fromPki entity Certificate request mode Simple password * manualUndo certificate request mode Certificate request polling Related command display pki certificate Certificate request urlUndo certificate request polling count interval 2047 Common-name CountrySyntax common-name name Undo common-name Undo country Crl update-period Crl check disable enableCrl update-period hours Undo crl update-period Crl url Display pki certificateUndo crl url Example # Display the local certificate 2051 Display pki certificate access-control-policy Display pki certificate attribute-group Related command pki retrieval-crl domain and pki domain Display pki crl domainSyntax display pki crl domain domain-name Example # Display the locally saved CRLs Fqdn Ip PKI entity viewUndo fqdn Undo ip Ldap-server LocalityUndo ldap-server Undo locality Organization Organizational-unitSyntax organization org-name Undo organization Pki certificate access-control-policy Pki certificate attribute-group2057 Pki delete-certificate Pki domainSyntax pki domain domain-nameundo pki domain domain-name Pki entity Pki import-certificatePki entity entity-name Undo pki entity entity-name Related command pki domain Pki request-certificate domain Related command Pki domain Example Pki retrieval-certificatePki retrieval-crl domain Pki retrieval-certificate ca local domain domain-name Pki validate-certificate Root-certificate fingerprintPki validate-certificate ca local domain domain-name Root-certificate fingerprint md5 sha1 string Rule access control policy view Syntax rule id deny permit group-name Undo rule id all2063 Undo state Portal Configuration Commands Portal authentication135 Display portal acl Description on the fields of the display portal acl command Display portal connection statisticsAll Displays portal connection statistics on all interfaces Statistics on the specified interface 2067 Msgauthenack Msgauthorack Msgloginack Msglogoutack Display portal free-ruleSyntax display portal free-rule rule-number Related command portal free-rule Display portal interface2069 Related command portal server Display portal serverSyntax display portal server server-name URL Display portal server statistics All Displays portal server statistics on all interfaces2071 Reqchallenge Display portal tcp-cheat statistics Syntax display portal tcp-cheat statistics Display portal user Specified interface enabling portalSpecified interface or all interfaces enabling portal 2073 Portal auth-network Undo portal auth-network network-addressall Related command display portal user Portal delete-userPortal free-rule Undo portal free-rule rule-numberall Related command display portal free-rule Portal resource-name Related command display portal server Portal serverUndo portal server server-name key port url 2077 Reset portal connection statistics Portal server method Reset portal server statistics Reset portal tcp-cheat statisticsReset portal tcp-cheat statistics Portal Configuration Commands RSH Configuration Commands 136Rsh INSTALL.LOG Common Configuration Commands Description on the fields of the display time-range commandDisplay time-range Time-range Common Configuration Commands 2085 Common Configuration Commands IPV4 ACL Configuration Commands 138Acl 2087 Acl copy # Create IPv4 ACL 2002, giving the ACL a name of flow# Delete the IPv4 ACL with the number # Delete the IPv4 ACL named flow Acl name Syntax acl name acl-name2089 Description for IPv4 # Define the description of IPv4 ACL# Define the description of ACL Description on the fields of the display acl command Display aclSyntax display acl acl-numberall name acl-name 2091 Reset acl counter Syntax reset acl counter acl-number all name acl-nameRule in basic IPv4 ACL view # Clear statistics about IPv4 ACL flow 2093 Rule in advanced IPv4 ACL view TCP/UDP-specific parameters for advanced IPv4 ACL rules Parameter Function Description Icmp-type Icmp message Type Code Rule in Ethernet frame header ACL view Undo rule rule-id2097 Rule in user-defined ACL view View User-defined ACL view Support to this command varies by device Rule comment for IPv4# Create a user-defined ACL rule Syntax rule rule-idcomment text Undo rule rule-idcomment Step for IPv4 # Create a rule in ACL 3000 and define the rule description# Create a rule in ACL 4000 and define the rule description # Create a rule in ACL 5000 and define the rule description Example # Set the rule numbering step to 2 for ACL 2101 IPV4 ACL Configuration Commands IPV6 ACL Configuration Commands 139Acl ipv6 2103 Acl ipv6 copy # Create IPv6 ACL 2002, giving the ACL a name of flow# Delete the IPv6 ACL with the number # Delete the IPv6 ACL named flow Acl ipv6 name Syntax acl ipv6 name acl6-name2105 Description for IPv6 Display acl ipv6# Create a description for IPv6 ACL Syntax display acl ipv6 acl6-numberall name acl6-name Reset acl ipv6 counter All All basic and advanced IPv6 ACLs2000 to 2999 for basic IPv6 ACLs 3000 to 3999 for advanced IPv6 ACLs Rule in basic IPv6 ACL view # Clear the statistics about the IPv6 ACL named flowUndo rule rule-id fragment logging source time-range Rule in advanced IPv6 ACL view 2109 Parameter Function Description Source source Destination destTime-range time-name TCP/UDP-specific match criteria for advanced IPv6 ACL rules ICMPv6-specific match criteria for advanced IPv6 ACL rulesAvailable ICMPv6 messages Rule in simple IPv6 ACL view View Simple IPv6 ACL view Parameters for simple IPv6 ACL rules TCP/UDP-specific parameters for simple IPv6 ACL rules ICMPv6-specific parameters for simple IPv6 ACL rulesICMPv6 messages definable in simple IPv4 ACL rules Support for this command varies by device Rule comment for IPv62115 Step for IPv6 Example # Set the rule numbering step to 2 for IPv6 ACL # Set the rule numbering step to 2 for IPv6 ACL 2117 IPV6 ACL Configuration Commands Ipsec Configuration Commands Ah authentication-algorithmCryptoswitch fabric enable 140 Display encrypt-card fast-switch Syntax display encrypt-card fast-switch Display ipsec policy Display ipsec policy brief name policy-name seq-numberIpsec policy system view # Display detailed information about all IPSec policies Display ipsec policy-template IPSec policy template group10000 Template group Related command ipsec proposal Display ipsec proposalDisplay ipsec sa Syntax display ipsec proposal proposal-name Reset ipsec sa, ipsec sa global-duration Description on the fields of the display ipsec sa command Related command reset ipsec session Display ipsec sessionSyntax display ipsec session tunnel-id integer Example # Display information about all IPSec sessions Related command reset ipsec statistics Display ipsec statisticsSyntax display ipsec statistics Example # Display IPSec packet statistics Display ipsec tunnel Syntax display ipsec tunnel2129 Encrypt-card fast-switch Encapsulation-mode Esp authentication-algorithm Related command display encrypt-cardfast-switchEsp encryption-algorithm Syntax esp encryption-algorithm 3des aes key-length des Ike-peer IPSec policy view/IPSec policy template view Undo esp encryption-algorithmSyntax ike-peer peer-name Undo ike-peer peer-name Related command ipsec policy-template Ipsec binding policy2133 Ipsec cpu-backup Syntax ipsec cpu-backup enable Undo ipsec cpu-backup enable Ipsec policy interface view 2135 Ipsec policy system view Syntax ipsec policy policy-nameseq-number isakmp manual Ipsec policy isakmp template Ipsec policy-templateUndo ipsec policy-template template-name seq-number 2137 Related command display ipsec policy-template Related command display ipsec proposalIpsec proposal Related command sa duration, display ipsec sa duration Ipsec sa global-durationIpsec session idle-time Example # Create an IPSec proposal named newprop1 Pfs Undo ipsec session idle-timePfs dh-group1 dh-group2 dh-group5 dh-group14 Undo pfs Example # Enable and configure PFS for IPSec policy policy1 Related command ipsec proposal, ipsec policy system viewProposal Undo proposal proposal-name Reset encrypt-card fast-switch Reset ipsec saSyntax reset encrypt-card fast-switch Reset ipsec session Related command display ipsec saSyntax reset ipsec session tunnel-id integer Reset ipsec statistics Sa authentication-hexRelated command display ipsec session Syntax reset ipsec statistics Sa duration View IPSec policy view/IPSec policy template view2145 Sa encryption-hex Sa spi 2147 Sa string-key Example # Configure IPSec policy policy1 to reference ACL Security aclSyntax security acl acl-number Undo security acl 2149 Example # Configure IPSec proposal prop1 to use AH TransformTunnel local Syntax transform ah ah-esp esp Undo transform Tunnel remote 2151 Example # Set the remote address of the IPSec tunnel to IKE Configuration Commands 141Ike proposal, display ike proposal Related command ike proposal, display ike proposal Certificate domainDh group1 group2 group5 group14 Undo dh Related command ike dpd Display ike dpdExample # Specify 768-bit Diffie-Hellman for IKE proposal Syntax display ike dpd dpd-name Related command ike peer system view Display ike peerDisplay ike proposal Syntax display ike peer peer-name Example # Display the settings of IKE proposals Related command ike proposal, ike peer system viewDisplay ike sa 2157 # Display detailed information about the current IKE SAs 2159 Dpd Undo dpdEncryption-algorithm 3des-cbc aes-cbc key-length des-cbc Related command Id-type Example Exchange-modeId-type Ike dpd Ike local-nameExample # Use the ID type of name in IKE negotiation Syntax ike dpd dpd-name Undo ike dpd dpd-name Ike next-payload check disabled Related command remote-name,id-typenameExample # Configure the local gateway name as app 2163 Related command display ike proposal Ike peer system viewIke proposal Syntax ike peer peer-name Undo ike peer peer-name Ike sa keepalive-timer interval Ike sa keepalive-timer timeoutRelated command ike sa keepalive-timer timeout Example # Set the keepalive interval to 200 seconds Ike sa nat-keepalive-timer interval Related command ike sa keepalive-timer intervalExample # Set the keepalive timeout to 20 seconds Interval-time Local Local-address Nat traversal Syntax nat traversal Undo nat traversalPeer multi-subnet single-subnet Undo peer Related command authentication-algorithmon Pre-shared-keyRemote-address Syntax pre-shared-key key Undo pre-shared-key Reset ike sa Related command id-typeip, local-addressRelated command id-type,ike local-name Remote-name Related command display ike sa Example # Clear the IPSec tunnel toSyntax sa duration seconds Undo sa duration 2171 Related command ike proposal and display ike proposal Time-outSyntax time-out time-out Undo time-out SSH2.0 Configuration Commands 142Display public-key local Public-key local create Example Display public-key peer Display public-key peer brief name publickey-nameBrief Displays brief information about all public keys Specified or all public keys Related command sftp client source Display sftp client source# Display brief information about all public keys Syntax display sftp client source Related command ssh client source Display ssh client sourceDisplay ssh server Syntax display ssh client source Display ssh server-info # Display the session information of the SSH serverSyntax display ssh server-info 2177 Related command ssh user Display ssh user-informationSyntax display ssh user-information username Example # Display information about all SSH users Related command Public-key peer Example Peer-public-key endPublic-key-code begin Peer-public-key end Public-key-code end Public-key local createPublic-key-code end Public-key peer, public-key-code begin Public-key local destroy Public-key local destroy, display public-key local Example# Create local RSA key pair # Create local DSA key pair Related command public-key local create Public-key local export rsaPublic-key local export rsa openssh ssh1 ssh2 filename Public-key local create , public-key local destroy Public-key local export dsa # Display the RSA local public key in OpenSSH formatPublic-key local export dsa openssh ssh2 filename # Export the DSA local public key in OpenSSH format Related command public-key-code begin, public-key-code end Public-key peer# Display the DSA local public key in OpenSSH format Syntax public-key peer keyname Undo public-key peer keyname Public-key peer import sshkey Sftp2185 Sftp client ipv6 source Undo sftp client ipv6 sourceIpv6 ipv6-address Specifies a source IPv6 address Related command Display sftp client source Example Sftp client sourceSftp ipv6 Sysname sftp ipv6 Input Username Sftp server enable Sftp server idle-timeoutSyntax sftp server enable Undo sftp server enable Related command display ssh server Ssh client authentication server Ssh client first-time enable To access the SSH server Ssh client ipv6 sourceSsh client source Undo ssh client ipv6 source Ssh server authentication-retries Related command display ssh client source Ssh server authentication-timeout Ssh server compatible-ssh1x enableBy default, the authentication timeout period is 60 seconds Example # Enable the SSH server to work with SSH1.x clients Ssh server enable Syntax ssh server enable Undo ssh server enableSsh server rekey-interval Ssh user Undo ssh user username2195 Related command display ssh user-information Ssh2 Ssh2 ipv6 2197 SSH2.0 Configuration Commands 2199 SSH2.0 Configuration Commands Sftp Configuration Commands 143Bye Syntax bye Cdup DeleteDir Syntax cdup Exit GetSyntax exit 2203 Help Mkdir Put2205 Pwd QuitSyntax pwd Syntax quit Remove RenameRmdir 2207 Sftp-client rmdir temp1 Directory successfully removed SSL Configuration Commands 144Ciphersuite View SSL server policy view Client-verify enable Syntax client-verify enable Undo client-verify enableExample # Set the SSL connection close mode to wait Close-mode wait Display ssl client-policy Display ssl server-policySyntax display ssl client-policy policy-nameall Syntax display ssl server-policy policy-nameall Handshake timeout Syntax handshake timeout time Undo handshake timeoutPki-domain Syntax pki-domain domain-name Prefer-cipher Undo pki-domainUndo prefer-cipher 2213 Session cachesize size timeout time Undo session cachesize timeoutSession Rsaaes128cbcsha Ssl client-policy Ssl server-policy2215 Use the undo version command to restore the default Version ssl3.0 tls1.0SSL client policy view Ssl3.0 Specifies SSL Backup Center Configuration Commands Display standby flowSyntax display standby flow Main and backup interfaces Display standby stateDisplay standby state Following tables describe the meanings of each state Backup states of the backup interface Backup flagsStandby bandwidth Syntax standby bandwidth size Undo standby bandwidth Related command standby interface Standby interface Related commands standby track Standby thresholdUndo standby threshold 2221 Standby timer delay Related command standby interface and standby bandwidthUndo standby timer delay Standby timer flow-check Standby trackUndo standby track 2223 Standby interface, track on IPV4-BASED Vrrp Configuration Commands Display vrrp Description on the fields of the display vrrp command Vrrp vrid track interface commandVrrp vrid track command Display vrrp statistics Example # Display the statistics about all standby groups 2227 Reset vrrp statistics Vrrp vrid authentication-mode255 Device are cleared Vrrp method Syntax vrrp method real-mac virtual-mac Undo vrrp method2229 Vrrp ping-enable Vrrp ping-enableUndo vrrp ping-enable Addresses of standby groups Default mode is immediate preemption without delay Vrrp un-check ttlVrrp vrid preempt-mode Syntax vrrp un-check ttl Undo vrrp un-check ttl Vrrp vrid priority Vrrp vrid timer advertise Vrrp vrid track2233 Vrrp vrid track interface Vrrp vrid virtual-ip 2235 # Add virtual IP address 10.10.10.11 to standby group Vrrp Configuration Commands For IPV6 147Display vrrp ipv6 IPv6 Vrrp ipv6 vrid track command Display vrrp ipv6 statistics 2239 Reset vrrp ipv6 statistics Vrrp ipv6 methodSyntax vrrp ipv6 method real-mac virtual-mac Vrrp ipv6 ping-enable Vrrp ipv6 ping-enableUndo vrrp ipv6 ping-enable Undo vrrp ipv6 method Vrrp ipv6 vrid authentication-mode Vrrp ipv6 vrid preempt-mode Vrrp ipv6 vrid priority Undo vrrp ipv6 vrid virtual-router-idpriority2243 Vrrp ipv6 vrid timer advertise Undo vrrp ipv6 vrid virtual-router-idtimer advertise Vrrp ipv6 vrid track 2245 # Configure the virtual IPv6 address of standby group 1 as Vrrp ipv6 vrid virtual-ip Device Management Commands 148 Bootrom Buzzer enableSyntax buzzer enable Undo buzzer enable Part Display boot-loader This command is applicable on MSR 50 series routers onlyDisplay boot-loader slot slot-number Related command Boot-loader Display cpu-usage Display cpu-usage task number offset verbose from-device Description on fields of the display boot-loader command Display deviceSyntax display device cf-card usb slot slot-numberverbose 2251 Cf-card Displays information of a compact Flash CF Usb Displays information of a universal serial bus USBVaries with devices Such as card, CF, USB, VCPM, VPM and DSP Description on fields on the display device command 2253Cpld Display device manuinfo Display device manuinfo slot slot-numberInformation about the device Display # Display the temperature information of cards Display environmentExample # Display manufacturing information of a device Display environment Display fan Display licenseDisplay fan fan-id Display license Display power Syntax display power power-idDisplay memory Syntax display memory Display reboot-type Display schedule rebootDisplay reboot-type slot slot-number Display schedule reboot Reboot Only users at management level can execute this commandReboot slot slot-number License register Reset unused porttag Use the remove command to remove a cardSyntax reset unused porttag Remove slot slot-number Schedule reboot at Syntax schedule reboot at hhmm date Undo schedule reboot2261 Schedule reboot delay Syntax schedule reboot delay hhmm mm Undo schedule reboot Temperature-alarm enable 2263 Temperature-limit Undo temperature-limit slot-number NQA Client Configuration Commands Data-fillSyntax data-fill string Undo data-fill Data-size Description any NQA test type viewSyntax data-size size Undo data-size Destination ip Destination portSyntax destination ip ip-address Undo destination ip Syntax destination port port-number Undo destination port Syntax display nqa result history admin-nameoperation-tag Display nqaResult Displays the results of the last test History Displays the history records of a test Description on the fields of the display nqa result command 2269 # Display the history records of tests Field Description Index History record number Filename FrequencySyntax filename filename Undo filename Syntax frequency interval Undo frequency History-records Syntax history-records number Undo history-records Http-version Next-hopHttp-version Undo http-version Nqa agent enable Syntax nqa agent enable Undo nqa agent enableRelated command nqa server enable Nqa Example # Enable the NQA client Nqa agent max-concurrentNqa schedule 2275 Operation FTP test type view Operation Http test type viewOperation get put Undo operation Password FTP test type view Syntax password password Undo passwordOperation interface Undo operation interface Probe count Syntax probe count times Undo probe count Probe packet-interval Probe packet-number2279 Probe packet-timeout Probe timeoutSyntax probe timeout timeout Undo probe timeout Reaction 2281 Reaction trap Route-option bypass-routeUndo reaction trap probe-failure test-complete test-failure Related command source ip Source interfaceUndo source interface 2283 Related command source interface Source ipSource port Syntax source ip ip-address Undo source ip Tos TtlSyntax tos value Syntax ttl value Type Url Username FTP test type viewSyntax url url Undo url Vpn-instance ICMP-echo test type view Syntax vpn-instance instance Undo vpn-instance NQA Server Configuration Commands 150Display nqa server status Syntax display nqa server status Nqa server enable Syntax nqa server enable Undo nqa server enableRelated command nqa server tcp-connect,nqa server udp-echo Example # Enable the NQA server Nqa server udp-echo Undo nqa server udp-echo ip-addressport-number2291 Sysname nqa server udp-echo 169.254.10.2 Netstream Configuration Commands Display ip netstream cacheSyntax display ip netstream cache Ip netstream statistics command Display ip netstream exportDisplay ip netstream export Exported NetStream UDP packets Enable Syntax enableUndo enable Related command ip netstream aggregation Ip netstream aggregation Source-prefix Ip netstream export host Ip netstream export sourceExample # Enter NetStream AS aggregation view 2297 Ip netstream export version Ip netstream timeout active Related command ip netstream timeout inactiveIp netstream max-entry 2299 Ip netstream timeout inactive Reset ip netstream statisticsRelated command ip netstream timeout active Reset ip netstream statistics NTP Configuration Commands Display ntp-service sessionsSyntax display ntp-service sessions verbose 152 Display ntp-service status Display ntp-service statusExample # View the NTP service status information Display ntp-service trace Syntax display ntp-service trace2303 Ntp-service access Undo ntp-service access peer query server synchronizationProtection. a more secure method is identity authentication Sure you have already created and configured this ACL Ntp-service authentication enable Ntp-service authentication-keyidBy default, NTP authentication is disabled # Enable NTP authentication Ntp-service broadcast-client Ntp-service broadcast-server Ntp-service in-interface disable 2307 Ntp-service max-dynamic-sessions Ntp-service multicast-client Ntp-service multicast-server Ntp-service refclock-masterUndo ntp-service multicast-server ip-address 2309 Ntp-service reliable authentication-keyid Ntp-service source-interfaceUndo ntp-service source-interface Used as a reference clock Ntp-service unicast-peer Ntp-service unicast-server Vpn-instance-name in your commandPublic network No NTP server is designated for the device by default Designated for the deviceInterface and the NTP server coexist in this VPN 2313 NTP Configuration Commands Rmon Configuration Commands Display rmon alarmSyntax display rmon alarm entry-number Related command rmon alarm Related command rmon event Example # Display the configuration of Rmon event tableDescription on the fields of the display rmon event command Display rmon event Display rmon eventlog Display rmon historySyntax display rmon eventlog entry-number 2317 Related command rmon history Display rmon prialarm Syntax display rmon prialarm entry-numberRelated command rmon prialarm Current-configuration and display this commands you cannot Related command rmon statistics With the display current-configuration and displayDisplay rmon statistics Rmon alarm Undo rmon alarm entry-number2321 Table with the rmon event command You can create up to 60 alarm entriesRising alarm and falling alarm are alternate Rmon event You can create up to 100 alarm entries Rmon historyUndo rmon history entry number Display rmon history Rmon prialarm Undo rmon prialarm entry-number2325 Configurations the same and the creation fails You can create up to 50 pri-alarm entries# Remove private alarm entry Rmon statistics 2327 Rmon Configuration Commands Snmp Configuration Commands Display snmp-agent local-switch fabricid154 Display snmp-agent community Display snmp-agent group Syntax display snmp-agent group group-nameDescriptions on the fields of display snmp-agent community Display snmp-agent mib-view Name of the specified MIB view2331 Display snmp-agent statistics Syntax display snmp-agent statistics Display snmp-agent sys-info Display snmp-agent sys-info contact location versionVersion Displays the version of the current Snmp agent 2333 Related command snmp-agent trap enable Display snmp-agent trap-listSyntax display snmp-agent trap-list Enable snmp trap updown Syntax enable snmp trap updown Undo enable snmp trap updownDisplay snmp-agent usm-user # Display SNMPv3 information for the user aa Snmp-agent Snmp-agentUndo snmp-agent Snmp-agent community Undo snmp-agent community community name Undo snmp-agent group v3 group-name authentication privacy Related command snmp-agentmib-view,snmp-agentusm-userSnmp-agent group Undo snmp-agent group v1 v2c group-name Snmp-agent local-switch fabricid Snmp-agent logSnmp-agent usm-user Snmp-agent mib-view Undo snmp-agent mib-view view-name Related command snmp-agent group Snmp-agent packet max-sizeSnmp-agent sys-info 2341 Related command Display snmp-agentsys-info Snmp-agent target-host 2343 Snmp-agent trap enable Linkup warmstart * system voice vrrp authfailure newmaster Snmp-agent trap if-mib link extended Snmp-agent trap if-mib link extendedUndo snmp-agent trap if-mib link extended NMS, the device may not be able to resolute the messages Snmp-agent trap life Snmp-agent trap queue-size Example # Configure the size of the Trap queue to Snmp-agent trap sourceSnmp-agent usm-user Undo snmp-agent trap source Parameter v1 SNMPv1 2349 Snmp Configuration Commands File System Configuration Commands Copy Syntax delete /unreserved file-url Syntax dir /all file-url Execute Syntax execute filename2353 File prompt FixdiskFile prompt alert quiet Syntax fixdisk device Format Syntax format device# create a subdirectory named mytest under test 2355 More MountSyntax more file-url Syntax mount device Related command Example Umount Move# Mount a CF card on a centralized device 2357 Reset recycle-bin Syntax reset recycle-bin /forceExample # Move the file cf/test/sample.txt to cf/sample.txt Example # Rename the file sample.txt as sample.bak Umount Syntax umount device2359 Related command mount UndeleteExample # Unmount a CF card on a device Syntax undelete file-url Configuration File Management Commands Backup startup-configurationDisplay saved-configuration Syntax display saved-configuration by-linenum Configuration File Management Commands Reset saved-configuration Related command startup saved-configurationReset saved-configuration backup main Display startup Restore startup-configuration Related command save, display saved-configuration Syntax save file-name safely backup main Save2365 Startup saved-configuration Related command display startup 2367 Configuration File Management Commands FTP Server Configuration Commands Related command ftp timeout and ftp update157 Display ftp-server Ftp server enable Syntax ftp server enable Undo ftp serverDescription on the fields of the display ftp-user command Free ftp user Ftp timeout Ftp updateSyntax ftp timeout minute Undo ftp timeout Syntax ftp update fast normal Undo ftp update Sysname system-view Sysname ftp update normal FTP Client Configuration Commands 158Ascii Binary Syntax cd pathname Close DebuggingSyntax close Syntax debugging Undo debugging Description on the fields of the debugging command View FTP client view Parameter remotefile File name # View the content of aa.txt DisconnectSyntax disconnect 2377 Display ftp client configuration Syntax display ftp client configurationRelated command ftp client source Ftp Ftp client source Ftp client sourceUndo ftp client source Related command display ftp client configuration Ftp ipv6 2381 Lcd Syntax lcd # View the content of file aa.txt Open2383 Related command close Open ipv6 Passive Syntax passiveUndo passive 2385 Parameter protocol-command FTP command Remotehelp # Display the help information for the user command Description on the fields of the remotehelp command2387 Nlst SiteSyst Stat Verbose Syntax verboseUndo verbose 2389 FTP Client Configuration Commands Tftp Client Configuration Commands Display tftp client configuration159 Tftp-server acl Tftp # Associate IPv6 ACL 2001 with Tftp application in Ipv6 Related command tftp client source IP address configured on the deviceTftp client source On the source interface, the transmission fails Related command display tftp client configuration Tftp ipv6 2395 Tftp Client Configuration Commands System Maintaining Commands 160Ping Ping ipv6 2399 Tracert Range 1 to 65535, defaulting to 65535, in milliseconds. The default value is 5000 msTracert ipv6 With IPv6 address System Maintaining Commands System Debugging Commands 161Undo debugging all module-name option View User view Parameter all All debugging functions Related command display debugging Display debuggingDebugging Basic Configuration Commands 162Clock datetime Clock summer-time one-off Basic Configuration Commands Clock summer-time repeating 2407 Clock timezone Command-privilege Command-privilege level level view view commandUndo command-privilege view view command Display clock Configure-user count Description Related commandDisplay configure-user Display clipboard Display configure-user Syntax display configure-userDisplay clock Syntax display clock Display current-configuration Related command configure-user countExclude text Special characters in regular expression 2413 Display diagnostic-information # Display the configuration beginning with userDisplay diagnostic-information Version, display device, display current-configuration Display history-command Syntax display history-commandDisplay hotkey Display hotkey Display this Syntax display this by-linenum Display version Syntax display version2417 Header incoming legal login motd shell text Undo header incoming legal login motd shellHeader Hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu command Ctrl+G corresponds to display current-configurationHotkey Undo hotkey Ctrlg Ctrll Ctrlo Ctrlt Ctrlu # Display the configuration of hotkeys Related command quit ReturnSuper Syntax return Super password Related command super passwordSuper password level user-level simple cipher password Undo super password level user-level # Display the password for switching user-level SysnameSyntax sysname sysname Undo sysname 2423 Related command quit, return System-viewSyntax system-view Example # Enter system view from the current user view Information Center Configuration Commands Description on the fields of the display channel commandDisplay channel Example # Display information for channel Display info-center Syntax display info-center Description on the fields of the display info-center command 2427 Display logbuffer Represents information level, in the range 0 toSeverity description Meanings of characters in text Descriptions on the fields of the display logbuffer command Rest is omitted here2429 Display logbuffer summary Display logfile bufferDisplay logbuffer summary level severity Syntax display logfile buffer Support for the command varies with devices Example # Display the contents of the log file bufferDisplay logfile summary Syntax display logfile summary Display trapbuffer Info-center channel nameDisplay trapbuffer size buffersize Trap buffer, in the range 1 to 1,024 Info-center console channel 2433 Info-center enable Syntax info-center enable Undo info-center enableInfo-center logbuffer Undo info-center logbuffer channel size Info-center logfile enable Example # Enable the log file featureInfo-center logfile frequency 2435 Info-center logfile switch-directory Syntax info-center logfile switch-directory dir-nameInfo-center logfile size-quota Info-center loghost # Set the directory to save the log file to cf/testUndo info-center loghost host-ip 2437 Info-center loghost source Undo info-center loghost source Info-center monitor channel Info-center snmp channelUndo info-center snmp channel 2439 Info-center source Default output rules for different output directions Output Modules Enabled Direction Allowed Disabled Severity2441 NMS Info-center synchronous Info-center timestamp Info-center timestamp loghost Info-center timestamp loghost date no-year-date noneUndo info-center timestamp loghost Info-center trapbuffer Logfile saveUndo info-center trapbuffer channel size Syntax logfile save Reset logbuffer Reset trapbufferTerminal debugging Terminal logging Undo terminal debuggingSyntax terminal logging Undo terminal logging Terminal monitor Terminal trapping Sysname terminal trapping Current terminal trapping is on User Interface Configuration Commands Acl ipv6 acl-number inbound outboundUndo acl ipv6 acl-number inbound outbound Acl acl-number inbound Activation-key Syntax activation-key character Undo activation-key Auto-execute command 2451 None Performs no authentication Password Performs local password authenticationAAA, refer to AAA Configuration Commands on Users log onto the device using the current user interface Databits Databits 5 6 7Undo databits Display history-command History-commandmax-sizeDisplay user-interface # Display summary about all user interfaces 2455 Description on the fields of the display users command Display usersDisplay users all All Displays information about users on all user interfaces Syntax escape-key default character Undo escape-key Escape-keyExample # Define a as the escape key 2457 None Free user-interface Syntax free user-interface num1 aux console tty vty num22459 History-command max-size # Terminate the connection with user interface VTYView User interface view Password next time you enter the system LockLock Operating under the active user interface Only, and cannot be applied to the Console port Example # Set the answering mode to auto-answer Example # Set the timeout interval to 50 secondsParity Syntax parity even mark none odd space Undo parity Example # Enable the VTYs 0 through 4 to support SSH only Protocol inboundExample # Perform odd parity check on the AUX interface Syntax protocol inbound all pad ssh telnet Redirect enable Redirect enableUndo redirect enable Redirect disconnect Related command telnet, display tcp statistics on Redirect listen-portRedirect refuse-negotiation Redirect listen-port port-number Redirect return-deal from-telnet Redirect return-deal from-telnetUndo redirect return-deal from-telnet Redirect timeout Redirect return-deal from-terminal Screen-length SendSyntax screen-length screen-length Undo screen-length Syntax send all num1 aux console tty vty num2 Set authentication password Set authentication password cipher simple passwordUndo set authentication password Related command authentication-mode ShellSyntax shell Undo shell Speed in user interface view Stopbits Terminal type User privilege level Syntax user privilege level level Undo user privilege level # Enable user 1 to access level 3 commands User-interface# Enter the user interface view of VTY 0 to User Interface Configuration Commands MAC Address Table Management Configuration Commands Display mac-addressEthernet interfaces Display mac-address blackhole vlan vlan-id count Display mac-address aging-time Display mac-address mac-learningSyntax display mac-address aging-time Port Index Mac-address Ethernet interface view 2479 Related command display mac-address Mac-address system viewBlackhole MAC address entries are dropped Specified Vlan ID, in the range 1 to Mac-address mac-learning disable 2481 Related command display mac-addressmac-learning Example # Disable global MAC address learningMac-address max-mac-count Ethernet interface view Mac-address timer Mac-address timer aging seconds no-agingUndo mac-address timer aging MAC Address Table Management Configuration Commands POE Configuration Commands 166Apply poe-profile Module, and slot of the power sourcing equipment PSE Description on fields of the display poe device commandDisplay poe device Display poe interface 2487 Description on fields of the display poe interface command # Display the state of all PoE interfaces Display poe interface power 2489 Display poe power-usage # Display the power information of all PoE interfacesSyntax display poe power-usage Display poe pse Syntax display poe pse pse-id2491 Display poe-power Syntax display poe-powerDescription on fields of the display poe pse command Description on fields of the display poe-power command 2493 Existing PoE configuration files will be displayed Display poe-profileDisplay poe-profile index index name profile-name Number ranges from 1 to Description on fields of the display poe-profile command 2495 Display poe-profile interface Poe disconnectSyntax poe disconnect ac dc Undo poe disconnect Poe enable Syntax poe enable Undo poe enable Poe enable pse Poe legacy enable Poe max-power Poe max-power system viewSyntax poe max-power max-power Undo poe max-power 2499 Poe mode Related command poe priority system viewPoe mode signal spare Undo poe mode Poe pd-description Poe pd-policy prioritySyntax poe pd-description string Undo poe pd-description Syntax poe pd-policy priority Undo poe pd-policy priority Poe priority Syntax poe priority critical high low Undo poe priority Poe priority system view Poe priority critical high low pse pse-idUndo poe priority pse pse-id Poe update Poe update full refresh filename pse pse-idPoe pse-policy priority Poe pse-policy priority Example # Set the power alarm threshold of PSE 2 to 90% Poe utilization-thresholdPoe-profile Undo poe utilization-threshold pse pse-id Sysname system-view Sysname poe-profile abc OAP Module Configuration Commands Oap connect slotSyntax oap connect slot slot-number Oap reboot slot Syntax oap reboot slot slot-number Acfp Configuration Commands Acfp enable168 Display acfp client-info Display acfp policy-info Client-idis the Acfp client ID, in the range of 1 toPolicy-index Policy index, in the range of 1 to Interface-numberis the interface type and interface number 2511 Display acfp rule-cache Interface type and interface numberInterface-number is the interface type and interface number Will display all the Acfp rule cache information Display acfp rule-info Interface numberClient-id Acfp client ID, in the range of 1 to 2513 # Display Acfp rule information in order of policy Establish Display acfp server-info Syntax display acfp server-info2515 Reset acfp rule-cache Type and interface number Acsei Server Configuration Commands Acsei server enableSyntax acsei server enable Undo acsei server enable Acsei server Acsei timer clock-sync Acsei timer monitorSyntax acsei timer monitor seconds Undo acsei timer monitor Acsei client reboot Acsei client closeDisplay acsei client summary Display acsei client info # Display the summary of all Acsei clientsSyntax display acsei client info client-id # Display information about all Acsei clients 2521 CPU information of the Acsei client Acsei Client Configuration Commands Acsei-client debug disableAcsei-client debug enable 170 Chkconfig acseid off Syntax chkconfig acseid offAcsei-client debug show Syntax acsei-client debug show Chkconfig acseid on Service acseid condrestartSyntax chkconfig acseid on Syntax service acseid condrestart Service acseid reload Service acseid restartService acseid reload # Load the Acsei client configuration file Service acseid start Service acseid statusSyntax service acseid start Syntax service acseid status Service acseid stop Service acseid stopAny directory of the Linux system # Stop an Acsei client that is running Track Configuration Commands Description on the fields of the display track command171 Display track Track Configuration Commands IPX Configuration Commands 172Display ipx interface Display ipx routing-table Syntax display ipx routing-table network Display ipx routing-table verbose Syntax display ipx routing-table network verbose2533 Display ipx routing-table protocol Display ipx service-table Inactive Displays inactive service informationDisplay ipx routing-table statistics To 47 characters # Display detailed IPX service information Display ipx statisticsSyntax display ipx statistics 2537 SAP Ipx enable Ipx enable node nodeUndo ipx enable Configuration Ipx netbios-propagation Syntax ipx netbios-propagation Undo ipx netbios-propagationIpx encapsulation Ipx encapsulation dot2 dot3 ethernet-2 snap Ipx network Ipx rip import-route staticUndo ipx network Ipx rip import-route static Example # Enable static route redistribution to RIP Ipx rip mtuIpx rip multiplier Syntax ipx rip mtu bytes Undo ipx rip mtu Ipx rip timer update Related command ipx rip timer updateRelated command ipx rip multiplier Example # Specify a RIP update interval of 30 seconds Ipx route load-balance-path 2543 Ipx sap disable Syntax ipx sap disable Undo ipx sap disableIpx route max-reserve-path Ipx sap gns-disable-reply Ipx sap gns-disable-replyUndo ipx sap gns-disable-reply Ipx sap gns-load-balance Related command ipx sap gns-disable-reply Ipx sap max-reserve-serversIpx sap mtu Syntax ipx sap mtu bytes Related command ipx sap timer update Ipx sap multiplierUndo ipx sap mtu 2547 Ipx sap timer update Ipx serviceRelated command ipx sap multiplier, ipx update-change-only Example # Specify the SAP updating interval as 300 seconds Ipx split-horizon Ipx tickIpx split-horizon Undo ipx split-horizon Ipx update-change-only Syntax ipx update-change-only Undo ipx update-change-onlyPing ipx Reset ipx statistics Reset ipx routing-table statistics protocolSyntax reset ipx statistics 2551 Related command display ipx routing-table statistics Example # Display IPX routing statistics# Clear IPX static route statistics Voip Configuration Commands 173 Area Area-idArea custom europe north-america Undo area Related command match-template,address, and entity Busytone-t-thSyntax busytone-t-th time-threshold Undo busytone-t-th 2555 Cid display Cid receiveSyntax cid display Undo cid display Syntax cid receive Undo cid receive Cid send Cid typeSyntax cid send Undo cid send View FXS/FXO voice subscriber line view Cng-on Undo cid typeSyntax cng-on Undo cng-on Related command line and vad-on CompressionView POTS/VoIP/VoFR entity view 2559 Relationship between algorithms and bandwidth Codec Bandwidth Voice quality 711 algorithm A-law and µ-law 723 r63 algorithm723 r53 algorithm 726 r16 algorithm 726 r24 algorithm 726 r32 algorithm726 r40 algorithm Algorithm Compression efficiency of IPHC+PPP header Cptone country-type Syntax cptone country-type locale Undo cptone country-typeRegions are supported Countries or regions with supported call progress tones 2565 IEU Cptone tone-type Effect on all voice interfaces of all cards on the deviceSpecial-dial-tone waiting-tone amplitude value Special-dial-tone waiting-tone amplitude Default entity compression G729r8 Default entity payload-size Related command compression Default entity vad-on Default entity vad-onUndo default entity vad-on Vad-on Default subscriber-line Delay holdTransmit gain Delay rising Delay send-dtmfRelated command em-signal Syntax delay rising milliseconds Undo delay rising Delay send-wink Syntax delay send-wink milliseconds Undo delay send-wink Delay wink-hold Delay wink-risingSyntax delay wink-hold milliseconds Undo delay wink-hold 2573 Delay start-dial Syntax delay start-dial seconds Undo delay start-dialDescription voice entity view Description voice subscriber line view Dial-programSyntax dial-program View Voice view Display voice call-info Display voice call-info brief mark tag verboseRange of 0 to Information table Display voice cmc LGS Display voice default all Syntax display voice default allDescription on fields of the display voice cmc command 2579 Description on fields of the display voice default command Display voice entity command Example Display voice entityDisplay voice ipp statistic Display voice entity all mark entity-tag pots voip Voip Configuration Commands Error Displays all the error statistics of IVA module Display voice iva statisticCall Displays the calling statistics in the IVA module 2583 Related command subscriber-line Display voice subscriber-lineSyntax display voice subscriber-line line-number 2585 = Busytone CNG Dscp media Dtmf amplitudeSyntax dscp media dscp-value Undo dscp media Syntax dtmf amplitude value Undo dtmf amplitude Dtmf sensitivity-level Dtmf timeDtmf time interval persist milliseconds Undo dtmf time interval persist Dtmf threshold Meaning of the index numbers2589 Index Meaning Value range Remarks Upper limit of the maximum To 4,999, with Echo-canceller 2591 Echo-canceller parameter Related command subscriber-lineand echo-canceller parameterMix-proportion-ratio value talk-threshold value Mix-proportion-ratio talk-threshold Em-signal Related command echo-cancellerEm-phy-parm Entity Entity entity-number pots voipUndo entity entity-numberall pots voip Related command Line Example Related command outband, tunnel-on, and voip called-startFast-connect Fast-connect Hookoff-mode delay bind Example # Enable fast connection for VoIP voice entitySyntax hookoff-mode delay immediate Undo hookoff-mode Hookoff-mode Private-lineand caller-permitcommands when executing Hookoff-timeIncoming calls Syntax hookoff-time time Undo hookoff-time Impedance Line Match-templateUndo line Syntax match-template match-string Undo match-template Them If you want to use and at the same time, you must use themFormat . Other formats, such as and are illegal Such as 0-9. The formats like 0-A are illegal Command, but analog voice subscriber lines do not Nlp-onE1 voice, T, #, and * are not supported currently Nlp-on Related command Fast-connectand tunnel-on Example OutbandPayload-size Plc-mode Syntax plc-mode general specific Undo plc-mode2603 Related command transmit gain and subscriber-line Receive gainSyntax receive gain value Undo receive gain Reset voice cmc statistic Register-numberMatch-template Reset voice ipp statistic Reset voice iva statisticRelated command display voice iva statistic Related command display voice ipp statistic Send-busytone enable time seconds Undo send-busytone enable timeSend-busytone Been used to identify nonstandard T38 fax packets Send-ring Shutdown voice entity viewSyntax send-ring Undo send-ring View Voice entity view Shutdown voice subscriber line view Silence-th-spanExample # Change the status of voice entity 4 to Down Undo silence-th-span Slic-gain Subscriber-lineSlic-gain 0 Undo slic-gain Timer dial-interval Syntax timer dial-interval seconds Undo timer dial-interval2611 Timer first-dial Timer hookoff-intervalSyntax timer first-dial seconds Undo timer first-dial Timer ring-back Timer wait-digitRelated command hookoff-mode Syntax timer ring-back seconds Undo timer ring-back Related command receive gain and subscriber-line Transmit gainSyntax transmit gain value Undo transmit gain Example # Enable the tunnel function for VoIP voice entity Tunnel-onSyntax tunnel-on Undo tunnel-on View VoIP entity view Related command cng-on Vad-onUndo type Syntax vad-on Vi-card busy-tone-detect Undo vi-card busy-tone-detect custom index2617 Vi-card cptone-custom Vi-card reboot Syntax vi-card reboot slot-number2619 Voice-setup Voip called-tunnel enableExample # Reset the voice card of slot Syntax voice-setup Voip timer Voip called-startFast-connect Vqa dscp Cs7, or efDscp values Keyword Dscp value in binary Dscp value in decimal By default, DSP buffered data is not monitored Vqa dsp-monitor buffer-timeView Voice view Parameter Range 180 to Voip Configuration Commands Dial Plan Configuration Commands Caller-permit Related command match-templateon Dial-prefixSyntax dial-prefix string Undo dial-prefix Related command match-templateon page 2599 and send-number Display voice number-substituteExample # Specify 0 as a prefix Syntax display voice number-substitute list-tag Related command number-substitute Dot-matchDot-match end-only left-right right-left Undo dot-match First-rule Max-call in voice dial program viewSyntax first-rule rule-number Undo first-rule Undo max-call set-numberI all Related command max-call in voice entity view Max-call in voice entity viewUndo max-call Related command max-call in voice dial program view Related command match-templateon page 2599 and terminatorExample # Configure the longest-number match policy Number-match Related command rule and substitute voice dial program view Number-priorityNumber-substitute Priority Private-lineUndo priority Syntax private-line string Undo private-line Rule Undo rule rule-tag all Meanings of characters in the string argument 2635 Input number type Number type DescriptionNumbering plan Description Input numbering plan Output numbering plan2637 Select-rule rule-order Undo select-rule rule-order Select-rule search-stop Meanings of integers2639 Integer Meaning Description Select-rule type-first Undo select-rule type-firstMeanings of values Select-stop Syntax select-stop Undo select-stop2641 Related command dot-matchand match-templateon Send-number Related command number-substituteand rule Substitute subscriber line view/voice entity viewSubstitute called calling list-number Undo substitute called calling Substitute voice dial program view AllNumber-substitute and rule To Pstn are outgoing calls Related command match-templateon page 2599 and timer TerminatorSyntax terminator character Undo terminator Example # Specify the pound sign # as the dial terminator Dial Plan Configuration Commands E1 and T1 Configuration Commands AniAni all ka Undo ani Answer enable Related command cas, timer, reverse, and renewSyntax answer enable Undo answer enable Ani-offset Related command re-answer enable and timer dl re-answer CallmodeCas Callmode segment terminal Clear-forward-ack enable Example # Enter the R2 CAS view of TS group Related command mode Display voice subscriber line2651 Dl-bits CNG/CED Default values of signals in R2 digital line signaling Signal Default rx-bits Abcd Default tx-bits Abcd2653 Dtmf enable Related command seizure-ack enable and answer enableSyntax dtmf enable Undo dtmf enable Related command timer dtmf Final-callednum enable Syntax final-callednum enable Undo final-callednum enableRelated command register-valuedigital-end 2655 Force-metering enable Group-b enableSyntax force-metering enable Undo force-metering enable Syntax group-b enable Undo group-b enable Related command register-valuereq-switch-groupb 2657 Syntax mode zone-name default-standard Undo mode Mode Related command register-valueand force-metering enable Example # Adopt Hongkong default R2 signalingPcm Syntax pcm a-law µ-law Undo pcm Example # Adopt µ-law companding for signal quantization Pri-setSyntax pri-set timeslot-list range Undo pri-set Re-answer enable Syntax re-answer enable Undo re-answer enableRelated command answer enable and timer dl re-answer 2661 Req-callednum-and-switchgroupa req-callingcategory req Changeover to Group a signal value, in the range 1 toDemand-refused digit-end nullnum req-billingcategory Subscriber-busy subscriber-charge subscriber-idle 2663 Related command group-b enable RenewSyntax renew Abcd Undo renew Seizure-ack enable Related command cas and reverseRelated command cas and renew Reverse Related command timer dl seizure Select-modeView CAS view Timeslots Sendring ringbusy enable Related command cas and trunk-directionRelated command timer ring 2667 Signal-value Related command Subscriber line ExampleSpecial-character Syntax special-character character number Different signal values Undo special-character character number Related command timeslot-setand pri-set Tdm-clockExample # Enter the view of voice subscriber line 1/015 Syntax tdm-clock internal line primary Undo tdm-clock Timer dl Release-guardView R2 CAS view 2671 Timer dtmf Syntax timer dtmf time Undo timer dtmf Timer register-pulse persistence Related command dtmf enableTimer register-pulse persistence time Undo timer register-pulse persistence Timer register-complete group-b Related command timer register-completegroup-bTimer register-complete group-b time Undo timer register-complete group-b Timer ring Timer ring ringback ringbusy timeUndo timer ring ringback ringbusy Timeslot-set Related command subscriber line and cas Trunk-direction Related command cas and select-mode Ts block open query reset timeslots timeslots-listCAS view 2677 Related command cas FAX Over IP Configuration Commands Default entity fax Display voice fax Example # Set the maximum fax rate to 9,600 bps globallySyntax display voice fax statistics 2681 Faxvofrstandardswitch FAXVOFRFRF11SWITCHWaitdpbegdemodulatetimeout Waitdpbegmodulatetimeout Fax baudrate 2400 4800 9600 14400 disable voice Fax baudrateUndo fax baudrate Fax ecm Syntax fax ecmUndo fax ecm Fax level Fax local-train thresholdSyntax fax level level Undo fax level 2685 Example # Configure the fax local training threshold to Example # Configure NSF for fax signal transmissionFax nsf-on Syntax fax nsf-on Undo fax nsf-on Fax protocol Fax protocol pcm g711alaw g711 μlawUndo fax protocol VoFR entities only support the PPP training mode Fax train-modeFax train-mode local ppp Undo fax train-mode Reset voice fax statistics Reset voice fax statisticsVoip h323-conf tcs-t38 Voip h323-conf tcs-t38 FAX Over IP Configuration Commands Related command match-templateon page 2599, entity on 177Display voice gateway Syntax area-id string Undo area-id string Gk-client Syntax gk-clientGkid Related command gk-id Gk-2nd-idExample # Enter gatekeeper client view Undo gk-2nd-id Gk-security call enable Related command area-id,gw-id,gk-2nd-id,gw-address,ras-onSyntax gk-security call enable Undo gk-security call enable Gk-id Gk-security register-pwd cipher simple password Gk-security register-pwdGw-address Undo gk-security register-pwd Gw-id Undo gw-addressUndo gw-id Related command gw-id,gw-address, and gk-id Ras-onVoip h323-descriptor Syntax ras-on 323 Configuration Commands SIP Configuration Commands 178Display voice sip call-statistics Syntax display voice sip call-statistics TPT Message Display voice sip register-state Outband sipDisplay voice sip register-state Syntax outband sip Undo outband Default port number is ProxyUndo proxy ipv4 SIP client view Register-enable Register-enable off onUndo register-enable Registrar ipv4 Reset voice sip SipSip-comp Syntax sip Sip-comp agent Undo sip-comp callee fromSIP client view SIP request messages Sip-comp server Sip-domainUndo sip-comp server View SIP client view Source-ip Syntax source-ip ip-address Undo source-ip2707 SIP Configuration Commands Wildcard-register enable Syntax wildcard-register enable Undo wildcard-registerExample # Enable fuzzy telephone number registration 2709 SIP Configuration Commands Vofr Configuration Commands 179Address Undo address vofr-dynamic vofr-static Related command Trunk-idand address Example Call-modeCid select-mode Related command Vofr Example # Set the CID selection mode to min-poll on DlciDisplay fr vofr-info Interface Dlci view Entity vofr Outband vofrUndo entity entity-number vofr Outband vofr Seq-number Seq-numberUndo seq-number Related command call-mode TimestampTrunk-id Voice bandwidth VofrView Interface Dlci view 2717 Related command call-mode Vofr frf11-timer Vofr frf11-timer timeUndo vofr frf11-timer Hang up successfully in the FRF.11 trunk mode Vofr Configuration Commands Voice Radius Configuration Commands Aaa-clientAccounting Syntax aaa-client Related command acct-methodand accounting Accounting-didSyntax accounting-did Undo accounting-did View Voice AAA client view Related command accounting and accounting-did # Restore the default accounting methodAcct-method Example # Set the accounting method to start-ack Authentication Authentication-didSyntax authentication Undo authentication Related command gw-access-numberand authorization Authorization Related command authorization-didSyntax authorization Undo authorization 2725 Authorization-did Related command gw-access-numberand authenticationSyntax authorization-did Undo authorization-did Related command authentication-did Related command gw-access-number Callednumber receive-method2727 Related command gw-access-numberand process-config Card-digitCdr Syntax card-digit card-digit Undo card-digit Related command display voice call-history-record # Set the alarm threshold for CDRs to 10%Undo cdr all buffer duration threshold Example # Set the number of CDRs that can be saved to Display voice access-number Display voice access-numberGw-access-number and aaa-client 2731 Display voice call-history-record Related command cdr Example # Display call records by calling number2733 Display voice radius statistic Syntax display voice radius statistic Related command reset voice radius statistic 2735VORDS=AAA AAA=VORDS Gw-access-number CMC=VORDS Password-digit # Add the access number 179 and enter access number view# Delete the access number # Delete all access numbers Process-config # Restore the default dialing process for the access number 2739 Redialtimes Undo redialtimes Reset voice radius statistic Gw-access-numberand process-configSelectlanguage Display voice radius statistic Voice Radius Configuration Commands

3Com MSR 30 Display interface virtual-template, Syntax display interface virtual-template number

Models: MSR 50 MSR 30

Field